summaryrefslogtreecommitdiffstats
path: root/drivers/ide/serverworks.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/ide/serverworks.c')
-rw-r--r--drivers/ide/serverworks.c470
1 files changed, 470 insertions, 0 deletions
diff --git a/drivers/ide/serverworks.c b/drivers/ide/serverworks.c
new file mode 100644
index 00000000000..437bc919daf
--- /dev/null
+++ b/drivers/ide/serverworks.c
@@ -0,0 +1,470 @@
+/*
+ * Copyright (C) 1998-2000 Michel Aubry
+ * Copyright (C) 1998-2000 Andrzej Krzysztofowicz
+ * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
+ * Copyright (C) 2007 Bartlomiej Zolnierkiewicz
+ * Portions copyright (c) 2001 Sun Microsystems
+ *
+ *
+ * RCC/ServerWorks IDE driver for Linux
+ *
+ * OSB4: `Open South Bridge' IDE Interface (fn 1)
+ * supports UDMA mode 2 (33 MB/s)
+ *
+ * CSB5: `Champion South Bridge' IDE Interface (fn 1)
+ * all revisions support UDMA mode 4 (66 MB/s)
+ * revision A2.0 and up support UDMA mode 5 (100 MB/s)
+ *
+ * *** The CSB5 does not provide ANY register ***
+ * *** to detect 80-conductor cable presence. ***
+ *
+ * CSB6: `Champion South Bridge' IDE Interface (optional: third channel)
+ *
+ * HT1000: AKA BCM5785 - Hypertransport Southbridge for Opteron systems. IDE
+ * controller same as the CSB6. Single channel ATA100 only.
+ *
+ * Documentation:
+ * Available under NDA only. Errata info very hard to get.
+ *
+ */
+
+#include <linux/types.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/ide.h>
+#include <linux/init.h>
+
+#include <asm/io.h>
+
+#define DRV_NAME "serverworks"
+
+#define SVWKS_CSB5_REVISION_NEW 0x92 /* min PCI_REVISION_ID for UDMA5 (A2.0) */
+#define SVWKS_CSB6_REVISION 0xa0 /* min PCI_REVISION_ID for UDMA4 (A1.0) */
+
+/* Seagate Barracuda ATA IV Family drives in UDMA mode 5
+ * can overrun their FIFOs when used with the CSB5 */
+static const char *svwks_bad_ata100[] = {
+ "ST320011A",
+ "ST340016A",
+ "ST360021A",
+ "ST380021A",
+ NULL
+};
+
+static struct pci_dev *isa_dev;
+
+static int check_in_drive_lists (ide_drive_t *drive, const char **list)
+{
+ char *m = (char *)&drive->id[ATA_ID_PROD];
+
+ while (*list)
+ if (!strcmp(*list++, m))
+ return 1;
+ return 0;
+}
+
+static u8 svwks_udma_filter(ide_drive_t *drive)
+{
+ struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
+ u8 mask = 0;
+
+ if (dev->device == PCI_DEVICE_ID_SERVERWORKS_HT1000IDE)
+ return 0x1f;
+ if (dev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4IDE) {
+ u32 reg = 0;
+ if (isa_dev)
+ pci_read_config_dword(isa_dev, 0x64, &reg);
+
+ /*
+ * Don't enable UDMA on disk devices for the moment
+ */
+ if(drive->media == ide_disk)
+ return 0;
+ /* Check the OSB4 DMA33 enable bit */
+ return ((reg & 0x00004000) == 0x00004000) ? 0x07 : 0;
+ } else if (dev->revision < SVWKS_CSB5_REVISION_NEW) {
+ return 0x07;
+ } else if (dev->revision >= SVWKS_CSB5_REVISION_NEW) {
+ u8 btr = 0, mode;
+ pci_read_config_byte(dev, 0x5A, &btr);
+ mode = btr & 0x3;
+
+ /* If someone decides to do UDMA133 on CSB5 the same
+ issue will bite so be inclusive */
+ if (mode > 2 && check_in_drive_lists(drive, svwks_bad_ata100))
+ mode = 2;
+
+ switch(mode) {
+ case 3: mask = 0x3f; break;
+ case 2: mask = 0x1f; break;
+ case 1: mask = 0x07; break;
+ default: mask = 0x00; break;
+ }
+ }
+ if (((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
+ (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)) &&
+ (!(PCI_FUNC(dev->devfn) & 1)))
+ mask = 0x1f;
+
+ return mask;
+}
+
+static u8 svwks_csb_check (struct pci_dev *dev)
+{
+ switch (dev->device) {
+ case PCI_DEVICE_ID_SERVERWORKS_CSB5IDE:
+ case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE:
+ case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2:
+ case PCI_DEVICE_ID_SERVERWORKS_HT1000IDE:
+ return 1;
+ default:
+ break;
+ }
+ return 0;
+}
+
+static void svwks_set_pio_mode(ide_drive_t *drive, const u8 pio)
+{
+ static const u8 pio_modes[] = { 0x5d, 0x47, 0x34, 0x22, 0x20 };
+ static const u8 drive_pci[] = { 0x41, 0x40, 0x43, 0x42 };
+
+ struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
+
+ pci_write_config_byte(dev, drive_pci[drive->dn], pio_modes[pio]);
+
+ if (svwks_csb_check(dev)) {
+ u16 csb_pio = 0;
+
+ pci_read_config_word(dev, 0x4a, &csb_pio);
+
+ csb_pio &= ~(0x0f << (4 * drive->dn));
+ csb_pio |= (pio << (4 * drive->dn));
+
+ pci_write_config_word(dev, 0x4a, csb_pio);
+ }
+}
+
+static void svwks_set_dma_mode(ide_drive_t *drive, const u8 speed)
+{
+ static const u8 udma_modes[] = { 0x00, 0x01, 0x02, 0x03, 0x04, 0x05 };
+ static const u8 dma_modes[] = { 0x77, 0x21, 0x20 };
+ static const u8 drive_pci2[] = { 0x45, 0x44, 0x47, 0x46 };
+
+ ide_hwif_t *hwif = HWIF(drive);
+ struct pci_dev *dev = to_pci_dev(hwif->dev);
+ u8 unit = drive->dn & 1;
+
+ u8 ultra_enable = 0, ultra_timing = 0, dma_timing = 0;
+
+ pci_read_config_byte(dev, (0x56|hwif->channel), &ultra_timing);
+ pci_read_config_byte(dev, 0x54, &ultra_enable);
+
+ ultra_timing &= ~(0x0F << (4*unit));
+ ultra_enable &= ~(0x01 << drive->dn);
+
+ if (speed >= XFER_UDMA_0) {
+ dma_timing |= dma_modes[2];
+ ultra_timing |= (udma_modes[speed - XFER_UDMA_0] << (4 * unit));
+ ultra_enable |= (0x01 << drive->dn);
+ } else if (speed >= XFER_MW_DMA_0)
+ dma_timing |= dma_modes[speed - XFER_MW_DMA_0];
+
+ pci_write_config_byte(dev, drive_pci2[drive->dn], dma_timing);
+ pci_write_config_byte(dev, (0x56|hwif->channel), ultra_timing);
+ pci_write_config_byte(dev, 0x54, ultra_enable);
+}
+
+static unsigned int init_chipset_svwks(struct pci_dev *dev)
+{
+ unsigned int reg;
+ u8 btr;
+
+ /* force Master Latency Timer value to 64 PCICLKs */
+ pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x40);
+
+ /* OSB4 : South Bridge and IDE */
+ if (dev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4IDE) {
+ isa_dev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
+ PCI_DEVICE_ID_SERVERWORKS_OSB4, NULL);
+ if (isa_dev) {
+ pci_read_config_dword(isa_dev, 0x64, &reg);
+ reg &= ~0x00002000; /* disable 600ns interrupt mask */
+ if(!(reg & 0x00004000))
+ printk(KERN_DEBUG DRV_NAME " %s: UDMA not BIOS "
+ "enabled.\n", pci_name(dev));
+ reg |= 0x00004000; /* enable UDMA/33 support */
+ pci_write_config_dword(isa_dev, 0x64, reg);
+ }
+ }
+
+ /* setup CSB5/CSB6 : South Bridge and IDE option RAID */
+ else if ((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE) ||
+ (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
+ (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)) {
+
+ /* Third Channel Test */
+ if (!(PCI_FUNC(dev->devfn) & 1)) {
+ struct pci_dev * findev = NULL;
+ u32 reg4c = 0;
+ findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
+ PCI_DEVICE_ID_SERVERWORKS_CSB5, NULL);
+ if (findev) {
+ pci_read_config_dword(findev, 0x4C, &reg4c);
+ reg4c &= ~0x000007FF;
+ reg4c |= 0x00000040;
+ reg4c |= 0x00000020;
+ pci_write_config_dword(findev, 0x4C, reg4c);
+ pci_dev_put(findev);
+ }
+ outb_p(0x06, 0x0c00);
+ dev->irq = inb_p(0x0c01);
+ } else {
+ struct pci_dev * findev = NULL;
+ u8 reg41 = 0;
+
+ findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
+ PCI_DEVICE_ID_SERVERWORKS_CSB6, NULL);
+ if (findev) {
+ pci_read_config_byte(findev, 0x41, &reg41);
+ reg41 &= ~0x40;
+ pci_write_config_byte(findev, 0x41, reg41);
+ pci_dev_put(findev);
+ }
+ /*
+ * This is a device pin issue on CSB6.
+ * Since there will be a future raid mode,
+ * early versions of the chipset require the
+ * interrupt pin to be set, and it is a compatibility
+ * mode issue.
+ */
+ if ((dev->class >> 8) == PCI_CLASS_STORAGE_IDE)
+ dev->irq = 0;
+ }
+// pci_read_config_dword(dev, 0x40, &pioreg)
+// pci_write_config_dword(dev, 0x40, 0x99999999);
+// pci_read_config_dword(dev, 0x44, &dmareg);
+// pci_write_config_dword(dev, 0x44, 0xFFFFFFFF);
+ /* setup the UDMA Control register
+ *
+ * 1. clear bit 6 to enable DMA
+ * 2. enable DMA modes with bits 0-1
+ * 00 : legacy
+ * 01 : udma2
+ * 10 : udma2/udma4
+ * 11 : udma2/udma4/udma5
+ */
+ pci_read_config_byte(dev, 0x5A, &btr);
+ btr &= ~0x40;
+ if (!(PCI_FUNC(dev->devfn) & 1))
+ btr |= 0x2;
+ else
+ btr |= (dev->revision >= SVWKS_CSB5_REVISION_NEW) ? 0x3 : 0x2;
+ pci_write_config_byte(dev, 0x5A, btr);
+ }
+ /* Setup HT1000 SouthBridge Controller - Single Channel Only */
+ else if (dev->device == PCI_DEVICE_ID_SERVERWORKS_HT1000IDE) {
+ pci_read_config_byte(dev, 0x5A, &btr);
+ btr &= ~0x40;
+ btr |= 0x3;
+ pci_write_config_byte(dev, 0x5A, btr);
+ }
+
+ return dev->irq;
+}
+
+static u8 ata66_svwks_svwks(ide_hwif_t *hwif)
+{
+ return ATA_CBL_PATA80;
+}
+
+/* On Dell PowerEdge servers with a CSB5/CSB6, the top two bits
+ * of the subsystem device ID indicate presence of an 80-pin cable.
+ * Bit 15 clear = secondary IDE channel does not have 80-pin cable.
+ * Bit 15 set = secondary IDE channel has 80-pin cable.
+ * Bit 14 clear = primary IDE channel does not have 80-pin cable.
+ * Bit 14 set = primary IDE channel has 80-pin cable.
+ */
+static u8 ata66_svwks_dell(ide_hwif_t *hwif)
+{
+ struct pci_dev *dev = to_pci_dev(hwif->dev);
+
+ if (dev->subsystem_vendor == PCI_VENDOR_ID_DELL &&
+ dev->vendor == PCI_VENDOR_ID_SERVERWORKS &&
+ (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE ||
+ dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE))
+ return ((1 << (hwif->channel + 14)) &
+ dev->subsystem_device) ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
+ return ATA_CBL_PATA40;
+}
+
+/* Sun Cobalt Alpine hardware avoids the 80-pin cable
+ * detect issue by attaching the drives directly to the board.
+ * This check follows the Dell precedent (how scary is that?!)
+ *
+ * WARNING: this only works on Alpine hardware!
+ */
+static u8 ata66_svwks_cobalt(ide_hwif_t *hwif)
+{
+ struct pci_dev *dev = to_pci_dev(hwif->dev);
+
+ if (dev->subsystem_vendor == PCI_VENDOR_ID_SUN &&
+ dev->vendor == PCI_VENDOR_ID_SERVERWORKS &&
+ dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE)
+ return ((1 << (hwif->channel + 14)) &
+ dev->subsystem_device) ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
+ return ATA_CBL_PATA40;
+}
+
+static u8 svwks_cable_detect(ide_hwif_t *hwif)
+{
+ struct pci_dev *dev = to_pci_dev(hwif->dev);
+
+ /* Server Works */
+ if (dev->subsystem_vendor == PCI_VENDOR_ID_SERVERWORKS)
+ return ata66_svwks_svwks (hwif);
+
+ /* Dell PowerEdge */
+ if (dev->subsystem_vendor == PCI_VENDOR_ID_DELL)
+ return ata66_svwks_dell (hwif);
+
+ /* Cobalt Alpine */
+ if (dev->subsystem_vendor == PCI_VENDOR_ID_SUN)
+ return ata66_svwks_cobalt (hwif);
+
+ /* Per Specified Design by OEM, and ASIC Architect */
+ if ((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
+ (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2))
+ return ATA_CBL_PATA80;
+
+ return ATA_CBL_PATA40;
+}
+
+static const struct ide_port_ops osb4_port_ops = {
+ .set_pio_mode = svwks_set_pio_mode,
+ .set_dma_mode = svwks_set_dma_mode,
+ .udma_filter = svwks_udma_filter,
+};
+
+static const struct ide_port_ops svwks_port_ops = {
+ .set_pio_mode = svwks_set_pio_mode,
+ .set_dma_mode = svwks_set_dma_mode,
+ .udma_filter = svwks_udma_filter,
+ .cable_detect = svwks_cable_detect,
+};
+
+#define IDE_HFLAGS_SVWKS IDE_HFLAG_LEGACY_IRQS
+
+static const struct ide_port_info serverworks_chipsets[] __devinitdata = {
+ { /* 0: OSB4 */
+ .name = DRV_NAME,
+ .init_chipset = init_chipset_svwks,
+ .port_ops = &osb4_port_ops,
+ .host_flags = IDE_HFLAGS_SVWKS,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = 0x00, /* UDMA is problematic on OSB4 */
+ },
+ { /* 1: CSB5 */
+ .name = DRV_NAME,
+ .init_chipset = init_chipset_svwks,
+ .port_ops = &svwks_port_ops,
+ .host_flags = IDE_HFLAGS_SVWKS,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA5,
+ },
+ { /* 2: CSB6 */
+ .name = DRV_NAME,
+ .init_chipset = init_chipset_svwks,
+ .port_ops = &svwks_port_ops,
+ .host_flags = IDE_HFLAGS_SVWKS,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA5,
+ },
+ { /* 3: CSB6-2 */
+ .name = DRV_NAME,
+ .init_chipset = init_chipset_svwks,
+ .port_ops = &svwks_port_ops,
+ .host_flags = IDE_HFLAGS_SVWKS | IDE_HFLAG_SINGLE,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA5,
+ },
+ { /* 4: HT1000 */
+ .name = DRV_NAME,
+ .init_chipset = init_chipset_svwks,
+ .port_ops = &svwks_port_ops,
+ .host_flags = IDE_HFLAGS_SVWKS | IDE_HFLAG_SINGLE,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA5,
+ }
+};
+
+/**
+ * svwks_init_one - called when a OSB/CSB is found
+ * @dev: the svwks device
+ * @id: the matching pci id
+ *
+ * Called when the PCI registration layer (or the IDE initialization)
+ * finds a device matching our IDE device tables.
+ */
+
+static int __devinit svwks_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+ struct ide_port_info d;
+ u8 idx = id->driver_data;
+
+ d = serverworks_chipsets[idx];
+
+ if (idx == 1)
+ d.host_flags |= IDE_HFLAG_CLEAR_SIMPLEX;
+ else if (idx == 2 || idx == 3) {
+ if ((PCI_FUNC(dev->devfn) & 1) == 0) {
+ if (pci_resource_start(dev, 0) != 0x01f1)
+ d.host_flags |= IDE_HFLAG_NON_BOOTABLE;
+ d.host_flags |= IDE_HFLAG_SINGLE;
+ } else
+ d.host_flags &= ~IDE_HFLAG_SINGLE;
+ }
+
+ return ide_pci_init_one(dev, &d, NULL);
+}
+
+static const struct pci_device_id svwks_pci_tbl[] = {
+ { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_OSB4IDE), 0 },
+ { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE), 1 },
+ { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE), 2 },
+ { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2), 3 },
+ { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000IDE), 4 },
+ { 0, },
+};
+MODULE_DEVICE_TABLE(pci, svwks_pci_tbl);
+
+static struct pci_driver svwks_pci_driver = {
+ .name = "Serverworks_IDE",
+ .id_table = svwks_pci_tbl,
+ .probe = svwks_init_one,
+ .remove = ide_pci_remove,
+ .suspend = ide_pci_suspend,
+ .resume = ide_pci_resume,
+};
+
+static int __init svwks_ide_init(void)
+{
+ return ide_pci_register_driver(&svwks_pci_driver);
+}
+
+static void __exit svwks_ide_exit(void)
+{
+ pci_unregister_driver(&svwks_pci_driver);
+}
+
+module_init(svwks_ide_init);
+module_exit(svwks_ide_exit);
+
+MODULE_AUTHOR("Michael Aubry. Andrzej Krzysztofowicz, Andre Hedrick");
+MODULE_DESCRIPTION("PCI driver module for Serverworks OSB4/CSB5/CSB6 IDE");
+MODULE_LICENSE("GPL");