diff options
Diffstat (limited to 'drivers/ide/pci/sl82c105.c')
| -rw-r--r-- | drivers/ide/pci/sl82c105.c | 35 |
1 files changed, 23 insertions, 12 deletions
diff --git a/drivers/ide/pci/sl82c105.c b/drivers/ide/pci/sl82c105.c index ce84fa045d3..84dc33602ff 100644 --- a/drivers/ide/pci/sl82c105.c +++ b/drivers/ide/pci/sl82c105.c @@ -17,12 +17,13 @@ #include <linux/types.h> #include <linux/module.h> #include <linux/kernel.h> -#include <linux/hdreg.h> #include <linux/pci.h> #include <linux/ide.h> #include <asm/io.h> +#define DRV_NAME "sl82c105" + #undef DEBUG #ifdef DEBUG @@ -47,10 +48,11 @@ */ static unsigned int get_pio_timings(ide_drive_t *drive, u8 pio) { + struct ide_timing *t = ide_timing_find_mode(XFER_PIO_0 + pio); unsigned int cmd_on, cmd_off; u8 iordy = 0; - cmd_on = (ide_pio_timings[pio].active_time + 29) / 30; + cmd_on = (t->active + 29) / 30; cmd_off = (ide_pio_cycle_time(drive, pio) - 30 * cmd_on + 29) / 30; if (cmd_on == 0) @@ -59,7 +61,7 @@ static unsigned int get_pio_timings(ide_drive_t *drive, u8 pio) if (cmd_off == 0) cmd_off = 1; - if (pio > 2 || ide_dev_has_iordy(drive->id)) + if (pio > 2 || ata_id_has_iordy(drive->id)) iordy = 0x40; return (cmd_on - 1) << 8 | (cmd_off - 1) | iordy; @@ -156,9 +158,9 @@ static void sl82c105_dma_lost_irq(ide_drive_t *drive) * Was DMA enabled? If so, disable it - we're resetting the * host. The IDE layer will be handling the drive for us. */ - dma_cmd = inb(hwif->dma_command); + dma_cmd = inb(hwif->dma_base + ATA_DMA_CMD); if (dma_cmd & 1) { - outb(dma_cmd & ~1, hwif->dma_command); + outb(dma_cmd & ~1, hwif->dma_base + ATA_DMA_CMD); printk("sl82c105: DMA was enabled\n"); } @@ -205,7 +207,7 @@ static int sl82c105_dma_end(ide_drive_t *drive) DBG(("%s(drive:%s)\n", __func__, drive->name)); - ret = __ide_dma_end(drive); + ret = ide_dma_end(drive); pci_write_config_word(dev, reg, drive->drive_data); @@ -269,7 +271,7 @@ static u8 sl82c105_bridge_revision(struct pci_dev *dev) * channel 0 here at least, but channel 1 has to be enabled by * firmware or arch code. We still set both to 16 bits mode. */ -static unsigned int __devinit init_chipset_sl82c105(struct pci_dev *dev, const char *msg) +static unsigned int init_chipset_sl82c105(struct pci_dev *dev) { u32 val; @@ -300,7 +302,7 @@ static const struct ide_dma_ops sl82c105_dma_ops = { }; static const struct ide_port_info sl82c105_chipset __devinitdata = { - .name = "W82C105", + .name = DRV_NAME, .init_chipset = init_chipset_sl82c105, .enablebits = {{0x40,0x01,0x01}, {0x40,0x10,0x10}}, .port_ops = &sl82c105_port_ops, @@ -327,14 +329,14 @@ static int __devinit sl82c105_init_one(struct pci_dev *dev, const struct pci_dev * Never ever EVER under any circumstances enable * DMA when the bridge is this old. */ - printk(KERN_INFO "W82C105_IDE: Winbond W83C553 bridge " + printk(KERN_INFO DRV_NAME ": Winbond W83C553 bridge " "revision %d, BM-DMA disabled\n", rev); d.dma_ops = NULL; d.mwdma_mask = 0; d.host_flags &= ~IDE_HFLAG_SERIALIZE_DMA; } - return ide_setup_pci_device(dev, &d); + return ide_pci_init_one(dev, &d, NULL); } static const struct pci_device_id sl82c105_pci_tbl[] = { @@ -343,18 +345,27 @@ static const struct pci_device_id sl82c105_pci_tbl[] = { }; MODULE_DEVICE_TABLE(pci, sl82c105_pci_tbl); -static struct pci_driver driver = { +static struct pci_driver sl82c105_pci_driver = { .name = "W82C105_IDE", .id_table = sl82c105_pci_tbl, .probe = sl82c105_init_one, + .remove = ide_pci_remove, + .suspend = ide_pci_suspend, + .resume = ide_pci_resume, }; static int __init sl82c105_ide_init(void) { - return ide_pci_register_driver(&driver); + return ide_pci_register_driver(&sl82c105_pci_driver); +} + +static void __exit sl82c105_ide_exit(void) +{ + pci_unregister_driver(&sl82c105_pci_driver); } module_init(sl82c105_ide_init); +module_exit(sl82c105_ide_exit); MODULE_DESCRIPTION("PCI driver module for W82C105 IDE"); MODULE_LICENSE("GPL"); |