diff options
Diffstat (limited to 'drivers/infiniband/hw/ipath/ipath_iba7220.c')
| -rw-r--r-- | drivers/infiniband/hw/ipath/ipath_iba7220.c | 2566 |
1 files changed, 2566 insertions, 0 deletions
diff --git a/drivers/infiniband/hw/ipath/ipath_iba7220.c b/drivers/infiniband/hw/ipath/ipath_iba7220.c new file mode 100644 index 00000000000..e3ec0d1bdf5 --- /dev/null +++ b/drivers/infiniband/hw/ipath/ipath_iba7220.c @@ -0,0 +1,2566 @@ +/* + * Copyright (c) 2006, 2007, 2008 QLogic Corporation. All rights reserved. + * Copyright (c) 2003, 2004, 2005, 2006 PathScale, Inc. All rights reserved. + * + * This software is available to you under a choice of one of two + * licenses. You may choose to be licensed under the terms of the GNU + * General Public License (GPL) Version 2, available from the file + * COPYING in the main directory of this source tree, or the + * OpenIB.org BSD license below: + * + * Redistribution and use in source and binary forms, with or + * without modification, are permitted provided that the following + * conditions are met: + * + * - Redistributions of source code must retain the above + * copyright notice, this list of conditions and the following + * disclaimer. + * + * - Redistributions in binary form must reproduce the above + * copyright notice, this list of conditions and the following + * disclaimer in the documentation and/or other materials + * provided with the distribution. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF + * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS + * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN + * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN + * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE + * SOFTWARE. + */ +/* + * This file contains all of the code that is specific to the + * InfiniPath 7220 chip (except that specific to the SerDes) + */ + +#include <linux/interrupt.h> +#include <linux/pci.h> +#include <linux/delay.h> +#include <linux/io.h> +#include <rdma/ib_verbs.h> + +#include "ipath_kernel.h" +#include "ipath_registers.h" +#include "ipath_7220.h" + +static void ipath_setup_7220_setextled(struct ipath_devdata *, u64, u64); + +static unsigned ipath_compat_ddr_negotiate = 1; + +module_param_named(compat_ddr_negotiate, ipath_compat_ddr_negotiate, uint, + S_IWUSR | S_IRUGO); +MODULE_PARM_DESC(compat_ddr_negotiate, + "Attempt pre-IBTA 1.2 DDR speed negotiation"); + +static unsigned ipath_sdma_fetch_arb = 1; +module_param_named(fetch_arb, ipath_sdma_fetch_arb, uint, S_IRUGO); +MODULE_PARM_DESC(fetch_arb, "IBA7220: change SDMA descriptor arbitration"); + +/* + * This file contains almost all the chip-specific register information and + * access functions for the QLogic InfiniPath 7220 PCI-Express chip, with the + * exception of SerDes support, which in in ipath_sd7220.c. + * + * This lists the InfiniPath registers, in the actual chip layout. + * This structure should never be directly accessed. + */ +struct _infinipath_do_not_use_kernel_regs { + unsigned long long Revision; + unsigned long long Control; + unsigned long long PageAlign; + unsigned long long PortCnt; + unsigned long long DebugPortSelect; + unsigned long long DebugSigsIntSel; /* was Reserved0;*/ + unsigned long long SendRegBase; + unsigned long long UserRegBase; + unsigned long long CounterRegBase; + unsigned long long Scratch; + unsigned long long EEPROMAddrCmd; /* was Reserved1; */ + unsigned long long EEPROMData; /* was Reserved2; */ + unsigned long long IntBlocked; + unsigned long long IntMask; + unsigned long long IntStatus; + unsigned long long IntClear; + unsigned long long ErrorMask; + unsigned long long ErrorStatus; + unsigned long long ErrorClear; + unsigned long long HwErrMask; + unsigned long long HwErrStatus; + unsigned long long HwErrClear; + unsigned long long HwDiagCtrl; + unsigned long long MDIO; + unsigned long long IBCStatus; + unsigned long long IBCCtrl; + unsigned long long ExtStatus; + unsigned long long ExtCtrl; + unsigned long long GPIOOut; + unsigned long long GPIOMask; + unsigned long long GPIOStatus; + unsigned long long GPIOClear; + unsigned long long RcvCtrl; + unsigned long long RcvBTHQP; + unsigned long long RcvHdrSize; + unsigned long long RcvHdrCnt; + unsigned long long RcvHdrEntSize; + unsigned long long RcvTIDBase; + unsigned long long RcvTIDCnt; + unsigned long long RcvEgrBase; + unsigned long long RcvEgrCnt; + unsigned long long RcvBufBase; + unsigned long long RcvBufSize; + unsigned long long RxIntMemBase; + unsigned long long RxIntMemSize; + unsigned long long RcvPartitionKey; + unsigned long long RcvQPMulticastPort; + unsigned long long RcvPktLEDCnt; + unsigned long long IBCDDRCtrl; + unsigned long long HRTBT_GUID; + unsigned long long IB_SDTEST_IF_TX; + unsigned long long IB_SDTEST_IF_RX; + unsigned long long IBCDDRCtrl2; + unsigned long long IBCDDRStatus; + unsigned long long JIntReload; + unsigned long long IBNCModeCtrl; + unsigned long long SendCtrl; + unsigned long long SendBufBase; + unsigned long long SendBufSize; + unsigned long long SendBufCnt; + unsigned long long SendAvailAddr; + unsigned long long TxIntMemBase; + unsigned long long TxIntMemSize; + unsigned long long SendDmaBase; + unsigned long long SendDmaLenGen; + unsigned long long SendDmaTail; + unsigned long long SendDmaHead; + unsigned long long SendDmaHeadAddr; + unsigned long long SendDmaBufMask0; + unsigned long long SendDmaBufMask1; + unsigned long long SendDmaBufMask2; + unsigned long long SendDmaStatus; + unsigned long long SendBufferError; + unsigned long long SendBufferErrorCONT1; + unsigned long long SendBufErr2; /* was Reserved6SBE[0/6] */ + unsigned long long Reserved6L[2]; + unsigned long long AvailUpdCount; + unsigned long long RcvHdrAddr0; + unsigned long long RcvHdrAddrs[16]; /* Why enumerate? */ + unsigned long long Reserved7hdtl; /* Align next to 300 */ + unsigned long long RcvHdrTailAddr0; /* 300, like others */ + unsigned long long RcvHdrTailAddrs[16]; + unsigned long long Reserved9SW[7]; /* was [8]; we have 17 ports */ + unsigned long long IbsdEpbAccCtl; /* IB Serdes EPB access control */ + unsigned long long IbsdEpbTransReg; /* IB Serdes EPB Transaction */ + unsigned long long Reserved10sds; /* was SerdesStatus on */ + unsigned long long XGXSConfig; + unsigned long long IBSerDesCtrl; /* Was IBPLLCfg on Monty */ + unsigned long long EEPCtlStat; /* for "boot" EEPROM/FLASH */ + unsigned long long EEPAddrCmd; + unsigned long long EEPData; + unsigned long long PcieEpbAccCtl; + unsigned long long PcieEpbTransCtl; + unsigned long long EfuseCtl; /* E-Fuse control */ + unsigned long long EfuseData[4]; + unsigned long long ProcMon; + /* this chip moves following two from previous 200, 208 */ + unsigned long long PCIeRBufTestReg0; + unsigned long long PCIeRBufTestReg1; + /* added for this chip */ + unsigned long long PCIeRBufTestReg2; + unsigned long long PCIeRBufTestReg3; + /* added for this chip, debug only */ + unsigned long long SPC_JTAG_ACCESS_REG; + unsigned long long LAControlReg; + unsigned long long GPIODebugSelReg; + unsigned long long DebugPortValueReg; + /* added for this chip, DMA */ + unsigned long long SendDmaBufUsed[3]; + unsigned long long SendDmaReqTagUsed; + /* + * added for this chip, EFUSE: note that these program 64-bit + * words 2 and 3 */ + unsigned long long efuse_pgm_data[2]; + unsigned long long Reserved11LAalign[10]; /* Skip 4B0..4F8 */ + /* we have 30 regs for DDS and RXEQ in IB SERDES */ + unsigned long long SerDesDDSRXEQ[30]; + unsigned long long Reserved12LAalign[2]; /* Skip 5F0, 5F8 */ + /* added for LA debug support */ + unsigned long long LAMemory[32]; +}; + +struct _infinipath_do_not_use_counters { + __u64 LBIntCnt; + __u64 LBFlowStallCnt; + __u64 TxSDmaDescCnt; /* was Reserved1 */ + __u64 TxUnsupVLErrCnt; + __u64 TxDataPktCnt; + __u64 TxFlowPktCnt; + __u64 TxDwordCnt; + __u64 TxLenErrCnt; + __u64 TxMaxMinLenErrCnt; + __u64 TxUnderrunCnt; + __u64 TxFlowStallCnt; + __u64 TxDroppedPktCnt; + __u64 RxDroppedPktCnt; + __u64 RxDataPktCnt; + __u64 RxFlowPktCnt; + __u64 RxDwordCnt; + __u64 RxLenErrCnt; + __u64 RxMaxMinLenErrCnt; + __u64 RxICRCErrCnt; + __u64 RxVCRCErrCnt; + __u64 RxFlowCtrlErrCnt; + __u64 RxBadFormatCnt; + __u64 RxLinkProblemCnt; + __u64 RxEBPCnt; + __u64 RxLPCRCErrCnt; + __u64 RxBufOvflCnt; + __u64 RxTIDFullErrCnt; + __u64 RxTIDValidErrCnt; + __u64 RxPKeyMismatchCnt; + __u64 RxP0HdrEgrOvflCnt; + __u64 RxP1HdrEgrOvflCnt; + __u64 RxP2HdrEgrOvflCnt; + __u64 RxP3HdrEgrOvflCnt; + __u64 RxP4HdrEgrOvflCnt; + __u64 RxP5HdrEgrOvflCnt; + __u64 RxP6HdrEgrOvflCnt; + __u64 RxP7HdrEgrOvflCnt; + __u64 RxP8HdrEgrOvflCnt; + __u64 RxP9HdrEgrOvflCnt; /* was Reserved6 */ + __u64 RxP10HdrEgrOvflCnt; /* was Reserved7 */ + __u64 RxP11HdrEgrOvflCnt; /* new for IBA7220 */ + __u64 RxP12HdrEgrOvflCnt; /* new for IBA7220 */ + __u64 RxP13HdrEgrOvflCnt; /* new for IBA7220 */ + __u64 RxP14HdrEgrOvflCnt; /* new for IBA7220 */ + __u64 RxP15HdrEgrOvflCnt; /* new for IBA7220 */ + __u64 RxP16HdrEgrOvflCnt; /* new for IBA7220 */ + __u64 IBStatusChangeCnt; + __u64 IBLinkErrRecoveryCnt; + __u64 IBLinkDownedCnt; + __u64 IBSymbolErrCnt; + /* The following are new for IBA7220 */ + __u64 RxVL15DroppedPktCnt; + __u64 RxOtherLocalPhyErrCnt; + __u64 PcieRetryBufDiagQwordCnt; + __u64 ExcessBufferOvflCnt; + __u64 LocalLinkIntegrityErrCnt; + __u64 RxVlErrCnt; + __u64 RxDlidFltrCnt; + __u64 Reserved8[7]; + __u64 PSStat; + __u64 PSStart; + __u64 PSInterval; + __u64 PSRcvDataCount; + __u64 PSRcvPktsCount; + __u64 PSXmitDataCount; + __u64 PSXmitPktsCount; + __u64 PSXmitWaitCount; +}; + +#define IPATH_KREG_OFFSET(field) (offsetof( \ + struct _infinipath_do_not_use_kernel_regs, field) / sizeof(u64)) +#define IPATH_CREG_OFFSET(field) (offsetof( \ + struct _infinipath_do_not_use_counters, field) / sizeof(u64)) + +static const struct ipath_kregs ipath_7220_kregs = { + .kr_control = IPATH_KREG_OFFSET(Control), + .kr_counterregbase = IPATH_KREG_OFFSET(CounterRegBase), + .kr_debugportselect = IPATH_KREG_OFFSET(DebugPortSelect), + .kr_errorclear = IPATH_KREG_OFFSET(ErrorClear), + .kr_errormask = IPATH_KREG_OFFSET(ErrorMask), + .kr_errorstatus = IPATH_KREG_OFFSET(ErrorStatus), + .kr_extctrl = IPATH_KREG_OFFSET(ExtCtrl), + .kr_extstatus = IPATH_KREG_OFFSET(ExtStatus), + .kr_gpio_clear = IPATH_KREG_OFFSET(GPIOClear), + .kr_gpio_mask = IPATH_KREG_OFFSET(GPIOMask), + .kr_gpio_out = IPATH_KREG_OFFSET(GPIOOut), + .kr_gpio_status = IPATH_KREG_OFFSET(GPIOStatus), + .kr_hwdiagctrl = IPATH_KREG_OFFSET(HwDiagCtrl), + .kr_hwerrclear = IPATH_KREG_OFFSET(HwErrClear), + .kr_hwerrmask = IPATH_KREG_OFFSET(HwErrMask), + .kr_hwerrstatus = IPATH_KREG_OFFSET(HwErrStatus), + .kr_ibcctrl = IPATH_KREG_OFFSET(IBCCtrl), + .kr_ibcstatus = IPATH_KREG_OFFSET(IBCStatus), + .kr_intblocked = IPATH_KREG_OFFSET(IntBlocked), + .kr_intclear = IPATH_KREG_OFFSET(IntClear), + .kr_intmask = IPATH_KREG_OFFSET(IntMask), + .kr_intstatus = IPATH_KREG_OFFSET(IntStatus), + .kr_mdio = IPATH_KREG_OFFSET(MDIO), + .kr_pagealign = IPATH_KREG_OFFSET(PageAlign), + .kr_partitionkey = IPATH_KREG_OFFSET(RcvPartitionKey), + .kr_portcnt = IPATH_KREG_OFFSET(PortCnt), + .kr_rcvbthqp = IPATH_KREG_OFFSET(RcvBTHQP), + .kr_rcvbufbase = IPATH_KREG_OFFSET(RcvBufBase), + .kr_rcvbufsize = IPATH_KREG_OFFSET(RcvBufSize), + .kr_rcvctrl = IPATH_KREG_OFFSET(RcvCtrl), + .kr_rcvegrbase = IPATH_KREG_OFFSET(RcvEgrBase), + .kr_rcvegrcnt = IPATH_KREG_OFFSET(RcvEgrCnt), + .kr_rcvhdrcnt = IPATH_KREG_OFFSET(RcvHdrCnt), + .kr_rcvhdrentsize = IPATH_KREG_OFFSET(RcvHdrEntSize), + .kr_rcvhdrsize = IPATH_KREG_OFFSET(RcvHdrSize), + .kr_rcvintmembase = IPATH_KREG_OFFSET(RxIntMemBase), + .kr_rcvintmemsize = IPATH_KREG_OFFSET(RxIntMemSize), + .kr_rcvtidbase = IPATH_KREG_OFFSET(RcvTIDBase), + .kr_rcvtidcnt = IPATH_KREG_OFFSET(RcvTIDCnt), + .kr_revision = IPATH_KREG_OFFSET(Revision), + .kr_scratch = IPATH_KREG_OFFSET(Scratch), + .kr_sendbuffererror = IPATH_KREG_OFFSET(SendBufferError), + .kr_sendctrl = IPATH_KREG_OFFSET(SendCtrl), + .kr_sendpioavailaddr = IPATH_KREG_OFFSET(SendAvailAddr), + .kr_sendpiobufbase = IPATH_KREG_OFFSET(SendBufBase), + .kr_sendpiobufcnt = IPATH_KREG_OFFSET(SendBufCnt), + .kr_sendpiosize = IPATH_KREG_OFFSET(SendBufSize), + .kr_sendregbase = IPATH_KREG_OFFSET(SendRegBase), + .kr_txintmembase = IPATH_KREG_OFFSET(TxIntMemBase), + .kr_txintmemsize = IPATH_KREG_OFFSET(TxIntMemSize), + .kr_userregbase = IPATH_KREG_OFFSET(UserRegBase), + + .kr_xgxsconfig = IPATH_KREG_OFFSET(XGXSConfig), + + /* send dma related regs */ + .kr_senddmabase = IPATH_KREG_OFFSET(SendDmaBase), + .kr_senddmalengen = IPATH_KREG_OFFSET(SendDmaLenGen), + .kr_senddmatail = IPATH_KREG_OFFSET(SendDmaTail), + .kr_senddmahead = IPATH_KREG_OFFSET(SendDmaHead), + .kr_senddmaheadaddr = IPATH_KREG_OFFSET(SendDmaHeadAddr), + .kr_senddmabufmask0 = IPATH_KREG_OFFSET(SendDmaBufMask0), + .kr_senddmabufmask1 = IPATH_KREG_OFFSET(SendDmaBufMask1), + .kr_senddmabufmask2 = IPATH_KREG_OFFSET(SendDmaBufMask2), + .kr_senddmastatus = IPATH_KREG_OFFSET(SendDmaStatus), + + /* SerDes related regs */ + .kr_ibserdesctrl = IPATH_KREG_OFFSET(IBSerDesCtrl), + .kr_ib_epbacc = IPATH_KREG_OFFSET(IbsdEpbAccCtl), + .kr_ib_epbtrans = IPATH_KREG_OFFSET(IbsdEpbTransReg), + .kr_pcie_epbacc = IPATH_KREG_OFFSET(PcieEpbAccCtl), + .kr_pcie_epbtrans = IPATH_KREG_OFFSET(PcieEpbTransCtl), + .kr_ib_ddsrxeq = IPATH_KREG_OFFSET(SerDesDDSRXEQ), + + /* + * These should not be used directly via ipath_read_kreg64(), + * use them with ipath_read_kreg64_port() + */ + .kr_rcvhdraddr = IPATH_KREG_OFFSET(RcvHdrAddr0), + .kr_rcvhdrtailaddr = IPATH_KREG_OFFSET(RcvHdrTailAddr0), + + /* + * The rcvpktled register controls one of the debug port signals, so + * a packet activity LED can be connected to it. + */ + .kr_rcvpktledcnt = IPATH_KREG_OFFSET(RcvPktLEDCnt), + .kr_pcierbuftestreg0 = IPATH_KREG_OFFSET(PCIeRBufTestReg0), + .kr_pcierbuftestreg1 = IPATH_KREG_OFFSET(PCIeRBufTestReg1), + + .kr_hrtbt_guid = IPATH_KREG_OFFSET(HRTBT_GUID), + .kr_ibcddrctrl = IPATH_KREG_OFFSET(IBCDDRCtrl), + .kr_ibcddrstatus = IPATH_KREG_OFFSET(IBCDDRStatus), + .kr_jintreload = IPATH_KREG_OFFSET(JIntReload) +}; + +static const struct ipath_cregs ipath_7220_cregs = { + .cr_badformatcnt = IPATH_CREG_OFFSET(RxBadFormatCnt), + .cr_erricrccnt = IPATH_CREG_OFFSET(RxICRCErrCnt), + .cr_errlinkcnt = IPATH_CREG_OFFSET(RxLinkProblemCnt), + .cr_errlpcrccnt = IPATH_CREG_OFFSET(RxLPCRCErrCnt), + .cr_errpkey = IPATH_CREG_OFFSET(RxPKeyMismatchCnt), + .cr_errrcvflowctrlcnt = IPATH_CREG_OFFSET(RxFlowCtrlErrCnt), + .cr_err_rlencnt = IPATH_CREG_OFFSET(RxLenErrCnt), + .cr_errslencnt = IPATH_CREG_OFFSET(TxLenErrCnt), + .cr_errtidfull = IPATH_CREG_OFFSET(RxTIDFullErrCnt), + .cr_errtidvalid = IPATH_CREG_OFFSET(RxTIDValidErrCnt), + .cr_errvcrccnt = IPATH_CREG_OFFSET(RxVCRCErrCnt), + .cr_ibstatuschange = IPATH_CREG_OFFSET(IBStatusChangeCnt), + .cr_intcnt = IPATH_CREG_OFFSET(LBIntCnt), + .cr_invalidrlencnt = IPATH_CREG_OFFSET(RxMaxMinLenErrCnt), + .cr_invalidslencnt = IPATH_CREG_OFFSET(TxMaxMinLenErrCnt), + .cr_lbflowstallcnt = IPATH_CREG_OFFSET(LBFlowStallCnt), + .cr_pktrcvcnt = IPATH_CREG_OFFSET(RxDataPktCnt), + .cr_pktrcvflowctrlcnt = IPATH_CREG_OFFSET(RxFlowPktCnt), + .cr_pktsendcnt = IPATH_CREG_OFFSET(TxDataPktCnt), + .cr_pktsendflowcnt = IPATH_CREG_OFFSET(TxFlowPktCnt), + .cr_portovflcnt = IPATH_CREG_OFFSET(RxP0HdrEgrOvflCnt), + .cr_rcvebpcnt = IPATH_CREG_OFFSET(RxEBPCnt), + .cr_rcvovflcnt = IPATH_CREG_OFFSET(RxBufOvflCnt), + .cr_senddropped = IPATH_CREG_OFFSET(TxDroppedPktCnt), + .cr_sendstallcnt = IPATH_CREG_OFFSET(TxFlowStallCnt), + .cr_sendunderruncnt = IPATH_CREG_OFFSET(TxUnderrunCnt), + .cr_wordrcvcnt = IPATH_CREG_OFFSET(RxDwordCnt), + .cr_wordsendcnt = IPATH_CREG_OFFSET(TxDwordCnt), + .cr_unsupvlcnt = IPATH_CREG_OFFSET(TxUnsupVLErrCnt), + .cr_rxdroppktcnt = IPATH_CREG_OFFSET(RxDroppedPktCnt), + .cr_iblinkerrrecovcnt = IPATH_CREG_OFFSET(IBLinkErrRecoveryCnt), + .cr_iblinkdowncnt = IPATH_CREG_OFFSET(IBLinkDownedCnt), + .cr_ibsymbolerrcnt = IPATH_CREG_OFFSET(IBSymbolErrCnt), + .cr_vl15droppedpktcnt = IPATH_CREG_OFFSET(RxVL15DroppedPktCnt), + .cr_rxotherlocalphyerrcnt = + IPATH_CREG_OFFSET(RxOtherLocalPhyErrCnt), + .cr_excessbufferovflcnt = IPATH_CREG_OFFSET(ExcessBufferOvflCnt), + .cr_locallinkintegrityerrcnt = + IPATH_CREG_OFFSET(LocalLinkIntegrityErrCnt), + .cr_rxvlerrcnt = IPATH_CREG_OFFSET(RxVlErrCnt), + .cr_rxdlidfltrcnt = IPATH_CREG_OFFSET(RxDlidFltrCnt), + .cr_psstat = IPATH_CREG_OFFSET(PSStat), + .cr_psstart = IPATH_CREG_OFFSET(PSStart), + .cr_psinterval = IPATH_CREG_OFFSET(PSInterval), + .cr_psrcvdatacount = IPATH_CREG_OFFSET(PSRcvDataCount), + .cr_psrcvpktscount = IPATH_CREG_OFFSET(PSRcvPktsCount), + .cr_psxmitdatacount = IPATH_CREG_OFFSET(PSXmitDataCount), + .cr_psxmitpktscount = IPATH_CREG_OFFSET(PSXmitPktsCount), + .cr_psxmitwaitcount = IPATH_CREG_OFFSET(PSXmitWaitCount), +}; + +/* kr_control bits */ +#define INFINIPATH_C_RESET (1U<<7) + +/* kr_intstatus, kr_intclear, kr_intmask bits */ +#define INFINIPATH_I_RCVURG_MASK ((1ULL<<17)-1) +#define INFINIPATH_I_RCVURG_SHIFT 32 +#define INFINIPATH_I_RCVAVAIL_MASK ((1ULL<<17)-1) +#define INFINIPATH_I_RCVAVAIL_SHIFT 0 +#define INFINIPATH_I_SERDESTRIMDONE (1ULL<<27) + +/* kr_hwerrclear, kr_hwerrmask, kr_hwerrstatus, bits */ +#define INFINIPATH_HWE_PCIEMEMPARITYERR_MASK 0x00000000000000ffULL +#define INFINIPATH_HWE_PCIEMEMPARITYERR_SHIFT 0 +#define INFINIPATH_HWE_PCIEPOISONEDTLP 0x0000000010000000ULL +#define INFINIPATH_HWE_PCIECPLTIMEOUT 0x0000000020000000ULL +#define INFINIPATH_HWE_PCIEBUSPARITYXTLH 0x0000000040000000ULL +#define INFINIPATH_HWE_PCIEBUSPARITYXADM 0x0000000080000000ULL +#define INFINIPATH_HWE_PCIEBUSPARITYRADM 0x0000000100000000ULL +#define INFINIPATH_HWE_COREPLL_FBSLIP 0x0080000000000000ULL +#define INFINIPATH_HWE_COREPLL_RFSLIP 0x0100000000000000ULL +#define INFINIPATH_HWE_PCIE1PLLFAILED 0x0400000000000000ULL +#define INFINIPATH_HWE_PCIE0PLLFAILED 0x0800000000000000ULL +#define INFINIPATH_HWE_SERDESPLLFAILED 0x1000000000000000ULL +/* specific to this chip */ +#define INFINIPATH_HWE_PCIECPLDATAQUEUEERR 0x0000000000000040ULL +#define INFINIPATH_HWE_PCIECPLHDRQUEUEERR 0x0000000000000080ULL +#define INFINIPATH_HWE_SDMAMEMREADERR 0x0000000010000000ULL +#define INFINIPATH_HWE_CLK_UC_PLLNOTLOCKED 0x2000000000000000ULL +#define INFINIPATH_HWE_PCIESERDESQ0PCLKNOTDETECT 0x0100000000000000ULL +#define INFINIPATH_HWE_PCIESERDESQ1PCLKNOTDETECT 0x0200000000000000ULL +#define INFINIPATH_HWE_PCIESERDESQ2PCLKNOTDETECT 0x0400000000000000ULL +#define INFINIPATH_HWE_PCIESERDESQ3PCLKNOTDETECT 0x0800000000000000ULL +#define INFINIPATH_HWE_DDSRXEQMEMORYPARITYERR 0x0000008000000000ULL +#define INFINIPATH_HWE_IB_UC_MEMORYPARITYERR 0x0000004000000000ULL +#define INFINIPATH_HWE_PCIE_UC_OCT0MEMORYPARITYERR 0x0000001000000000ULL +#define INFINIPATH_HWE_PCIE_UC_OCT1MEMORYPARITYERR 0x0000002000000000ULL + +#define IBA7220_IBCS_LINKTRAININGSTATE_MASK 0x1F +#define IBA7220_IBCS_LINKSTATE_SHIFT 5 +#define IBA7220_IBCS_LINKSPEED_SHIFT 8 +#define IBA7220_IBCS_LINKWIDTH_SHIFT 9 + +#define IBA7220_IBCC_LINKINITCMD_MASK 0x7ULL +#define IBA7220_IBCC_LINKCMD_SHIFT 19 +#define IBA7220_IBCC_MAXPKTLEN_SHIFT 21 + +/* kr_ibcddrctrl bits */ +#define IBA7220_IBC_DLIDLMC_MASK 0xFFFFFFFFUL +#define IBA7220_IBC_DLIDLMC_SHIFT 32 +#define IBA7220_IBC_HRTBT_MASK 3 +#define IBA7220_IBC_HRTBT_SHIFT 16 +#define IBA7220_IBC_HRTBT_ENB 0x10000UL +#define IBA7220_IBC_LANE_REV_SUPPORTED (1<<8) +#define IBA7220_IBC_LREV_MASK 1 +#define IBA7220_IBC_LREV_SHIFT 8 +#define IBA7220_IBC_RXPOL_MASK 1 +#define IBA7220_IBC_RXPOL_SHIFT 7 +#define IBA7220_IBC_WIDTH_SHIFT 5 +#define IBA7220_IBC_WIDTH_MASK 0x3 +#define IBA7220_IBC_WIDTH_1X_ONLY (0<<IBA7220_IBC_WIDTH_SHIFT) +#define IBA7220_IBC_WIDTH_4X_ONLY (1<<IBA7220_IBC_WIDTH_SHIFT) +#define IBA7220_IBC_WIDTH_AUTONEG (2<<IBA7220_IBC_WIDTH_SHIFT) +#define IBA7220_IBC_SPEED_AUTONEG (1<<1) +#define IBA7220_IBC_SPEED_SDR (1<<2) +#define IBA7220_IBC_SPEED_DDR (1<<3) +#define IBA7220_IBC_SPEED_AUTONEG_MASK (0x7<<1) +#define IBA7220_IBC_IBTA_1_2_MASK (1) + +/* kr_ibcddrstatus */ +/* link latency shift is 0, don't bother defining */ +#define IBA7220_DDRSTAT_LINKLAT_MASK 0x3ffffff + +/* kr_extstatus bits */ +#define INFINIPATH_EXTS_FREQSEL 0x2 +#define INFINIPATH_EXTS_SERDESSEL 0x4 +#define INFINIPATH_EXTS_MEMBIST_ENDTEST 0x0000000000004000 +#define INFINIPATH_EXTS_MEMBIST_DISABLED 0x0000000000008000 + +/* kr_xgxsconfig bits */ +#define INFINIPATH_XGXS_RESET 0x5ULL +#define INFINIPATH_XGXS_FC_SAFE (1ULL<<63) + +/* kr_rcvpktledcnt */ +#define IBA7220_LEDBLINK_ON_SHIFT 32 /* 4ns period on after packet */ +#define IBA7220_LEDBLINK_OFF_SHIFT 0 /* 4ns period off before next on */ + +#define _IPATH_GPIO_SDA_NUM 1 +#define _IPATH_GPIO_SCL_NUM 0 + +#define IPATH_GPIO_SDA (1ULL << \ + (_IPATH_GPIO_SDA_NUM+INFINIPATH_EXTC_GPIOOE_SHIFT)) +#define IPATH_GPIO_SCL (1ULL << \ + (_IPATH_GPIO_SCL_NUM+INFINIPATH_EXTC_GPIOOE_SHIFT)) + +#define IBA7220_R_INTRAVAIL_SHIFT 17 +#define IBA7220_R_TAILUPD_SHIFT 35 +#define IBA7220_R_PORTCFG_SHIFT 36 + +#define INFINIPATH_JINT_PACKETSHIFT 16 +#define INFINIPATH_JINT_DEFAULT_IDLE_TICKS 0 +#define INFINIPATH_JINT_DEFAULT_MAX_PACKETS 0 + +#define IBA7220_HDRHEAD_PKTINT_SHIFT 32 /* interrupt cnt in upper 32 bits */ + +/* + * the size bits give us 2^N, in KB units. 0 marks as invalid, + * and 7 is reserved. We currently use only 2KB and 4KB + */ +#define IBA7220_TID_SZ_SHIFT 37 /* shift to 3bit size selector */ +#define IBA7220_TID_SZ_2K (1UL<<IBA7220_TID_SZ_SHIFT) /* 2KB */ +#define IBA7220_TID_SZ_4K (2UL<<IBA7220_TID_SZ_SHIFT) /* 4KB */ +#define IBA7220_TID_PA_SHIFT 11U /* TID addr in chip stored w/o low bits */ + +#define IPATH_AUTONEG_TRIES 5 /* sequential retries to negotiate DDR */ + +static char int_type[16] = "auto"; +module_param_string(interrupt_type, int_type, sizeof(int_type), 0444); +MODULE_PARM_DESC(int_type, " interrupt_type=auto|force_msi|force_intx\n"); + +/* packet rate matching delay; chip has support */ +static u8 rate_to_delay[2][2] = { + /* 1x, 4x */ + { 8, 2 }, /* SDR */ + { 4, 1 } /* DDR */ +}; + +/* 7220 specific hardware errors... */ +static const struct ipath_hwerror_msgs ipath_7220_hwerror_msgs[] = { + INFINIPATH_HWE_MSG(PCIEPOISONEDTLP, "PCIe Poisoned TLP"), + INFINIPATH_HWE_MSG(PCIECPLTIMEOUT, "PCIe completion timeout"), + /* + * In practice, it's unlikely wthat we'll see PCIe PLL, or bus + * parity or memory parity error failures, because most likely we + * won't be able to talk to the core of the chip. Nonetheless, we + * might see them, if they are in parts of the PCIe core that aren't + * essential. + */ + INFINIPATH_HWE_MSG(PCIE1PLLFAILED, "PCIePLL1"), + INFINIPATH_HWE_MSG(PCIE0PLLFAILED, "PCIePLL0"), + INFINIPATH_HWE_MSG(PCIEBUSPARITYXTLH, "PCIe XTLH core parity"), + INFINIPATH_HWE_MSG(PCIEBUSPARITYXADM, "PCIe ADM TX core parity"), + INFINIPATH_HWE_MSG(PCIEBUSPARITYRADM, "PCIe ADM RX core parity"), + INFINIPATH_HWE_MSG(RXDSYNCMEMPARITYERR, "Rx Dsync"), + INFINIPATH_HWE_MSG(SERDESPLLFAILED, "SerDes PLL"), + INFINIPATH_HWE_MSG(PCIECPLDATAQUEUEERR, "PCIe cpl header queue"), + INFINIPATH_HWE_MSG(PCIECPLHDRQUEUEERR, "PCIe cpl data queue"), + INFINIPATH_HWE_MSG(SDMAMEMREADERR, "Send DMA memory read"), + INFINIPATH_HWE_MSG(CLK_UC_PLLNOTLOCKED, "uC PLL clock not locked"), + INFINIPATH_HWE_MSG(PCIESERDESQ0PCLKNOTDETECT, + "PCIe serdes Q0 no clock"), + INFINIPATH_HWE_MSG(PCIESERDESQ1PCLKNOTDETECT, + "PCIe serdes Q1 no clock"), + INFINIPATH_HWE_MSG(PCIESERDESQ2PCLKNOTDETECT, + "PCIe serdes Q2 no clock"), + INFINIPATH_HWE_MSG(PCIESERDESQ3PCLKNOTDETECT, + "PCIe serdes Q3 no clock"), + INFINIPATH_HWE_MSG(DDSRXEQMEMORYPARITYERR, + "DDS RXEQ memory parity"), + INFINIPATH_HWE_MSG(IB_UC_MEMORYPARITYERR, "IB uC memory parity"), + INFINIPATH_HWE_MSG(PCIE_UC_OCT0MEMORYPARITYERR, + "PCIe uC oct0 memory parity"), + INFINIPATH_HWE_MSG(PCIE_UC_OCT1MEMORYPARITYERR, + "PCIe uC oct1 memory parity"), +}; + +static void autoneg_work(struct work_struct *); + +/* + * the offset is different for different configured port numbers, since + * port0 is fixed in size, but others can vary. Make it a function to + * make the issue more obvious. +*/ +static inline u32 port_egrtid_idx(struct ipath_devdata *dd, unsigned port) +{ + return port ? dd->ipath_p0_rcvegrcnt + + (port-1) * dd->ipath_rcvegrcnt : 0; +} + +static void ipath_7220_txe_recover(struct ipath_devdata *dd) +{ + ++ipath_stats.sps_txeparity; + + dev_info(&dd->pcidev->dev, + "Recovering from TXE PIO parity error\n"); + ipath_disarm_senderrbufs(dd, 1); +} + + +/** + * ipath_7220_handle_hwerrors - display hardware errors. + * @dd: the infinipath device + * @msg: the output buffer + * @msgl: the size of the output buffer + * + * Use same msg buffer as regular errors to avoid excessive stack + * use. Most hardware errors are catastrophic, but for right now, + * we'll print them and continue. We reuse the same message buffer as + * ipath_handle_errors() to avoid excessive stack usage. + */ +static void ipath_7220_handle_hwerrors(struct ipath_devdata *dd, char *msg, + size_t msgl) +{ + ipath_err_t hwerrs; + u32 bits, ctrl; + int isfatal = 0; + char bitsmsg[64]; + int log_idx; + + hwerrs = ipath_read_kreg64(dd, dd->ipath_kregs->kr_hwerrstatus); + if (!hwerrs) { + /* + * better than printing cofusing messages + * This seems to be related to clearing the crc error, or + * the pll error during init. + */ + ipath_cdbg(VERBOSE, "Called but no hardware errors set\n"); + goto bail; + } else if (hwerrs == ~0ULL) { + ipath_dev_err(dd, "Read of hardware error status failed " + "(all bits set); ignoring\n"); + goto bail; + } + ipath_stats.sps_hwerrs++; + + /* + * Always clear the error status register, except MEMBISTFAIL, + * regardless of whether we continue or stop using the chip. + * We want that set so we know it failed, even across driver reload. + * We'll still ignore it in the hwerrmask. We do this partly for + * diagnostics, but also for support. + */ + ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrclear, + hwerrs&~INFINIPATH_HWE_MEMBISTFAILED); + + hwerrs &= dd->ipath_hwerrmask; + + /* We log some errors to EEPROM, check if we have any of those. */ + for (log_idx = 0; log_idx < IPATH_EEP_LOG_CNT; ++log_idx) + if (hwerrs & dd->ipath_eep_st_masks[log_idx].hwerrs_to_log) + ipath_inc_eeprom_err(dd, log_idx, 1); + /* + * Make sure we get this much out, unless told to be quiet, + * or it's occurred within the last 5 seconds. + */ + if ((hwerrs & ~(dd->ipath_lasthwerror | + ((INFINIPATH_HWE_TXEMEMPARITYERR_PIOBUF | + INFINIPATH_HWE_TXEMEMPARITYERR_PIOPBC) + << INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT))) || + (ipath_debug & __IPATH_VERBDBG)) + dev_info(&dd->pcidev->dev, "Hardware error: hwerr=0x%llx " + "(cleared)\n", (unsigned long long) hwerrs); + dd->ipath_lasthwerror |= hwerrs; + + if (hwerrs & ~dd->ipath_hwe_bitsextant) + ipath_dev_err(dd, "hwerror interrupt with unknown errors " + "%llx set\n", (unsigned long long) + (hwerrs & ~dd->ipath_hwe_bitsextant)); + + if (hwerrs & INFINIPATH_HWE_IB_UC_MEMORYPARITYERR) + ipath_sd7220_clr_ibpar(dd); + + ctrl = ipath_read_kreg32(dd, dd->ipath_kregs->kr_control); + if ((ctrl & INFINIPATH_C_FREEZEMODE) && !ipath_diag_inuse) { + /* + * Parity errors in send memory are recoverable, + * just cancel the send (if indicated in * sendbuffererror), + * count the occurrence, unfreeze (if no other handled + * hardware error bits are set), and continue. + */ + if (hwerrs & ((INFINIPATH_HWE_TXEMEMPARITYERR_PIOBUF | + INFINIPATH_HWE_TXEMEMPARITYERR_PIOPBC) + << INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT)) { + ipath_7220_txe_recover(dd); + hwerrs &= ~((INFINIPATH_HWE_TXEMEMPARITYERR_PIOBUF | + INFINIPATH_HWE_TXEMEMPARITYERR_PIOPBC) + << INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT); + if (!hwerrs) { + /* else leave in freeze mode */ + ipath_write_kreg(dd, + dd->ipath_kregs->kr_control, + dd->ipath_control); + goto bail; + } + } + if (hwerrs) { + /* + * If any set that we aren't ignoring only make the + * complaint once, in case it's stuck or recurring, + * and we get here multiple times + * Force link down, so switch knows, and + * LEDs are turned off. + */ + if (dd->ipath_flags & IPATH_INITTED) { + ipath_set_linkstate(dd, IPATH_IB_LINKDOWN); + ipath_setup_7220_setextled(dd, + INFINIPATH_IBCS_L_STATE_DOWN, + INFINIPATH_IBCS_LT_STATE_DISABLED); + ipath_dev_err(dd, "Fatal Hardware Error " + "(freeze mode), no longer" + " usable, SN %.16s\n", + dd->ipath_serial); + isfatal = 1; + } + /* + * Mark as having had an error for driver, and also + * for /sys and status word mapped to user programs. + * This marks unit as not usable, until reset. + */ + *dd->ipath_statusp &= ~IPATH_STATUS_IB_READY; + *dd->ipath_statusp |= IPATH_STATUS_HWERROR; + dd->ipath_flags &= ~IPATH_INITTED; + } else { + ipath_dbg("Clearing freezemode on ignored hardware " + "error\n"); + ipath_clear_freeze(dd); + } + } + + *msg = '\0'; + + if (hwerrs & INFINIPATH_HWE_MEMBISTFAILED) { + strlcat(msg, "[Memory BIST test failed, " + "InfiniPath hardware unusable]", msgl); + /* ignore from now on, so disable until driver reloaded */ + *dd->ipath_statusp |= IPATH_STATUS_HWERROR; + dd->ipath_hwerrmask &= ~INFINIPATH_HWE_MEMBISTFAILED; + ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrmask, + dd->ipath_hwerrmask); + } + + ipath_format_hwerrors(hwerrs, + ipath_7220_hwerror_msgs, + ARRAY_SIZE(ipath_7220_hwerror_msgs), + msg, msgl); + + if (hwerrs & (INFINIPATH_HWE_PCIEMEMPARITYERR_MASK + << INFINIPATH_HWE_PCIEMEMPARITYERR_SHIFT)) { + bits = (u32) ((hwerrs >> + INFINIPATH_HWE_PCIEMEMPARITYERR_SHIFT) & + INFINIPATH_HWE_PCIEMEMPARITYERR_MASK); + snprintf(bitsmsg, sizeof bitsmsg, + "[PCIe Mem Parity Errs %x] ", bits); + strlcat(msg, bitsmsg, msgl); + } + +#define _IPATH_PLL_FAIL (INFINIPATH_HWE_COREPLL_FBSLIP | \ + INFINIPATH_HWE_COREPLL_RFSLIP) + + if (hwerrs & _IPATH_PLL_FAIL) { + snprintf(bitsmsg, sizeof bitsmsg, + "[PLL failed (%llx), InfiniPath hardware unusable]", + (unsigned long long) hwerrs & _IPATH_PLL_FAIL); + strlcat(msg, bitsmsg, msgl); + /* ignore from now on, so disable until driver reloaded */ + dd->ipath_hwerrmask &= ~(hwerrs & _IPATH_PLL_FAIL); + ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrmask, + dd->ipath_hwerrmask); + } + + if (hwerrs & INFINIPATH_HWE_SERDESPLLFAILED) { + /* + * If it occurs, it is left masked since the eternal + * interface is unused. + */ + dd->ipath_hwerrmask &= ~INFINIPATH_HWE_SERDESPLLFAILED; + ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrmask, + dd->ipath_hwerrmask); + } + + ipath_dev_err(dd, "%s hardware error\n", msg); + /* + * For /sys status file. if no trailing } is copied, we'll + * know it was truncated. + */ + if (isfatal && !ipath_diag_inuse && dd->ipath_freezemsg) + snprintf(dd->ipath_freezemsg, dd->ipath_freezelen, + "{%s}", msg); +bail:; +} + +/** + * ipath_7220_boardname - fill in the board name + * @dd: the infinipath device + * @name: the output buffer + * @namelen: the size of the output buffer + * + * info is based on the board revision register + */ +static int ipath_7220_boardname(struct ipath_devdata *dd, char *name, + size_t namelen) +{ + char *n = NULL; + u8 boardrev = dd->ipath_boardrev; + int ret; + + if (boardrev == 15) { + /* + * Emulator sometimes comes up all-ones, rather than zero. + */ + boardrev = 0; + dd->ipath_boardrev = boardrev; + } + switch (boardrev) { + case 0: + n = "InfiniPath_7220_Emulation"; + break; + case 1: + n = "InfiniPath_QLE7240"; + break; + case 2: + n = "InfiniPath_QLE7280"; + break; + case 3: + n = "InfiniPath_QLE7242"; + break; + case 4: + n = "InfiniPath_QEM7240"; + break; + case 5: + n = "InfiniPath_QMI7240"; + break; + case 6: + n = "InfiniPath_QMI7264"; + break; + case 7: + n = "InfiniPath_QMH7240"; + break; + case 8: + n = "InfiniPath_QME7240"; + break; + case 9: + n = "InfiniPath_QLE7250"; + break; + case 10: + n = "InfiniPath_QLE7290"; + break; + case 11: + n = "InfiniPath_QEM7250"; + break; + case 12: + n = "InfiniPath_QLE-Bringup"; + break; + default: + ipath_dev_err(dd, + "Don't yet know about board with ID %u\n", + boardrev); + snprintf(name, namelen, "Unknown_InfiniPath_PCIe_%u", + boardrev); + break; + } + if (n) + snprintf(name, namelen, "%s", n); + + if (dd->ipath_majrev != 5 || !dd->ipath_minrev || + dd->ipath_minrev > 2) { + ipath_dev_err(dd, "Unsupported InfiniPath hardware " + "revision %u.%u!\n", + dd->ipath_majrev, dd->ipath_minrev); + ret = 1; + } else if (dd->ipath_minrev == 1) { + /* Rev1 chips are prototype. Complain, but allow use */ + ipath_dev_err(dd, "Unsupported hardware " + "revision %u.%u, Contact support@qlogic.com\n", + dd->ipath_majrev, dd->ipath_minrev); + ret = 0; + } else + ret = 0; + + /* + * Set here not in ipath_init_*_funcs because we have to do + * it after we can read chip registers. + */ + dd->ipath_ureg_align = 0x10000; /* 64KB alignment */ + + return ret; +} + +/** + * ipath_7220_init_hwerrors - enable hardware errors + * @dd: the infinipath device + * + * now that we have finished initializing everything that might reasonably + * cause a hardware error, and cleared those errors bits as they occur, + * we can enable hardware errors in the mask (potentially enabling + * freeze mode), and enable hardware errors as errors (along with + * everything else) in errormask + */ +static void ipath_7220_init_hwerrors(struct ipath_devdata *dd) +{ + ipath_err_t val; + u64 extsval; + + extsval = ipath_read_kreg64(dd, dd->ipath_kregs->kr_extstatus); + + if (!(extsval & (INFINIPATH_EXTS_MEMBIST_ENDTEST | + INFINIPATH_EXTS_MEMBIST_DISABLED))) + ipath_dev_err(dd, "MemBIST did not complete!\n"); + if (extsval & INFINIPATH_EXTS_MEMBIST_DISABLED) + dev_info(&dd->pcidev->dev, "MemBIST is disabled.\n"); + + val = ~0ULL; /* barring bugs, all hwerrors become interrupts, */ + + if (!dd->ipath_boardrev) /* no PLL for Emulator */ + val &= ~INFINIPATH_HWE_SERDESPLLFAILED; + + if (dd->ipath_minrev == 1) + val &= ~(1ULL << 42); /* TXE LaunchFIFO Parity rev1 issue */ + + val &= ~INFINIPATH_HWE_IB_UC_MEMORYPARITYERR; + dd->ipath_hwerrmask = val; + + /* + * special trigger "error" is for debugging purposes. It + * works around a processor/chipset problem. The error + * interrupt allows us to count occurrences, but we don't + * want to pay the overhead for normal use. Emulation only + */ + if (!dd->ipath_boardrev) + dd->ipath_maskederrs = INFINIPATH_E_SENDSPECIALTRIGGER; +} + +/* + * All detailed interaction with the SerDes has been moved to ipath_sd7220.c + * + * The portion of IBA7220-specific bringup_serdes() that actually deals with + * registers and memory within the SerDes itself is ipath_sd7220_init(). + */ + +/** + * ipath_7220_bringup_serdes - bring up the serdes + * @dd: the infinipath device + */ +static int ipath_7220_bringup_serdes(struct ipath_devdata *dd) +{ + int ret = 0; + u64 val, prev_val, guid; + int was_reset; /* Note whether uC was reset */ + + ipath_dbg("Trying to bringup serdes\n"); + + if (ipath_read_kreg64(dd, dd->ipath_kregs->kr_hwerrstatus) & + INFINIPATH_HWE_SERDESPLLFAILED) { + ipath_dbg("At start, serdes PLL failed bit set " + "in hwerrstatus, clearing and continuing\n"); + ipath_write_kreg(dd, dd->ipath_kregs->kr_hwerrclear, + INFINIPATH_HWE_SERDESPLLFAILED); + } + + if (!dd->ipath_ibcddrctrl) { + /* not on re-init after reset */ + dd->ipath_ibcddrctrl = + ipath_read_kreg64(dd, dd->ipath_kregs->kr_ibcddrctrl); + + if (dd->ipath_link_speed_enabled == + (IPATH_IB_SDR | IPATH_IB_DDR)) + dd->ipath_ibcddrctrl |= + IBA7220_IBC_SPEED_AUTONEG_MASK | + IBA7220_IBC_IBTA_1_2_MASK; + else + dd->ipath_ibcddrctrl |= + dd->ipath_link_speed_enabled == IPATH_IB_DDR + ? IBA7220_IBC_SPEED_DDR : + IBA7220_IBC_SPEED_SDR; + if ((dd->ipath_link_width_enabled & (IB_WIDTH_1X | + IB_WIDTH_4X)) == (IB_WIDTH_1X | IB_WIDTH_4X)) + dd->ipath_ibcddrctrl |= IBA7220_IBC_WIDTH_AUTONEG; + else + dd->ipath_ibcddrctrl |= + dd->ipath_link_width_enabled == IB_WIDTH_4X + ? IBA7220_IBC_WIDTH_4X_ONLY : + IBA7220_IBC_WIDTH_1X_ONLY; + + /* always enable these on driver reload, not sticky */ + dd->ipath_ibcddrctrl |= + IBA7220_IBC_RXPOL_MASK << IBA7220_IBC_RXPOL_SHIFT; + dd->ipath_ibcddrctrl |= + IBA7220_IBC_HRTBT_MASK << IBA7220_IBC_HRTBT_SHIFT; + /* + * automatic lane reversal detection for receive + * doesn't work correctly in rev 1, so disable it + * on that rev, otherwise enable (disabling not + * sticky across reload for >rev1) + */ + if (dd->ipath_minrev == 1) + dd->ipath_ibcddrctrl &= + ~IBA7220_IBC_LANE_REV_SUPPORTED; + else + dd->ipath_ibcddrctrl |= + IBA7220_IBC_LANE_REV_SUPPORTED; + } + + ipath_write_kreg(dd, dd->ipath_kregs->kr_ibcddrctrl, + dd->ipath_ibcddrctrl); + + ipath_write_kreg(dd, IPATH_KREG_OFFSET(IBNCModeCtrl), 0Ull); + + /* IBA7220 has SERDES MPU reset in D0 of what _was_ IBPLLCfg */ + val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_ibserdesctrl); + /* remember if uC was in Reset or not, for dactrim */ + was_reset = (val & 1); + ipath_cdbg(VERBOSE, "IBReset %s xgxsconfig %llx\n", + was_reset ? "Asserted" : "Negated", (unsigned long long) + ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig)); + + if (dd->ipath_boardrev) { + /* + * Hardware is not emulator, and may have been reset. Init it. + * Below will release reset, but needs to know if chip was + * originally in reset, to only trim DACs on first time + * after chip reset or powercycle (not driver reload) + */ + ret = ipath_sd7220_init(dd, was_reset); + } + + val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig); + prev_val = val; + val |= INFINIPATH_XGXS_FC_SAFE; + if (val != prev_val) { + ipath_write_kreg(dd, dd->ipath_kregs->kr_xgxsconfig, val); + ipath_read_kreg32(dd, dd->ipath_kregs->kr_scratch); + } + if (val & INFINIPATH_XGXS_RESET) + val &= ~INFINIPATH_XGXS_RESET; + if (val != prev_val) + ipath_write_kreg(dd, dd->ipath_kregs->kr_xgxsconfig, val); + + ipath_cdbg(VERBOSE, "done: xgxs=%llx from %llx\n", + (unsigned long long) + ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig), + prev_val); + + guid = be64_to_cpu(dd->ipath_guid); + + if (!guid) { + /* have to have something, so use likely unique tsc */ + guid = get_cycles(); + ipath_dbg("No GUID for heartbeat, faking %llx\n", + (unsigned long long)guid); + } else + ipath_cdbg(VERBOSE, "Wrote %llX to HRTBT_GUID\n", guid); + ipath_write_kreg(dd, dd->ipath_kregs->kr_hrtbt_guid, guid); + return ret; +} + +static void ipath_7220_config_jint(struct ipath_devdata *dd, + u16 idle_ticks, u16 max_packets) +{ + + /* + * We can request a receive interrupt for 1 or more packets + * from current offset. + */ + if (idle_ticks == 0 || max_packets == 0) + /* interrupt after one packet if no mitigation */ + dd->ipath_rhdrhead_intr_off = + 1ULL << IBA7220_HDRHEAD_PKTINT_SHIFT; + else + /* Turn off RcvHdrHead interrupts if using mitigation */ + dd->ipath_rhdrhead_intr_off = 0ULL; + + /* refresh kernel RcvHdrHead registers... */ + ipath_write_ureg(dd, ur_rcvhdrhead, + dd->ipath_rhdrhead_intr_off | + dd->ipath_pd[0]->port_head, 0); + + dd->ipath_jint_max_packets = max_packets; + dd->ipath_jint_idle_ticks = idle_ticks; + ipath_write_kreg(dd, dd->ipath_kregs->kr_jintreload, + ((u64) max_packets << INFINIPATH_JINT_PACKETSHIFT) | + idle_ticks); +} + +/** + * ipath_7220_quiet_serdes - set serdes to txidle + * @dd: the infinipath device + * Called when driver is being unloaded + */ +static void ipath_7220_quiet_serdes(struct ipath_devdata *dd) +{ + u64 val; + dd->ipath_flags &= ~IPATH_IB_AUTONEG_INPROG; + wake_up(&dd->ipath_autoneg_wait); + cancel_delayed_work(&dd->ipath_autoneg_work); + flush_scheduled_work(); + ipath_shutdown_relock_poll(dd); + val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig); + val |= INFINIPATH_XGXS_RESET; + ipath_write_kreg(dd, dd->ipath_kregs->kr_xgxsconfig, val); +} + +static int ipath_7220_intconfig(struct ipath_devdata *dd) +{ + ipath_7220_config_jint(dd, dd->ipath_jint_idle_ticks, + dd->ipath_jint_max_packets); + return 0; +} + +/** + * ipath_setup_7220_setextled - set the state of the two external LEDs + * @dd: the infinipath device + * @lst: the L state + * @ltst: the LT state + * + * These LEDs indicate the physical and logical state of IB link. + * For this chip (at least with recommended board pinouts), LED1 + * is Yellow (logical state) and LED2 is Green (physical state), + * + * Note: We try to match the Mellanox HCA LED behavior as best + * we can. Green indicates physical link state is OK (something is + * plugged in, and we can train). + * Amber indicates the link is logically up (ACTIVE). + * Mellanox further blinks the amber LED to indicate data packet + * activity, but we have no hardware support for that, so it would + * require waking up every 10-20 msecs and checking the counters + * on the chip, and then turning the LED off if appropriate. That's + * visible overhead, so not something we will do. + * + */ +static void ipath_setup_7220_setextled(struct ipath_devdata *dd, u64 lst, + u64 ltst) +{ + u64 extctl, ledblink = 0; + unsigned long flags = 0; + + /* the diags use the LED to indicate diag info, so we leave + * the external LED alone when the diags are running */ + if (ipath_diag_inuse) + return; + + /* Allow override of LED display for, e.g. Locating system in rack */ + if (dd->ipath_led_override) { + ltst = (dd->ipath_led_override & IPATH_LED_PHYS) + ? INFINIPATH_IBCS_LT_STATE_LINKUP + : INFINIPATH_IBCS_LT_STATE_DISABLED; + lst = (dd->ipath_led_override & IPATH_LED_LOG) + ? INFINIPATH_IBCS_L_STATE_ACTIVE + : INFINIPATH_IBCS_L_STATE_DOWN; + } + + spin_lock_irqsave(&dd->ipath_gpio_lock, flags); + extctl = dd->ipath_extctrl & ~(INFINIPATH_EXTC_LED1PRIPORT_ON | + INFINIPATH_EXTC_LED2PRIPORT_ON); + if (ltst == INFINIPATH_IBCS_LT_STATE_LINKUP) { + extctl |= INFINIPATH_EXTC_LED1PRIPORT_ON; + /* + * counts are in chip clock (4ns) periods. + * This is 1/16 sec (66.6ms) on, + * 3/16 sec (187.5 ms) off, with packets rcvd + */ + ledblink = ((66600*1000UL/4) << IBA7220_LEDBLINK_ON_SHIFT) + | ((187500*1000UL/4) << IBA7220_LEDBLINK_OFF_SHIFT); + } + if (lst == INFINIPATH_IBCS_L_STATE_ACTIVE) + extctl |= INFINIPATH_EXTC_LED2PRIPORT_ON; + dd->ipath_extctrl = extctl; + ipath_write_kreg(dd, dd->ipath_kregs->kr_extctrl, extctl); + spin_unlock_irqrestore(&dd->ipath_gpio_lock, flags); + + if (ledblink) /* blink the LED on packet receive */ + ipath_write_kreg(dd, dd->ipath_kregs->kr_rcvpktledcnt, + ledblink); +} + +/* + * Similar to pci_intx(pdev, 1), except that we make sure + * msi is off... + */ +static void ipath_enable_intx(struct pci_dev *pdev) +{ + u16 cw, new; + int pos; + + /* first, turn on INTx */ + pci_read_config_word(pdev, PCI_COMMAND, &cw); + new = cw & ~PCI_COMMAND_INTX_DISABLE; + if (new != cw) + pci_write_config_word(pdev, PCI_COMMAND, new); + + /* then turn off MSI */ + pos = pci_find_capability(pdev, PCI_CAP_ID_MSI); + if (pos) { + pci_read_config_word(pdev, pos + PCI_MSI_FLAGS, &cw); + new = cw & ~PCI_MSI_FLAGS_ENABLE; + if (new != cw) + pci_write_config_word(pdev, pos + PCI_MSI_FLAGS, new); + } +} + +static int ipath_msi_enabled(struct pci_dev *pdev) +{ + int pos, ret = 0; + + pos = pci_find_capability(pdev, PCI_CAP_ID_MSI); + if (pos) { + u16 cw; + + pci_read_config_word(pdev, pos + PCI_MSI_FLAGS, &cw); + ret = !!(cw & PCI_MSI_FLAGS_ENABLE); + } + return ret; +} + +/* + * disable msi interrupt if enabled, and clear the flag. + * flag is used primarily for the fallback to INTx, but + * is also used in reinit after reset as a flag. + */ +static void ipath_7220_nomsi(struct ipath_devdata *dd) +{ + dd->ipath_msi_lo = 0; + + if (ipath_msi_enabled(dd->pcidev)) { + /* + * free, but don't zero; later kernels require + * it be freed before disable_msi, so the intx + * setup has to request it again. + */ + if (dd->ipath_irq) + free_irq(dd->ipath_irq, dd); + pci_disable_msi(dd->pcidev); + } +} + +/* + * ipath_setup_7220_cleanup - clean up any per-chip chip-specific stuff + * @dd: the infinipath device + * + * Nothing but msi interrupt cleanup for now. + * + * This is called during driver unload. + */ +static void ipath_setup_7220_cleanup(struct ipath_devdata *dd) +{ + ipath_7220_nomsi(dd); +} + + +static void ipath_7220_pcie_params(struct ipath_devdata *dd, u32 boardrev) +{ + u16 linkstat, minwidth, speed; + int pos; + + pos = pci_find_capability(dd->pcidev, PCI_CAP_ID_EXP); + if (!pos) { + ipath_dev_err(dd, "Can't find PCI Express capability!\n"); + goto bail; + } + + pci_read_config_word(dd->pcidev, pos + PCI_EXP_LNKSTA, + &linkstat); + /* + * speed is bits 0-4, linkwidth is bits 4-8 + * no defines for them in headers + */ + speed = linkstat & 0xf; + linkstat >>= 4; + linkstat &= 0x1f; + dd->ipath_lbus_width = linkstat; + switch (boardrev) { + case 0: + case 2: + case 10: + case 12: + minwidth = 16; /* x16 capable boards */ + break; + default: + minwidth = 8; /* x8 capable boards */ + break; + } + + switch (speed) { + case 1: + dd->ipath_lbus_speed = 2500; /* Gen1, 2.5GHz */ + break; + case 2: + dd->ipath_lbus_speed = 5000; /* Gen1, 5GHz */ + break; + default: /* not defined, assume gen1 */ + dd->ipath_lbus_speed = 2500; + break; + } + + if (linkstat < minwidth) + ipath_dev_err(dd, + "PCIe width %u (x%u HCA), performance " + "reduced\n", linkstat, minwidth); + else + ipath_cdbg(VERBOSE, "PCIe speed %u width %u (x%u HCA)\n", + dd->ipath_lbus_speed, linkstat, minwidth); + + if (speed != 1) + ipath_dev_err(dd, + "PCIe linkspeed %u is incorrect; " + "should be 1 (2500)!\n", speed); + +bail: + /* fill in string, even on errors */ + snprintf(dd->ipath_lbus_info, sizeof(dd->ipath_lbus_info), + "PCIe,%uMHz,x%u\n", + dd->ipath_lbus_speed, + dd->ipath_lbus_width); + return; +} + + +/** + * ipath_setup_7220_config - setup PCIe config related stuff + * @dd: the infinipath device + * @pdev: the PCI device + * + * The pci_enable_msi() call will fail on systems with MSI quirks + * such as those with AMD8131, even if the device of interest is not + * attached to that device, (in the 2.6.13 - 2.6.15 kernels, at least, fixed + * late in 2.6.16). + * All that can be done is to edit the kernel source to remove the quirk + * check until that is fixed. + * We do not need to call enable_msi() for our HyperTransport chip, + * even though it uses MSI, and we want to avoid the quirk warning, so + * So we call enable_msi only for PCIe. If we do end up needing + * pci_enable_msi at some point in the future for HT, we'll move the + * call back into the main init_one code. + * We save the msi lo and hi values, so we can restore them after + * chip reset (the kernel PCI infrastructure doesn't yet handle that + * correctly). + */ +static int ipath_setup_7220_config(struct ipath_devdata *dd, + struct pci_dev *pdev) +{ + int pos, ret = -1; + u32 boardrev; + + dd->ipath_msi_lo = 0; /* used as a flag during reset processing */ + + pos = pci_find_capability(pdev, PCI_CAP_ID_MSI); + if (!strcmp(int_type, "force_msi") || !strcmp(int_type, "auto")) + ret = pci_enable_msi(pdev); + if (ret) { + if (!strcmp(int_type, "force_msi")) { + ipath_dev_err(dd, "pci_enable_msi failed: %d, " + "force_msi is on, so not continuing.\n", + ret); + return ret; + } + + ipath_enable_intx(pdev); + if (!strcmp(int_type, "auto")) + ipath_dev_err(dd, "pci_enable_msi failed: %d, " + "falling back to INTx\n", ret); + } else if (pos) { + u16 control; + pci_read_config_dword(pdev, pos + PCI_MSI_ADDRESS_LO, + &dd->ipath_msi_lo); + pci_read_config_dword(pdev, pos + PCI_MSI_ADDRESS_HI, + &dd->ipath_msi_hi); + pci_read_config_word(pdev, pos + PCI_MSI_FLAGS, + &control); + /* now save the data (vector) info */ + pci_read_config_word(pdev, + pos + ((control & PCI_MSI_FLAGS_64BIT) + ? PCI_MSI_DATA_64 : + PCI_MSI_DATA_32), + &dd->ipath_msi_data); + } else + ipath_dev_err(dd, "Can't find MSI capability, " + "can't save MSI settings for reset\n"); + + dd->ipath_irq = pdev->irq; + + /* + * We save the cachelinesize also, although it doesn't + * really matter. + */ + pci_read_config_byte(pdev, PCI_CACHE_LINE_SIZE, + &dd->ipath_pci_cacheline); + + /* + * this function called early, ipath_boardrev not set yet. Can't + * use ipath_read_kreg64() yet, too early in init, so use readq() + */ + boardrev = (readq(&dd->ipath_kregbase[dd->ipath_kregs->kr_revision]) + >> INFINIPATH_R_BOARDID_SHIFT) & INFINIPATH_R_BOARDID_MASK; + + ipath_7220_pcie_params(dd, boardrev); + + dd->ipath_flags |= IPATH_NODMA_RTAIL | IPATH_HAS_SEND_DMA | + IPATH_HAS_PBC_CNT | IPATH_HAS_THRESH_UPDATE; + dd->ipath_pioupd_thresh = 4U; /* set default update threshold */ + return 0; +} + +static void ipath_init_7220_variables(struct ipath_devdata *dd) +{ + /* + * setup the register offsets, since they are different for each + * chip + */ + dd->ipath_kregs = &ipath_7220_kregs; + dd->ipath_cregs = &ipath_7220_cregs; + + /* + * bits for selecting i2c direction and values, + * used for I2C serial flash + */ + dd->ipath_gpio_sda_num = _IPATH_GPIO_SDA_NUM; + dd->ipath_gpio_scl_num = _IPATH_GPIO_SCL_NUM; + dd->ipath_gpio_sda = IPATH_GPIO_SDA; + dd->ipath_gpio_scl = IPATH_GPIO_SCL; + + /* + * Fill in data for field-values that change in IBA7220. + * We dynamically specify only the mask for LINKTRAININGSTATE + * and only the shift for LINKSTATE, as they are the only ones + * that change. Also precalculate the 3 link states of interest + * and the combined mask. + */ + dd->ibcs_ls_shift = IBA7220_IBCS_LINKSTATE_SHIFT; + dd->ibcs_lts_mask = IBA7220_IBCS_LINKTRAININGSTATE_MASK; + dd->ibcs_mask = (INFINIPATH_IBCS_LINKSTATE_MASK << + dd->ibcs_ls_shift) | dd->ibcs_lts_mask; + dd->ib_init = (INFINIPATH_IBCS_LT_STATE_LINKUP << + INFINIPATH_IBCS_LINKTRAININGSTATE_SHIFT) | + (INFINIPATH_IBCS_L_STATE_INIT << dd->ibcs_ls_shift); + dd->ib_arm = (INFINIPATH_IBCS_LT_STATE_LINKUP << + INFINIPATH_IBCS_LINKTRAININGSTATE_SHIFT) | + (INFINIPATH_IBCS_L_STATE_ARM << dd->ibcs_ls_shift); + dd->ib_active = (INFINIPATH_IBCS_LT_STATE_LINKUP << + INFINIPATH_IBCS_LINKTRAININGSTATE_SHIFT) | + (INFINIPATH_IBCS_L_STATE_ACTIVE << dd->ibcs_ls_shift); + + /* + * Fill in data for ibcc field-values that change in IBA7220. + * We dynamically specify only the mask for LINKINITCMD + * and only the shift for LINKCMD and MAXPKTLEN, as they are + * the only ones that change. + */ + dd->ibcc_lic_mask = IBA7220_IBCC_LINKINITCMD_MASK; + dd->ibcc_lc_shift = IBA7220_IBCC_LINKCMD_SHIFT; + dd->ibcc_mpl_shift = IBA7220_IBCC_MAXPKTLEN_SHIFT; + + /* Fill in shifts for RcvCtrl. */ + dd->ipath_r_portenable_shift = INFINIPATH_R_PORTENABLE_SHIFT; + dd->ipath_r_intravail_shift = IBA7220_R_INTRAVAIL_SHIFT; + dd->ipath_r_tailupd_shift = IBA7220_R_TAILUPD_SHIFT; + dd->ipath_r_portcfg_shift = IBA7220_R_PORTCFG_SHIFT; + + /* variables for sanity checking interrupt and errors */ + dd->ipath_hwe_bitsextant = + (INFINIPATH_HWE_RXEMEMPARITYERR_MASK << + INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT) | + (INFINIPATH_HWE_TXEMEMPARITYERR_MASK << + INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT) | + (INFINIPATH_HWE_PCIEMEMPARITYERR_MASK << + INFINIPATH_HWE_PCIEMEMPARITYERR_SHIFT) | + INFINIPATH_HWE_PCIE1PLLFAILED | + INFINIPATH_HWE_PCIE0PLLFAILED | + INFINIPATH_HWE_PCIEPOISONEDTLP | + INFINIPATH_HWE_PCIECPLTIMEOUT | + INFINIPATH_HWE_PCIEBUSPARITYXTLH | + INFINIPATH_HWE_PCIEBUSPARITYXADM | + INFINIPATH_HWE_PCIEBUSPARITYRADM | + INFINIPATH_HWE_MEMBISTFAILED | + INFINIPATH_HWE_COREPLL_FBSLIP | + INFINIPATH_HWE_COREPLL_RFSLIP | + INFINIPATH_HWE_SERDESPLLFAILED | + INFINIPATH_HWE_IBCBUSTOSPCPARITYERR | + INFINIPATH_HWE_IBCBUSFRSPCPARITYERR | + INFINIPATH_HWE_PCIECPLDATAQUEUEERR | + INFINIPATH_HWE_PCIECPLHDRQUEUEERR | + INFINIPATH_HWE_SDMAMEMREADERR | + INFINIPATH_HWE_CLK_UC_PLLNOTLOCKED | + INFINIPATH_HWE_PCIESERDESQ0PCLKNOTDETECT | + INFINIPATH_HWE_PCIESERDESQ1PCLKNOTDETECT | + INFINIPATH_HWE_PCIESERDESQ2PCLKNOTDETECT | + INFINIPATH_HWE_PCIESERDESQ3PCLKNOTDETECT | + INFINIPATH_HWE_DDSRXEQMEMORYPARITYERR | + INFINIPATH_HWE_IB_UC_MEMORYPARITYERR | + INFINIPATH_HWE_PCIE_UC_OCT0MEMORYPARITYERR | + INFINIPATH_HWE_PCIE_UC_OCT1MEMORYPARITYERR; + dd->ipath_i_bitsextant = + INFINIPATH_I_SDMAINT | INFINIPATH_I_SDMADISABLED | + (INFINIPATH_I_RCVURG_MASK << INFINIPATH_I_RCVURG_SHIFT) | + (INFINIPATH_I_RCVAVAIL_MASK << + INFINIPATH_I_RCVAVAIL_SHIFT) | + INFINIPATH_I_ERROR | INFINIPATH_I_SPIOSENT | + INFINIPATH_I_SPIOBUFAVAIL | INFINIPATH_I_GPIO | + INFINIPATH_I_JINT | INFINIPATH_I_SERDESTRIMDONE; + dd->ipath_e_bitsextant = + INFINIPATH_E_RFORMATERR | INFINIPATH_E_RVCRC | + INFINIPATH_E_RICRC | INFINIPATH_E_RMINPKTLEN | + INFINIPATH_E_RMAXPKTLEN | INFINIPATH_E_RLONGPKTLEN | + INFINIPATH_E_RSHORTPKTLEN | INFINIPATH_E_RUNEXPCHAR | + INFINIPATH_E_RUNSUPVL | INFINIPATH_E_REBP | + INFINIPATH_E_RIBFLOW | INFINIPATH_E_RBADVERSION | + INFINIPATH_E_RRCVEGRFULL | INFINIPATH_E_RRCVHDRFULL | + INFINIPATH_E_RBADTID | INFINIPATH_E_RHDRLEN | + INFINIPATH_E_RHDR | INFINIPATH_E_RIBLOSTLINK | + INFINIPATH_E_SENDSPECIALTRIGGER | + INFINIPATH_E_SDMADISABLED | INFINIPATH_E_SMINPKTLEN | + INFINIPATH_E_SMAXPKTLEN | INFINIPATH_E_SUNDERRUN | + INFINIPATH_E_SPKTLEN | INFINIPATH_E_SDROPPEDSMPPKT | + INFINIPATH_E_SDROPPEDDATAPKT | + INFINIPATH_E_SPIOARMLAUNCH | INFINIPATH_E_SUNEXPERRPKTNUM | + INFINIPATH_E_SUNSUPVL | INFINIPATH_E_SENDBUFMISUSE | + INFINIPATH_E_SDMAGENMISMATCH | INFINIPATH_E_SDMAOUTOFBOUND | + INFINIPATH_E_SDMATAILOUTOFBOUND | INFINIPATH_E_SDMABASE | + INFINIPATH_E_SDMA1STDESC | INFINIPATH_E_SDMARPYTAG | + INFINIPATH_E_SDMADWEN | INFINIPATH_E_SDMAMISSINGDW | + INFINIPATH_E_SDMAUNEXPDATA | + INFINIPATH_E_IBSTATUSCHANGED | INFINIPATH_E_INVALIDADDR | + INFINIPATH_E_RESET | INFINIPATH_E_HARDWARE | + INFINIPATH_E_SDMADESCADDRMISALIGN | + INFINIPATH_E_INVALIDEEPCMD; + + dd->ipath_i_rcvavail_mask = INFINIPATH_I_RCVAVAIL_MASK; + dd->ipath_i_rcvurg_mask = INFINIPATH_I_RCVURG_MASK; + dd->ipath_i_rcvavail_shift = INFINIPATH_I_RCVAVAIL_SHIFT; + dd->ipath_i_rcvurg_shift = INFINIPATH_I_RCVURG_SHIFT; + dd->ipath_flags |= IPATH_INTREG_64 | IPATH_HAS_MULT_IB_SPEED + | IPATH_HAS_LINK_LATENCY; + + /* + * EEPROM error log 0 is TXE Parity errors. 1 is RXE Parity. + * 2 is Some Misc, 3 is reserved for future. + */ + dd->ipath_eep_st_masks[0].hwerrs_to_log = + INFINIPATH_HWE_TXEMEMPARITYERR_MASK << + INFINIPATH_HWE_TXEMEMPARITYERR_SHIFT; + + dd->ipath_eep_st_masks[1].hwerrs_to_log = + INFINIPATH_HWE_RXEMEMPARITYERR_MASK << + INFINIPATH_HWE_RXEMEMPARITYERR_SHIFT; + + dd->ipath_eep_st_masks[2].errs_to_log = INFINIPATH_E_RESET; + + ipath_linkrecovery = 0; + + init_waitqueue_head(&dd->ipath_autoneg_wait); + INIT_DELAYED_WORK(&dd->ipath_autoneg_work, autoneg_work); + + dd->ipath_link_width_supported = IB_WIDTH_1X | IB_WIDTH_4X; + dd->ipath_link_speed_supported = IPATH_IB_SDR | IPATH_IB_DDR; + + dd->ipath_link_width_enabled = dd->ipath_link_width_supported; + dd->ipath_link_speed_enabled = dd->ipath_link_speed_supported; + /* + * set the initial values to reasonable default, will be set + * for real when link is up. + */ + dd->ipath_link_width_active = IB_WIDTH_4X; + dd->ipath_link_speed_active = IPATH_IB_SDR; + dd->delay_mult = rate_to_delay[0][1]; +} + + +/* + * Setup the MSI stuff again after a reset. I'd like to just call + * pci_enable_msi() and request_irq() again, but when I do that, + * the MSI enable bit doesn't get set in the command word, and + * we switch to to a different interrupt vector, which is confusing, + * so I instead just do it all inline. Perhaps somehow can tie this + * into the PCIe hotplug support at some point + * Note, because I'm doing it all here, I don't call pci_disable_msi() + * or free_irq() at the start of ipath_setup_7220_reset(). + */ +static int ipath_reinit_msi(struct ipath_devdata *dd) +{ + int ret = 0; + + int pos; + u16 control; + if (!dd->ipath_msi_lo) /* Using intX, or init problem */ + goto bail; + + pos = pci_find_capability(dd->pcidev, PCI_CAP_ID_MSI); + if (!pos) { + ipath_dev_err(dd, "Can't find MSI capability, " + "can't restore MSI settings\n"); + goto bail; + } + ipath_cdbg(VERBOSE, "Writing msi_lo 0x%x to config offset 0x%x\n", + dd->ipath_msi_lo, pos + PCI_MSI_ADDRESS_LO); + pci_write_config_dword(dd->pcidev, pos + PCI_MSI_ADDRESS_LO, + dd->ipath_msi_lo); + ipath_cdbg(VERBOSE, "Writing msi_lo 0x%x to config offset 0x%x\n", + dd->ipath_msi_hi, pos + PCI_MSI_ADDRESS_HI); + pci_write_config_dword(dd->pcidev, pos + PCI_MSI_ADDRESS_HI, + dd->ipath_msi_hi); + pci_read_config_word(dd->pcidev, pos + PCI_MSI_FLAGS, &control); + if (!(control & PCI_MSI_FLAGS_ENABLE)) { + ipath_cdbg(VERBOSE, "MSI control at off %x was %x, " + "setting MSI enable (%x)\n", pos + PCI_MSI_FLAGS, + control, control | PCI_MSI_FLAGS_ENABLE); + control |= PCI_MSI_FLAGS_ENABLE; + pci_write_config_word(dd->pcidev, pos + PCI_MSI_FLAGS, + control); + } + /* now rewrite the data (vector) info */ + pci_write_config_word(dd->pcidev, pos + + ((control & PCI_MSI_FLAGS_64BIT) ? 12 : 8), + dd->ipath_msi_data); + ret = 1; + +bail: + if (!ret) { + ipath_dbg("Using INTx, MSI disabled or not configured\n"); + ipath_enable_intx(dd->pcidev); + ret = 1; + } + /* + * We restore the cachelinesize also, although it doesn't really + * matter. + */ + pci_write_config_byte(dd->pcidev, PCI_CACHE_LINE_SIZE, + dd->ipath_pci_cacheline); + /* and now set the pci master bit again */ + pci_set_master(dd->pcidev); + + return ret; +} + +/* + * This routine sleeps, so it can only be called from user context, not + * from interrupt context. If we need interrupt context, we can split + * it into two routines. + */ +static int ipath_setup_7220_reset(struct ipath_devdata *dd) +{ + u64 val; + int i; + int ret; + u16 cmdval; + + pci_read_config_word(dd->pcidev, PCI_COMMAND, &cmdval); + + /* Use dev_err so it shows up in logs, etc. */ + ipath_dev_err(dd, "Resetting InfiniPath unit %u\n", dd->ipath_unit); + + /* keep chip from being accessed in a few places */ + dd->ipath_flags &= ~(IPATH_INITTED | IPATH_PRESENT); + val = dd->ipath_control | INFINIPATH_C_RESET; + ipath_write_kreg(dd, dd->ipath_kregs->kr_control, val); + mb(); + + for (i = 1; i <= 5; i++) { + int r; + + /* + * Allow MBIST, etc. to complete; longer on each retry. + * We sometimes get machine checks from bus timeout if no + * response, so for now, make it *really* long. + */ + msleep(1000 + (1 + i) * 2000); + r = pci_write_config_dword(dd->pcidev, PCI_BASE_ADDRESS_0, + dd->ipath_pcibar0); + if (r) + ipath_dev_err(dd, "rewrite of BAR0 failed: %d\n", r); + r = pci_write_config_dword(dd->pcidev, PCI_BASE_ADDRESS_1, + dd->ipath_pcibar1); + if (r) + ipath_dev_err(dd, "rewrite of BAR1 failed: %d\n", r); + /* now re-enable memory access */ + pci_write_config_word(dd->pcidev, PCI_COMMAND, cmdval); + r = pci_enable_device(dd->pcidev); + if (r) + ipath_dev_err(dd, "pci_enable_device failed after " + "reset: %d\n", r); + /* + * whether it fully enabled or not, mark as present, + * again (but not INITTED) + */ + dd->ipath_flags |= IPATH_PRESENT; + val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_revision); + if (val == dd->ipath_revision) { + ipath_cdbg(VERBOSE, "Got matching revision " + "register %llx on try %d\n", + (unsigned long long) val, i); + ret = ipath_reinit_msi(dd); + goto bail; + } + /* Probably getting -1 back */ + ipath_dbg("Didn't get expected revision register, " + "got %llx, try %d\n", (unsigned long long) val, + i + 1); + } + ret = 0; /* failed */ + +bail: + if (ret) + ipath_7220_pcie_params(dd, dd->ipath_boardrev); + + return ret; +} + +/** + * ipath_7220_put_tid - write a TID to the chip + * @dd: the infinipath device + * @tidptr: pointer to the expected TID (in chip) to udpate + * @tidtype: 0 for eager, 1 for expected + * @pa: physical address of in memory buffer; ipath_tidinvalid if freeing + * + * This exists as a separate routine to allow for selection of the + * appropriate "flavor". The static calls in cleanup just use the + * revision-agnostic form, as they are not performance critical. + */ +static void ipath_7220_put_tid(struct ipath_devdata *dd, u64 __iomem *tidptr, + u32 type, unsigned long pa) +{ + if (pa != dd->ipath_tidinvalid) { + u64 chippa = pa >> IBA7220_TID_PA_SHIFT; + + /* paranoia checks */ + if (pa != (chippa << IBA7220_TID_PA_SHIFT)) { + dev_info(&dd->pcidev->dev, "BUG: physaddr %lx " + "not 2KB aligned!\n", pa); + return; + } + if (pa >= (1UL << IBA7220_TID_SZ_SHIFT)) { + ipath_dev_err(dd, + "BUG: Physical page address 0x%lx " + "larger than supported\n", pa); + return; + } + + if (type == RCVHQ_RCV_TYPE_EAGER) + chippa |= dd->ipath_tidtemplate; + else /* for now, always full 4KB page */ + chippa |= IBA7220_TID_SZ_4K; + writeq(chippa, tidptr); + } else + writeq(pa, tidptr); + mmiowb(); +} + +/** + * ipath_7220_clear_tid - clear all TID entries for a port, expected and eager + * @dd: the infinipath device + * @port: the port + * + * clear all TID entries for a port, expected and eager. + * Used from ipath_close(). On this chip, TIDs are only 32 bits, + * not 64, but they are still on 64 bit boundaries, so tidbase + * is declared as u64 * for the pointer math, even though we write 32 bits + */ +static void ipath_7220_clear_tids(struct ipath_devdata *dd, unsigned port) +{ + u64 __iomem *tidbase; + unsigned long tidinv; + int i; + + if (!dd->ipath_kregbase) + return; + + ipath_cdbg(VERBOSE, "Invalidate TIDs for port %u\n", port); + + tidinv = dd->ipath_tidinvalid; + tidbase = (u64 __iomem *) + ((char __iomem *)(dd->ipath_kregbase) + + dd->ipath_rcvtidbase + + port * dd->ipath_rcvtidcnt * sizeof(*tidbase)); + + for (i = 0; i < dd->ipath_rcvtidcnt; i++) + ipath_7220_put_tid(dd, &tidbase[i], RCVHQ_RCV_TYPE_EXPECTED, + tidinv); + + tidbase = (u64 __iomem *) + ((char __iomem *)(dd->ipath_kregbase) + + dd->ipath_rcvegrbase + port_egrtid_idx(dd, port) + * sizeof(*tidbase)); + + for (i = port ? dd->ipath_rcvegrcnt : dd->ipath_p0_rcvegrcnt; i; i--) + ipath_7220_put_tid(dd, &tidbase[i-1], RCVHQ_RCV_TYPE_EAGER, + tidinv); +} + +/** + * ipath_7220_tidtemplate - setup constants for TID updates + * @dd: the infinipath device + * + * We setup stuff that we use a lot, to avoid calculating each time + */ +static void ipath_7220_tidtemplate(struct ipath_devdata *dd) +{ + /* For now, we always allocate 4KB buffers (at init) so we can + * receive max size packets. We may want a module parameter to + * specify 2KB or 4KB and/or make be per port instead of per device + * for those who want to reduce memory footprint. Note that the + * ipath_rcvhdrentsize size must be large enough to hold the largest + * IB header (currently 96 bytes) that we expect to handle (plus of + * course the 2 dwords of RHF). + */ + if (dd->ipath_rcvegrbufsize == 2048) + dd->ipath_tidtemplate = IBA7220_TID_SZ_2K; + else if (dd->ipath_rcvegrbufsize == 4096) + dd->ipath_tidtemplate = IBA7220_TID_SZ_4K; + else { + dev_info(&dd->pcidev->dev, "BUG: unsupported egrbufsize " + "%u, using %u\n", dd->ipath_rcvegrbufsize, + 4096); + dd->ipath_tidtemplate = IBA7220_TID_SZ_4K; + } + dd->ipath_tidinvalid = 0; +} + +static int ipath_7220_early_init(struct ipath_devdata *dd) +{ + u32 i, s; + + if (strcmp(int_type, "auto") && + strcmp(int_type, "force_msi") && + strcmp(int_type, "force_intx")) { + ipath_dev_err(dd, "Invalid interrupt_type: '%s', expecting " + "auto, force_msi or force_intx\n", int_type); + return -EINVAL; + } + + /* + * Control[4] has been added to change the arbitration within + * the SDMA engine between favoring data fetches over descriptor + * fetches. ipath_sdma_fetch_arb==0 gives data fetches priority. + */ + if (ipath_sdma_fetch_arb && (dd->ipath_minrev > 1)) + dd->ipath_control |= 1<<4; + + dd->ipath_flags |= IPATH_4BYTE_TID; + + /* + * For openfabrics, we need to be able to handle an IB header of + * 24 dwords. HT chip has arbitrary sized receive buffers, so we + * made them the same size as the PIO buffers. This chip does not + * handle arbitrary size buffers, so we need the header large enough + * to handle largest IB header, but still have room for a 2KB MTU + * standard IB packet. + */ + dd->ipath_rcvhdrentsize = 24; + dd->ipath_rcvhdrsize = IPATH_DFLT_RCVHDRSIZE; + dd->ipath_rhf_offset = + dd->ipath_rcvhdrentsize - sizeof(u64) / sizeof(u32); + + dd->ipath_rcvegrbufsize = ipath_mtu4096 ? 4096 : 2048; + /* + * the min() check here is currently a nop, but it may not always + * be, depending on just how we do ipath_rcvegrbufsize + */ + dd->ipath_ibmaxlen = min(ipath_mtu4096 ? dd->ipath_piosize4k : + dd->ipath_piosize2k, + dd->ipath_rcvegrbufsize + + (dd->ipath_rcvhdrentsize << 2)); + dd->ipath_init_ibmaxlen = dd->ipath_ibmaxlen; + + ipath_7220_config_jint(dd, INFINIPATH_JINT_DEFAULT_IDLE_TICKS, + INFINIPATH_JINT_DEFAULT_MAX_PACKETS); + + if (dd->ipath_boardrev) /* no eeprom on emulator */ + ipath_get_eeprom_info(dd); + + /* start of code to check and print procmon */ + s = ipath_read_kreg32(dd, IPATH_KREG_OFFSET(ProcMon)); + s &= ~(1U<<31); /* clear done bit */ + s |= 1U<<14; /* clear counter (write 1 to clear) */ + ipath_write_kreg(dd, IPATH_KREG_OFFSET(ProcMon), s); + /* make sure clear_counter low long enough before start */ + ipath_read_kreg32(dd, dd->ipath_kregs->kr_scratch); + ipath_read_kreg32(dd, dd->ipath_kregs->kr_scratch); + + s &= ~(1U<<14); /* allow counter to count (before starting) */ + ipath_write_kreg(dd, IPATH_KREG_OFFSET(ProcMon), s); + ipath_read_kreg32(dd, dd->ipath_kregs->kr_scratch); + ipath_read_kreg32(dd, dd->ipath_kregs->kr_scratch); + s = ipath_read_kreg32(dd, IPATH_KREG_OFFSET(ProcMon)); + + s |= 1U<<15; /* start the counter */ + s &= ~(1U<<31); /* clear done bit */ + s &= ~0x7ffU; /* clear frequency bits */ + s |= 0xe29; /* set frequency bits, in case cleared */ + ipath_write_kreg(dd, IPATH_KREG_OFFSET(ProcMon), s); + + s = 0; + for (i = 500; i > 0 && !(s&(1ULL<<31)); i--) { + ipath_read_kreg32(dd, dd->ipath_kregs->kr_scratch); + s = ipath_read_kreg32(dd, IPATH_KREG_OFFSET(ProcMon)); + } + if (!(s&(1U<<31))) + ipath_dev_err(dd, "ProcMon register not valid: 0x%x\n", s); + else + ipath_dbg("ProcMon=0x%x, count=0x%x\n", s, (s>>16)&0x1ff); + + return 0; +} + +/** + * ipath_init_7220_get_base_info - set chip-specific flags for user code + * @pd: the infinipath port + * @kbase: ipath_base_info pointer + * + * We set the PCIE flag because the lower bandwidth on PCIe vs + * HyperTransport can affect some user packet algorithims. + */ +static int ipath_7220_get_base_info(struct ipath_portdata *pd, void *kbase) +{ + struct ipath_base_info *kinfo = kbase; + + kinfo->spi_runtime_flags |= + IPATH_RUNTIME_PCIE | IPATH_RUNTIME_NODMA_RTAIL | + IPATH_RUNTIME_SDMA; + + return 0; +} + +static void ipath_7220_free_irq(struct ipath_devdata *dd) +{ + free_irq(dd->ipath_irq, dd); + dd->ipath_irq = 0; +} + +static struct ipath_message_header * +ipath_7220_get_msgheader(struct ipath_devdata *dd, __le32 *rhf_addr) +{ + u32 offset = ipath_hdrget_offset(rhf_addr); + + return (struct ipath_message_header *) + (rhf_addr - dd->ipath_rhf_offset + offset); +} + +static void ipath_7220_config_ports(struct ipath_devdata *dd, ushort cfgports) +{ + u32 nchipports; + + nchipports = ipath_read_kreg32(dd, dd->ipath_kregs->kr_portcnt); + if (!cfgports) { + int ncpus = num_online_cpus(); + + if (ncpus <= 4) + dd->ipath_portcnt = 5; + else if (ncpus <= 8) + dd->ipath_portcnt = 9; + if (dd->ipath_portcnt) + ipath_dbg("Auto-configured for %u ports, %d cpus " + "online\n", dd->ipath_portcnt, ncpus); + } else if (cfgports <= nchipports) + dd->ipath_portcnt = cfgports; + if (!dd->ipath_portcnt) /* none of the above, set to max */ + dd->ipath_portcnt = nchipports; + /* + * chip can be configured for 5, 9, or 17 ports, and choice + * affects number of eager TIDs per port (1K, 2K, 4K). + */ + if (dd->ipath_portcnt > 9) + dd->ipath_rcvctrl |= 2ULL << IBA7220_R_PORTCFG_SHIFT; + else if (dd->ipath_portcnt > 5) + dd->ipath_rcvctrl |= 1ULL << IBA7220_R_PORTCFG_SHIFT; + /* else configure for default 5 receive ports */ + ipath_write_kreg(dd, dd->ipath_kregs->kr_rcvctrl, + dd->ipath_rcvctrl); + dd->ipath_p0_rcvegrcnt = 2048; /* always */ + if (dd->ipath_flags & IPATH_HAS_SEND_DMA) + dd->ipath_pioreserved = 1; /* reserve a buffer */ +} + + +static int ipath_7220_get_ib_cfg(struct ipath_devdata *dd, int which) +{ + int lsb, ret = 0; + u64 maskr; /* right-justified mask */ + + switch (which) { + case IPATH_IB_CFG_HRTBT: /* Get Heartbeat off/enable/auto */ + lsb = IBA7220_IBC_HRTBT_SHIFT; + maskr = IBA7220_IBC_HRTBT_MASK; + break; + + case IPATH_IB_CFG_LWID_ENB: /* Get allowed Link-width */ + ret = dd->ipath_link_width_enabled; + goto done; + + case IPATH_IB_CFG_LWID: /* Get currently active Link-width */ + ret = dd->ipath_link_width_active; + goto done; + + case IPATH_IB_CFG_SPD_ENB: /* Get allowed Link speeds */ + ret = dd->ipath_link_speed_enabled; + goto done; + + case IPATH_IB_CFG_SPD: /* Get current Link spd */ + ret = dd->ipath_link_speed_active; + goto done; + + case IPATH_IB_CFG_RXPOL_ENB: /* Get Auto-RX-polarity enable */ + lsb = IBA7220_IBC_RXPOL_SHIFT; + maskr = IBA7220_IBC_RXPOL_MASK; + break; + + case IPATH_IB_CFG_LREV_ENB: /* Get Auto-Lane-reversal enable */ + lsb = IBA7220_IBC_LREV_SHIFT; + maskr = IBA7220_IBC_LREV_MASK; + break; + + case IPATH_IB_CFG_LINKLATENCY: + ret = ipath_read_kreg64(dd, dd->ipath_kregs->kr_ibcddrstatus) + & IBA7220_DDRSTAT_LINKLAT_MASK; + goto done; + + default: + ret = -ENOTSUPP; + goto done; + } + ret = (int)((dd->ipath_ibcddrctrl >> lsb) & maskr); +done: + return ret; +} + +static int ipath_7220_set_ib_cfg(struct ipath_devdata *dd, int which, u32 val) +{ + int lsb, ret = 0, setforce = 0; + u64 maskr; /* right-justified mask */ + + switch (which) { + case IPATH_IB_CFG_LIDLMC: + /* + * Set LID and LMC. Combined to avoid possible hazard + * caller puts LMC in 16MSbits, DLID in 16LSbits of val + */ + lsb = IBA7220_IBC_DLIDLMC_SHIFT; + maskr = IBA7220_IBC_DLIDLMC_MASK; + break; + + case IPATH_IB_CFG_HRTBT: /* set Heartbeat off/enable/auto */ + if (val & IPATH_IB_HRTBT_ON && + (dd->ipath_flags & IPATH_NO_HRTBT)) + goto bail; + lsb = IBA7220_IBC_HRTBT_SHIFT; + maskr = IBA7220_IBC_HRTBT_MASK; + break; + + case IPATH_IB_CFG_LWID_ENB: /* set allowed Link-width */ + /* + * As with speed, only write the actual register if + * the link is currently down, otherwise takes effect + * on next link change. + */ + dd->ipath_link_width_enabled = val; + if ((dd->ipath_flags & (IPATH_LINKDOWN|IPATH_LINKINIT)) != + IPATH_LINKDOWN) + goto bail; + /* + * We set the IPATH_IB_FORCE_NOTIFY bit so updown + * will get called because we want update + * link_width_active, and the change may not take + * effect for some time (if we are in POLL), so this + * flag will force the updown routine to be called + * on the next ibstatuschange down interrupt, even + * if it's not an down->up transition. + */ + val--; /* convert from IB to chip */ + maskr = IBA7220_IBC_WIDTH_MASK; + lsb = IBA7220_IBC_WIDTH_SHIFT; + setforce = 1; + dd->ipath_flags |= IPATH_IB_FORCE_NOTIFY; + break; + + case IPATH_IB_CFG_SPD_ENB: /* set allowed Link speeds */ + /* + * If we turn off IB1.2, need to preset SerDes defaults, + * but not right now. Set a flag for the next time + * we command the link down. As with width, only write the + * actual register if the link is currently down, otherwise + * takes effect on next link change. Since setting is being + * explictly requested (via MAD or sysfs), clear autoneg + * failure status if speed autoneg is enabled. + */ + dd->ipath_link_speed_enabled = val; + if (dd->ipath_ibcddrctrl & IBA7220_IBC_IBTA_1_2_MASK && + !(val & (val - 1))) + dd->ipath_presets_needed = 1; + if ((dd->ipath_flags & (IPATH_LINKDOWN|IPATH_LINKINIT)) != + IPATH_LINKDOWN) + goto bail; + /* + * We set the IPATH_IB_FORCE_NOTIFY bit so updown + * will get called because we want update + * link_speed_active, and the change may not take + * effect for some time (if we are in POLL), so this + * flag will force the updown routine to be called + * on the next ibstatuschange down interrupt, even + * if it's not an down->up transition. When setting + * speed autoneg, clear AUTONEG_FAILED. + */ + if (val == (IPATH_IB_SDR | IPATH_IB_DDR)) { + val = IBA7220_IBC_SPEED_AUTONEG_MASK | + IBA7220_IBC_IBTA_1_2_MASK; + dd->ipath_flags &= ~IPATH_IB_AUTONEG_FAILED; + } else + val = val == IPATH_IB_DDR ? IBA7220_IBC_SPEED_DDR + : IBA7220_IBC_SPEED_SDR; + maskr = IBA7220_IBC_SPEED_AUTONEG_MASK | + IBA7220_IBC_IBTA_1_2_MASK; + lsb = 0; /* speed bits are low bits */ + setforce = 1; + break; + + case IPATH_IB_CFG_RXPOL_ENB: /* set Auto-RX-polarity enable */ + lsb = IBA7220_IBC_RXPOL_SHIFT; + maskr = IBA7220_IBC_RXPOL_MASK; + break; + + case IPATH_IB_CFG_LREV_ENB: /* set Auto-Lane-reversal enable */ + lsb = IBA7220_IBC_LREV_SHIFT; + maskr = IBA7220_IBC_LREV_MASK; + break; + + default: + ret = -ENOTSUPP; + goto bail; + } + dd->ipath_ibcddrctrl &= ~(maskr << lsb); + dd->ipath_ibcddrctrl |= (((u64) val & maskr) << lsb); + ipath_write_kreg(dd, dd->ipath_kregs->kr_ibcddrctrl, + dd->ipath_ibcddrctrl); + if (setforce) + dd->ipath_flags |= IPATH_IB_FORCE_NOTIFY; +bail: + return ret; +} + +static void ipath_7220_read_counters(struct ipath_devdata *dd, + struct infinipath_counters *cntrs) +{ + u64 *counters = (u64 *) cntrs; + int i; + + for (i = 0; i < sizeof(*cntrs) / sizeof(u64); i++) + counters[i] = ipath_snap_cntr(dd, i); +} + +/* if we are using MSI, try to fallback to INTx */ +static int ipath_7220_intr_fallback(struct ipath_devdata *dd) +{ + if (dd->ipath_msi_lo) { + dev_info(&dd->pcidev->dev, "MSI interrupt not detected," + " trying INTx interrupts\n"); + ipath_7220_nomsi(dd); + ipath_enable_intx(dd->pcidev); + /* + * some newer kernels require free_irq before disable_msi, + * and irq can be changed during disable and intx enable + * and we need to therefore use the pcidev->irq value, + * not our saved MSI value. + */ + dd->ipath_irq = dd->pcidev->irq; + if (request_irq(dd->ipath_irq, ipath_intr, IRQF_SHARED, + IPATH_DRV_NAME, dd)) + ipath_dev_err(dd, + "Could not re-request_irq for INTx\n"); + return 1; + } + return 0; +} + +/* + * reset the XGXS (between serdes and IBC). Slightly less intrusive + * than resetting the IBC or external link state, and useful in some + * cases to cause some retraining. To do this right, we reset IBC + * as well. + */ +static void ipath_7220_xgxs_reset(struct ipath_devdata *dd) +{ + u64 val, prev_val; + + prev_val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig); + val = prev_val | INFINIPATH_XGXS_RESET; + prev_val &= ~INFINIPATH_XGXS_RESET; /* be sure */ + ipath_write_kreg(dd, dd->ipath_kregs->kr_control, + dd->ipath_control & ~INFINIPATH_C_LINKENABLE); + ipath_write_kreg(dd, dd->ipath_kregs->kr_xgxsconfig, val); + ipath_read_kreg32(dd, dd->ipath_kregs->kr_scratch); + ipath_write_kreg(dd, dd->ipath_kregs->kr_xgxsconfig, prev_val); + ipath_write_kreg(dd, dd->ipath_kregs->kr_control, + dd->ipath_control); +} + + +/* Still needs cleanup, too much hardwired stuff */ +static void autoneg_send(struct ipath_devdata *dd, + u32 *hdr, u32 dcnt, u32 *data) +{ + int i; + u64 cnt; + u32 __iomem *piobuf; + u32 pnum; + + i = 0; + cnt = 7 + dcnt + 1; /* 7 dword header, dword data, icrc */ + while (!(piobuf = ipath_getpiobuf(dd, cnt, &pnum))) { + if (i++ > 15) { + ipath_dbg("Couldn't get pio buffer for send\n"); + return; + } + udelay(2); + } + if (dd->ipath_flags&IPATH_HAS_PBC_CNT) + cnt |= 0x80000000UL<<32; /* mark as VL15 */ + writeq(cnt, piobuf); + ipath_flush_wc(); + __iowrite32_copy(piobuf + 2, hdr, 7); + __iowrite32_copy(piobuf + 9, data, dcnt); + ipath_flush_wc(); +} + +/* + * _start packet gets sent twice at start, _done gets sent twice at end + */ +static void ipath_autoneg_send(struct ipath_devdata *dd, int which) +{ + static u32 swapped; + u32 dw, i, hcnt, dcnt, *data; + static u32 hdr[7] = { 0xf002ffff, 0x48ffff, 0x6400abba }; + static u32 madpayload_start[0x40] = { + 0x1810103, 0x1, 0x0, 0x0, 0x2c90000, 0x2c9, 0x0, 0x0, + 0xffffffff, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, + 0x1, 0x1388, 0x15e, 0x1, /* rest 0's */ + }; + static u32 madpayload_done[0x40] = { + 0x1810103, 0x1, 0x0, 0x0, 0x2c90000, 0x2c9, 0x0, 0x0, + 0xffffffff, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, + 0x40000001, 0x1388, 0x15e, /* rest 0's */ + }; + dcnt = sizeof(madpayload_start)/sizeof(madpayload_start[0]); + hcnt = sizeof(hdr)/sizeof(hdr[0]); + if (!swapped) { + /* for maintainability, do it at runtime */ + for (i = 0; i < hcnt; i++) { + dw = (__force u32) cpu_to_be32(hdr[i]); + hdr[i] = dw; + } + for (i = 0; i < dcnt; i++) { + dw = (__force u32) cpu_to_be32(madpayload_start[i]); + madpayload_start[i] = dw; + dw = (__force u32) cpu_to_be32(madpayload_done[i]); + madpayload_done[i] = dw; + } + swapped = 1; + } + + data = which ? madpayload_done : madpayload_start; + ipath_cdbg(PKT, "Sending %s special MADs\n", which?"done":"start"); + + autoneg_send(dd, hdr, dcnt, data); + ipath_read_kreg64(dd, dd->ipath_kregs->kr_scratch); + udelay(2); + autoneg_send(dd, hdr, dcnt, data); + ipath_read_kreg64(dd, dd->ipath_kregs->kr_scratch); + udelay(2); +} + + + +/* + * Do the absolute minimum to cause an IB speed change, and make it + * ready, but don't actually trigger the change. The caller will + * do that when ready (if link is in Polling training state, it will + * happen immediately, otherwise when link next goes down) + * + * This routine should only be used as part of the DDR autonegotation + * code for devices that are not compliant with IB 1.2 (or code that + * fixes things up for same). + * + * When link has gone down, and autoneg enabled, or autoneg has + * failed and we give up until next time we set both speeds, and + * then we want IBTA enabled as well as "use max enabled speed. + */ +static void set_speed_fast(struct ipath_devdata *dd, u32 speed) +{ + dd->ipath_ibcddrctrl &= ~(IBA7220_IBC_SPEED_AUTONEG_MASK | + IBA7220_IBC_IBTA_1_2_MASK | + (IBA7220_IBC_WIDTH_MASK << IBA7220_IBC_WIDTH_SHIFT)); + + if (speed == (IPATH_IB_SDR | IPATH_IB_DDR)) + dd->ipath_ibcddrctrl |= IBA7220_IBC_SPEED_AUTONEG_MASK | + IBA7220_IBC_IBTA_1_2_MASK; + else + dd->ipath_ibcddrctrl |= speed == IPATH_IB_DDR ? + IBA7220_IBC_SPEED_DDR : IBA7220_IBC_SPEED_SDR; + + /* + * Convert from IB-style 1 = 1x, 2 = 4x, 3 = auto + * to chip-centric 0 = 1x, 1 = 4x, 2 = auto + */ + dd->ipath_ibcddrctrl |= (u64)(dd->ipath_link_width_enabled - 1) << + IBA7220_IBC_WIDTH_SHIFT; + ipath_write_kreg(dd, dd->ipath_kregs->kr_ibcddrctrl, + dd->ipath_ibcddrctrl); + ipath_cdbg(VERBOSE, "setup for IB speed (%x) done\n", speed); +} + + +/* + * this routine is only used when we are not talking to another + * IB 1.2-compliant device that we think can do DDR. + * (This includes all existing switch chips as of Oct 2007.) + * 1.2-compliant devices go directly to DDR prior to reaching INIT + */ +static void try_auto_neg(struct ipath_devdata *dd) +{ + /* + * required for older non-IB1.2 DDR switches. Newer + * non-IB-compliant switches don't need it, but so far, + * aren't bothered by it either. "Magic constant" + */ + ipath_write_kreg(dd, IPATH_KREG_OFFSET(IBNCModeCtrl), + 0x3b9dc07); + dd->ipath_flags |= IPATH_IB_AUTONEG_INPROG; + ipath_autoneg_send(dd, 0); + set_speed_fast(dd, IPATH_IB_DDR); + ipath_toggle_rclkrls(dd); + /* 2 msec is minimum length of a poll cycle */ + schedule_delayed_work(&dd->ipath_autoneg_work, + msecs_to_jiffies(2)); +} + + +static int ipath_7220_ib_updown(struct ipath_devdata *dd, int ibup, u64 ibcs) +{ + int ret = 0; + u32 ltstate = ipath_ib_linkstate(dd, ibcs); + + dd->ipath_link_width_active = + ((ibcs >> IBA7220_IBCS_LINKWIDTH_SHIFT) & 1) ? + IB_WIDTH_4X : IB_WIDTH_1X; + dd->ipath_link_speed_active = + ((ibcs >> IBA7220_IBCS_LINKSPEED_SHIFT) & 1) ? + IPATH_IB_DDR : IPATH_IB_SDR; + + if (!ibup) { + /* + * when link goes down we don't want aeq running, so it + * won't't interfere with IBC training, etc., and we need + * to go back to the static SerDes preset values + */ + if (dd->ipath_x1_fix_tries && + ltstate <= INFINIPATH_IBCS_LT_STATE_SLEEPQUIET && + ltstate != INFINIPATH_IBCS_LT_STATE_LINKUP) + dd->ipath_x1_fix_tries = 0; + if (!(dd->ipath_flags & (IPATH_IB_AUTONEG_FAILED | + IPATH_IB_AUTONEG_INPROG))) + set_speed_fast(dd, dd->ipath_link_speed_enabled); + if (!(dd->ipath_flags & IPATH_IB_AUTONEG_INPROG)) { + ipath_cdbg(VERBOSE, "Setting RXEQ defaults\n"); + ipath_sd7220_presets(dd); + } + /* this might better in ipath_sd7220_presets() */ + ipath_set_relock_poll(dd, ibup); + } else { + if (ipath_compat_ddr_negotiate && + !(dd->ipath_flags & (IPATH_IB_AUTONEG_FAILED | + IPATH_IB_AUTONEG_INPROG)) && + dd->ipath_link_speed_active == IPATH_IB_SDR && + (dd->ipath_link_speed_enabled & + (IPATH_IB_DDR | IPATH_IB_SDR)) == + (IPATH_IB_DDR | IPATH_IB_SDR) && + dd->ipath_autoneg_tries < IPATH_AUTONEG_TRIES) { + /* we are SDR, and DDR auto-negotiation enabled */ + ++dd->ipath_autoneg_tries; + ipath_dbg("DDR negotiation try, %u/%u\n", + dd->ipath_autoneg_tries, + IPATH_AUTONEG_TRIES); + try_auto_neg(dd); + ret = 1; /* no other IB status change processing */ + } else if ((dd->ipath_flags & IPATH_IB_AUTONEG_INPROG) + && dd->ipath_link_speed_active == IPATH_IB_SDR) { + ipath_autoneg_send(dd, 1); + set_speed_fast(dd, IPATH_IB_DDR); + udelay(2); + ipath_toggle_rclkrls(dd); + ret = 1; /* no other IB status change processing */ + } else { + if ((dd->ipath_flags & IPATH_IB_AUTONEG_INPROG) && + (dd->ipath_link_speed_active & IPATH_IB_DDR)) { + ipath_dbg("Got to INIT with DDR autoneg\n"); + dd->ipath_flags &= ~(IPATH_IB_AUTONEG_INPROG + | IPATH_IB_AUTONEG_FAILED); + dd->ipath_autoneg_tries = 0; + /* re-enable SDR, for next link down */ + set_speed_fast(dd, + dd->ipath_link_speed_enabled); + wake_up(&dd->ipath_autoneg_wait); + } else if (dd->ipath_flags & IPATH_IB_AUTONEG_FAILED) { + /* + * clear autoneg failure flag, and do setup + * so we'll try next time link goes down and + * back to INIT (possibly connected to different + * device). + */ + ipath_dbg("INIT %sDR after autoneg failure\n", + (dd->ipath_link_speed_active & + IPATH_IB_DDR) ? "D" : "S"); + dd->ipath_flags &= ~IPATH_IB_AUTONEG_FAILED; + dd->ipath_ibcddrctrl |= + IBA7220_IBC_IBTA_1_2_MASK; + ipath_write_kreg(dd, + IPATH_KREG_OFFSET(IBNCModeCtrl), 0); + } + } + /* + * if we are in 1X, and are in autoneg width, it + * could be due to an xgxs problem, so if we haven't + * already tried, try twice to get to 4X; if we + * tried, and couldn't, report it, since it will + * probably not be what is desired. + */ + if ((dd->ipath_link_width_enabled & (IB_WIDTH_1X | + IB_WIDTH_4X)) == (IB_WIDTH_1X | IB_WIDTH_4X) + && dd->ipath_link_width_active == IB_WIDTH_1X + && dd->ipath_x1_fix_tries < 3) { + if (++dd->ipath_x1_fix_tries == 3) + dev_info(&dd->pcidev->dev, + "IB link is in 1X mode\n"); + else { + ipath_cdbg(VERBOSE, "IB 1X in " + "auto-width, try %u to be " + "sure it's really 1X; " + "ltstate %u\n", + dd->ipath_x1_fix_tries, + ltstate); + dd->ipath_f_xgxs_reset(dd); + ret = 1; /* skip other processing */ + } + } + + if (!ret) { + dd->delay_mult = rate_to_delay + [(ibcs >> IBA7220_IBCS_LINKSPEED_SHIFT) & 1] + [(ibcs >> IBA7220_IBCS_LINKWIDTH_SHIFT) & 1]; + + ipath_set_relock_poll(dd, ibup); + } + } + + if (!ret) + ipath_setup_7220_setextled(dd, ipath_ib_linkstate(dd, ibcs), + ltstate); + return ret; +} + + +/* + * Handle the empirically determined mechanism for auto-negotiation + * of DDR speed with switches. + */ +static void autoneg_work(struct work_struct *work) +{ + struct ipath_devdata *dd; + u64 startms; + u32 lastlts, i; + + dd = container_of(work, struct ipath_devdata, + ipath_autoneg_work.work); + + startms = jiffies_to_msecs(jiffies); + + /* + * busy wait for this first part, it should be at most a + * few hundred usec, since we scheduled ourselves for 2msec. + */ + for (i = 0; i < 25; i++) { + lastlts = ipath_ib_linktrstate(dd, dd->ipath_lastibcstat); + if (lastlts == INFINIPATH_IBCS_LT_STATE_POLLQUIET) { + ipath_set_linkstate(dd, IPATH_IB_LINKDOWN_DISABLE); + break; + } + udelay(100); + } + + if (!(dd->ipath_flags & IPATH_IB_AUTONEG_INPROG)) + goto done; /* we got there early or told to stop */ + + /* we expect this to timeout */ + if (wait_event_timeout(dd->ipath_autoneg_wait, + !(dd->ipath_flags & IPATH_IB_AUTONEG_INPROG), + msecs_to_jiffies(90))) + goto done; + + ipath_toggle_rclkrls(dd); + + /* we expect this to timeout */ + if (wait_event_timeout(dd->ipath_autoneg_wait, + !(dd->ipath_flags & IPATH_IB_AUTONEG_INPROG), + msecs_to_jiffies(1700))) + goto done; + + set_speed_fast(dd, IPATH_IB_SDR); + ipath_toggle_rclkrls(dd); + + /* + * wait up to 250 msec for link to train and get to INIT at DDR; + * this should terminate early + */ + wait_event_timeout(dd->ipath_autoneg_wait, + !(dd->ipath_flags & IPATH_IB_AUTONEG_INPROG), + msecs_to_jiffies(250)); +done: + if (dd->ipath_flags & IPATH_IB_AUTONEG_INPROG) { + ipath_dbg("Did not get to DDR INIT (%x) after %Lu msecs\n", + ipath_ib_state(dd, dd->ipath_lastibcstat), + jiffies_to_msecs(jiffies)-startms); + dd->ipath_flags &= ~IPATH_IB_AUTONEG_INPROG; + if (dd->ipath_autoneg_tries == IPATH_AUTONEG_TRIES) { + dd->ipath_flags |= IPATH_IB_AUTONEG_FAILED; + ipath_dbg("Giving up on DDR until next IB " + "link Down\n"); + dd->ipath_autoneg_tries = 0; + } + set_speed_fast(dd, dd->ipath_link_speed_enabled); + } +} + + +/** + * ipath_init_iba7220_funcs - set up the chip-specific function pointers + * @dd: the infinipath device + * + * This is global, and is called directly at init to set up the + * chip-specific function pointers for later use. + */ +void ipath_init_iba7220_funcs(struct ipath_devdata *dd) +{ + dd->ipath_f_intrsetup = ipath_7220_intconfig; + dd->ipath_f_bus = ipath_setup_7220_config; + dd->ipath_f_reset = ipath_setup_7220_reset; + dd->ipath_f_get_boardname = ipath_7220_boardname; + dd->ipath_f_init_hwerrors = ipath_7220_init_hwerrors; + dd->ipath_f_early_init = ipath_7220_early_init; + dd->ipath_f_handle_hwerrors = ipath_7220_handle_hwerrors; + dd->ipath_f_quiet_serdes = ipath_7220_quiet_serdes; + dd->ipath_f_bringup_serdes = ipath_7220_bringup_serdes; + dd->ipath_f_clear_tids = ipath_7220_clear_tids; + dd->ipath_f_put_tid = ipath_7220_put_tid; + dd->ipath_f_cleanup = ipath_setup_7220_cleanup; + dd->ipath_f_setextled = ipath_setup_7220_setextled; + dd->ipath_f_get_base_info = ipath_7220_get_base_info; + dd->ipath_f_free_irq = ipath_7220_free_irq; + dd->ipath_f_tidtemplate = ipath_7220_tidtemplate; + dd->ipath_f_intr_fallback = ipath_7220_intr_fallback; + dd->ipath_f_xgxs_reset = ipath_7220_xgxs_reset; + dd->ipath_f_get_ib_cfg = ipath_7220_get_ib_cfg; + dd->ipath_f_set_ib_cfg = ipath_7220_set_ib_cfg; + dd->ipath_f_config_jint = ipath_7220_config_jint; + dd->ipath_f_config_ports = ipath_7220_config_ports; + dd->ipath_f_read_counters = ipath_7220_read_counters; + dd->ipath_f_get_msgheader = ipath_7220_get_msgheader; + dd->ipath_f_ib_updown = ipath_7220_ib_updown; + + /* initialize chip-specific variables */ + ipath_init_7220_variables(dd); +} |