diff options
Diffstat (limited to 'drivers/infiniband/hw/ipath')
| -rw-r--r-- | drivers/infiniband/hw/ipath/Kconfig | 2 | ||||
| -rw-r--r-- | drivers/infiniband/hw/ipath/Makefile | 5 | ||||
| -rw-r--r-- | drivers/infiniband/hw/ipath/ipath_diag.c | 65 | ||||
| -rw-r--r-- | drivers/infiniband/hw/ipath/ipath_driver.c | 31 | ||||
| -rw-r--r-- | drivers/infiniband/hw/ipath/ipath_iba6110.c | 117 | ||||
| -rw-r--r-- | drivers/infiniband/hw/ipath/ipath_iba6120.c | 8 | ||||
| -rw-r--r-- | drivers/infiniband/hw/ipath/ipath_intr.c | 10 | ||||
| -rw-r--r-- | drivers/infiniband/hw/ipath/ipath_kernel.h | 7 |
8 files changed, 120 insertions, 125 deletions
diff --git a/drivers/infiniband/hw/ipath/Kconfig b/drivers/infiniband/hw/ipath/Kconfig index 574a678e7fd..90c14543677 100644 --- a/drivers/infiniband/hw/ipath/Kconfig +++ b/drivers/infiniband/hw/ipath/Kconfig @@ -1,6 +1,6 @@ config INFINIBAND_IPATH tristate "QLogic InfiniPath Driver" - depends on PCI_MSI && 64BIT && INFINIBAND + depends on (PCI_MSI || HT_IRQ) && 64BIT && INFINIBAND && NET ---help--- This is a driver for QLogic InfiniPath host channel adapters, including InfiniBand verbs support. This driver allows these diff --git a/drivers/infiniband/hw/ipath/Makefile b/drivers/infiniband/hw/ipath/Makefile index 5e29cb0095e..7dc10551cf1 100644 --- a/drivers/infiniband/hw/ipath/Makefile +++ b/drivers/infiniband/hw/ipath/Makefile @@ -10,8 +10,6 @@ ib_ipath-y := \ ipath_eeprom.o \ ipath_file_ops.o \ ipath_fs.o \ - ipath_iba6110.o \ - ipath_iba6120.o \ ipath_init_chip.o \ ipath_intr.o \ ipath_keys.o \ @@ -31,5 +29,8 @@ ib_ipath-y := \ ipath_verbs_mcast.o \ ipath_verbs.o +ib_ipath-$(CONFIG_HT_IRQ) += ipath_iba6110.o +ib_ipath-$(CONFIG_PCI_MSI) += ipath_iba6120.o + ib_ipath-$(CONFIG_X86_64) += ipath_wc_x86_64.o ib_ipath-$(CONFIG_PPC64) += ipath_wc_ppc64.o diff --git a/drivers/infiniband/hw/ipath/ipath_diag.c b/drivers/infiniband/hw/ipath/ipath_diag.c index 29958b6e021..28c087b824c 100644 --- a/drivers/infiniband/hw/ipath/ipath_diag.c +++ b/drivers/infiniband/hw/ipath/ipath_diag.c @@ -67,19 +67,54 @@ static struct file_operations diag_file_ops = { .release = ipath_diag_release }; +static ssize_t ipath_diagpkt_write(struct file *fp, + const char __user *data, + size_t count, loff_t *off); + +static struct file_operations diagpkt_file_ops = { + .owner = THIS_MODULE, + .write = ipath_diagpkt_write, +}; + +static atomic_t diagpkt_count = ATOMIC_INIT(0); +static struct cdev *diagpkt_cdev; +static struct class_device *diagpkt_class_dev; + int ipath_diag_add(struct ipath_devdata *dd) { char name[16]; + int ret = 0; + + if (atomic_inc_return(&diagpkt_count) == 1) { + ret = ipath_cdev_init(IPATH_DIAGPKT_MINOR, + "ipath_diagpkt", &diagpkt_file_ops, + &diagpkt_cdev, &diagpkt_class_dev); + + if (ret) { + ipath_dev_err(dd, "Couldn't create ipath_diagpkt " + "device: %d", ret); + goto done; + } + } snprintf(name, sizeof(name), "ipath_diag%d", dd->ipath_unit); - return ipath_cdev_init(IPATH_DIAG_MINOR_BASE + dd->ipath_unit, name, - &diag_file_ops, &dd->diag_cdev, - &dd->diag_class_dev); + ret = ipath_cdev_init(IPATH_DIAG_MINOR_BASE + dd->ipath_unit, name, + &diag_file_ops, &dd->diag_cdev, + &dd->diag_class_dev); + if (ret) + ipath_dev_err(dd, "Couldn't create %s device: %d", + name, ret); + +done: + return ret; } void ipath_diag_remove(struct ipath_devdata *dd) { + if (atomic_dec_and_test(&diagpkt_count)) + ipath_cdev_cleanup(&diagpkt_cdev, &diagpkt_class_dev); + ipath_cdev_cleanup(&dd->diag_cdev, &dd->diag_class_dev); } @@ -275,30 +310,6 @@ bail: return ret; } -static ssize_t ipath_diagpkt_write(struct file *fp, - const char __user *data, - size_t count, loff_t *off); - -static struct file_operations diagpkt_file_ops = { - .owner = THIS_MODULE, - .write = ipath_diagpkt_write, -}; - -static struct cdev *diagpkt_cdev; -static struct class_device *diagpkt_class_dev; - -int __init ipath_diagpkt_add(void) -{ - return ipath_cdev_init(IPATH_DIAGPKT_MINOR, - "ipath_diagpkt", &diagpkt_file_ops, - &diagpkt_cdev, &diagpkt_class_dev); -} - -void __exit ipath_diagpkt_remove(void) -{ - ipath_cdev_cleanup(&diagpkt_cdev, &diagpkt_class_dev); -} - /** * ipath_diagpkt_write - write an IB packet * @fp: the diag data device file pointer diff --git a/drivers/infiniband/hw/ipath/ipath_driver.c b/drivers/infiniband/hw/ipath/ipath_driver.c index 12cefa658f3..1aeddb48e35 100644 --- a/drivers/infiniband/hw/ipath/ipath_driver.c +++ b/drivers/infiniband/hw/ipath/ipath_driver.c @@ -304,7 +304,7 @@ static int __devinit ipath_init_one(struct pci_dev *pdev, } addr = pci_resource_start(pdev, 0); len = pci_resource_len(pdev, 0); - ipath_cdbg(VERBOSE, "regbase (0) %llx len %d irq %x, vend %x/%x " + ipath_cdbg(VERBOSE, "regbase (0) %llx len %d pdev->irq %d, vend %x/%x " "driver_data %lx\n", addr, len, pdev->irq, ent->vendor, ent->device, ent->driver_data); @@ -390,12 +390,16 @@ static int __devinit ipath_init_one(struct pci_dev *pdev, /* setup the chip-specific functions, as early as possible. */ switch (ent->device) { +#ifdef CONFIG_HT_IRQ case PCI_DEVICE_ID_INFINIPATH_HT: ipath_init_iba6110_funcs(dd); break; +#endif +#ifdef CONFIG_PCI_MSI case PCI_DEVICE_ID_INFINIPATH_PE800: ipath_init_iba6120_funcs(dd); break; +#endif default: ipath_dev_err(dd, "Found unknown QLogic deviceid 0x%x, " "failing\n", ent->device); @@ -467,15 +471,15 @@ static int __devinit ipath_init_one(struct pci_dev *pdev, * check 0 irq after we return from chip-specific bus setup, since * that can affect this due to setup */ - if (!pdev->irq) + if (!dd->ipath_irq) ipath_dev_err(dd, "irq is 0, BIOS error? Interrupts won't " "work\n"); else { - ret = request_irq(pdev->irq, ipath_intr, IRQF_SHARED, + ret = request_irq(dd->ipath_irq, ipath_intr, IRQF_SHARED, IPATH_DRV_NAME, dd); if (ret) { ipath_dev_err(dd, "Couldn't setup irq handler, " - "irq=%u: %d\n", pdev->irq, ret); + "irq=%d: %d\n", dd->ipath_irq, ret); goto bail_iounmap; } } @@ -637,11 +641,10 @@ static void __devexit ipath_remove_one(struct pci_dev *pdev) * free up port 0 (kernel) rcvhdr, egr bufs, and eventually tid bufs * for all versions of the driver, if they were allocated */ - if (pdev->irq) { - ipath_cdbg(VERBOSE, - "unit %u free_irq of irq %x\n", - dd->ipath_unit, pdev->irq); - free_irq(pdev->irq, dd); + if (dd->ipath_irq) { + ipath_cdbg(VERBOSE, "unit %u free irq %d\n", + dd->ipath_unit, dd->ipath_irq); + dd->ipath_f_free_irq(dd); } else ipath_dbg("irq is 0, not doing free_irq " "for unit %u\n", dd->ipath_unit); @@ -2005,18 +2008,8 @@ static int __init infinipath_init(void) goto bail_group; } - ret = ipath_diagpkt_add(); - if (ret < 0) { - printk(KERN_ERR IPATH_DRV_NAME ": Unable to create " - "diag data device: error %d\n", -ret); - goto bail_ipathfs; - } - goto bail; -bail_ipathfs: - ipath_exit_ipathfs(); - bail_group: ipath_driver_remove_group(&ipath_driver.driver); diff --git a/drivers/infiniband/hw/ipath/ipath_iba6110.c b/drivers/infiniband/hw/ipath/ipath_iba6110.c index 9e4e8d4c6e2..e57c7a351cb 100644 --- a/drivers/infiniband/hw/ipath/ipath_iba6110.c +++ b/drivers/infiniband/hw/ipath/ipath_iba6110.c @@ -38,6 +38,7 @@ #include <linux/pci.h> #include <linux/delay.h> +#include <linux/htirq.h> #include "ipath_kernel.h" #include "ipath_registers.h" @@ -913,49 +914,40 @@ static void slave_or_pri_blk(struct ipath_devdata *dd, struct pci_dev *pdev, } } -static int set_int_handler(struct ipath_devdata *dd, struct pci_dev *pdev, - int pos) +static int ipath_ht_intconfig(struct ipath_devdata *dd) { - u32 int_handler_addr_lower; - u32 int_handler_addr_upper; - u64 ihandler; - u32 intvec; + int ret; - /* use indirection register to get the intr handler */ - pci_write_config_byte(pdev, pos + HT_INTR_REG_INDEX, 0x10); - pci_read_config_dword(pdev, pos + 4, &int_handler_addr_lower); - pci_write_config_byte(pdev, pos + HT_INTR_REG_INDEX, 0x11); - pci_read_config_dword(pdev, pos + 4, &int_handler_addr_upper); + if (dd->ipath_intconfig) { + ipath_write_kreg(dd, dd->ipath_kregs->kr_interruptconfig, + dd->ipath_intconfig); /* interrupt address */ + ret = 0; + } else { + ipath_dev_err(dd, "No interrupts enabled, couldn't setup " + "interrupt address\n"); + ret = -EINVAL; + } - ihandler = (u64) int_handler_addr_lower | - ((u64) int_handler_addr_upper << 32); + return ret; +} + +static void ipath_ht_irq_update(struct pci_dev *dev, int irq, + struct ht_irq_msg *msg) +{ + struct ipath_devdata *dd = pci_get_drvdata(dev); + u64 prev_intconfig = dd->ipath_intconfig; + + dd->ipath_intconfig = msg->address_lo; + dd->ipath_intconfig |= ((u64) msg->address_hi) << 32; /* - * kernels with CONFIG_PCI_MSI set the vector in the irq field of - * struct pci_device, so we use that to program the internal - * interrupt register (not config space) with that value. The BIOS - * must still have done the basic MSI setup. - */ - intvec = pdev->irq; - /* - * clear any vector bits there; normally not set but we'll overload - * this for some debug purposes (setting the HTC debug register - * value from software, rather than GPIOs), so it might be set on a - * driver reload. + * If the previous value of dd->ipath_intconfig is zero, we're + * getting configured for the first time, and must not program the + * intconfig register here (it will be programmed later, when the + * hardware is ready). Otherwise, we should. */ - ihandler &= ~0xff0000; - /* x86 vector goes in intrinfo[23:16] */ - ihandler |= intvec << 16; - ipath_cdbg(VERBOSE, "ihandler lower %x, upper %x, intvec %x, " - "interruptconfig %llx\n", int_handler_addr_lower, - int_handler_addr_upper, intvec, - (unsigned long long) ihandler); - - /* can't program yet, so save for interrupt setup */ - dd->ipath_intconfig = ihandler; - /* keep going, so we find link control stuff also */ - - return ihandler != 0; + if (prev_intconfig) + ipath_ht_intconfig(dd); } /** @@ -971,12 +963,19 @@ static int set_int_handler(struct ipath_devdata *dd, struct pci_dev *pdev, static int ipath_setup_ht_config(struct ipath_devdata *dd, struct pci_dev *pdev) { - int pos, ret = 0; - int ihandler = 0; + int pos, ret; + + ret = __ht_create_irq(pdev, 0, ipath_ht_irq_update); + if (ret < 0) { + ipath_dev_err(dd, "Couldn't create interrupt handler: " + "err %d\n", ret); + goto bail; + } + dd->ipath_irq = ret; + ret = 0; /* - * Read the capability info to find the interrupt info, and also - * handle clearing CRC errors in linkctrl register if necessary. We + * Handle clearing CRC errors in linkctrl register if necessary. We * do this early, before we ever enable errors or hardware errors, * mostly to avoid causing the chip to enter freeze mode. */ @@ -1000,17 +999,9 @@ static int ipath_setup_ht_config(struct ipath_devdata *dd, } if (!(cap_type & 0xE0)) slave_or_pri_blk(dd, pdev, pos, cap_type); - else if (cap_type == HT_INTR_DISC_CONFIG) - ihandler = set_int_handler(dd, pdev, pos); } while ((pos = pci_find_next_capability(pdev, pos, PCI_CAP_ID_HT))); - if (!ihandler) { - ipath_dev_err(dd, "Couldn't find interrupt handler in " - "config space\n"); - ret = -ENODEV; - } - bail: return ret; } @@ -1360,25 +1351,6 @@ static void ipath_ht_quiet_serdes(struct ipath_devdata *dd) ipath_write_kreg(dd, dd->ipath_kregs->kr_serdesconfig0, val); } -static int ipath_ht_intconfig(struct ipath_devdata *dd) -{ - int ret; - - if (!dd->ipath_intconfig) { - ipath_dev_err(dd, "No interrupts enabled, couldn't setup " - "interrupt address\n"); - ret = 1; - goto bail; - } - - ipath_write_kreg(dd, dd->ipath_kregs->kr_interruptconfig, - dd->ipath_intconfig); /* interrupt address */ - ret = 0; - -bail: - return ret; -} - /** * ipath_pe_put_tid - write a TID in chip * @dd: the infinipath device @@ -1575,6 +1547,14 @@ static int ipath_ht_get_base_info(struct ipath_portdata *pd, void *kbase) return 0; } +static void ipath_ht_free_irq(struct ipath_devdata *dd) +{ + free_irq(dd->ipath_irq, dd); + ht_destroy_irq(dd->ipath_irq); + dd->ipath_irq = 0; + dd->ipath_intconfig = 0; +} + /** * ipath_init_iba6110_funcs - set up the chip-specific function pointers * @dd: the infinipath device @@ -1598,6 +1578,7 @@ void ipath_init_iba6110_funcs(struct ipath_devdata *dd) dd->ipath_f_cleanup = ipath_setup_ht_cleanup; dd->ipath_f_setextled = ipath_setup_ht_setextled; dd->ipath_f_get_base_info = ipath_ht_get_base_info; + dd->ipath_f_free_irq = ipath_ht_free_irq; /* * initialize chip-specific variables diff --git a/drivers/infiniband/hw/ipath/ipath_iba6120.c b/drivers/infiniband/hw/ipath/ipath_iba6120.c index a72ab9de386..6af89683f71 100644 --- a/drivers/infiniband/hw/ipath/ipath_iba6120.c +++ b/drivers/infiniband/hw/ipath/ipath_iba6120.c @@ -851,6 +851,7 @@ static int ipath_setup_pe_config(struct ipath_devdata *dd, int pos, ret; dd->ipath_msi_lo = 0; /* used as a flag during reset processing */ + dd->ipath_irq = pdev->irq; ret = pci_enable_msi(dd->pcidev); if (ret) ipath_dev_err(dd, "pci_enable_msi failed: %d, " @@ -1323,6 +1324,12 @@ done: return 0; } +static void ipath_pe_free_irq(struct ipath_devdata *dd) +{ + free_irq(dd->ipath_irq, dd); + dd->ipath_irq = 0; +} + /** * ipath_init_iba6120_funcs - set up the chip-specific function pointers * @dd: the infinipath device @@ -1349,6 +1356,7 @@ void ipath_init_iba6120_funcs(struct ipath_devdata *dd) dd->ipath_f_cleanup = ipath_setup_pe_cleanup; dd->ipath_f_setextled = ipath_setup_pe_setextled; dd->ipath_f_get_base_info = ipath_pe_get_base_info; + dd->ipath_f_free_irq = ipath_pe_free_irq; /* initialize chip-specific variables */ dd->ipath_f_tidtemplate = ipath_pe_tidtemplate; diff --git a/drivers/infiniband/hw/ipath/ipath_intr.c b/drivers/infiniband/hw/ipath/ipath_intr.c index d9079ee1203..5652a550d44 100644 --- a/drivers/infiniband/hw/ipath/ipath_intr.c +++ b/drivers/infiniband/hw/ipath/ipath_intr.c @@ -710,14 +710,14 @@ static void ipath_bad_intr(struct ipath_devdata *dd, u32 * unexpectp) * linuxbios development work, and it may happen in * the future again. */ - if (dd->pcidev && dd->pcidev->irq) { + if (dd->pcidev && dd->ipath_irq) { ipath_dev_err(dd, "Now %u unexpected " "interrupts, unregistering " "interrupt handler\n", *unexpectp); - ipath_dbg("free_irq of irq %x\n", - dd->pcidev->irq); - free_irq(dd->pcidev->irq, dd); + ipath_dbg("free_irq of irq %d\n", + dd->ipath_irq); + dd->ipath_f_free_irq(dd); } } if (ipath_read_kreg32(dd, dd->ipath_kregs->kr_intmask)) { @@ -753,7 +753,7 @@ static void ipath_bad_regread(struct ipath_devdata *dd) if (allbits == 2) { ipath_dev_err(dd, "Still bad interrupt status, " "unregistering interrupt\n"); - free_irq(dd->pcidev->irq, dd); + dd->ipath_f_free_irq(dd); } else if (allbits > 2) { if ((allbits % 10000) == 0) printk("."); diff --git a/drivers/infiniband/hw/ipath/ipath_kernel.h b/drivers/infiniband/hw/ipath/ipath_kernel.h index 7c436697d0e..986b2125b8f 100644 --- a/drivers/infiniband/hw/ipath/ipath_kernel.h +++ b/drivers/infiniband/hw/ipath/ipath_kernel.h @@ -213,6 +213,8 @@ struct ipath_devdata { void (*ipath_f_setextled)(struct ipath_devdata *, u64, u64); /* fill out chip-specific fields */ int (*ipath_f_get_base_info)(struct ipath_portdata *, void *); + /* free irq */ + void (*ipath_f_free_irq)(struct ipath_devdata *); struct ipath_ibdev *verbs_dev; struct timer_list verbs_timer; /* total dwords sent (summed from counter) */ @@ -328,6 +330,8 @@ struct ipath_devdata { /* so we can rewrite it after a chip reset */ u32 ipath_pcibar1; + /* interrupt number */ + int ipath_irq; /* HT/PCI Vendor ID (here for NodeInfo) */ u16 ipath_vendorid; /* HT/PCI Device ID (here for NodeInfo) */ @@ -869,9 +873,6 @@ int ipath_device_create_group(struct device *, struct ipath_devdata *); void ipath_device_remove_group(struct device *, struct ipath_devdata *); int ipath_expose_reset(struct device *); -int ipath_diagpkt_add(void); -void ipath_diagpkt_remove(void); - int ipath_init_ipathfs(void); void ipath_exit_ipathfs(void); int ipathfs_add_device(struct ipath_devdata *); |