summaryrefslogtreecommitdiffstats
path: root/drivers/ide
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/ide')
-rw-r--r--drivers/ide/Kconfig10
-rw-r--r--drivers/ide/ide-cd.c89
-rw-r--r--drivers/ide/ide-disk.c7
-rw-r--r--drivers/ide/ide-dma.c1
-rw-r--r--drivers/ide/ide-floppy.c6
-rw-r--r--drivers/ide/ide-iops.c3
-rw-r--r--drivers/ide/ide-probe.c8
-rw-r--r--drivers/ide/legacy/hd.c4
-rw-r--r--drivers/ide/legacy/ide-cs.c35
-rw-r--r--drivers/ide/pci/Makefile1
-rw-r--r--drivers/ide/pci/generic.c73
-rw-r--r--drivers/ide/pci/hpt366.c470
-rw-r--r--drivers/ide/pci/it821x.c812
-rw-r--r--drivers/ide/pci/serverworks.c10
-rw-r--r--drivers/ide/pci/sgiioc4.c30
-rw-r--r--drivers/ide/ppc/pmac.c8
16 files changed, 1237 insertions, 330 deletions
diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig
index 3ac0a535b4a..5f33df47aa7 100644
--- a/drivers/ide/Kconfig
+++ b/drivers/ide/Kconfig
@@ -606,6 +606,12 @@ config BLK_DEV_IT8172
<http://www.ite.com.tw/ia/brief_it8172bsp.htm>; picture of the
board at <http://www.mvista.com/partners/semiconductor/ite.html>.
+config BLK_DEV_IT821X
+ tristate "IT821X IDE support"
+ help
+ This driver adds support for the ITE 8211 IDE controller and the
+ IT 8212 IDE RAID controller in both RAID and pass-through mode.
+
config BLK_DEV_NS87415
tristate "NS87415 chipset support"
help
@@ -672,8 +678,8 @@ config BLK_DEV_SVWKS
chipsets.
config BLK_DEV_SGIIOC4
- tristate "Silicon Graphics IOC4 chipset support"
- depends on IA64_SGI_SN2 || IA64_GENERIC
+ tristate "Silicon Graphics IOC4 chipset ATA/ATAPI support"
+ depends on (IA64_SGI_SN2 || IA64_GENERIC) && SGI_IOC4
help
This driver adds PIO & MultiMode DMA-2 support for the SGI IOC4
chipset, which has one channel and can support two devices.
diff --git a/drivers/ide/ide-cd.c b/drivers/ide/ide-cd.c
index 39f3e9101ed..0a31cfda08a 100644
--- a/drivers/ide/ide-cd.c
+++ b/drivers/ide/ide-cd.c
@@ -2657,16 +2657,63 @@ int ide_cdrom_lock_door (struct cdrom_device_info *cdi, int lock)
}
static
+int ide_cdrom_get_capabilities(ide_drive_t *drive, struct atapi_capabilities_page *cap)
+{
+ struct cdrom_info *info = drive->driver_data;
+ struct cdrom_device_info *cdi = &info->devinfo;
+ struct packet_command cgc;
+ int stat, attempts = 3, size = sizeof(*cap);
+
+ /*
+ * ACER50 (and others?) require the full spec length mode sense
+ * page capabilities size, but older drives break.
+ */
+ if (!(!strcmp(drive->id->model, "ATAPI CD ROM DRIVE 50X MAX") ||
+ !strcmp(drive->id->model, "WPI CDS-32X")))
+ size -= sizeof(cap->pad);
+
+ init_cdrom_command(&cgc, cap, size, CGC_DATA_UNKNOWN);
+ do { /* we seem to get stat=0x01,err=0x00 the first time (??) */
+ stat = cdrom_mode_sense(cdi, &cgc, GPMODE_CAPABILITIES_PAGE, 0);
+ if (!stat)
+ break;
+ } while (--attempts);
+ return stat;
+}
+
+static
+void ide_cdrom_update_speed (ide_drive_t *drive, struct atapi_capabilities_page *cap)
+{
+ /* The ACER/AOpen 24X cdrom has the speed fields byte-swapped */
+ if (!drive->id->model[0] &&
+ !strncmp(drive->id->fw_rev, "241N", 4)) {
+ CDROM_STATE_FLAGS(drive)->current_speed =
+ (((unsigned int)cap->curspeed) + (176/2)) / 176;
+ CDROM_CONFIG_FLAGS(drive)->max_speed =
+ (((unsigned int)cap->maxspeed) + (176/2)) / 176;
+ } else {
+ CDROM_STATE_FLAGS(drive)->current_speed =
+ (ntohs(cap->curspeed) + (176/2)) / 176;
+ CDROM_CONFIG_FLAGS(drive)->max_speed =
+ (ntohs(cap->maxspeed) + (176/2)) / 176;
+ }
+}
+
+static
int ide_cdrom_select_speed (struct cdrom_device_info *cdi, int speed)
{
ide_drive_t *drive = (ide_drive_t*) cdi->handle;
struct request_sense sense;
+ struct atapi_capabilities_page cap;
int stat;
if ((stat = cdrom_select_speed(drive, speed, &sense)) < 0)
return stat;
- cdi->speed = CDROM_STATE_FLAGS(drive)->current_speed;
+ if (!ide_cdrom_get_capabilities(drive, &cap)) {
+ ide_cdrom_update_speed(drive, &cap);
+ cdi->speed = CDROM_STATE_FLAGS(drive)->current_speed;
+ }
return 0;
}
@@ -2869,31 +2916,6 @@ static int ide_cdrom_register (ide_drive_t *drive, int nslots)
}
static
-int ide_cdrom_get_capabilities(ide_drive_t *drive, struct atapi_capabilities_page *cap)
-{
- struct cdrom_info *info = drive->driver_data;
- struct cdrom_device_info *cdi = &info->devinfo;
- struct packet_command cgc;
- int stat, attempts = 3, size = sizeof(*cap);
-
- /*
- * ACER50 (and others?) require the full spec length mode sense
- * page capabilities size, but older drives break.
- */
- if (!(!strcmp(drive->id->model, "ATAPI CD ROM DRIVE 50X MAX") ||
- !strcmp(drive->id->model, "WPI CDS-32X")))
- size -= sizeof(cap->pad);
-
- init_cdrom_command(&cgc, cap, size, CGC_DATA_UNKNOWN);
- do { /* we seem to get stat=0x01,err=0x00 the first time (??) */
- stat = cdrom_mode_sense(cdi, &cgc, GPMODE_CAPABILITIES_PAGE, 0);
- if (!stat)
- break;
- } while (--attempts);
- return stat;
-}
-
-static
int ide_cdrom_probe_capabilities (ide_drive_t *drive)
{
struct cdrom_info *info = drive->driver_data;
@@ -2978,20 +3000,7 @@ int ide_cdrom_probe_capabilities (ide_drive_t *drive)
}
}
- /* The ACER/AOpen 24X cdrom has the speed fields byte-swapped */
- if (!drive->id->model[0] &&
- !strncmp(drive->id->fw_rev, "241N", 4)) {
- CDROM_STATE_FLAGS(drive)->current_speed =
- (((unsigned int)cap.curspeed) + (176/2)) / 176;
- CDROM_CONFIG_FLAGS(drive)->max_speed =
- (((unsigned int)cap.maxspeed) + (176/2)) / 176;
- } else {
- CDROM_STATE_FLAGS(drive)->current_speed =
- (ntohs(cap.curspeed) + (176/2)) / 176;
- CDROM_CONFIG_FLAGS(drive)->max_speed =
- (ntohs(cap.maxspeed) + (176/2)) / 176;
- }
-
+ ide_cdrom_update_speed(drive, &cap);
/* don't print speed if the drive reported 0.
*/
printk(KERN_INFO "%s: ATAPI", drive->name);
diff --git a/drivers/ide/ide-disk.c b/drivers/ide/ide-disk.c
index 3302cd8eab4..f9c1acb4ed6 100644
--- a/drivers/ide/ide-disk.c
+++ b/drivers/ide/ide-disk.c
@@ -119,6 +119,10 @@ static int lba_capacity_is_ok (struct hd_driveid *id)
{
unsigned long lba_sects, chs_sects, head, tail;
+ /* No non-LBA info .. so valid! */
+ if (id->cyls == 0)
+ return 1;
+
/*
* The ATA spec tells large drives to return
* C/H/S = 16383/16/63 independent of their size.
@@ -1215,7 +1219,8 @@ static int ide_disk_probe(struct device *dev)
if (!idkp)
goto failed;
- g = alloc_disk(1 << PARTN_BITS);
+ g = alloc_disk_node(1 << PARTN_BITS,
+ pcibus_to_node(drive->hwif->pci_dev->bus));
if (!g)
goto out_free_idkp;
diff --git a/drivers/ide/ide-dma.c b/drivers/ide/ide-dma.c
index 2d2eefb610d..1e1531334c2 100644
--- a/drivers/ide/ide-dma.c
+++ b/drivers/ide/ide-dma.c
@@ -132,7 +132,6 @@ static const struct drive_list_entry drive_blacklist [] = {
{ "SAMSUNG CD-ROM SC-148C", "ALL" },
{ "SAMSUNG CD-ROM SC", "ALL" },
{ "SanDisk SDP3B-64" , "ALL" },
- { "SAMSUNG CD-ROM SN-124", "ALL" },
{ "ATAPI CD-ROM DRIVE 40X MAXIMUM", "ALL" },
{ "_NEC DV5800A", "ALL" },
{ NULL , NULL }
diff --git a/drivers/ide/ide-floppy.c b/drivers/ide/ide-floppy.c
index c949e98df4b..9eab6426148 100644
--- a/drivers/ide/ide-floppy.c
+++ b/drivers/ide/ide-floppy.c
@@ -661,10 +661,12 @@ static void idefloppy_output_buffers (ide_drive_t *drive, idefloppy_pc_t *pc, un
idefloppy_do_end_request(drive, 1, done >> 9);
+#if IDEFLOPPY_DEBUG_BUGS
if (bcount) {
printk(KERN_ERR "%s: leftover data in idefloppy_output_buffers, bcount == %d\n", drive->name, bcount);
idefloppy_write_zeros(drive, bcount);
}
+#endif
}
static void idefloppy_update_buffers (ide_drive_t *drive, idefloppy_pc_t *pc)
@@ -1048,6 +1050,9 @@ static ide_startstop_t idefloppy_issue_pc (ide_drive_t *drive, idefloppy_pc_t *p
atapi_bcount_t bcount;
ide_handler_t *pkt_xfer_routine;
+#if 0 /* Accessing floppy->pc is not valid here, the previous pc may be gone
+ and have lived on another thread's stack; that stack may have become
+ unmapped meanwhile (CONFIG_DEBUG_PAGEALLOC). */
#if IDEFLOPPY_DEBUG_BUGS
if (floppy->pc->c[0] == IDEFLOPPY_REQUEST_SENSE_CMD &&
pc->c[0] == IDEFLOPPY_REQUEST_SENSE_CMD) {
@@ -1055,6 +1060,7 @@ static ide_startstop_t idefloppy_issue_pc (ide_drive_t *drive, idefloppy_pc_t *p
"Two request sense in serial were issued\n");
}
#endif /* IDEFLOPPY_DEBUG_BUGS */
+#endif
if (floppy->failed_pc == NULL &&
pc->c[0] != IDEFLOPPY_REQUEST_SENSE_CMD)
diff --git a/drivers/ide/ide-iops.c b/drivers/ide/ide-iops.c
index 53024942a7e..b443b04a4c5 100644
--- a/drivers/ide/ide-iops.c
+++ b/drivers/ide/ide-iops.c
@@ -1181,7 +1181,8 @@ static ide_startstop_t do_reset1 (ide_drive_t *drive, int do_not_try_atapi)
pre_reset(drive);
SELECT_DRIVE(drive);
udelay (20);
- hwif->OUTB(WIN_SRST, IDE_COMMAND_REG);
+ hwif->OUTBSYNC(drive, WIN_SRST, IDE_COMMAND_REG);
+ ndelay(400);
hwgroup->poll_timeout = jiffies + WAIT_WORSTCASE;
hwgroup->polling = 1;
__ide_set_handler(drive, &atapi_reset_pollfunc, HZ/20, NULL);
diff --git a/drivers/ide/ide-probe.c b/drivers/ide/ide-probe.c
index 5d876f53c69..7df85af7537 100644
--- a/drivers/ide/ide-probe.c
+++ b/drivers/ide/ide-probe.c
@@ -977,8 +977,9 @@ static int ide_init_queue(ide_drive_t *drive)
* limits and LBA48 we could raise it but as yet
* do not.
*/
-
- q = blk_init_queue(do_ide_request, &ide_lock);
+
+ q = blk_init_queue_node(do_ide_request, &ide_lock,
+ pcibus_to_node(drive->hwif->pci_dev->bus));
if (!q)
return 1;
@@ -1095,7 +1096,8 @@ static int init_irq (ide_hwif_t *hwif)
hwgroup->hwif->next = hwif;
spin_unlock_irq(&ide_lock);
} else {
- hwgroup = kmalloc(sizeof(ide_hwgroup_t),GFP_KERNEL);
+ hwgroup = kmalloc_node(sizeof(ide_hwgroup_t), GFP_KERNEL,
+ pcibus_to_node(hwif->drives[0].hwif->pci_dev->bus));
if (!hwgroup)
goto out_up;
diff --git a/drivers/ide/legacy/hd.c b/drivers/ide/legacy/hd.c
index e884cd4b22f..242029c9c0c 100644
--- a/drivers/ide/legacy/hd.c
+++ b/drivers/ide/legacy/hd.c
@@ -156,11 +156,13 @@ else \
#if (HD_DELAY > 0)
+
+#include <asm/i8253.h>
+
unsigned long last_req;
unsigned long read_timer(void)
{
- extern spinlock_t i8253_lock;
unsigned long t, flags;
int i;
diff --git a/drivers/ide/legacy/ide-cs.c b/drivers/ide/legacy/ide-cs.c
index e20327e54b1..978d27d6452 100644
--- a/drivers/ide/legacy/ide-cs.c
+++ b/drivers/ide/legacy/ide-cs.c
@@ -457,6 +457,40 @@ int ide_event(event_t event, int priority,
return 0;
} /* ide_event */
+static struct pcmcia_device_id ide_ids[] = {
+ PCMCIA_DEVICE_FUNC_ID(4),
+ PCMCIA_DEVICE_MANF_CARD(0x0032, 0x0704),
+ PCMCIA_DEVICE_MANF_CARD(0x00a4, 0x002d),
+ PCMCIA_DEVICE_MANF_CARD(0x2080, 0x0001),
+ PCMCIA_DEVICE_MANF_CARD(0x0045, 0x0401),
+ PCMCIA_DEVICE_PROD_ID123("Caravelle", "PSC-IDE ", "PSC000", 0x8c36137c, 0xd0693ab8, 0x2768a9f0),
+ PCMCIA_DEVICE_PROD_ID123("CDROM", "IDE", "MCD-601p", 0x1b9179ca, 0xede88951, 0x0d902f74),
+ PCMCIA_DEVICE_PROD_ID123("PCMCIA", "IDE CARD", "F1", 0x281f1c5d, 0x1907960c, 0xf7fde8b9),
+ PCMCIA_DEVICE_PROD_ID12("ARGOSY", "CD-ROM", 0x78f308dc, 0x66536591),
+ PCMCIA_DEVICE_PROD_ID12("ARGOSY", "PnPIDE", 0x78f308dc, 0x0c694728),
+ PCMCIA_DEVICE_PROD_ID12("CNF CD-M", "CD-ROM", 0x7d93b852, 0x66536591),
+ PCMCIA_DEVICE_PROD_ID12("Creative Technology Ltd.", "PCMCIA CD-ROM Interface Card", 0xff8c8a45, 0xfe8020c4),
+ PCMCIA_DEVICE_PROD_ID12("Digital Equipment Corporation.", "Digital Mobile Media CD-ROM", 0x17692a66, 0xef1dcbde),
+ PCMCIA_DEVICE_PROD_ID12("EXP", "CD", 0x6f58c983, 0xaae5994f),
+ PCMCIA_DEVICE_PROD_ID12("EXP ", "CD-ROM", 0x0a5c52fd, 0x66536591),
+ PCMCIA_DEVICE_PROD_ID12("EXP ", "PnPIDE", 0x0a5c52fd, 0x0c694728),
+ PCMCIA_DEVICE_PROD_ID12("FREECOM", "PCCARD-IDE", 0x5714cbf7, 0x48e0ab8e),
+ PCMCIA_DEVICE_PROD_ID12("IBM", "IBM17JSSFP20", 0xb569a6e5, 0xf2508753),
+ PCMCIA_DEVICE_PROD_ID12("IO DATA", "CBIDE2 ", 0x547e66dc, 0x8671043b),
+ PCMCIA_DEVICE_PROD_ID12("IO DATA", "PCIDE", 0x547e66dc, 0x5c5ab149),
+ PCMCIA_DEVICE_PROD_ID12("IO DATA", "PCIDEII", 0x547e66dc, 0xb3662674),
+ PCMCIA_DEVICE_PROD_ID12("LOOKMEET", "CBIDE2 ", 0xe37be2b5, 0x8671043b),
+ PCMCIA_DEVICE_PROD_ID12(" ", "NinjaATA-", 0x3b6e20c8, 0xebe0bd79),
+ PCMCIA_DEVICE_PROD_ID12("PCMCIA", "CD-ROM", 0x281f1c5d, 0x66536591),
+ PCMCIA_DEVICE_PROD_ID12("PCMCIA", "PnPIDE", 0x281f1c5d, 0x0c694728),
+ PCMCIA_DEVICE_PROD_ID12("SHUTTLE TECHNOLOGY LTD.", "PCCARD-IDE/ATAPI Adapter", 0x4a3f0ba0, 0x322560e1),
+ PCMCIA_DEVICE_PROD_ID12("TOSHIBA", "MK2001MPL", 0xb4585a1a, 0x3489e003),
+ PCMCIA_DEVICE_PROD_ID12("WIT", "IDE16", 0x244e5994, 0x3e232852),
+ PCMCIA_DEVICE_PROD_ID1("STI Flash", 0xe4a13209),
+ PCMCIA_DEVICE_NULL,
+};
+MODULE_DEVICE_TABLE(pcmcia, ide_ids);
+
static struct pcmcia_driver ide_cs_driver = {
.owner = THIS_MODULE,
.drv = {
@@ -464,6 +498,7 @@ static struct pcmcia_driver ide_cs_driver = {
},
.attach = ide_attach,
.detach = ide_detach,
+ .id_table = ide_ids,
};
static int __init init_ide_cs(void)
diff --git a/drivers/ide/pci/Makefile b/drivers/ide/pci/Makefile
index 55e6e553e49..af46226c179 100644
--- a/drivers/ide/pci/Makefile
+++ b/drivers/ide/pci/Makefile
@@ -12,6 +12,7 @@ obj-$(CONFIG_BLK_DEV_HPT34X) += hpt34x.o
obj-$(CONFIG_BLK_DEV_HPT366) += hpt366.o
#obj-$(CONFIG_BLK_DEV_HPT37X) += hpt37x.o
obj-$(CONFIG_BLK_DEV_IT8172) += it8172.o
+obj-$(CONFIG_BLK_DEV_IT821X) += it821x.o
obj-$(CONFIG_BLK_DEV_NS87415) += ns87415.o
obj-$(CONFIG_BLK_DEV_OPTI621) += opti621.o
obj-$(CONFIG_BLK_DEV_PDC202XX_OLD) += pdc202xx_old.o
diff --git a/drivers/ide/pci/generic.c b/drivers/ide/pci/generic.c
index 4565cc311ff..da46577380f 100644
--- a/drivers/ide/pci/generic.c
+++ b/drivers/ide/pci/generic.c
@@ -39,6 +39,17 @@
#include <asm/io.h>
+static int ide_generic_all; /* Set to claim all devices */
+
+static int __init ide_generic_all_on(char *unused)
+{
+ ide_generic_all = 1;
+ printk(KERN_INFO "IDE generic will claim all unknown PCI IDE storage controllers.\n");
+ return 1;
+}
+
+__setup("all-generic-ide", ide_generic_all_on);
+
static void __devinit init_hwif_generic (ide_hwif_t *hwif)
{
switch(hwif->pci_dev->device) {
@@ -78,79 +89,85 @@ static void __devinit init_hwif_generic (ide_hwif_t *hwif)
static ide_pci_device_t generic_chipsets[] __devinitdata = {
{ /* 0 */
+ .name = "Unknown",
+ .init_hwif = init_hwif_generic,
+ .channels = 2,
+ .autodma = AUTODMA,
+ .bootable = ON_BOARD,
+ },{ /* 1 */
.name = "NS87410",
.init_hwif = init_hwif_generic,
.channels = 2,
.autodma = AUTODMA,
.enablebits = {{0x43,0x08,0x08}, {0x47,0x08,0x08}},
.bootable = ON_BOARD,
- },{ /* 1 */
+ },{ /* 2 */
.name = "SAMURAI",
.init_hwif = init_hwif_generic,
.channels = 2,
.autodma = AUTODMA,
.bootable = ON_BOARD,
- },{ /* 2 */
+ },{ /* 3 */
.name = "HT6565",
.init_hwif = init_hwif_generic,
.channels = 2,
.autodma = AUTODMA,
.bootable = ON_BOARD,
- },{ /* 3 */
+ },{ /* 4 */
.name = "UM8673F",
.init_hwif = init_hwif_generic,
.channels = 2,
.autodma = NODMA,
.bootable = ON_BOARD,
- },{ /* 4 */
+ },{ /* 5 */
.name = "UM8886A",
.init_hwif = init_hwif_generic,
.channels = 2,
.autodma = NODMA,
.bootable = ON_BOARD,
- },{ /* 5 */
+ },{ /* 6 */
.name = "UM8886BF",
.init_hwif = init_hwif_generic,
.channels = 2,
.autodma = NODMA,
.bootable = ON_BOARD,
- },{ /* 6 */
+ },{ /* 7 */
.name = "HINT_IDE",
.init_hwif = init_hwif_generic,
.channels = 2,
.autodma = AUTODMA,
.bootable = ON_BOARD,
- },{ /* 7 */
+ },{ /* 8 */
.name = "VIA_IDE",
.init_hwif = init_hwif_generic,
.channels = 2,
.autodma = NOAUTODMA,
.bootable = ON_BOARD,
- },{ /* 8 */
+ },{ /* 9 */
.name = "OPTI621V",
.init_hwif = init_hwif_generic,
.channels = 2,
.autodma = NOAUTODMA,
.bootable = ON_BOARD,
- },{ /* 9 */
+ },{ /* 10 */
.name = "VIA8237SATA",
.init_hwif = init_hwif_generic,
.channels = 2,
.autodma = AUTODMA,
.bootable = OFF_BOARD,
- },{ /* 10 */
+ },{ /* 11 */
.name = "Piccolo0102",
.init_hwif = init_hwif_generic,
.channels = 2,
.autodma = NOAUTODMA,
.bootable = ON_BOARD,
- },{ /* 11 */
+ },{ /* 12 */
.name = "Piccolo0103",
.init_hwif = init_hwif_generic,
.channels = 2,
.autodma = NOAUTODMA,
.bootable = ON_BOARD,
- },{ /* 12 */
+ },{ /* 13 */
.name = "Piccolo0105",
.init_hwif = init_hwif_generic,
.channels = 2,
@@ -174,6 +191,10 @@ static int __devinit generic_init_one(struct pci_dev *dev, const struct pci_devi
u16 command;
int ret = -ENODEV;
+ /* Don't use the generic entry unless instructed to do so */
+ if (id->driver_data == 0 && ide_generic_all == 0)
+ goto out;
+
if (dev->vendor == PCI_VENDOR_ID_UMC &&
dev->device == PCI_DEVICE_ID_UMC_UM8886A &&
(!(PCI_FUNC(dev->devfn) & 1)))
@@ -195,21 +216,23 @@ out:
}
static struct pci_device_id generic_pci_tbl[] = {
- { PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_87410, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
- { PCI_VENDOR_ID_PCTECH, PCI_DEVICE_ID_PCTECH_SAMURAI_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
- { PCI_VENDOR_ID_HOLTEK, PCI_DEVICE_ID_HOLTEK_6565, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2},
- { PCI_VENDOR_ID_UMC, PCI_DEVICE_ID_UMC_UM8673F, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 3},
- { PCI_VENDOR_ID_UMC, PCI_DEVICE_ID_UMC_UM8886A, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4},
- { PCI_VENDOR_ID_UMC, PCI_DEVICE_ID_UMC_UM8886BF, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 5},
- { PCI_VENDOR_ID_HINT, PCI_DEVICE_ID_HINT_VXPROII_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 6},
- { PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C561, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 7},
- { PCI_VENDOR_ID_OPTI, PCI_DEVICE_ID_OPTI_82C558, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8},
+ { PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_87410, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 1},
+ { PCI_VENDOR_ID_PCTECH, PCI_DEVICE_ID_PCTECH_SAMURAI_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 2},
+ { PCI_VENDOR_ID_HOLTEK, PCI_DEVICE_ID_HOLTEK_6565, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 3},
+ { PCI_VENDOR_ID_UMC, PCI_DEVICE_ID_UMC_UM8673F, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4},
+ { PCI_VENDOR_ID_UMC, PCI_DEVICE_ID_UMC_UM8886A, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 5},
+ { PCI_VENDOR_ID_UMC, PCI_DEVICE_ID_UMC_UM8886BF, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 6},
+ { PCI_VENDOR_ID_HINT, PCI_DEVICE_ID_HINT_VXPROII_IDE, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 7},
+ { PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C561, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 8},
+ { PCI_VENDOR_ID_OPTI, PCI_DEVICE_ID_OPTI_82C558, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 9},
#ifdef CONFIG_BLK_DEV_IDE_SATA
- { PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237_SATA, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 9},
+ { PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237_SATA, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 10},
#endif
- { PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 10},
- { PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 11},
- { PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_2, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 12},
+ { PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 11},
+ { PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 12},
+ { PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_2, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 13},
+ /* Must come last. If you add entries adjust this table appropriately and the init_one code */
+ { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_STORAGE_IDE << 8, 0xFFFFFF00UL, 0},
{ 0, },
};
MODULE_DEVICE_TABLE(pci, generic_pci_tbl);
diff --git a/drivers/ide/pci/hpt366.c b/drivers/ide/pci/hpt366.c
index c8ee0b8c029..7b64db10d1b 100644
--- a/drivers/ide/pci/hpt366.c
+++ b/drivers/ide/pci/hpt366.c
@@ -10,6 +10,11 @@
* donation of an ABit BP6 mainboard, processor, and memory acellerated
* development and support.
*
+ *
+ * Highpoint have their own driver (source except for the raid part)
+ * available from http://www.highpoint-tech.com/hpt3xx-opensource-v131.tgz
+ * This may be useful to anyone wanting to work on the mainstream hpt IDE.
+ *
* Note that final HPT370 support was done by force extraction of GPL.
*
* - add function for getting/setting power status of drive
@@ -446,44 +451,29 @@ static struct chipset_bus_clock_list_entry sixty_six_base_hpt374[] = {
#define F_LOW_PCI_50 0x2d
#define F_LOW_PCI_66 0x42
-/* FIXME: compare with driver's code before removing */
-#if 0
- if (hpt_minimum_revision(dev, 3)) {
- u8 cbl;
- cbl = inb(iobase + 0x7b);
- outb(cbl | 1, iobase + 0x7b);
- outb(cbl & ~1, iobase + 0x7b);
- cbl = inb(iobase + 0x7a);
- p += sprintf(p, "Cable: ATA-%d"
- " ATA-%d\n",
- (cbl & 0x02) ? 33 : 66,
- (cbl & 0x01) ? 33 : 66);
- p += sprintf(p, "\n");
- }
- {
- u8 c2, c3;
- /* older revs don't have these registers mapped
- * into io space */
- pci_read_config_byte(dev, 0x43, &c0);
- pci_read_config_byte(dev, 0x47, &c1);
- pci_read_config_byte(dev, 0x4b, &c2);
- pci_read_config_byte(dev, 0x4f, &c3);
-
- p += sprintf(p, "Mode: %s %s"
- " %s %s\n",
- (c0 & 0x10) ? "UDMA" : (c0 & 0x20) ? "DMA " :
- (c0 & 0x80) ? "PIO " : "off ",
- (c1 & 0x10) ? "UDMA" : (c1 & 0x20) ? "DMA " :
- (c1 & 0x80) ? "PIO " : "off ",
- (c2 & 0x10) ? "UDMA" : (c2 & 0x20) ? "DMA " :
- (c2 & 0x80) ? "PIO " : "off ",
- (c3 & 0x10) ? "UDMA" : (c3 & 0x20) ? "DMA " :
- (c3 & 0x80) ? "PIO " : "off ");
- }
- }
-#endif
+/*
+ * Hold all the highpoint quirks and revision information in one
+ * place.
+ */
-static u32 hpt_revision (struct pci_dev *dev)
+struct hpt_info
+{
+ u8 max_mode; /* Speeds allowed */
+ int revision; /* Chipset revision */
+ int flags; /* Chipset properties */
+#define PLL_MODE 1
+#define IS_372N 2
+ /* Speed table */
+ struct chipset_bus_clock_list_entry *speed;
+};
+
+/*
+ * This wants fixing so that we do everything not by classrev
+ * (which breaks on the newest chips) but by creating an
+ * enumeration of chip variants and using that
+ */
+
+static __devinit u32 hpt_revision (struct pci_dev *dev)
{
u32 class_rev;
pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev);
@@ -507,37 +497,33 @@ static u32 hpt_revision (struct pci_dev *dev)
return class_rev;
}
-static u32 hpt_minimum_revision (struct pci_dev *dev, int revision)
-{
- unsigned int class_rev = hpt_revision(dev);
- revision--;
- return ((int) (class_rev > revision) ? 1 : 0);
-}
-
static int check_in_drive_lists(ide_drive_t *drive, const char **list);
static u8 hpt3xx_ratemask (ide_drive_t *drive)
{
- struct pci_dev *dev = HWIF(drive)->pci_dev;
+ ide_hwif_t *hwif = drive->hwif;
+ struct hpt_info *info = ide_get_hwifdata(hwif);
u8 mode = 0;
- if (hpt_minimum_revision(dev, 8)) { /* HPT374 */
+ /* FIXME: TODO - move this to set info->mode once at boot */
+
+ if (info->revision >= 8) { /* HPT374 */
mode = (HPT374_ALLOW_ATA133_6) ? 4 : 3;
- } else if (hpt_minimum_revision(dev, 7)) { /* HPT371 */
+ } else if (info->revision >= 7) { /* HPT371 */
mode = (HPT371_ALLOW_ATA133_6) ? 4 : 3;
- } else if (hpt_minimum_revision(dev, 6)) { /* HPT302 */
+ } else if (info->revision >= 6) { /* HPT302 */
mode = (HPT302_ALLOW_ATA133_6) ? 4 : 3;
- } else if (hpt_minimum_revision(dev, 5)) { /* HPT372 */
+ } else if (info->revision >= 5) { /* HPT372 */
mode = (HPT372_ALLOW_ATA133_6) ? 4 : 3;
- } else if (hpt_minimum_revision(dev, 4)) { /* HPT370A */
+ } else if (info->revision >= 4) { /* HPT370A */
mode = (HPT370_ALLOW_ATA100_5) ? 3 : 2;
- } else if (hpt_minimum_revision(dev, 3)) { /* HPT370 */
+ } else if (info->revision >= 3) { /* HPT370 */
mode = (HPT370_ALLOW_ATA100_5) ? 3 : 2;
mode = (check_in_drive_lists(drive, bad_ata33)) ? 0 : mode;
} else { /* HPT366 and HPT368 */
mode = (check_in_drive_lists(drive, bad_ata33)) ? 0 : 2;
}
- if (!eighty_ninty_three(drive) && (mode))
+ if (!eighty_ninty_three(drive) && mode)
mode = min(mode, (u8)1);
return mode;
}
@@ -549,7 +535,8 @@ static u8 hpt3xx_ratemask (ide_drive_t *drive)
static u8 hpt3xx_ratefilter (ide_drive_t *drive, u8 speed)
{
- struct pci_dev *dev = HWIF(drive)->pci_dev;
+ ide_hwif_t *hwif = drive->hwif;
+ struct hpt_info *info = ide_get_hwifdata(hwif);
u8 mode = hpt3xx_ratemask(drive);
if (drive->media != ide_disk)
@@ -561,7 +548,7 @@ static u8 hpt3xx_ratefilter (ide_drive_t *drive, u8 speed)
break;
case 0x03:
speed = min(speed, (u8)XFER_UDMA_5);
- if (hpt_minimum_revision(dev, 5))
+ if (info->revision >= 5)
break;
if (check_in_drive_lists(drive, bad_ata100_5))
speed = min(speed, (u8)XFER_UDMA_4);
@@ -571,7 +558,7 @@ static u8 hpt3xx_ratefilter (ide_drive_t *drive, u8 speed)
/*
* CHECK ME, Does this need to be set to 5 ??
*/
- if (hpt_minimum_revision(dev, 3))
+ if (info->revision >= 3)
break;
if ((check_in_drive_lists(drive, bad_ata66_4)) ||
(!(HPT366_ALLOW_ATA66_4)))
@@ -585,7 +572,7 @@ static u8 hpt3xx_ratefilter (ide_drive_t *drive, u8 speed)
/*
* CHECK ME, Does this need to be set to 5 ??
*/
- if (hpt_minimum_revision(dev, 3))
+ if (info->revision >= 3)
break;
if (check_in_drive_lists(drive, bad_ata33))
speed = min(speed, (u8)XFER_MW_DMA_2);
@@ -624,11 +611,12 @@ static unsigned int pci_bus_clock_list (u8 speed, struct chipset_bus_clock_list_
static int hpt36x_tune_chipset(ide_drive_t *drive, u8 xferspeed)
{
- struct pci_dev *dev = HWIF(drive)->pci_dev;
+ ide_hwif_t *hwif = drive->hwif;
+ struct pci_dev *dev = hwif->pci_dev;
+ struct hpt_info *info = ide_get_hwifdata(hwif);
u8 speed = hpt3xx_ratefilter(drive, xferspeed);
-// u8 speed = ide_rate_filter(hpt3xx_ratemask(drive), xferspeed);
u8 regtime = (drive->select.b.unit & 0x01) ? 0x44 : 0x40;
- u8 regfast = (HWIF(drive)->channel) ? 0x55 : 0x51;
+ u8 regfast = (hwif->channel) ? 0x55 : 0x51;
u8 drive_fast = 0;
u32 reg1 = 0, reg2 = 0;
@@ -636,16 +624,11 @@ static int hpt36x_tune_chipset(ide_drive_t *drive, u8 xferspeed)
* Disable the "fast interrupt" prediction.
*/
pci_read_config_byte(dev, regfast, &drive_fast);
-#if 0
- if (drive_fast & 0x02)
- pci_write_config_byte(dev, regfast, drive_fast & ~0x20);
-#else
if (drive_fast & 0x80)
pci_write_config_byte(dev, regfast, drive_fast & ~0x80);
-#endif
- reg2 = pci_bus_clock_list(speed,
- (struct chipset_bus_clock_list_entry *) pci_get_drvdata(dev));
+ reg2 = pci_bus_clock_list(speed, info->speed);
+
/*
* Disable on-chip PIO FIFO/buffer
* (to avoid problems handling I/O errors later)
@@ -665,10 +648,11 @@ static int hpt36x_tune_chipset(ide_drive_t *drive, u8 xferspeed)
static int hpt370_tune_chipset(ide_drive_t *drive, u8 xferspeed)
{
- struct pci_dev *dev = HWIF(drive)->pci_dev;
+ ide_hwif_t *hwif = drive->hwif;
+ struct pci_dev *dev = hwif->pci_dev;
+ struct hpt_info *info = ide_get_hwifdata(hwif);
u8 speed = hpt3xx_ratefilter(drive, xferspeed);
-// u8 speed = ide_rate_filter(hpt3xx_ratemask(drive), xferspeed);
- u8 regfast = (HWIF(drive)->channel) ? 0x55 : 0x51;
+ u8 regfast = (drive->hwif->channel) ? 0x55 : 0x51;
u8 drive_pci = 0x40 + (drive->dn * 4);
u8 new_fast = 0, drive_fast = 0;
u32 list_conf = 0, drive_conf = 0;
@@ -693,17 +677,13 @@ static int hpt370_tune_chipset(ide_drive_t *drive, u8 xferspeed)
if (new_fast != drive_fast)
pci_write_config_byte(dev, regfast, new_fast);
- list_conf = pci_bus_clock_list(speed,
- (struct chipset_bus_clock_list_entry *)
- pci_get_drvdata(dev));
+ list_conf = pci_bus_clock_list(speed, info->speed);
pci_read_config_dword(dev, drive_pci, &drive_conf);
list_conf = (list_conf & ~conf_mask) | (drive_conf & conf_mask);
- if (speed < XFER_MW_DMA_0) {
+ if (speed < XFER_MW_DMA_0)
list_conf &= ~0x80000000; /* Disable on-chip PIO FIFO/buffer */
- }
-
pci_write_config_dword(dev, drive_pci, list_conf);
return ide_config_drive_speed(drive, speed);
@@ -711,10 +691,11 @@ static int hpt370_tune_chipset(ide_drive_t *drive, u8 xferspeed)
static int hpt372_tune_chipset(ide_drive_t *drive, u8 xferspeed)
{
- struct pci_dev *dev = HWIF(drive)->pci_dev;
+ ide_hwif_t *hwif = drive->hwif;
+ struct pci_dev *dev = hwif->pci_dev;
+ struct hpt_info *info = ide_get_hwifdata(hwif);
u8 speed = hpt3xx_ratefilter(drive, xferspeed);
-// u8 speed = ide_rate_filter(hpt3xx_ratemask(drive), xferspeed);
- u8 regfast = (HWIF(drive)->channel) ? 0x55 : 0x51;
+ u8 regfast = (drive->hwif->channel) ? 0x55 : 0x51;
u8 drive_fast = 0, drive_pci = 0x40 + (drive->dn * 4);
u32 list_conf = 0, drive_conf = 0;
u32 conf_mask = (speed >= XFER_MW_DMA_0) ? 0xc0000000 : 0x30070000;
@@ -726,10 +707,8 @@ static int hpt372_tune_chipset(ide_drive_t *drive, u8 xferspeed)
pci_read_config_byte(dev, regfast, &drive_fast);
drive_fast &= ~0x07;
pci_write_config_byte(dev, regfast, drive_fast);
-
- list_conf = pci_bus_clock_list(speed,
- (struct chipset_bus_clock_list_entry *)
- pci_get_drvdata(dev));
+
+ list_conf = pci_bus_clock_list(speed, info->speed);
pci_read_config_dword(dev, drive_pci, &drive_conf);
list_conf = (list_conf & ~conf_mask) | (drive_conf & conf_mask);
if (speed < XFER_MW_DMA_0)
@@ -741,19 +720,14 @@ static int hpt372_tune_chipset(ide_drive_t *drive, u8 xferspeed)
static int hpt3xx_tune_chipset (ide_drive_t *drive, u8 speed)
{
- struct pci_dev *dev = HWIF(drive)->pci_dev;
+ ide_hwif_t *hwif = drive->hwif;
+ struct hpt_info *info = ide_get_hwifdata(hwif);
- if (hpt_minimum_revision(dev, 8))
+ if (info->revision >= 8)
return hpt372_tune_chipset(drive, speed); /* not a typo */
-#if 0
- else if (hpt_minimum_revision(dev, 7))
- hpt371_tune_chipset(drive, speed);
- else if (hpt_minimum_revision(dev, 6))
- hpt302_tune_chipset(drive, speed);
-#endif
- else if (hpt_minimum_revision(dev, 5))
+ else if (info->revision >= 5)
return hpt372_tune_chipset(drive, speed);
- else if (hpt_minimum_revision(dev, 3))
+ else if (info->revision >= 3)
return hpt370_tune_chipset(drive, speed);
else /* hpt368: hpt_minimum_revision(dev, 2) */
return hpt36x_tune_chipset(drive, speed);
@@ -779,8 +753,14 @@ static void hpt3xx_tune_drive (ide_drive_t *drive, u8 pio)
static int config_chipset_for_dma (ide_drive_t *drive)
{
u8 speed = ide_dma_speed(drive, hpt3xx_ratemask(drive));
+ ide_hwif_t *hwif = drive->hwif;
+ struct hpt_info *info = ide_get_hwifdata(hwif);
- if (!(speed))
+ if (!speed)
+ return 0;
+
+ /* If we don't have any timings we can't do a lot */
+ if (info->speed == NULL)
return 0;
(void) hpt3xx_tune_chipset(drive, speed);
@@ -794,7 +774,7 @@ static int hpt3xx_quirkproc (ide_drive_t *drive)
static void hpt3xx_intrproc (ide_drive_t *drive)
{
- ide_hwif_t *hwif = HWIF(drive);
+ ide_hwif_t *hwif = drive->hwif;
if (drive->quirk_list)
return;
@@ -804,24 +784,26 @@ static void hpt3xx_intrproc (ide_drive_t *drive)
static void hpt3xx_maskproc (ide_drive_t *drive, int mask)
{
- struct pci_dev *dev = HWIF(drive)->pci_dev;
+ ide_hwif_t *hwif = drive->hwif;
+ struct hpt_info *info = ide_get_hwifdata(hwif);
+ struct pci_dev *dev = hwif->pci_dev;
if (drive->quirk_list) {
- if (hpt_minimum_revision(dev,3)) {
+ if (info->revision >= 3) {
u8 reg5a = 0;
pci_read_config_byte(dev, 0x5a, &reg5a);
if (((reg5a & 0x10) >> 4) != mask)
pci_write_config_byte(dev, 0x5a, mask ? (reg5a | 0x10) : (reg5a & ~0x10));
} else {
if (mask) {
- disable_irq(HWIF(drive)->irq);
+ disable_irq(hwif->irq);
} else {
- enable_irq(HWIF(drive)->irq);
+ enable_irq(hwif->irq);
}
}
} else {
if (IDE_CONTROL_REG)
- HWIF(drive)->OUTB(mask ? (drive->ctl | 2) :
+ hwif->OUTB(mask ? (drive->ctl | 2) :
(drive->ctl & ~2),
IDE_CONTROL_REG);
}
@@ -829,12 +811,12 @@ static void hpt3xx_maskproc (ide_drive_t *drive, int mask)
static int hpt366_config_drive_xfer_rate (ide_drive_t *drive)
{
- ide_hwif_t *hwif = HWIF(drive);
+ ide_hwif_t *hwif = drive->hwif;
struct hd_driveid *id = drive->id;
drive->init_speed = 0;
- if (id && (id->capability & 1) && drive->autodma) {
+ if ((id->capability & 1) && drive->autodma) {
if (ide_use_dma(drive)) {
if (config_chipset_for_dma(drive))
@@ -868,15 +850,6 @@ static int hpt366_ide_dma_lostirq (ide_drive_t *drive)
drive->name, __FUNCTION__, reg50h, reg52h, reg5ah);
if (reg5ah & 0x10)
pci_write_config_byte(dev, 0x5a, reg5ah & ~0x10);
-#if 0
- /* how about we flush and reset, mmmkay? */
- pci_write_config_byte(dev, 0x51, 0x1F);
- /* fall through to a reset */
- case dma_start:
- case ide_dma_end:
- /* reset the chips state over and over.. */
- pci_write_config_byte(dev, 0x51, 0x13);
-#endif
return __ide_dma_lostirq(drive);
}
@@ -919,7 +892,7 @@ static void hpt370_lostirq_timeout (ide_drive_t *drive)
u8 dma_stat = 0, dma_cmd = 0;
pci_read_config_byte(HWIF(drive)->pci_dev, reginfo, &bfifo);
- printk("%s: %d bytes in FIFO\n", drive->name, bfifo);
+ printk(KERN_DEBUG "%s: %d bytes in FIFO\n", drive->name, bfifo);
hpt370_clear_engine(drive);
/* get dma command mode */
dma_cmd = hwif->INB(hwif->dma_command);
@@ -1047,15 +1020,6 @@ static void hpt372n_rw_disk(ide_drive_t *drive, struct request *rq)
static void hpt3xx_reset (ide_drive_t *drive)
{
-#if 0
- unsigned long high_16 = pci_resource_start(HWIF(drive)->pci_dev, 4);
- u8 reset = (HWIF(drive)->channel) ? 0x80 : 0x40;
- u8 reg59h = 0;
-
- pci_read_config_byte(HWIF(drive)->pci_dev, 0x59, &reg59h);
- pci_write_config_byte(HWIF(drive)->pci_dev, 0x59, reg59h|reset);
- pci_write_config_byte(HWIF(drive)->pci_dev, 0x59, reg59h);
-#endif
}
static int hpt3xx_tristate (ide_drive_t * drive, int state)
@@ -1065,8 +1029,6 @@ static int hpt3xx_tristate (ide_drive_t * drive, int state)
u8 reg59h = 0, reset = (hwif->channel) ? 0x80 : 0x40;
u8 regXXh = 0, state_reg= (hwif->channel) ? 0x57 : 0x53;
-// hwif->bus_state = state;
-
pci_read_config_byte(dev, 0x59, &reg59h);
pci_read_config_byte(dev, state_reg, &regXXh);
@@ -1093,7 +1055,7 @@ static int hpt3xx_tristate (ide_drive_t * drive, int state)
#define TRISTATE_BIT 0x8000
static int hpt370_busproc(ide_drive_t * drive, int state)
{
- ide_hwif_t *hwif = HWIF(drive);
+ ide_hwif_t *hwif = drive->hwif;
struct pci_dev *dev = hwif->pci_dev;
u8 tristate = 0, resetmask = 0, bus_reg = 0;
u16 tri_reg;
@@ -1148,33 +1110,44 @@ static int hpt370_busproc(ide_drive_t * drive, int state)
return 0;
}
-static int __devinit init_hpt37x(struct pci_dev *dev)
+static void __devinit hpt366_clocking(ide_hwif_t *hwif)
{
+ u32 reg1 = 0;
+ struct hpt_info *info = ide_get_hwifdata(hwif);
+
+ pci_read_config_dword(hwif->pci_dev, 0x40, &reg1);
+
+ /* detect bus speed by looking at control reg timing: */
+ switch((reg1 >> 8) & 7) {
+ case 5:
+ info->speed = forty_base_hpt366;
+ break;
+ case 9:
+ info->speed = twenty_five_base_hpt366;
+ break;
+ case 7:
+ default:
+ info->speed = thirty_three_base_hpt366;
+ break;
+ }
+}
+
+static void __devinit hpt37x_clocking(ide_hwif_t *hwif)
+{
+ struct hpt_info *info = ide_get_hwifdata(hwif);
+ struct pci_dev *dev = hwif->pci_dev;
int adjust, i;
u16 freq;
u32 pll;
u8 reg5bh;
- u8 reg5ah = 0;
- unsigned long dmabase = pci_resource_start(dev, 4);
- u8 did, rid;
- int is_372n = 0;
- pci_read_config_byte(dev, 0x5a, &reg5ah);
- /* interrupt force enable */
- pci_write_config_byte(dev, 0x5a, (reg5ah & ~0x10));
-
- if(dmabase)
- {
- did = inb(dmabase + 0x22);
- rid = inb(dmabase + 0x28);
-
- if((did == 4 && rid == 6) || (did == 5 && rid > 1))
- is_372n = 1;
- }
-
/*
* default to pci clock. make sure MA15/16 are set to output
- * to prevent drives having problems with 40-pin cables.
+ * to prevent drives having problems with 40-pin cables. Needed
+ * for some drives such as IBM-DTLA which will not enter ready
+ * state on reset when PDIAG is a input.
+ *
+ * ToDo: should we set 0x21 when using PLL mode ?
*/
pci_write_config_byte(dev, 0x5b, 0x23);
@@ -1197,9 +1170,7 @@ static int __devinit init_hpt37x(struct pci_dev *dev)
* Currently we always set up the PLL for the 372N
*/
- pci_set_drvdata(dev, NULL);
-
- if(is_372n)
+ if(info->flags & IS_372N)
{
printk(KERN_INFO "hpt: HPT372N detected, using 372N timing.\n");
if(freq < 0x55)
@@ -1227,39 +1198,38 @@ static int __devinit init_hpt37x(struct pci_dev *dev)
pll = F_LOW_PCI_66;
if (pll == F_LOW_PCI_33) {
- if (hpt_minimum_revision(dev,8))
- pci_set_drvdata(dev, (void *) thirty_three_base_hpt374);
- else if (hpt_minimum_revision(dev,5))
- pci_set_drvdata(dev, (void *) thirty_three_base_hpt372);
- else if (hpt_minimum_revision(dev,4))
- pci_set_drvdata(dev, (void *) thirty_three_base_hpt370a);
+ if (info->revision >= 8)
+ info->speed = thirty_three_base_hpt374;
+ else if (info->revision >= 5)
+ info->speed = thirty_three_base_hpt372;
+ else if (info->revision >= 4)
+ info->speed = thirty_three_base_hpt370a;
else
- pci_set_drvdata(dev, (void *) thirty_three_base_hpt370);
- printk("HPT37X: using 33MHz PCI clock\n");
+ info->speed = thirty_three_base_hpt370;
+ printk(KERN_DEBUG "HPT37X: using 33MHz PCI clock\n");
} else if (pll == F_LOW_PCI_40) {
/* Unsupported */
} else if (pll == F_LOW_PCI_50) {
- if (hpt_minimum_revision(dev,8))
- pci_set_drvdata(dev, (void *) fifty_base_hpt370a);
- else if (hpt_minimum_revision(dev,5))
- pci_set_drvdata(dev, (void *) fifty_base_hpt372);
- else if (hpt_minimum_revision(dev,4))
- pci_set_drvdata(dev, (void *) fifty_base_hpt370a);
+ if (info->revision >= 8)
+ info->speed = fifty_base_hpt370a;
+ else if (info->revision >= 5)
+ info->speed = fifty_base_hpt372;
+ else if (info->revision >= 4)
+ info->speed = fifty_base_hpt370a;
else
- pci_set_drvdata(dev, (void *) fifty_base_hpt370a);
- printk("HPT37X: using 50MHz PCI clock\n");
+ info->speed = fifty_base_hpt370a;
+ printk(KERN_DEBUG "HPT37X: using 50MHz PCI clock\n");
} else {
- if (hpt_minimum_revision(dev,8))
- {
+ if (info->revision >= 8) {
printk(KERN_ERR "HPT37x: 66MHz timings are not supported.\n");
}
- else if (hpt_minimum_revision(dev,5))
- pci_set_drvdata(dev, (void *) sixty_six_base_hpt372);
- else if (hpt_minimum_revision(dev,4))
- pci_set_drvdata(dev, (void *) sixty_six_base_hpt370a);
+ else if (info->revision >= 5)
+ info->speed = sixty_six_base_hpt372;
+ else if (info->revision >= 4)
+ info->speed = sixty_six_base_hpt370a;
else
- pci_set_drvdata(dev, (void *) sixty_six_base_hpt370);
- printk("HPT37X: using 66MHz PCI clock\n");
+ info->speed = sixty_six_base_hpt370;
+ printk(KERN_DEBUG "HPT37X: using 66MHz PCI clock\n");
}
}
@@ -1269,11 +1239,19 @@ static int __devinit init_hpt37x(struct pci_dev *dev)
* result in slow reads when using a 33MHz PCI clock. we also
* don't like to use the PLL because it will cause glitches
* on PRST/SRST when the HPT state engine gets reset.
+ *
+ * ToDo: Use 66MHz PLL when ATA133 devices are present on a
+ * 372 device so we can get ATA133 support
*/
- if (pci_get_drvdata(dev))
+ if (info->speed)
goto init_hpt37X_done;
+
+ info->flags |= PLL_MODE;
/*
+ * FIXME: make this work correctly, esp with 372N as per
+ * reference driver code.
+ *
* adjust PLL based upon PCI clock, enable it, and wait for
* stabilization.
*/
@@ -1298,14 +1276,14 @@ static int __devinit init_hpt37x(struct pci_dev *dev)
pci_write_config_dword(dev, 0x5c,
pll & ~0x100);
pci_write_config_byte(dev, 0x5b, 0x21);
- if (hpt_minimum_revision(dev,8))
- pci_set_drvdata(dev, (void *) fifty_base_hpt370a);
- else if (hpt_minimum_revision(dev,5))
- pci_set_drvdata(dev, (void *) fifty_base_hpt372);
- else if (hpt_minimum_revision(dev,4))
- pci_set_drvdata(dev, (void *) fifty_base_hpt370a);
+ if (info->revision >= 8)
+ info->speed = fifty_base_hpt370a;
+ else if (info->revision >= 5)
+ info->speed = fifty_base_hpt372;
+ else if (info->revision >= 4)
+ info->speed = fifty_base_hpt370a;
else
- pci_set_drvdata(dev, (void *) fifty_base_hpt370a);
+ info->speed = fifty_base_hpt370a;
printk("HPT37X: using 50MHz internal PLL\n");
goto init_hpt37X_done;
}
@@ -1318,10 +1296,22 @@ pll_recal:
}
init_hpt37X_done:
+ if (!info->speed)
+ printk(KERN_ERR "HPT37X%s: unknown bus timing [%d %d].\n",
+ (info->flags & IS_372N)?"N":"", pll, freq);
/* reset state engine */
pci_write_config_byte(dev, 0x50, 0x37);
pci_write_config_byte(dev, 0x54, 0x37);
udelay(100);
+}
+
+static int __devinit init_hpt37x(struct pci_dev *dev)
+{
+ u8 reg5ah;
+
+ pci_read_config_byte(dev, 0x5a, &reg5ah);
+ /* interrupt force enable */
+ pci_write_config_byte(dev, 0x5a, (reg5ah & ~0x10));
return 0;
}
@@ -1338,59 +1328,27 @@ static int __devinit init_hpt366(struct pci_dev *dev)
pci_write_config_byte(dev, 0x51, drive_fast & ~0x80);
pci_read_config_dword(dev, 0x40, &reg1);
- /* detect bus speed by looking at control reg timing: */
- switch((reg1 >> 8) & 7) {
- case 5:
- pci_set_drvdata(dev, (void *) forty_base_hpt366);
- break;
- case 9:
- pci_set_drvdata(dev, (void *) twenty_five_base_hpt366);
- break;
- case 7:
- default:
- pci_set_drvdata(dev, (void *) thirty_three_base_hpt366);
- break;
- }
-
- if (!pci_get_drvdata(dev))
- {
- printk(KERN_ERR "hpt366: unknown bus timing.\n");
- pci_set_drvdata(dev, NULL);
- }
return 0;
}
static unsigned int __devinit init_chipset_hpt366(struct pci_dev *dev, const char *name)
{
int ret = 0;
- u8 test = 0;
-
+ /* FIXME: Not portable */
if (dev->resource[PCI_ROM_RESOURCE].start)
pci_write_config_byte(dev, PCI_ROM_ADDRESS,
dev->resource[PCI_ROM_RESOURCE].start | PCI_ROM_ADDRESS_ENABLE);
- pci_read_config_byte(dev, PCI_CACHE_LINE_SIZE, &test);
- if (test != (L1_CACHE_BYTES / 4))
- pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE,
- (L1_CACHE_BYTES / 4));
-
- pci_read_config_byte(dev, PCI_LATENCY_TIMER, &test);
- if (test != 0x78)
- pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
+ pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4));
+ pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
+ pci_write_config_byte(dev, PCI_MIN_GNT, 0x08);
+ pci_write_config_byte(dev, PCI_MAX_LAT, 0x08);
- pci_read_config_byte(dev, PCI_MIN_GNT, &test);
- if (test != 0x08)
- pci_write_config_byte(dev, PCI_MIN_GNT, 0x08);
-
- pci_read_config_byte(dev, PCI_MAX_LAT, &test);
- if (test != 0x08)
- pci_write_config_byte(dev, PCI_MAX_LAT, 0x08);
-
- if (hpt_minimum_revision(dev, 3)) {
+ if (hpt_revision(dev) >= 3)
ret = init_hpt37x(dev);
- } else {
- ret =init_hpt366(dev);
- }
+ else
+ ret = init_hpt366(dev);
+
if (ret)
return ret;
@@ -1400,27 +1358,16 @@ static unsigned int __devinit init_chipset_hpt366(struct pci_dev *dev, const cha
static void __devinit init_hwif_hpt366(ide_hwif_t *hwif)
{
struct pci_dev *dev = hwif->pci_dev;
+ struct hpt_info *info = ide_get_hwifdata(hwif);
u8 ata66 = 0, regmask = (hwif->channel) ? 0x01 : 0x02;
- u8 did, rid;
- unsigned long dmabase = hwif->dma_base;
- int is_372n = 0;
- if(dmabase)
- {
- did = inb(dmabase + 0x22);
- rid = inb(dmabase + 0x28);
-
- if((did == 4 && rid == 6) || (did == 5 && rid > 1))
- is_372n = 1;
- }
-
hwif->tuneproc = &hpt3xx_tune_drive;
hwif->speedproc = &hpt3xx_tune_chipset;
hwif->quirkproc = &hpt3xx_quirkproc;
hwif->intrproc = &hpt3xx_intrproc;
hwif->maskproc = &hpt3xx_maskproc;
- if(is_372n)
+ if(info->flags & IS_372N)
hwif->rw_disk = &hpt372n_rw_disk;
/*
@@ -1428,7 +1375,7 @@ static void __devinit init_hwif_hpt366(ide_hwif_t *hwif)
* address lines to access an external eeprom. To read valid
* cable detect state the pins must be enabled as inputs.
*/
- if (hpt_minimum_revision(dev, 8) && PCI_FUNC(dev->devfn) & 1) {
+ if (info->revision >= 8 && (PCI_FUNC(dev->devfn) & 1)) {
/*
* HPT374 PCI function 1
* - set bit 15 of reg 0x52 to enable TCBLID as input
@@ -1443,7 +1390,7 @@ static void __devinit init_hwif_hpt366(ide_hwif_t *hwif)
pci_read_config_byte(dev, 0x5a, &ata66);
pci_write_config_word(dev, 0x52, mcr3);
pci_write_config_word(dev, 0x56, mcr6);
- } else if (hpt_minimum_revision(dev, 3)) {
+ } else if (info->revision >= 3) {
/*
* HPT370/372 and 374 pcifn 0
* - clear bit 0 of 0x5b to enable P/SCBLID as inputs
@@ -1470,7 +1417,7 @@ static void __devinit init_hwif_hpt366(ide_hwif_t *hwif)
hwif->serialized = hwif->mate->serialized = 1;
#endif
- if (hpt_minimum_revision(dev,3)) {
+ if (info->revision >= 3) {
u8 reg5ah = 0;
pci_write_config_byte(dev, 0x5a, reg5ah & ~0x10);
/*
@@ -1480,8 +1427,7 @@ static void __devinit init_hwif_hpt366(ide_hwif_t *hwif)
*/
hwif->resetproc = &hpt3xx_reset;
hwif->busproc = &hpt370_busproc;
-// hwif->drives[0].autotune = hwif->drives[1].autotune = 1;
- } else if (hpt_minimum_revision(dev,2)) {
+ } else if (info->revision >= 2) {
hwif->resetproc = &hpt3xx_reset;
hwif->busproc = &hpt3xx_tristate;
} else {
@@ -1502,18 +1448,18 @@ static void __devinit init_hwif_hpt366(ide_hwif_t *hwif)
hwif->udma_four = ((ata66 & regmask) ? 0 : 1);
hwif->ide_dma_check = &hpt366_config_drive_xfer_rate;
- if (hpt_minimum_revision(dev,8)) {
+ if (info->revision >= 8) {
hwif->ide_dma_test_irq = &hpt374_ide_dma_test_irq;
hwif->ide_dma_end = &hpt374_ide_dma_end;
- } else if (hpt_minimum_revision(dev,5)) {
+ } else if (info->revision >= 5) {
hwif->ide_dma_test_irq = &hpt374_ide_dma_test_irq;
hwif->ide_dma_end = &hpt374_ide_dma_end;
- } else if (hpt_minimum_revision(dev,3)) {
+ } else if (info->revision >= 3) {
hwif->dma_start = &hpt370_ide_dma_start;
hwif->ide_dma_end = &hpt370_ide_dma_end;
hwif->ide_dma_timeout = &hpt370_ide_dma_timeout;
hwif->ide_dma_lostirq = &hpt370_ide_dma_lostirq;
- } else if (hpt_minimum_revision(dev,2))
+ } else if (info->revision >= 2)
hwif->ide_dma_lostirq = &hpt366_ide_dma_lostirq;
else
hwif->ide_dma_lostirq = &hpt366_ide_dma_lostirq;
@@ -1526,6 +1472,7 @@ static void __devinit init_hwif_hpt366(ide_hwif_t *hwif)
static void __devinit init_dma_hpt366(ide_hwif_t *hwif, unsigned long dmabase)
{
+ struct hpt_info *info = ide_get_hwifdata(hwif);
u8 masterdma = 0, slavedma = 0;
u8 dma_new = 0, dma_old = 0;
u8 primary = hwif->channel ? 0x4b : 0x43;
@@ -1535,8 +1482,7 @@ static void __devinit init_dma_hpt366(ide_hwif_t *hwif, unsigned long dmabase)
if (!dmabase)
return;
- if(pci_get_drvdata(hwif->pci_dev) == NULL)
- {
+ if(info->speed == NULL) {
printk(KERN_WARNING "hpt: no known IDE timings, disabling DMA.\n");
return;
}
@@ -1559,6 +1505,40 @@ static void __devinit init_dma_hpt366(ide_hwif_t *hwif, unsigned long dmabase)
ide_setup_dma(hwif, dmabase, 8);
}
+/*
+ * We "borrow" this hook in order to set the data structures
+ * up early enough before dma or init_hwif calls are made.
+ */
+
+static void __devinit init_iops_hpt366(ide_hwif_t *hwif)
+{
+ struct hpt_info *info = kmalloc(sizeof(struct hpt_info), GFP_KERNEL);
+ unsigned long dmabase = pci_resource_start(hwif->pci_dev, 4);
+ u8 did, rid;
+
+ if(info == NULL) {
+ printk(KERN_WARNING "hpt366: out of memory.\n");
+ return;
+ }
+ memset(info, 0, sizeof(struct hpt_info));
+ ide_set_hwifdata(hwif, info);
+
+ if(dmabase) {
+ did = inb(dmabase + 0x22);
+ rid = inb(dmabase + 0x28);
+
+ if((did == 4 && rid == 6) || (did == 5 && rid > 1))
+ info->flags |= IS_372N;
+ }
+
+ info->revision = hpt_revision(hwif->pci_dev);
+
+ if (info->revision >= 3)
+ hpt37x_clocking(hwif);
+ else
+ hpt366_clocking(hwif);
+}
+
static int __devinit init_setup_hpt374(struct pci_dev *dev, ide_pci_device_t *d)
{
struct pci_dev *findev = NULL;
@@ -1646,6 +1626,7 @@ static ide_pci_device_t hpt366_chipsets[] __devinitdata = {
.name = "HPT366",
.init_setup = init_setup_hpt366,
.init_chipset = init_chipset_hpt366,
+ .init_iops = init_iops_hpt366,
.init_hwif = init_hwif_hpt366,
.init_dma = init_dma_hpt366,
.channels = 2,
@@ -1656,6 +1637,7 @@ static ide_pci_device_t hpt366_chipsets[] __devinitdata = {
.name = "HPT372A",
.init_setup = init_setup_hpt37x,
.init_chipset = init_chipset_hpt366,
+ .init_iops = init_iops_hpt366,
.init_hwif = init_hwif_hpt366,
.init_dma = init_dma_hpt366,
.channels = 2,
@@ -1665,6 +1647,7 @@ static ide_pci_device_t hpt366_chipsets[] __devinitdata = {
.name = "HPT302",
.init_setup = init_setup_hpt37x,
.init_chipset = init_chipset_hpt366,
+ .init_iops = init_iops_hpt366,
.init_hwif = init_hwif_hpt366,
.init_dma = init_dma_hpt366,
.channels = 2,
@@ -1674,6 +1657,7 @@ static ide_pci_device_t hpt366_chipsets[] __devinitdata = {
.name = "HPT371",
.init_setup = init_setup_hpt37x,
.init_chipset = init_chipset_hpt366,
+ .init_iops = init_iops_hpt366,
.init_hwif = init_hwif_hpt366,
.init_dma = init_dma_hpt366,
.channels = 2,
@@ -1683,6 +1667,7 @@ static ide_pci_device_t hpt366_chipsets[] __devinitdata = {
.name = "HPT374",
.init_setup = init_setup_hpt374,
.init_chipset = init_chipset_hpt366,
+ .init_iops = init_iops_hpt366,
.init_hwif = init_hwif_hpt366,
.init_dma = init_dma_hpt366,
.channels = 2, /* 4 */
@@ -1692,6 +1677,7 @@ static ide_pci_device_t hpt366_chipsets[] __devinitdata = {
.name = "HPT372N",
.init_setup = init_setup_hpt37x,
.init_chipset = init_chipset_hpt366,
+ .init_iops = init_iops_hpt366,
.init_hwif = init_hwif_hpt366,
.init_dma = init_dma_hpt366,
.channels = 2, /* 4 */
diff --git a/drivers/ide/pci/it821x.c b/drivers/ide/pci/it821x.c
new file mode 100644
index 00000000000..e440036e651
--- /dev/null
+++ b/drivers/ide/pci/it821x.c
@@ -0,0 +1,812 @@
+
+/*
+ * linux/drivers/ide/pci/it821x.c Version 0.09 December 2004
+ *
+ * Copyright (C) 2004 Red Hat <alan@redhat.com>
+ *
+ * May be copied or modified under the terms of the GNU General Public License
+ * Based in part on the ITE vendor provided SCSI driver.
+ *
+ * Documentation available from
+ * http://www.ite.com.tw/pc/IT8212F_V04.pdf
+ * Some other documents are NDA.
+ *
+ * The ITE8212 isn't exactly a standard IDE controller. It has two
+ * modes. In pass through mode then it is an IDE controller. In its smart
+ * mode its actually quite a capable hardware raid controller disguised
+ * as an IDE controller. Smart mode only understands DMA read/write and
+ * identify, none of the fancier commands apply. The IT8211 is identical
+ * in other respects but lacks the raid mode.
+ *
+ * Errata:
+ * o Rev 0x10 also requires master/slave hold the same DMA timings and
+ * cannot do ATAPI MWDMA.
+ * o The identify data for raid volumes lacks CHS info (technically ok)
+ * but also fails to set the LBA28 and other bits. We fix these in
+ * the IDE probe quirk code.
+ * o If you write LBA48 sized I/O's (ie > 256 sector) in smart mode
+ * raid then the controller firmware dies
+ * o Smart mode without RAID doesn't clear all the necessary identify
+ * bits to reduce the command set to the one used
+ *
+ * This has a few impacts on the driver
+ * - In pass through mode we do all the work you would expect
+ * - In smart mode the clocking set up is done by the controller generally
+ * but we must watch the other limits and filter.
+ * - There are a few extra vendor commands that actually talk to the
+ * controller but only work PIO with no IRQ.
+ *
+ * Vendor areas of the identify block in smart mode are used for the
+ * timing and policy set up. Each HDD in raid mode also has a serial
+ * block on the disk. The hardware extra commands are get/set chip status,
+ * rebuild, get rebuild status.
+ *
+ * In Linux the driver supports pass through mode as if the device was
+ * just another IDE controller. If the smart mode is running then
+ * volumes are managed by the controller firmware and each IDE "disk"
+ * is a raid volume. Even more cute - the controller can do automated
+ * hotplug and rebuild.
+ *
+ * The pass through controller itself is a little demented. It has a
+ * flaw that it has a single set of PIO/MWDMA timings per channel so
+ * non UDMA devices restrict each others performance. It also has a
+ * single clock source per channel so mixed UDMA100/133 performance
+ * isn't perfect and we have to pick a clock. Thankfully none of this
+ * matters in smart mode. ATAPI DMA is not currently supported.
+ *
+ * It seems the smart mode is a win for RAID1/RAID10 but otherwise not.
+ *
+ * TODO
+ * - ATAPI UDMA is ok but not MWDMA it seems
+ * - RAID configuration ioctls
+ * - Move to libata once it grows up
+ */
+
+#include <linux/config.h>
+#include <linux/types.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/delay.h>
+#include <linux/hdreg.h>
+#include <linux/ide.h>
+#include <linux/init.h>
+
+#include <asm/io.h>
+
+struct it821x_dev
+{
+ unsigned int smart:1, /* Are we in smart raid mode */
+ timing10:1; /* Rev 0x10 */
+ u8 clock_mode; /* 0, ATA_50 or ATA_66 */
+ u8 want[2][2]; /* Mode/Pri log for master slave */
+ /* We need these for switching the clock when DMA goes on/off
+ The high byte is the 66Mhz timing */
+ u16 pio[2]; /* Cached PIO values */
+ u16 mwdma[2]; /* Cached MWDMA values */
+ u16 udma[2]; /* Cached UDMA values (per drive) */
+};
+
+#define ATA_66 0
+#define ATA_50 1
+#define ATA_ANY 2
+
+#define UDMA_OFF 0
+#define MWDMA_OFF 0
+
+/*
+ * We allow users to force the card into non raid mode without
+ * flashing the alternative BIOS. This is also neccessary right now
+ * for embedded platforms that cannot run a PC BIOS but are using this
+ * device.
+ */
+
+static int it8212_noraid;
+
+/**
+ * it821x_program - program the PIO/MWDMA registers
+ * @drive: drive to tune
+ *
+ * Program the PIO/MWDMA timing for this channel according to the
+ * current clock.
+ */
+
+static void it821x_program(ide_drive_t *drive, u16 timing)
+{
+ ide_hwif_t *hwif = drive->hwif;
+ struct it821x_dev *itdev = ide_get_hwifdata(hwif);
+ int channel = hwif->channel;
+ u8 conf;
+
+ /* Program PIO/MWDMA timing bits */
+ if(itdev->clock_mode == ATA_66)
+ conf = timing >> 8;
+ else
+ conf = timing & 0xFF;
+ pci_write_config_byte(hwif->pci_dev, 0x54 + 4 * channel, conf);
+}
+
+/**
+ * it821x_program_udma - program the UDMA registers
+ * @drive: drive to tune
+ *
+ * Program the UDMA timing for this drive according to the
+ * current clock.
+ */
+
+static void it821x_program_udma(ide_drive_t *drive, u16 timing)
+{
+ ide_hwif_t *hwif = drive->hwif;
+ struct it821x_dev *itdev = ide_get_hwifdata(hwif);
+ int channel = hwif->channel;
+ int unit = drive->select.b.unit;
+ u8 conf;
+
+ /* Program UDMA timing bits */
+ if(itdev->clock_mode == ATA_66)
+ conf = timing >> 8;
+ else
+ conf = timing & 0xFF;
+ if(itdev->timing10 == 0)
+ pci_write_config_byte(hwif->pci_dev, 0x56 + 4 * channel + unit, conf);
+ else {
+ pci_write_config_byte(hwif->pci_dev, 0x56 + 4 * channel, conf);
+ pci_write_config_byte(hwif->pci_dev, 0x56 + 4 * channel + 1, conf);
+ }
+}
+
+
+/**
+ * it821x_clock_strategy
+ * @hwif: hardware interface
+ *
+ * Select between the 50 and 66Mhz base clocks to get the best
+ * results for this interface.
+ */
+
+static void it821x_clock_strategy(ide_drive_t *drive)
+{
+ ide_hwif_t *hwif = drive->hwif;
+ struct it821x_dev *itdev = ide_get_hwifdata(hwif);
+
+ u8 unit = drive->select.b.unit;
+ ide_drive_t *pair = &hwif->drives[1-unit];
+
+ int clock, altclock;
+ u8 v;
+ int sel = 0;
+
+ if(itdev->want[0][0] > itdev->want[1][0]) {
+ clock = itdev->want[0][1];
+ altclock = itdev->want[1][1];
+ } else {
+ clock = itdev->want[1][1];
+ altclock = itdev->want[0][1];
+ }
+
+ /* Master doesn't care does the slave ? */
+ if(clock == ATA_ANY)
+ clock = altclock;
+
+ /* Nobody cares - keep the same clock */
+ if(clock == ATA_ANY)
+ return;
+ /* No change */
+ if(clock == itdev->clock_mode)
+ return;
+
+ /* Load this into the controller ? */
+ if(clock == ATA_66)
+ itdev->clock_mode = ATA_66;
+ else {
+ itdev->clock_mode = ATA_50;
+ sel = 1;
+ }
+ pci_read_config_byte(hwif->pci_dev, 0x50, &v);
+ v &= ~(1 << (1 + hwif->channel));
+ v |= sel << (1 + hwif->channel);
+ pci_write_config_byte(hwif->pci_dev, 0x50, v);
+
+ /*
+ * Reprogram the UDMA/PIO of the pair drive for the switch
+ * MWDMA will be dealt with by the dma switcher
+ */
+ if(pair && itdev->udma[1-unit] != UDMA_OFF) {
+ it821x_program_udma(pair, itdev->udma[1-unit]);
+ it821x_program(pair, itdev->pio[1-unit]);
+ }
+ /*
+ * Reprogram the UDMA/PIO of our drive for the switch.
+ * MWDMA will be dealt with by the dma switcher
+ */
+ if(itdev->udma[unit] != UDMA_OFF) {
+ it821x_program_udma(drive, itdev->udma[unit]);
+ it821x_program(drive, itdev->pio[unit]);
+ }
+}
+
+/**
+ * it821x_ratemask - Compute available modes
+ * @drive: IDE drive
+ *
+ * Compute the available speeds for the devices on the interface. This
+ * is all modes to ATA133 clipped by drive cable setup.
+ */
+
+static u8 it821x_ratemask (ide_drive_t *drive)
+{
+ u8 mode = 4;
+ if (!eighty_ninty_three(drive))
+ mode = min(mode, (u8)1);
+ return mode;
+}
+
+/**
+ * it821x_tuneproc - tune a drive
+ * @drive: drive to tune
+ * @mode_wanted: the target operating mode
+ *
+ * Load the timing settings for this device mode into the
+ * controller. By the time we are called the mode has been
+ * modified as neccessary to handle the absence of seperate
+ * master/slave timers for MWDMA/PIO.
+ *
+ * This code is only used in pass through mode.
+ */
+
+static void it821x_tuneproc (ide_drive_t *drive, byte mode_wanted)
+{
+ ide_hwif_t *hwif = drive->hwif;
+ struct it821x_dev *itdev = ide_get_hwifdata(hwif);
+ int unit = drive->select.b.unit;
+
+ /* Spec says 89 ref driver uses 88 */
+ static u16 pio[] = { 0xAA88, 0xA382, 0xA181, 0x3332, 0x3121 };
+ static u8 pio_want[] = { ATA_66, ATA_66, ATA_66, ATA_66, ATA_ANY };
+
+ if(itdev->smart)
+ return;
+
+ /* We prefer 66Mhz clock for PIO 0-3, don't care for PIO4 */
+ itdev->want[unit][1] = pio_want[mode_wanted];
+ itdev->want[unit][0] = 1; /* PIO is lowest priority */
+ itdev->pio[unit] = pio[mode_wanted];
+ it821x_clock_strategy(drive);
+ it821x_program(drive, itdev->pio[unit]);
+}
+
+/**
+ * it821x_tune_mwdma - tune a channel for MWDMA
+ * @drive: drive to set up
+ * @mode_wanted: the target operating mode
+ *
+ * Load the timing settings for this device mode into the
+ * controller when doing MWDMA in pass through mode. The caller
+ * must manage the whole lack of per device MWDMA/PIO timings and
+ * the shared MWDMA/PIO timing register.
+ */
+
+static void it821x_tune_mwdma (ide_drive_t *drive, byte mode_wanted)
+{
+ ide_hwif_t *hwif = drive->hwif;
+ struct it821x_dev *itdev = (void *)ide_get_hwifdata(hwif);
+ int unit = drive->select.b.unit;
+ int channel = hwif->channel;
+ u8 conf;
+
+ static u16 dma[] = { 0x8866, 0x3222, 0x3121 };
+ static u8 mwdma_want[] = { ATA_ANY, ATA_66, ATA_ANY };
+
+ itdev->want[unit][1] = mwdma_want[mode_wanted];
+ itdev->want[unit][0] = 2; /* MWDMA is low priority */
+ itdev->mwdma[unit] = dma[mode_wanted];
+ itdev->udma[unit] = UDMA_OFF;
+
+ /* UDMA bits off - Revision 0x10 do them in pairs */
+ pci_read_config_byte(hwif->pci_dev, 0x50, &conf);
+ if(itdev->timing10)
+ conf |= channel ? 0x60: 0x18;
+ else
+ conf |= 1 << (3 + 2 * channel + unit);
+ pci_write_config_byte(hwif->pci_dev, 0x50, conf);
+
+ it821x_clock_strategy(drive);
+ /* FIXME: do we need to program this ? */
+ /* it821x_program(drive, itdev->mwdma[unit]); */
+}
+
+/**
+ * it821x_tune_udma - tune a channel for UDMA
+ * @drive: drive to set up
+ * @mode_wanted: the target operating mode
+ *
+ * Load the timing settings for this device mode into the
+ * controller when doing UDMA modes in pass through.
+ */
+
+static void it821x_tune_udma (ide_drive_t *drive, byte mode_wanted)
+{
+ ide_hwif_t *hwif = drive->hwif;
+ struct it821x_dev *itdev = ide_get_hwifdata(hwif);
+ int unit = drive->select.b.unit;
+ int channel = hwif->channel;
+ u8 conf;
+
+ static u16 udma[] = { 0x4433, 0x4231, 0x3121, 0x2121, 0x1111, 0x2211, 0x1111 };
+ static u8 udma_want[] = { ATA_ANY, ATA_50, ATA_ANY, ATA_66, ATA_66, ATA_50, ATA_66 };
+
+ itdev->want[unit][1] = udma_want[mode_wanted];
+ itdev->want[unit][0] = 3; /* UDMA is high priority */
+ itdev->mwdma[unit] = MWDMA_OFF;
+ itdev->udma[unit] = udma[mode_wanted];
+ if(mode_wanted >= 5)
+ itdev->udma[unit] |= 0x8080; /* UDMA 5/6 select on */
+
+ /* UDMA on. Again revision 0x10 must do the pair */
+ pci_read_config_byte(hwif->pci_dev, 0x50, &conf);
+ if(itdev->timing10)
+ conf &= channel ? 0x9F: 0xE7;
+ else
+ conf &= ~ (1 << (3 + 2 * channel + unit));
+ pci_write_config_byte(hwif->pci_dev, 0x50, conf);
+
+ it821x_clock_strategy(drive);
+ it821x_program_udma(drive, itdev->udma[unit]);
+
+}
+
+/**
+ * config_it821x_chipset_for_pio - set drive timings
+ * @drive: drive to tune
+ * @speed we want
+ *
+ * Compute the best pio mode we can for a given device. We must
+ * pick a speed that does not cause problems with the other device
+ * on the cable.
+ */
+
+static void config_it821x_chipset_for_pio (ide_drive_t *drive, byte set_speed)
+{
+ u8 unit = drive->select.b.unit;
+ ide_hwif_t *hwif = drive->hwif;
+ ide_drive_t *pair = &hwif->drives[1-unit];
+ u8 speed = 0, set_pio = ide_get_best_pio_mode(drive, 255, 5, NULL);
+ u8 pair_pio;
+
+ /* We have to deal with this mess in pairs */
+ if(pair != NULL) {
+ pair_pio = ide_get_best_pio_mode(pair, 255, 5, NULL);
+ /* Trim PIO to the slowest of the master/slave */
+ if(pair_pio < set_pio)
+ set_pio = pair_pio;
+ }
+ it821x_tuneproc(drive, set_pio);
+ speed = XFER_PIO_0 + set_pio;
+ /* XXX - We trim to the lowest of the pair so the other drive
+ will always be fine at this point until we do hotplug passthru */
+
+ if (set_speed)
+ (void) ide_config_drive_speed(drive, speed);
+}
+
+/**
+ * it821x_dma_read - DMA hook
+ * @drive: drive for DMA
+ *
+ * The IT821x has a single timing register for MWDMA and for PIO
+ * operations. As we flip back and forth we have to reload the
+ * clock. In addition the rev 0x10 device only works if the same
+ * timing value is loaded into the master and slave UDMA clock
+ * so we must also reload that.
+ *
+ * FIXME: we could figure out in advance if we need to do reloads
+ */
+
+static void it821x_dma_start(ide_drive_t *drive)
+{
+ ide_hwif_t *hwif = drive->hwif;
+ struct it821x_dev *itdev = ide_get_hwifdata(hwif);
+ int unit = drive->select.b.unit;
+ if(itdev->mwdma[unit] != MWDMA_OFF)
+ it821x_program(drive, itdev->mwdma[unit]);
+ else if(itdev->udma[unit] != UDMA_OFF && itdev->timing10)
+ it821x_program_udma(drive, itdev->udma[unit]);
+ ide_dma_start(drive);
+}
+
+/**
+ * it821x_dma_write - DMA hook
+ * @drive: drive for DMA stop
+ *
+ * The IT821x has a single timing register for MWDMA and for PIO
+ * operations. As we flip back and forth we have to reload the
+ * clock.
+ */
+
+static int it821x_dma_end(ide_drive_t *drive)
+{
+ ide_hwif_t *hwif = drive->hwif;
+ int unit = drive->select.b.unit;
+ struct it821x_dev *itdev = ide_get_hwifdata(hwif);
+ int ret = __ide_dma_end(drive);
+ if(itdev->mwdma[unit] != MWDMA_OFF)
+ it821x_program(drive, itdev->pio[unit]);
+ return ret;
+}
+
+
+/**
+ * it821x_tune_chipset - set controller timings
+ * @drive: Drive to set up
+ * @xferspeed: speed we want to achieve
+ *
+ * Tune the ITE chipset for the desired mode. If we can't achieve
+ * the desired mode then tune for a lower one, but ultimately
+ * make the thing work.
+ */
+
+static int it821x_tune_chipset (ide_drive_t *drive, byte xferspeed)
+{
+
+ ide_hwif_t *hwif = drive->hwif;
+ struct it821x_dev *itdev = ide_get_hwifdata(hwif);
+ u8 speed = ide_rate_filter(it821x_ratemask(drive), xferspeed);
+
+ if(!itdev->smart) {
+ switch(speed) {
+ case XFER_PIO_4:
+ case XFER_PIO_3:
+ case XFER_PIO_2:
+ case XFER_PIO_1:
+ case XFER_PIO_0:
+ it821x_tuneproc(drive, (speed - XFER_PIO_0));
+ break;
+ /* MWDMA tuning is really hard because our MWDMA and PIO
+ timings are kept in the same place. We can switch in the
+ host dma on/off callbacks */
+ case XFER_MW_DMA_2:
+ case XFER_MW_DMA_1:
+ case XFER_MW_DMA_0:
+ it821x_tune_mwdma(drive, (speed - XFER_MW_DMA_0));
+ break;
+ case XFER_UDMA_6:
+ case XFER_UDMA_5:
+ case XFER_UDMA_4:
+ case XFER_UDMA_3:
+ case XFER_UDMA_2:
+ case XFER_UDMA_1:
+ case XFER_UDMA_0:
+ it821x_tune_udma(drive, (speed - XFER_UDMA_0));
+ break;
+ default:
+ return 1;
+ }
+ }
+ /*
+ * In smart mode the clocking is done by the host controller
+ * snooping the mode we picked. The rest of it is not our problem
+ */
+ return ide_config_drive_speed(drive, speed);
+}
+
+/**
+ * config_chipset_for_dma - configure for DMA
+ * @drive: drive to configure
+ *
+ * Called by the IDE layer when it wants the timings set up.
+ */
+
+static int config_chipset_for_dma (ide_drive_t *drive)
+{
+ u8 speed = ide_dma_speed(drive, it821x_ratemask(drive));
+
+ config_it821x_chipset_for_pio(drive, !speed);
+ it821x_tune_chipset(drive, speed);
+ return ide_dma_enable(drive);
+}
+
+/**
+ * it821x_configure_drive_for_dma - set up for DMA transfers
+ * @drive: drive we are going to set up
+ *
+ * Set up the drive for DMA, tune the controller and drive as
+ * required. If the drive isn't suitable for DMA or we hit
+ * other problems then we will drop down to PIO and set up
+ * PIO appropriately
+ */
+
+static int it821x_config_drive_for_dma (ide_drive_t *drive)
+{
+ ide_hwif_t *hwif = drive->hwif;
+
+ if (ide_use_dma(drive)) {
+ if (config_chipset_for_dma(drive))
+ return hwif->ide_dma_on(drive);
+ }
+ config_it821x_chipset_for_pio(drive, 1);
+ return hwif->ide_dma_off_quietly(drive);
+}
+
+/**
+ * ata66_it821x - check for 80 pin cable
+ * @hwif: interface to check
+ *
+ * Check for the presence of an ATA66 capable cable on the
+ * interface. Problematic as it seems some cards don't have
+ * the needed logic onboard.
+ */
+
+static unsigned int __devinit ata66_it821x(ide_hwif_t *hwif)
+{
+ /* The reference driver also only does disk side */
+ return 1;
+}
+
+/**
+ * it821x_fixup - post init callback
+ * @hwif: interface
+ *
+ * This callback is run after the drives have been probed but
+ * before anything gets attached. It allows drivers to do any
+ * final tuning that is needed, or fixups to work around bugs.
+ */
+
+static void __devinit it821x_fixups(ide_hwif_t *hwif)
+{
+ struct it821x_dev *itdev = ide_get_hwifdata(hwif);
+ int i;
+
+ if(!itdev->smart) {
+ /*
+ * If we are in pass through mode then not much
+ * needs to be done, but we do bother to clear the
+ * IRQ mask as we may well be in PIO (eg rev 0x10)
+ * for now and we know unmasking is safe on this chipset.
+ */
+ for (i = 0; i < 2; i++) {
+ ide_drive_t *drive = &hwif->drives[i];
+ if(drive->present)
+ drive->unmask = 1;
+ }
+ return;
+ }
+ /*
+ * Perform fixups on smart mode. We need to "lose" some
+ * capabilities the firmware lacks but does not filter, and
+ * also patch up some capability bits that it forgets to set
+ * in RAID mode.
+ */
+
+ for(i = 0; i < 2; i++) {
+ ide_drive_t *drive = &hwif->drives[i];
+ struct hd_driveid *id;
+ u16 *idbits;
+
+ if(!drive->present)
+ continue;
+ id = drive->id;
+ idbits = (u16 *)drive->id;
+
+ /* Check for RAID v native */
+ if(strstr(id->model, "Integrated Technology Express")) {
+ /* In raid mode the ident block is slightly buggy
+ We need to set the bits so that the IDE layer knows
+ LBA28. LBA48 and DMA ar valid */
+ id->capability |= 3; /* LBA28, DMA */
+ id->command_set_2 |= 0x0400; /* LBA48 valid */
+ id->cfs_enable_2 |= 0x0400; /* LBA48 on */
+ /* Reporting logic */
+ printk(KERN_INFO "%s: IT8212 %sRAID %d volume",
+ drive->name,
+ idbits[147] ? "Bootable ":"",
+ idbits[129]);
+ if(idbits[129] != 1)
+ printk("(%dK stripe)", idbits[146]);
+ printk(".\n");
+ /* Now the core code will have wrongly decided no DMA
+ so we need to fix this */
+ hwif->ide_dma_off_quietly(drive);
+#ifdef CONFIG_IDEDMA_ONLYDISK
+ if (drive->media == ide_disk)
+#endif
+ hwif->ide_dma_check(drive);
+ } else {
+ /* Non RAID volume. Fixups to stop the core code
+ doing unsupported things */
+ id->field_valid &= 1;
+ id->queue_depth = 0;
+ id->command_set_1 = 0;
+ id->command_set_2 &= 0xC400;
+ id->cfsse &= 0xC000;
+ id->cfs_enable_1 = 0;
+ id->cfs_enable_2 &= 0xC400;
+ id->csf_default &= 0xC000;
+ id->word127 = 0;
+ id->dlf = 0;
+ id->csfo = 0;
+ id->cfa_power = 0;
+ printk(KERN_INFO "%s: Performing identify fixups.\n",
+ drive->name);
+ }
+ }
+
+}
+
+/**
+ * init_hwif_it821x - set up hwif structs
+ * @hwif: interface to set up
+ *
+ * We do the basic set up of the interface structure. The IT8212
+ * requires several custom handlers so we override the default
+ * ide DMA handlers appropriately
+ */
+
+static void __devinit init_hwif_it821x(ide_hwif_t *hwif)
+{
+ struct it821x_dev *idev = kmalloc(sizeof(struct it821x_dev), GFP_KERNEL);
+ u8 conf;
+
+ if(idev == NULL) {
+ printk(KERN_ERR "it821x: out of memory, falling back to legacy behaviour.\n");
+ goto fallback;
+ }
+ memset(idev, 0, sizeof(struct it821x_dev));
+ ide_set_hwifdata(hwif, idev);
+
+ pci_read_config_byte(hwif->pci_dev, 0x50, &conf);
+ if(conf & 1) {
+ idev->smart = 1;
+ hwif->atapi_dma = 0;
+ /* Long I/O's although allowed in LBA48 space cause the
+ onboard firmware to enter the twighlight zone */
+ hwif->rqsize = 256;
+ }
+
+ /* Pull the current clocks from 0x50 also */
+ if (conf & (1 << (1 + hwif->channel)))
+ idev->clock_mode = ATA_50;
+ else
+ idev->clock_mode = ATA_66;
+
+ idev->want[0][1] = ATA_ANY;
+ idev->want[1][1] = ATA_ANY;
+
+ /*
+ * Not in the docs but according to the reference driver
+ * this is neccessary.
+ */
+
+ pci_read_config_byte(hwif->pci_dev, 0x08, &conf);
+ if(conf == 0x10) {
+ idev->timing10 = 1;
+ hwif->atapi_dma = 0;
+ if(!idev->smart)
+ printk(KERN_WARNING "it821x: Revision 0x10, workarounds activated.\n");
+ }
+
+ hwif->speedproc = &it821x_tune_chipset;
+ hwif->tuneproc = &it821x_tuneproc;
+
+ /* MWDMA/PIO clock switching for pass through mode */
+ if(!idev->smart) {
+ hwif->dma_start = &it821x_dma_start;
+ hwif->ide_dma_end = &it821x_dma_end;
+ }
+
+ hwif->drives[0].autotune = 1;
+ hwif->drives[1].autotune = 1;
+
+ if (!hwif->dma_base)
+ goto fallback;
+
+ hwif->ultra_mask = 0x7f;
+ hwif->mwdma_mask = 0x07;
+ hwif->swdma_mask = 0x07;
+
+ hwif->ide_dma_check = &it821x_config_drive_for_dma;
+ if (!(hwif->udma_four))
+ hwif->udma_four = ata66_it821x(hwif);
+
+ /*
+ * The BIOS often doesn't set up DMA on this controller
+ * so we always do it.
+ */
+
+ hwif->autodma = 1;
+ hwif->drives[0].autodma = hwif->autodma;
+ hwif->drives[1].autodma = hwif->autodma;
+ return;
+fallback:
+ hwif->autodma = 0;
+ return;
+}
+
+static void __devinit it8212_disable_raid(struct pci_dev *dev)
+{
+ /* Reset local CPU, and set BIOS not ready */
+ pci_write_config_byte(dev, 0x5E, 0x01);
+
+ /* Set to bypass mode, and reset PCI bus */
+ pci_write_config_byte(dev, 0x50, 0x00);
+ pci_write_config_word(dev, PCI_COMMAND,
+ PCI_COMMAND_PARITY | PCI_COMMAND_IO |
+ PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
+ pci_write_config_word(dev, 0x40, 0xA0F3);
+
+ pci_write_config_dword(dev,0x4C, 0x02040204);
+ pci_write_config_byte(dev, 0x42, 0x36);
+ pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0);
+}
+
+static unsigned int __devinit init_chipset_it821x(struct pci_dev *dev, const char *name)
+{
+ u8 conf;
+ static char *mode[2] = { "pass through", "smart" };
+
+ /* Force the card into bypass mode if so requested */
+ if (it8212_noraid) {
+ printk(KERN_INFO "it8212: forcing bypass mode.\n");
+ it8212_disable_raid(dev);
+ }
+ pci_read_config_byte(dev, 0x50, &conf);
+ printk(KERN_INFO "it821x: controller in %s mode.\n", mode[conf & 1]);
+ return 0;
+}
+
+
+#define DECLARE_ITE_DEV(name_str) \
+ { \
+ .name = name_str, \
+ .init_chipset = init_chipset_it821x, \
+ .init_hwif = init_hwif_it821x, \
+ .channels = 2, \
+ .autodma = AUTODMA, \
+ .bootable = ON_BOARD, \
+ .fixup = it821x_fixups \
+ }
+
+static ide_pci_device_t it821x_chipsets[] __devinitdata = {
+ /* 0 */ DECLARE_ITE_DEV("IT8212"),
+};
+
+/**
+ * it821x_init_one - pci layer discovery entry
+ * @dev: PCI device
+ * @id: ident table entry
+ *
+ * Called by the PCI code when it finds an ITE821x controller.
+ * We then use the IDE PCI generic helper to do most of the work.
+ */
+
+static int __devinit it821x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+ ide_setup_pci_device(dev, &it821x_chipsets[id->driver_data]);
+ return 0;
+}
+
+static struct pci_device_id it821x_pci_tbl[] = {
+ { PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8211, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
+ { PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8212, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
+ { 0, },
+};
+
+MODULE_DEVICE_TABLE(pci, it821x_pci_tbl);
+
+static struct pci_driver driver = {
+ .name = "ITE821x IDE",
+ .id_table = it821x_pci_tbl,
+ .probe = it821x_init_one,
+};
+
+static int __init it821x_ide_init(void)
+{
+ return ide_pci_register_driver(&driver);
+}
+
+module_init(it821x_ide_init);
+
+module_param_named(noraid, it8212_noraid, int, S_IRUGO);
+MODULE_PARM_DESC(it8212_noraid, "Force card into bypass mode");
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("PCI driver module for the ITE 821x");
+MODULE_LICENSE("GPL");
diff --git a/drivers/ide/pci/serverworks.c b/drivers/ide/pci/serverworks.c
index 82a1103b241..c6f5fa4b4ca 100644
--- a/drivers/ide/pci/serverworks.c
+++ b/drivers/ide/pci/serverworks.c
@@ -442,7 +442,7 @@ static unsigned int __devinit init_chipset_svwks (struct pci_dev *dev, const cha
return (dev->irq) ? dev->irq : 0;
}
-static unsigned int __init ata66_svwks_svwks (ide_hwif_t *hwif)
+static unsigned int __devinit ata66_svwks_svwks (ide_hwif_t *hwif)
{
return 1;
}
@@ -454,7 +454,7 @@ static unsigned int __init ata66_svwks_svwks (ide_hwif_t *hwif)
* Bit 14 clear = primary IDE channel does not have 80-pin cable.
* Bit 14 set = primary IDE channel has 80-pin cable.
*/
-static unsigned int __init ata66_svwks_dell (ide_hwif_t *hwif)
+static unsigned int __devinit ata66_svwks_dell (ide_hwif_t *hwif)
{
struct pci_dev *dev = hwif->pci_dev;
if (dev->subsystem_vendor == PCI_VENDOR_ID_DELL &&
@@ -472,7 +472,7 @@ static unsigned int __init ata66_svwks_dell (ide_hwif_t *hwif)
*
* WARNING: this only works on Alpine hardware!
*/
-static unsigned int __init ata66_svwks_cobalt (ide_hwif_t *hwif)
+static unsigned int __devinit ata66_svwks_cobalt (ide_hwif_t *hwif)
{
struct pci_dev *dev = hwif->pci_dev;
if (dev->subsystem_vendor == PCI_VENDOR_ID_SUN &&
@@ -483,7 +483,7 @@ static unsigned int __init ata66_svwks_cobalt (ide_hwif_t *hwif)
return 0;
}
-static unsigned int __init ata66_svwks (ide_hwif_t *hwif)
+static unsigned int __devinit ata66_svwks (ide_hwif_t *hwif)
{
struct pci_dev *dev = hwif->pci_dev;
@@ -573,7 +573,7 @@ static int __devinit init_setup_svwks (struct pci_dev *dev, ide_pci_device_t *d)
return ide_setup_pci_device(dev, d);
}
-static int __init init_setup_csb6 (struct pci_dev *dev, ide_pci_device_t *d)
+static int __devinit init_setup_csb6 (struct pci_dev *dev, ide_pci_device_t *d)
{
if (!(PCI_FUNC(dev->devfn) & 1)) {
d->bootable = NEVER_BOARD;
diff --git a/drivers/ide/pci/sgiioc4.c b/drivers/ide/pci/sgiioc4.c
index 4651a22bf12..af526b671c4 100644
--- a/drivers/ide/pci/sgiioc4.c
+++ b/drivers/ide/pci/sgiioc4.c
@@ -34,7 +34,7 @@
#include <linux/mm.h>
#include <linux/ioport.h>
#include <linux/blkdev.h>
-#include <linux/ioc4_common.h>
+#include <linux/ioc4.h>
#include <asm/io.h>
#include <linux/ide.h>
@@ -715,14 +715,34 @@ static ide_pci_device_t sgiioc4_chipsets[] __devinitdata = {
};
int
-ioc4_ide_attach_one(struct pci_dev *dev, const struct pci_device_id *id)
+ioc4_ide_attach_one(struct ioc4_driver_data *idd)
{
- return pci_init_sgiioc4(dev, &sgiioc4_chipsets[id->driver_data]);
+ return pci_init_sgiioc4(idd->idd_pdev,
+ &sgiioc4_chipsets[idd->idd_pci_id->driver_data]);
}
+static struct ioc4_submodule ioc4_ide_submodule = {
+ .is_name = "IOC4_ide",
+ .is_owner = THIS_MODULE,
+ .is_probe = ioc4_ide_attach_one,
+/* .is_remove = ioc4_ide_remove_one, */
+};
+
+static int __devinit
+ioc4_ide_init(void)
+{
+ return ioc4_register_submodule(&ioc4_ide_submodule);
+}
+
+static void __devexit
+ioc4_ide_exit(void)
+{
+ ioc4_unregister_submodule(&ioc4_ide_submodule);
+}
+
+module_init(ioc4_ide_init);
+module_exit(ioc4_ide_exit);
MODULE_AUTHOR("Aniket Malatpure - Silicon Graphics Inc. (SGI)");
MODULE_DESCRIPTION("IDE PCI driver module for SGI IOC4 Base-IO Card");
MODULE_LICENSE("GPL");
-
-EXPORT_SYMBOL(ioc4_ide_attach_one);
diff --git a/drivers/ide/ppc/pmac.c b/drivers/ide/ppc/pmac.c
index 569f1676744..818380b5fd2 100644
--- a/drivers/ide/ppc/pmac.c
+++ b/drivers/ide/ppc/pmac.c
@@ -1324,9 +1324,9 @@ pmac_ide_setup_device(pmac_ide_hwif_t *pmif, ide_hwif_t *hwif)
/* XXX FIXME: Media bay stuff need re-organizing */
if (np->parent && np->parent->name
&& strcasecmp(np->parent->name, "media-bay") == 0) {
-#ifdef CONFIG_PMAC_PBOOK
+#ifdef CONFIG_PMAC_MEDIABAY
media_bay_set_ide_infos(np->parent, pmif->regbase, pmif->irq, hwif->index);
-#endif /* CONFIG_PMAC_PBOOK */
+#endif /* CONFIG_PMAC_MEDIABAY */
pmif->mediabay = 1;
if (!bidp)
pmif->aapl_bus_id = 1;
@@ -1382,10 +1382,10 @@ pmac_ide_setup_device(pmac_ide_hwif_t *pmif, ide_hwif_t *hwif)
hwif->index, model_name[pmif->kind], pmif->aapl_bus_id,
pmif->mediabay ? " (mediabay)" : "", hwif->irq);
-#ifdef CONFIG_PMAC_PBOOK
+#ifdef CONFIG_PMAC_MEDIABAY
if (pmif->mediabay && check_media_bay_by_base(pmif->regbase, MB_CD) == 0)
hwif->noprobe = 0;
-#endif /* CONFIG_PMAC_PBOOK */
+#endif /* CONFIG_PMAC_MEDIABAY */
hwif->sg_max_nents = MAX_DCMDS;
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-12-30 21:12:57 +0000