diff options
Diffstat (limited to 'drivers/input/misc')
| -rw-r--r-- | drivers/input/misc/Kconfig | 42 | ||||
| -rw-r--r-- | drivers/input/misc/Makefile | 3 | ||||
| -rw-r--r-- | drivers/input/misc/cma3000_d0x.c | 398 | ||||
| -rw-r--r-- | drivers/input/misc/cma3000_d0x.h | 42 | ||||
| -rw-r--r-- | drivers/input/misc/cma3000_d0x_i2c.c | 143 | ||||
| -rw-r--r-- | drivers/input/misc/pcf8574_keypad.c | 19 | ||||
| -rw-r--r-- | drivers/input/misc/uinput.c | 8 | ||||
| -rw-r--r-- | drivers/input/misc/winbond-cir.c | 1608 |
8 files changed, 630 insertions, 1633 deletions
diff --git a/drivers/input/misc/Kconfig b/drivers/input/misc/Kconfig index b99b8cbde02..b0c6772851a 100644 --- a/drivers/input/misc/Kconfig +++ b/drivers/input/misc/Kconfig @@ -294,24 +294,6 @@ config INPUT_SGI_BTNS To compile this driver as a module, choose M here: the module will be called sgi_btns. -config INPUT_WINBOND_CIR - tristate "Winbond IR remote control" - depends on X86 && PNP - select NEW_LEDS - select LEDS_CLASS - select LEDS_TRIGGERS - select BITREVERSE - help - Say Y here if you want to use the IR remote functionality found - in some Winbond SuperI/O chips. Currently only the WPCD376I - chip is supported (included in some Intel Media series motherboards). - - IR Receive and wake-on-IR from suspend and power-off is currently - supported. - - To compile this driver as a module, choose M here: the module will be - called winbond_cir. - config HP_SDC_RTC tristate "HP SDC Real Time Clock" depends on (GSC || HP300) && SERIO @@ -448,4 +430,28 @@ config INPUT_ADXL34X_SPI To compile this driver as a module, choose M here: the module will be called adxl34x-spi. +config INPUT_CMA3000 + tristate "VTI CMA3000 Tri-axis accelerometer" + help + Say Y here if you want to use VTI CMA3000_D0x Accelerometer + driver + + This driver currently only supports I2C interface to the + controller. Also select the I2C method. + + If unsure, say N + + To compile this driver as a module, choose M here: the + module will be called cma3000_d0x. + +config INPUT_CMA3000_I2C + tristate "Support I2C bus connection" + depends on INPUT_CMA3000 && I2C + help + Say Y here if you want to use VTI CMA3000_D0x Accelerometer + through I2C interface. + + To compile this driver as a module, choose M here: the + module will be called cma3000_d0x_i2c. + endif diff --git a/drivers/input/misc/Makefile b/drivers/input/misc/Makefile index 1fe1f6c8b73..9b4797112c9 100644 --- a/drivers/input/misc/Makefile +++ b/drivers/input/misc/Makefile @@ -18,6 +18,8 @@ obj-$(CONFIG_INPUT_ATI_REMOTE2) += ati_remote2.o obj-$(CONFIG_INPUT_ATLAS_BTNS) += atlas_btns.o obj-$(CONFIG_INPUT_BFIN_ROTARY) += bfin_rotary.o obj-$(CONFIG_INPUT_CM109) += cm109.o +obj-$(CONFIG_INPUT_CMA3000) += cma3000_d0x.o +obj-$(CONFIG_INPUT_CMA3000_I2C) += cma3000_d0x_i2c.o obj-$(CONFIG_INPUT_COBALT_BTNS) += cobalt_btns.o obj-$(CONFIG_INPUT_DM355EVM) += dm355evm_keys.o obj-$(CONFIG_HP_SDC_RTC) += hp_sdc_rtc.o @@ -38,7 +40,6 @@ obj-$(CONFIG_INPUT_SPARCSPKR) += sparcspkr.o obj-$(CONFIG_INPUT_TWL4030_PWRBUTTON) += twl4030-pwrbutton.o obj-$(CONFIG_INPUT_TWL4030_VIBRA) += twl4030-vibra.o obj-$(CONFIG_INPUT_UINPUT) += uinput.o -obj-$(CONFIG_INPUT_WINBOND_CIR) += winbond-cir.o obj-$(CONFIG_INPUT_WISTRON_BTNS) += wistron_btns.o obj-$(CONFIG_INPUT_WM831X_ON) += wm831x-on.o obj-$(CONFIG_INPUT_YEALINK) += yealink.o diff --git a/drivers/input/misc/cma3000_d0x.c b/drivers/input/misc/cma3000_d0x.c new file mode 100644 index 00000000000..1633b634226 --- /dev/null +++ b/drivers/input/misc/cma3000_d0x.c @@ -0,0 +1,398 @@ +/* + * VTI CMA3000_D0x Accelerometer driver + * + * Copyright (C) 2010 Texas Instruments + * Author: Hemanth V <hemanthv@ti.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include <linux/types.h> +#include <linux/interrupt.h> +#include <linux/delay.h> +#include <linux/slab.h> +#include <linux/input.h> +#include <linux/input/cma3000.h> + +#include "cma3000_d0x.h" + +#define CMA3000_WHOAMI 0x00 +#define CMA3000_REVID 0x01 +#define CMA3000_CTRL 0x02 +#define CMA3000_STATUS 0x03 +#define CMA3000_RSTR 0x04 +#define CMA3000_INTSTATUS 0x05 +#define CMA3000_DOUTX 0x06 +#define CMA3000_DOUTY 0x07 +#define CMA3000_DOUTZ 0x08 +#define CMA3000_MDTHR 0x09 +#define CMA3000_MDFFTMR 0x0A +#define CMA3000_FFTHR 0x0B + +#define CMA3000_RANGE2G (1 << 7) +#define CMA3000_RANGE8G (0 << 7) +#define CMA3000_BUSI2C (0 << 4) +#define CMA3000_MODEMASK (7 << 1) +#define CMA3000_GRANGEMASK (1 << 7) + +#define CMA3000_STATUS_PERR 1 +#define CMA3000_INTSTATUS_FFDET (1 << 2) + +/* Settling time delay in ms */ +#define CMA3000_SETDELAY 30 + +/* Delay for clearing interrupt in us */ +#define CMA3000_INTDELAY 44 + + +/* + * Bit weights in mg for bit 0, other bits need + * multipy factor 2^n. Eight bit is the sign bit. + */ +#define BIT_TO_2G 18 +#define BIT_TO_8G 71 + +struct cma3000_accl_data { + const struct cma3000_bus_ops *bus_ops; + const struct cma3000_platform_data *pdata; + + struct device *dev; + struct input_dev *input_dev; + + int bit_to_mg; + int irq; + + int g_range; + u8 mode; + + struct mutex mutex; + bool opened; + bool suspended; +}; + +#define CMA3000_READ(data, reg, msg) \ + (data->bus_ops->read(data->dev, reg, msg)) +#define CMA3000_SET(data, reg, val, msg) \ + ((data)->bus_ops->write(data->dev, reg, val, msg)) + +/* + * Conversion for each of the eight modes to g, depending + * on G range i.e 2G or 8G. Some modes always operate in + * 8G. + */ + +static int mode_to_mg[8][2] = { + { 0, 0 }, + { BIT_TO_8G, BIT_TO_2G }, + { BIT_TO_8G, BIT_TO_2G }, + { BIT_TO_8G, BIT_TO_8G }, + { BIT_TO_8G, BIT_TO_8G }, + { BIT_TO_8G, BIT_TO_2G }, + { BIT_TO_8G, BIT_TO_2G }, + { 0, 0}, +}; + +static void decode_mg(struct cma3000_accl_data *data, int *datax, + int *datay, int *dataz) +{ + /* Data in 2's complement, convert to mg */ + *datax = ((s8)*datax) * data->bit_to_mg; + *datay = ((s8)*datay) * data->bit_to_mg; + *dataz = ((s8)*dataz) * data->bit_to_mg; +} + +static irqreturn_t cma3000_thread_irq(int irq, void *dev_id) +{ + struct cma3000_accl_data *data = dev_id; + int datax, datay, dataz; + u8 ctrl, mode, range, intr_status; + + intr_status = CMA3000_READ(data, CMA3000_INTSTATUS, "interrupt status"); + if (intr_status < 0) + return IRQ_NONE; + + /* Check if free fall is detected, report immediately */ + if (intr_status & CMA3000_INTSTATUS_FFDET) { + input_report_abs(data->input_dev, ABS_MISC, 1); + input_sync(data->input_dev); + } else { + input_report_abs(data->input_dev, ABS_MISC, 0); + } + + datax = CMA3000_READ(data, CMA3000_DOUTX, "X"); + datay = CMA3000_READ(data, CMA3000_DOUTY, "Y"); + dataz = CMA3000_READ(data, CMA3000_DOUTZ, "Z"); + + ctrl = CMA3000_READ(data, CMA3000_CTRL, "ctrl"); + mode = (ctrl & CMA3000_MODEMASK) >> 1; + range = (ctrl & CMA3000_GRANGEMASK) >> 7; + + data->bit_to_mg = mode_to_mg[mode][range]; + + /* Interrupt not for this device */ + if (data->bit_to_mg == 0) + return IRQ_NONE; + + /* Decode register values to milli g */ + decode_mg(data, &datax, &datay, &dataz); + + input_report_abs(data->input_dev, ABS_X, datax); + input_report_abs(data->input_dev, ABS_Y, datay); + input_report_abs(data->input_dev, ABS_Z, dataz); + input_sync(data->input_dev); + + return IRQ_HANDLED; +} + +static int cma3000_reset(struct cma3000_accl_data *data) +{ + int val; + + /* Reset sequence */ + CMA3000_SET(data, CMA3000_RSTR, 0x02, "Reset"); + CMA3000_SET(data, CMA3000_RSTR, 0x0A, "Reset"); + CMA3000_SET(data, CMA3000_RSTR, 0x04, "Reset"); + + /* Settling time delay */ + mdelay(10); + + val = CMA3000_READ(data, CMA3000_STATUS, "Status"); + if (val < 0) { + dev_err(data->dev, "Reset failed\n"); + return val; + } + + if (val & CMA3000_STATUS_PERR) { + dev_err(data->dev, "Parity Error\n"); + return -EIO; + } + + return 0; +} + +static int cma3000_poweron(struct cma3000_accl_data *data) +{ + const struct cma3000_platform_data *pdata = data->pdata; + u8 ctrl = 0; + int ret; + + if (data->g_range == CMARANGE_2G) { + ctrl = (data->mode << 1) | CMA3000_RANGE2G; + } else if (data->g_range == CMARANGE_8G) { + ctrl = (data->mode << 1) | CMA3000_RANGE8G; + } else { + dev_info(data->dev, + "Invalid G range specified, assuming 8G\n"); + ctrl = (data->mode << 1) | CMA3000_RANGE8G; + } + + ctrl |= data->bus_ops->ctrl_mod; + + CMA3000_SET(data, CMA3000_MDTHR, pdata->mdthr, + "Motion Detect Threshold"); + CMA3000_SET(data, CMA3000_MDFFTMR, pdata->mdfftmr, + "Time register"); + CMA3000_SET(data, CMA3000_FFTHR, pdata->ffthr, + "Free fall threshold"); + ret = CMA3000_SET(data, CMA3000_CTRL, ctrl, "Mode setting"); + if (ret < 0) + return -EIO; + + msleep(CMA3000_SETDELAY); + + return 0; +} + +static int cma3000_poweroff(struct cma3000_accl_data *data) +{ + int ret; + + ret = CMA3000_SET(data, CMA3000_CTRL, CMAMODE_POFF, "Mode setting"); + msleep(CMA3000_SETDELAY); + + return ret; +} + +static int cma3000_open(struct input_dev *input_dev) +{ + struct cma3000_accl_data *data = input_get_drvdata(input_dev); + + mutex_lock(&data->mutex); + + if (!data->suspended) + cma3000_poweron(data); + + data->opened = true; + + mutex_unlock(&data->mutex); + + return 0; +} + +static void cma3000_close(struct input_dev *input_dev) +{ + struct cma3000_accl_data *data = input_get_drvdata(input_dev); + + mutex_lock(&data->mutex); + + if (!data->suspended) + cma3000_poweroff(data); + + data->opened = false; + + mutex_unlock(&data->mutex); +} + +void cma3000_suspend(struct cma3000_accl_data *data) +{ + mutex_lock(&data->mutex); + + if (!data->suspended && data->opened) + cma3000_poweroff(data); + + data->suspended = true; + + mutex_unlock(&data->mutex); +} +EXPORT_SYMBOL(cma3000_suspend); + + +void cma3000_resume(struct cma3000_accl_data *data) +{ + mutex_lock(&data->mutex); + + if (data->suspended && data->opened) + cma3000_poweron(data); + + data->suspended = false; + + mutex_unlock(&data->mutex); +} +EXPORT_SYMBOL(cma3000_resume); + +struct cma3000_accl_data *cma3000_init(struct device *dev, int irq, + const struct cma3000_bus_ops *bops) +{ + const struct cma3000_platform_data *pdata = dev->platform_data; + struct cma3000_accl_data *data; + struct input_dev *input_dev; + int rev; + int error; + + if (!pdata) { + dev_err(dev, "platform data not found\n"); + error = -EINVAL; + goto err_out; + } + + + /* if no IRQ return error */ + if (irq == 0) { + error = -EINVAL; + goto err_out; + } + + data = kzalloc(sizeof(struct cma3000_accl_data), GFP_KERNEL); + input_dev = input_allocate_device(); + if (!data || !input_dev) { + error = -ENOMEM; + goto err_free_mem; + } + + data->dev = dev; + data->input_dev = input_dev; + data->bus_ops = bops; + data->pdata = pdata; + data->irq = irq; + mutex_init(&data->mutex); + + data->mode = pdata->mode; + if (data->mode < CMAMODE_DEFAULT || data->mode > CMAMODE_POFF) { + data->mode = CMAMODE_MOTDET; + dev_warn(dev, + "Invalid mode specified, assuming Motion Detect\n"); + } + + data->g_range = pdata->g_range; + if (data->g_range != CMARANGE_2G && data->g_range != CMARANGE_8G) { + dev_info(dev, + "Invalid G range specified, assuming 8G\n"); + data->g_range = CMARANGE_8G; + } + + input_dev->name = "cma3000-accelerometer"; + input_dev->id.bustype = bops->bustype; + input_dev->open = cma3000_open; + input_dev->close = cma3000_close; + + __set_bit(EV_ABS, input_dev->evbit); + + input_set_abs_params(input_dev, ABS_X, + -data->g_range, data->g_range, pdata->fuzz_x, 0); + input_set_abs_params(input_dev, ABS_Y, + -data->g_range, data->g_range, pdata->fuzz_y, 0); + input_set_abs_params(input_dev, ABS_Z, + -data->g_range, data->g_range, pdata->fuzz_z, 0); + input_set_abs_params(input_dev, ABS_MISC, 0, 1, 0, 0); + + input_set_drvdata(input_dev, data); + + error = cma3000_reset(data); + if (error) + goto err_free_mem; + + rev = CMA3000_READ(data, CMA3000_REVID, "Revid"); + if (rev < 0) { + error = rev; + goto err_free_mem; + } + + pr_info("CMA3000 Accelerometer: Revision %x\n", rev); + + error = request_threaded_irq(irq, NULL, cma3000_thread_irq, + pdata->irqflags | IRQF_ONESHOT, + "cma3000_d0x", data); + if (error) { + dev_err(dev, "request_threaded_irq failed\n"); + goto err_free_mem; + } + + error = input_register_device(data->input_dev); + if (error) { + dev_err(dev, "Unable to register input device\n"); + goto err_free_irq; + } + + return data; + +err_free_irq: + free_irq(irq, data); +err_free_mem: + input_free_device(input_dev); + kfree(data); +err_out: + return ERR_PTR(error); +} +EXPORT_SYMBOL(cma3000_init); + +void cma3000_exit(struct cma3000_accl_data *data) +{ + free_irq(data->irq, data); + input_unregister_device(data->input_dev); + kfree(data); +} +EXPORT_SYMBOL(cma3000_exit); + +MODULE_DESCRIPTION("CMA3000-D0x Accelerometer Driver"); +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Hemanth V <hemanthv@ti.com>"); diff --git a/drivers/input/misc/cma3000_d0x.h b/drivers/input/misc/cma3000_d0x.h new file mode 100644 index 00000000000..2304ce306e1 --- /dev/null +++ b/drivers/input/misc/cma3000_d0x.h @@ -0,0 +1,42 @@ +/* + * VTI CMA3000_D0x Accelerometer driver + * + * Copyright (C) 2010 Texas Instruments + * Author: Hemanth V <hemanthv@ti.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#ifndef _INPUT_CMA3000_H +#define _INPUT_CMA3000_H + +#include <linux/types.h> +#include <linux/input.h> + +struct device; +struct cma3000_accl_data; + +struct cma3000_bus_ops { + u16 bustype; + u8 ctrl_mod; + int (*read)(struct device *, u8, char *); + int (*write)(struct device *, u8, u8, char *); +}; + +struct cma3000_accl_data *cma3000_init(struct device *dev, int irq, + const struct cma3000_bus_ops *bops); +void cma3000_exit(struct cma3000_accl_data *); +void cma3000_suspend(struct cma3000_accl_data *); +void cma3000_resume(struct cma3000_accl_data *); + +#endif diff --git a/drivers/input/misc/cma3000_d0x_i2c.c b/drivers/input/misc/cma3000_d0x_i2c.c new file mode 100644 index 00000000000..d100cc5c578 --- /dev/null +++ b/drivers/input/misc/cma3000_d0x_i2c.c @@ -0,0 +1,143 @@ +/* + * Implements I2C interface for VTI CMA300_D0x Accelerometer driver + * + * Copyright (C) 2010 Texas Instruments + * Author: Hemanth V <hemanthv@ti.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include <linux/module.h> +#include <linux/i2c.h> +#include <linux/input/cma3000.h> +#include "cma3000_d0x.h" + +static int cma3000_i2c_set(struct device *dev, + u8 reg, u8 val, char *msg) +{ + struct i2c_client *client = to_i2c_client(dev); + int ret; + + ret = i2c_smbus_write_byte_data(client, reg, val); + if (ret < 0) + dev_err(&client->dev, + "%s failed (%s, %d)\n", __func__, msg, ret); + return ret; +} + +static int cma3000_i2c_read(struct device *dev, u8 reg, char *msg) +{ + struct i2c_client *client = to_i2c_client(dev); + int ret; + + ret = i2c_smbus_read_byte_data(client, reg); + if (ret < 0) + dev_err(&client->dev, + "%s failed (%s, %d)\n", __func__, msg, ret); + return ret; +} + +static const struct cma3000_bus_ops cma3000_i2c_bops = { + .bustype = BUS_I2C, +#define CMA3000_BUSI2C (0 << 4) + .ctrl_mod = CMA3000_BUSI2C, + .read = cma3000_i2c_read, + .write = cma3000_i2c_set, +}; + +static int __devinit cma3000_i2c_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct cma3000_accl_data *data; + + data = cma3000_init(&client->dev, client->irq, &cma3000_i2c_bops); + if (IS_ERR(data)) + return PTR_ERR(data); + + i2c_set_clientdata(client, data); + + return 0; +} + +static int __devexit cma3000_i2c_remove(struct i2c_client *client) +{ + struct cma3000_accl_data *data = i2c_get_clientdata(client); + + cma3000_exit(data); + + return 0; +} + +#ifdef CONFIG_PM +static int cma3000_i2c_suspend(struct device *dev) +{ + struct i2c_client *client = to_i2c_client(dev); + struct cma3000_accl_data *data = i2c_get_clientdata(client); + + cma3000_suspend(data); + + return 0; +} + +static int cma3000_i2c_resume(struct device *dev) +{ + struct i2c_client *client = to_i2c_client(dev); + struct cma3000_accl_data *data = i2c_get_clientdata(client); + + cma3000_resume(data); + + return 0; +} + +static const struct dev_pm_ops cma3000_i2c_pm_ops = { + .suspend = cma3000_i2c_suspend, + .resume = cma3000_i2c_resume, +}; +#endif + +static const struct i2c_device_id cma3000_i2c_id[] = { + { "cma3000_d01", 0 }, + { }, +}; + +MODULE_DEVICE_TABLE(i2c, cma3000_i2c_id); + +static struct i2c_driver cma3000_i2c_driver = { + .probe = cma3000_i2c_probe, + .remove = __devexit_p(cma3000_i2c_remove), + .id_table = cma3000_i2c_id, + .driver = { + .name = "cma3000_i2c_accl", + .owner = THIS_MODULE, +#ifdef CONFIG_PM + .pm = &cma3000_i2c_pm_ops, +#endif + }, +}; + +static int __init cma3000_i2c_init(void) +{ + return i2c_add_driver(&cma3000_i2c_driver); +} + +static void __exit cma3000_i2c_exit(void) +{ + i2c_del_driver(&cma3000_i2c_driver); +} + +module_init(cma3000_i2c_init); +module_exit(cma3000_i2c_exit); + +MODULE_DESCRIPTION("CMA3000-D0x Accelerometer I2C Driver"); +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Hemanth V <hemanthv@ti.com>"); diff --git a/drivers/input/misc/pcf8574_keypad.c b/drivers/input/misc/pcf8574_keypad.c index d1583aea172..08be1a35595 100644 --- a/drivers/input/misc/pcf8574_keypad.c +++ b/drivers/input/misc/pcf8574_keypad.c @@ -169,19 +169,29 @@ static int __devexit pcf8574_kp_remove(struct i2c_client *client) } #ifdef CONFIG_PM -static int pcf8574_kp_resume(struct i2c_client *client) +static int pcf8574_kp_resume(struct device *dev) { + struct i2c_client *client = to_i2c_client(dev); + enable_irq(client->irq); return 0; } -static int pcf8574_kp_suspend(struct i2c_client *client, pm_message_t mesg) +static int pcf8574_kp_suspend(struct device *dev) { + struct i2c_client *client = to_i2c_client(dev); + disable_irq(client->irq); return 0; } + +static const struct dev_pm_ops pcf8574_kp_pm_ops = { + .suspend = pcf8574_kp_suspend, + .resume = pcf8574_kp_resume, +}; + #else # define pcf8574_kp_resume NULL # define pcf8574_kp_suspend NULL @@ -197,11 +207,12 @@ static struct i2c_driver pcf8574_kp_driver = { .driver = { .name = DRV_NAME, .owner = THIS_MODULE, +#ifdef CONFIG_PM + .pm = &pcf8574_kp_pm_ops, +#endif }, .probe = pcf8574_kp_probe, .remove = __devexit_p(pcf8574_kp_remove), - .suspend = pcf8574_kp_suspend, - .resume = pcf8574_kp_resume, .id_table = pcf8574_kp_id, }; diff --git a/drivers/input/misc/uinput.c b/drivers/input/misc/uinput.c index b9410784e6a..82542a1c109 100644 --- a/drivers/input/misc/uinput.c +++ b/drivers/input/misc/uinput.c @@ -37,6 +37,7 @@ #include <linux/fs.h> #include <linux/miscdevice.h> #include <linux/uinput.h> +#include <linux/input/mt.h> #include "../input-compat.h" static int uinput_dev_event(struct input_dev *dev, unsigned int type, unsigned int code, int value) @@ -406,8 +407,7 @@ static int uinput_setup_device(struct uinput_device *udev, const char __user *bu goto exit; if (test_bit(ABS_MT_SLOT, dev->absbit)) { int nslot = input_abs_get_max(dev, ABS_MT_SLOT) + 1; - input_mt_create_slots(dev, nslot); - input_set_events_per_packet(dev, 6 * nslot); + input_mt_init_slots(dev, nslot); } else if (test_bit(ABS_MT_POSITION_X, dev->absbit)) { input_set_events_per_packet(dev, 60); } @@ -680,6 +680,10 @@ static long uinput_ioctl_handler(struct file *file, unsigned int cmd, retval = uinput_set_bit(arg, swbit, SW_MAX); break; + case UI_SET_PROPBIT: + retval = uinput_set_bit(arg, propbit, INPUT_PROP_MAX); + break; + case UI_SET_PHYS: if (udev->state == UIST_CREATED) { retval = -EINVAL; diff --git a/drivers/input/misc/winbond-cir.c b/drivers/input/misc/winbond-cir.c deleted file mode 100644 index 64f1de7960c..00000000000 --- a/drivers/input/misc/winbond-cir.c +++ /dev/null @@ -1,1608 +0,0 @@ -/* - * winbond-cir.c - Driver for the Consumer IR functionality of Winbond - * SuperI/O chips. - * - * Currently supports the Winbond WPCD376i chip (PNP id WEC1022), but - * could probably support others (Winbond WEC102X, NatSemi, etc) - * with minor modifications. - * - * Original Author: David Härdeman <david@hardeman.nu> - * Copyright (C) 2009 David Härdeman <david@hardeman.nu> - * - * Dedicated to Matilda, my newborn daughter, without whose loving attention - * this driver would have been finished in half the time and with a fraction - * of the bugs. - * - * Written using: - * o Winbond WPCD376I datasheet helpfully provided by Jesse Barnes at Intel - * o NatSemi PC87338/PC97338 datasheet (for the serial port stuff) - * o DSDT dumps - * - * Supported features: - * o RC6 - * o Wake-On-CIR functionality - * - * To do: - * o Test NEC and RC5 - * - * Left as an exercise for the reader: - * o Learning (I have neither the hardware, nor the need) - * o IR Transmit (ibid) - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. - */ - -#include <linux/module.h> -#include <linux/pnp.h> -#include <linux/interrupt.h> -#include <linux/timer.h> -#include <linux/input.h> -#include <linux/leds.h> -#include <linux/list.h> -#include <linux/spinlock.h> -#include <linux/pci_ids.h> -#include <linux/io.h> -#include <linux/bitrev.h> -#include <linux/bitops.h> -#include <linux/slab.h> - -#define DRVNAME "winbond-cir" - -/* CEIR Wake-Up Registers, relative to data->wbase */ -#define WBCIR_REG_WCEIR_CTL 0x03 /* CEIR Receiver Control */ -#define WBCIR_REG_WCEIR_STS 0x04 /* CEIR Receiver Status */ -#define WBCIR_REG_WCEIR_EV_EN 0x05 /* CEIR Receiver Event Enable */ -#define WBCIR_REG_WCEIR_CNTL 0x06 /* CEIR Receiver Counter Low */ -#define WBCIR_REG_WCEIR_CNTH 0x07 /* CEIR Receiver Counter High */ -#define WBCIR_REG_WCEIR_INDEX 0x08 /* CEIR Receiver Index */ -#define WBCIR_REG_WCEIR_DATA 0x09 /* CEIR Receiver Data */ -#define WBCIR_REG_WCEIR_CSL 0x0A /* CEIR Re. Compare Strlen */ -#define WBCIR_REG_WCEIR_CFG1 0x0B /* CEIR Re. Configuration 1 */ -#define WBCIR_REG_WCEIR_CFG2 0x0C /* CEIR Re. Configuration 2 */ - -/* CEIR Enhanced Functionality Registers, relative to data->ebase */ -#define WBCIR_REG_ECEIR_CTS 0x00 /* Enhanced IR Control Status */ -#define WBCIR_REG_ECEIR_CCTL 0x01 /* Infrared Counter Control */ -#define WBCIR_REG_ECEIR_CNT_LO 0x02 /* Infrared Counter LSB */ -#define WBCIR_REG_ECEIR_CNT_HI 0x03 /* Infrared Counter MSB */ -#define WBCIR_REG_ECEIR_IREM 0x04 /* Infrared Emitter Status */ - -/* SP3 Banked Registers, relative to data->sbase */ -#define WBCIR_REG_SP3_BSR 0x03 /* Bank Select, all banks */ - /* Bank 0 */ -#define WBCIR_REG_SP3_RXDATA 0x00 /* FIFO RX data (r) */ -#define WBCIR_REG_SP3_TXDATA 0x00 /* FIFO TX data (w) */ -#define WBCIR_REG_SP3_IER 0x01 /* Interrupt Enable */ -#define WBCIR_REG_SP3_EIR 0x02 /* Event Identification (r) */ -#define WBCIR_REG_SP3_FCR 0x02 /* FIFO Control (w) */ -#define WBCIR_REG_SP3_MCR 0x04 /* Mode Control */ -#define WBCIR_REG_SP3_LSR 0x05 /* Link Status */ -#define WBCIR_REG_SP3_MSR 0x06 /* Modem Status */ -#define WBCIR_REG_SP3_ASCR 0x07 /* Aux Status and Control */ - /* Bank 2 */ -#define WBCIR_REG_SP3_BGDL 0x00 /* Baud Divisor LSB */ -#define WBCIR_REG_SP3_BGDH 0x01 /* Baud Divisor MSB */ -#define WBCIR_REG_SP3_EXCR1 0x02 /* Extended Control 1 */ -#define WBCIR_REG_SP3_EXCR2 0x04 /* Extended Control 2 */ -#define WBCIR_REG_SP3_TXFLV 0x06 /* TX FIFO Level */ -#define WBCIR_REG_SP3_RXFLV 0x07 /* RX FIFO Level */ - /* Bank 3 */ -#define WBCIR_REG_SP3_MRID 0x00 /* Module Identification */ -#define WBCIR_REG_SP3_SH_LCR 0x01 /* LCR Shadow */ -#define WBCIR_REG_SP3_SH_FCR 0x02 /* FCR Shadow */ - /* Bank 4 */ -#define WBCIR_REG_SP3_IRCR1 0x02 /* Infrared Control 1 */ - /* Bank 5 */ -#define WBCIR_REG_SP3_IRCR2 0x04 /* Infrared Control 2 */ - /* Bank 6 */ -#define WBCIR_REG_SP3_IRCR3 0x00 /* Infrared Control 3 */ -#define WBCIR_REG_SP3_SIR_PW 0x02 /* SIR Pulse Width */ - /* Bank 7 */ -#define WBCIR_REG_SP3_IRRXDC 0x00 /* IR RX Demod Control */ -#define WBCIR_REG_SP3_IRTXMC 0x01 /* IR TX Mod Control */ -#define WBCIR_REG_SP3_RCCFG 0x02 /* CEIR Config */ -#define WBCIR_REG_SP3_IRCFG1 0x04 /* Infrared Config 1 */ -#define WBCIR_REG_SP3_IRCFG4 0x07 /* Infrared Config 4 */ - -/* - * Magic values follow - */ - -/* No interrupts for WBCIR_REG_SP3_IER and WBCIR_REG_SP3_EIR */ -#define WBCIR_IRQ_NONE 0x00 -/* RX data bit for WBCIR_REG_SP3_IER and WBCIR_REG_SP3_EIR */ -#define WBCIR_IRQ_RX 0x01 -/* Over/Under-flow bit for WBCIR_REG_SP3_IER and WBCIR_REG_SP3_EIR */ -#define WBCIR_IRQ_ERR 0x04 -/* Led enable/disable bit for WBCIR_REG_ECEIR_CTS */ -#define WBCIR_LED_ENABLE 0x80 -/* RX data available bit for WBCIR_REG_SP3_LSR */ -#define WBCIR_RX_AVAIL 0x01 -/* RX disable bit for WBCIR_REG_SP3_ASCR */ -#define WBCIR_RX_DISABLE 0x20 -/* Extended mode enable bit for WBCIR_REG_SP3_EXCR1 */ -#define WBCIR_EXT_ENABLE 0x01 -/* Select compare register in WBCIR_REG_WCEIR_INDEX (bits 5 & 6) */ -#define WBCIR_REGSEL_COMPARE 0x10 -/* Select mask register in WBCIR_REG_WCEIR_INDEX (bits 5 & 6) */ -#define WBCIR_REGSEL_MASK 0x20 -/* Starting address of selected register in WBCIR_REG_WCEIR_INDEX */ -#define WBCIR_REG_ADDR0 0x00 - -/* Valid banks for the SP3 UART */ -enum wbcir_bank { - WBCIR_BANK_0 = 0x00, - WBCIR_BANK_1 = 0x80, - WBCIR_BANK_2 = 0xE0, - WBCIR_BANK_3 = 0xE4, - WBCIR_BANK_4 = 0xE8, - WBCIR_BANK_5 = 0xEC, - WBCIR_BANK_6 = 0xF0, - WBCIR_BANK_7 = 0xF4, -}; - -/* Supported IR Protocols */ -enum wbcir_protocol { - IR_PROTOCOL_RC5 = 0x0, - IR_PROTOCOL_NEC = 0x1, - IR_PROTOCOL_RC6 = 0x2, -}; - -/* Misc */ -#define WBCIR_NAME "Winbond CIR" -#define WBCIR_ID_FAMILY 0xF1 /* Family ID for the WPCD376I */ -#define WBCIR_ID_CHIP 0x04 /* Chip ID for the WPCD376I */ -#define IR_KEYPRESS_TIMEOUT 250 /* FIXME: should be per-protocol? */ -#define INVALID_SCANCODE 0x7FFFFFFF /* Invalid with all protos */ -#define WAKEUP_IOMEM_LEN 0x10 /* Wake-Up I/O Reg Len */ -#define EHFUNC_IOMEM_LEN 0x10 /* Enhanced Func I/O Reg Len */ -#define SP_IOMEM_LEN 0x08 /* Serial Port 3 (IR) Reg Len */ -#define WBCIR_MAX_IDLE_BYTES 10 - -static DEFINE_SPINLOCK(wbcir_lock); -static DEFINE_RWLOCK(keytable_lock); - -struct wbcir_key { - u32 scancode; - unsigned int keycode; -}; - -struct wbcir_keyentry { - struct wbcir_key key; - struct list_head list; -}; - -static struct wbcir_key rc6_def_keymap[] = { - { 0x800F0400, KEY_NUMERIC_0 }, - { 0x800F0401, KEY_NUMERIC_1 }, - { 0x800F0402, KEY_NUMERIC_2 }, - { 0x800F0403, KEY_NUMERIC_3 }, - { 0x800F0404, KEY_NUMERIC_4 }, - { 0x800F0405, KEY_NUMERIC_5 }, - { 0x800F0406, KEY_NUMERIC_6 }, - { 0x800F0407, KEY_NUMERIC_7 }, - { 0x800F0408, KEY_NUMERIC_8 }, - { 0x800F0409, KEY_NUMERIC_9 }, - { 0x800F041D, KEY_NUMERIC_STAR }, - { 0x800F041C, KEY_NUMERIC_POUND }, - { 0x800F0410, KEY_VOLUMEUP }, - { 0x800F0411, KEY_VOLUMEDOWN }, - { 0x800F0412, KEY_CHANNELUP }, - { 0x800F0413, KEY_CHANNELDOWN }, - { 0x800F040E, KEY_MUTE }, - { 0x800F040D, KEY_VENDOR }, /* Vista Logo Key */ - { 0x800F041E, KEY_UP }, - { 0x800F041F, KEY_DOWN }, - { 0x800F0420, KEY_LEFT }, - { 0x800F0421, KEY_RIGHT }, - { 0x800F0422, KEY_OK }, - { 0x800F0423, KEY_ESC }, - { 0x800F040F, KEY_INFO }, - { 0x800F040A, KEY_CLEAR }, - { 0x800F040B, KEY_ENTER }, - { 0x800F045B, KEY_RED }, - { 0x800F045C, KEY_GREEN }, - { 0x800F045D, KEY_YELLOW }, - { 0x800F045E, KEY_BLUE }, - { 0x800F045A, KEY_TEXT }, - { 0x800F0427, KEY_SWITCHVIDEOMODE }, - { 0x800F040C, KEY_POWER }, - { 0x800F0450, KEY_RADIO }, - { 0x800F0448, KEY_PVR }, - { 0x800F0447, KEY_AUDIO }, - { 0x800F0426, KEY_EPG }, - { 0x800F0449, KEY_CAMERA }, - { 0x800F0425, KEY_TV }, - { 0x800F044A, KEY_VIDEO }, - { 0x800F0424, KEY_DVD }, - { 0x800F0416, KEY_PLAY }, - { 0x800F0418, KEY_PAUSE }, - { 0x800F0419, KEY_STOP }, - { 0x800F0414, KEY_FASTFORWARD }, - { 0x800F041A, KEY_NEXT }, - { 0x800F041B, KEY_PREVIOUS }, - { 0x800F0415, KEY_REWIND }, - { 0x800F0417, KEY_RECORD }, -}; - -/* Registers and other state is protected by wbcir_lock */ -struct wbcir_data { - unsigned long wbase; /* Wake-Up Baseaddr */ - unsigned long ebase; /* Enhanced Func. Baseaddr */ - unsigned long sbase; /* Serial Port Baseaddr */ - unsigned int irq; /* Serial Port IRQ */ - - struct input_dev *input_dev; - struct timer_list timer_keyup; - struct led_trigger *rxtrigger; - struct led_trigger *txtrigger; - struct led_classdev led; - - u32 last_scancode; - unsigned int last_keycode; - u8 last_toggle; - u8 keypressed; - unsigned long keyup_jiffies; - unsigned int idle_count; - - /* RX irdata and parsing state */ - unsigned long irdata[30]; - unsigned int irdata_count; - unsigned int irdata_idle; - unsigned int irdata_off; - unsigned int irdata_error; - - /* Protected by keytable_lock */ - struct list_head keytable; -}; - -static enum wbcir_protocol protocol = IR_PROTOCOL_RC6; -module_param(protocol, uint, 0444); -MODULE_PARM_DESC(protocol, "IR protocol to use " - "(0 = RC5, 1 = NEC, 2 = RC6A, default)"); - -static int invert; /* default = 0 */ -module_param(invert, bool, 0444); -MODULE_PARM_DESC(invert, "Invert the signal from the IR receiver"); - -static unsigned int wake_sc = 0x800F040C; -module_param(wake_sc, uint, 0644); -MODULE_PARM_DESC(wake_sc, "Scancode of the power-on IR command"); - -static unsigned int wake_rc6mode = 6; -module_param(wake_rc6mode, uint, 0644); -MODULE_PARM_DESC(wake_rc6mode, "RC6 mode for the power-on command " - "(0 = 0, 6 = 6A, default)"); - - - -/***************************************************************************** - * - * UTILITY FUNCTIONS - * - *****************************************************************************/ - -/* Caller needs to hold wbcir_lock */ -static void -wbcir_set_bits(unsigned long addr, u8 bits, u8 mask) -{ - u8 val; - - val = inb(addr); - val = ((val & ~mask) | (bits & mask)); - outb(val, addr); -} - -/* Selects the register bank for the serial port */ -static inline void -wbcir_select_bank(struct wbcir_data *data, enum wbcir_bank bank) -{ - outb(bank, data->sbase + WBCIR_REG_SP3_BSR); -} - -static enum led_brightness -wbcir_led_brightness_get(struct led_classdev *led_cdev) -{ - struct wbcir_data *data = container_of(led_cdev, - struct wbcir_data, - led); - - if (inb(data->ebase + WBCIR_REG_ECEIR_CTS) & WBCIR_LED_ENABLE) - return LED_FULL; - else - return LED_OFF; -} - -static void -wbcir_led_brightness_set(struct led_classdev *led_cdev, - enum led_brightness brightness) -{ - struct wbcir_data *data = container_of(led_cdev, - struct wbcir_data, - led); - - wbcir_set_bits(data->ebase + WBCIR_REG_ECEIR_CTS, - brightness == LED_OFF ? 0x00 : WBCIR_LED_ENABLE, - WBCIR_LED_ENABLE); -} - -/* Manchester encodes bits to RC6 message cells (see wbcir_parse_rc6) */ -static u8 -wbcir_to_rc6cells(u8 val) -{ - u8 coded = 0x00; - int i; - - val &= 0x0F; - for (i = 0; i < 4; i++) { - if (val & 0x01) - coded |= 0x02 << (i * 2); - else - coded |= 0x01 << (i * 2); - val >>= 1; - } - - return coded; -} - - - -/***************************************************************************** - * - * INPUT FUNCTIONS - * - *****************************************************************************/ - -static unsigned int -wbcir_do_getkeycode(struct wbcir_data *data, u32 scancode) -{ - struct wbcir_keyentry *keyentry; - unsigned int keycode = KEY_RESERVED; - unsigned long flags; - - read_lock_irqsave(&keytable_lock, flags); - - list_for_each_entry(keyentry, &data->keytable, list) { - if (keyentry->key.scancode == scancode) { - keycode = keyentry->key.keycode; - break; - } - } - - read_unlock_irqrestore(&keytable_lock, flags); - return keycode; -} - -static int -wbcir_getkeycode(struct input_dev *dev, - unsigned int scancode, unsigned int *keycode) -{ - struct wbcir_data *data = input_get_drvdata(dev); - - *keycode = wbcir_do_getkeycode(data, scancode); - return 0; -} - -static int -wbcir_setkeycode(struct input_dev *dev, - unsigned int scancode, unsigned int keycode) -{ - struct wbcir_data *data = input_get_drvdata(dev); - struct wbcir_keyentry *keyentry; - struct wbcir_keyentry *new_keyentry; - unsigned long flags; - unsigned int old_keycode = KEY_RESERVED; - - new_keyentry = kmalloc(sizeof(*new_keyentry), GFP_KERNEL); - if (!new_keyentry) - return -ENOMEM; - - write_lock_irqsave(&keytable_lock, flags); - - list_for_each_entry(keyentry, &data->keytable, list) { - if (keyentry->key.scancode != scancode) - continue; - - old_keycode = keyentry->key.keycode; - keyentry->key.keycode = keycode; - - if (keyentry->key.keycode == KEY_RESERVED) { - list_del(&keyentry->list); - kfree(keyentry); - } - - break; - } - - set_bit(keycode, dev->keybit); - - if (old_keycode == KEY_RESERVED) { - new_keyentry->key.scancode = scancode; - new_keyentry->key.keycode = keycode; - list_add(&new_keyentry->list, &data->keytable); - } else { - kfree(new_keyentry); - clear_bit(old_keycode, dev->keybit); - list_for_each_entry(keyentry, &data->keytable, list) { - if (keyentry->key.keycode == old_keycode) { - set_bit(old_keycode, dev->keybit); - break; - } - } - } - - write_unlock_irqrestore(&keytable_lock, flags); - return 0; -} - -/* - * Timer function to report keyup event some time after keydown is - * reported by the ISR. - */ -static void -wbcir_keyup(unsigned long cookie) -{ - struct wbcir_data *data = (struct wbcir_data *)cookie; - unsigned long flags; - - /* - * data->keyup_jiffies is used to prevent a race condition if a - * hardware interrupt occurs at this point and the keyup timer - * event is moved further into the future as a result. - * - * The timer will then be reactivated and this function called - * again in the future. We need to exit gracefully in that case - * to allow the input subsystem to do its auto-repeat magic or - * a keyup event might follow immediately after the keydown. - */ - - spin_lock_irqsave(&wbcir_lock, flags); - - if (time_is_after_eq_jiffies(data->keyup_jiffies) && data->keypressed) { - data->keypressed = 0; - led_trigger_event(data->rxtrigger, LED_OFF); - input_report_key(data->input_dev, data->last_keycode, 0); - input_sync(data->input_dev); - } - - spin_unlock_irqrestore(&wbcir_lock, flags); -} - -static void -wbcir_keydown(struct wbcir_data *data, u32 scancode, u8 toggle) -{ - unsigned int keycode; - - /* Repeat? */ - if (data->last_scancode == scancode && - data->last_toggle == toggle && - data->keypressed) - goto set_timer; - data->last_scancode = scancode; - - /* Do we need to release an old keypress? */ - if (data->keypressed) { - input_report_key(data->input_dev, data->last_keycode, 0); - input_sync(data->input_dev); - data->keypressed = 0; - } - - /* Report scancode */ - input_event(data->input_dev, EV_MSC, MSC_SCAN, (int)scancode); - - /* Do we know this scancode? */ - keycode = wbcir_do_getkeycode(data, scancode); - if (keycode == KEY_RESERVED) - goto set_timer; - - /* Register a keypress */ - input_report_key(data->input_dev, keycode, 1); - data->keypressed = 1; - data->last_keycode = keycode; - data->last_toggle = toggle; - -set_timer: - input_sync(data->input_dev); - led_trigger_event(data->rxtrigger, - data->keypressed ? LED_FULL : LED_OFF); - data->keyup_jiffies = jiffies + msecs_to_jiffies(IR_KEYPRESS_TIMEOUT); - mod_timer(&data->timer_keyup, data->keyup_jiffies); -} - - - -/***************************************************************************** - * - * IR PARSING FUNCTIONS - * - *****************************************************************************/ - -/* Resets all irdata */ -static void -wbcir_reset_irdata(struct wbcir_data *data) -{ - memset(data->irdata, 0, sizeof(data->irdata)); - data->irdata_count = 0; - data->irdata_off = 0; - data->irdata_error = 0; - data->idle_count = 0; -} - -/* Adds one bit of irdata */ -static void -add_irdata_bit(struct wbcir_data *data, int set) -{ - if (data->irdata_count >= sizeof(data->irdata) * 8) { - data->irdata_error = 1; - return; - } - - if (set) - __set_bit(data->irdata_count, data->irdata); - data->irdata_count++; -} - -/* Gets count bits of irdata */ -static u16 -get_bits(struct wbcir_data *data, int count) -{ - u16 val = 0x0; - - if (data->irdata_count - data->irdata_off < count) { - data->irdata_error = 1; - return 0x0; - } - - while (count > 0) { - val <<= 1; - if (test_bit(data->irdata_off, data->irdata)) - val |= 0x1; - count--; - data->irdata_off++; - } - - return val; -} - -/* Reads 16 cells and converts them to a byte */ -static u8 -wbcir_rc6cells_to_byte(struct wbcir_data *data) -{ - u16 raw = get_bits(data, 16); - u8 val = 0x00; - int bit; - - for (bit = 0; bit < 8; bit++) { - switch (raw & 0x03) { - case 0x01: - break; - case 0x02: - val |= (0x01 << bit); - break; - default: - data->irdata_error = 1; - break; - } - raw >>= 2; - } - - return val; -} - -/* Decodes a number of bits from raw RC5 data */ -static u8 -wbcir_get_rc5bits(struct wbcir_data *data, unsigned int count) -{ - u16 raw = get_bits(data, count * 2); - u8 val = 0x00; - int bit; - - for (bit = 0; bit < count; bit++) { - switch (raw & 0x03) { - case 0x01: - val |= (0x01 << bit); - break; - case 0x02: - break; - default: - data->irdata_error = 1; - break; - } - raw >>= 2; - } - - return val; -} - -static void -wbcir_parse_rc6(struct device *dev, struct wbcir_data *data) -{ - /* - * Normal bits are manchester coded as follows: - * cell0 + cell1 = logic "0" - * cell1 + cell0 = logic "1" - * - * The IR pulse has the following components: - * - * Leader - 6 * cell1 - discarded - * Gap - 2 * cell0 - discarded - * Start bit - Normal Coding - always "1" - * Mode Bit 2 - 0 - Normal Coding - * Toggle bit - Normal Coding with double bit time, - * e.g. cell0 + cell0 + cell1 + cell1 - * means logic "0". - * - * The rest depends on the mode, the following modes are known: - * - * MODE 0: - * Address Bit 7 - 0 - Normal Coding - * Command Bit 7 - 0 - Normal Coding - * - * MODE 6: - * The above Toggle Bit is used as a submode bit, 0 = A, 1 = B. - * Submode B is for pointing devices, only remotes using submode A - * are supported. - * - * Customer range bit - 0 => Customer = 7 bits, 0...127 - * 1 => Customer = 15 bits, 32768...65535 - * Customer Bits - Normal Coding - * - * Customer codes are allocated by Philips. The rest of the bits - * are customer dependent. The following is commonly used (and the - * only supported config): - * - * Toggle Bit - Normal Coding - * Address Bit 6 - 0 - Normal Coding - * Command Bit 7 - 0 - Normal Coding - * - * All modes are followed by at least 6 * cell0. - * - * MODE 0 msglen: - * 1 * 2 (start bit) + 3 * 2 (mode) + 2 * 2 (toggle) + - * 8 * 2 (address) + 8 * 2 (command) = - * 44 cells - * - * MODE 6A msglen: - * 1 * 2 (start bit) + 3 * 2 (mode) + 2 * 2 (submode) + - * 1 * 2 (customer range bit) + 7/15 * 2 (customer bits) + - * 1 * 2 (toggle bit) + 7 * 2 (address) + 8 * 2 (command) = - * 60 - 76 cells - */ - u8 mode; - u8 toggle; - u16 customer = 0x0; - u8 address; - u8 command; - u32 scancode; - - /* Leader mark */ - while (get_bits(data, 1) && !data->irdata_error) - /* Do nothing */; - - /* Leader space */ - if (get_bits(data, 1)) { - dev_dbg(dev, "RC6 - Invalid leader space\n"); - return; - } - - /* Start bit */ - if (get_bits(data, 2) != 0x02) { - dev_dbg(dev, "RC6 - Invalid start bit\n"); - return; - } - - /* Mode */ - mode = get_bits(data, 6); - switch (mode) { - case 0x15: /* 010101 = b000 */ - mode = 0; - break; - case 0x29: /* 101001 = b110 */ - mode = 6; - break; - default: - dev_dbg(dev, "RC6 - Invalid mode\n"); - return; - } - - /* Toggle bit / Submode bit */ - toggle = get_bits(data, 4); - switch (toggle) { - case 0x03: - toggle = 0; - break; - case 0x0C: - toggle = 1; - break; - default: - dev_dbg(dev, "RC6 - Toggle bit error\n"); - break; - } - - /* Customer */ - if (mode == 6) { - if (toggle != 0) { - dev_dbg(dev, "RC6B - Not Supported\n"); - return; - } - - customer = wbcir_rc6cells_to_byte(data); - - if (customer & 0x80) { - /* 15 bit customer value */ - customer <<= 8; - customer |= wbcir_rc6cells_to_byte(data); - } - } - - /* Address */ - address = wbcir_rc6cells_to_byte(data); - if (mode == 6) { - toggle = address >> 7; - address &= 0x7F; - } - - /* Command */ - command = wbcir_rc6cells_to_byte(data); - - /* Create scancode */ - scancode = command; - scancode |= address << 8; - scancode |= customer << 16; - - /* Last sanity check */ - if (data->irdata_error) { - dev_dbg(dev, "RC6 - Cell error(s)\n"); - return; - } - - dev_dbg(dev, "IR-RC6 ad 0x%02X cm 0x%02X cu 0x%04X " - "toggle %u mode %u scan 0x%08X\n", - address, - command, - customer, - (unsigned int)toggle, - (unsigned int)mode, - scancode); - - wbcir_keydown(data, scancode, toggle); -} - -static void -wbcir_parse_rc5(struct device *dev, struct wbcir_data *data) -{ - /* - * Bits are manchester coded as follows: - * cell1 + cell0 = logic "0" - * cell0 + cell1 = logic "1" - * (i.e. the reverse of RC6) - * - * Start bit 1 - "1" - discarded - * Start bit 2 - Must be inverted to get command bit 6 - * Toggle bit - * Address Bit 4 - 0 - * Command Bit 5 - 0 - */ - u8 toggle; - u8 address; - u8 command; - u32 scancode; - - /* Start bit 1 */ - if (!get_bits(data, 1)) { - dev_dbg(dev, "RC5 - Invalid start bit\n"); - return; - } - - /* Start bit 2 */ - if (!wbcir_get_rc5bits(data, 1)) - command = 0x40; - else - command = 0x00; - - toggle = wbcir_get_rc5bits(data, 1); - address = wbcir_get_rc5bits(data, 5); - command |= wbcir_get_rc5bits(data, 6); - scancode = address << 7 | command; - - /* Last sanity check */ - if (data->irdata_error) { - dev_dbg(dev, "RC5 - Invalid message\n"); - return; - } - - dev_dbg(dev, "IR-RC5 ad %u cm %u t %u s %u\n", - (unsigned int)address, - (unsigned int)command, - (unsigned int)toggle, - (unsigned int)scancode); - - wbcir_keydown(data, scancode, toggle); -} - -static void -wbcir_parse_nec(struct device *dev, struct wbcir_data *data) -{ - /* - * Each bit represents 560 us. - * - * Leader - 9 ms burst - * Gap - 4.5 ms silence - * Address1 bit 0 - 7 - Address 1 - * Address2 bit 0 - 7 - Address 2 - * Command1 bit 0 - 7 - Command 1 - * Command2 bit 0 - 7 - Command 2 - * - * Note the bit order! - * - * With the old NEC protocol, Address2 was the inverse of Address1 - * and Command2 was the inverse of Command1 and were used as - * an error check. - * - * With NEC extended, Address1 is the LSB of the Address and - * Address2 is the MSB, Command parsing remains unchanged. - * - * A repeat message is coded as: - * Leader - 9 ms burst - * Gap - 2.25 ms silence - * Repeat - 560 us active - */ - u8 address1; - u8 address2; - u8 command1; - u8 command2; - u16 address; - u32 scancode; - - /* Leader mark */ - while (get_bits(data, 1) && !data->irdata_error) - /* Do nothing */; - - /* Leader space */ - if (get_bits(data, 4)) { - dev_dbg(dev, "NEC - Invalid leader space\n"); - return; - } - - /* Repeat? */ - if (get_bits(data, 1)) { - if (!data->keypressed) { - dev_dbg(dev, "NEC - Stray repeat message\n"); - return; - } - - dev_dbg(dev, "IR-NEC repeat s %u\n", - (unsigned int)data->last_scancode); - - wbcir_keydown(data, data->last_scancode, data->last_toggle); - return; - } - - /* Remaining leader space */ - if (get_bits(data, 3)) { - dev_dbg(dev, "NEC - Invalid leader space\n"); - return; - } - - address1 = bitrev8(get_bits(data, 8)); - address2 = bitrev8(get_bits(data, 8)); - command1 = bitrev8(get_bits(data, 8)); - command2 = bitrev8(get_bits(data, 8)); - - /* Sanity check */ - if (data->irdata_error) { - dev_dbg(dev, "NEC - Invalid message\n"); - return; - } - - /* Check command validity */ - if (command1 != ~command2) { - dev_dbg(dev, "NEC - Command bytes mismatch\n"); - return; - } - - /* Check for extended NEC protocol */ - address = address1; - if (address1 != ~address2) - address |= address2 << 8; - - scancode = address << 8 | command1; - - dev_dbg(dev, "IR-NEC ad %u cm %u s %u\n", - (unsigned int)address, - (unsigned int)command1, - (unsigned int)scancode); - - wbcir_keydown(data, scancode, !data->last_toggle); -} - - - -/***************************************************************************** - * - * INTERRUPT FUNCTIONS - * - *****************************************************************************/ - -static irqreturn_t -wbcir_irq_handler(int irqno, void *cookie) -{ - struct pnp_dev *device = cookie; - struct wbcir_data *data = pnp_get_drvdata(device); - struct device *dev = &device->dev; - u8 status; - unsigned long flags; - u8 irdata[8]; - int i; - unsigned int hw; - - spin_lock_irqsave(&wbcir_lock, flags); - - wbcir_select_bank(data, WBCIR_BANK_0); - - status = inb(data->sbase + WBCIR_REG_SP3_EIR); - - if (!(status & (WBCIR_IRQ_RX | WBCIR_IRQ_ERR))) { - spin_unlock_irqrestore(&wbcir_lock, flags); - return IRQ_NONE; - } - - if (status & WBCIR_IRQ_ERR) - data->irdata_error = 1; - - if (!(status & WBCIR_IRQ_RX)) - goto out; - - /* Since RXHDLEV is set, at least 8 bytes are in the FIFO */ - insb(data->sbase + WBCIR_REG_SP3_RXDATA, &irdata[0], 8); - - for (i = 0; i < sizeof(irdata); i++) { - hw = hweight8(irdata[i]); - if (hw > 4) - add_irdata_bit(data, 0); - else - add_irdata_bit(data, 1); - - if (hw == 8) - data->idle_count++; - else - data->idle_count = 0; - } - - if (data->idle_count > WBCIR_MAX_IDLE_BYTES) { - /* Set RXINACTIVE... */ - outb(WBCIR_RX_DISABLE, data->sbase + WBCIR_REG_SP3_ASCR); - - /* ...and drain the FIFO */ - while (inb(data->sbase + WBCIR_REG_SP3_LSR) & WBCIR_RX_AVAIL) - inb(data->sbase + WBCIR_REG_SP3_RXDATA); - - dev_dbg(dev, "IRDATA:\n"); - for (i = 0; i < data->irdata_count; i += BITS_PER_LONG) - dev_dbg(dev, "0x%08lX\n", data->irdata[i/BITS_PER_LONG]); - - switch (protocol) { - case IR_PROTOCOL_RC5: - wbcir_parse_rc5(dev, data); - break; - case IR_PROTOCOL_RC6: - wbcir_parse_rc6(dev, data); - break; - case IR_PROTOCOL_NEC: - wbcir_parse_nec(dev, data); - break; - } - - wbcir_reset_irdata(data); - } - -out: - spin_unlock_irqrestore(&wbcir_lock, flags); - return IRQ_HANDLED; -} - - - -/***************************************************************************** - * - * SETUP/INIT/SUSPEND/RESUME FUNCTIONS - * - *****************************************************************************/ - -static void -wbcir_shutdown(struct pnp_dev *device) -{ - struct device *dev = &device->dev; - struct wbcir_data *data = pnp_get_drvdata(device); - int do_wake = 1; - u8 match[11]; - u8 mask[11]; - u8 rc6_csl = 0; - int i; - - memset(match, 0, sizeof(match)); - memset(mask, 0, sizeof(mask)); - - if (wake_sc == INVALID_SCANCODE || !device_may_wakeup(dev)) { - do_wake = 0; - goto finish; - } - - switch (protocol) { - case IR_PROTOCOL_RC5: - if (wake_sc > 0xFFF) { - do_wake = 0; - dev_err(dev, "RC5 - Invalid wake scancode\n"); - break; - } - - /* Mask = 13 bits, ex toggle */ - mask[0] = 0xFF; - mask[1] = 0x17; - - match[0] = (wake_sc & 0x003F); /* 6 command bits */ - match[0] |= (wake_sc & 0x0180) >> 1; /* 2 address bits */ - match[1] = (wake_sc & 0x0E00) >> 9; /* 3 address bits */ - if (!(wake_sc & 0x0040)) /* 2nd start bit */ - match[1] |= 0x10; - - break; - - case IR_PROTOCOL_NEC: - if (wake_sc > 0xFFFFFF) { - do_wake = 0; - dev_err(dev, "NEC - Invalid wake scancode\n"); - break; - } - - mask[0] = mask[1] = mask[2] = mask[3] = 0xFF; - - match[1] = bitrev8((wake_sc & 0xFF)); - match[0] = ~match[1]; - - match[3] = bitrev8((wake_sc & 0xFF00) >> 8); - if (wake_sc > 0xFFFF) - match[2] = bitrev8((wake_sc & 0xFF0000) >> 16); - else - match[2] = ~match[3]; - - break; - - case IR_PROTOCOL_RC6: - - if (wake_rc6mode == 0) { - if (wake_sc > 0xFFFF) { - do_wake = 0; - dev_err(dev, "RC6 - Invalid wake scancode\n"); - break; - } - - /* Command */ - match[0] = wbcir_to_rc6cells(wake_sc >> 0); - mask[0] = 0xFF; - match[1] = wbcir_to_rc6cells(wake_sc >> 4); - mask[1] = 0xFF; - - /* Address */ - match[2] = wbcir_to_rc6cells(wake_sc >> 8); - mask[2] = 0xFF; - match[3] = wbcir_to_rc6cells(wake_sc >> 12); - mask[3] = 0xFF; - - /* Header */ - match[4] = 0x50; /* mode1 = mode0 = 0, ignore toggle */ - mask[4] = 0xF0; - match[5] = 0x09; /* start bit = 1, mode2 = 0 */ - mask[5] = 0x0F; - - rc6_csl = 44; - - } else if (wake_rc6mode == 6) { - i = 0; - - /* Command */ - match[i] = wbcir_to_rc6cells(wake_sc >> 0); - mask[i++] = 0xFF; - match[i] = wbcir_to_rc6cells(wake_sc >> 4); - mask[i++] = 0xFF; - - /* Address + Toggle */ - match[i] = wbcir_to_rc6cells(wake_sc >> 8); - mask[i++] = 0xFF; - match[i] = wbcir_to_rc6cells(wake_sc >> 12); - mask[i++] = 0x3F; - - /* Customer bits 7 - 0 */ - match[i] = wbcir_to_rc6cells(wake_sc >> 16); - mask[i++] = 0xFF; - match[i] = wbcir_to_rc6cells(wake_sc >> 20); - mask[i++] = 0xFF; - - if (wake_sc & 0x80000000) { - /* Customer range bit and bits 15 - 8 */ - match[i] = wbcir_to_rc6cells(wake_sc >> 24); - mask[i++] = 0xFF; - match[i] = wbcir_to_rc6cells(wake_sc >> 28); - mask[i++] = 0xFF; - rc6_csl = 76; - } else if (wake_sc <= 0x007FFFFF) { - rc6_csl = 60; - } else { - do_wake = 0; - dev_err(dev, "RC6 - Invalid wake scancode\n"); - break; - } - - /* Header */ - match[i] = 0x93; /* mode1 = mode0 = 1, submode = 0 */ - mask[i++] = 0xFF; - match[i] = 0x0A; /* start bit = 1, mode2 = 1 */ - mask[i++] = 0x0F; - - } else { - do_wake = 0; - dev_err(dev, "RC6 - Invalid wake mode\n"); - } - - break; - - default: - do_wake = 0; - break; - } - -finish: - if (do_wake) { - /* Set compare and compare mask */ - wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_INDEX, - WBCIR_REGSEL_COMPARE | WBCIR_REG_ADDR0, - 0x3F); - outsb(data->wbase + WBCIR_REG_WCEIR_DATA, match, 11); - wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_INDEX, - WBCIR_REGSEL_MASK | WBCIR_REG_ADDR0, - 0x3F); - outsb(data->wbase + WBCIR_REG_WCEIR_DATA, mask, 11); - - /* RC6 Compare String Len */ - outb(rc6_csl, data->wbase + WBCIR_REG_WCEIR_CSL); - - /* Clear status bits NEC_REP, BUFF, MSG_END, MATCH */ - wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_STS, 0x17, 0x17); - - /* Clear BUFF_EN, Clear END_EN, Set MATCH_EN */ - wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_EV_EN, 0x01, 0x07); - - /* Set CEIR_EN */ - wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CTL, 0x01, 0x01); - - } else { - /* Clear BUFF_EN, Clear END_EN, Clear MATCH_EN */ - wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_EV_EN, 0x00, 0x07); - - /* Clear CEIR_EN */ - wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CTL, 0x00, 0x01); - } - - /* Disable interrupts */ - wbcir_select_bank(data, WBCIR_BANK_0); - outb(WBCIR_IRQ_NONE, data->sbase + WBCIR_REG_SP3_IER); - - /* - * ACPI will set the HW disable bit for SP3 which means that the - * output signals are left in an undefined state which may cause - * spurious interrupts which we need to ignore until the hardware - * is reinitialized. - */ - disable_irq(data->irq); -} - -static int -wbcir_suspend(struct pnp_dev *device, pm_message_t state) -{ - wbcir_shutdown(device); - return 0; -} - -static void -wbcir_init_hw(struct wbcir_data *data) -{ - u8 tmp; - - /* Disable interrupts */ - wbcir_select_bank(data, WBCIR_BANK_0); - outb(WBCIR_IRQ_NONE, data->sbase + WBCIR_REG_SP3_IER); - - /* Set PROT_SEL, RX_INV, Clear CEIR_EN (needed for the led) */ - tmp = protocol << 4; - if (invert) - tmp |= 0x08; - outb(tmp, data->wbase + WBCIR_REG_WCEIR_CTL); - - /* Clear status bits NEC_REP, BUFF, MSG_END, MATCH */ - wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_STS, 0x17, 0x17); - - /* Clear BUFF_EN, Clear END_EN, Clear MATCH_EN */ - wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_EV_EN, 0x00, 0x07); - - /* Set RC5 cell time to correspond to 36 kHz */ - wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CFG1, 0x4A, 0x7F); - - /* Set IRTX_INV */ - if (invert) - outb(0x04, data->ebase + WBCIR_REG_ECEIR_CCTL); - else - outb(0x00, data->ebase + WBCIR_REG_ECEIR_CCTL); - - /* - * Clear IR LED, set SP3 clock to 24Mhz - * set SP3_IRRX_SW to binary 01, helpfully not documented - */ - outb(0x10, data->ebase + WBCIR_REG_ECEIR_CTS); - - /* Enable extended mode */ - wbcir_select_bank(data, WBCIR_BANK_2); - outb(WBCIR_EXT_ENABLE, data->sbase + WBCIR_REG_SP3_EXCR1); - - /* - * Configure baud generator, IR data will be sampled at - * a bitrate of: (24Mhz * prescaler) / (divisor * 16). - * - * The ECIR registers include a flag to change the - * 24Mhz clock freq to 48Mhz. - * - * It's not documented in the specs, but fifo levels - * other than 16 seems to be unsupported. - */ - - /* prescaler 1.0, tx/rx fifo lvl 16 */ - outb(0x30, data->sbase + WBCIR_REG_SP3_EXCR2); - - /* Set baud divisor to generate one byte per bit/cell */ - switch (protocol) { - case IR_PROTOCOL_RC5: - outb(0xA7, data->sbase + WBCIR_REG_SP3_BGDL); - break; - case IR_PROTOCOL_RC6: - outb(0x53, data->sbase + WBCIR_REG_SP3_BGDL); - break; - case IR_PROTOCOL_NEC: - outb(0x69, data->sbase + WBCIR_REG_SP3_BGDL); - break; - } - outb(0x00, data->sbase + WBCIR_REG_SP3_BGDH); - - /* Set CEIR mode */ - wbcir_select_bank(data, WBCIR_BANK_0); - outb(0xC0, data->sbase + WBCIR_REG_SP3_MCR); - inb(data->sbase + WBCIR_REG_SP3_LSR); /* Clear LSR */ - inb(data->sbase + WBCIR_REG_SP3_MSR); /* Clear MSR */ - - /* Disable RX demod, run-length encoding/decoding, set freq span */ - wbcir_select_bank(data, WBCIR_BANK_7); - outb(0x10, data->sbase + WBCIR_REG_SP3_RCCFG); - - /* Disable timer */ - wbcir_select_bank(data, WBCIR_BANK_4); - outb(0x00, data->sbase + WBCIR_REG_SP3_IRCR1); - - /* Enable MSR interrupt, Clear AUX_IRX */ - wbcir_select_bank(data, WBCIR_BANK_5); - outb(0x00, data->sbase + WBCIR_REG_SP3_IRCR2); - - /* Disable CRC */ - wbcir_select_bank(data, WBCIR_BANK_6); - outb(0x20, data->sbase + WBCIR_REG_SP3_IRCR3); - - /* Set RX/TX (de)modulation freq, not really used */ - wbcir_select_bank(data, WBCIR_BANK_7); - outb(0xF2, data->sbase + WBCIR_REG_SP3_IRRXDC); - outb(0x69, data->sbase + WBCIR_REG_SP3_IRTXMC); - - /* Set invert and pin direction */ - if (invert) - outb(0x10, data->sbase + WBCIR_REG_SP3_IRCFG4); - else - outb(0x00, data->sbase + WBCIR_REG_SP3_IRCFG4); - - /* Set FIFO thresholds (RX = 8, TX = 3), reset RX/TX */ - wbcir_select_bank(data, WBCIR_BANK_0); - outb(0x97, data->sbase + WBCIR_REG_SP3_FCR); - - /* Clear AUX status bits */ - outb(0xE0, data->sbase + WBCIR_REG_SP3_ASCR); - - /* Enable interrupts */ - wbcir_reset_irdata(data); - outb(WBCIR_IRQ_RX | WBCIR_IRQ_ERR, data->sbase + WBCIR_REG_SP3_IER); -} - -static int -wbcir_resume(struct pnp_dev *device) -{ - struct wbcir_data *data = pnp_get_drvdata(device); - - wbcir_init_hw(data); - enable_irq(data->irq); - - return 0; -} - -static int __devinit -wbcir_probe(struct pnp_dev *device, const struct pnp_device_id *dev_id) -{ - struct device *dev = &device->dev; - struct wbcir_data *data; - int err; - - if (!(pnp_port_len(device, 0) == EHFUNC_IOMEM_LEN && - pnp_port_len(device, 1) == WAKEUP_IOMEM_LEN && - pnp_port_len(device, 2) == SP_IOMEM_LEN)) { - dev_err(dev, "Invalid resources\n"); - return -ENODEV; - } - - data = kzalloc(sizeof(*data), GFP_KERNEL); - if (!data) { - err = -ENOMEM; - goto exit; - } - - pnp_set_drvdata(device, data); - - data->ebase = pnp_port_start(device, 0); - data->wbase = pnp_port_start(device, 1); - data->sbase = pnp_port_start(device, 2); - data->irq = pnp_irq(device, 0); - - if (data->wbase == 0 || data->ebase == 0 || - data->sbase == 0 || data->irq == 0) { - err = -ENODEV; - dev_err(dev, "Invalid resources\n"); - goto exit_free_data; - } - - dev_dbg(&device->dev, "Found device " - "(w: 0x%lX, e: 0x%lX, s: 0x%lX, i: %u)\n", - data->wbase, data->ebase, data->sbase, data->irq); - - if (!request_region(data->wbase, WAKEUP_IOMEM_LEN, DRVNAME)) { - dev_err(dev, "Region 0x%lx-0x%lx already in use!\n", - data->wbase, data->wbase + WAKEUP_IOMEM_LEN - 1); - err = -EBUSY; - goto exit_free_data; - } - - if (!request_region(data->ebase, EHFUNC_IOMEM_LEN, DRVNAME)) { - dev_err(dev, "Region 0x%lx-0x%lx already in use!\n", - data->ebase, data->ebase + EHFUNC_IOMEM_LEN - 1); - err = -EBUSY; - goto exit_release_wbase; - } - - if (!request_region(data->sbase, SP_IOMEM_LEN, DRVNAME)) { - dev_err(dev, "Region 0x%lx-0x%lx already in use!\n", - data->sbase, data->sbase + SP_IOMEM_LEN - 1); - err = -EBUSY; - goto exit_release_ebase; - } - - err = request_irq(data->irq, wbcir_irq_handler, - IRQF_DISABLED, DRVNAME, device); - if (err) { - dev_err(dev, "Failed to claim IRQ %u\n", data->irq); - err = -EBUSY; - goto exit_release_sbase; - } - - led_trigger_register_simple("cir-tx", &data->txtrigger); - if (!data->txtrigger) { - err = -ENOMEM; - goto exit_free_irq; - } - - led_trigger_register_simple("cir-rx", &data->rxtrigger); - if (!data->rxtrigger) { - err = -ENOMEM; - goto exit_unregister_txtrigger; - } - - data->led.name = "cir::activity"; - data->led.default_trigger = "cir-rx"; - data->led.brightness_set = wbcir_led_brightness_set; - data->led.brightness_get = wbcir_led_brightness_get; - err = led_classdev_register(&device->dev, &data->led); - if (err) - goto exit_unregister_rxtrigger; - - data->input_dev = input_allocate_device(); - if (!data->input_dev) { - err = -ENOMEM; - goto exit_unregister_led; - } - - data->input_dev->evbit[0] = BIT(EV_KEY); - data->input_dev->name = WBCIR_NAME; - data->input_dev->phys = "wbcir/cir0"; - data->input_dev->id.bustype = BUS_HOST; - data->input_dev->id.vendor = PCI_VENDOR_ID_WINBOND; - data->input_dev->id.product = WBCIR_ID_FAMILY; - data->input_dev->id.version = WBCIR_ID_CHIP; - data->input_dev->getkeycode = wbcir_getkeycode; - data->input_dev->setkeycode = wbcir_setkeycode; - input_set_capability(data->input_dev, EV_MSC, MSC_SCAN); - input_set_drvdata(data->input_dev, data); - - err = input_register_device(data->input_dev); - if (err) - goto exit_free_input; - - data->last_scancode = INVALID_SCANCODE; - INIT_LIST_HEAD(&data->keytable); - setup_timer(&data->timer_keyup, wbcir_keyup, (unsigned long)data); - - /* Load default keymaps */ - if (protocol == IR_PROTOCOL_RC6) { - int i; - for (i = 0; i < ARRAY_SIZE(rc6_def_keymap); i++) { - err = wbcir_setkeycode(data->input_dev, - (int)rc6_def_keymap[i].scancode, - (int)rc6_def_keymap[i].keycode); - if (err) - goto exit_unregister_keys; - } - } - - device_init_wakeup(&device->dev, 1); - - wbcir_init_hw(data); - - return 0; - -exit_unregister_keys: - if (!list_empty(&data->keytable)) { - struct wbcir_keyentry *key; - struct wbcir_keyentry *keytmp; - - list_for_each_entry_safe(key, keytmp, &data->keytable, list) { - list_del(&key->list); - kfree(key); - } - } - input_unregister_device(data->input_dev); - /* Can't call input_free_device on an unregistered device */ - data->input_dev = NULL; -exit_free_input: - input_free_device(data->input_dev); -exit_unregister_led: - led_classdev_unregister(&data->led); -exit_unregister_rxtrigger: - led_trigger_unregister_simple(data->rxtrigger); -exit_unregister_txtrigger: - led_trigger_unregister_simple(data->txtrigger); -exit_free_irq: - free_irq(data->irq, device); -exit_release_sbase: - release_region(data->sbase, SP_IOMEM_LEN); -exit_release_ebase: - release_region(data->ebase, EHFUNC_IOMEM_LEN); -exit_release_wbase: - release_region(data->wbase, WAKEUP_IOMEM_LEN); -exit_free_data: - kfree(data); - pnp_set_drvdata(device, NULL); -exit: - return err; -} - -static void __devexit -wbcir_remove(struct pnp_dev *device) -{ - struct wbcir_data *data = pnp_get_drvdata(device); - struct wbcir_keyentry *key; - struct wbcir_keyentry *keytmp; - - /* Disable interrupts */ - wbcir_select_bank(data, WBCIR_BANK_0); - outb(WBCIR_IRQ_NONE, data->sbase + WBCIR_REG_SP3_IER); - - del_timer_sync(&data->timer_keyup); - - free_irq(data->irq, device); - - /* Clear status bits NEC_REP, BUFF, MSG_END, MATCH */ - wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_STS, 0x17, 0x17); - - /* Clear CEIR_EN */ - wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CTL, 0x00, 0x01); - - /* Clear BUFF_EN, END_EN, MATCH_EN */ - wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_EV_EN, 0x00, 0x07); - - /* This will generate a keyup event if necessary */ - input_unregister_device(data->input_dev); - - led_trigger_unregister_simple(data->rxtrigger); - led_trigger_unregister_simple(data->txtrigger); - led_classdev_unregister(&data->led); - - /* This is ok since &data->led isn't actually used */ - wbcir_led_brightness_set(&data->led, LED_OFF); - - release_region(data->wbase, WAKEUP_IOMEM_LEN); - release_region(data->ebase, EHFUNC_IOMEM_LEN); - release_region(data->sbase, SP_IOMEM_LEN); - - list_for_each_entry_safe(key, keytmp, &data->keytable, list) { - list_del(&key->list); - kfree(key); - } - - kfree(data); - - pnp_set_drvdata(device, NULL); -} - -static const struct pnp_device_id wbcir_ids[] = { - { "WEC1022", 0 }, - { "", 0 } -}; -MODULE_DEVICE_TABLE(pnp, wbcir_ids); - -static struct pnp_driver wbcir_driver = { - .name = WBCIR_NAME, - .id_table = wbcir_ids, - .probe = wbcir_probe, - .remove = __devexit_p(wbcir_remove), - .suspend = wbcir_suspend, - .resume = wbcir_resume, - .shutdown = wbcir_shutdown -}; - -static int __init -wbcir_init(void) -{ - int ret; - - switch (protocol) { - case IR_PROTOCOL_RC5: - case IR_PROTOCOL_NEC: - case IR_PROTOCOL_RC6: - break; - default: - printk(KERN_ERR DRVNAME ": Invalid protocol argument\n"); - return -EINVAL; - } - - ret = pnp_register_driver(&wbcir_driver); - if (ret) - printk(KERN_ERR DRVNAME ": Unable to register driver\n"); - - return ret; -} - -static void __exit -wbcir_exit(void) -{ - pnp_unregister_driver(&wbcir_driver); -} - -MODULE_AUTHOR("David Härdeman <david@hardeman.nu>"); -MODULE_DESCRIPTION("Winbond SuperI/O Consumer IR Driver"); -MODULE_LICENSE("GPL"); - -module_init(wbcir_init); -module_exit(wbcir_exit); - - |