diff options
Diffstat (limited to 'drivers/infiniband/hw/ipath/ipath_iba6120.c')
| -rw-r--r-- | drivers/infiniband/hw/ipath/ipath_iba6120.c | 203 |
1 files changed, 156 insertions, 47 deletions
diff --git a/drivers/infiniband/hw/ipath/ipath_iba6120.c b/drivers/infiniband/hw/ipath/ipath_iba6120.c index c7a2f50824c..421cc2af891 100644 --- a/drivers/infiniband/hw/ipath/ipath_iba6120.c +++ b/drivers/infiniband/hw/ipath/ipath_iba6120.c @@ -1,5 +1,5 @@ /* - * Copyright (c) 2006, 2007 QLogic Corporation. All rights reserved. + * Copyright (c) 2006, 2007, 2008 QLogic Corporation. All rights reserved. * Copyright (c) 2003, 2004, 2005, 2006 PathScale, Inc. All rights reserved. * * This software is available to you under a choice of one of two @@ -38,7 +38,7 @@ #include <linux/interrupt.h> #include <linux/pci.h> #include <linux/delay.h> - +#include <rdma/ib_verbs.h> #include "ipath_kernel.h" #include "ipath_registers.h" @@ -311,9 +311,14 @@ static const struct ipath_cregs ipath_pe_cregs = { .cr_ibsymbolerrcnt = IPATH_CREG_OFFSET(IBSymbolErrCnt) }; +/* kr_control bits */ +#define INFINIPATH_C_RESET 1U + /* kr_intstatus, kr_intclear, kr_intmask bits */ #define INFINIPATH_I_RCVURG_MASK ((1U<<5)-1) +#define INFINIPATH_I_RCVURG_SHIFT 0 #define INFINIPATH_I_RCVAVAIL_MASK ((1U<<5)-1) +#define INFINIPATH_I_RCVAVAIL_SHIFT 12 /* kr_hwerrclear, kr_hwerrmask, kr_hwerrstatus, bits */ #define INFINIPATH_HWE_PCIEMEMPARITYERR_MASK 0x000000000000003fULL @@ -338,6 +343,9 @@ static const struct ipath_cregs ipath_pe_cregs = { #define INFINIPATH_EXTS_MEMBIST_ENDTEST 0x0000000000004000 #define INFINIPATH_EXTS_MEMBIST_FOUND 0x0000000000008000 +/* kr_xgxsconfig bits */ +#define INFINIPATH_XGXS_RESET 0x5ULL + #define _IPATH_GPIO_SDA_NUM 1 #define _IPATH_GPIO_SCL_NUM 0 @@ -346,6 +354,16 @@ static const struct ipath_cregs ipath_pe_cregs = { #define IPATH_GPIO_SCL (1ULL << \ (_IPATH_GPIO_SCL_NUM+INFINIPATH_EXTC_GPIOOE_SHIFT)) +#define INFINIPATH_RT_BUFSIZE_MASK 0xe0000000ULL +#define INFINIPATH_RT_BUFSIZE_SHIFTVAL(tid) \ + ((((tid) & INFINIPATH_RT_BUFSIZE_MASK) >> 29) + 11 - 1) +#define INFINIPATH_RT_BUFSIZE(tid) (1 << INFINIPATH_RT_BUFSIZE_SHIFTVAL(tid)) +#define INFINIPATH_RT_IS_VALID(tid) \ + (((tid) & INFINIPATH_RT_BUFSIZE_MASK) && \ + ((((tid) & INFINIPATH_RT_BUFSIZE_MASK) != INFINIPATH_RT_BUFSIZE_MASK))) +#define INFINIPATH_RT_ADDR_MASK 0x1FFFFFFFULL /* 29 bits valid */ +#define INFINIPATH_RT_ADDR_SHIFT 10 + #define INFINIPATH_R_INTRAVAIL_SHIFT 16 #define INFINIPATH_R_TAILUPD_SHIFT 31 @@ -372,6 +390,8 @@ static const struct ipath_hwerror_msgs ipath_6120_hwerror_msgs[] = { #define TXE_PIO_PARITY ((INFINIPATH_HWE_TXEMEMPARITYERR_PIOBUF | \ INFINIPATH_HWE_TXEMEMPARITYERR_PIOPBC) \ << INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT) +#define RXE_EAGER_PARITY (INFINIPATH_HWE_RXEMEMPARITYERR_EAGERTID \ + << INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT) static void ipath_pe_put_tid_2(struct ipath_devdata *, u64 __iomem *, u32, unsigned long); @@ -450,10 +470,8 @@ static void ipath_pe_handle_hwerrors(struct ipath_devdata *dd, char *msg, * make sure we get this much out, unless told to be quiet, * or it's occurred within the last 5 seconds */ - if ((hwerrs & ~(dd->ipath_lasthwerror | - ((INFINIPATH_HWE_TXEMEMPARITYERR_PIOBUF | - INFINIPATH_HWE_TXEMEMPARITYERR_PIOPBC) - << INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT))) || + if ((hwerrs & ~(dd->ipath_lasthwerror | TXE_PIO_PARITY | + RXE_EAGER_PARITY)) || (ipath_debug & __IPATH_VERBDBG)) dev_info(&dd->pcidev->dev, "Hardware error: hwerr=0x%llx " "(cleared)\n", (unsigned long long) hwerrs); @@ -465,7 +483,7 @@ static void ipath_pe_handle_hwerrors(struct ipath_devdata *dd, char *msg, (hwerrs & ~dd->ipath_hwe_bitsextant)); ctrl = ipath_read_kreg32(dd, dd->ipath_kregs->kr_control); - if (ctrl & INFINIPATH_C_FREEZEMODE) { + if ((ctrl & INFINIPATH_C_FREEZEMODE) && !ipath_diag_inuse) { /* * parity errors in send memory are recoverable, * just cancel the send (if indicated in * sendbuffererror), @@ -540,12 +558,40 @@ static void ipath_pe_handle_hwerrors(struct ipath_devdata *dd, char *msg, dd->ipath_hwerrmask); } - if (*msg) + if (hwerrs) { + /* + * if any set that we aren't ignoring; only + * make the complaint once, in case it's stuck + * or recurring, and we get here multiple + * times. + */ ipath_dev_err(dd, "%s hardware error\n", msg); - if (isfatal && !ipath_diag_inuse && dd->ipath_freezemsg) { + if (dd->ipath_flags & IPATH_INITTED) { + ipath_set_linkstate(dd, IPATH_IB_LINKDOWN); + ipath_setup_pe_setextled(dd, + INFINIPATH_IBCS_L_STATE_DOWN, + INFINIPATH_IBCS_LT_STATE_DISABLED); + ipath_dev_err(dd, "Fatal Hardware Error (freeze " + "mode), no longer usable, SN %.16s\n", + dd->ipath_serial); + isfatal = 1; + } + *dd->ipath_statusp &= ~IPATH_STATUS_IB_READY; + /* mark as having had error */ + *dd->ipath_statusp |= IPATH_STATUS_HWERROR; /* - * for /sys status file ; if no trailing } is copied, we'll - * know it was truncated. + * mark as not usable, at a minimum until driver + * is reloaded, probably until reboot, since no + * other reset is possible. + */ + dd->ipath_flags &= ~IPATH_INITTED; + } else + *msg = 0; /* recovered from all of them */ + + if (isfatal && !ipath_diag_inuse && dd->ipath_freezemsg && msg) { + /* + * for /sys status file ; if no trailing brace is copied, + * we'll know it was truncated. */ snprintf(dd->ipath_freezemsg, dd->ipath_freezelen, "{%s}", msg); @@ -610,7 +656,6 @@ static int ipath_pe_boardname(struct ipath_devdata *dd, char *name, dd->ipath_f_put_tid = ipath_pe_put_tid_2; } - /* * set here, not in ipath_init_*_funcs because we have to do * it after we can read chip registers. @@ -838,7 +883,7 @@ static void ipath_setup_pe_setextled(struct ipath_devdata *dd, u64 lst, extctl = dd->ipath_extctrl & ~(INFINIPATH_EXTC_LED1PRIPORT_ON | INFINIPATH_EXTC_LED2PRIPORT_ON); - if (ltst & INFINIPATH_IBCS_LT_STATE_LINKUP) + if (ltst == INFINIPATH_IBCS_LT_STATE_LINKUP) extctl |= INFINIPATH_EXTC_LED2PRIPORT_ON; if (lst == INFINIPATH_IBCS_L_STATE_ACTIVE) extctl |= INFINIPATH_EXTC_LED1PRIPORT_ON; @@ -863,6 +908,62 @@ static void ipath_setup_pe_cleanup(struct ipath_devdata *dd) pci_disable_msi(dd->pcidev); } +static void ipath_6120_pcie_params(struct ipath_devdata *dd) +{ + u16 linkstat, speed; + int pos; + + pos = pci_find_capability(dd->pcidev, PCI_CAP_ID_EXP); + if (!pos) { + ipath_dev_err(dd, "Can't find PCI Express capability!\n"); + goto bail; + } + + pci_read_config_word(dd->pcidev, pos + PCI_EXP_LNKSTA, + &linkstat); + /* + * speed is bits 0-4, linkwidth is bits 4-8 + * no defines for them in headers + */ + speed = linkstat & 0xf; + linkstat >>= 4; + linkstat &= 0x1f; + dd->ipath_lbus_width = linkstat; + + switch (speed) { + case 1: + dd->ipath_lbus_speed = 2500; /* Gen1, 2.5GHz */ + break; + case 2: + dd->ipath_lbus_speed = 5000; /* Gen1, 5GHz */ + break; + default: /* not defined, assume gen1 */ + dd->ipath_lbus_speed = 2500; + break; + } + + if (linkstat < 8) + ipath_dev_err(dd, + "PCIe width %u (x8 HCA), performance reduced\n", + linkstat); + else + ipath_cdbg(VERBOSE, "PCIe speed %u width %u (x8 HCA)\n", + dd->ipath_lbus_speed, linkstat); + + if (speed != 1) + ipath_dev_err(dd, + "PCIe linkspeed %u is incorrect; " + "should be 1 (2500)!\n", speed); +bail: + /* fill in string, even on errors */ + snprintf(dd->ipath_lbus_info, sizeof(dd->ipath_lbus_info), + "PCIe,%uMHz,x%u\n", + dd->ipath_lbus_speed, + dd->ipath_lbus_width); + + return; +} + /** * ipath_setup_pe_config - setup PCIe config related stuff * @dd: the infinipath device @@ -920,19 +1021,8 @@ static int ipath_setup_pe_config(struct ipath_devdata *dd, } else ipath_dev_err(dd, "Can't find MSI capability, " "can't save MSI settings for reset\n"); - if ((pos = pci_find_capability(dd->pcidev, PCI_CAP_ID_EXP))) { - u16 linkstat; - pci_read_config_word(dd->pcidev, pos + PCI_EXP_LNKSTA, - &linkstat); - linkstat >>= 4; - linkstat &= 0x1f; - if (linkstat != 8) - ipath_dev_err(dd, "PCIe width %u, " - "performance reduced\n", linkstat); - } - else - ipath_dev_err(dd, "Can't find PCI Express " - "capability!\n"); + + ipath_6120_pcie_params(dd); dd->ipath_link_width_supported = IB_WIDTH_1X | IB_WIDTH_4X; dd->ipath_link_speed_supported = IPATH_IB_SDR; @@ -1065,10 +1155,7 @@ static void ipath_init_pe_variables(struct ipath_devdata *dd) INFINIPATH_HWE_RXEMEMPARITYERR_MASK << INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT; - dd->ipath_eep_st_masks[2].errs_to_log = - INFINIPATH_E_INVALIDADDR | INFINIPATH_E_RESET; - - + dd->ipath_eep_st_masks[2].errs_to_log = INFINIPATH_E_RESET; dd->delay_mult = 2; /* SDR, 4X, can't change */ } @@ -1142,6 +1229,9 @@ static int ipath_setup_pe_reset(struct ipath_devdata *dd) u64 val; int i; int ret; + u16 cmdval; + + pci_read_config_word(dd->pcidev, PCI_COMMAND, &cmdval); /* Use ERROR so it shows up in logs, etc. */ ipath_dev_err(dd, "Resetting InfiniPath unit %u\n", dd->ipath_unit); @@ -1169,10 +1259,14 @@ static int ipath_setup_pe_reset(struct ipath_devdata *dd) ipath_dev_err(dd, "rewrite of BAR1 failed: %d\n", r); /* now re-enable memory access */ + pci_write_config_word(dd->pcidev, PCI_COMMAND, cmdval); if ((r = pci_enable_device(dd->pcidev))) ipath_dev_err(dd, "pci_enable_device failed after " "reset: %d\n", r); - /* whether it worked or not, mark as present, again */ + /* + * whether it fully enabled or not, mark as present, + * again (but not INITTED) + */ dd->ipath_flags |= IPATH_PRESENT; val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_revision); if (val == dd->ipath_revision) { @@ -1190,6 +1284,8 @@ static int ipath_setup_pe_reset(struct ipath_devdata *dd) ret = 0; /* failed */ bail: + if (ret) + ipath_6120_pcie_params(dd); return ret; } @@ -1209,16 +1305,21 @@ static void ipath_pe_put_tid(struct ipath_devdata *dd, u64 __iomem *tidptr, { u32 __iomem *tidp32 = (u32 __iomem *)tidptr; unsigned long flags = 0; /* keep gcc quiet */ + int tidx; + spinlock_t *tidlockp; + + if (!dd->ipath_kregbase) + return; if (pa != dd->ipath_tidinvalid) { if (pa & ((1U << 11) - 1)) { dev_info(&dd->pcidev->dev, "BUG: physaddr %lx " - "not 4KB aligned!\n", pa); + "not 2KB aligned!\n", pa); return; } pa >>= 11; /* paranoia check */ - if (pa & (7<<29)) + if (pa & ~INFINIPATH_RT_ADDR_MASK) ipath_dev_err(dd, "BUG: Physical page address 0x%lx " "has bits set in 31-29\n", pa); @@ -1238,14 +1339,22 @@ static void ipath_pe_put_tid(struct ipath_devdata *dd, u64 __iomem *tidptr, * call can be done from interrupt level for the port 0 eager TIDs, * so we have to use irqsave locks. */ - spin_lock_irqsave(&dd->ipath_tid_lock, flags); + /* + * Assumes tidptr always > ipath_egrtidbase + * if type == RCVHQ_RCV_TYPE_EAGER. + */ + tidx = tidptr - dd->ipath_egrtidbase; + + tidlockp = (type == RCVHQ_RCV_TYPE_EAGER && tidx < dd->ipath_rcvegrcnt) + ? &dd->ipath_kernel_tid_lock : &dd->ipath_user_tid_lock; + spin_lock_irqsave(tidlockp, flags); ipath_write_kreg(dd, dd->ipath_kregs->kr_scratch, 0xfeeddeaf); - if (dd->ipath_kregbase) - writel(pa, tidp32); + writel(pa, tidp32); ipath_write_kreg(dd, dd->ipath_kregs->kr_scratch, 0xdeadbeef); mmiowb(); - spin_unlock_irqrestore(&dd->ipath_tid_lock, flags); + spin_unlock_irqrestore(tidlockp, flags); } + /** * ipath_pe_put_tid_2 - write a TID in chip, Revision 2 or higher * @dd: the infinipath device @@ -1261,6 +1370,10 @@ static void ipath_pe_put_tid_2(struct ipath_devdata *dd, u64 __iomem *tidptr, u32 type, unsigned long pa) { u32 __iomem *tidp32 = (u32 __iomem *)tidptr; + u32 tidx; + + if (!dd->ipath_kregbase) + return; if (pa != dd->ipath_tidinvalid) { if (pa & ((1U << 11) - 1)) { @@ -1270,7 +1383,7 @@ static void ipath_pe_put_tid_2(struct ipath_devdata *dd, u64 __iomem *tidptr, } pa >>= 11; /* paranoia check */ - if (pa & (7<<29)) + if (pa & ~INFINIPATH_RT_ADDR_MASK) ipath_dev_err(dd, "BUG: Physical page address 0x%lx " "has bits set in 31-29\n", pa); @@ -1280,8 +1393,8 @@ static void ipath_pe_put_tid_2(struct ipath_devdata *dd, u64 __iomem *tidptr, else /* for now, always full 4KB page */ pa |= 2 << 29; } - if (dd->ipath_kregbase) - writel(pa, tidp32); + tidx = tidptr - dd->ipath_egrtidbase; + writel(pa, tidp32); mmiowb(); } @@ -1379,17 +1492,13 @@ static int ipath_pe_early_init(struct ipath_devdata *dd) dd->ipath_egrtidbase = (u64 __iomem *) ((char __iomem *) dd->ipath_kregbase + dd->ipath_rcvegrbase); - /* - * To truly support a 4KB MTU (for usermode), we need to - * bump this to a larger value. For now, we use them for - * the kernel only. - */ - dd->ipath_rcvegrbufsize = 2048; + dd->ipath_rcvegrbufsize = ipath_mtu4096 ? 4096 : 2048; /* * the min() check here is currently a nop, but it may not always * be, depending on just how we do ipath_rcvegrbufsize */ - dd->ipath_ibmaxlen = min(dd->ipath_piosize2k, + dd->ipath_ibmaxlen = min(ipath_mtu4096 ? dd->ipath_piosize4k : + dd->ipath_piosize2k, dd->ipath_rcvegrbufsize + (dd->ipath_rcvhdrentsize << 2)); dd->ipath_init_ibmaxlen = dd->ipath_ibmaxlen; |