diff options
Diffstat (limited to 'drivers/ide')
-rw-r--r-- | drivers/ide/Kconfig | 9 | ||||
-rw-r--r-- | drivers/ide/pci/Makefile | 1 | ||||
-rw-r--r-- | drivers/ide/pci/it8172.c | 307 |
3 files changed, 0 insertions, 317 deletions
diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig index abcabb29559..0c68d0f0d8e 100644 --- a/drivers/ide/Kconfig +++ b/drivers/ide/Kconfig @@ -614,15 +614,6 @@ config BLK_DEV_PIIX the kernel to change PIO, DMA and UDMA speeds and to configure the chip to optimum performance. -config BLK_DEV_IT8172 - bool "IT8172 IDE support" - depends on (MIPS_ITE8172 || MIPS_IVR) - help - Say Y here to support the on-board IDE controller on the Integrated - Technology Express, Inc. ITE8172 SBC. Vendor page at - <http://www.ite.com.tw/ia/brief_it8172bsp.htm>; picture of the - board at <http://www.mvista.com/partners/semiconductor/ite.html>. - config BLK_DEV_IT821X tristate "IT821X IDE support" help diff --git a/drivers/ide/pci/Makefile b/drivers/ide/pci/Makefile index 640a54b09b5..fef08960aa4 100644 --- a/drivers/ide/pci/Makefile +++ b/drivers/ide/pci/Makefile @@ -12,7 +12,6 @@ obj-$(CONFIG_BLK_DEV_CY82C693) += cy82c693.o obj-$(CONFIG_BLK_DEV_HPT34X) += hpt34x.o obj-$(CONFIG_BLK_DEV_HPT366) += hpt366.o #obj-$(CONFIG_BLK_DEV_HPT37X) += hpt37x.o -obj-$(CONFIG_BLK_DEV_IT8172) += it8172.o obj-$(CONFIG_BLK_DEV_IT821X) += it821x.o obj-$(CONFIG_BLK_DEV_JMICRON) += jmicron.o obj-$(CONFIG_BLK_DEV_NS87415) += ns87415.o diff --git a/drivers/ide/pci/it8172.c b/drivers/ide/pci/it8172.c deleted file mode 100644 index 0fc89fafad6..00000000000 --- a/drivers/ide/pci/it8172.c +++ /dev/null @@ -1,307 +0,0 @@ -/* - * - * BRIEF MODULE DESCRIPTION - * IT8172 IDE controller support - * - * Copyright 2000 MontaVista Software Inc. - * Author: MontaVista Software, Inc. - * stevel@mvista.com or source@mvista.com - * - * This program is free software; you can redistribute it and/or modify it - * under the terms of the GNU General Public License as published by the - * Free Software Foundation; either version 2 of the License, or (at your - * option) any later version. - * - * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED - * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF - * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN - * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, - * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT - * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF - * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON - * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT - * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF - * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - * You should have received a copy of the GNU General Public License along - * with this program; if not, write to the Free Software Foundation, Inc., - * 675 Mass Ave, Cambridge, MA 02139, USA. - */ - -#include <linux/module.h> -#include <linux/types.h> -#include <linux/kernel.h> -#include <linux/ioport.h> -#include <linux/pci.h> -#include <linux/hdreg.h> -#include <linux/ide.h> -#include <linux/delay.h> -#include <linux/init.h> - -#include <asm/io.h> -#include <asm/it8172/it8172_int.h> - -/* - * Prototypes - */ -static u8 it8172_ratemask (ide_drive_t *drive) -{ - return 1; -} - -static void it8172_tune_drive (ide_drive_t *drive, u8 pio) -{ - ide_hwif_t *hwif = HWIF(drive); - struct pci_dev *dev = hwif->pci_dev; - int is_slave = (&hwif->drives[1] == drive); - unsigned long flags; - u16 drive_enables; - u32 drive_timing; - - pio = ide_get_best_pio_mode(drive, pio, 4, NULL); - spin_lock_irqsave(&ide_lock, flags); - pci_read_config_word(dev, 0x40, &drive_enables); - pci_read_config_dword(dev, 0x44, &drive_timing); - - /* - * FIX! The DIOR/DIOW pulse width and recovery times in port 0x44 - * are being left at the default values of 8 PCI clocks (242 nsec - * for a 33 MHz clock). These can be safely shortened at higher - * PIO modes. The DIOR/DIOW pulse width and recovery times only - * apply to PIO modes, not to the DMA modes. - */ - - /* - * Enable port 0x44. The IT8172G spec is confused; it calls - * this register the "Slave IDE Timing Register", but in fact, - * it controls timing for both master and slave drives. - */ - drive_enables |= 0x4000; - - if (is_slave) { - drive_enables &= 0xc006; - if (pio > 1) - /* enable prefetch and IORDY sample-point */ - drive_enables |= 0x0060; - } else { - drive_enables &= 0xc060; - if (pio > 1) - /* enable prefetch and IORDY sample-point */ - drive_enables |= 0x0006; - } - - pci_write_config_word(dev, 0x40, drive_enables); - spin_unlock_irqrestore(&ide_lock, flags); -} - -static u8 it8172_dma_2_pio (u8 xfer_rate) -{ - switch(xfer_rate) { - case XFER_UDMA_5: - case XFER_UDMA_4: - case XFER_UDMA_3: - case XFER_UDMA_2: - case XFER_UDMA_1: - case XFER_UDMA_0: - case XFER_MW_DMA_2: - case XFER_PIO_4: - return 4; - case XFER_MW_DMA_1: - case XFER_PIO_3: - return 3; - case XFER_SW_DMA_2: - case XFER_PIO_2: - return 2; - case XFER_MW_DMA_0: - case XFER_SW_DMA_1: - case XFER_SW_DMA_0: - case XFER_PIO_1: - case XFER_PIO_0: - case XFER_PIO_SLOW: - default: - return 0; - } -} - -static int it8172_tune_chipset (ide_drive_t *drive, u8 xferspeed) -{ - ide_hwif_t *hwif = HWIF(drive); - struct pci_dev *dev = hwif->pci_dev; - u8 speed = ide_rate_filter(it8172_ratemask(drive), xferspeed); - int a_speed = 3 << (drive->dn * 4); - int u_flag = 1 << drive->dn; - int u_speed = 0; - u8 reg48, reg4a; - - pci_read_config_byte(dev, 0x48, ®48); - pci_read_config_byte(dev, 0x4a, ®4a); - - /* - * Setting the DMA cycle time to 2 or 3 PCI clocks (60 and 91 nsec - * at 33 MHz PCI clock) seems to cause BadCRC errors during DMA - * transfers on some drives, even though both numbers meet the minimum - * ATAPI-4 spec of 73 and 54 nsec for UDMA 1 and 2 respectively. - * So the faster times are just commented out here. The good news is - * that the slower cycle time has very little affect on transfer - * performance. - */ - - switch(speed) { - case XFER_UDMA_4: - case XFER_UDMA_2: //u_speed = 2 << (drive->dn * 4); break; - case XFER_UDMA_5: - case XFER_UDMA_3: - case XFER_UDMA_1: //u_speed = 1 << (drive->dn * 4); break; - case XFER_UDMA_0: u_speed = 0 << (drive->dn * 4); break; - case XFER_MW_DMA_2: - case XFER_MW_DMA_1: - case XFER_MW_DMA_0: - case XFER_SW_DMA_2: break; - case XFER_PIO_4: - case XFER_PIO_3: - case XFER_PIO_2: - case XFER_PIO_0: break; - default: return -1; - } - - if (speed >= XFER_UDMA_0) { - pci_write_config_byte(dev, 0x48, reg48 | u_flag); - reg4a &= ~a_speed; - pci_write_config_byte(dev, 0x4a, reg4a | u_speed); - } else { - pci_write_config_byte(dev, 0x48, reg48 & ~u_flag); - pci_write_config_byte(dev, 0x4a, reg4a & ~a_speed); - } - - it8172_tune_drive(drive, it8172_dma_2_pio(speed)); - return (ide_config_drive_speed(drive, speed)); -} - -static int it8172_config_chipset_for_dma (ide_drive_t *drive) -{ - u8 speed = ide_dma_speed(drive, it8172_ratemask(drive)); - - if (!(speed)) { - u8 tspeed = ide_get_best_pio_mode(drive, 255, 4, NULL); - speed = it8172_dma_2_pio(XFER_PIO_0 + tspeed); - } - - (void) it8172_tune_chipset(drive, speed); - return ide_dma_enable(drive); -} - -static int it8172_config_drive_xfer_rate (ide_drive_t *drive) -{ - ide_hwif_t *hwif = HWIF(drive); - struct hd_driveid *id = drive->id; - - drive->init_speed = 0; - - if (id && (id->capability & 1) && drive->autodma) { - - if (ide_use_dma(drive)) { - if (it8172_config_chipset_for_dma(drive)) - return hwif->ide_dma_on(drive); - } - - goto fast_ata_pio; - - } else if ((id->capability & 8) || (id->field_valid & 2)) { -fast_ata_pio: - it8172_tune_drive(drive, 5); - return hwif->ide_dma_off_quietly(drive); - } - /* IORDY not supported */ - return 0; -} - -static unsigned int __devinit init_chipset_it8172 (struct pci_dev *dev, const char *name) -{ - unsigned char progif; - - /* - * Place both IDE interfaces into PCI "native" mode - */ - pci_read_config_byte(dev, PCI_CLASS_PROG, &progif); - pci_write_config_byte(dev, PCI_CLASS_PROG, progif | 0x05); - - return IT8172_IDE_IRQ; -} - - -static void __devinit init_hwif_it8172 (ide_hwif_t *hwif) -{ - struct pci_dev* dev = hwif->pci_dev; - unsigned long cmdBase, ctrlBase; - - hwif->autodma = 0; - hwif->tuneproc = &it8172_tune_drive; - hwif->speedproc = &it8172_tune_chipset; - - cmdBase = dev->resource[0].start; - ctrlBase = dev->resource[1].start; - - ide_init_hwif_ports(&hwif->hw, cmdBase, ctrlBase | 2, NULL); - memcpy(hwif->io_ports, hwif->hw.io_ports, sizeof(hwif->io_ports)); - hwif->noprobe = 0; - - if (!hwif->dma_base) { - hwif->drives[0].autotune = 1; - hwif->drives[1].autotune = 1; - return; - } - - hwif->atapi_dma = 1; - hwif->ultra_mask = 0x07; - hwif->mwdma_mask = 0x06; - hwif->swdma_mask = 0x04; - - hwif->ide_dma_check = &it8172_config_drive_xfer_rate; - if (!noautodma) - hwif->autodma = 1; - hwif->drives[0].autodma = hwif->autodma; - hwif->drives[1].autodma = hwif->autodma; -} - -static ide_pci_device_t it8172_chipsets[] __devinitdata = { - { /* 0 */ - .name = "IT8172G", - .init_chipset = init_chipset_it8172, - .init_hwif = init_hwif_it8172, - .channels = 2, - .autodma = AUTODMA, - .enablebits = {{0x00,0x00,0x00}, {0x40,0x00,0x01}}, - .bootable = ON_BOARD, - } -}; - -static int __devinit it8172_init_one(struct pci_dev *dev, const struct pci_device_id *id) -{ - if ((!(PCI_FUNC(dev->devfn) & 1) || - (!((dev->class >> 8) == PCI_CLASS_STORAGE_IDE)))) - return -ENODEV; /* IT8172 is more than an IDE controller */ - return ide_setup_pci_device(dev, &it8172_chipsets[id->driver_data]); -} - -static struct pci_device_id it8172_pci_tbl[] = { - { PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_IT8172G, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, - { 0, }, -}; -MODULE_DEVICE_TABLE(pci, it8172_pci_tbl); - -static struct pci_driver driver = { - .name = "IT8172_IDE", - .id_table = it8172_pci_tbl, - .probe = it8172_init_one, -}; - -static int it8172_ide_init(void) -{ - return ide_pci_register_driver(&driver); -} - -module_init(it8172_ide_init); - -MODULE_AUTHOR("SteveL@mvista.com"); -MODULE_DESCRIPTION("PCI driver module for ITE 8172 IDE"); -MODULE_LICENSE("GPL"); |