diff options
Diffstat (limited to 'drivers/ide/ide-tape.c')
| -rw-r--r-- | drivers/ide/ide-tape.c | 1679 |
1 files changed, 430 insertions, 1249 deletions
diff --git a/drivers/ide/ide-tape.c b/drivers/ide/ide-tape.c index 0598ecfd5f3..54a43b04460 100644 --- a/drivers/ide/ide-tape.c +++ b/drivers/ide/ide-tape.c @@ -72,26 +72,6 @@ enum { #endif /**************************** Tunable parameters *****************************/ - - -/* - * Pipelined mode parameters. - * - * We try to use the minimum number of stages which is enough to keep the tape - * constantly streaming. To accomplish that, we implement a feedback loop around - * the maximum number of stages: - * - * We start from MIN maximum stages (we will not even use MIN stages if we don't - * need them), increment it by RATE*(MAX-MIN) whenever we sense that the - * pipeline is empty, until we reach the optimum value or until we reach MAX. - * - * Setting the following parameter to 0 is illegal: the pipelined mode cannot be - * disabled (idetape_calculate_speeds() divides by tape->max_stages.) - */ -#define IDETAPE_MIN_PIPELINE_STAGES 1 -#define IDETAPE_MAX_PIPELINE_STAGES 400 -#define IDETAPE_INCREASE_STAGES_RATE 20 - /* * After each failed packet command we issue a request sense command and retry * the packet command IDETAPE_MAX_PC_RETRIES times. @@ -181,56 +161,59 @@ struct idetape_bh { char *b_data; }; -typedef struct idetape_packet_command_s { - /* Actual packet bytes */ - u8 c[12]; - /* On each retry, we increment retries */ - int retries; - /* Error code */ - int error; - /* Bytes to transfer */ - int request_transfer; - /* Bytes actually transferred */ - int actually_transferred; - /* Size of our data buffer */ - int buffer_size; - struct idetape_bh *bh; - char *b_data; - int b_count; - /* Data buffer */ - u8 *buffer; - /* Pointer into the above buffer */ - u8 *current_position; - /* Called when this packet command is completed */ - ide_startstop_t (*callback) (ide_drive_t *); - /* Temporary buffer */ - u8 pc_buffer[IDETAPE_PC_BUFFER_SIZE]; - /* Status/Action bit flags: long for set_bit */ - unsigned long flags; -} idetape_pc_t; +/* Tape door status */ +#define DOOR_UNLOCKED 0 +#define DOOR_LOCKED 1 +#define DOOR_EXPLICITLY_LOCKED 2 + +/* Some defines for the SPACE command */ +#define IDETAPE_SPACE_OVER_FILEMARK 1 +#define IDETAPE_SPACE_TO_EOD 3 + +/* Some defines for the LOAD UNLOAD command */ +#define IDETAPE_LU_LOAD_MASK 1 +#define IDETAPE_LU_RETENSION_MASK 2 +#define IDETAPE_LU_EOT_MASK 4 /* - * Packet command flag bits. + * Special requests for our block device strategy routine. + * + * In order to service a character device command, we add special requests to + * the tail of our block device request queue and wait for their completion. */ -/* Set when an error is considered normal - We won't retry */ -#define PC_ABORT 0 -/* 1 When polling for DSC on a media access command */ -#define PC_WAIT_FOR_DSC 1 -/* 1 when we prefer to use DMA if possible */ -#define PC_DMA_RECOMMENDED 2 -/* 1 while DMA in progress */ -#define PC_DMA_IN_PROGRESS 3 -/* 1 when encountered problem during DMA */ -#define PC_DMA_ERROR 4 -/* Data direction */ -#define PC_WRITING 5 - -/* A pipeline stage. */ -typedef struct idetape_stage_s { - struct request rq; /* The corresponding request */ - struct idetape_bh *bh; /* The data buffers */ - struct idetape_stage_s *next; /* Pointer to the next stage */ -} idetape_stage_t; + +enum { + REQ_IDETAPE_PC1 = (1 << 0), /* packet command (first stage) */ + REQ_IDETAPE_PC2 = (1 << 1), /* packet command (second stage) */ + REQ_IDETAPE_READ = (1 << 2), + REQ_IDETAPE_WRITE = (1 << 3), +}; + +/* Error codes returned in rq->errors to the higher part of the driver. */ +#define IDETAPE_ERROR_GENERAL 101 +#define IDETAPE_ERROR_FILEMARK 102 +#define IDETAPE_ERROR_EOD 103 + +/* Structures related to the SELECT SENSE / MODE SENSE packet commands. */ +#define IDETAPE_BLOCK_DESCRIPTOR 0 +#define IDETAPE_CAPABILITIES_PAGE 0x2a + +/* Tape flag bits values. */ +enum { + IDETAPE_FLAG_IGNORE_DSC = (1 << 0), + /* 0 When the tape position is unknown */ + IDETAPE_FLAG_ADDRESS_VALID = (1 << 1), + /* Device already opened */ + IDETAPE_FLAG_BUSY = (1 << 2), + /* Attempt to auto-detect the current user block size */ + IDETAPE_FLAG_DETECT_BS = (1 << 3), + /* Currently on a filemark */ + IDETAPE_FLAG_FILEMARK = (1 << 4), + /* DRQ interrupt device */ + IDETAPE_FLAG_DRQ_INTERRUPT = (1 << 5), + /* 0 = no tape is loaded, so we don't rewind after ejecting */ + IDETAPE_FLAG_MEDIUM_PRESENT = (1 << 6), +}; /* * Most of our global data which we need to save even as we leave the driver due @@ -258,11 +241,11 @@ typedef struct ide_tape_obj { * retry, to get detailed information on what went wrong. */ /* Current packet command */ - idetape_pc_t *pc; + struct ide_atapi_pc *pc; /* Last failed packet command */ - idetape_pc_t *failed_pc; + struct ide_atapi_pc *failed_pc; /* Packet command stack */ - idetape_pc_t pc_stack[IDETAPE_PC_STACK]; + struct ide_atapi_pc pc_stack[IDETAPE_PC_STACK]; /* Next free packet command storage space */ int pc_stack_index; struct request rq_stack[IDETAPE_PC_STACK]; @@ -275,9 +258,7 @@ typedef struct ide_tape_obj { * While polling for DSC we use postponed_rq to postpone the current * request so that ide.c will be able to service pending requests on the * other device. Note that at most we will have only one DSC (usually - * data transfer) request in the device request queue. Additional - * requests can be queued in our internal pipeline, but they will be - * visible to ide.c only one at a time. + * data transfer) request in the device request queue. */ struct request *postponed_rq; /* The time in which we started polling for DSC */ @@ -317,43 +298,20 @@ typedef struct ide_tape_obj { * At most, there is only one ide-tape originated data transfer request * in the device request queue. This allows ide.c to easily service * requests from the other device when we postpone our active request. - * In the pipelined operation mode, we use our internal pipeline - * structure to hold more data requests. The data buffer size is chosen - * based on the tape's recommendation. */ - /* ptr to the request which is waiting in the device request queue */ - struct request *active_data_rq; + /* Data buffer size chosen based on the tape's recommendation */ - int stage_size; - idetape_stage_t *merge_stage; - int merge_stage_size; + int buffer_size; + /* merge buffer */ + struct idetape_bh *merge_bh; + /* size of the merge buffer */ + int merge_bh_size; + /* pointer to current buffer head within the merge buffer */ struct idetape_bh *bh; char *b_data; int b_count; - /* - * Pipeline parameters. - * - * To accomplish non-pipelined mode, we simply set the following - * variables to zero (or NULL, where appropriate). - */ - /* Number of currently used stages */ - int nr_stages; - /* Number of pending stages */ - int nr_pending_stages; - /* We will not allocate more than this number of stages */ - int max_stages, min_pipeline, max_pipeline; - /* The first stage which will be removed from the pipeline */ - idetape_stage_t *first_stage; - /* The currently active stage */ - idetape_stage_t *active_stage; - /* Will be serviced after the currently active request */ - idetape_stage_t *next_stage; - /* New requests will be added to the pipeline here */ - idetape_stage_t *last_stage; - /* Optional free stage which we can use */ - idetape_stage_t *cache_stage; - int pages_per_stage; + int pages_per_buffer; /* Wasted space in each stage */ int excess_bh_size; @@ -374,45 +332,6 @@ typedef struct ide_tape_obj { /* the tape is write protected (hardware or opened as read-only) */ char write_prot; - /* - * Limit the number of times a request can be postponed, to avoid an - * infinite postpone deadlock. - */ - int postpone_cnt; - - /* - * Measures number of frames: - * - * 1. written/read to/from the driver pipeline (pipeline_head). - * 2. written/read to/from the tape buffers (idetape_bh). - * 3. written/read by the tape to/from the media (tape_head). - */ - int pipeline_head; - int buffer_head; - int tape_head; - int last_tape_head; - - /* Speed control at the tape buffers input/output */ - unsigned long insert_time; - int insert_size; - int insert_speed; - int max_insert_speed; - int measure_insert_time; - - /* Speed regulation negative feedback loop */ - int speed_control; - int pipeline_head_speed; - int controlled_pipeline_head_speed; - int uncontrolled_pipeline_head_speed; - int controlled_last_pipeline_head; - unsigned long uncontrolled_pipeline_head_time; - unsigned long controlled_pipeline_head_time; - int controlled_previous_pipeline_head; - int uncontrolled_previous_pipeline_head; - unsigned long controlled_previous_head_time; - unsigned long uncontrolled_previous_head_time; - int restart_speed_control_req; - u32 debug_mask; } idetape_tape_t; @@ -446,58 +365,6 @@ static void ide_tape_put(struct ide_tape_obj *tape) mutex_unlock(&idetape_ref_mutex); } -/* Tape door status */ -#define DOOR_UNLOCKED 0 -#define DOOR_LOCKED 1 -#define DOOR_EXPLICITLY_LOCKED 2 - -/* - * Tape flag bits values. - */ -#define IDETAPE_IGNORE_DSC 0 -#define IDETAPE_ADDRESS_VALID 1 /* 0 When the tape position is unknown */ -#define IDETAPE_BUSY 2 /* Device already opened */ -#define IDETAPE_PIPELINE_ERROR 3 /* Error detected in a pipeline stage */ -#define IDETAPE_DETECT_BS 4 /* Attempt to auto-detect the current user block size */ -#define IDETAPE_FILEMARK 5 /* Currently on a filemark */ -#define IDETAPE_DRQ_INTERRUPT 6 /* DRQ interrupt device */ -#define IDETAPE_READ_ERROR 7 -#define IDETAPE_PIPELINE_ACTIVE 8 /* pipeline active */ -/* 0 = no tape is loaded, so we don't rewind after ejecting */ -#define IDETAPE_MEDIUM_PRESENT 9 - -/* Some defines for the SPACE command */ -#define IDETAPE_SPACE_OVER_FILEMARK 1 -#define IDETAPE_SPACE_TO_EOD 3 - -/* Some defines for the LOAD UNLOAD command */ -#define IDETAPE_LU_LOAD_MASK 1 -#define IDETAPE_LU_RETENSION_MASK 2 -#define IDETAPE_LU_EOT_MASK 4 - -/* - * Special requests for our block device strategy routine. - * - * In order to service a character device command, we add special requests to - * the tail of our block device request queue and wait for their completion. - */ - -enum { - REQ_IDETAPE_PC1 = (1 << 0), /* packet command (first stage) */ - REQ_IDETAPE_PC2 = (1 << 1), /* packet command (second stage) */ - REQ_IDETAPE_READ = (1 << 2), - REQ_IDETAPE_WRITE = (1 << 3), -}; - -/* Error codes returned in rq->errors to the higher part of the driver. */ -#define IDETAPE_ERROR_GENERAL 101 -#define IDETAPE_ERROR_FILEMARK 102 -#define IDETAPE_ERROR_EOD 103 - -/* Structures related to the SELECT SENSE / MODE SENSE packet commands. */ -#define IDETAPE_BLOCK_DESCRIPTOR 0 -#define IDETAPE_CAPABILITIES_PAGE 0x2a - /* * The variables below are used for the character device interface. Additional * state variables are defined in our ide_drive_t structure. @@ -518,17 +385,7 @@ static struct ide_tape_obj *ide_tape_chrdev_get(unsigned int i) return tape; } -/* - * Too bad. The drive wants to send us data which we are not ready to accept. - * Just throw it away. - */ -static void idetape_discard_data(ide_drive_t *drive, unsigned int bcount) -{ - while (bcount--) - (void) HWIF(drive)->INB(IDE_DATA_REG); -} - -static void idetape_input_buffers(ide_drive_t *drive, idetape_pc_t *pc, +static void idetape_input_buffers(ide_drive_t *drive, struct ide_atapi_pc *pc, unsigned int bcount) { struct idetape_bh *bh = pc->bh; @@ -538,13 +395,13 @@ static void idetape_input_buffers(ide_drive_t *drive, idetape_pc_t *pc, if (bh == NULL) { printk(KERN_ERR "ide-tape: bh == NULL in " "idetape_input_buffers\n"); - idetape_discard_data(drive, bcount); + ide_pad_transfer(drive, 0, bcount); return; } count = min( (unsigned int)(bh->b_size - atomic_read(&bh->b_count)), bcount); - HWIF(drive)->atapi_input_bytes(drive, bh->b_data + + drive->hwif->input_data(drive, NULL, bh->b_data + atomic_read(&bh->b_count), count); bcount -= count; atomic_add(count, &bh->b_count); @@ -557,7 +414,7 @@ static void idetape_input_buffers(ide_drive_t *drive, idetape_pc_t *pc, pc->bh = bh; } -static void idetape_output_buffers(ide_drive_t *drive, idetape_pc_t *pc, +static void idetape_output_buffers(ide_drive_t *drive, struct ide_atapi_pc *pc, unsigned int bcount) { struct idetape_bh *bh = pc->bh; @@ -570,7 +427,7 @@ static void idetape_output_buffers(ide_drive_t *drive, idetape_pc_t *pc, return; } count = min((unsigned int)pc->b_count, (unsigned int)bcount); - HWIF(drive)->atapi_output_bytes(drive, pc->b_data, count); + drive->hwif->output_data(drive, NULL, pc->b_data, count); bcount -= count; pc->b_data += count; pc->b_count -= count; @@ -585,13 +442,13 @@ static void idetape_output_buffers(ide_drive_t *drive, idetape_pc_t *pc, } } -static void idetape_update_buffers(idetape_pc_t *pc) +static void idetape_update_buffers(struct ide_atapi_pc *pc) { struct idetape_bh *bh = pc->bh; int count; - unsigned int bcount = pc->actually_transferred; + unsigned int bcount = pc->xferred; - if (test_bit(PC_WRITING, &pc->flags)) + if (pc->flags & PC_FLAG_WRITING) return; while (bcount) { if (bh == NULL) { @@ -614,7 +471,7 @@ static void idetape_update_buffers(idetape_pc_t *pc) * driver. A storage space for a maximum of IDETAPE_PC_STACK packet * commands is allocated at initialization time. */ -static idetape_pc_t *idetape_next_pc_storage(ide_drive_t *drive) +static struct ide_atapi_pc *idetape_next_pc_storage(ide_drive_t *drive) { idetape_tape_t *tape = drive->driver_data; @@ -649,14 +506,14 @@ static struct request *idetape_next_rq_storage(ide_drive_t *drive) return (&tape->rq_stack[tape->rq_stack_index++]); } -static void idetape_init_pc(idetape_pc_t *pc) +static void idetape_init_pc(struct ide_atapi_pc *pc) { memset(pc->c, 0, 12); pc->retries = 0; pc->flags = 0; - pc->request_transfer = 0; - pc->buffer = pc->pc_buffer; - pc->buffer_size = IDETAPE_PC_BUFFER_SIZE; + pc->req_xfer = 0; + pc->buf = pc->pc_buf; + pc->buf_size = IDETAPE_PC_BUFFER_SIZE; pc->bh = NULL; pc->b_data = NULL; } @@ -668,7 +525,7 @@ static void idetape_init_pc(idetape_pc_t *pc) static void idetape_analyze_error(ide_drive_t *drive, u8 *sense) { idetape_tape_t *tape = drive->driver_data; - idetape_pc_t *pc = tape->failed_pc; + struct ide_atapi_pc *pc = tape->failed_pc; tape->sense_key = sense[2] & 0xF; tape->asc = sense[12]; @@ -677,9 +534,9 @@ static void idetape_analyze_error(ide_drive_t *drive, u8 *sense) debug_log(DBG_ERR, "pc = %x, sense key = %x, asc = %x, ascq = %x\n", pc->c[0], tape->sense_key, tape->asc, tape->ascq); - /* Correct pc->actually_transferred by asking the tape. */ - if (test_bit(PC_DMA_ERROR, &pc->flags)) { - pc->actually_transferred = pc->request_transfer - + /* Correct pc->xferred by asking the tape. */ + if (pc->flags & PC_FLAG_DMA_ERROR) { + pc->xferred = pc->req_xfer - tape->blk_size * be32_to_cpu(get_unaligned((u32 *)&sense[3])); idetape_update_buffers(pc); @@ -697,153 +554,61 @@ static void idetape_analyze_error(ide_drive_t *drive, u8 *sense) /* don't report an error, everything's ok */ pc->error = 0; /* don't retry read/write */ - set_bit(PC_ABORT, &pc->flags); + pc->flags |= PC_FLAG_ABORT; } } if (pc->c[0] == READ_6 && (sense[2] & 0x80)) { pc->error = IDETAPE_ERROR_FILEMARK; - set_bit(PC_ABORT, &pc->flags); + pc->flags |= PC_FLAG_ABORT; } if (pc->c[0] == WRITE_6) { if ((sense[2] & 0x40) || (tape->sense_key == 0xd && tape->asc == 0x0 && tape->ascq == 0x2)) { pc->error = IDETAPE_ERROR_EOD; - set_bit(PC_ABORT, &pc->flags); + pc->flags |= PC_FLAG_ABORT; } } if (pc->c[0] == READ_6 || pc->c[0] == WRITE_6) { if (tape->sense_key == 8) { pc->error = IDETAPE_ERROR_EOD; - set_bit(PC_ABORT, &pc->flags); + pc->flags |= PC_FLAG_ABORT; } - if (!test_bit(PC_ABORT, &pc->flags) && - pc->actually_transferred) + if (!(pc->flags & PC_FLAG_ABORT) && + pc->xferred) pc->retries = IDETAPE_MAX_PC_RETRIES + 1; } } -static void idetape_activate_next_stage(ide_drive_t *drive) +/* Free data buffers completely. */ +static void ide_tape_kfree_buffer(idetape_tape_t *tape) { - idetape_tape_t *tape = drive->driver_data; - idetape_stage_t *stage = tape->next_stage; - struct request *rq = &stage->rq; + struct idetape_bh *prev_bh, *bh = tape->merge_bh; - debug_log(DBG_PROCS, "Enter %s\n", __func__); + while (bh) { + u32 size = bh->b_size; - if (stage == NULL) { - printk(KERN_ERR "ide-tape: bug: Trying to activate a non" - " existing stage\n"); - return; - } + while (size) { + unsigned int order = fls(size >> PAGE_SHIFT)-1; - rq->rq_disk = tape->disk; - rq->buffer = NULL; - rq->special = (void *)stage->bh; - tape->active_data_rq = rq; - tape->active_stage = stage; - tape->next_stage = stage->next; -} - -/* Free a stage along with its related buffers completely. */ -static void __idetape_kfree_stage(idetape_stage_t *stage) -{ - struct idetape_bh *prev_bh, *bh = stage->bh; - int size; - - while (bh != NULL) { - if (bh->b_data != NULL) { - size = (int) bh->b_size; - while (size > 0) { - free_page((unsigned long) bh->b_data); - size -= PAGE_SIZE; - bh->b_data += PAGE_SIZE; - } + if (bh->b_data) + free_pages((unsigned long)bh->b_data, order); + + size &= (order-1); + bh->b_data += (1 << order) * PAGE_SIZE; } prev_bh = bh; bh = bh->b_reqnext; kfree(prev_bh); } - kfree(stage); -} - -static void idetape_kfree_stage(idetape_tape_t *tape, idetape_stage_t *stage) -{ - __idetape_kfree_stage(stage); -} - -/* - * Remove tape->first_stage from the pipeline. The caller should avoid race - * conditions. - */ -static void idetape_remove_stage_head(ide_drive_t *drive) -{ - idetape_tape_t *tape = drive->driver_data; - idetape_stage_t *stage; - - debug_log(DBG_PROCS, "Enter %s\n", __func__); - - if (tape->first_stage == NULL) { - printk(KERN_ERR "ide-tape: bug: tape->first_stage is NULL\n"); - return; - } - if (tape->active_stage == tape->first_stage) { - printk(KERN_ERR "ide-tape: bug: Trying to free our active " - "pipeline stage\n"); - return; - } - stage = tape->first_stage; - tape->first_stage = stage->next; - idetape_kfree_stage(tape, stage); - tape->nr_stages--; - if (tape->first_stage == NULL) { - tape->last_stage = NULL; - if (tape->next_stage != NULL) - printk(KERN_ERR "ide-tape: bug: tape->next_stage !=" - " NULL\n"); - if (tape->nr_stages) - printk(KERN_ERR "ide-tape: bug: nr_stages should be 0 " - "now\n"); - } -} - -/* - * This will free all the pipeline stages starting from new_last_stage->next - * to the end of the list, and point tape->last_stage to new_last_stage. - */ -static void idetape_abort_pipeline(ide_drive_t *drive, - idetape_stage_t *new_last_stage) -{ - idetape_tape_t *tape = drive->driver_data; - idetape_stage_t *stage = new_last_stage->next; - idetape_stage_t *nstage; - - debug_log(DBG_PROCS, "%s: Enter %s\n", tape->name, __func__); - - while (stage) { - nstage = stage->next; - idetape_kfree_stage(tape, stage); - --tape->nr_stages; - --tape->nr_pending_stages; - stage = nstage; - } - if (new_last_stage) - new_last_stage->next = NULL; - tape->last_stage = new_last_stage; - tape->next_stage = NULL; + kfree(tape->merge_bh); } -/* - * Finish servicing a request and insert a pending pipeline request into the - * main device queue. - */ static int idetape_end_request(ide_drive_t *drive, int uptodate, int nr_sects) { struct request *rq = HWGROUP(drive)->rq; idetape_tape_t *tape = drive->driver_data; unsigned long flags; int error; - int remove_stage = 0; - idetape_stage_t *active_stage; debug_log(DBG_PROCS, "Enter %s\n", __func__); @@ -863,56 +628,8 @@ static int idetape_end_request(ide_drive_t *drive, int uptodate, int nr_sects) spin_lock_irqsave(&tape->lock, flags); - /* The request was a pipelined data transfer request */ - if (tape->active_data_rq == rq) { - active_stage = tape->active_stage; - tape->active_stage = NULL; - tape->active_data_rq = NULL; - tape->nr_pending_stages--; - if (rq->cmd[0] & REQ_IDETAPE_WRITE) { - remove_stage = 1; - if (error) { - set_bit(IDETAPE_PIPELINE_ERROR, &tape->flags); - if (error == IDETAPE_ERROR_EOD) - idetape_abort_pipeline(drive, - active_stage); - } - } else if (rq->cmd[0] & REQ_IDETAPE_READ) { - if (error == IDETAPE_ERROR_EOD) { - set_bit(IDETAPE_PIPELINE_ERROR, &tape->flags); - idetape_abort_pipeline(drive, active_stage); - } - } - if (tape->next_stage != NULL) { - idetape_activate_next_stage(drive); - - /* Insert the next request into the request queue. */ - (void)ide_do_drive_cmd(drive, tape->active_data_rq, - ide_end); - } else if (!error) { - /* - * This is a part of the feedback loop which tries to - * find the optimum number of stages. We are starting - * from a minimum maximum number of stages, and if we - * sense that the pipeline is empty, we try to increase - * it, until we reach the user compile time memory - * limit. - */ - int i = (tape->max_pipeline - tape->min_pipeline) / 10; - - tape->max_stages += max(i, 1); - tape->max_stages = max(tape->max_stages, - tape->min_pipeline); - tape->max_stages = min(tape->max_stages, - tape->max_pipeline); - } - } ide_end_drive_cmd(drive, 0, 0); - if (remove_stage) - idetape_remove_stage_head(drive); - if (tape->active_data_rq == NULL) - clear_bit(IDETAPE_PIPELINE_ACTIVE, &tape->flags); spin_unlock_irqrestore(&tape->lock, flags); return 0; } @@ -924,7 +641,7 @@ static ide_startstop_t idetape_request_sense_callback(ide_drive_t *drive) debug_log(DBG_PROCS, "Enter %s\n", __func__); if (!tape->pc->error) { - idetape_analyze_error(drive, tape->pc->buffer); + idetape_analyze_error(drive, tape->pc->buf); idetape_end_request(drive, 1, 0); } else { printk(KERN_ERR "ide-tape: Error in REQUEST SENSE itself - " @@ -934,13 +651,13 @@ static ide_startstop_t idetape_request_sense_callback(ide_drive_t *drive) return ide_stopped; } -static void idetape_create_request_sense_cmd(idetape_pc_t *pc) +static void idetape_create_request_sense_cmd(struct ide_atapi_pc *pc) { idetape_init_pc(pc); pc->c[0] = REQUEST_SENSE; pc->c[4] = 20; - pc->request_transfer = 20; - pc->callback = &idetape_request_sense_callback; + pc->req_xfer = 20; + pc->idetape_callback = &idetape_request_sense_callback; } static void idetape_init_rq(struct request *rq, u8 cmd) @@ -965,7 +682,7 @@ static void idetape_init_rq(struct request *rq, u8 cmd) * handling functions should queue request to the lower level part and wait for * their completion using idetape_queue_pc_tail or idetape_queue_rw_tail. */ -static void idetape_queue_pc_head(ide_drive_t *drive, idetape_pc_t *pc, +static void idetape_queue_pc_head(ide_drive_t *drive, struct ide_atapi_pc *pc, struct request *rq) { struct ide_tape_obj *tape = drive->driver_data; @@ -984,14 +701,14 @@ static void idetape_queue_pc_head(ide_drive_t *drive, idetape_pc_t *pc, static ide_startstop_t idetape_retry_pc (ide_drive_t *drive) { idetape_tape_t *tape = drive->driver_data; - idetape_pc_t *pc; + struct ide_atapi_pc *pc; struct request *rq; (void)ide_read_error(drive); pc = idetape_next_pc_storage(drive); rq = idetape_next_rq_storage(drive); idetape_create_request_sense_cmd(pc); - set_bit(IDETAPE_IGNORE_DSC, &tape->flags); + set_bit(IDETAPE_FLAG_IGNORE_DSC, &tape->flags); idetape_queue_pc_head(drive, pc, rq); return ide_stopped; } @@ -1010,7 +727,7 @@ static void idetape_postpone_request(ide_drive_t *drive) ide_stall_queue(drive, tape->dsc_poll_freq); } -typedef void idetape_io_buf(ide_drive_t *, idetape_pc_t *, unsigned int); +typedef void idetape_io_buf(ide_drive_t *, struct ide_atapi_pc *, unsigned int); /* * This is the usual interrupt handler which will be called during a packet @@ -1023,7 +740,7 @@ static ide_startstop_t idetape_pc_intr(ide_drive_t *drive) { ide_hwif_t *hwif = drive->hwif; idetape_tape_t *tape = drive->driver_data; - idetape_pc_t *pc = tape->pc; + struct ide_atapi_pc *pc = tape->pc; xfer_func_t *xferfunc; idetape_io_buf *iobuf; unsigned int temp; @@ -1038,8 +755,8 @@ static ide_startstop_t idetape_pc_intr(ide_drive_t *drive) /* Clear the interrupt */ stat = ide_read_status(drive); - if (test_bit(PC_DMA_IN_PROGRESS, &pc->flags)) { - if (hwif->ide_dma_end(drive) || (stat & ERR_STAT)) { + if (pc->flags & PC_FLAG_DMA_IN_PROGRESS) { + if (hwif->dma_ops->dma_end(drive) || (stat & ERR_STAT)) { /* * A DMA error is sometimes expected. For example, * if the tape is crossing a filemark during a @@ -1061,9 +778,9 @@ static ide_startstop_t idetape_pc_intr(ide_drive_t *drive) * data transfer will occur, but no DMA error. * (AS, 19 Apr 2001) */ - set_bit(PC_DMA_ERROR, &pc->flags); + pc->flags |= PC_FLAG_DMA_ERROR; } else { - pc->actually_transferred = pc->request_transfer; + pc->xferred = pc->req_xfer; idetape_update_buffers(pc); } debug_log(DBG_PROCS, "DMA finished\n"); @@ -1073,9 +790,9 @@ static ide_startstop_t idetape_pc_intr(ide_drive_t *drive) /* No more interrupts */ if ((stat & DRQ_STAT) == 0) { debug_log(DBG_SENSE, "Packet command completed, %d bytes" - " transferred\n", pc->actually_transferred); + " transferred\n", pc->xferred); - clear_bit(PC_DMA_IN_PROGRESS, &pc->flags); + pc->flags &= ~PC_FLAG_DMA_IN_PROGRESS; local_irq_enable(); #if SIMULATE_ERRORS @@ -1088,7 +805,7 @@ static ide_startstop_t idetape_pc_intr(ide_drive_t *drive) #endif if ((stat & ERR_STAT) && pc->c[0] == REQUEST_SENSE) stat &= ~ERR_STAT; - if ((stat & ERR_STAT) || test_bit(PC_DMA_ERROR, &pc->flags)) { + if ((stat & ERR_STAT) || (pc->flags & PC_FLAG_DMA_ERROR)) { /* Error detected */ debug_log(DBG_ERR, "%s: I/O error\n", tape->name); @@ -1104,7 +821,7 @@ static ide_startstop_t idetape_pc_intr(ide_drive_t *drive) return idetape_retry_pc(drive); } pc->error = 0; - if (test_bit(PC_WAIT_FOR_DSC, &pc->flags) && + if ((pc->flags & PC_FLAG_WAIT_FOR_DSC) && (stat & SEEK_STAT) == 0) { /* Media access command */ tape->dsc_polling_start = jiffies; @@ -1117,9 +834,11 @@ static ide_startstop_t idetape_pc_intr(ide_drive_t *drive) if (tape->failed_pc == pc) tape->failed_pc = NULL; /* Command finished - Call the callback function */ - return pc->callback(drive); + return pc->idetape_callback(drive); } - if (test_and_clear_bit(PC_DMA_IN_PROGRESS, &pc->flags)) { + + if (pc->flags & PC_FLAG_DMA_IN_PROGRESS) { + pc->flags &= ~PC_FLAG_DMA_IN_PROGRESS; printk(KERN_ERR "ide-tape: The tape wants to issue more " "interrupts in DMA mode\n"); printk(KERN_ERR "ide-tape: DMA disabled, reverting to PIO\n"); @@ -1127,16 +846,16 @@ static ide_startstop_t idetape_pc_intr(ide_drive_t *drive) return ide_do_reset(drive); } /* Get the number of bytes to transfer on this interrupt. */ - bcount = (hwif->INB(IDE_BCOUNTH_REG) << 8) | - hwif->INB(IDE_BCOUNTL_REG); + bcount = (hwif->INB(hwif->io_ports.lbah_addr) << 8) | + hwif->INB(hwif->io_ports.lbam_addr); - ireason = hwif->INB(IDE_IREASON_REG); + ireason = hwif->INB(hwif->io_ports.nsect_addr); if (ireason & CD) { printk(KERN_ERR "ide-tape: CoD != 0 in %s\n", __func__); return ide_do_reset(drive); } - if (((ireason & IO) == IO) == test_bit(PC_WRITING, &pc->flags)) { + if (((ireason & IO) == IO) == !!(pc->flags & PC_FLAG_WRITING)) { /* Hopefully, we will never get here */ printk(KERN_ERR "ide-tape: We wanted to %s, ", (ireason & IO) ? "Write" : "Read"); @@ -1144,15 +863,15 @@ static ide_startstop_t idetape_pc_intr(ide_drive_t *drive) (ireason & IO) ? "Read" : "Write"); return ide_do_reset(drive); } - if (!test_bit(PC_WRITING, &pc->flags)) { + if (!(pc->flags & PC_FLAG_WRITING)) { /* Reading - Check that we have enough space */ - temp = pc->actually_transferred + bcount; - if (temp > pc->request_transfer) { - if (temp > pc->buffer_size) { + temp = pc->xferred + bcount; + if (temp > pc->req_xfer) { + if (temp > pc->buf_size) { printk(KERN_ERR "ide-tape: The tape wants to " "send us more data than expected " "- discarding data\n"); - idetape_discard_data(drive, bcount); + ide_pad_transfer(drive, 0, bcount); ide_set_handler(drive, &idetape_pc_intr, IDETAPE_WAIT_CMD, NULL); return ide_started; @@ -1161,20 +880,20 @@ static ide_startstop_t idetape_pc_intr(ide_drive_t *drive) "data than expected - allowing transfer\n"); } iobuf = &idetape_input_buffers; - xferfunc = hwif->atapi_input_bytes; + xferfunc = hwif->input_data; } else { iobuf = &idetape_output_buffers; - xferfunc = hwif->atapi_output_bytes; + xferfunc = hwif->output_data; } if (pc->bh) iobuf(drive, pc, bcount); else - xferfunc(drive, pc->current_position, bcount); + xferfunc(drive, NULL, pc->cur_pos, bcount); /* Update the current position */ - pc->actually_transferred += bcount; - pc->current_position += bcount; + pc->xferred += bcount; + pc->cur_pos += bcount; debug_log(DBG_SENSE, "[cmd %x] transferred %d bytes on that intr.\n", pc->c[0], bcount); @@ -1224,7 +943,7 @@ static ide_startstop_t idetape_transfer_pc(ide_drive_t *drive) { ide_hwif_t *hwif = drive->hwif; idetape_tape_t *tape = drive->driver_data; - idetape_pc_t *pc = tape->pc; + struct ide_atapi_pc *pc = tape->pc; int retries = 100; ide_startstop_t startstop; u8 ireason; @@ -1234,12 +953,12 @@ static ide_startstop_t idetape_transfer_pc(ide_drive_t *drive) "yet DRQ isn't asserted\n"); return startstop; } - ireason = hwif->INB(IDE_IREASON_REG); + ireason = hwif->INB(hwif->io_ports.nsect_addr); while (retries-- && ((ireason & CD) == 0 || (ireason & IO))) { printk(KERN_ERR "ide-tape: (IO,CoD != (0,1) while issuing " "a packet command, retrying\n"); udelay(100); - ireason = hwif->INB(IDE_IREASON_REG); + ireason = hwif->INB(hwif->io_ports.nsect_addr); if (retries == 0) { printk(KERN_ERR "ide-tape: (IO,CoD != (0,1) while " "issuing a packet command, ignoring\n"); @@ -1256,15 +975,17 @@ static ide_startstop_t idetape_transfer_pc(ide_drive_t *drive) ide_set_handler(drive, &idetape_pc_intr, IDETAPE_WAIT_CMD, NULL); #ifdef CONFIG_BLK_DEV_IDEDMA /* Begin DMA, if necessary */ - if (test_bit(PC_DMA_IN_PROGRESS, &pc->flags)) - hwif->dma_start(drive); + if (pc->flags & PC_FLAG_DMA_IN_PROGRESS) + hwif->dma_ops->dma_start(drive); #endif /* Send the actual packet */ - HWIF(drive)->atapi_output_bytes(drive, pc->c, 12); + hwif->output_data(drive, NULL, pc->c, 12); + return ide_started; } -static ide_startstop_t idetape_issue_pc(ide_drive_t *drive, idetape_pc_t *pc) +static ide_startstop_t idetape_issue_pc(ide_drive_t *drive, + struct ide_atapi_pc *pc) { ide_hwif_t *hwif = drive->hwif; idetape_tape_t *tape = drive->driver_data; @@ -1283,13 +1004,13 @@ static ide_startstop_t idetape_issue_pc(ide_drive_t *drive, idetape_pc_t *pc) tape->pc = pc; if (pc->retries > IDETAPE_MAX_PC_RETRIES || - test_bit(PC_ABORT, &pc->flags)) { + (pc->flags & PC_FLAG_ABORT)) { /* * We will "abort" retrying a packet command in case legitimate * error code was received (crossing a filemark, or end of the * media, for example). */ - if (!test_bit(PC_ABORT, &pc->flags)) { + if (!(pc->flags & PC_FLAG_ABORT)) { if (!(pc->c[0] == TEST_UNIT_READY && tape->sense_key == 2 && tape->asc == 4 && (tape->ascq == 1 || tape->ascq == 8))) { @@ -1304,36 +1025,38 @@ static ide_startstop_t idetape_issue_pc(ide_drive_t *drive, idetape_pc_t *pc) pc->error = IDETAPE_ERROR_GENERAL; } tape->failed_pc = NULL; - return pc->callback(drive); + return pc->idetape_callback(drive); } debug_log(DBG_SENSE, "Retry #%d, cmd = %02X\n", pc->retries, pc->c[0]); pc->retries++; /* We haven't transferred any data yet */ - pc->actually_transferred = 0; - pc->current_position = pc->buffer; + pc->xferred = 0; + pc->cur_pos = pc->buf; /* Request to transfer the entire buffer at once */ - bcount = pc->request_transfer; + bcount = pc->req_xfer; - if (test_and_clear_bit(PC_DMA_ERROR, &pc->flags)) { + if (pc->flags & PC_FLAG_DMA_ERROR) { + pc->flags &= ~PC_FLAG_DMA_ERROR; printk(KERN_WARNING "ide-tape: DMA disabled, " "reverting to PIO\n"); ide_dma_off(drive); } - if (test_bit(PC_DMA_RECOMMENDED, &pc->flags) && drive->using_dma) - dma_ok = !hwif->dma_setup(drive); + if ((pc->flags & PC_FLAG_DMA_RECOMMENDED) && drive->using_dma) + dma_ok = !hwif->dma_ops->dma_setup(drive); ide_pktcmd_tf_load(drive, IDE_TFLAG_NO_SELECT_MASK | IDE_TFLAG_OUT_DEVICE, bcount, dma_ok); - if (dma_ok) /* Will begin DMA later */ - set_bit(PC_DMA_IN_PROGRESS, &pc->flags); - if (test_bit(IDETAPE_DRQ_INTERRUPT, &tape->flags)) { + if (dma_ok) + /* Will begin DMA later */ + pc->flags |= PC_FLAG_DMA_IN_PROGRESS; + if (test_bit(IDETAPE_FLAG_DRQ_INTERRUPT, &tape->flags)) { ide_execute_command(drive, WIN_PACKETCMD, &idetape_transfer_pc, IDETAPE_WAIT_CMD, NULL); return ide_started; } else { - hwif->OUTB(WIN_PACKETCMD, IDE_COMMAND_REG); + ide_execute_pkt_cmd(drive); return idetape_transfer_pc(drive); } } @@ -1349,7 +1072,7 @@ static ide_startstop_t idetape_pc_callback(ide_drive_t *drive) } /* A mode sense command is used to "sense" tape parameters. */ -static void idetape_create_mode_sense_cmd(idetape_pc_t *pc, u8 page_code) +static void idetape_create_mode_sense_cmd(struct ide_atapi_pc *pc, u8 page_code) { idetape_init_pc(pc); pc->c[0] = MODE_SENSE; @@ -1368,81 +1091,18 @@ static void idetape_create_mode_sense_cmd(idetape_pc_t *pc, u8 page_code) /* We will just discard data in that case */ pc->c[4] = 255; if (page_code == IDETAPE_BLOCK_DESCRIPTOR) - pc->request_transfer = 12; + pc->req_xfer = 12; else if (page_code == IDETAPE_CAPABILITIES_PAGE) - pc->request_transfer = 24; + pc->req_xfer = 24; else - pc->request_transfer = 50; - pc->callback = &idetape_pc_callback; -} - -static void idetape_calculate_speeds(ide_drive_t *drive) -{ - idetape_tape_t *tape = drive->driver_data; - - if (time_after(jiffies, - tape->controlled_pipeline_head_time + 120 * HZ)) { - tape->controlled_previous_pipeline_head = - tape->controlled_last_pipeline_head; - tape->controlled_previous_head_time = - tape->controlled_pipeline_head_time; - tape->controlled_last_pipeline_head = tape->pipeline_head; - tape->controlled_pipeline_head_time = jiffies; - } - if (time_after(jiffies, tape->controlled_pipeline_head_time + 60 * HZ)) - tape->controlled_pipeline_head_speed = (tape->pipeline_head - - tape->controlled_last_pipeline_head) * 32 * HZ / - (jiffies - tape->controlled_pipeline_head_time); - else if (time_after(jiffies, tape->controlled_previous_head_time)) - tape->controlled_pipeline_head_speed = (tape->pipeline_head - - tape->controlled_previous_pipeline_head) * 32 * - HZ / (jiffies - tape->controlled_previous_head_time); - - if (tape->nr_pending_stages < tape->max_stages/*- 1 */) { - /* -1 for read mode error recovery */ - if (time_after(jiffies, tape->uncontrolled_previous_head_time + - 10 * HZ)) { - tape->uncontrolled_pipeline_head_time = jiffies; - tape->uncontrolled_pipeline_head_speed = - (tape->pipeline_head - - tape->uncontrolled_previous_pipeline_head) * - 32 * HZ / (jiffies - - tape->uncontrolled_previous_head_time); - } - } else { - tape->uncontrolled_previous_head_time = jiffies; - tape->uncontrolled_previous_pipeline_head = tape->pipeline_head; - if (time_after(jiffies, tape->uncontrolled_pipeline_head_time + - 30 * HZ)) - tape->uncontrolled_pipeline_head_time = jiffies; - - } - tape->pipeline_head_speed = max(tape->uncontrolled_pipeline_head_speed, - tape->controlled_pipeline_head_speed); - - if (tape->speed_control == 1) { - if (tape->nr_pending_stages >= tape->max_stages / 2) - tape->max_insert_speed = tape->pipeline_head_speed + - (1100 - tape->pipeline_head_speed) * 2 * - (tape->nr_pending_stages - tape->max_stages / 2) - / tape->max_stages; - else - tape->max_insert_speed = 500 + - (tape->pipeline_head_speed - 500) * 2 * - tape->nr_pending_stages / tape->max_stages; - - if (tape->nr_pending_stages >= tape->max_stages * 99 / 100) - tape->max_insert_speed = 5000; - } else - tape->max_insert_speed = tape->speed_control; - - tape->max_insert_speed = max(tape->max_insert_speed, 500); + pc->req_xfer = 50; + pc->idetape_callback = &idetape_pc_callback; } static ide_startstop_t idetape_media_access_finished(ide_drive_t *drive) { idetape_tape_t *tape = drive->driver_data; - idetape_pc_t *pc = tape->pc; + struct ide_atapi_pc *pc = tape->pc; u8 stat; stat = ide_read_status(drive); @@ -1463,27 +1123,17 @@ static ide_startstop_t idetape_media_access_finished(ide_drive_t *drive) pc->error = IDETAPE_ERROR_GENERAL; tape->failed_pc = NULL; } - return pc->callback(drive); + return pc->idetape_callback(drive); } static ide_startstop_t idetape_rw_callback(ide_drive_t *drive) { idetape_tape_t *tape = drive->driver_data; struct request *rq = HWGROUP(drive)->rq; - int blocks = tape->pc->actually_transferred / tape->blk_size; + int blocks = tape->pc->xferred / tape->blk_size; tape->avg_size += blocks * tape->blk_size; - tape->insert_size += blocks * tape->blk_size; - if (tape->insert_size > 1024 * 1024) - tape->measure_insert_time = 1; - if (tape->measure_insert_time) { - tape->measure_insert_time = 0; - tape->insert_time = jiffies; - tape->insert_size = 0; - } - if (time_after(jiffies, tape->insert_time)) - tape->insert_speed = tape->insert_size / 1024 * HZ / - (jiffies - tape->insert_time); + if (time_after_eq(jiffies, tape->avg_time + HZ)) { tape->avg_speed = tape->avg_size * HZ / (jiffies - tape->avg_time) / 1024; @@ -1502,47 +1152,49 @@ static ide_startstop_t idetape_rw_callback(ide_drive_t *drive) return ide_stopped; } -static void idetape_create_read_cmd(idetape_tape_t *tape, idetape_pc_t *pc, +static void idetape_create_read_cmd(idetape_tape_t *tape, + struct ide_atapi_pc *pc, unsigned int length, struct idetape_bh *bh) { idetape_init_pc(pc); pc->c[0] = READ_6; put_unaligned(cpu_to_be32(length), (unsigned int *) &pc->c[1]); pc->c[1] = 1; - pc->callback = &idetape_rw_callback; + pc->idetape_callback = &idetape_rw_callback; pc->bh = bh; atomic_set(&bh->b_count, 0); - pc->buffer = NULL; - pc->buffer_size = length * tape->blk_size; - pc->request_transfer = pc->buffer_size; - if (pc->request_transfer == tape->stage_size) - set_bit(PC_DMA_RECOMMENDED, &pc->flags); + pc->buf = NULL; + pc->buf_size = length * tape->blk_size; + pc->req_xfer = pc->buf_size; + if (pc->req_xfer == tape->buffer_size) + pc->flags |= PC_FLAG_DMA_RECOMMENDED; } -static void idetape_create_write_cmd(idetape_tape_t *tape, idetape_pc_t *pc, +static void idetape_create_write_cmd(idetape_tape_t *tape, + struct ide_atapi_pc *pc, unsigned int length, struct idetape_bh *bh) { idetape_init_pc(pc); pc->c[0] = WRITE_6; put_unaligned(cpu_to_be32(length), (unsigned int *) &pc->c[1]); pc->c[1] = 1; - pc->callback = &idetape_rw_callback; - set_bit(PC_WRITING, &pc->flags); + pc->idetape_callback = &idetape_rw_callback; + pc->flags |= PC_FLAG_WRITING; pc->bh = bh; pc->b_data = bh->b_data; pc->b_count = atomic_read(&bh->b_count); - pc->buffer = NULL; - pc->buffer_size = length * tape->blk_size; - pc->request_transfer = pc->buffer_size; - if (pc->request_transfer == tape->stage_size) - set_bit(PC_DMA_RECOMMENDED, &pc->flags); + pc->buf = NULL; + pc->buf_size = length * tape->blk_size; + pc->req_xfer = pc->buf_size; + if (pc->req_xfer == tape->buffer_size) + pc->flags |= PC_FLAG_DMA_RECOMMENDED; } static ide_startstop_t idetape_do_request(ide_drive_t *drive, struct request *rq, sector_t block) { idetape_tape_t *tape = drive->driver_data; - idetape_pc_t *pc = NULL; + struct ide_atapi_pc *pc = NULL; struct request *postponed_rq = tape->postponed_rq; u8 stat; @@ -1579,18 +1231,14 @@ static ide_startstop_t idetape_do_request(ide_drive_t *drive, stat = ide_read_status(drive); if (!drive->dsc_overlap && !(rq->cmd[0] & REQ_IDETAPE_PC2)) - set_bit(IDETAPE_IGNORE_DSC, &tape->flags); + set_bit(IDETAPE_FLAG_IGNORE_DSC, &tape->flags); if (drive->post_reset == 1) { - set_bit(IDETAPE_IGNORE_DSC, &tape->flags); + set_bit(IDETAPE_FLAG_IGNORE_DSC, &tape->flags); drive->post_reset = 0; } - if (time_after(jiffies, tape->insert_time)) - tape->insert_speed = tape->insert_size / 1024 * HZ / - (jiffies - tape->insert_time); - idetape_calculate_speeds(drive); - if (!test_and_clear_bit(IDETAPE_IGNORE_DSC, &tape->flags) && + if (!test_and_clear_bit(IDETAPE_FLAG_IGNORE_DSC, &tape->flags) && (stat & SEEK_STAT) == 0) { if (postponed_rq == NULL) { tape->dsc_polling_start = jiffies; @@ -1613,23 +1261,19 @@ static ide_startstop_t idetape_do_request(ide_drive_t *drive, return ide_stopped; } if (rq->cmd[0] & REQ_IDETAPE_READ) { - tape->buffer_head++; - tape->postpone_cnt = 0; pc = idetape_next_pc_storage(drive); idetape_create_read_cmd(tape, pc, rq->current_nr_sectors, (struct idetape_bh *)rq->special); goto out; } if (rq->cmd[0] & REQ_IDETAPE_WRITE) { - tape->buffer_head++; - tape->postpone_cnt = 0; pc = idetape_next_pc_storage(drive); idetape_create_write_cmd(tape, pc, rq->current_nr_sectors, (struct idetape_bh *)rq->special); goto out; } if (rq->cmd[0] & REQ_IDETAPE_PC1) { - pc = (idetape_pc_t *) rq->buffer; + pc = (struct ide_atapi_pc *) rq->buffer; rq->cmd[0] &= ~(REQ_IDETAPE_PC1); rq->cmd[0] |= REQ_IDETAPE_PC2; goto out; @@ -1643,111 +1287,91 @@ out: return idetape_issue_pc(drive, pc); } -/* Pipeline related functions */ -static inline int idetape_pipeline_active(idetape_tape_t *tape) -{ - int rc1, rc2; - - rc1 = test_bit(IDETAPE_PIPELINE_ACTIVE, &tape->flags); - rc2 = (tape->active_data_rq != NULL); - return rc1; -} - /* - * The function below uses __get_free_page to allocate a pipeline stage, along - * with all the necessary small buffers which together make a buffer of size - * tape->stage_size (or a bit more). We attempt to combine sequential pages as + * The function below uses __get_free_pages to allocate a data buffer of size + * tape->buffer_size (or a bit more). We attempt to combine sequential pages as * much as possible. * - * It returns a pointer to the new allocated stage, or NULL if we can't (or - * don't want to) allocate a stage. - * - * Pipeline stages are optional and are used to increase performance. If we - * can't allocate them, we'll manage without them. + * It returns a pointer to the newly allocated buffer, or NULL in case of + * failure. */ -static idetape_stage_t *__idetape_kmalloc_stage(idetape_tape_t *tape, int full, - int clear) +static struct idetape_bh *ide_tape_kmalloc_buffer(idetape_tape_t *tape, + int full, int clear) { - idetape_stage_t *stage; - struct idetape_bh *prev_bh, *bh; - int pages = tape->pages_per_stage; + struct idetape_bh *prev_bh, *bh, *merge_bh; + int pages = tape->pages_per_buffer; + unsigned int order, b_allocd; char *b_data = NULL; - stage = kmalloc(sizeof(idetape_stage_t), GFP_KERNEL); - if (!stage) - return NULL; - stage->next = NULL; - - stage->bh = kmalloc(sizeof(struct idetape_bh), GFP_KERNEL); - bh = stage->bh; + merge_bh = kmalloc(sizeof(struct idetape_bh), GFP_KERNEL); + bh = merge_bh; if (bh == NULL) goto abort; - bh->b_reqnext = NULL; - bh->b_data = (char *) __get_free_page(GFP_KERNEL); + + order = fls(pages) - 1; + bh->b_data = (char *) __get_free_pages(GFP_KERNEL, order); if (!bh->b_data) goto abort; + b_allocd = (1 << order) * PAGE_SIZE; + pages &= (order-1); + if (clear) - memset(bh->b_data, 0, PAGE_SIZE); - bh->b_size = PAGE_SIZE; + memset(bh->b_data, 0, b_allocd); + bh->b_reqnext = NULL; + bh->b_size = b_allocd; atomic_set(&bh->b_count, full ? bh->b_size : 0); - while (--pages) { - b_data = (char *) __get_free_page(GFP_KERNEL); + while (pages) { + order = fls(pages) - 1; + b_data = (char *) __get_free_pages(GFP_KERNEL, order); if (!b_data) goto abort; + b_allocd = (1 << order) * PAGE_SIZE; + if (clear) - memset(b_data, 0, PAGE_SIZE); - if (bh->b_data == b_data + PAGE_SIZE) { - bh->b_size += PAGE_SIZE; - bh->b_data -= PAGE_SIZE; + memset(b_data, 0, b_allocd); + + /* newly allocated page frames below buffer header or ...*/ + if (bh->b_data == b_data + b_allocd) { + bh->b_size += b_allocd; + bh->b_data -= b_allocd; if (full) - atomic_add(PAGE_SIZE, &bh->b_count); + atomic_add(b_allocd, &bh->b_count); continue; } + /* they are above the header */ if (b_data == bh->b_data + bh->b_size) { - bh->b_size += PAGE_SIZE; + bh->b_size += b_allocd; if (full) - atomic_add(PAGE_SIZE, &bh->b_count); + atomic_add(b_allocd, &bh->b_count); continue; } prev_bh = bh; bh = kmalloc(sizeof(struct idetape_bh), GFP_KERNEL); if (!bh) { - free_page((unsigned long) b_data); + free_pages((unsigned long) b_data, order); goto abort; } bh->b_reqnext = NULL; bh->b_data = b_data; - bh->b_size = PAGE_SIZE; + bh->b_size = b_allocd; atomic_set(&bh->b_count, full ? bh->b_size : 0); prev_bh->b_reqnext = bh; + + pages &= (order-1); } + bh->b_size -= tape->excess_bh_size; if (full) atomic_sub(tape->excess_bh_size, &bh->b_count); - return stage; + return merge_bh; abort: - __idetape_kfree_stage(stage); + ide_tape_kfree_buffer(tape); return NULL; } -static idetape_stage_t *idetape_kmalloc_stage(idetape_tape_t *tape) -{ - idetape_stage_t *cache_stage = tape->cache_stage; - - debug_log(DBG_PROCS, "Enter %s\n", __func__); - - if (tape->nr_stages >= tape->max_stages) - return NULL; - if (cache_stage != NULL) { - tape->cache_stage = NULL; - return cache_stage; - } - return __idetape_kmalloc_stage(tape, 0, 0); -} - static int idetape_copy_stage_from_user(idetape_tape_t *tape, - idetape_stage_t *stage, const char __user *buf, int n) + const char __user *buf, int n) { struct idetape_bh *bh = tape->bh; int count; @@ -1779,7 +1403,7 @@ static int idetape_copy_stage_from_user(idetape_tape_t *tape, } static int idetape_copy_stage_to_user(idetape_tape_t *tape, char __user *buf, - idetape_stage_t *stage, int n) + int n) { struct idetape_bh *bh = tape->bh; int count; @@ -1810,11 +1434,11 @@ static int idetape_copy_stage_to_user(idetape_tape_t *tape, char __user *buf, return ret; } -static void idetape_init_merge_stage(idetape_tape_t *tape) +static void idetape_init_merge_buffer(idetape_tape_t *tape) { - struct idetape_bh *bh = tape->merge_stage->bh; + struct idetape_bh *bh = tape->merge_bh; + tape->bh = tape->merge_bh; - tape->bh = bh; if (tape->chrdev_dir == IDETAPE_DIR_WRITE) atomic_set(&bh->b_count, 0); else { @@ -1823,65 +1447,10 @@ static void idetape_init_merge_stage(idetape_tape_t *tape) } } -static void idetape_switch_buffers(idetape_tape_t *tape, idetape_stage_t *stage) -{ - struct idetape_bh *tmp; - - tmp = stage->bh; - stage->bh = tape->merge_stage->bh; - tape->merge_stage->bh = tmp; - idetape_init_merge_stage(tape); -} - -/* Add a new stage at the end of the pipeline. */ -static void idetape_add_stage_tail(ide_drive_t *drive, idetape_stage_t *stage) -{ - idetape_tape_t *tape = drive->driver_data; - unsigned long flags; - - debug_log(DBG_PROCS, "Enter %s\n", __func__); - - spin_lock_irqsave(&tape->lock, flags); - stage->next = NULL; - if (tape->last_stage != NULL) - tape->last_stage->next = stage; - else - tape->first_stage = stage; - tape->next_stage = stage; - tape->last_stage = stage; - if (tape->next_stage == NULL) - tape->next_stage = tape->last_stage; - tape->nr_stages++; - tape->nr_pending_stages++; - spin_unlock_irqrestore(&tape->lock, flags); -} - -/* Install a completion in a pending request and sleep until it is serviced. The - * caller should ensure that the request will not be serviced before we install - * the completion (usually by disabling interrupts). - */ -static void idetape_wait_for_request(ide_drive_t *drive, struct request *rq) -{ - DECLARE_COMPLETION_ONSTACK(wait); - idetape_tape_t *tape = drive->driver_data; - - if (rq == NULL || !blk_special_request(rq)) { - printk(KERN_ERR "ide-tape: bug: Trying to sleep on non-valid" - " request\n"); - return; - } - rq->end_io_data = &wait; - rq->end_io = blk_end_sync_rq; - spin_unlock_irq(&tape->lock); - wait_for_completion(&wait); - /* The stage and its struct request have been deallocated */ - spin_lock_irq(&tape->lock); -} - static ide_startstop_t idetape_read_position_callback(ide_drive_t *drive) { idetape_tape_t *tape = drive->driver_data; - u8 *readpos = tape->pc->buffer; + u8 *readpos = tape->pc->buf; debug_log(DBG_PROCS, "Enter %s\n", __func__); @@ -1894,7 +1463,7 @@ static ide_startstop_t idetape_read_position_callback(ide_drive_t *drive) if (readpos[0] & 0x4) { printk(KERN_INFO "ide-tape: Block location is unknown" "to the tape\n"); - clear_bit(IDETAPE_ADDRESS_VALID, &tape->flags); + clear_bit(IDETAPE_FLAG_ADDRESS_VALID, &tape->flags); idetape_end_request(drive, 0, 0); } else { debug_log(DBG_SENSE, "Block Location - %u\n", @@ -1903,7 +1472,7 @@ static ide_startstop_t idetape_read_position_callback(ide_drive_t *drive) tape->partition = readpos[1]; tape->first_frame = be32_to_cpu(*(u32 *)&readpos[4]); - set_bit(IDETAPE_ADDRESS_VALID, &tape->flags); + set_bit(IDETAPE_FLAG_ADDRESS_VALID, &tape->flags); idetape_end_request(drive, 1, 0); } } else { @@ -1917,20 +1486,20 @@ static ide_startstop_t idetape_read_position_callback(ide_drive_t *drive) * writing a filemark otherwise. */ static void idetape_create_write_filemark_cmd(ide_drive_t *drive, - idetape_pc_t *pc, int write_filemark) + struct ide_atapi_pc *pc, int write_filemark) { idetape_init_pc(pc); pc->c[0] = WRITE_FILEMARKS; pc->c[4] = write_filemark; - set_bit(PC_WAIT_FOR_DSC, &pc->flags); - pc->callback = &idetape_pc_callback; + pc->flags |= PC_FLAG_WAIT_FOR_DSC; + pc->idetape_callback = &idetape_pc_callback; } -static void idetape_create_test_unit_ready_cmd(idetape_pc_t *pc) +static void idetape_create_test_unit_ready_cmd(struct ide_atapi_pc *pc) { idetape_init_pc(pc); pc->c[0] = TEST_UNIT_READY; - pc->callback = &idetape_pc_callback; + pc->idetape_callback = &idetape_pc_callback; } /* @@ -1946,7 +1515,7 @@ static void idetape_create_test_unit_ready_cmd(idetape_pc_t *pc) * to the request list without waiting for it to be serviced! In that case, we * usually use idetape_queue_pc_head(). */ -static int __idetape_queue_pc_tail(ide_drive_t *drive, idetape_pc_t *pc) +static int idetape_queue_pc_tail(ide_drive_t *drive, struct ide_atapi_pc *pc) { struct ide_tape_obj *tape = drive->driver_data; struct request rq; @@ -1957,28 +1526,28 @@ static int __idetape_queue_pc_tail(ide_drive_t *drive, idetape_pc_t *pc) return ide_do_drive_cmd(drive, &rq, ide_wait); } -static void idetape_create_load_unload_cmd(ide_drive_t *drive, idetape_pc_t *pc, - int cmd) +static void idetape_create_load_unload_cmd(ide_drive_t *drive, + struct ide_atapi_pc *pc, int cmd) { idetape_init_pc(pc); pc->c[0] = START_STOP; pc->c[4] = cmd; - set_bit(PC_WAIT_FOR_DSC, &pc->flags); - pc->callback = &idetape_pc_callback; + pc->flags |= PC_FLAG_WAIT_FOR_DSC; + pc->idetape_callback = &idetape_pc_callback; } static int idetape_wait_ready(ide_drive_t *drive, unsigned long timeout) { idetape_tape_t *tape = drive->driver_data; - idetape_pc_t pc; + struct ide_atapi_pc pc; int load_attempted = 0; /* Wait for the tape to become ready */ - set_bit(IDETAPE_MEDIUM_PRESENT, &tape->flags); + set_bit(IDETAPE_FLAG_MEDIUM_PRESENT, &tape->flags); timeout += jiffies; while (time_before(jiffies, timeout)) { idetape_create_test_unit_ready_cmd(&pc); - if (!__idetape_queue_pc_tail(drive, &pc)) + if (!idetape_queue_pc_tail(drive, &pc)) return 0; if ((tape->sense_key == 2 && tape->asc == 4 && tape->ascq == 2) || (tape->asc == 0x3A)) { @@ -1987,7 +1556,7 @@ static int idetape_wait_ready(ide_drive_t *drive, unsigned long timeout) return -ENOMEDIUM; idetape_create_load_unload_cmd(drive, &pc, IDETAPE_LU_LOAD_MASK); - __idetape_queue_pc_tail(drive, &pc); + idetape_queue_pc_tail(drive, &pc); load_attempted = 1; /* not about to be ready */ } else if (!(tape->sense_key == 2 && tape->asc == 4 && @@ -1998,14 +1567,9 @@ static int idetape_wait_ready(ide_drive_t *drive, unsigned long timeout) return -EIO; } -static int idetape_queue_pc_tail(ide_drive_t *drive, idetape_pc_t *pc) -{ - return __idetape_queue_pc_tail(drive, pc); -} - static int idetape_flush_tape_buffers(ide_drive_t *drive) { - idetape_pc_t pc; + struct ide_atapi_pc pc; int rc; idetape_create_write_filemark_cmd(drive, &pc, 0); @@ -2016,18 +1580,18 @@ static int idetape_flush_tape_buffers(ide_drive_t *drive) return 0; } -static void idetape_create_read_position_cmd(idetape_pc_t *pc) +static void idetape_create_read_position_cmd(struct ide_atapi_pc *pc) { idetape_init_pc(pc); pc->c[0] = READ_POSITION; - pc->request_transfer = 20; - pc->callback = &idetape_read_position_callback; + pc->req_xfer = 20; + pc->idetape_callback = &idetape_read_position_callback; } static int idetape_read_position(ide_drive_t *drive) { idetape_tape_t *tape = drive->driver_data; - idetape_pc_t pc; + struct ide_atapi_pc pc; int position; debug_log(DBG_PROCS, "Enter %s\n", __func__); @@ -2039,7 +1603,8 @@ static int idetape_read_position(ide_drive_t *drive) return position; } -static void idetape_create_locate_cmd(ide_drive_t *drive, idetape_pc_t *pc, +static void idetape_create_locate_cmd(ide_drive_t *drive, + struct ide_atapi_pc *pc, unsigned int block, u8 partition, int skip) { idetape_init_pc(pc); @@ -2047,12 +1612,12 @@ static void idetape_create_locate_cmd(ide_drive_t *drive, idetape_pc_t *pc, pc->c[1] = 2; put_unaligned(cpu_to_be32(block), (unsigned int *) &pc->c[3]); pc->c[8] = partition; - set_bit(PC_WAIT_FOR_DSC, &pc->flags); - pc->callback = &idetape_pc_callback; + pc->flags |= PC_FLAG_WAIT_FOR_DSC; + pc->idetape_callback = &idetape_pc_callback; } -static int idetape_create_prevent_cmd(ide_drive_t *drive, idetape_pc_t *pc, - int prevent) +static int idetape_create_prevent_cmd(ide_drive_t *drive, + struct ide_atapi_pc *pc, int prevent) { idetape_tape_t *tape = drive->driver_data; @@ -2063,54 +1628,25 @@ static int idetape_create_prevent_cmd(ide_drive_t *drive, idetape_pc_t *pc, idetape_init_pc(pc); pc->c[0] = ALLOW_MEDIUM_REMOVAL; pc->c[4] = prevent; - pc->callback = &idetape_pc_callback; + pc->idetape_callback = &idetape_pc_callback; return 1; } -static int __idetape_discard_read_pipeline(ide_drive_t *drive) +static void __ide_tape_discard_merge_buffer(ide_drive_t *drive) { idetape_tape_t *tape = drive->driver_data; - unsigned long flags; - int cnt; if (tape->chrdev_dir != IDETAPE_DIR_READ) - return 0; + return; - /* Remove merge stage. */ - cnt = tape->merge_stage_size / tape->blk_size; - if (test_and_clear_bit(IDETAPE_FILEMARK, &tape->flags)) - ++cnt; /* Filemarks count as 1 sector */ - tape->merge_stage_size = 0; - if (tape->merge_stage != NULL) { - __idetape_kfree_stage(tape->merge_stage); - tape->merge_stage = NULL; + clear_bit(IDETAPE_FLAG_FILEMARK, &tape->flags); + tape->merge_bh_size = 0; + if (tape->merge_bh != NULL) { + ide_tape_kfree_buffer(tape); + tape->merge_bh = NULL; } - /* Clear pipeline flags. */ - clear_bit(IDETAPE_PIPELINE_ERROR, &tape->flags); tape->chrdev_dir = IDETAPE_DIR_NONE; - - /* Remove pipeline stages. */ - if (tape->first_stage == NULL) - return 0; - - spin_lock_irqsave(&tape->lock, flags); - tape->next_stage = NULL; - if (idetape_pipeline_active(tape)) - idetape_wait_for_request(drive, tape->active_data_rq); - spin_unlock_irqrestore(&tape->lock, flags); - - while (tape->first_stage != NULL) { - struct request *rq_ptr = &tape->first_stage->rq; - - cnt += rq_ptr->nr_sectors - rq_ptr->current_nr_sectors; - if (rq_ptr->errors == IDETAPE_ERROR_FILEMARK) - ++cnt; - idetape_remove_stage_head(drive); - } - tape->nr_pending_stages = 0; - tape->max_stages = tape->min_pipeline; - return cnt; } /* @@ -2124,10 +1660,10 @@ static int idetape_position_tape(ide_drive_t *drive, unsigned int block, { idetape_tape_t *tape = drive->driver_data; int retval; - idetape_pc_t pc; + struct ide_atapi_pc pc; if (tape->chrdev_dir == IDETAPE_DIR_READ) - __idetape_discard_read_pipeline(drive); + __ide_tape_discard_merge_buffer(drive); idetape_wait_ready(drive, 60 * 5 * HZ); idetape_create_locate_cmd(drive, &pc, block, partition, skip); retval = idetape_queue_pc_tail(drive, &pc); @@ -2138,20 +1674,19 @@ static int idetape_position_tape(ide_drive_t *drive, unsigned int block, return (idetape_queue_pc_tail(drive, &pc)); } -static void idetape_discard_read_pipeline(ide_drive_t *drive, +static void ide_tape_discard_merge_buffer(ide_drive_t *drive, int restore_position) { idetape_tape_t *tape = drive->driver_data; - int cnt; int seek, position; - cnt = __idetape_discard_read_pipeline(drive); + __ide_tape_discard_merge_buffer(drive); if (restore_position) { position = idetape_read_position(drive); - seek = position > cnt ? position - cnt : 0; + seek = position > 0 ? position : 0; if (idetape_position_tape(drive, seek, 0, 0)) { printk(KERN_INFO "ide-tape: %s: position_tape failed in" - " discard_pipeline()\n", tape->name); + " %s\n", tape->name, __func__); return; } } @@ -2169,12 +1704,6 @@ static int idetape_queue_rw_tail(ide_drive_t *drive, int cmd, int blocks, debug_log(DBG_SENSE, "%s: cmd=%d\n", __func__, cmd); - if (idetape_pipeline_active(tape)) { - printk(KERN_ERR "ide-tape: bug: the pipeline is active in %s\n", - __func__); - return (0); - } - idetape_init_rq(&rq, cmd); rq.rq_disk = tape->disk; rq.special = (void *)bh; @@ -2186,192 +1715,83 @@ static int idetape_queue_rw_tail(ide_drive_t *drive, int cmd, int blocks, if ((cmd & (REQ_IDETAPE_READ | REQ_IDETAPE_WRITE)) == 0) return 0; - if (tape->merge_stage) - idetape_init_merge_stage(tape); + if (tape->merge_bh) + idetape_init_merge_buffer(tape); if (rq.errors == IDETAPE_ERROR_GENERAL) return -EIO; return (tape->blk_size * (blocks-rq.current_nr_sectors)); } -/* start servicing the pipeline stages, starting from tape->next_stage. */ -static void idetape_plug_pipeline(ide_drive_t *drive) -{ - idetape_tape_t *tape = drive->driver_data; - - if (tape->next_stage == NULL) - return; - if (!idetape_pipeline_active(tape)) { - set_bit(IDETAPE_PIPELINE_ACTIVE, &tape->flags); - idetape_activate_next_stage(drive); - (void) ide_do_drive_cmd(drive, tape->active_data_rq, ide_end); - } -} - -static void idetape_create_inquiry_cmd(idetape_pc_t *pc) +static void idetape_create_inquiry_cmd(struct ide_atapi_pc *pc) { idetape_init_pc(pc); pc->c[0] = INQUIRY; pc->c[4] = 254; - pc->request_transfer = 254; - pc->callback = &idetape_pc_callback; + pc->req_xfer = 254; + pc->idetape_callback = &idetape_pc_callback; } -static void idetape_create_rewind_cmd(ide_drive_t *drive, idetape_pc_t *pc) +static void idetape_create_rewind_cmd(ide_drive_t *drive, + struct ide_atapi_pc *pc) { idetape_init_pc(pc); pc->c[0] = REZERO_UNIT; - set_bit(PC_WAIT_FOR_DSC, &pc->flags); - pc->callback = &idetape_pc_callback; + pc->flags |= PC_FLAG_WAIT_FOR_DSC; + pc->idetape_callback = &idetape_pc_callback; } -static void idetape_create_erase_cmd(idetape_pc_t *pc) +static void idetape_create_erase_cmd(struct ide_atapi_pc *pc) { idetape_init_pc(pc); pc->c[0] = ERASE; pc->c[1] = 1; - set_bit(PC_WAIT_FOR_DSC, &pc->flags); - pc->callback = &idetape_pc_callback; + pc->flags |= PC_FLAG_WAIT_FOR_DSC; + pc->idetape_callback = &idetape_pc_callback; } -static void idetape_create_space_cmd(idetape_pc_t *pc, int count, u8 cmd) +static void idetape_create_space_cmd(struct ide_atapi_pc *pc, int count, u8 cmd) { idetape_init_pc(pc); pc->c[0] = SPACE; put_unaligned(cpu_to_be32(count), (unsigned int *) &pc->c[1]); pc->c[1] = cmd; - set_bit(PC_WAIT_FOR_DSC, &pc->flags); - pc->callback = &idetape_pc_callback; + pc->flags |= PC_FLAG_WAIT_FOR_DSC; + pc->idetape_callback = &idetape_pc_callback; } -static void idetape_wait_first_stage(ide_drive_t *drive) -{ - idetape_tape_t *tape = drive->driver_data; - unsigned long flags; - - if (tape->first_stage == NULL) - return; - spin_lock_irqsave(&tape->lock, flags); - if (tape->active_stage == tape->first_stage) - idetape_wait_for_request(drive, tape->active_data_rq); - spin_unlock_irqrestore(&tape->lock, flags); -} - -/* - * Try to add a character device originated write request to our pipeline. In - * case we don't succeed, we revert to non-pipelined operation mode for this - * request. In order to accomplish that, we - * - * 1. Try to allocate a new pipeline stage. - * 2. If we can't, wait for more and more requests to be serviced and try again - * each time. - * 3. If we still can't allocate a stage, fallback to non-pipelined operation - * mode for this request. - */ +/* Queue up a character device originated write request. */ static int idetape_add_chrdev_write_request(ide_drive_t *drive, int blocks) { idetape_tape_t *tape = drive->driver_data; - idetape_stage_t *new_stage; - unsigned long flags; - struct request *rq; debug_log(DBG_CHRDEV, "Enter %s\n", __func__); - /* Attempt to allocate a new stage. Beware possible race conditions. */ - while ((new_stage = idetape_kmalloc_stage(tape)) == NULL) { - spin_lock_irqsave(&tape->lock, flags); - if (idetape_pipeline_active(tape)) { - idetape_wait_for_request(drive, tape->active_data_rq); - spin_unlock_irqrestore(&tape->lock, flags); - } else { - spin_unlock_irqrestore(&tape->lock, flags); - idetape_plug_pipeline(drive); - if (idetape_pipeline_active(tape)) - continue; - /* - * The machine is short on memory. Fallback to non- - * pipelined operation mode for this request. - */ - return idetape_queue_rw_tail(drive, REQ_IDETAPE_WRITE, - blocks, tape->merge_stage->bh); - } - } - rq = &new_stage->rq; - idetape_init_rq(rq, REQ_IDETAPE_WRITE); - /* Doesn't actually matter - We always assume sequential access */ - rq->sector = tape->first_frame; - rq->current_nr_sectors = blocks; - rq->nr_sectors = blocks; - - idetape_switch_buffers(tape, new_stage); - idetape_add_stage_tail(drive, new_stage); - tape->pipeline_head++; - idetape_calculate_speeds(drive); - - /* - * Estimate whether the tape has stopped writing by checking if our - * write pipeline is currently empty. If we are not writing anymore, - * wait for the pipeline to be almost completely full (90%) before - * starting to service requests, so that we will be able to keep up with - * the higher speeds of the tape. - */ - if (!idetape_pipeline_active(tape)) { - if (tape->nr_stages >= tape->max_stages * 9 / 10 || - tape->nr_stages >= tape->max_stages - - tape->uncontrolled_pipeline_head_speed * 3 * 1024 / - tape->blk_size) { - tape->measure_insert_time = 1; - tape->insert_time = jiffies; - tape->insert_size = 0; - tape->insert_speed = 0; - idetape_plug_pipeline(drive); - } - } - if (test_and_clear_bit(IDETAPE_PIPELINE_ERROR, &tape->flags)) - /* Return a deferred error */ - return -EIO; - return blocks; + return idetape_queue_rw_tail(drive, REQ_IDETAPE_WRITE, + blocks, tape->merge_bh); } -/* - * Wait until all pending pipeline requests are serviced. Typically called on - * device close. - */ -static void idetape_wait_for_pipeline(ide_drive_t *drive) -{ - idetape_tape_t *tape = drive->driver_data; - unsigned long flags; - - while (tape->next_stage || idetape_pipeline_active(tape)) { - idetape_plug_pipeline(drive); - spin_lock_irqsave(&tape->lock, flags); - if (idetape_pipeline_active(tape)) - idetape_wait_for_request(drive, tape->active_data_rq); - spin_unlock_irqrestore(&tape->lock, flags); - } -} - -static void idetape_empty_write_pipeline(ide_drive_t *drive) +static void ide_tape_flush_merge_buffer(ide_drive_t *drive) { idetape_tape_t *tape = drive->driver_data; int blocks, min; struct idetape_bh *bh; if (tape->chrdev_dir != IDETAPE_DIR_WRITE) { - printk(KERN_ERR "ide-tape: bug: Trying to empty write pipeline," + printk(KERN_ERR "ide-tape: bug: Trying to empty merge buffer" " but we are not writing.\n"); return; } - if (tape->merge_stage_size > tape->stage_size) { + if (tape->merge_bh_size > tape->buffer_size) { printk(KERN_ERR "ide-tape: bug: merge_buffer too big\n"); - tape->merge_stage_size = tape->stage_size; + tape->merge_bh_size = tape->buffer_size; } - if (tape->merge_stage_size) { - blocks = tape->merge_stage_size / tape->blk_size; - if (tape->merge_stage_size % tape->blk_size) { + if (tape->merge_bh_size) { + blocks = tape->merge_bh_size / tape->blk_size; + if (tape->merge_bh_size % tape->blk_size) { unsigned int i; blocks++; - i = tape->blk_size - tape->merge_stage_size % + i = tape->blk_size - tape->merge_bh_size % tape->blk_size; bh = tape->bh->b_reqnext; while (bh) { @@ -2395,74 +1815,33 @@ static void idetape_empty_write_pipeline(ide_drive_t *drive) } } (void) idetape_add_chrdev_write_request(drive, blocks); - tape->merge_stage_size = 0; + tape->merge_bh_size = 0; } - idetape_wait_for_pipeline(drive); - if (tape->merge_stage != NULL) { - __idetape_kfree_stage(tape->merge_stage); - tape->merge_stage = NULL; + if (tape->merge_bh != NULL) { + ide_tape_kfree_buffer(tape); + tape->merge_bh = NULL; } - clear_bit(IDETAPE_PIPELINE_ERROR, &tape->flags); tape->chrdev_dir = IDETAPE_DIR_NONE; - - /* - * On the next backup, perform the feedback loop again. (I don't want to - * keep sense information between backups, as some systems are - * constantly on, and the system load can be totally different on the - * next backup). - */ - tape->max_stages = tape->min_pipeline; - if (tape->first_stage != NULL || - tape->next_stage != NULL || - tape->last_stage != NULL || - tape->nr_stages != 0) { - printk(KERN_ERR "ide-tape: ide-tape pipeline bug, " - "first_stage %p, next_stage %p, " - "last_stage %p, nr_stages %d\n", - tape->first_stage, tape->next_stage, - tape->last_stage, tape->nr_stages); - } } -static void idetape_restart_speed_control(ide_drive_t *drive) +static int idetape_init_read(ide_drive_t *drive) { idetape_tape_t *tape = drive->driver_data; - - tape->restart_speed_control_req = 0; - tape->pipeline_head = 0; - tape->controlled_last_pipeline_head = 0; - tape->controlled_previous_pipeline_head = 0; - tape->uncontrolled_previous_pipeline_head = 0; - tape->controlled_pipeline_head_speed = 5000; - tape->pipeline_head_speed = 5000; - tape->uncontrolled_pipeline_head_speed = 0; - tape->controlled_pipeline_head_time = - tape->uncontrolled_pipeline_head_time = jiffies; - tape->controlled_previous_head_time = - tape->uncontrolled_previous_head_time = jiffies; -} - -static int idetape_init_read(ide_drive_t *drive, int max_stages) -{ - idetape_tape_t *tape = drive->driver_data; - idetape_stage_t *new_stage; - struct request rq; int bytes_read; - u16 blocks = *(u16 *)&tape->caps[12]; /* Initialize read operation */ if (tape->chrdev_dir != IDETAPE_DIR_READ) { if (tape->chrdev_dir == IDETAPE_DIR_WRITE) { - idetape_empty_write_pipeline(drive); + ide_tape_flush_merge_buffer(drive); idetape_flush_tape_buffers(drive); } - if (tape->merge_stage || tape->merge_stage_size) { - printk(KERN_ERR "ide-tape: merge_stage_size should be" + if (tape->merge_bh || tape->merge_bh_size) { + printk(KERN_ERR "ide-tape: merge_bh_size should be" " 0 now\n"); - tape->merge_stage_size = 0; + tape->merge_bh_size = 0; } - tape->merge_stage = __idetape_kmalloc_stage(tape, 0, 0); - if (!tape->merge_stage) + tape->merge_bh = ide_tape_kmalloc_buffer(tape, 0, 0); + if (!tape->merge_bh) return -ENOMEM; tape->chrdev_dir = IDETAPE_DIR_READ; @@ -2475,94 +1854,34 @@ static int idetape_init_read(ide_drive_t *drive, int max_stages) if (drive->dsc_overlap) { bytes_read = idetape_queue_rw_tail(drive, REQ_IDETAPE_READ, 0, - tape->merge_stage->bh); + tape->merge_bh); if (bytes_read < 0) { - __idetape_kfree_stage(tape->merge_stage); - tape->merge_stage = NULL; + ide_tape_kfree_buffer(tape); + tape->merge_bh = NULL; tape->chrdev_dir = IDETAPE_DIR_NONE; return bytes_read; } } } - if (tape->restart_speed_control_req) - idetape_restart_speed_control(drive); - idetape_init_rq(&rq, REQ_IDETAPE_READ); - rq.sector = tape->first_frame; - rq.nr_sectors = blocks; - rq.current_nr_sectors = blocks; - if (!test_bit(IDETAPE_PIPELINE_ERROR, &tape->flags) && - tape->nr_stages < max_stages) { - new_stage = idetape_kmalloc_stage(tape); - while (new_stage != NULL) { - new_stage->rq = rq; - idetape_add_stage_tail(drive, new_stage); - if (tape->nr_stages >= max_stages) - break; - new_stage = idetape_kmalloc_stage(tape); - } - } - if (!idetape_pipeline_active(tape)) { - if (tape->nr_pending_stages >= 3 * max_stages / 4) { - tape->measure_insert_time = 1; - tape->insert_time = jiffies; - tape->insert_size = 0; - tape->insert_speed = 0; - idetape_plug_pipeline(drive); - } - } + return 0; } -/* - * Called from idetape_chrdev_read() to service a character device read request - * and add read-ahead requests to our pipeline. - */ +/* called from idetape_chrdev_read() to service a chrdev read request. */ static int idetape_add_chrdev_read_request(ide_drive_t *drive, int blocks) { idetape_tape_t *tape = drive->driver_data; - unsigned long flags; - struct request *rq_ptr; - int bytes_read; debug_log(DBG_PROCS, "Enter %s, %d blocks\n", __func__, blocks); /* If we are at a filemark, return a read length of 0 */ - if (test_bit(IDETAPE_FILEMARK, &tape->flags)) + if (test_bit(IDETAPE_FLAG_FILEMARK, &tape->flags)) return 0; - /* Wait for the next block to reach the head of the pipeline. */ - idetape_init_read(drive, tape->max_stages); - if (tape->first_stage == NULL) { - if (test_bit(IDETAPE_PIPELINE_ERROR, &tape->flags)) - return 0; - return idetape_queue_rw_tail(drive, REQ_IDETAPE_READ, blocks, - tape->merge_stage->bh); - } - idetape_wait_first_stage(drive); - rq_ptr = &tape->first_stage->rq; - bytes_read = tape->blk_size * (rq_ptr->nr_sectors - - rq_ptr->current_nr_sectors); - rq_ptr->nr_sectors = 0; - rq_ptr->current_nr_sectors = 0; + idetape_init_read(drive); - if (rq_ptr->errors == IDETAPE_ERROR_EOD) - return 0; - else { - idetape_switch_buffers(tape, tape->first_stage); - if (rq_ptr->errors == IDETAPE_ERROR_FILEMARK) - set_bit(IDETAPE_FILEMARK, &tape->flags); - spin_lock_irqsave(&tape->lock, flags); - idetape_remove_stage_head(drive); - spin_unlock_irqrestore(&tape->lock, flags); - tape->pipeline_head++; - idetape_calculate_speeds(drive); - } - if (bytes_read > blocks * tape->blk_size) { - printk(KERN_ERR "ide-tape: bug: trying to return more bytes" - " than requested\n"); - bytes_read = blocks * tape->blk_size; - } - return (bytes_read); + return idetape_queue_rw_tail(drive, REQ_IDETAPE_READ, blocks, + tape->merge_bh); } static void idetape_pad_zeros(ide_drive_t *drive, int bcount) @@ -2574,8 +1893,8 @@ static void idetape_pad_zeros(ide_drive_t *drive, int bcount) while (bcount) { unsigned int count; - bh = tape->merge_stage->bh; - count = min(tape->stage_size, bcount); + bh = tape->merge_bh; + count = min(tape->buffer_size, bcount); bcount -= count; blocks = count / tape->blk_size; while (count) { @@ -2586,29 +1905,8 @@ static void idetape_pad_zeros(ide_drive_t *drive, int bcount) bh = bh->b_reqnext; } idetape_queue_rw_tail(drive, REQ_IDETAPE_WRITE, blocks, - tape->merge_stage->bh); - } -} - -static int idetape_pipeline_size(ide_drive_t *drive) -{ - idetape_tape_t *tape = drive->driver_data; - idetape_stage_t *stage; - struct request *rq; - int size = 0; - - idetape_wait_for_pipeline(drive); - stage = tape->first_stage; - while (stage != NULL) { - rq = &stage->rq; - size += tape->blk_size * (rq->nr_sectors - - rq->current_nr_sectors); - if (rq->errors == IDETAPE_ERROR_FILEMARK) - size += tape->blk_size; - stage = stage->next; + tape->merge_bh); } - size += tape->merge_stage_size; - return size; } /* @@ -2618,7 +1916,7 @@ static int idetape_pipeline_size(ide_drive_t *drive) static int idetape_rewind_tape(ide_drive_t *drive) { int retval; - idetape_pc_t pc; + struct ide_atapi_pc pc; idetape_tape_t *tape; tape = drive->driver_data; @@ -2656,11 +1954,10 @@ static int idetape_blkdev_ioctl(ide_drive_t *drive, unsigned int cmd, if (copy_from_user(&config, argp, sizeof(config))) return -EFAULT; tape->best_dsc_rw_freq = config.dsc_rw_frequency; - tape->max_stages = config.nr_stages; break; case 0x0350: config.dsc_rw_frequency = (int) tape->best_dsc_rw_freq; - config.nr_stages = tape->max_stages; + config.nr_stages = 1; if (copy_to_user(argp, &config, sizeof(config))) return -EFAULT; break; @@ -2670,19 +1967,11 @@ static int idetape_blkdev_ioctl(ide_drive_t *drive, unsigned int cmd, return 0; } -/* - * The function below is now a bit more complicated than just passing the - * command to the tape since we may have crossed some filemarks during our - * pipelined read-ahead mode. As a minor side effect, the pipeline enables us to - * support MTFSFM when the filemark is in our internal pipeline even if the tape - * doesn't support spacing over filemarks in the reverse direction. - */ static int idetape_space_over_filemarks(ide_drive_t *drive, short mt_op, int mt_count) { idetape_tape_t *tape = drive->driver_data; - idetape_pc_t pc; - unsigned long flags; + struct ide_atapi_pc pc; int retval, count = 0; int sprev = !!(tape->caps[4] & 0x20); @@ -2695,47 +1984,12 @@ static int idetape_space_over_filemarks(ide_drive_t *drive, short mt_op, } if (tape->chrdev_dir == IDETAPE_DIR_READ) { - /* its a read-ahead buffer, scan it for crossed filemarks. */ - tape->merge_stage_size = 0; - if (test_and_clear_bit(IDETAPE_FILEMARK, &tape->flags)) + tape->merge_bh_size = 0; + if (test_and_clear_bit(IDETAPE_FLAG_FILEMARK, &tape->flags)) ++count; - while (tape->first_stage != NULL) { - if (count == mt_count) { - if (mt_op == MTFSFM) - set_bit(IDETAPE_FILEMARK, &tape->flags); - return 0; - } - spin_lock_irqsave(&tape->lock, flags); - if (tape->first_stage == tape->active_stage) { - /* - * We have reached the active stage in the read - * pipeline. There is no point in allowing the - * drive to continue reading any farther, so we - * stop the pipeline. - * - * This section should be moved to a separate - * subroutine because similar operations are - * done in __idetape_discard_read_pipeline(), - * for example. - */ - tape->next_stage = NULL; - spin_unlock_irqrestore(&tape->lock, flags); - idetape_wait_first_stage(drive); - tape->next_stage = tape->first_stage->next; - } else - spin_unlock_irqrestore(&tape->lock, flags); - if (tape->first_stage->rq.errors == - IDETAPE_ERROR_FILEMARK) - ++count; - idetape_remove_stage_head(drive); - } - idetape_discard_read_pipeline(drive, 0); + ide_tape_discard_merge_buffer(drive, 0); } - /* - * The filemark was not found in our internal pipeline; now we can issue - * the space command. - */ switch (mt_op) { case MTFSF: case MTBSF: @@ -2786,32 +2040,30 @@ static ssize_t idetape_chrdev_read(struct file *file, char __user *buf, debug_log(DBG_CHRDEV, "Enter %s, count %Zd\n", __func__, count); if (tape->chrdev_dir != IDETAPE_DIR_READ) { - if (test_bit(IDETAPE_DETECT_BS, &tape->flags)) + if (test_bit(IDETAPE_FLAG_DETECT_BS, &tape->flags)) if (count > tape->blk_size && (count % tape->blk_size) == 0) tape->user_bs_factor = count / tape->blk_size; } - rc = idetape_init_read(drive, tape->max_stages); + rc = idetape_init_read(drive); if (rc < 0) return rc; if (count == 0) return (0); - if (tape->merge_stage_size) { - actually_read = min((unsigned int)(tape->merge_stage_size), + if (tape->merge_bh_size) { + actually_read = min((unsigned int)(tape->merge_bh_size), (unsigned int)count); - if (idetape_copy_stage_to_user(tape, buf, tape->merge_stage, - actually_read)) + if (idetape_copy_stage_to_user(tape, buf, actually_read)) ret = -EFAULT; buf += actually_read; - tape->merge_stage_size -= actually_read; + tape->merge_bh_size -= actually_read; count -= actually_read; } - while (count >= tape->stage_size) { + while (count >= tape->buffer_size) { bytes_read = idetape_add_chrdev_read_request(drive, ctl); if (bytes_read <= 0) goto finish; - if (idetape_copy_stage_to_user(tape, buf, tape->merge_stage, - bytes_read)) + if (idetape_copy_stage_to_user(tape, buf, bytes_read)) ret = -EFAULT; buf += bytes_read; count -= bytes_read; @@ -2822,14 +2074,13 @@ static ssize_t idetape_chrdev_read(struct file *file, char __user *buf, if (bytes_read <= 0) goto finish; temp = min((unsigned long)count, (unsigned long)bytes_read); - if (idetape_copy_stage_to_user(tape, buf, tape->merge_stage, - temp)) + if (idetape_copy_stage_to_user(tape, buf, temp)) ret = -EFAULT; actually_read += temp; - tape->merge_stage_size = bytes_read-temp; + tape->merge_bh_size = bytes_read-temp; } finish: - if (!actually_read && test_bit(IDETAPE_FILEMARK, &tape->flags)) { + if (!actually_read && test_bit(IDETAPE_FLAG_FILEMARK, &tape->flags)) { debug_log(DBG_SENSE, "%s: spacing over filemark\n", tape->name); idetape_space_over_filemarks(drive, MTFSF, 1); @@ -2857,17 +2108,17 @@ static ssize_t idetape_chrdev_write(struct file *file, const char __user *buf, /* Initialize write operation */ if (tape->chrdev_dir != IDETAPE_DIR_WRITE) { if (tape->chrdev_dir == IDETAPE_DIR_READ) - idetape_discard_read_pipeline(drive, 1); - if (tape->merge_stage || tape->merge_stage_size) { - printk(KERN_ERR "ide-tape: merge_stage_size " + ide_tape_discard_merge_buffer(drive, 1); + if (tape->merge_bh || tape->merge_bh_size) { + printk(KERN_ERR "ide-tape: merge_bh_size " "should be 0 now\n"); - tape->merge_stage_size = 0; + tape->merge_bh_size = 0; } - tape->merge_stage = __idetape_kmalloc_stage(tape, 0, 0); - if (!tape->merge_stage) + tape->merge_bh = ide_tape_kmalloc_buffer(tape, 0, 0); + if (!tape->merge_bh) return -ENOMEM; tape->chrdev_dir = IDETAPE_DIR_WRITE; - idetape_init_merge_stage(tape); + idetape_init_merge_buffer(tape); /* * Issue a write 0 command to ensure that DSC handshake is @@ -2878,10 +2129,10 @@ static ssize_t idetape_chrdev_write(struct file *file, const char __user *buf, if (drive->dsc_overlap) { ssize_t retval = idetape_queue_rw_tail(drive, REQ_IDETAPE_WRITE, 0, - tape->merge_stage->bh); + tape->merge_bh); if (retval < 0) { - __idetape_kfree_stage(tape->merge_stage); - tape->merge_stage = NULL; + ide_tape_kfree_buffer(tape); + tape->merge_bh = NULL; tape->chrdev_dir = IDETAPE_DIR_NONE; return retval; } @@ -2889,56 +2140,51 @@ static ssize_t idetape_chrdev_write(struct file *file, const char __user *buf, } if (count == 0) return (0); - if (tape->restart_speed_control_req) - idetape_restart_speed_control(drive); - if (tape->merge_stage_size) { - if (tape->merge_stage_size >= tape->stage_size) { + if (tape->merge_bh_size) { + if (tape->merge_bh_size >= tape->buffer_size) { printk(KERN_ERR "ide-tape: bug: merge buf too big\n"); - tape->merge_stage_size = 0; + tape->merge_bh_size = 0; } actually_written = min((unsigned int) - (tape->stage_size - tape->merge_stage_size), + (tape->buffer_size - tape->merge_bh_size), (unsigned int)count); - if (idetape_copy_stage_from_user(tape, tape->merge_stage, buf, - actually_written)) + if (idetape_copy_stage_from_user(tape, buf, actually_written)) ret = -EFAULT; buf += actually_written; - tape->merge_stage_size += actually_written; + tape->merge_bh_size += actually_written; count -= actually_written; - if (tape->merge_stage_size == tape->stage_size) { + if (tape->merge_bh_size == tape->buffer_size) { ssize_t retval; - tape->merge_stage_size = 0; + tape->merge_bh_size = 0; retval = idetape_add_chrdev_write_request(drive, ctl); if (retval <= 0) return (retval); } } - while (count >= tape->stage_size) { + while (count >= tape->buffer_size) { ssize_t retval; - if (idetape_copy_stage_from_user(tape, tape->merge_stage, buf, - tape->stage_size)) + if (idetape_copy_stage_from_user(tape, buf, tape->buffer_size)) ret = -EFAULT; - buf += tape->stage_size; - count -= tape->stage_size; + buf += tape->buffer_size; + count -= tape->buffer_size; retval = idetape_add_chrdev_write_request(drive, ctl); - actually_written += tape->stage_size; + actually_written += tape->buffer_size; if (retval <= 0) return (retval); } if (count) { actually_written += count; - if (idetape_copy_stage_from_user(tape, tape->merge_stage, buf, - count)) + if (idetape_copy_stage_from_user(tape, buf, count)) ret = -EFAULT; - tape->merge_stage_size += count; + tape->merge_bh_size += count; } return ret ? ret : actually_written; } static int idetape_write_filemark(ide_drive_t *drive) { - idetape_pc_t pc; + struct ide_atapi_pc pc; /* Write a filemark */ idetape_create_write_filemark_cmd(drive, &pc, 1); @@ -2955,8 +2201,7 @@ static int idetape_write_filemark(ide_drive_t *drive) * * Note: MTBSF and MTBSFM are not supported when the tape doesn't support * spacing over filemarks in the reverse direction. In this case, MTFSFM is also - * usually not supported (it is supported in the rare case in which we crossed - * the filemark during our read-ahead pipelined operation mode). + * usually not supported. * * The following commands are currently not supported: * @@ -2966,13 +2211,12 @@ static int idetape_write_filemark(ide_drive_t *drive) static int idetape_mtioctop(ide_drive_t *drive, short mt_op, int mt_count) { idetape_tape_t *tape = drive->driver_data; - idetape_pc_t pc; + struct ide_atapi_pc pc; int i, retval; debug_log(DBG_ERR, "Handling MTIOCTOP ioctl: mt_op=%d, mt_count=%d\n", mt_op, mt_count); - /* Commands which need our pipelined read-ahead stages. */ switch (mt_op) { case MTFSF: case MTFSFM: @@ -2989,7 +2233,7 @@ static int idetape_mtioctop(ide_drive_t *drive, short mt_op, int mt_count) case MTWEOF: if (tape->write_prot) return -EACCES; - idetape_discard_read_pipeline(drive, 1); + ide_tape_discard_merge_buffer(drive, 1); for (i = 0; i < mt_count; i++) { retval = idetape_write_filemark(drive); if (retval) @@ -2997,12 +2241,12 @@ static int idetape_mtioctop(ide_drive_t *drive, short mt_op, int mt_count) } return 0; case MTREW: - idetape_discard_read_pipeline(drive, 0); + ide_tape_discard_merge_buffer(drive, 0); if (idetape_rewind_tape(drive)) return -EIO; return 0; case MTLOAD: - idetape_discard_read_pipeline(drive, 0); + ide_tape_discard_merge_buffer(drive, 0); idetape_create_load_unload_cmd(drive, &pc, IDETAPE_LU_LOAD_MASK); return idetape_queue_pc_tail(drive, &pc); @@ -3017,18 +2261,18 @@ static int idetape_mtioctop(ide_drive_t *drive, short mt_op, int mt_count) if (!idetape_queue_pc_tail(drive, &pc)) tape->door_locked = DOOR_UNLOCKED; } - idetape_discard_read_pipeline(drive, 0); + ide_tape_discard_merge_buffer(drive, 0); idetape_create_load_unload_cmd(drive, &pc, !IDETAPE_LU_LOAD_MASK); retval = idetape_queue_pc_tail(drive, &pc); if (!retval) - clear_bit(IDETAPE_MEDIUM_PRESENT, &tape->flags); + clear_bit(IDETAPE_FLAG_MEDIUM_PRESENT, &tape->flags); return retval; case MTNOP: - idetape_discard_read_pipeline(drive, 0); + ide_tape_discard_merge_buffer(drive, 0); return idetape_flush_tape_buffers(drive); case MTRETEN: - idetape_discard_read_pipeline(drive, 0); + ide_tape_discard_merge_buffer(drive, 0); idetape_create_load_unload_cmd(drive, &pc, IDETAPE_LU_RETENSION_MASK | IDETAPE_LU_LOAD_MASK); return idetape_queue_pc_tail(drive, &pc); @@ -3045,16 +2289,16 @@ static int idetape_mtioctop(ide_drive_t *drive, short mt_op, int mt_count) mt_count % tape->blk_size) return -EIO; tape->user_bs_factor = mt_count / tape->blk_size; - clear_bit(IDETAPE_DETECT_BS, &tape->flags); + clear_bit(IDETAPE_FLAG_DETECT_BS, &tape->flags); } else - set_bit(IDETAPE_DETECT_BS, &tape->flags); + set_bit(IDETAPE_FLAG_DETECT_BS, &tape->flags); return 0; case MTSEEK: - idetape_discard_read_pipeline(drive, 0); + ide_tape_discard_merge_buffer(drive, 0); return idetape_position_tape(drive, mt_count * tape->user_bs_factor, tape->partition, 0); case MTSETPART: - idetape_discard_read_pipeline(drive, 0); + ide_tape_discard_merge_buffer(drive, 0); return idetape_position_tape(drive, 0, mt_count, 0); case MTFSR: case MTBSR: @@ -3099,13 +2343,12 @@ static int idetape_chrdev_ioctl(struct inode *inode, struct file *file, debug_log(DBG_CHRDEV, "Enter %s, cmd=%u\n", __func__, cmd); - tape->restart_speed_control_req = 1; if (tape->chrdev_dir == IDETAPE_DIR_WRITE) { - idetape_empty_write_pipeline(drive); + ide_tape_flush_merge_buffer(drive); idetape_flush_tape_buffers(drive); } if (cmd == MTIOCGET || cmd == MTIOCPOS) { - block_offset = idetape_pipeline_size(drive) / + block_offset = tape->merge_bh_size / (tape->blk_size * tape->user_bs_factor); position = idetape_read_position(drive); if (position < 0) @@ -3137,7 +2380,7 @@ static int idetape_chrdev_ioctl(struct inode *inode, struct file *file, return 0; default: if (tape->chrdev_dir == IDETAPE_DIR_READ) - idetape_discard_read_pipeline(drive, 1); + ide_tape_discard_merge_buffer(drive, 1); return idetape_blkdev_ioctl(drive, cmd, arg); } } @@ -3149,7 +2392,7 @@ static int idetape_chrdev_ioctl(struct inode *inode, struct file *file, static void ide_tape_get_bsize_from_bdesc(ide_drive_t *drive) { idetape_tape_t *tape = drive->driver_data; - idetape_pc_t pc; + struct ide_atapi_pc pc; idetape_create_mode_sense_cmd(&pc, IDETAPE_BLOCK_DESCRIPTOR); if (idetape_queue_pc_tail(drive, &pc)) { @@ -3161,10 +2404,10 @@ static void ide_tape_get_bsize_from_bdesc(ide_drive_t *drive) } return; } - tape->blk_size = (pc.buffer[4 + 5] << 16) + - (pc.buffer[4 + 6] << 8) + - pc.buffer[4 + 7]; - tape->drv_write_prot = (pc.buffer[2] & 0x80) >> 7; + tape->blk_size = (pc.buf[4 + 5] << 16) + + (pc.buf[4 + 6] << 8) + + pc.buf[4 + 7]; + tape->drv_write_prot = (pc.buf[2] & 0x80) >> 7; } static int idetape_chrdev_open(struct inode *inode, struct file *filp) @@ -3172,7 +2415,7 @@ static int idetape_chrdev_open(struct inode *inode, struct file *filp) unsigned int minor = iminor(inode), i = minor & ~0xc0; ide_drive_t *drive; idetape_tape_t *tape; - idetape_pc_t pc; + struct ide_atapi_pc pc; int retval; if (i >= MAX_HWIFS * MAX_DRIVES) @@ -3195,25 +2438,22 @@ static int idetape_chrdev_open(struct inode *inode, struct file *filp) filp->private_data = tape; - if (test_and_set_bit(IDETAPE_BUSY, &tape->flags)) { + if (test_and_set_bit(IDETAPE_FLAG_BUSY, &tape->flags)) { retval = -EBUSY; goto out_put_tape; } retval = idetape_wait_ready(drive, 60 * HZ); if (retval) { - clear_bit(IDETAPE_BUSY, &tape->flags); + clear_bit(IDETAPE_FLAG_BUSY, &tape->flags); printk(KERN_ERR "ide-tape: %s: drive not ready\n", tape->name); goto out_put_tape; } idetape_read_position(drive); - if (!test_bit(IDETAPE_ADDRESS_VALID, &tape->flags)) + if (!test_bit(IDETAPE_FLAG_ADDRESS_VALID, &tape->flags)) (void)idetape_rewind_tape(drive); - if (tape->chrdev_dir != IDETAPE_DIR_READ) - clear_bit(IDETAPE_PIPELINE_ERROR, &tape->flags); - /* Read block size and write protect status from drive. */ ide_tape_get_bsize_from_bdesc(drive); @@ -3227,7 +2467,7 @@ static int idetape_chrdev_open(struct inode *inode, struct file *filp) if (tape->write_prot) { if ((filp->f_flags & O_ACCMODE) == O_WRONLY || (filp->f_flags & O_ACCMODE) == O_RDWR) { - clear_bit(IDETAPE_BUSY, &tape->flags); + clear_bit(IDETAPE_FLAG_BUSY, &tape->flags); retval = -EROFS; goto out_put_tape; } @@ -3242,8 +2482,6 @@ static int idetape_chrdev_open(struct inode *inode, struct file *filp) } } } - idetape_restart_speed_control(drive); - tape->restart_speed_control_req = 0; return 0; out_put_tape: @@ -3255,13 +2493,13 @@ static void idetape_write_release(ide_drive_t *drive, unsigned int minor) { idetape_tape_t *tape = drive->driver_data; - idetape_empty_write_pipeline(drive); - tape->merge_stage = __idetape_kmalloc_stage(tape, 1, 0); - if (tape->merge_stage != NULL) { + ide_tape_flush_merge_buffer(drive); + tape->merge_bh = ide_tape_kmalloc_buffer(tape, 1, 0); + if (tape->merge_bh != NULL) { idetape_pad_zeros(drive, tape->blk_size * (tape->user_bs_factor - 1)); - __idetape_kfree_stage(tape->merge_stage); - tape->merge_stage = NULL; + ide_tape_kfree_buffer(tape); + tape->merge_bh = NULL; } idetape_write_filemark(drive); idetape_flush_tape_buffers(drive); @@ -3272,7 +2510,7 @@ static int idetape_chrdev_release(struct inode *inode, struct file *filp) { struct ide_tape_obj *tape = ide_tape_f(filp); ide_drive_t *drive = tape->drive; - idetape_pc_t pc; + struct ide_atapi_pc pc; unsigned int minor = iminor(inode); lock_kernel(); @@ -3284,15 +2522,10 @@ static int idetape_chrdev_release(struct inode *inode, struct file *filp) idetape_write_release(drive, minor); if (tape->chrdev_dir == IDETAPE_DIR_READ) { if (minor < 128) - idetape_discard_read_pipeline(drive, 1); - else - idetape_wait_for_pipeline(drive); - } - if (tape->cache_stage != NULL) { - __idetape_kfree_stage(tape->cache_stage); - tape->cache_stage = NULL; + ide_tape_discard_merge_buffer(drive, 1); } - if (minor < 128 && test_bit(IDETAPE_MEDIUM_PRESENT, &tape->flags)) + + if (minor < 128 && test_bit(IDETAPE_FLAG_MEDIUM_PRESENT, &tape->flags)) (void) idetape_rewind_tape(drive); if (tape->chrdev_dir == IDETAPE_DIR_NONE) { if (tape->door_locked == DOOR_LOCKED) { @@ -3302,7 +2535,7 @@ static int idetape_chrdev_release(struct inode *inode, struct file *filp) } } } - clear_bit(IDETAPE_BUSY, &tape->flags); + clear_bit(IDETAPE_FLAG_BUSY, &tape->flags); ide_tape_put(tape); unlock_kernel(); return 0; @@ -3350,7 +2583,7 @@ static int idetape_identify_device(ide_drive_t *drive) static void idetape_get_inquiry_results(ide_drive_t *drive) { idetape_tape_t *tape = drive->driver_data; - idetape_pc_t pc; + struct ide_atapi_pc pc; char fw_rev[6], vendor_id[10], product_id[18]; idetape_create_inquiry_cmd(&pc); @@ -3359,9 +2592,9 @@ static void idetape_get_inquiry_results(ide_drive_t *drive) tape->name); return; } - memcpy(vendor_id, &pc.buffer[8], 8); - memcpy(product_id, &pc.buffer[16], 16); - memcpy(fw_rev, &pc.buffer[32], 4); + memcpy(vendor_id, &pc.buf[8], 8); + memcpy(product_id, &pc.buf[16], 16); + memcpy(fw_rev, &pc.buf[32], 4); ide_fixstring(vendor_id, 10, 0); ide_fixstring(product_id, 18, 0); @@ -3378,7 +2611,7 @@ static void idetape_get_inquiry_results(ide_drive_t *drive) static void idetape_get_mode_sense_results(ide_drive_t *drive) { idetape_tape_t *tape = drive->driver_data; - idetape_pc_t pc; + struct ide_atapi_pc pc; u8 *caps; u8 speed, max_speed; @@ -3392,7 +2625,7 @@ static void idetape_get_mode_sense_results(ide_drive_t *drive) put_unaligned(6*52, (u16 *)&tape->caps[16]); return; } - caps = pc.buffer + 4 + pc.buffer[3]; + caps = pc.buf + 4 + pc.buf[3]; /* convert to host order and save for later use */ speed = be16_to_cpu(*(u16 *)&caps[14]); @@ -3428,33 +2661,15 @@ static void idetape_add_settings(ide_drive_t *drive) ide_add_setting(drive, "buffer", SETTING_READ, TYPE_SHORT, 0, 0xffff, 1, 2, (u16 *)&tape->caps[16], NULL); - ide_add_setting(drive, "pipeline_min", SETTING_RW, TYPE_INT, 1, 0xffff, - tape->stage_size / 1024, 1, &tape->min_pipeline, NULL); - ide_add_setting(drive, "pipeline", SETTING_RW, TYPE_INT, 1, 0xffff, - tape->stage_size / 1024, 1, &tape->max_stages, NULL); - ide_add_setting(drive, "pipeline_max", SETTING_RW, TYPE_INT, 1, 0xffff, - tape->stage_size / 1024, 1, &tape->max_pipeline, NULL); - ide_add_setting(drive, "pipeline_used", SETTING_READ, TYPE_INT, 0, - 0xffff, tape->stage_size / 1024, 1, &tape->nr_stages, - NULL); - ide_add_setting(drive, "pipeline_pending", SETTING_READ, TYPE_INT, 0, - 0xffff, tape->stage_size / 1024, 1, - &tape->nr_pending_stages, NULL); ide_add_setting(drive, "speed", SETTING_READ, TYPE_SHORT, 0, 0xffff, 1, 1, (u16 *)&tape->caps[14], NULL); - ide_add_setting(drive, "stage", SETTING_READ, TYPE_INT, 0, 0xffff, 1, - 1024, &tape->stage_size, NULL); + ide_add_setting(drive, "buffer_size", SETTING_READ, TYPE_INT, 0, 0xffff, + 1, 1024, &tape->buffer_size, NULL); ide_add_setting(drive, "tdsc", SETTING_RW, TYPE_INT, IDETAPE_DSC_RW_MIN, IDETAPE_DSC_RW_MAX, 1000, HZ, &tape->best_dsc_rw_freq, NULL); ide_add_setting(drive, "dsc_overlap", SETTING_RW, TYPE_BYTE, 0, 1, 1, 1, &drive->dsc_overlap, NULL); - ide_add_setting(drive, "pipeline_head_speed_c", SETTING_READ, TYPE_INT, - 0, 0xffff, 1, 1, &tape->controlled_pipeline_head_speed, - NULL); - ide_add_setting(drive, "pipeline_head_speed_u", SETTING_READ, TYPE_INT, - 0, 0xffff, 1, 1, - &tape->uncontrolled_pipeline_head_speed, NULL); ide_add_setting(drive, "avg_speed", SETTING_READ, TYPE_INT, 0, 0xffff, 1, 1, &tape->avg_speed, NULL); ide_add_setting(drive, "debug_mask", SETTING_RW, TYPE_INT, 0, 0xffff, 1, @@ -3477,11 +2692,10 @@ static inline void idetape_add_settings(ide_drive_t *drive) { ; } */ static void idetape_setup(ide_drive_t *drive, idetape_tape_t *tape, int minor) { - unsigned long t1, tmid, tn, t; + unsigned long t; int speed; - int stage_size; + int buffer_size; u8 gcw[2]; - struct sysinfo si; u16 *ctl = (u16 *)&tape->caps[12]; spin_lock_init(&tape->lock); @@ -3500,65 +2714,33 @@ static void idetape_setup(ide_drive_t *drive, idetape_tape_t *tape, int minor) tape->name[2] = '0' + minor; tape->chrdev_dir = IDETAPE_DIR_NONE; tape->pc = tape->pc_stack; - tape->max_insert_speed = 10000; - tape->speed_control = 1; *((unsigned short *) &gcw) = drive->id->config; /* Command packet DRQ type */ if (((gcw[0] & 0x60) >> 5) == 1) - set_bit(IDETAPE_DRQ_INTERRUPT, &tape->flags); - - tape->min_pipeline = 10; - tape->max_pipeline = 10; - tape->max_stages = 10; + set_bit(IDETAPE_FLAG_DRQ_INTERRUPT, &tape->flags); idetape_get_inquiry_results(drive); idetape_get_mode_sense_results(drive); ide_tape_get_bsize_from_bdesc(drive); tape->user_bs_factor = 1; - tape->stage_size = *ctl * tape->blk_size; - while (tape->stage_size > 0xffff) { + tape->buffer_size = *ctl * tape->blk_size; + while (tape->buffer_size > 0xffff) { printk(KERN_NOTICE "ide-tape: decreasing stage size\n"); *ctl /= 2; - tape->stage_size = *ctl * tape->blk_size; + tape->buffer_size = *ctl * tape->blk_size; } - stage_size = tape->stage_size; - tape->pages_per_stage = stage_size / PAGE_SIZE; - if (stage_size % PAGE_SIZE) { - tape->pages_per_stage++; - tape->excess_bh_size = PAGE_SIZE - stage_size % PAGE_SIZE; + buffer_size = tape->buffer_size; + tape->pages_per_buffer = buffer_size / PAGE_SIZE; + if (buffer_size % PAGE_SIZE) { + tape->pages_per_buffer++; + tape->excess_bh_size = PAGE_SIZE - buffer_size % PAGE_SIZE; } - /* Select the "best" DSC read/write polling freq and pipeline size. */ + /* select the "best" DSC read/write polling freq */ speed = max(*(u16 *)&tape->caps[14], *(u16 *)&tape->caps[8]); - tape->max_stages = speed * 1000 * 10 / tape->stage_size; - - /* Limit memory use for pipeline to 10% of physical memory */ - si_meminfo(&si); - if (tape->max_stages * tape->stage_size > - si.totalram * si.mem_unit / 10) - tape->max_stages = - si.totalram * si.mem_unit / (10 * tape->stage_size); - - tape->max_stages = min(tape->max_stages, IDETAPE_MAX_PIPELINE_STAGES); - tape->min_pipeline = min(tape->max_stages, IDETAPE_MIN_PIPELINE_STAGES); - tape->max_pipeline = - min(tape->max_stages * 2, IDETAPE_MAX_PIPELINE_STAGES); - if (tape->max_stages == 0) { - tape->max_stages = 1; - tape->min_pipeline = 1; - tape->max_pipeline = 1; - } - - t1 = (tape->stage_size * HZ) / (speed * 1000); - tmid = (*(u16 *)&tape->caps[16] * 32 * HZ) / (speed * 125); - tn = (IDETAPE_FIFO_THRESHOLD * tape->stage_size * HZ) / (speed * 1000); - - if (tape->max_stages) - t = tn; - else - t = t1; + t = (IDETAPE_FIFO_THRESHOLD * tape->buffer_size * HZ) / (speed * 1000); /* * Ensure that the number we got makes sense; limit it within @@ -3568,11 +2750,10 @@ static void idetape_setup(ide_drive_t *drive, idetape_tape_t *tape, int minor) min_t(unsigned long, t, IDETAPE_DSC_RW_MAX), IDETAPE_DSC_RW_MIN); printk(KERN_INFO "ide-tape: %s <-> %s: %dKBps, %d*%dkB buffer, " - "%dkB pipeline, %lums tDSC%s\n", + "%lums tDSC%s\n", drive->name, tape->name, *(u16 *)&tape->caps[14], - (*(u16 *)&tape->caps[16] * 512) / tape->stage_size, - tape->stage_size / 1024, - tape->max_stages * tape->stage_size / 1024, + (*(u16 *)&tape->caps[16] * 512) / tape->buffer_size, + tape->buffer_size / 1024, tape->best_dsc_rw_freq * 1000 / HZ, drive->using_dma ? ", DMA":""); @@ -3596,7 +2777,7 @@ static void ide_tape_release(struct kref *kref) ide_drive_t *drive = tape->drive; struct gendisk *g = tape->disk; - BUG_ON(tape->first_stage != NULL || tape->merge_stage_size); + BUG_ON(tape->merge_bh_size); drive->dsc_overlap = 0; drive->driver_data = NULL; |