diff options
Diffstat (limited to 'drivers/iio/gyro/adis16260.c')
| -rw-r--r-- | drivers/iio/gyro/adis16260.c | 428 |
1 files changed, 428 insertions, 0 deletions
diff --git a/drivers/iio/gyro/adis16260.c b/drivers/iio/gyro/adis16260.c new file mode 100644 index 00000000000..b4cf800717a --- /dev/null +++ b/drivers/iio/gyro/adis16260.c @@ -0,0 +1,428 @@ +/* + * ADIS16260/ADIS16265 Programmable Digital Gyroscope Sensor Driver + * + * Copyright 2010 Analog Devices Inc. + * + * Licensed under the GPL-2 or later. + */ + +#include <linux/interrupt.h> +#include <linux/mutex.h> +#include <linux/device.h> +#include <linux/kernel.h> +#include <linux/spi/spi.h> +#include <linux/sysfs.h> +#include <linux/module.h> + +#include <linux/iio/iio.h> +#include <linux/iio/sysfs.h> +#include <linux/iio/buffer.h> +#include <linux/iio/imu/adis.h> + +#define ADIS16260_STARTUP_DELAY 220 /* ms */ + +#define ADIS16260_FLASH_CNT 0x00 /* Flash memory write count */ +#define ADIS16260_SUPPLY_OUT 0x02 /* Power supply measurement */ +#define ADIS16260_GYRO_OUT 0x04 /* X-axis gyroscope output */ +#define ADIS16260_AUX_ADC 0x0A /* analog input channel measurement */ +#define ADIS16260_TEMP_OUT 0x0C /* internal temperature measurement */ +#define ADIS16260_ANGL_OUT 0x0E /* angle displacement */ +#define ADIS16260_GYRO_OFF 0x14 /* Calibration, offset/bias adjustment */ +#define ADIS16260_GYRO_SCALE 0x16 /* Calibration, scale adjustment */ +#define ADIS16260_ALM_MAG1 0x20 /* Alarm 1 magnitude/polarity setting */ +#define ADIS16260_ALM_MAG2 0x22 /* Alarm 2 magnitude/polarity setting */ +#define ADIS16260_ALM_SMPL1 0x24 /* Alarm 1 dynamic rate of change setting */ +#define ADIS16260_ALM_SMPL2 0x26 /* Alarm 2 dynamic rate of change setting */ +#define ADIS16260_ALM_CTRL 0x28 /* Alarm control */ +#define ADIS16260_AUX_DAC 0x30 /* Auxiliary DAC data */ +#define ADIS16260_GPIO_CTRL 0x32 /* Control, digital I/O line */ +#define ADIS16260_MSC_CTRL 0x34 /* Control, data ready, self-test settings */ +#define ADIS16260_SMPL_PRD 0x36 /* Control, internal sample rate */ +#define ADIS16260_SENS_AVG 0x38 /* Control, dynamic range, filtering */ +#define ADIS16260_SLP_CNT 0x3A /* Control, sleep mode initiation */ +#define ADIS16260_DIAG_STAT 0x3C /* Diagnostic, error flags */ +#define ADIS16260_GLOB_CMD 0x3E /* Control, global commands */ +#define ADIS16260_LOT_ID1 0x52 /* Lot Identification Code 1 */ +#define ADIS16260_LOT_ID2 0x54 /* Lot Identification Code 2 */ +#define ADIS16260_PROD_ID 0x56 /* Product identifier; + * convert to decimal = 16,265/16,260 */ +#define ADIS16260_SERIAL_NUM 0x58 /* Serial number */ + +#define ADIS16260_ERROR_ACTIVE (1<<14) +#define ADIS16260_NEW_DATA (1<<15) + +/* MSC_CTRL */ +#define ADIS16260_MSC_CTRL_MEM_TEST (1<<11) +/* Internal self-test enable */ +#define ADIS16260_MSC_CTRL_INT_SELF_TEST (1<<10) +#define ADIS16260_MSC_CTRL_NEG_SELF_TEST (1<<9) +#define ADIS16260_MSC_CTRL_POS_SELF_TEST (1<<8) +#define ADIS16260_MSC_CTRL_DATA_RDY_EN (1<<2) +#define ADIS16260_MSC_CTRL_DATA_RDY_POL_HIGH (1<<1) +#define ADIS16260_MSC_CTRL_DATA_RDY_DIO2 (1<<0) + +/* SMPL_PRD */ +/* Time base (tB): 0 = 1.953 ms, 1 = 60.54 ms */ +#define ADIS16260_SMPL_PRD_TIME_BASE (1<<7) +#define ADIS16260_SMPL_PRD_DIV_MASK 0x7F + +/* SLP_CNT */ +#define ADIS16260_SLP_CNT_POWER_OFF 0x80 + +/* DIAG_STAT */ +#define ADIS16260_DIAG_STAT_ALARM2 (1<<9) +#define ADIS16260_DIAG_STAT_ALARM1 (1<<8) +#define ADIS16260_DIAG_STAT_FLASH_CHK_BIT 6 +#define ADIS16260_DIAG_STAT_SELF_TEST_BIT 5 +#define ADIS16260_DIAG_STAT_OVERFLOW_BIT 4 +#define ADIS16260_DIAG_STAT_SPI_FAIL_BIT 3 +#define ADIS16260_DIAG_STAT_FLASH_UPT_BIT 2 +#define ADIS16260_DIAG_STAT_POWER_HIGH_BIT 1 +#define ADIS16260_DIAG_STAT_POWER_LOW_BIT 0 + +/* GLOB_CMD */ +#define ADIS16260_GLOB_CMD_SW_RESET (1<<7) +#define ADIS16260_GLOB_CMD_FLASH_UPD (1<<3) +#define ADIS16260_GLOB_CMD_DAC_LATCH (1<<2) +#define ADIS16260_GLOB_CMD_FAC_CALIB (1<<1) +#define ADIS16260_GLOB_CMD_AUTO_NULL (1<<0) + +#define ADIS16260_SPI_SLOW (u32)(300 * 1000) +#define ADIS16260_SPI_BURST (u32)(1000 * 1000) +#define ADIS16260_SPI_FAST (u32)(2000 * 1000) + +/* At the moment triggers are only used for ring buffer + * filling. This may change! + */ + +#define ADIS16260_SCAN_GYRO 0 +#define ADIS16260_SCAN_SUPPLY 1 +#define ADIS16260_SCAN_AUX_ADC 2 +#define ADIS16260_SCAN_TEMP 3 +#define ADIS16260_SCAN_ANGL 4 + +static ssize_t adis16260_read_frequency(struct device *dev, + struct device_attribute *attr, + char *buf) +{ + struct iio_dev *indio_dev = dev_to_iio_dev(dev); + struct adis *adis = iio_priv(indio_dev); + int ret, len = 0; + u16 t; + int sps; + ret = adis_read_reg_16(adis, ADIS16260_SMPL_PRD, &t); + if (ret) + return ret; + + if (spi_get_device_id(adis->spi)->driver_data) /* If an adis16251 */ + sps = (t & ADIS16260_SMPL_PRD_TIME_BASE) ? 8 : 256; + else + sps = (t & ADIS16260_SMPL_PRD_TIME_BASE) ? 66 : 2048; + sps /= (t & ADIS16260_SMPL_PRD_DIV_MASK) + 1; + len = sprintf(buf, "%d\n", sps); + return len; +} + +static ssize_t adis16260_write_frequency(struct device *dev, + struct device_attribute *attr, + const char *buf, + size_t len) +{ + struct iio_dev *indio_dev = dev_to_iio_dev(dev); + struct adis *adis = iio_priv(indio_dev); + unsigned int val; + int ret; + u8 t; + + ret = kstrtouint(buf, 10, &val); + if (ret) + return ret; + + mutex_lock(&indio_dev->mlock); + if (spi_get_device_id(adis->spi)->driver_data) + t = 256 / val; + else + t = 2048 / val; + + if (t > ADIS16260_SMPL_PRD_DIV_MASK) + t = ADIS16260_SMPL_PRD_DIV_MASK; + else if (t > 0) + t--; + + if (t >= 0x0A) + adis->spi->max_speed_hz = ADIS16260_SPI_SLOW; + else + adis->spi->max_speed_hz = ADIS16260_SPI_FAST; + ret = adis_write_reg_8(adis, ADIS16260_SMPL_PRD, t); + + mutex_unlock(&indio_dev->mlock); + + return ret ? ret : len; +} + +/* Power down the device */ +static int adis16260_stop_device(struct iio_dev *indio_dev) +{ + struct adis *adis = iio_priv(indio_dev); + int ret; + u16 val = ADIS16260_SLP_CNT_POWER_OFF; + + ret = adis_write_reg_16(adis, ADIS16260_SLP_CNT, val); + if (ret) + dev_err(&indio_dev->dev, "problem with turning device off: SLP_CNT"); + + return ret; +} + +static IIO_DEV_ATTR_SAMP_FREQ(S_IWUSR | S_IRUGO, + adis16260_read_frequency, + adis16260_write_frequency); + +static const struct iio_chan_spec adis16260_channels[] = { + ADIS_GYRO_CHAN(X, ADIS16260_GYRO_OUT, ADIS16260_SCAN_GYRO, + BIT(IIO_CHAN_INFO_CALIBBIAS) | + BIT(IIO_CHAN_INFO_CALIBSCALE), 14), + ADIS_INCLI_CHAN(X, ADIS16260_ANGL_OUT, ADIS16260_SCAN_ANGL, 0, 14), + ADIS_TEMP_CHAN(ADIS16260_TEMP_OUT, ADIS16260_SCAN_TEMP, 12), + ADIS_SUPPLY_CHAN(ADIS16260_SUPPLY_OUT, ADIS16260_SCAN_SUPPLY, 12), + ADIS_AUX_ADC_CHAN(ADIS16260_AUX_ADC, ADIS16260_SCAN_AUX_ADC, 12), + IIO_CHAN_SOFT_TIMESTAMP(5), +}; + +static const u8 adis16260_addresses[][2] = { + [ADIS16260_SCAN_GYRO] = { ADIS16260_GYRO_OFF, ADIS16260_GYRO_SCALE }, +}; + +static int adis16260_read_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, + int *val, int *val2, + long mask) +{ + struct adis *adis = iio_priv(indio_dev); + int ret; + u8 addr; + s16 val16; + + switch (mask) { + case IIO_CHAN_INFO_RAW: + return adis_single_conversion(indio_dev, chan, + ADIS16260_ERROR_ACTIVE, val); + case IIO_CHAN_INFO_SCALE: + switch (chan->type) { + case IIO_ANGL_VEL: + *val = 0; + if (spi_get_device_id(adis->spi)->driver_data) { + /* 0.01832 degree / sec */ + *val2 = IIO_DEGREE_TO_RAD(18320); + } else { + /* 0.07326 degree / sec */ + *val2 = IIO_DEGREE_TO_RAD(73260); + } + return IIO_VAL_INT_PLUS_MICRO; + case IIO_INCLI: + *val = 0; + *val2 = IIO_DEGREE_TO_RAD(36630); + return IIO_VAL_INT_PLUS_MICRO; + case IIO_VOLTAGE: + if (chan->channel == 0) { + *val = 1; + *val2 = 831500; /* 1.8315 mV */ + } else { + *val = 0; + *val2 = 610500; /* 610.5 uV */ + } + return IIO_VAL_INT_PLUS_MICRO; + case IIO_TEMP: + *val = 145; + *val2 = 300000; /* 0.1453 C */ + return IIO_VAL_INT_PLUS_MICRO; + default: + return -EINVAL; + } + break; + case IIO_CHAN_INFO_OFFSET: + *val = 250000 / 1453; /* 25 C = 0x00 */ + return IIO_VAL_INT; + case IIO_CHAN_INFO_CALIBBIAS: + addr = adis16260_addresses[chan->scan_index][0]; + ret = adis_read_reg_16(adis, addr, &val16); + if (ret) + return ret; + + *val = sign_extend32(val16, 11); + return IIO_VAL_INT; + case IIO_CHAN_INFO_CALIBSCALE: + addr = adis16260_addresses[chan->scan_index][1]; + ret = adis_read_reg_16(adis, addr, &val16); + if (ret) + return ret; + + *val = val16; + return IIO_VAL_INT; + } + return -EINVAL; +} + +static int adis16260_write_raw(struct iio_dev *indio_dev, + struct iio_chan_spec const *chan, + int val, + int val2, + long mask) +{ + struct adis *adis = iio_priv(indio_dev); + u8 addr; + + switch (mask) { + case IIO_CHAN_INFO_CALIBBIAS: + if (val < -2048 || val >= 2048) + return -EINVAL; + + addr = adis16260_addresses[chan->scan_index][0]; + return adis_write_reg_16(adis, addr, val); + case IIO_CHAN_INFO_CALIBSCALE: + if (val < 0 || val >= 4096) + return -EINVAL; + + addr = adis16260_addresses[chan->scan_index][1]; + return adis_write_reg_16(adis, addr, val); + } + return -EINVAL; +} + +static struct attribute *adis16260_attributes[] = { + &iio_dev_attr_sampling_frequency.dev_attr.attr, + NULL +}; + +static const struct attribute_group adis16260_attribute_group = { + .attrs = adis16260_attributes, +}; + +static const struct iio_info adis16260_info = { + .attrs = &adis16260_attribute_group, + .read_raw = &adis16260_read_raw, + .write_raw = &adis16260_write_raw, + .update_scan_mode = adis_update_scan_mode, + .driver_module = THIS_MODULE, +}; + +static const char * const adis1620_status_error_msgs[] = { + [ADIS16260_DIAG_STAT_FLASH_CHK_BIT] = "Flash checksum error", + [ADIS16260_DIAG_STAT_SELF_TEST_BIT] = "Self test error", + [ADIS16260_DIAG_STAT_OVERFLOW_BIT] = "Sensor overrange", + [ADIS16260_DIAG_STAT_SPI_FAIL_BIT] = "SPI failure", + [ADIS16260_DIAG_STAT_FLASH_UPT_BIT] = "Flash update failed", + [ADIS16260_DIAG_STAT_POWER_HIGH_BIT] = "Power supply above 5.25", + [ADIS16260_DIAG_STAT_POWER_LOW_BIT] = "Power supply below 4.75", +}; + +static const struct adis_data adis16260_data = { + .write_delay = 30, + .read_delay = 30, + .msc_ctrl_reg = ADIS16260_MSC_CTRL, + .glob_cmd_reg = ADIS16260_GLOB_CMD, + .diag_stat_reg = ADIS16260_DIAG_STAT, + + .self_test_mask = ADIS16260_MSC_CTRL_MEM_TEST, + .startup_delay = ADIS16260_STARTUP_DELAY, + + .status_error_msgs = adis1620_status_error_msgs, + .status_error_mask = BIT(ADIS16260_DIAG_STAT_FLASH_CHK_BIT) | + BIT(ADIS16260_DIAG_STAT_SELF_TEST_BIT) | + BIT(ADIS16260_DIAG_STAT_OVERFLOW_BIT) | + BIT(ADIS16260_DIAG_STAT_SPI_FAIL_BIT) | + BIT(ADIS16260_DIAG_STAT_FLASH_UPT_BIT) | + BIT(ADIS16260_DIAG_STAT_POWER_HIGH_BIT) | + BIT(ADIS16260_DIAG_STAT_POWER_LOW_BIT), +}; + +static int adis16260_probe(struct spi_device *spi) +{ + struct iio_dev *indio_dev; + struct adis *adis; + int ret; + + /* setup the industrialio driver allocated elements */ + indio_dev = iio_device_alloc(sizeof(*adis)); + if (indio_dev == NULL) { + ret = -ENOMEM; + goto error_ret; + } + adis = iio_priv(indio_dev); + /* this is only used for removal purposes */ + spi_set_drvdata(spi, indio_dev); + + indio_dev->name = spi_get_device_id(spi)->name; + indio_dev->dev.parent = &spi->dev; + indio_dev->info = &adis16260_info; + indio_dev->channels = adis16260_channels; + indio_dev->num_channels = ARRAY_SIZE(adis16260_channels); + indio_dev->modes = INDIO_DIRECT_MODE; + + ret = adis_init(adis, indio_dev, spi, &adis16260_data); + if (ret) + goto error_free_dev; + + ret = adis_setup_buffer_and_trigger(adis, indio_dev, NULL); + if (ret) + goto error_free_dev; + + /* Get the device into a sane initial state */ + ret = adis_initial_startup(adis); + if (ret) + goto error_cleanup_buffer_trigger; + ret = iio_device_register(indio_dev); + if (ret) + goto error_cleanup_buffer_trigger; + + return 0; + +error_cleanup_buffer_trigger: + adis_cleanup_buffer_and_trigger(adis, indio_dev); +error_free_dev: + iio_device_free(indio_dev); +error_ret: + return ret; +} + +static int adis16260_remove(struct spi_device *spi) +{ + struct iio_dev *indio_dev = spi_get_drvdata(spi); + struct adis *adis = iio_priv(indio_dev); + + iio_device_unregister(indio_dev); + adis16260_stop_device(indio_dev); + adis_cleanup_buffer_and_trigger(adis, indio_dev); + iio_device_free(indio_dev); + + return 0; +} + +/* + * These parts do not need to be differentiated until someone adds + * support for the on chip filtering. + */ +static const struct spi_device_id adis16260_id[] = { + {"adis16260", 0}, + {"adis16265", 0}, + {"adis16250", 0}, + {"adis16255", 0}, + {"adis16251", 1}, + {} +}; +MODULE_DEVICE_TABLE(spi, adis16260_id); + +static struct spi_driver adis16260_driver = { + .driver = { + .name = "adis16260", + .owner = THIS_MODULE, + }, + .probe = adis16260_probe, + .remove = adis16260_remove, + .id_table = adis16260_id, +}; +module_spi_driver(adis16260_driver); + +MODULE_AUTHOR("Barry Song <21cnbao@gmail.com>"); +MODULE_DESCRIPTION("Analog Devices ADIS16260/5 Digital Gyroscope Sensor"); +MODULE_LICENSE("GPL v2"); |