diff options
Diffstat (limited to 'drivers/ide/ide-cd.h')
| -rw-r--r-- | drivers/ide/ide-cd.h | 746 |
1 files changed, 746 insertions, 0 deletions
diff --git a/drivers/ide/ide-cd.h b/drivers/ide/ide-cd.h new file mode 100644 index 00000000000..7ca3e5afc66 --- /dev/null +++ b/drivers/ide/ide-cd.h @@ -0,0 +1,746 @@ +/* + * linux/drivers/ide/ide_cd.h + * + * Copyright (C) 1996-98 Erik Andersen + * Copyright (C) 1998-2000 Jens Axboe + */ +#ifndef _IDE_CD_H +#define _IDE_CD_H + +#include <linux/cdrom.h> +#include <asm/byteorder.h> + +/* Turn this on to have the driver print out the meanings of the + ATAPI error codes. This will use up additional kernel-space + memory, though. */ + +#ifndef VERBOSE_IDE_CD_ERRORS +#define VERBOSE_IDE_CD_ERRORS 1 +#endif + + +/* Turning this on will remove code to work around various nonstandard + ATAPI implementations. If you know your drive follows the standard, + this will give you a slightly smaller kernel. */ + +#ifndef STANDARD_ATAPI +#define STANDARD_ATAPI 0 +#endif + + +/* Turning this on will disable the door-locking functionality. + This is apparently needed for supermount. */ + +#ifndef NO_DOOR_LOCKING +#define NO_DOOR_LOCKING 0 +#endif + +/* + * typical timeout for packet command + */ +#define ATAPI_WAIT_PC (60 * HZ) +#define ATAPI_WAIT_WRITE_BUSY (10 * HZ) + +/************************************************************************/ + +#define SECTOR_BITS 9 +#ifndef SECTOR_SIZE +#define SECTOR_SIZE (1 << SECTOR_BITS) +#endif +#define SECTORS_PER_FRAME (CD_FRAMESIZE >> SECTOR_BITS) +#define SECTOR_BUFFER_SIZE (CD_FRAMESIZE * 32) +#define SECTORS_BUFFER (SECTOR_BUFFER_SIZE >> SECTOR_BITS) +#define SECTORS_MAX (131072 >> SECTOR_BITS) + +#define BLOCKS_PER_FRAME (CD_FRAMESIZE / BLOCK_SIZE) + +/* special command codes for strategy routine. */ +#define PACKET_COMMAND 4315 +#define REQUEST_SENSE_COMMAND 4316 +#define RESET_DRIVE_COMMAND 4317 + + +/* Configuration flags. These describe the capabilities of the drive. + They generally do not change after initialization, unless we learn + more about the drive from stuff failing. */ +struct ide_cd_config_flags { + __u8 drq_interrupt : 1; /* Device sends an interrupt when ready + for a packet command. */ + __u8 no_doorlock : 1; /* Drive cannot lock the door. */ + __u8 no_eject : 1; /* Drive cannot eject the disc. */ + __u8 nec260 : 1; /* Drive is a pre-1.2 NEC 260 drive. */ + __u8 playmsf_as_bcd : 1; /* PLAYMSF command takes BCD args. */ + __u8 tocaddr_as_bcd : 1; /* TOC addresses are in BCD. */ + __u8 toctracks_as_bcd : 1; /* TOC track numbers are in BCD. */ + __u8 subchan_as_bcd : 1; /* Subchannel info is in BCD. */ + __u8 is_changer : 1; /* Drive is a changer. */ + __u8 cd_r : 1; /* Drive can write to CD-R media . */ + __u8 cd_rw : 1; /* Drive can write to CD-R/W media . */ + __u8 dvd : 1; /* Drive is a DVD-ROM */ + __u8 dvd_r : 1; /* Drive can write DVD-R */ + __u8 dvd_ram : 1; /* Drive can write DVD-RAM */ + __u8 ram : 1; /* generic WRITE (dvd-ram/mrw) */ + __u8 test_write : 1; /* Drive can fake writes */ + __u8 supp_disc_present : 1; /* Changer can report exact contents + of slots. */ + __u8 limit_nframes : 1; /* Drive does not provide data in + multiples of SECTOR_SIZE when more + than one interrupt is needed. */ + __u8 seeking : 1; /* Seeking in progress */ + __u8 audio_play : 1; /* can do audio related commands */ + __u8 close_tray : 1; /* can close the tray */ + __u8 writing : 1; /* pseudo write in progress */ + __u8 mo_drive : 1; /* drive is an MO device */ + __u8 reserved : 2; + byte max_speed; /* Max speed of the drive */ +}; +#define CDROM_CONFIG_FLAGS(drive) (&(((struct cdrom_info *)(drive->driver_data))->config_flags)) + + +/* State flags. These give information about the current state of the + drive, and will change during normal operation. */ +struct ide_cd_state_flags { + __u8 media_changed : 1; /* Driver has noticed a media change. */ + __u8 toc_valid : 1; /* Saved TOC information is current. */ + __u8 door_locked : 1; /* We think that the drive door is locked. */ + __u8 writing : 1; /* the drive is currently writing */ + __u8 reserved : 4; + byte current_speed; /* Current speed of the drive */ +}; + +#define CDROM_STATE_FLAGS(drive) (&(((struct cdrom_info *)(drive->driver_data))->state_flags)) + +/* Structure of a MSF cdrom address. */ +struct atapi_msf { + byte reserved; + byte minute; + byte second; + byte frame; +}; + +/* Space to hold the disk TOC. */ +#define MAX_TRACKS 99 +struct atapi_toc_header { + unsigned short toc_length; + byte first_track; + byte last_track; +}; + +struct atapi_toc_entry { + byte reserved1; +#if defined(__BIG_ENDIAN_BITFIELD) + __u8 adr : 4; + __u8 control : 4; +#elif defined(__LITTLE_ENDIAN_BITFIELD) + __u8 control : 4; + __u8 adr : 4; +#else +#error "Please fix <asm/byteorder.h>" +#endif + byte track; + byte reserved2; + union { + unsigned lba; + struct atapi_msf msf; + } addr; +}; + +struct atapi_toc { + int last_session_lba; + int xa_flag; + unsigned long capacity; + struct atapi_toc_header hdr; + struct atapi_toc_entry ent[MAX_TRACKS+1]; + /* One extra for the leadout. */ +}; + + +/* This structure is annoyingly close to, but not identical with, + the cdrom_subchnl structure from cdrom.h. */ +struct atapi_cdrom_subchnl { + u_char acdsc_reserved; + u_char acdsc_audiostatus; + u_short acdsc_length; + u_char acdsc_format; + +#if defined(__BIG_ENDIAN_BITFIELD) + u_char acdsc_ctrl: 4; + u_char acdsc_adr: 4; +#elif defined(__LITTLE_ENDIAN_BITFIELD) + u_char acdsc_adr: 4; + u_char acdsc_ctrl: 4; +#else +#error "Please fix <asm/byteorder.h>" +#endif + u_char acdsc_trk; + u_char acdsc_ind; + union { + struct atapi_msf msf; + int lba; + } acdsc_absaddr; + union { + struct atapi_msf msf; + int lba; + } acdsc_reladdr; +}; + + + +/* This should probably go into cdrom.h along with the other + * generic stuff now in the Mt. Fuji spec. + */ +struct atapi_capabilities_page { + struct mode_page_header header; +#if defined(__BIG_ENDIAN_BITFIELD) + __u8 parameters_saveable : 1; + __u8 reserved1 : 1; + __u8 page_code : 6; +#elif defined(__LITTLE_ENDIAN_BITFIELD) + __u8 page_code : 6; + __u8 reserved1 : 1; + __u8 parameters_saveable : 1; +#else +#error "Please fix <asm/byteorder.h>" +#endif + + byte page_length; + +#if defined(__BIG_ENDIAN_BITFIELD) + __u8 reserved2 : 2; + /* Drive supports reading of DVD-RAM discs */ + __u8 dvd_ram_read : 1; + /* Drive supports reading of DVD-R discs */ + __u8 dvd_r_read : 1; + /* Drive supports reading of DVD-ROM discs */ + __u8 dvd_rom : 1; + /* Drive supports reading CD-R discs with addressing method 2 */ + __u8 method2 : 1; /* reserved in 1.2 */ + /* Drive can read from CD-R/W (CD-E) discs (orange book, part III) */ + __u8 cd_rw_read : 1; /* reserved in 1.2 */ + /* Drive supports read from CD-R discs (orange book, part II) */ + __u8 cd_r_read : 1; /* reserved in 1.2 */ +#elif defined(__LITTLE_ENDIAN_BITFIELD) + /* Drive supports read from CD-R discs (orange book, part II) */ + __u8 cd_r_read : 1; /* reserved in 1.2 */ + /* Drive can read from CD-R/W (CD-E) discs (orange book, part III) */ + __u8 cd_rw_read : 1; /* reserved in 1.2 */ + /* Drive supports reading CD-R discs with addressing method 2 */ + __u8 method2 : 1; + /* Drive supports reading of DVD-ROM discs */ + __u8 dvd_rom : 1; + /* Drive supports reading of DVD-R discs */ + __u8 dvd_r_read : 1; + /* Drive supports reading of DVD-RAM discs */ + __u8 dvd_ram_read : 1; + __u8 reserved2 : 2; +#else +#error "Please fix <asm/byteorder.h>" +#endif + +#if defined(__BIG_ENDIAN_BITFIELD) + __u8 reserved3 : 2; + /* Drive can write DVD-RAM discs */ + __u8 dvd_ram_write : 1; + /* Drive can write DVD-R discs */ + __u8 dvd_r_write : 1; + __u8 reserved3a : 1; + /* Drive can fake writes */ + __u8 test_write : 1; + /* Drive can write to CD-R/W (CD-E) discs (orange book, part III) */ + __u8 cd_rw_write : 1; /* reserved in 1.2 */ + /* Drive supports write to CD-R discs (orange book, part II) */ + __u8 cd_r_write : 1; /* reserved in 1.2 */ +#elif defined(__LITTLE_ENDIAN_BITFIELD) + /* Drive can write to CD-R discs (orange book, part II) */ + __u8 cd_r_write : 1; /* reserved in 1.2 */ + /* Drive can write to CD-R/W (CD-E) discs (orange book, part III) */ + __u8 cd_rw_write : 1; /* reserved in 1.2 */ + /* Drive can fake writes */ + __u8 test_write : 1; + __u8 reserved3a : 1; + /* Drive can write DVD-R discs */ + __u8 dvd_r_write : 1; + /* Drive can write DVD-RAM discs */ + __u8 dvd_ram_write : 1; + __u8 reserved3 : 2; +#else +#error "Please fix <asm/byteorder.h>" +#endif + +#if defined(__BIG_ENDIAN_BITFIELD) + __u8 reserved4 : 1; + /* Drive can read multisession discs. */ + __u8 multisession : 1; + /* Drive can read mode 2, form 2 data. */ + __u8 mode2_form2 : 1; + /* Drive can read mode 2, form 1 (XA) data. */ + __u8 mode2_form1 : 1; + /* Drive supports digital output on port 2. */ + __u8 digport2 : 1; + /* Drive supports digital output on port 1. */ + __u8 digport1 : 1; + /* Drive can deliver a composite audio/video data stream. */ + __u8 composite : 1; + /* Drive supports audio play operations. */ + __u8 audio_play : 1; +#elif defined(__LITTLE_ENDIAN_BITFIELD) + /* Drive supports audio play operations. */ + __u8 audio_play : 1; + /* Drive can deliver a composite audio/video data stream. */ + __u8 composite : 1; + /* Drive supports digital output on port 1. */ + __u8 digport1 : 1; + /* Drive supports digital output on port 2. */ + __u8 digport2 : 1; + /* Drive can read mode 2, form 1 (XA) data. */ + __u8 mode2_form1 : 1; + /* Drive can read mode 2, form 2 data. */ + __u8 mode2_form2 : 1; + /* Drive can read multisession discs. */ + __u8 multisession : 1; + __u8 reserved4 : 1; +#else +#error "Please fix <asm/byteorder.h>" +#endif + +#if defined(__BIG_ENDIAN_BITFIELD) + __u8 reserved5 : 1; + /* Drive can return Media Catalog Number (UPC) info. */ + __u8 upc : 1; + /* Drive can return International Standard Recording Code info. */ + __u8 isrc : 1; + /* Drive supports C2 error pointers. */ + __u8 c2_pointers : 1; + /* R-W data will be returned deinterleaved and error corrected. */ + __u8 rw_corr : 1; + /* Subchannel reads can return combined R-W information. */ + __u8 rw_supported : 1; + /* Drive can continue a read cdda operation from a loss of streaming.*/ + __u8 cdda_accurate : 1; + /* Drive can read Red Book audio data. */ + __u8 cdda : 1; +#elif defined(__LITTLE_ENDIAN_BITFIELD) + /* Drive can read Red Book audio data. */ + __u8 cdda : 1; + /* Drive can continue a read cdda operation from a loss of streaming.*/ + __u8 cdda_accurate : 1; + /* Subchannel reads can return combined R-W information. */ + __u8 rw_supported : 1; + /* R-W data will be returned deinterleaved and error corrected. */ + __u8 rw_corr : 1; + /* Drive supports C2 error pointers. */ + __u8 c2_pointers : 1; + /* Drive can return International Standard Recording Code info. */ + __u8 isrc : 1; + /* Drive can return Media Catalog Number (UPC) info. */ + __u8 upc : 1; + __u8 reserved5 : 1; +#else +#error "Please fix <asm/byteorder.h>" +#endif + +#if defined(__BIG_ENDIAN_BITFIELD) + /* Drive mechanism types. */ + mechtype_t mechtype : 3; + __u8 reserved6 : 1; + /* Drive can eject a disc or changer cartridge. */ + __u8 eject : 1; + /* State of prevent/allow jumper. */ + __u8 prevent_jumper : 1; + /* Present state of door lock. */ + __u8 lock_state : 1; + /* Drive can lock the door. */ + __u8 lock : 1; +#elif defined(__LITTLE_ENDIAN_BITFIELD) + + /* Drive can lock the door. */ + __u8 lock : 1; + /* Present state of door lock. */ + __u8 lock_state : 1; + /* State of prevent/allow jumper. */ + __u8 prevent_jumper : 1; + /* Drive can eject a disc or changer cartridge. */ + __u8 eject : 1; + __u8 reserved6 : 1; + /* Drive mechanism types. */ + mechtype_t mechtype : 3; +#else +#error "Please fix <asm/byteorder.h>" +#endif + +#if defined(__BIG_ENDIAN_BITFIELD) + __u8 reserved7 : 4; + /* Drive supports software slot selection. */ + __u8 sss : 1; /* reserved in 1.2 */ + /* Changer can report exact contents of slots. */ + __u8 disc_present : 1; /* reserved in 1.2 */ + /* Audio for each channel can be muted independently. */ + __u8 separate_mute : 1; + /* Audio level for each channel can be controlled independently. */ + __u8 separate_volume : 1; +#elif defined(__LITTLE_ENDIAN_BITFIELD) + + /* Audio level for each channel can be controlled independently. */ + __u8 separate_volume : 1; + /* Audio for each channel can be muted independently. */ + __u8 separate_mute : 1; + /* Changer can report exact contents of slots. */ + __u8 disc_present : 1; /* reserved in 1.2 */ + /* Drive supports software slot selection. */ + __u8 sss : 1; /* reserved in 1.2 */ + __u8 reserved7 : 4; +#else +#error "Please fix <asm/byteorder.h>" +#endif + + /* Note: the following four fields are returned in big-endian form. */ + /* Maximum speed (in kB/s). */ + unsigned short maxspeed; + /* Number of discrete volume levels. */ + unsigned short n_vol_levels; + /* Size of cache in drive, in kB. */ + unsigned short buffer_size; + /* Current speed (in kB/s). */ + unsigned short curspeed; + char pad[4]; +}; + + +struct atapi_mechstat_header { +#if defined(__BIG_ENDIAN_BITFIELD) + __u8 fault : 1; + __u8 changer_state : 2; + __u8 curslot : 5; +#elif defined(__LITTLE_ENDIAN_BITFIELD) + __u8 curslot : 5; + __u8 changer_state : 2; + __u8 fault : 1; +#else +#error "Please fix <asm/byteorder.h>" +#endif + +#if defined(__BIG_ENDIAN_BITFIELD) + __u8 mech_state : 3; + __u8 door_open : 1; + __u8 reserved1 : 4; +#elif defined(__LITTLE_ENDIAN_BITFIELD) + __u8 reserved1 : 4; + __u8 door_open : 1; + __u8 mech_state : 3; +#else +#error "Please fix <asm/byteorder.h>" +#endif + + byte curlba[3]; + byte nslots; + __u16 slot_tablelen; +}; + + +struct atapi_slot { +#if defined(__BIG_ENDIAN_BITFIELD) + __u8 disc_present : 1; + __u8 reserved1 : 6; + __u8 change : 1; +#elif defined(__LITTLE_ENDIAN_BITFIELD) + __u8 change : 1; + __u8 reserved1 : 6; + __u8 disc_present : 1; +#else +#error "Please fix <asm/byteorder.h>" +#endif + + byte reserved2[3]; +}; + +struct atapi_changer_info { + struct atapi_mechstat_header hdr; + struct atapi_slot slots[0]; +}; + +/* Extra per-device info for cdrom drives. */ +struct cdrom_info { + ide_drive_t *drive; + ide_driver_t *driver; + struct gendisk *disk; + struct kref kref; + + /* Buffer for table of contents. NULL if we haven't allocated + a TOC buffer for this device yet. */ + + struct atapi_toc *toc; + + unsigned long sector_buffered; + unsigned long nsectors_buffered; + unsigned char *buffer; + + /* The result of the last successful request sense command + on this device. */ + struct request_sense sense_data; + + struct request request_sense_request; + int dma; + int cmd; + unsigned long last_block; + unsigned long start_seek; + /* Buffer to hold mechanism status and changer slot table. */ + struct atapi_changer_info *changer_info; + + struct ide_cd_config_flags config_flags; + struct ide_cd_state_flags state_flags; + + /* Per-device info needed by cdrom.c generic driver. */ + struct cdrom_device_info devinfo; + + unsigned long write_timeout; +}; + +/**************************************************************************** + * Descriptions of ATAPI error codes. + */ + +#define ARY_LEN(a) ((sizeof(a) / sizeof(a[0]))) + +/* This stuff should be in cdrom.h, since it is now generic... */ + +/* ATAPI sense keys (from table 140 of ATAPI 2.6) */ +#define NO_SENSE 0x00 +#define RECOVERED_ERROR 0x01 +#define NOT_READY 0x02 +#define MEDIUM_ERROR 0x03 +#define HARDWARE_ERROR 0x04 +#define ILLEGAL_REQUEST 0x05 +#define UNIT_ATTENTION 0x06 +#define DATA_PROTECT 0x07 +#define BLANK_CHECK 0x08 +#define ABORTED_COMMAND 0x0b +#define MISCOMPARE 0x0e + + + +/* This stuff should be in cdrom.h, since it is now generic... */ +#if VERBOSE_IDE_CD_ERRORS + + /* The generic packet command opcodes for CD/DVD Logical Units, + * From Table 57 of the SFF8090 Ver. 3 (Mt. Fuji) draft standard. */ +static const struct { + unsigned short packet_command; + const char * const text; +} packet_command_texts[] = { + { GPCMD_TEST_UNIT_READY, "Test Unit Ready" }, + { GPCMD_REQUEST_SENSE, "Request Sense" }, + { GPCMD_FORMAT_UNIT, "Format Unit" }, + { GPCMD_INQUIRY, "Inquiry" }, + { GPCMD_START_STOP_UNIT, "Start/Stop Unit" }, + { GPCMD_PREVENT_ALLOW_MEDIUM_REMOVAL, "Prevent/Allow Medium Removal" }, + { GPCMD_READ_FORMAT_CAPACITIES, "Read Format Capacities" }, + { GPCMD_READ_CDVD_CAPACITY, "Read Cd/Dvd Capacity" }, + { GPCMD_READ_10, "Read 10" }, + { GPCMD_WRITE_10, "Write 10" }, + { GPCMD_SEEK, "Seek" }, + { GPCMD_WRITE_AND_VERIFY_10, "Write and Verify 10" }, + { GPCMD_VERIFY_10, "Verify 10" }, + { GPCMD_FLUSH_CACHE, "Flush Cache" }, + { GPCMD_READ_SUBCHANNEL, "Read Subchannel" }, + { GPCMD_READ_TOC_PMA_ATIP, "Read Table of Contents" }, + { GPCMD_READ_HEADER, "Read Header" }, + { GPCMD_PLAY_AUDIO_10, "Play Audio 10" }, + { GPCMD_GET_CONFIGURATION, "Get Configuration" }, + { GPCMD_PLAY_AUDIO_MSF, "Play Audio MSF" }, + { GPCMD_PLAYAUDIO_TI, "Play Audio TrackIndex" }, + { GPCMD_GET_EVENT_STATUS_NOTIFICATION, "Get Event Status Notification" }, + { GPCMD_PAUSE_RESUME, "Pause/Resume" }, + { GPCMD_STOP_PLAY_SCAN, "Stop Play/Scan" }, + { GPCMD_READ_DISC_INFO, "Read Disc Info" }, + { GPCMD_READ_TRACK_RZONE_INFO, "Read Track Rzone Info" }, + { GPCMD_RESERVE_RZONE_TRACK, "Reserve Rzone Track" }, + { GPCMD_SEND_OPC, "Send OPC" }, + { GPCMD_MODE_SELECT_10, "Mode Select 10" }, + { GPCMD_REPAIR_RZONE_TRACK, "Repair Rzone Track" }, + { GPCMD_MODE_SENSE_10, "Mode Sense 10" }, + { GPCMD_CLOSE_TRACK, "Close Track" }, + { GPCMD_BLANK, "Blank" }, + { GPCMD_SEND_EVENT, "Send Event" }, + { GPCMD_SEND_KEY, "Send Key" }, + { GPCMD_REPORT_KEY, "Report Key" }, + { GPCMD_LOAD_UNLOAD, "Load/Unload" }, + { GPCMD_SET_READ_AHEAD, "Set Read-ahead" }, + { GPCMD_READ_12, "Read 12" }, + { GPCMD_GET_PERFORMANCE, "Get Performance" }, + { GPCMD_SEND_DVD_STRUCTURE, "Send DVD Structure" }, + { GPCMD_READ_DVD_STRUCTURE, "Read DVD Structure" }, + { GPCMD_SET_STREAMING, "Set Streaming" }, + { GPCMD_READ_CD_MSF, "Read CD MSF" }, + { GPCMD_SCAN, "Scan" }, + { GPCMD_SET_SPEED, "Set Speed" }, + { GPCMD_PLAY_CD, "Play CD" }, + { GPCMD_MECHANISM_STATUS, "Mechanism Status" }, + { GPCMD_READ_CD, "Read CD" }, +}; + + + +/* From Table 303 of the SFF8090 Ver. 3 (Mt. Fuji) draft standard. */ +static const char * const sense_key_texts[16] = { + "No sense data", + "Recovered error", + "Not ready", + "Medium error", + "Hardware error", + "Illegal request", + "Unit attention", + "Data protect", + "Blank check", + "(reserved)", + "(reserved)", + "Aborted command", + "(reserved)", + "(reserved)", + "Miscompare", + "(reserved)", +}; + +/* From Table 304 of the SFF8090 Ver. 3 (Mt. Fuji) draft standard. */ +static const struct { + unsigned long asc_ascq; + const char * const text; +} sense_data_texts[] = { + { 0x000000, "No additional sense information" }, + { 0x000011, "Play operation in progress" }, + { 0x000012, "Play operation paused" }, + { 0x000013, "Play operation successfully completed" }, + { 0x000014, "Play operation stopped due to error" }, + { 0x000015, "No current audio status to return" }, + { 0x010c0a, "Write error - padding blocks added" }, + { 0x011700, "Recovered data with no error correction applied" }, + { 0x011701, "Recovered data with retries" }, + { 0x011702, "Recovered data with positive head offset" }, + { 0x011703, "Recovered data with negative head offset" }, + { 0x011704, "Recovered data with retries and/or CIRC applied" }, + { 0x011705, "Recovered data using previous sector ID" }, + { 0x011800, "Recovered data with error correction applied" }, + { 0x011801, "Recovered data with error correction and retries applied"}, + { 0x011802, "Recovered data - the data was auto-reallocated" }, + { 0x011803, "Recovered data with CIRC" }, + { 0x011804, "Recovered data with L-EC" }, + { 0x015d00, + "Failure prediction threshold exceeded - Predicted logical unit failure" }, + { 0x015d01, + "Failure prediction threshold exceeded - Predicted media failure" }, + { 0x015dff, "Failure prediction threshold exceeded - False" }, + { 0x017301, "Power calibration area almost full" }, + { 0x020400, "Logical unit not ready - cause not reportable" }, + /* Following is misspelled in ATAPI 2.6, _and_ in Mt. Fuji */ + { 0x020401, + "Logical unit not ready - in progress [sic] of becoming ready" }, + { 0x020402, "Logical unit not ready - initializing command required" }, + { 0x020403, "Logical unit not ready - manual intervention required" }, + { 0x020404, "Logical unit not ready - format in progress" }, + { 0x020407, "Logical unit not ready - operation in progress" }, + { 0x020408, "Logical unit not ready - long write in progress" }, + { 0x020600, "No reference position found (media may be upside down)" }, + { 0x023000, "Incompatible medium installed" }, + { 0x023a00, "Medium not present" }, + { 0x025300, "Media load or eject failed" }, + { 0x025700, "Unable to recover table of contents" }, + { 0x030300, "Peripheral device write fault" }, + { 0x030301, "No write current" }, + { 0x030302, "Excessive write errors" }, + { 0x030c00, "Write error" }, + { 0x030c01, "Write error - Recovered with auto reallocation" }, + { 0x030c02, "Write error - auto reallocation failed" }, + { 0x030c03, "Write error - recommend reassignment" }, + { 0x030c04, "Compression check miscompare error" }, + { 0x030c05, "Data expansion occurred during compress" }, + { 0x030c06, "Block not compressible" }, + { 0x030c07, "Write error - recovery needed" }, + { 0x030c08, "Write error - recovery failed" }, + { 0x030c09, "Write error - loss of streaming" }, + { 0x031100, "Unrecovered read error" }, + { 0x031106, "CIRC unrecovered error" }, + { 0x033101, "Format command failed" }, + { 0x033200, "No defect spare location available" }, + { 0x033201, "Defect list update failure" }, + { 0x035100, "Erase failure" }, + { 0x037200, "Session fixation error" }, + { 0x037201, "Session fixation error writin lead-in" }, + { 0x037202, "Session fixation error writin lead-out" }, + { 0x037300, "CD control error" }, + { 0x037302, "Power calibration area is full" }, + { 0x037303, "Power calibration area error" }, + { 0x037304, "Program memory area / RMA update failure" }, + { 0x037305, "Program memory area / RMA is full" }, + { 0x037306, "Program memory area / RMA is (almost) full" }, + + { 0x040200, "No seek complete" }, + { 0x040300, "Write fault" }, + { 0x040900, "Track following error" }, + { 0x040901, "Tracking servo failure" }, + { 0x040902, "Focus servo failure" }, + { 0x040903, "Spindle servo failure" }, + { 0x041500, "Random positioning error" }, + { 0x041501, "Mechanical positioning or changer error" }, + { 0x041502, "Positioning error detected by read of medium" }, + { 0x043c00, "Mechanical positioning or changer error" }, + { 0x044000, "Diagnostic failure on component (ASCQ)" }, + { 0x044400, "Internal CD/DVD logical unit failure" }, + { 0x04b600, "Media load mechanism failed" }, + { 0x051a00, "Parameter list length error" }, + { 0x052000, "Invalid command operation code" }, + { 0x052100, "Logical block address out of range" }, + { 0x052102, "Invalid address for write" }, + { 0x052400, "Invalid field in command packet" }, + { 0x052600, "Invalid field in parameter list" }, + { 0x052601, "Parameter not supported" }, + { 0x052602, "Parameter value invalid" }, + { 0x052700, "Write protected media" }, + { 0x052c00, "Command sequence error" }, + { 0x052c03, "Current program area is not empty" }, + { 0x052c04, "Current program area is empty" }, + { 0x053001, "Cannot read medium - unknown format" }, + { 0x053002, "Cannot read medium - incompatible format" }, + { 0x053900, "Saving parameters not supported" }, + { 0x054e00, "Overlapped commands attempted" }, + { 0x055302, "Medium removal prevented" }, + { 0x055500, "System resource failure" }, + { 0x056300, "End of user area encountered on this track" }, + { 0x056400, "Illegal mode for this track or incompatible medium" }, + { 0x056f00, "Copy protection key exchange failure - Authentication failure" }, + { 0x056f01, "Copy protection key exchange failure - Key not present" }, + { 0x056f02, "Copy protection key exchange failure - Key not established" }, + { 0x056f03, "Read of scrambled sector without authentication" }, + { 0x056f04, "Media region code is mismatched to logical unit" }, + { 0x056f05, "Drive region must be permanent / region reset count error" }, + { 0x057203, "Session fixation error - incomplete track in session" }, + { 0x057204, "Empty or partially written reserved track" }, + { 0x057205, "No more RZONE reservations are allowed" }, + { 0x05bf00, "Loss of streaming" }, + { 0x062800, "Not ready to ready transition, medium may have changed" }, + { 0x062900, "Power on, reset or hardware reset occurred" }, + { 0x062a00, "Parameters changed" }, + { 0x062a01, "Mode parameters changed" }, + { 0x062e00, "Insufficient time for operation" }, + { 0x063f00, "Logical unit operating conditions have changed" }, + { 0x063f01, "Microcode has been changed" }, + { 0x065a00, "Operator request or state change input (unspecified)" }, + { 0x065a01, "Operator medium removal request" }, + { 0x0bb900, "Play operation aborted" }, + + /* Here we use 0xff for the key (not a valid key) to signify + * that these can have _any_ key value associated with them... */ + { 0xff0401, "Logical unit is in process of becoming ready" }, + { 0xff0400, "Logical unit not ready, cause not reportable" }, + { 0xff0402, "Logical unit not ready, initializing command required" }, + { 0xff0403, "Logical unit not ready, manual intervention required" }, + { 0xff0500, "Logical unit does not respond to selection" }, + { 0xff0800, "Logical unit communication failure" }, + { 0xff0802, "Logical unit communication parity error" }, + { 0xff0801, "Logical unit communication time-out" }, + { 0xff2500, "Logical unit not supported" }, + { 0xff4c00, "Logical unit failed self-configuration" }, + { 0xff3e00, "Logical unit has not self-configured yet" }, +}; +#endif + + +#endif /* _IDE_CD_H */ |