diff options
Diffstat (limited to 'drivers/media/i2c/s5k6aa.c')
| -rw-r--r-- | drivers/media/i2c/s5k6aa.c | 1664 |
1 files changed, 1664 insertions, 0 deletions
diff --git a/drivers/media/i2c/s5k6aa.c b/drivers/media/i2c/s5k6aa.c new file mode 100644 index 00000000000..57cd4fa0193 --- /dev/null +++ b/drivers/media/i2c/s5k6aa.c @@ -0,0 +1,1664 @@ +/* + * Driver for Samsung S5K6AAFX SXGA 1/6" 1.3M CMOS Image Sensor + * with embedded SoC ISP. + * + * Copyright (C) 2011, Samsung Electronics Co., Ltd. + * Sylwester Nawrocki <s.nawrocki@samsung.com> + * + * Based on a driver authored by Dongsoo Nathaniel Kim. + * Copyright (C) 2009, Dongsoo Nathaniel Kim <dongsoo45.kim@samsung.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#include <linux/clk.h> +#include <linux/delay.h> +#include <linux/gpio.h> +#include <linux/i2c.h> +#include <linux/media.h> +#include <linux/module.h> +#include <linux/regulator/consumer.h> +#include <linux/slab.h> + +#include <media/media-entity.h> +#include <media/v4l2-ctrls.h> +#include <media/v4l2-device.h> +#include <media/v4l2-subdev.h> +#include <media/v4l2-mediabus.h> +#include <media/s5k6aa.h> + +static int debug; +module_param(debug, int, 0644); + +#define DRIVER_NAME "S5K6AA" + +/* The token to indicate array termination */ +#define S5K6AA_TERM 0xffff +#define S5K6AA_OUT_WIDTH_DEF 640 +#define S5K6AA_OUT_HEIGHT_DEF 480 +#define S5K6AA_WIN_WIDTH_MAX 1280 +#define S5K6AA_WIN_HEIGHT_MAX 1024 +#define S5K6AA_WIN_WIDTH_MIN 8 +#define S5K6AA_WIN_HEIGHT_MIN 8 + +/* + * H/W register Interface (0xD0000000 - 0xD0000FFF) + */ +#define AHB_MSB_ADDR_PTR 0xfcfc +#define GEN_REG_OFFSH 0xd000 +#define REG_CMDWR_ADDRH 0x0028 +#define REG_CMDWR_ADDRL 0x002a +#define REG_CMDRD_ADDRH 0x002c +#define REG_CMDRD_ADDRL 0x002e +#define REG_CMDBUF0_ADDR 0x0f12 +#define REG_CMDBUF1_ADDR 0x0f10 + +/* + * Host S/W Register interface (0x70000000 - 0x70002000) + * The value of the two most significant address bytes is 0x7000, + * (HOST_SWIF_OFFS_H). The register addresses below specify 2 LSBs. + */ +#define HOST_SWIF_OFFSH 0x7000 + +/* Initialization parameters */ +/* Master clock frequency in KHz */ +#define REG_I_INCLK_FREQ_L 0x01b8 +#define REG_I_INCLK_FREQ_H 0x01ba +#define MIN_MCLK_FREQ_KHZ 6000U +#define MAX_MCLK_FREQ_KHZ 27000U +#define REG_I_USE_NPVI_CLOCKS 0x01c6 +#define REG_I_USE_NMIPI_CLOCKS 0x01c8 + +/* Clock configurations, n = 0..2. REG_I_* frequency unit is 4 kHz. */ +#define REG_I_OPCLK_4KHZ(n) ((n) * 6 + 0x01cc) +#define REG_I_MIN_OUTRATE_4KHZ(n) ((n) * 6 + 0x01ce) +#define REG_I_MAX_OUTRATE_4KHZ(n) ((n) * 6 + 0x01d0) +#define SYS_PLL_OUT_FREQ (48000000 / 4000) +#define PCLK_FREQ_MIN (24000000 / 4000) +#define PCLK_FREQ_MAX (48000000 / 4000) +#define REG_I_INIT_PARAMS_UPDATED 0x01e0 +#define REG_I_ERROR_INFO 0x01e2 + +/* General purpose parameters */ +#define REG_USER_BRIGHTNESS 0x01e4 +#define REG_USER_CONTRAST 0x01e6 +#define REG_USER_SATURATION 0x01e8 +#define REG_USER_SHARPBLUR 0x01ea + +#define REG_G_SPEC_EFFECTS 0x01ee +#define REG_G_ENABLE_PREV 0x01f0 +#define REG_G_ENABLE_PREV_CHG 0x01f2 +#define REG_G_NEW_CFG_SYNC 0x01f8 +#define REG_G_PREVZOOM_IN_WIDTH 0x020a +#define REG_G_PREVZOOM_IN_HEIGHT 0x020c +#define REG_G_PREVZOOM_IN_XOFFS 0x020e +#define REG_G_PREVZOOM_IN_YOFFS 0x0210 +#define REG_G_INPUTS_CHANGE_REQ 0x021a +#define REG_G_ACTIVE_PREV_CFG 0x021c +#define REG_G_PREV_CFG_CHG 0x021e +#define REG_G_PREV_OPEN_AFTER_CH 0x0220 +#define REG_G_PREV_CFG_ERROR 0x0222 + +/* Preview control section. n = 0...4. */ +#define PREG(n, x) ((n) * 0x26 + x) +#define REG_P_OUT_WIDTH(n) PREG(n, 0x0242) +#define REG_P_OUT_HEIGHT(n) PREG(n, 0x0244) +#define REG_P_FMT(n) PREG(n, 0x0246) +#define REG_P_MAX_OUT_RATE(n) PREG(n, 0x0248) +#define REG_P_MIN_OUT_RATE(n) PREG(n, 0x024a) +#define REG_P_PVI_MASK(n) PREG(n, 0x024c) +#define REG_P_CLK_INDEX(n) PREG(n, 0x024e) +#define REG_P_FR_RATE_TYPE(n) PREG(n, 0x0250) +#define FR_RATE_DYNAMIC 0 +#define FR_RATE_FIXED 1 +#define FR_RATE_FIXED_ACCURATE 2 +#define REG_P_FR_RATE_Q_TYPE(n) PREG(n, 0x0252) +#define FR_RATE_Q_BEST_FRRATE 1 /* Binning enabled */ +#define FR_RATE_Q_BEST_QUALITY 2 /* Binning disabled */ +/* Frame period in 0.1 ms units */ +#define REG_P_MAX_FR_TIME(n) PREG(n, 0x0254) +#define REG_P_MIN_FR_TIME(n) PREG(n, 0x0256) +/* Conversion to REG_P_[MAX/MIN]_FR_TIME value; __t: time in us */ +#define US_TO_FR_TIME(__t) ((__t) / 100) +#define S5K6AA_MIN_FR_TIME 33300 /* us */ +#define S5K6AA_MAX_FR_TIME 650000 /* us */ +#define S5K6AA_MAX_HIGHRES_FR_TIME 666 /* x100 us */ +/* The below 5 registers are for "device correction" values */ +#define REG_P_COLORTEMP(n) PREG(n, 0x025e) +#define REG_P_PREV_MIRROR(n) PREG(n, 0x0262) + +/* Extended image property controls */ +/* Exposure time in 10 us units */ +#define REG_SF_USR_EXPOSURE_L 0x03c6 +#define REG_SF_USR_EXPOSURE_H 0x03c8 +#define REG_SF_USR_EXPOSURE_CHG 0x03ca +#define REG_SF_USR_TOT_GAIN 0x03cc +#define REG_SF_USR_TOT_GAIN_CHG 0x03ce +#define REG_SF_RGAIN 0x03d0 +#define REG_SF_RGAIN_CHG 0x03d2 +#define REG_SF_GGAIN 0x03d4 +#define REG_SF_GGAIN_CHG 0x03d6 +#define REG_SF_BGAIN 0x03d8 +#define REG_SF_BGAIN_CHG 0x03da +#define REG_SF_FLICKER_QUANT 0x03dc +#define REG_SF_FLICKER_QUANT_CHG 0x03de + +/* Output interface (parallel/MIPI) setup */ +#define REG_OIF_EN_MIPI_LANES 0x03fa +#define REG_OIF_EN_PACKETS 0x03fc +#define REG_OIF_CFG_CHG 0x03fe + +/* Auto-algorithms enable mask */ +#define REG_DBG_AUTOALG_EN 0x0400 +#define AALG_ALL_EN_MASK (1 << 0) +#define AALG_AE_EN_MASK (1 << 1) +#define AALG_DIVLEI_EN_MASK (1 << 2) +#define AALG_WB_EN_MASK (1 << 3) +#define AALG_FLICKER_EN_MASK (1 << 5) +#define AALG_FIT_EN_MASK (1 << 6) +#define AALG_WRHW_EN_MASK (1 << 7) + +/* Firmware revision information */ +#define REG_FW_APIVER 0x012e +#define S5K6AAFX_FW_APIVER 0x0001 +#define REG_FW_REVISION 0x0130 + +/* For now we use only one user configuration register set */ +#define S5K6AA_MAX_PRESETS 1 + +static const char * const s5k6aa_supply_names[] = { + "vdd_core", /* Digital core supply 1.5V (1.4V to 1.6V) */ + "vdda", /* Analog power supply 2.8V (2.6V to 3.0V) */ + "vdd_reg", /* Regulator input power 1.8V (1.7V to 1.9V) + or 2.8V (2.6V to 3.0) */ + "vddio", /* I/O supply 1.8V (1.65V to 1.95V) + or 2.8V (2.5V to 3.1V) */ +}; +#define S5K6AA_NUM_SUPPLIES ARRAY_SIZE(s5k6aa_supply_names) + +enum s5k6aa_gpio_id { + STBY, + RST, + GPIO_NUM, +}; + +struct s5k6aa_regval { + u16 addr; + u16 val; +}; + +struct s5k6aa_pixfmt { + enum v4l2_mbus_pixelcode code; + u32 colorspace; + /* REG_P_FMT(x) register value */ + u16 reg_p_fmt; +}; + +struct s5k6aa_preset { + /* output pixel format and resolution */ + struct v4l2_mbus_framefmt mbus_fmt; + u8 clk_id; + u8 index; +}; + +struct s5k6aa_ctrls { + struct v4l2_ctrl_handler handler; + /* Auto / manual white balance cluster */ + struct v4l2_ctrl *awb; + struct v4l2_ctrl *gain_red; + struct v4l2_ctrl *gain_blue; + struct v4l2_ctrl *gain_green; + /* Mirror cluster */ + struct v4l2_ctrl *hflip; + struct v4l2_ctrl *vflip; + /* Auto exposure / manual exposure and gain cluster */ + struct v4l2_ctrl *auto_exp; + struct v4l2_ctrl *exposure; + struct v4l2_ctrl *gain; +}; + +struct s5k6aa_interval { + u16 reg_fr_time; + struct v4l2_fract interval; + /* Maximum rectangle for the interval */ + struct v4l2_frmsize_discrete size; +}; + +struct s5k6aa { + struct v4l2_subdev sd; + struct media_pad pad; + + enum v4l2_mbus_type bus_type; + u8 mipi_lanes; + + int (*s_power)(int enable); + struct regulator_bulk_data supplies[S5K6AA_NUM_SUPPLIES]; + struct s5k6aa_gpio gpio[GPIO_NUM]; + + /* external master clock frequency */ + unsigned long mclk_frequency; + /* ISP internal master clock frequency */ + u16 clk_fop; + /* output pixel clock frequency range */ + u16 pclk_fmin; + u16 pclk_fmax; + + unsigned int inv_hflip:1; + unsigned int inv_vflip:1; + + /* protects the struct members below */ + struct mutex lock; + + /* sensor matrix scan window */ + struct v4l2_rect ccd_rect; + + struct s5k6aa_ctrls ctrls; + struct s5k6aa_preset presets[S5K6AA_MAX_PRESETS]; + struct s5k6aa_preset *preset; + const struct s5k6aa_interval *fiv; + + unsigned int streaming:1; + unsigned int apply_cfg:1; + unsigned int apply_crop:1; + unsigned int power; +}; + +static struct s5k6aa_regval s5k6aa_analog_config[] = { + /* Analog settings */ + { 0x112a, 0x0000 }, { 0x1132, 0x0000 }, + { 0x113e, 0x0000 }, { 0x115c, 0x0000 }, + { 0x1164, 0x0000 }, { 0x1174, 0x0000 }, + { 0x1178, 0x0000 }, { 0x077a, 0x0000 }, + { 0x077c, 0x0000 }, { 0x077e, 0x0000 }, + { 0x0780, 0x0000 }, { 0x0782, 0x0000 }, + { 0x0784, 0x0000 }, { 0x0786, 0x0000 }, + { 0x0788, 0x0000 }, { 0x07a2, 0x0000 }, + { 0x07a4, 0x0000 }, { 0x07a6, 0x0000 }, + { 0x07a8, 0x0000 }, { 0x07b6, 0x0000 }, + { 0x07b8, 0x0002 }, { 0x07ba, 0x0004 }, + { 0x07bc, 0x0004 }, { 0x07be, 0x0005 }, + { 0x07c0, 0x0005 }, { S5K6AA_TERM, 0 }, +}; + +/* TODO: Add RGB888 and Bayer format */ +static const struct s5k6aa_pixfmt s5k6aa_formats[] = { + { V4L2_MBUS_FMT_YUYV8_2X8, V4L2_COLORSPACE_JPEG, 5 }, + /* range 16-240 */ + { V4L2_MBUS_FMT_YUYV8_2X8, V4L2_COLORSPACE_REC709, 6 }, + { V4L2_MBUS_FMT_RGB565_2X8_BE, V4L2_COLORSPACE_JPEG, 0 }, +}; + +static const struct s5k6aa_interval s5k6aa_intervals[] = { + { 1000, {10000, 1000000}, {1280, 1024} }, /* 10 fps */ + { 666, {15000, 1000000}, {1280, 1024} }, /* 15 fps */ + { 500, {20000, 1000000}, {1280, 720} }, /* 20 fps */ + { 400, {25000, 1000000}, {640, 480} }, /* 25 fps */ + { 333, {33300, 1000000}, {640, 480} }, /* 30 fps */ +}; + +#define S5K6AA_INTERVAL_DEF_INDEX 1 /* 15 fps */ + +static inline struct v4l2_subdev *ctrl_to_sd(struct v4l2_ctrl *ctrl) +{ + return &container_of(ctrl->handler, struct s5k6aa, ctrls.handler)->sd; +} + +static inline struct s5k6aa *to_s5k6aa(struct v4l2_subdev *sd) +{ + return container_of(sd, struct s5k6aa, sd); +} + +/* Set initial values for all preview presets */ +static void s5k6aa_presets_data_init(struct s5k6aa *s5k6aa) +{ + struct s5k6aa_preset *preset = &s5k6aa->presets[0]; + int i; + + for (i = 0; i < S5K6AA_MAX_PRESETS; i++) { + preset->mbus_fmt.width = S5K6AA_OUT_WIDTH_DEF; + preset->mbus_fmt.height = S5K6AA_OUT_HEIGHT_DEF; + preset->mbus_fmt.code = s5k6aa_formats[0].code; + preset->index = i; + preset->clk_id = 0; + preset++; + } + + s5k6aa->fiv = &s5k6aa_intervals[S5K6AA_INTERVAL_DEF_INDEX]; + s5k6aa->preset = &s5k6aa->presets[0]; +} + +static int s5k6aa_i2c_read(struct i2c_client *client, u16 addr, u16 *val) +{ + u8 wbuf[2] = {addr >> 8, addr & 0xFF}; + struct i2c_msg msg[2]; + u8 rbuf[2]; + int ret; + + msg[0].addr = client->addr; + msg[0].flags = 0; + msg[0].len = 2; + msg[0].buf = wbuf; + + msg[1].addr = client->addr; + msg[1].flags = I2C_M_RD; + msg[1].len = 2; + msg[1].buf = rbuf; + + ret = i2c_transfer(client->adapter, msg, 2); + *val = be16_to_cpu(*((u16 *)rbuf)); + + v4l2_dbg(3, debug, client, "i2c_read: 0x%04X : 0x%04x\n", addr, *val); + + return ret == 2 ? 0 : ret; +} + +static int s5k6aa_i2c_write(struct i2c_client *client, u16 addr, u16 val) +{ + u8 buf[4] = {addr >> 8, addr & 0xFF, val >> 8, val & 0xFF}; + + int ret = i2c_master_send(client, buf, 4); + v4l2_dbg(3, debug, client, "i2c_write: 0x%04X : 0x%04x\n", addr, val); + + return ret == 4 ? 0 : ret; +} + +/* The command register write, assumes Command_Wr_addH = 0x7000. */ +static int s5k6aa_write(struct i2c_client *c, u16 addr, u16 val) +{ + int ret = s5k6aa_i2c_write(c, REG_CMDWR_ADDRL, addr); + if (ret) + return ret; + return s5k6aa_i2c_write(c, REG_CMDBUF0_ADDR, val); +} + +/* The command register read, assumes Command_Rd_addH = 0x7000. */ +static int s5k6aa_read(struct i2c_client *client, u16 addr, u16 *val) +{ + int ret = s5k6aa_i2c_write(client, REG_CMDRD_ADDRL, addr); + if (ret) + return ret; + return s5k6aa_i2c_read(client, REG_CMDBUF0_ADDR, val); +} + +static int s5k6aa_write_array(struct v4l2_subdev *sd, + const struct s5k6aa_regval *msg) +{ + struct i2c_client *client = v4l2_get_subdevdata(sd); + u16 addr_incr = 0; + int ret = 0; + + while (msg->addr != S5K6AA_TERM) { + if (addr_incr != 2) + ret = s5k6aa_i2c_write(client, REG_CMDWR_ADDRL, + msg->addr); + if (ret) + break; + ret = s5k6aa_i2c_write(client, REG_CMDBUF0_ADDR, msg->val); + if (ret) + break; + /* Assume that msg->addr is always less than 0xfffc */ + addr_incr = (msg + 1)->addr - msg->addr; + msg++; + } + + return ret; +} + +/* Configure the AHB high address bytes for GTG registers access */ +static int s5k6aa_set_ahb_address(struct i2c_client *client) +{ + int ret = s5k6aa_i2c_write(client, AHB_MSB_ADDR_PTR, GEN_REG_OFFSH); + if (ret) + return ret; + ret = s5k6aa_i2c_write(client, REG_CMDRD_ADDRH, HOST_SWIF_OFFSH); + if (ret) + return ret; + return s5k6aa_i2c_write(client, REG_CMDWR_ADDRH, HOST_SWIF_OFFSH); +} + +/** + * s5k6aa_configure_pixel_clock - apply ISP main clock/PLL configuration + * + * Configure the internal ISP PLL for the required output frequency. + * Locking: called with s5k6aa.lock mutex held. + */ +static int s5k6aa_configure_pixel_clocks(struct s5k6aa *s5k6aa) +{ + struct i2c_client *c = v4l2_get_subdevdata(&s5k6aa->sd); + unsigned long fmclk = s5k6aa->mclk_frequency / 1000; + u16 status; + int ret; + + if (WARN(fmclk < MIN_MCLK_FREQ_KHZ || fmclk > MAX_MCLK_FREQ_KHZ, + "Invalid clock frequency: %ld\n", fmclk)) + return -EINVAL; + + s5k6aa->pclk_fmin = PCLK_FREQ_MIN; + s5k6aa->pclk_fmax = PCLK_FREQ_MAX; + s5k6aa->clk_fop = SYS_PLL_OUT_FREQ; + + /* External input clock frequency in kHz */ + ret = s5k6aa_write(c, REG_I_INCLK_FREQ_H, fmclk >> 16); + if (!ret) + ret = s5k6aa_write(c, REG_I_INCLK_FREQ_L, fmclk & 0xFFFF); + if (!ret) + ret = s5k6aa_write(c, REG_I_USE_NPVI_CLOCKS, 1); + /* Internal PLL frequency */ + if (!ret) + ret = s5k6aa_write(c, REG_I_OPCLK_4KHZ(0), s5k6aa->clk_fop); + if (!ret) + ret = s5k6aa_write(c, REG_I_MIN_OUTRATE_4KHZ(0), + s5k6aa->pclk_fmin); + if (!ret) + ret = s5k6aa_write(c, REG_I_MAX_OUTRATE_4KHZ(0), + s5k6aa->pclk_fmax); + if (!ret) + ret = s5k6aa_write(c, REG_I_INIT_PARAMS_UPDATED, 1); + if (!ret) + ret = s5k6aa_read(c, REG_I_ERROR_INFO, &status); + + return ret ? ret : (status ? -EINVAL : 0); +} + +/* Set horizontal and vertical image flipping */ +static int s5k6aa_set_mirror(struct s5k6aa *s5k6aa, int horiz_flip) +{ + struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd); + int index = s5k6aa->preset->index; + + unsigned int vflip = s5k6aa->ctrls.vflip->val ^ s5k6aa->inv_vflip; + unsigned int flip = (horiz_flip ^ s5k6aa->inv_hflip) | (vflip << 1); + + return s5k6aa_write(client, REG_P_PREV_MIRROR(index), flip); +} + +/* Configure auto/manual white balance and R/G/B gains */ +static int s5k6aa_set_awb(struct s5k6aa *s5k6aa, int awb) +{ + struct i2c_client *c = v4l2_get_subdevdata(&s5k6aa->sd); + struct s5k6aa_ctrls *ctrls = &s5k6aa->ctrls; + u16 reg; + + int ret = s5k6aa_read(c, REG_DBG_AUTOALG_EN, ®); + + if (!ret && !awb) { + ret = s5k6aa_write(c, REG_SF_RGAIN, ctrls->gain_red->val); + if (!ret) + ret = s5k6aa_write(c, REG_SF_RGAIN_CHG, 1); + if (ret) + return ret; + + ret = s5k6aa_write(c, REG_SF_GGAIN, ctrls->gain_green->val); + if (!ret) + ret = s5k6aa_write(c, REG_SF_GGAIN_CHG, 1); + if (ret) + return ret; + + ret = s5k6aa_write(c, REG_SF_BGAIN, ctrls->gain_blue->val); + if (!ret) + ret = s5k6aa_write(c, REG_SF_BGAIN_CHG, 1); + } + if (!ret) { + reg = awb ? reg | AALG_WB_EN_MASK : reg & ~AALG_WB_EN_MASK; + ret = s5k6aa_write(c, REG_DBG_AUTOALG_EN, reg); + } + + return ret; +} + +/* Program FW with exposure time, 'exposure' in us units */ +static int s5k6aa_set_user_exposure(struct i2c_client *client, int exposure) +{ + unsigned int time = exposure / 10; + + int ret = s5k6aa_write(client, REG_SF_USR_EXPOSURE_L, time & 0xffff); + if (!ret) + ret = s5k6aa_write(client, REG_SF_USR_EXPOSURE_H, time >> 16); + if (ret) + return ret; + return s5k6aa_write(client, REG_SF_USR_EXPOSURE_CHG, 1); +} + +static int s5k6aa_set_user_gain(struct i2c_client *client, int gain) +{ + int ret = s5k6aa_write(client, REG_SF_USR_TOT_GAIN, gain); + if (ret) + return ret; + return s5k6aa_write(client, REG_SF_USR_TOT_GAIN_CHG, 1); +} + +/* Set auto/manual exposure and total gain */ +static int s5k6aa_set_auto_exposure(struct s5k6aa *s5k6aa, int value) +{ + struct i2c_client *c = v4l2_get_subdevdata(&s5k6aa->sd); + unsigned int exp_time = s5k6aa->ctrls.exposure->val; + u16 auto_alg; + + int ret = s5k6aa_read(c, REG_DBG_AUTOALG_EN, &auto_alg); + if (ret) + return ret; + + v4l2_dbg(1, debug, c, "man_exp: %d, auto_exp: %d, a_alg: 0x%x\n", + exp_time, value, auto_alg); + + if (value == V4L2_EXPOSURE_AUTO) { + auto_alg |= AALG_AE_EN_MASK | AALG_DIVLEI_EN_MASK; + } else { + ret = s5k6aa_set_user_exposure(c, exp_time); + if (ret) + return ret; + ret = s5k6aa_set_user_gain(c, s5k6aa->ctrls.gain->val); + if (ret) + return ret; + auto_alg &= ~(AALG_AE_EN_MASK | AALG_DIVLEI_EN_MASK); + } + + return s5k6aa_write(c, REG_DBG_AUTOALG_EN, auto_alg); +} + +static int s5k6aa_set_anti_flicker(struct s5k6aa *s5k6aa, int value) +{ + struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd); + u16 auto_alg; + int ret; + + ret = s5k6aa_read(client, REG_DBG_AUTOALG_EN, &auto_alg); + if (ret) + return ret; + + if (value == V4L2_CID_POWER_LINE_FREQUENCY_AUTO) { + auto_alg |= AALG_FLICKER_EN_MASK; + } else { + auto_alg &= ~AALG_FLICKER_EN_MASK; + /* The V4L2_CID_LINE_FREQUENCY control values match + * the register values */ + ret = s5k6aa_write(client, REG_SF_FLICKER_QUANT, value); + if (ret) + return ret; + ret = s5k6aa_write(client, REG_SF_FLICKER_QUANT_CHG, 1); + if (ret) + return ret; + } + + return s5k6aa_write(client, REG_DBG_AUTOALG_EN, auto_alg); +} + +static int s5k6aa_set_colorfx(struct s5k6aa *s5k6aa, int val) +{ + struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd); + static const struct v4l2_control colorfx[] = { + { V4L2_COLORFX_NONE, 0 }, + { V4L2_COLORFX_BW, 1 }, + { V4L2_COLORFX_NEGATIVE, 2 }, + { V4L2_COLORFX_SEPIA, 3 }, + { V4L2_COLORFX_SKY_BLUE, 4 }, + { V4L2_COLORFX_SKETCH, 5 }, + }; + int i; + + for (i = 0; i < ARRAY_SIZE(colorfx); i++) { + if (colorfx[i].id == val) + return s5k6aa_write(client, REG_G_SPEC_EFFECTS, + colorfx[i].value); + } + return -EINVAL; +} + +static int s5k6aa_preview_config_status(struct i2c_client *client) +{ + u16 error = 0; + int ret = s5k6aa_read(client, REG_G_PREV_CFG_ERROR, &error); + + v4l2_dbg(1, debug, client, "error: 0x%x (%d)\n", error, ret); + return ret ? ret : (error ? -EINVAL : 0); +} + +static int s5k6aa_get_pixfmt_index(struct s5k6aa *s5k6aa, + struct v4l2_mbus_framefmt *mf) +{ + unsigned int i; + + for (i = 0; i < ARRAY_SIZE(s5k6aa_formats); i++) + if (mf->colorspace == s5k6aa_formats[i].colorspace && + mf->code == s5k6aa_formats[i].code) + return i; + return 0; +} + +static int s5k6aa_set_output_framefmt(struct s5k6aa *s5k6aa, + struct s5k6aa_preset *preset) +{ + struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd); + int fmt_index = s5k6aa_get_pixfmt_index(s5k6aa, &preset->mbus_fmt); + int ret; + + ret = s5k6aa_write(client, REG_P_OUT_WIDTH(preset->index), + preset->mbus_fmt.width); + if (!ret) + ret = s5k6aa_write(client, REG_P_OUT_HEIGHT(preset->index), + preset->mbus_fmt.height); + if (!ret) + ret = s5k6aa_write(client, REG_P_FMT(preset->index), + s5k6aa_formats[fmt_index].reg_p_fmt); + return ret; +} + +static int s5k6aa_set_input_params(struct s5k6aa *s5k6aa) +{ + struct i2c_client *c = v4l2_get_subdevdata(&s5k6aa->sd); + struct v4l2_rect *r = &s5k6aa->ccd_rect; + int ret; + + ret = s5k6aa_write(c, REG_G_PREVZOOM_IN_WIDTH, r->width); + if (!ret) + ret = s5k6aa_write(c, REG_G_PREVZOOM_IN_HEIGHT, r->height); + if (!ret) + ret = s5k6aa_write(c, REG_G_PREVZOOM_IN_XOFFS, r->left); + if (!ret) + ret = s5k6aa_write(c, REG_G_PREVZOOM_IN_YOFFS, r->top); + if (!ret) + ret = s5k6aa_write(c, REG_G_INPUTS_CHANGE_REQ, 1); + if (!ret) + s5k6aa->apply_crop = 0; + + return ret; +} + +/** + * s5k6aa_configure_video_bus - configure the video output interface + * @bus_type: video bus type: parallel or MIPI-CSI + * @nlanes: number of MIPI lanes to be used (MIPI-CSI only) + * + * Note: Only parallel bus operation has been tested. + */ +static int s5k6aa_configure_video_bus(struct s5k6aa *s5k6aa, + enum v4l2_mbus_type bus_type, int nlanes) +{ + struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd); + u16 cfg = 0; + int ret; + + /* + * TODO: The sensor is supposed to support BT.601 and BT.656 + * but there is nothing indicating how to switch between both + * in the datasheet. For now default BT.601 interface is assumed. + */ + if (bus_type == V4L2_MBUS_CSI2) + cfg = nlanes; + else if (bus_type != V4L2_MBUS_PARALLEL) + return -EINVAL; + + ret = s5k6aa_write(client, REG_OIF_EN_MIPI_LANES, cfg); + if (ret) + return ret; + return s5k6aa_write(client, REG_OIF_CFG_CHG, 1); +} + +/* This function should be called when switching to new user configuration set*/ +static int s5k6aa_new_config_sync(struct i2c_client *client, int timeout, + int cid) +{ + unsigned long end = jiffies + msecs_to_jiffies(timeout); + u16 reg = 1; + int ret; + + ret = s5k6aa_write(client, REG_G_ACTIVE_PREV_CFG, cid); + if (!ret) + ret = s5k6aa_write(client, REG_G_PREV_CFG_CHG, 1); + if (!ret) + ret = s5k6aa_write(client, REG_G_NEW_CFG_SYNC, 1); + if (timeout == 0) + return ret; + + while (ret >= 0 && time_is_after_jiffies(end)) { + ret = s5k6aa_read(client, REG_G_NEW_CFG_SYNC, ®); + if (!reg) + return 0; + usleep_range(1000, 5000); + } + return ret ? ret : -ETIMEDOUT; +} + +/** + * s5k6aa_set_prev_config - write user preview register set + * + * Configure output resolution and color fromat, pixel clock + * frequency range, device frame rate type and frame period range. + */ +static int s5k6aa_set_prev_config(struct s5k6aa *s5k6aa, + struct s5k6aa_preset *preset) +{ + struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd); + int idx = preset->index; + u16 frame_rate_q; + int ret; + + if (s5k6aa->fiv->reg_fr_time >= S5K6AA_MAX_HIGHRES_FR_TIME) + frame_rate_q = FR_RATE_Q_BEST_FRRATE; + else + frame_rate_q = FR_RATE_Q_BEST_QUALITY; + + ret = s5k6aa_set_output_framefmt(s5k6aa, preset); + if (!ret) + ret = s5k6aa_write(client, REG_P_MAX_OUT_RATE(idx), + s5k6aa->pclk_fmax); + if (!ret) + ret = s5k6aa_write(client, REG_P_MIN_OUT_RATE(idx), + s5k6aa->pclk_fmin); + if (!ret) + ret = s5k6aa_write(client, REG_P_CLK_INDEX(idx), + preset->clk_id); + if (!ret) + ret = s5k6aa_write(client, REG_P_FR_RATE_TYPE(idx), + FR_RATE_DYNAMIC); + if (!ret) + ret = s5k6aa_write(client, REG_P_FR_RATE_Q_TYPE(idx), + frame_rate_q); + if (!ret) + ret = s5k6aa_write(client, REG_P_MAX_FR_TIME(idx), + s5k6aa->fiv->reg_fr_time + 33); + if (!ret) + ret = s5k6aa_write(client, REG_P_MIN_FR_TIME(idx), + s5k6aa->fiv->reg_fr_time - 33); + if (!ret) + ret = s5k6aa_new_config_sync(client, 250, idx); + if (!ret) + ret = s5k6aa_preview_config_status(client); + if (!ret) + s5k6aa->apply_cfg = 0; + + v4l2_dbg(1, debug, client, "Frame interval: %d +/- 3.3ms. (%d)\n", + s5k6aa->fiv->reg_fr_time, ret); + return ret; +} + +/** + * s5k6aa_initialize_isp - basic ISP MCU initialization + * + * Configure AHB addresses for registers read/write; configure PLLs for + * required output pixel clock. The ISP power supply needs to be already + * enabled, with an optional H/W reset. + * Locking: called with s5k6aa.lock mutex held. + */ +static int s5k6aa_initialize_isp(struct v4l2_subdev *sd) +{ + struct i2c_client *client = v4l2_get_subdevdata(sd); + struct s5k6aa *s5k6aa = to_s5k6aa(sd); + int ret; + + s5k6aa->apply_crop = 1; + s5k6aa->apply_cfg = 1; + msleep(100); + + ret = s5k6aa_set_ahb_address(client); + if (ret) + return ret; + ret = s5k6aa_configure_video_bus(s5k6aa, s5k6aa->bus_type, + s5k6aa->mipi_lanes); + if (ret) + return ret; + ret = s5k6aa_write_array(sd, s5k6aa_analog_config); + if (ret) + return ret; + msleep(20); + + return s5k6aa_configure_pixel_clocks(s5k6aa); +} + +static int s5k6aa_gpio_set_value(struct s5k6aa *priv, int id, u32 val) +{ + if (!gpio_is_valid(priv->gpio[id].gpio)) + return 0; + gpio_set_value(priv->gpio[id].gpio, !!val); + return 1; +} + +static int s5k6aa_gpio_assert(struct s5k6aa *priv, int id) +{ + return s5k6aa_gpio_set_value(priv, id, priv->gpio[id].level); +} + +static int s5k6aa_gpio_deassert(struct s5k6aa *priv, int id) +{ + return s5k6aa_gpio_set_value(priv, id, !priv->gpio[id].level); +} + +static int __s5k6aa_power_on(struct s5k6aa *s5k6aa) +{ + int ret; + + ret = regulator_bulk_enable(S5K6AA_NUM_SUPPLIES, s5k6aa->supplies); + if (ret) + return ret; + if (s5k6aa_gpio_deassert(s5k6aa, STBY)) + usleep_range(150, 200); + + if (s5k6aa->s_power) + ret = s5k6aa->s_power(1); + usleep_range(4000, 4000); + + if (s5k6aa_gpio_deassert(s5k6aa, RST)) + msleep(20); + + return ret; +} + +static int __s5k6aa_power_off(struct s5k6aa *s5k6aa) +{ + int ret; + + if (s5k6aa_gpio_assert(s5k6aa, RST)) + usleep_range(100, 150); + + if (s5k6aa->s_power) { + ret = s5k6aa->s_power(0); + if (ret) + return ret; + } + if (s5k6aa_gpio_assert(s5k6aa, STBY)) + usleep_range(50, 100); + s5k6aa->streaming = 0; + + return regulator_bulk_disable(S5K6AA_NUM_SUPPLIES, s5k6aa->supplies); +} + +/* + * V4L2 subdev core and video operations + */ +static int s5k6aa_set_power(struct v4l2_subdev *sd, int on) +{ + struct s5k6aa *s5k6aa = to_s5k6aa(sd); + int ret = 0; + + mutex_lock(&s5k6aa->lock); + + if (!on == s5k6aa->power) { + if (on) { + ret = __s5k6aa_power_on(s5k6aa); + if (!ret) + ret = s5k6aa_initialize_isp(sd); + } else { + ret = __s5k6aa_power_off(s5k6aa); + } + + if (!ret) + s5k6aa->power += on ? 1 : -1; + } + + mutex_unlock(&s5k6aa->lock); + + if (!on || ret || s5k6aa->power != 1) + return ret; + + return v4l2_ctrl_handler_setup(sd->ctrl_handler); +} + +static int __s5k6aa_stream(struct s5k6aa *s5k6aa, int enable) +{ + struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd); + int ret = 0; + + ret = s5k6aa_write(client, REG_G_ENABLE_PREV, enable); + if (!ret) + ret = s5k6aa_write(client, REG_G_ENABLE_PREV_CHG, 1); + if (!ret) + s5k6aa->streaming = enable; + + return ret; +} + +static int s5k6aa_s_stream(struct v4l2_subdev *sd, int on) +{ + struct s5k6aa *s5k6aa = to_s5k6aa(sd); + int ret = 0; + + mutex_lock(&s5k6aa->lock); + + if (s5k6aa->streaming == !on) { + if (!ret && s5k6aa->apply_cfg) + ret = s5k6aa_set_prev_config(s5k6aa, s5k6aa->preset); + if (s5k6aa->apply_crop) + ret = s5k6aa_set_input_params(s5k6aa); + if (!ret) + ret = __s5k6aa_stream(s5k6aa, !!on); + } + mutex_unlock(&s5k6aa->lock); + + return ret; +} + +static int s5k6aa_g_frame_interval(struct v4l2_subdev *sd, + struct v4l2_subdev_frame_interval *fi) +{ + struct s5k6aa *s5k6aa = to_s5k6aa(sd); + + mutex_lock(&s5k6aa->lock); + fi->interval = s5k6aa->fiv->interval; + mutex_unlock(&s5k6aa->lock); + + return 0; +} + +static int __s5k6aa_set_frame_interval(struct s5k6aa *s5k6aa, + struct v4l2_subdev_frame_interval *fi) +{ + struct v4l2_mbus_framefmt *mbus_fmt = &s5k6aa->preset->mbus_fmt; + const struct s5k6aa_interval *fiv = &s5k6aa_intervals[0]; + unsigned int err, min_err = UINT_MAX; + unsigned int i, fr_time; + + if (fi->interval.denominator == 0) + return -EINVAL; + + fr_time = fi->interval.numerator * 10000 / fi->interval.denominator; + + for (i = 0; i < ARRAY_SIZE(s5k6aa_intervals); i++) { + const struct s5k6aa_interval *iv = &s5k6aa_intervals[i]; + + if (mbus_fmt->width > iv->size.width || + mbus_fmt->height > iv->size.height) + continue; + + err = abs(iv->reg_fr_time - fr_time); + if (err < min_err) { + fiv = iv; + min_err = err; + } + } + s5k6aa->fiv = fiv; + + v4l2_dbg(1, debug, &s5k6aa->sd, "Changed frame interval to %d us\n", + fiv->reg_fr_time * 100); + return 0; +} + +static int s5k6aa_s_frame_interval(struct v4l2_subdev *sd, + struct v4l2_subdev_frame_interval *fi) +{ + struct s5k6aa *s5k6aa = to_s5k6aa(sd); + int ret; + + v4l2_dbg(1, debug, sd, "Setting %d/%d frame interval\n", + fi->interval.numerator, fi->interval.denominator); + + mutex_lock(&s5k6aa->lock); + ret = __s5k6aa_set_frame_interval(s5k6aa, fi); + s5k6aa->apply_cfg = 1; + + mutex_unlock(&s5k6aa->lock); + return ret; +} + +/* + * V4L2 subdev pad level and video operations + */ +static int s5k6aa_enum_frame_interval(struct v4l2_subdev *sd, + struct v4l2_subdev_fh *fh, + struct v4l2_subdev_frame_interval_enum *fie) +{ + struct s5k6aa *s5k6aa = to_s5k6aa(sd); + const struct s5k6aa_interval *fi; + int ret = 0; + + if (fie->index > ARRAY_SIZE(s5k6aa_intervals)) + return -EINVAL; + + v4l_bound_align_image(&fie->width, S5K6AA_WIN_WIDTH_MIN, + S5K6AA_WIN_WIDTH_MAX, 1, + &fie->height, S5K6AA_WIN_HEIGHT_MIN, + S5K6AA_WIN_HEIGHT_MAX, 1, 0); + + mutex_lock(&s5k6aa->lock); + fi = &s5k6aa_intervals[fie->index]; + if (fie->width > fi->size.width || fie->height > fi->size.height) + ret = -EINVAL; + else + fie->interval = fi->interval; + mutex_unlock(&s5k6aa->lock); + + return ret; +} + +static int s5k6aa_enum_mbus_code(struct v4l2_subdev *sd, + struct v4l2_subdev_fh *fh, + struct v4l2_subdev_mbus_code_enum *code) +{ + if (code->index >= ARRAY_SIZE(s5k6aa_formats)) + return -EINVAL; + + code->code = s5k6aa_formats[code->index].code; + return 0; +} + +static int s5k6aa_enum_frame_size(struct v4l2_subdev *sd, + struct v4l2_subdev_fh *fh, + struct v4l2_subdev_frame_size_enum *fse) +{ + int i = ARRAY_SIZE(s5k6aa_formats); + + if (fse->index > 0) + return -EINVAL; + + while (--i) + if (fse->code == s5k6aa_formats[i].code) + break; + + fse->code = s5k6aa_formats[i].code; + fse->min_width = S5K6AA_WIN_WIDTH_MIN; + fse->max_width = S5K6AA_WIN_WIDTH_MAX; + fse->max_height = S5K6AA_WIN_HEIGHT_MIN; + fse->min_height = S5K6AA_WIN_HEIGHT_MAX; + + return 0; +} + +static struct v4l2_rect * +__s5k6aa_get_crop_rect(struct s5k6aa *s5k6aa, struct v4l2_subdev_fh *fh, + enum v4l2_subdev_format_whence which) +{ + if (which == V4L2_SUBDEV_FORMAT_ACTIVE) + return &s5k6aa->ccd_rect; + + WARN_ON(which != V4L2_SUBDEV_FORMAT_TRY); + return v4l2_subdev_get_try_crop(fh, 0); +} + +static void s5k6aa_try_format(struct s5k6aa *s5k6aa, + struct v4l2_mbus_framefmt *mf) +{ + unsigned int index; + + v4l_bound_align_image(&mf->width, S5K6AA_WIN_WIDTH_MIN, + S5K6AA_WIN_WIDTH_MAX, 1, + &mf->height, S5K6AA_WIN_HEIGHT_MIN, + S5K6AA_WIN_HEIGHT_MAX, 1, 0); + + if (mf->colorspace != V4L2_COLORSPACE_JPEG && + mf->colorspace != V4L2_COLORSPACE_REC709) + mf->colorspace = V4L2_COLORSPACE_JPEG; + + index = s5k6aa_get_pixfmt_index(s5k6aa, mf); + + mf->colorspace = s5k6aa_formats[index].colorspace; + mf->code = s5k6aa_formats[index].code; + mf->field = V4L2_FIELD_NONE; +} + +static int s5k6aa_get_fmt(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh, + struct v4l2_subdev_format *fmt) +{ + struct s5k6aa *s5k6aa = to_s5k6aa(sd); + struct v4l2_mbus_framefmt *mf; + + memset(fmt->reserved, 0, sizeof(fmt->reserved)); + + if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) { + mf = v4l2_subdev_get_try_format(fh, 0); + fmt->format = *mf; + return 0; + } + + mutex_lock(&s5k6aa->lock); + fmt->format = s5k6aa->preset->mbus_fmt; + mutex_unlock(&s5k6aa->lock); + + return 0; +} + +static int s5k6aa_set_fmt(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh, + struct v4l2_subdev_format *fmt) +{ + struct s5k6aa *s5k6aa = to_s5k6aa(sd); + struct s5k6aa_preset *preset = s5k6aa->preset; + struct v4l2_mbus_framefmt *mf; + struct v4l2_rect *crop; + int ret = 0; + + mutex_lock(&s5k6aa->lock); + s5k6aa_try_format(s5k6aa, &fmt->format); + + if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) { + mf = v4l2_subdev_get_try_format(fh, fmt->pad); + crop = v4l2_subdev_get_try_crop(fh, 0); + } else { + if (s5k6aa->streaming) { + ret = -EBUSY; + } else { + mf = &preset->mbus_fmt; + crop = &s5k6aa->ccd_rect; + s5k6aa->apply_cfg = 1; + } + } + + if (ret == 0) { + struct v4l2_subdev_frame_interval fiv = { + .interval = {0, 1} + }; + + *mf = fmt->format; + /* + * Make sure the crop window is valid, i.e. its size is + * greater than the output window, as the ISP supports + * only down-scaling. + */ + crop->width = clamp_t(unsigned int, crop->width, mf->width, + S5K6AA_WIN_WIDTH_MAX); + crop->height = clamp_t(unsigned int, crop->height, mf->height, + S5K6AA_WIN_HEIGHT_MAX); + crop->left = clamp_t(unsigned int, crop->left, 0, + S5K6AA_WIN_WIDTH_MAX - crop->width); + crop->top = clamp_t(unsigned int, crop->top, 0, + S5K6AA_WIN_HEIGHT_MAX - crop->height); + + /* Reset to minimum possible frame interval */ + ret = __s5k6aa_set_frame_interval(s5k6aa, &fiv); + } + mutex_unlock(&s5k6aa->lock); + + return ret; +} + +static int s5k6aa_get_crop(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh, + struct v4l2_subdev_crop *crop) +{ + struct s5k6aa *s5k6aa = to_s5k6aa(sd); + struct v4l2_rect *rect; + + memset(crop->reserved, 0, sizeof(crop->reserved)); + + mutex_lock(&s5k6aa->lock); + rect = __s5k6aa_get_crop_rect(s5k6aa, fh, crop->which); + crop->rect = *rect; + mutex_unlock(&s5k6aa->lock); + + v4l2_dbg(1, debug, sd, "Current crop rectangle: (%d,%d)/%dx%d\n", + rect->left, rect->top, rect->width, rect->height); + + return 0; +} + +static int s5k6aa_set_crop(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh, + struct v4l2_subdev_crop *crop) +{ + struct s5k6aa *s5k6aa = to_s5k6aa(sd); + struct v4l2_mbus_framefmt *mf; + unsigned int max_x, max_y; + struct v4l2_rect *crop_r; + + mutex_lock(&s5k6aa->lock); + crop_r = __s5k6aa_get_crop_rect(s5k6aa, fh, crop->which); + + if (crop->which == V4L2_SUBDEV_FORMAT_ACTIVE) { + mf = &s5k6aa->preset->mbus_fmt; + s5k6aa->apply_crop = 1; + } else { + mf = v4l2_subdev_get_try_format(fh, 0); + } + v4l_bound_align_image(&crop->rect.width, mf->width, + S5K6AA_WIN_WIDTH_MAX, 1, + &crop->rect.height, mf->height, + S5K6AA_WIN_HEIGHT_MAX, 1, 0); + + max_x = (S5K6AA_WIN_WIDTH_MAX - crop->rect.width) & ~1; + max_y = (S5K6AA_WIN_HEIGHT_MAX - crop->rect.height) & ~1; + + crop->rect.left = clamp_t(unsigned int, crop->rect.left, 0, max_x); + crop->rect.top = clamp_t(unsigned int, crop->rect.top, 0, max_y); + + *crop_r = crop->rect; + + mutex_unlock(&s5k6aa->lock); + + v4l2_dbg(1, debug, sd, "Set crop rectangle: (%d,%d)/%dx%d\n", + crop_r->left, crop_r->top, crop_r->width, crop_r->height); + + return 0; +} + +static const struct v4l2_subdev_pad_ops s5k6aa_pad_ops = { + .enum_mbus_code = s5k6aa_enum_mbus_code, + .enum_frame_size = s5k6aa_enum_frame_size, + .enum_frame_interval = s5k6aa_enum_frame_interval, + .get_fmt = s5k6aa_get_fmt, + .set_fmt = s5k6aa_set_fmt, + .get_crop = s5k6aa_get_crop, + .set_crop = s5k6aa_set_crop, +}; + +static const struct v4l2_subdev_video_ops s5k6aa_video_ops = { + .g_frame_interval = s5k6aa_g_frame_interval, + .s_frame_interval = s5k6aa_s_frame_interval, + .s_stream = s5k6aa_s_stream, +}; + +/* + * V4L2 subdev controls + */ + +static int s5k6aa_s_ctrl(struct v4l2_ctrl *ctrl) +{ + struct v4l2_subdev *sd = ctrl_to_sd(ctrl); + struct i2c_client *client = v4l2_get_subdevdata(sd); + struct s5k6aa *s5k6aa = to_s5k6aa(sd); + int idx, err = 0; + + v4l2_dbg(1, debug, sd, "ctrl: 0x%x, value: %d\n", ctrl->id, ctrl->val); + + mutex_lock(&s5k6aa->lock); + /* + * If the device is not powered up by the host driver do + * not apply any controls to H/W at this time. Instead + * the controls will be restored right after power-up. + */ + if (s5k6aa->power == 0) + goto unlock; + idx = s5k6aa->preset->index; + + switch (ctrl->id) { + case V4L2_CID_AUTO_WHITE_BALANCE: + err = s5k6aa_set_awb(s5k6aa, ctrl->val); + break; + + case V4L2_CID_BRIGHTNESS: + err = s5k6aa_write(client, REG_USER_BRIGHTNESS, ctrl->val); + break; + + case V4L2_CID_COLORFX: + err = s5k6aa_set_colorfx(s5k6aa, ctrl->val); + break; + + case V4L2_CID_CONTRAST: + err = s5k6aa_write(client, REG_USER_CONTRAST, ctrl->val); + break; + + case V4L2_CID_EXPOSURE_AUTO: + err = s5k6aa_set_auto_exposure(s5k6aa, ctrl->val); + break; + + case V4L2_CID_HFLIP: + err = s5k6aa_set_mirror(s5k6aa, ctrl->val); + if (err) + break; + err = s5k6aa_write(client, REG_G_PREV_CFG_CHG, 1); + break; + + case V4L2_CID_POWER_LINE_FREQUENCY: + err = s5k6aa_set_anti_flicker(s5k6aa, ctrl->val); + break; + + case V4L2_CID_SATURATION: + err = s5k6aa_write(client, REG_USER_SATURATION, ctrl->val); + break; + + case V4L2_CID_SHARPNESS: + err = s5k6aa_write(client, REG_USER_SHARPBLUR, ctrl->val); + break; + + case V4L2_CID_WHITE_BALANCE_TEMPERATURE: + err = s5k6aa_write(client, REG_P_COLORTEMP(idx), ctrl->val); + if (err) + break; + err = s5k6aa_write(client, REG_G_PREV_CFG_CHG, 1); + break; + } +unlock: + mutex_unlock(&s5k6aa->lock); + return err; +} + +static const struct v4l2_ctrl_ops s5k6aa_ctrl_ops = { + .s_ctrl = s5k6aa_s_ctrl, +}; + +static int s5k6aa_log_status(struct v4l2_subdev *sd) +{ + v4l2_ctrl_handler_log_status(sd->ctrl_handler, sd->name); + return 0; +} + +#define V4L2_CID_RED_GAIN (V4L2_CTRL_CLASS_CAMERA | 0x1001) +#define V4L2_CID_GREEN_GAIN (V4L2_CTRL_CLASS_CAMERA | 0x1002) +#define V4L2_CID_BLUE_GAIN (V4L2_CTRL_CLASS_CAMERA | 0x1003) + +static const struct v4l2_ctrl_config s5k6aa_ctrls[] = { + { + .ops = &s5k6aa_ctrl_ops, + .id = V4L2_CID_RED_GAIN, + .type = V4L2_CTRL_TYPE_INTEGER, + .name = "Gain, Red", + .min = 0, + .max = 256, + .def = 127, + .step = 1, + }, { + .ops = &s5k6aa_ctrl_ops, + .id = V4L2_CID_GREEN_GAIN, + .type = V4L2_CTRL_TYPE_INTEGER, + .name = "Gain, Green", + .min = 0, + .max = 256, + .def = 127, + .step = 1, + }, { + .ops = &s5k6aa_ctrl_ops, + .id = V4L2_CID_BLUE_GAIN, + .type = V4L2_CTRL_TYPE_INTEGER, + .name = "Gain, Blue", + .min = 0, + .max = 256, + .def = 127, + .step = 1, + }, +}; + +static int s5k6aa_initialize_ctrls(struct s5k6aa *s5k6aa) +{ + const struct v4l2_ctrl_ops *ops = &s5k6aa_ctrl_ops; + struct s5k6aa_ctrls *ctrls = &s5k6aa->ctrls; + struct v4l2_ctrl_handler *hdl = &ctrls->handler; + + int ret = v4l2_ctrl_handler_init(hdl, 16); + if (ret) + return ret; + /* Auto white balance cluster */ + ctrls->awb = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_AUTO_WHITE_BALANCE, + 0, 1, 1, 1); + ctrls->gain_red = v4l2_ctrl_new_custom(hdl, &s5k6aa_ctrls[0], NULL); + ctrls->gain_green = v4l2_ctrl_new_custom(hdl, &s5k6aa_ctrls[1], NULL); + ctrls->gain_blue = v4l2_ctrl_new_custom(hdl, &s5k6aa_ctrls[2], NULL); + v4l2_ctrl_auto_cluster(4, &ctrls->awb, 0, false); + + ctrls->hflip = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_HFLIP, 0, 1, 1, 0); + ctrls->vflip = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_VFLIP, 0, 1, 1, 0); + v4l2_ctrl_cluster(2, &ctrls->hflip); + + ctrls->auto_exp = v4l2_ctrl_new_std_menu(hdl, ops, + V4L2_CID_EXPOSURE_AUTO, + V4L2_EXPOSURE_MANUAL, 0, V4L2_EXPOSURE_AUTO); + /* Exposure time: x 1 us */ + ctrls->exposure = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_EXPOSURE, + 0, 6000000U, 1, 100000U); + /* Total gain: 256 <=> 1x */ + ctrls->gain = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_GAIN, + 0, 256, 1, 256); + v4l2_ctrl_auto_cluster(3, &ctrls->auto_exp, 0, false); + + v4l2_ctrl_new_std_menu(hdl, ops, V4L2_CID_POWER_LINE_FREQUENCY, + V4L2_CID_POWER_LINE_FREQUENCY_AUTO, 0, + V4L2_CID_POWER_LINE_FREQUENCY_AUTO); + + v4l2_ctrl_new_std_menu(hdl, ops, V4L2_CID_COLORFX, + V4L2_COLORFX_SKY_BLUE, ~0x6f, V4L2_COLORFX_NONE); + + v4l2_ctrl_new_std(hdl, ops, V4L2_CID_WHITE_BALANCE_TEMPERATURE, + 0, 256, 1, 0); + + v4l2_ctrl_new_std(hdl, ops, V4L2_CID_SATURATION, -127, 127, 1, 0); + v4l2_ctrl_new_std(hdl, ops, V4L2_CID_BRIGHTNESS, -127, 127, 1, 0); + v4l2_ctrl_new_std(hdl, ops, V4L2_CID_CONTRAST, -127, 127, 1, 0); + v4l2_ctrl_new_std(hdl, ops, V4L2_CID_SHARPNESS, -127, 127, 1, 0); + + if (hdl->error) { + ret = hdl->error; + v4l2_ctrl_handler_free(hdl); + return ret; + } + + s5k6aa->sd.ctrl_handler = hdl; + return 0; +} + +/* + * V4L2 subdev internal operations + */ +static int s5k6aa_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh) +{ + struct v4l2_mbus_framefmt *format = v4l2_subdev_get_try_format(fh, 0); + struct v4l2_rect *crop = v4l2_subdev_get_try_crop(fh, 0); + + format->colorspace = s5k6aa_formats[0].colorspace; + format->code = s5k6aa_formats[0].code; + format->width = S5K6AA_OUT_WIDTH_DEF; + format->height = S5K6AA_OUT_HEIGHT_DEF; + format->field = V4L2_FIELD_NONE; + + crop->width = S5K6AA_WIN_WIDTH_MAX; + crop->height = S5K6AA_WIN_HEIGHT_MAX; + crop->left = 0; + crop->top = 0; + + return 0; +} + +static int s5k6aa_check_fw_revision(struct s5k6aa *s5k6aa) +{ + struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd); + u16 api_ver = 0, fw_rev = 0; + + int ret = s5k6aa_set_ahb_address(client); + + if (!ret) + ret = s5k6aa_read(client, REG_FW_APIVER, &api_ver); + if (!ret) + ret = s5k6aa_read(client, REG_FW_REVISION, &fw_rev); + if (ret) { + v4l2_err(&s5k6aa->sd, "FW revision check failed!\n"); + return ret; + } + + v4l2_info(&s5k6aa->sd, "FW API ver.: 0x%X, FW rev.: 0x%X\n", + api_ver, fw_rev); + + return api_ver == S5K6AAFX_FW_APIVER ? 0 : -ENODEV; +} + +static int s5k6aa_registered(struct v4l2_subdev *sd) +{ + struct s5k6aa *s5k6aa = to_s5k6aa(sd); + int ret; + + mutex_lock(&s5k6aa->lock); + ret = __s5k6aa_power_on(s5k6aa); + if (!ret) { + msleep(100); + ret = s5k6aa_check_fw_revision(s5k6aa); + __s5k6aa_power_off(s5k6aa); + } + mutex_unlock(&s5k6aa->lock); + + return ret; +} + +static const struct v4l2_subdev_internal_ops s5k6aa_subdev_internal_ops = { + .registered = s5k6aa_registered, + .open = s5k6aa_open, +}; + +static const struct v4l2_subdev_core_ops s5k6aa_core_ops = { + .s_power = s5k6aa_set_power, + .log_status = s5k6aa_log_status, +}; + +static const struct v4l2_subdev_ops s5k6aa_subdev_ops = { + .core = &s5k6aa_core_ops, + .pad = &s5k6aa_pad_ops, + .video = &s5k6aa_video_ops, +}; + +/* + * GPIO setup + */ +static int s5k6aa_configure_gpio(int nr, int val, const char *name) +{ + unsigned long flags = val ? GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW; + int ret; + + if (!gpio_is_valid(nr)) + return 0; + ret = gpio_request_one(nr, flags, name); + if (!ret) + gpio_export(nr, 0); + return ret; +} + +static void s5k6aa_free_gpios(struct s5k6aa *s5k6aa) +{ + int i; + + for (i = 0; i < ARRAY_SIZE(s5k6aa->gpio); i++) { + if (!gpio_is_valid(s5k6aa->gpio[i].gpio)) + continue; + gpio_free(s5k6aa->gpio[i].gpio); + s5k6aa->gpio[i].gpio = -EINVAL; + } +} + +static int s5k6aa_configure_gpios(struct s5k6aa *s5k6aa, + const struct s5k6aa_platform_data *pdata) +{ + const struct s5k6aa_gpio *gpio = &pdata->gpio_stby; + int ret; + + s5k6aa->gpio[STBY].gpio = -EINVAL; + s5k6aa->gpio[RST].gpio = -EINVAL; + + ret = s5k6aa_configure_gpio(gpio->gpio, gpio->level, "S5K6AA_STBY"); + if (ret) { + s5k6aa_free_gpios(s5k6aa); + return ret; + } + s5k6aa->gpio[STBY] = *gpio; + if (gpio_is_valid(gpio->gpio)) + gpio_set_value(gpio->gpio, 0); + + gpio = &pdata->gpio_reset; + ret = s5k6aa_configure_gpio(gpio->gpio, gpio->level, "S5K6AA_RST"); + if (ret) { + s5k6aa_free_gpios(s5k6aa); + return ret; + } + s5k6aa->gpio[RST] = *gpio; + if (gpio_is_valid(gpio->gpio)) + gpio_set_value(gpio->gpio, 0); + + return 0; +} + +static int s5k6aa_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + const struct s5k6aa_platform_data *pdata = client->dev.platform_data; + struct v4l2_subdev *sd; + struct s5k6aa *s5k6aa; + int i, ret; + + if (pdata == NULL) { + dev_err(&client->dev, "Platform data not specified\n"); + return -EINVAL; + } + + if (pdata->mclk_frequency == 0) { + dev_err(&client->dev, "MCLK frequency not specified\n"); + return -EINVAL; + } + + s5k6aa = devm_kzalloc(&client->dev, sizeof(*s5k6aa), GFP_KERNEL); + if (!s5k6aa) + return -ENOMEM; + + mutex_init(&s5k6aa->lock); + + s5k6aa->mclk_frequency = pdata->mclk_frequency; + s5k6aa->bus_type = pdata->bus_type; + s5k6aa->mipi_lanes = pdata->nlanes; + s5k6aa->s_power = pdata->set_power; + s5k6aa->inv_hflip = pdata->horiz_flip; + s5k6aa->inv_vflip = pdata->vert_flip; + + sd = &s5k6aa->sd; + v4l2_i2c_subdev_init(sd, client, &s5k6aa_subdev_ops); + strlcpy(sd->name, DRIVER_NAME, sizeof(sd->name)); + + sd->internal_ops = &s5k6aa_subdev_internal_ops; + sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; + + s5k6aa->pad.flags = MEDIA_PAD_FL_SOURCE; + sd->entity.type = MEDIA_ENT_T_V4L2_SUBDEV_SENSOR; + ret = media_entity_init(&sd->entity, 1, &s5k6aa->pad, 0); + if (ret) + return ret; + + ret = s5k6aa_configure_gpios(s5k6aa, pdata); + if (ret) + goto out_err2; + + for (i = 0; i < S5K6AA_NUM_SUPPLIES; i++) + s5k6aa->supplies[i].supply = s5k6aa_supply_names[i]; + + ret = regulator_bulk_get(&client->dev, S5K6AA_NUM_SUPPLIES, + s5k6aa->supplies); + if (ret) { + dev_err(&client->dev, "Failed to get regulators\n"); + goto out_err3; + } + + ret = s5k6aa_initialize_ctrls(s5k6aa); + if (ret) + goto out_err4; + + s5k6aa_presets_data_init(s5k6aa); + + s5k6aa->ccd_rect.width = S5K6AA_WIN_WIDTH_MAX; + s5k6aa->ccd_rect.height = S5K6AA_WIN_HEIGHT_MAX; + s5k6aa->ccd_rect.left = 0; + s5k6aa->ccd_rect.top = 0; + + return 0; + +out_err4: + regulator_bulk_free(S5K6AA_NUM_SUPPLIES, s5k6aa->supplies); +out_err3: + s5k6aa_free_gpios(s5k6aa); +out_err2: + media_entity_cleanup(&s5k6aa->sd.entity); + return ret; +} + +static int s5k6aa_remove(struct i2c_client *client) +{ + struct v4l2_subdev *sd = i2c_get_clientdata(client); + struct s5k6aa *s5k6aa = to_s5k6aa(sd); + + v4l2_device_unregister_subdev(sd); + v4l2_ctrl_handler_free(sd->ctrl_handler); + media_entity_cleanup(&sd->entity); + regulator_bulk_free(S5K6AA_NUM_SUPPLIES, s5k6aa->supplies); + s5k6aa_free_gpios(s5k6aa); + + return 0; +} + +static const struct i2c_device_id s5k6aa_id[] = { + { DRIVER_NAME, 0 }, + { }, +}; +MODULE_DEVICE_TABLE(i2c, s5k6aa_id); + + +static struct i2c_driver s5k6aa_i2c_driver = { + .driver = { + .name = DRIVER_NAME + }, + .probe = s5k6aa_probe, + .remove = s5k6aa_remove, + .id_table = s5k6aa_id, +}; + +module_i2c_driver(s5k6aa_i2c_driver); + +MODULE_DESCRIPTION("Samsung S5K6AA(FX) SXGA camera driver"); +MODULE_AUTHOR("Sylwester Nawrocki <s.nawrocki@samsung.com>"); +MODULE_LICENSE("GPL"); |