diff options
Diffstat (limited to 'drivers/mmc/host/au1xmmc.c')
| -rw-r--r-- | drivers/mmc/host/au1xmmc.c | 792 |
1 files changed, 469 insertions, 323 deletions
diff --git a/drivers/mmc/host/au1xmmc.c b/drivers/mmc/host/au1xmmc.c index cc5f7bc546a..3f15eb20489 100644 --- a/drivers/mmc/host/au1xmmc.c +++ b/drivers/mmc/host/au1xmmc.c @@ -21,7 +21,7 @@ * published by the Free Software Foundation. */ -/* Why is a timer used to detect insert events? +/* Why don't we use the SD controllers' carddetect feature? * * From the AU1100 MMC application guide: * If the Au1100-based design is intended to support both MultiMediaCards @@ -30,8 +30,6 @@ * In doing so, a MMC card never enters SPI-mode communications, * but now the SecureDigital card-detect feature of CD/DAT3 is ineffective * (the low to high transition will not occur). - * - * So we use the timer to check the status manually. */ #include <linux/module.h> @@ -41,51 +39,110 @@ #include <linux/interrupt.h> #include <linux/dma-mapping.h> #include <linux/scatterlist.h> - +#include <linux/leds.h> #include <linux/mmc/host.h> + #include <asm/io.h> #include <asm/mach-au1x00/au1000.h> #include <asm/mach-au1x00/au1xxx_dbdma.h> #include <asm/mach-au1x00/au1100_mmc.h> -#include <au1xxx.h> -#include "au1xmmc.h" - #define DRIVER_NAME "au1xxx-mmc" /* Set this to enable special debugging macros */ +/* #define DEBUG */ #ifdef DEBUG -#define DBG(fmt, idx, args...) printk("au1xx(%d): DEBUG: " fmt, idx, ##args) +#define DBG(fmt, idx, args...) \ + printk(KERN_DEBUG "au1xmmc(%d): DEBUG: " fmt, idx, ##args) #else -#define DBG(fmt, idx, args...) +#define DBG(fmt, idx, args...) do {} while (0) #endif -const struct { +/* Hardware definitions */ +#define AU1XMMC_DESCRIPTOR_COUNT 1 +#define AU1XMMC_DESCRIPTOR_SIZE 2048 + +#define AU1XMMC_OCR (MMC_VDD_27_28 | MMC_VDD_28_29 | MMC_VDD_29_30 | \ + MMC_VDD_30_31 | MMC_VDD_31_32 | MMC_VDD_32_33 | \ + MMC_VDD_33_34 | MMC_VDD_34_35 | MMC_VDD_35_36) + +/* This gives us a hard value for the stop command that we can write directly + * to the command register. + */ +#define STOP_CMD \ + (SD_CMD_RT_1B | SD_CMD_CT_7 | (0xC << SD_CMD_CI_SHIFT) | SD_CMD_GO) + +/* This is the set of interrupts that we configure by default. */ +#define AU1XMMC_INTERRUPTS \ + (SD_CONFIG_SC | SD_CONFIG_DT | SD_CONFIG_RAT | \ + SD_CONFIG_CR | SD_CONFIG_I) + +/* The poll event (looking for insert/remove events runs twice a second. */ +#define AU1XMMC_DETECT_TIMEOUT (HZ/2) + +struct au1xmmc_host { + struct mmc_host *mmc; + struct mmc_request *mrq; + + u32 flags; u32 iobase; - u32 tx_devid, rx_devid; - u16 bcsrpwr; - u16 bcsrstatus; - u16 wpstatus; -} au1xmmc_card_table[] = { - { SD0_BASE, DSCR_CMD0_SDMS_TX0, DSCR_CMD0_SDMS_RX0, - BCSR_BOARD_SD0PWR, BCSR_INT_SD0INSERT, BCSR_STATUS_SD0WP }, -#ifndef CONFIG_MIPS_DB1200 - { SD1_BASE, DSCR_CMD0_SDMS_TX1, DSCR_CMD0_SDMS_RX1, - BCSR_BOARD_DS1PWR, BCSR_INT_SD1INSERT, BCSR_STATUS_SD1WP } -#endif -}; + u32 clock; + u32 bus_width; + u32 power_mode; -#define AU1XMMC_CONTROLLER_COUNT (ARRAY_SIZE(au1xmmc_card_table)) + int status; -/* This array stores pointers for the hosts (used by the IRQ handler) */ -struct au1xmmc_host *au1xmmc_hosts[AU1XMMC_CONTROLLER_COUNT]; -static int dma = 1; + struct { + int len; + int dir; + } dma; -#ifdef MODULE -module_param(dma, bool, 0); -MODULE_PARM_DESC(dma, "Use DMA engine for data transfers (0 = disabled)"); -#endif + struct { + int index; + int offset; + int len; + } pio; + + u32 tx_chan; + u32 rx_chan; + + int irq; + + struct tasklet_struct finish_task; + struct tasklet_struct data_task; + struct au1xmmc_platform_data *platdata; + struct platform_device *pdev; + struct resource *ioarea; +}; + +/* Status flags used by the host structure */ +#define HOST_F_XMIT 0x0001 +#define HOST_F_RECV 0x0002 +#define HOST_F_DMA 0x0010 +#define HOST_F_ACTIVE 0x0100 +#define HOST_F_STOP 0x1000 + +#define HOST_S_IDLE 0x0001 +#define HOST_S_CMD 0x0002 +#define HOST_S_DATA 0x0003 +#define HOST_S_STOP 0x0004 + +/* Easy access macros */ +#define HOST_STATUS(h) ((h)->iobase + SD_STATUS) +#define HOST_CONFIG(h) ((h)->iobase + SD_CONFIG) +#define HOST_ENABLE(h) ((h)->iobase + SD_ENABLE) +#define HOST_TXPORT(h) ((h)->iobase + SD_TXPORT) +#define HOST_RXPORT(h) ((h)->iobase + SD_RXPORT) +#define HOST_CMDARG(h) ((h)->iobase + SD_CMDARG) +#define HOST_BLKSIZE(h) ((h)->iobase + SD_BLKSIZE) +#define HOST_CMD(h) ((h)->iobase + SD_CMD) +#define HOST_CONFIG2(h) ((h)->iobase + SD_CONFIG2) +#define HOST_TIMEOUT(h) ((h)->iobase + SD_TIMEOUT) +#define HOST_DEBUG(h) ((h)->iobase + SD_DEBUG) + +#define DMA_CHANNEL(h) \ + (((h)->flags & HOST_F_XMIT) ? (h)->tx_chan : (h)->rx_chan) static inline void IRQ_ON(struct au1xmmc_host *host, u32 mask) { @@ -119,14 +176,13 @@ static inline void IRQ_OFF(struct au1xmmc_host *host, u32 mask) static inline void SEND_STOP(struct au1xmmc_host *host) { - - /* We know the value of CONFIG2, so avoid a read we don't need */ - u32 mask = SD_CONFIG2_EN; + u32 config2; WARN_ON(host->status != HOST_S_DATA); host->status = HOST_S_STOP; - au_writel(mask | SD_CONFIG2_DF, HOST_CONFIG2(host)); + config2 = au_readl(HOST_CONFIG2(host)); + au_writel(config2 | SD_CONFIG2_DF, HOST_CONFIG2(host)); au_sync(); /* Send the stop commmand */ @@ -135,35 +191,36 @@ static inline void SEND_STOP(struct au1xmmc_host *host) static void au1xmmc_set_power(struct au1xmmc_host *host, int state) { - - u32 val = au1xmmc_card_table[host->id].bcsrpwr; - - bcsr->board &= ~val; - if (state) bcsr->board |= val; - - au_sync_delay(1); + if (host->platdata && host->platdata->set_power) + host->platdata->set_power(host->mmc, state); } -static inline int au1xmmc_card_inserted(struct au1xmmc_host *host) +static int au1xmmc_card_inserted(struct mmc_host *mmc) { - return (bcsr->sig_status & au1xmmc_card_table[host->id].bcsrstatus) - ? 1 : 0; + struct au1xmmc_host *host = mmc_priv(mmc); + + if (host->platdata && host->platdata->card_inserted) + return !!host->platdata->card_inserted(host->mmc); + + return -ENOSYS; } static int au1xmmc_card_readonly(struct mmc_host *mmc) { struct au1xmmc_host *host = mmc_priv(mmc); - return (bcsr->status & au1xmmc_card_table[host->id].wpstatus) - ? 1 : 0; + + if (host->platdata && host->platdata->card_readonly) + return !!host->platdata->card_readonly(mmc); + + return -ENOSYS; } static void au1xmmc_finish_request(struct au1xmmc_host *host) { - struct mmc_request *mrq = host->mrq; host->mrq = NULL; - host->flags &= HOST_F_ACTIVE; + host->flags &= HOST_F_ACTIVE | HOST_F_DMA; host->dma.len = 0; host->dma.dir = 0; @@ -174,8 +231,6 @@ static void au1xmmc_finish_request(struct au1xmmc_host *host) host->status = HOST_S_IDLE; - bcsr->disk_leds |= (1 << 8); - mmc_request_done(host->mmc, mrq); } @@ -235,18 +290,14 @@ static int au1xmmc_send_command(struct au1xmmc_host *host, int wait, au_sync(); /* Wait for the command to go on the line */ - - while(1) { - if (!(au_readl(HOST_CMD(host)) & SD_CMD_GO)) - break; - } + while (au_readl(HOST_CMD(host)) & SD_CMD_GO) + /* nop */; /* Wait for the command to come back */ - if (wait) { u32 status = au_readl(HOST_STATUS(host)); - while(!(status & SD_STATUS_CR)) + while (!(status & SD_STATUS_CR)) status = au_readl(HOST_STATUS(host)); /* Clear the CR status */ @@ -260,12 +311,11 @@ static int au1xmmc_send_command(struct au1xmmc_host *host, int wait, static void au1xmmc_data_complete(struct au1xmmc_host *host, u32 status) { - struct mmc_request *mrq = host->mrq; struct mmc_data *data; u32 crc; - WARN_ON(host->status != HOST_S_DATA && host->status != HOST_S_STOP); + WARN_ON((host->status != HOST_S_DATA) && (host->status != HOST_S_STOP)); if (host->mrq == NULL) return; @@ -276,15 +326,13 @@ static void au1xmmc_data_complete(struct au1xmmc_host *host, u32 status) status = au_readl(HOST_STATUS(host)); /* The transaction is really over when the SD_STATUS_DB bit is clear */ - - while((host->flags & HOST_F_XMIT) && (status & SD_STATUS_DB)) + while ((host->flags & HOST_F_XMIT) && (status & SD_STATUS_DB)) status = au_readl(HOST_STATUS(host)); data->error = 0; dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len, host->dma.dir); /* Process any errors */ - crc = (status & (SD_STATUS_WC | SD_STATUS_RC)); if (host->flags & HOST_F_XMIT) crc |= ((status & 0x07) == 0x02) ? 0 : 1; @@ -299,16 +347,16 @@ static void au1xmmc_data_complete(struct au1xmmc_host *host, u32 status) if (!data->error) { if (host->flags & HOST_F_DMA) { +#ifdef CONFIG_SOC_AU1200 /* DBDMA */ u32 chan = DMA_CHANNEL(host); - chan_tab_t *c = *((chan_tab_t **) chan); + chan_tab_t *c = *((chan_tab_t **)chan); au1x_dma_chan_t *cp = c->chan_ptr; data->bytes_xfered = cp->ddma_bytecnt; - } - else +#endif + } else data->bytes_xfered = - (data->blocks * data->blksz) - - host->pio.len; + (data->blocks * data->blksz) - host->pio.len; } au1xmmc_finish_request(host); @@ -316,7 +364,7 @@ static void au1xmmc_data_complete(struct au1xmmc_host *host, u32 status) static void au1xmmc_tasklet_data(unsigned long param) { - struct au1xmmc_host *host = (struct au1xmmc_host *) param; + struct au1xmmc_host *host = (struct au1xmmc_host *)param; u32 status = au_readl(HOST_STATUS(host)); au1xmmc_data_complete(host, status); @@ -326,11 +374,10 @@ static void au1xmmc_tasklet_data(unsigned long param) static void au1xmmc_send_pio(struct au1xmmc_host *host) { - - struct mmc_data *data = 0; - int sg_len, max, count = 0; - unsigned char *sg_ptr; - u32 status = 0; + struct mmc_data *data; + int sg_len, max, count; + unsigned char *sg_ptr, val; + u32 status; struct scatterlist *sg; data = host->mrq->data; @@ -345,14 +392,12 @@ static void au1xmmc_send_pio(struct au1xmmc_host *host) /* This is the space left inside the buffer */ sg_len = data->sg[host->pio.index].length - host->pio.offset; - /* Check to if we need less then the size of the sg_buffer */ - + /* Check if we need less than the size of the sg_buffer */ max = (sg_len > host->pio.len) ? host->pio.len : sg_len; - if (max > AU1XMMC_MAX_TRANSFER) max = AU1XMMC_MAX_TRANSFER; - - for(count = 0; count < max; count++ ) { - unsigned char val; + if (max > AU1XMMC_MAX_TRANSFER) + max = AU1XMMC_MAX_TRANSFER; + for (count = 0; count < max; count++) { status = au_readl(HOST_STATUS(host)); if (!(status & SD_STATUS_TH)) @@ -360,7 +405,7 @@ static void au1xmmc_send_pio(struct au1xmmc_host *host) val = *sg_ptr++; - au_writel((unsigned long) val, HOST_TXPORT(host)); + au_writel((unsigned long)val, HOST_TXPORT(host)); au_sync(); } @@ -384,11 +429,10 @@ static void au1xmmc_send_pio(struct au1xmmc_host *host) static void au1xmmc_receive_pio(struct au1xmmc_host *host) { - - struct mmc_data *data = 0; - int sg_len = 0, max = 0, count = 0; - unsigned char *sg_ptr = 0; - u32 status = 0; + struct mmc_data *data; + int max, count, sg_len = 0; + unsigned char *sg_ptr = NULL; + u32 status, val; struct scatterlist *sg; data = host->mrq->data; @@ -405,33 +449,33 @@ static void au1xmmc_receive_pio(struct au1xmmc_host *host) /* This is the space left inside the buffer */ sg_len = sg_dma_len(&data->sg[host->pio.index]) - host->pio.offset; - /* Check to if we need less then the size of the sg_buffer */ - if (sg_len < max) max = sg_len; + /* Check if we need less than the size of the sg_buffer */ + if (sg_len < max) + max = sg_len; } if (max > AU1XMMC_MAX_TRANSFER) max = AU1XMMC_MAX_TRANSFER; - for(count = 0; count < max; count++ ) { - u32 val; + for (count = 0; count < max; count++) { status = au_readl(HOST_STATUS(host)); if (!(status & SD_STATUS_NE)) break; if (status & SD_STATUS_RC) { - DBG("RX CRC Error [%d + %d].\n", host->id, + DBG("RX CRC Error [%d + %d].\n", host->pdev->id, host->pio.len, count); break; } if (status & SD_STATUS_RO) { - DBG("RX Overrun [%d + %d]\n", host->id, + DBG("RX Overrun [%d + %d]\n", host->pdev->id, host->pio.len, count); break; } else if (status & SD_STATUS_RU) { - DBG("RX Underrun [%d + %d]\n", host->id, + DBG("RX Underrun [%d + %d]\n", host->pdev->id, host->pio.len, count); break; } @@ -439,7 +483,7 @@ static void au1xmmc_receive_pio(struct au1xmmc_host *host) val = au_readl(HOST_RXPORT(host)); if (sg_ptr) - *sg_ptr++ = (unsigned char) (val & 0xFF); + *sg_ptr++ = (unsigned char)(val & 0xFF); } host->pio.len -= count; @@ -451,7 +495,7 @@ static void au1xmmc_receive_pio(struct au1xmmc_host *host) } if (host->pio.len == 0) { - //IRQ_OFF(host, SD_CONFIG_RA | SD_CONFIG_RF); + /* IRQ_OFF(host, SD_CONFIG_RA | SD_CONFIG_RF); */ IRQ_OFF(host, SD_CONFIG_NE); if (host->flags & HOST_F_STOP) @@ -461,17 +505,15 @@ static void au1xmmc_receive_pio(struct au1xmmc_host *host) } } -/* static void au1xmmc_cmd_complete - This is called when a command has been completed - grab the response - and check for errors. Then start the data transfer if it is indicated. -*/ - +/* This is called when a command has been completed - grab the response + * and check for errors. Then start the data transfer if it is indicated. + */ static void au1xmmc_cmd_complete(struct au1xmmc_host *host, u32 status) { - struct mmc_request *mrq = host->mrq; struct mmc_command *cmd; - int trans; + u32 r[4]; + int i, trans; if (!host->mrq) return; @@ -481,9 +523,6 @@ static void au1xmmc_cmd_complete(struct au1xmmc_host *host, u32 status) if (cmd->flags & MMC_RSP_PRESENT) { if (cmd->flags & MMC_RSP_136) { - u32 r[4]; - int i; - r[0] = au_readl(host->iobase + SD_RESP3); r[1] = au_readl(host->iobase + SD_RESP2); r[2] = au_readl(host->iobase + SD_RESP1); @@ -491,10 +530,9 @@ static void au1xmmc_cmd_complete(struct au1xmmc_host *host, u32 status) /* The CRC is omitted from the response, so really * we only got 120 bytes, but the engine expects - * 128 bits, so we have to shift things up + * 128 bits, so we have to shift things up. */ - - for(i = 0; i < 4; i++) { + for (i = 0; i < 4; i++) { cmd->resp[i] = (r[i] & 0x00FFFFFF) << 8; if (i != 3) cmd->resp[i] |= (r[i + 1] & 0xFF000000) >> 24; @@ -505,22 +543,20 @@ static void au1xmmc_cmd_complete(struct au1xmmc_host *host, u32 status) * our response omits the CRC, our data ends up * being shifted 8 bits to the right. In this case, * that means that the OSR data starts at bit 31, - * so we can just read RESP0 and return that + * so we can just read RESP0 and return that. */ cmd->resp[0] = au_readl(host->iobase + SD_RESP0); } } /* Figure out errors */ - if (status & (SD_STATUS_SC | SD_STATUS_WC | SD_STATUS_RC)) cmd->error = -EILSEQ; trans = host->flags & (HOST_F_XMIT | HOST_F_RECV); if (!trans || cmd->error) { - - IRQ_OFF(host, SD_CONFIG_TH | SD_CONFIG_RA|SD_CONFIG_RF); + IRQ_OFF(host, SD_CONFIG_TH | SD_CONFIG_RA | SD_CONFIG_RF); tasklet_schedule(&host->finish_task); return; } @@ -528,6 +564,7 @@ static void au1xmmc_cmd_complete(struct au1xmmc_host *host, u32 status) host->status = HOST_S_DATA; if (host->flags & HOST_F_DMA) { +#ifdef CONFIG_SOC_AU1200 /* DBDMA */ u32 channel = DMA_CHANNEL(host); /* Start the DMA as soon as the buffer gets something in it */ @@ -540,23 +577,21 @@ static void au1xmmc_cmd_complete(struct au1xmmc_host *host, u32 status) } au1xxx_dbdma_start(channel); +#endif } } static void au1xmmc_set_clock(struct au1xmmc_host *host, int rate) { - unsigned int pbus = get_au1x00_speed(); unsigned int divisor; u32 config; /* From databook: - divisor = ((((cpuclock / sbus_divisor) / 2) / mmcclock) / 2) - 1 - */ - + * divisor = ((((cpuclock / sbus_divisor) / 2) / mmcclock) / 2) - 1 + */ pbus /= ((au_readl(SYS_POWERCTRL) & 0x3) + 2); pbus /= 2; - divisor = ((pbus / rate) / 2) - 1; config = au_readl(HOST_CONFIG(host)); @@ -568,15 +603,11 @@ static void au1xmmc_set_clock(struct au1xmmc_host *host, int rate) au_sync(); } -static int -au1xmmc_prepare_data(struct au1xmmc_host *host, struct mmc_data *data) +static int au1xmmc_prepare_data(struct au1xmmc_host *host, + struct mmc_data *data) { - int datalen = data->blocks * data->blksz; - if (dma != 0) - host->flags |= HOST_F_DMA; - if (data->flags & MMC_DATA_READ) host->flags |= HOST_F_RECV; else @@ -596,12 +627,13 @@ au1xmmc_prepare_data(struct au1xmmc_host *host, struct mmc_data *data) au_writel(data->blksz - 1, HOST_BLKSIZE(host)); if (host->flags & HOST_F_DMA) { +#ifdef CONFIG_SOC_AU1200 /* DBDMA */ int i; u32 channel = DMA_CHANNEL(host); au1xxx_dbdma_stop(channel); - for(i = 0; i < host->dma.len; i++) { + for (i = 0; i < host->dma.len; i++) { u32 ret = 0, flags = DDMA_FLAGS_NOIE; struct scatterlist *sg = &data->sg[i]; int sg_len = sg->length; @@ -611,23 +643,21 @@ au1xmmc_prepare_data(struct au1xmmc_host *host, struct mmc_data *data) if (i == host->dma.len - 1) flags = DDMA_FLAGS_IE; - if (host->flags & HOST_F_XMIT){ - ret = au1xxx_dbdma_put_source_flags(channel, - (void *) sg_virt(sg), len, flags); - } - else { - ret = au1xxx_dbdma_put_dest_flags(channel, - (void *) sg_virt(sg), - len, flags); + if (host->flags & HOST_F_XMIT) { + ret = au1xxx_dbdma_put_source_flags(channel, + (void *)sg_virt(sg), len, flags); + } else { + ret = au1xxx_dbdma_put_dest_flags(channel, + (void *)sg_virt(sg), len, flags); } - if (!ret) + if (!ret) goto dataerr; datalen -= len; } - } - else { +#endif + } else { host->pio.index = 0; host->pio.offset = 0; host->pio.len = datalen; @@ -636,25 +666,21 @@ au1xmmc_prepare_data(struct au1xmmc_host *host, struct mmc_data *data) IRQ_ON(host, SD_CONFIG_TH); else IRQ_ON(host, SD_CONFIG_NE); - //IRQ_ON(host, SD_CONFIG_RA|SD_CONFIG_RF); + /* IRQ_ON(host, SD_CONFIG_RA | SD_CONFIG_RF); */ } return 0; - dataerr: - dma_unmap_sg(mmc_dev(host->mmc),data->sg,data->sg_len,host->dma.dir); +dataerr: + dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len, + host->dma.dir); return -ETIMEDOUT; } -/* static void au1xmmc_request - This actually starts a command or data transaction -*/ - +/* This actually starts a command or data transaction */ static void au1xmmc_request(struct mmc_host* mmc, struct mmc_request* mrq) { - struct au1xmmc_host *host = mmc_priv(mmc); - unsigned int flags = 0; int ret = 0; WARN_ON(irqs_disabled()); @@ -663,11 +689,15 @@ static void au1xmmc_request(struct mmc_host* mmc, struct mmc_request* mrq) host->mrq = mrq; host->status = HOST_S_CMD; - bcsr->disk_leds &= ~(1 << 8); + /* fail request immediately if no card is present */ + if (0 == au1xmmc_card_inserted(mmc)) { + mrq->cmd->error = -ENOMEDIUM; + au1xmmc_finish_request(host); + return; + } if (mrq->data) { FLUSH_FIFO(host); - flags = mrq->data->flags; ret = au1xmmc_prepare_data(host, mrq->data); } @@ -682,7 +712,6 @@ static void au1xmmc_request(struct mmc_host* mmc, struct mmc_request* mrq) static void au1xmmc_reset_controller(struct au1xmmc_host *host) { - /* Apply the clock */ au_writel(SD_ENABLE_CE, HOST_ENABLE(host)); au_sync_delay(1); @@ -712,9 +741,10 @@ static void au1xmmc_reset_controller(struct au1xmmc_host *host) } -static void au1xmmc_set_ios(struct mmc_host* mmc, struct mmc_ios* ios) +static void au1xmmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) { struct au1xmmc_host *host = mmc_priv(mmc); + u32 config2; if (ios->power_mode == MMC_POWER_OFF) au1xmmc_set_power(host, 0); @@ -726,21 +756,18 @@ static void au1xmmc_set_ios(struct mmc_host* mmc, struct mmc_ios* ios) au1xmmc_set_clock(host, ios->clock); host->clock = ios->clock; } -} - -static void au1xmmc_dma_callback(int irq, void *dev_id) -{ - struct au1xmmc_host *host = (struct au1xmmc_host *) dev_id; - - /* Avoid spurious interrupts */ - if (!host->mrq) - return; - - if (host->flags & HOST_F_STOP) - SEND_STOP(host); - - tasklet_schedule(&host->data_task); + config2 = au_readl(HOST_CONFIG2(host)); + switch (ios->bus_width) { + case MMC_BUS_WIDTH_4: + config2 |= SD_CONFIG2_WB; + break; + case MMC_BUS_WIDTH_1: + config2 &= ~SD_CONFIG2_WB; + break; + } + au_writel(config2, HOST_CONFIG2(host)); + au_sync(); } #define STATUS_TIMEOUT (SD_STATUS_RAT | SD_STATUS_DT) @@ -749,245 +776,354 @@ static void au1xmmc_dma_callback(int irq, void *dev_id) static irqreturn_t au1xmmc_irq(int irq, void *dev_id) { - + struct au1xmmc_host *host = dev_id; u32 status; - int i, ret = 0; - - disable_irq(AU1100_SD_IRQ); - for(i = 0; i < AU1XMMC_CONTROLLER_COUNT; i++) { - struct au1xmmc_host * host = au1xmmc_hosts[i]; - u32 handled = 1; + status = au_readl(HOST_STATUS(host)); - status = au_readl(HOST_STATUS(host)); + if (!(status & SD_STATUS_I)) + return IRQ_NONE; /* not ours */ - if (host->mrq && (status & STATUS_TIMEOUT)) { - if (status & SD_STATUS_RAT) - host->mrq->cmd->error = -ETIMEDOUT; + if (status & SD_STATUS_SI) /* SDIO */ + mmc_signal_sdio_irq(host->mmc); - else if (status & SD_STATUS_DT) - host->mrq->data->error = -ETIMEDOUT; + if (host->mrq && (status & STATUS_TIMEOUT)) { + if (status & SD_STATUS_RAT) + host->mrq->cmd->error = -ETIMEDOUT; + else if (status & SD_STATUS_DT) + host->mrq->data->error = -ETIMEDOUT; - /* In PIO mode, interrupts might still be enabled */ - IRQ_OFF(host, SD_CONFIG_NE | SD_CONFIG_TH); + /* In PIO mode, interrupts might still be enabled */ + IRQ_OFF(host, SD_CONFIG_NE | SD_CONFIG_TH); - //IRQ_OFF(host, SD_CONFIG_TH|SD_CONFIG_RA|SD_CONFIG_RF); - tasklet_schedule(&host->finish_task); - } + /* IRQ_OFF(host, SD_CONFIG_TH | SD_CONFIG_RA | SD_CONFIG_RF); */ + tasklet_schedule(&host->finish_task); + } #if 0 - else if (status & SD_STATUS_DD) { - - /* Sometimes we get a DD before a NE in PIO mode */ - - if (!(host->flags & HOST_F_DMA) && - (status & SD_STATUS_NE)) - au1xmmc_receive_pio(host); - else { - au1xmmc_data_complete(host, status); - //tasklet_schedule(&host->data_task); - } + else if (status & SD_STATUS_DD) { + /* Sometimes we get a DD before a NE in PIO mode */ + if (!(host->flags & HOST_F_DMA) && (status & SD_STATUS_NE)) + au1xmmc_receive_pio(host); + else { + au1xmmc_data_complete(host, status); + /* tasklet_schedule(&host->data_task); */ } + } #endif - else if (status & (SD_STATUS_CR)) { - if (host->status == HOST_S_CMD) - au1xmmc_cmd_complete(host,status); - } - else if (!(host->flags & HOST_F_DMA)) { - if ((host->flags & HOST_F_XMIT) && - (status & STATUS_DATA_OUT)) - au1xmmc_send_pio(host); - else if ((host->flags & HOST_F_RECV) && - (status & STATUS_DATA_IN)) - au1xmmc_receive_pio(host); - } - else if (status & 0x203FBC70) { - DBG("Unhandled status %8.8x\n", host->id, status); - handled = 0; - } - - au_writel(status, HOST_STATUS(host)); - au_sync(); - - ret |= handled; + else if (status & SD_STATUS_CR) { + if (host->status == HOST_S_CMD) + au1xmmc_cmd_complete(host, status); + + } else if (!(host->flags & HOST_F_DMA)) { + if ((host->flags & HOST_F_XMIT) && (status & STATUS_DATA_OUT)) + au1xmmc_send_pio(host); + else if ((host->flags & HOST_F_RECV) && (status & STATUS_DATA_IN)) + au1xmmc_receive_pio(host); + + } else if (status & 0x203F3C70) { + DBG("Unhandled status %8.8x\n", host->pdev->id, + status); } - enable_irq(AU1100_SD_IRQ); - return ret; + au_writel(status, HOST_STATUS(host)); + au_sync(); + + return IRQ_HANDLED; } -static void au1xmmc_poll_event(unsigned long arg) -{ - struct au1xmmc_host *host = (struct au1xmmc_host *) arg; +#ifdef CONFIG_SOC_AU1200 +/* 8bit memory DMA device */ +static dbdev_tab_t au1xmmc_mem_dbdev = { + .dev_id = DSCR_CMD0_ALWAYS, + .dev_flags = DEV_FLAGS_ANYUSE, + .dev_tsize = 0, + .dev_devwidth = 8, + .dev_physaddr = 0x00000000, + .dev_intlevel = 0, + .dev_intpolarity = 0, +}; +static int memid; - int card = au1xmmc_card_inserted(host); - int controller = (host->flags & HOST_F_ACTIVE) ? 1 : 0; +static void au1xmmc_dbdma_callback(int irq, void *dev_id) +{ + struct au1xmmc_host *host = (struct au1xmmc_host *)dev_id; - if (card != controller) { - host->flags &= ~HOST_F_ACTIVE; - if (card) host->flags |= HOST_F_ACTIVE; - mmc_detect_change(host->mmc, 0); - } + /* Avoid spurious interrupts */ + if (!host->mrq) + return; - if (host->mrq != NULL) { - u32 status = au_readl(HOST_STATUS(host)); - DBG("PENDING - %8.8x\n", host->id, status); - } + if (host->flags & HOST_F_STOP) + SEND_STOP(host); - mod_timer(&host->timer, jiffies + AU1XMMC_DETECT_TIMEOUT); + tasklet_schedule(&host->data_task); } -static dbdev_tab_t au1xmmc_mem_dbdev = -{ - DSCR_CMD0_ALWAYS, DEV_FLAGS_ANYUSE, 0, 8, 0x00000000, 0, 0 -}; - -static void au1xmmc_init_dma(struct au1xmmc_host *host) +static int au1xmmc_dbdma_init(struct au1xmmc_host *host) { + struct resource *res; + int txid, rxid; + + res = platform_get_resource(host->pdev, IORESOURCE_DMA, 0); + if (!res) + return -ENODEV; + txid = res->start; + + res = platform_get_resource(host->pdev, IORESOURCE_DMA, 1); + if (!res) + return -ENODEV; + rxid = res->start; + + if (!memid) + return -ENODEV; + + host->tx_chan = au1xxx_dbdma_chan_alloc(memid, txid, + au1xmmc_dbdma_callback, (void *)host); + if (!host->tx_chan) { + dev_err(&host->pdev->dev, "cannot allocate TX DMA\n"); + return -ENODEV; + } - u32 rxchan, txchan; - - int txid = au1xmmc_card_table[host->id].tx_devid; - int rxid = au1xmmc_card_table[host->id].rx_devid; + host->rx_chan = au1xxx_dbdma_chan_alloc(rxid, memid, + au1xmmc_dbdma_callback, (void *)host); + if (!host->rx_chan) { + dev_err(&host->pdev->dev, "cannot allocate RX DMA\n"); + au1xxx_dbdma_chan_free(host->tx_chan); + return -ENODEV; + } - /* DSCR_CMD0_ALWAYS has a stride of 32 bits, we need a stride - of 8 bits. And since devices are shared, we need to create - our own to avoid freaking out other devices - */ + au1xxx_dbdma_set_devwidth(host->tx_chan, 8); + au1xxx_dbdma_set_devwidth(host->rx_chan, 8); - int memid = au1xxx_ddma_add_device(&au1xmmc_mem_dbdev); + au1xxx_dbdma_ring_alloc(host->tx_chan, AU1XMMC_DESCRIPTOR_COUNT); + au1xxx_dbdma_ring_alloc(host->rx_chan, AU1XMMC_DESCRIPTOR_COUNT); - txchan = au1xxx_dbdma_chan_alloc(memid, txid, - au1xmmc_dma_callback, (void *) host); + /* DBDMA is good to go */ + host->flags |= HOST_F_DMA; - rxchan = au1xxx_dbdma_chan_alloc(rxid, memid, - au1xmmc_dma_callback, (void *) host); + return 0; +} - au1xxx_dbdma_set_devwidth(txchan, 8); - au1xxx_dbdma_set_devwidth(rxchan, 8); +static void au1xmmc_dbdma_shutdown(struct au1xmmc_host *host) +{ + if (host->flags & HOST_F_DMA) { + host->flags &= ~HOST_F_DMA; + au1xxx_dbdma_chan_free(host->tx_chan); + au1xxx_dbdma_chan_free(host->rx_chan); + } +} +#endif - au1xxx_dbdma_ring_alloc(txchan, AU1XMMC_DESCRIPTOR_COUNT); - au1xxx_dbdma_ring_alloc(rxchan, AU1XMMC_DESCRIPTOR_COUNT); +static void au1xmmc_enable_sdio_irq(struct mmc_host *mmc, int en) +{ + struct au1xmmc_host *host = mmc_priv(mmc); - host->tx_chan = txchan; - host->rx_chan = rxchan; + if (en) + IRQ_ON(host, SD_CONFIG_SI); + else + IRQ_OFF(host, SD_CONFIG_SI); } static const struct mmc_host_ops au1xmmc_ops = { .request = au1xmmc_request, .set_ios = au1xmmc_set_ios, .get_ro = au1xmmc_card_readonly, + .get_cd = au1xmmc_card_inserted, + .enable_sdio_irq = au1xmmc_enable_sdio_irq, }; static int __devinit au1xmmc_probe(struct platform_device *pdev) { + struct mmc_host *mmc; + struct au1xmmc_host *host; + struct resource *r; + int ret; + + mmc = mmc_alloc_host(sizeof(struct au1xmmc_host), &pdev->dev); + if (!mmc) { + dev_err(&pdev->dev, "no memory for mmc_host\n"); + ret = -ENOMEM; + goto out0; + } - int i, ret = 0; - - /* THe interrupt is shared among all controllers */ - ret = request_irq(AU1100_SD_IRQ, au1xmmc_irq, IRQF_DISABLED, "MMC", 0); + host = mmc_priv(mmc); + host->mmc = mmc; + host->platdata = pdev->dev.platform_data; + host->pdev = pdev; - if (ret) { - printk(DRIVER_NAME "ERROR: Couldn't get int %d: %d\n", - AU1100_SD_IRQ, ret); - return -ENXIO; + ret = -ENODEV; + r = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!r) { + dev_err(&pdev->dev, "no mmio defined\n"); + goto out1; } - disable_irq(AU1100_SD_IRQ); + host->ioarea = request_mem_region(r->start, r->end - r->start + 1, + pdev->name); + if (!host->ioarea) { + dev_err(&pdev->dev, "mmio already in use\n"); + goto out1; + } - for(i = 0; i < AU1XMMC_CONTROLLER_COUNT; i++) { - struct mmc_host *mmc = mmc_alloc_host(sizeof(struct au1xmmc_host), &pdev->dev); - struct au1xmmc_host *host = 0; + host->iobase = (unsigned long)ioremap(r->start, 0x3c); + if (!host->iobase) { + dev_err(&pdev->dev, "cannot remap mmio\n"); + goto out2; + } - if (!mmc) { - printk(DRIVER_NAME "ERROR: no mem for host %d\n", i); - au1xmmc_hosts[i] = 0; - continue; - } + r = platform_get_resource(pdev, IORESOURCE_IRQ, 0); + if (!r) { + dev_err(&pdev->dev, "no IRQ defined\n"); + goto out3; + } - mmc->ops = &au1xmmc_ops; + host->irq = r->start; + /* IRQ is shared among both SD controllers */ + ret = request_irq(host->irq, au1xmmc_irq, IRQF_SHARED, + DRIVER_NAME, host); + if (ret) { + dev_err(&pdev->dev, "cannot grab IRQ\n"); + goto out3; + } - mmc->f_min = 450000; - mmc->f_max = 24000000; + mmc->ops = &au1xmmc_ops; - mmc->max_seg_size = AU1XMMC_DESCRIPTOR_SIZE; - mmc->max_phys_segs = AU1XMMC_DESCRIPTOR_COUNT; + mmc->f_min = 450000; + mmc->f_max = 24000000; - mmc->max_blk_size = 2048; - mmc->max_blk_count = 512; + mmc->max_seg_size = AU1XMMC_DESCRIPTOR_SIZE; + mmc->max_phys_segs = AU1XMMC_DESCRIPTOR_COUNT; - mmc->ocr_avail = AU1XMMC_OCR; + mmc->max_blk_size = 2048; + mmc->max_blk_count = 512; - host = mmc_priv(mmc); - host->mmc = mmc; + mmc->ocr_avail = AU1XMMC_OCR; + mmc->caps = MMC_CAP_4_BIT_DATA | MMC_CAP_SDIO_IRQ; - host->id = i; - host->iobase = au1xmmc_card_table[host->id].iobase; - host->clock = 0; - host->power_mode = MMC_POWER_OFF; + host->status = HOST_S_IDLE; - host->flags = au1xmmc_card_inserted(host) ? HOST_F_ACTIVE : 0; - host->status = HOST_S_IDLE; + /* board-specific carddetect setup, if any */ + if (host->platdata && host->platdata->cd_setup) { + ret = host->platdata->cd_setup(mmc, 1); + if (ret) { + dev_warn(&pdev->dev, "board CD setup failed\n"); + mmc->caps |= MMC_CAP_NEEDS_POLL; + } + } else + mmc->caps |= MMC_CAP_NEEDS_POLL; - init_timer(&host->timer); + tasklet_init(&host->data_task, au1xmmc_tasklet_data, + (unsigned long)host); - host->timer.function = au1xmmc_poll_event; - host->timer.data = (unsigned long) host; - host->timer.expires = jiffies + AU1XMMC_DETECT_TIMEOUT; + tasklet_init(&host->finish_task, au1xmmc_tasklet_finish, + (unsigned long)host); - tasklet_init(&host->data_task, au1xmmc_tasklet_data, - (unsigned long) host); +#ifdef CONFIG_SOC_AU1200 + ret = au1xmmc_dbdma_init(host); + if (ret) + printk(KERN_INFO DRIVER_NAME ": DBDMA init failed; using PIO\n"); +#endif - tasklet_init(&host->finish_task, au1xmmc_tasklet_finish, - (unsigned long) host); +#ifdef CONFIG_LEDS_CLASS + if (host->platdata && host->platdata->led) { + struct led_classdev *led = host->platdata->led; + led->name = mmc_hostname(mmc); + led->brightness = LED_OFF; + led->default_trigger = mmc_hostname(mmc); + ret = led_classdev_register(mmc_dev(mmc), led); + if (ret) + goto out5; + } +#endif - spin_lock_init(&host->lock); + au1xmmc_reset_controller(host); - if (dma != 0) - au1xmmc_init_dma(host); + ret = mmc_add_host(mmc); + if (ret) { + dev_err(&pdev->dev, "cannot add mmc host\n"); + goto out6; + } - au1xmmc_reset_controller(host); + platform_set_drvdata(pdev, mmc); - mmc_add_host(mmc); - au1xmmc_hosts[i] = host; + printk(KERN_INFO DRIVER_NAME ": MMC Controller %d set up at %8.8X" + " (mode=%s)\n", pdev->id, host->iobase, + host->flags & HOST_F_DMA ? "dma" : "pio"); - add_timer(&host->timer); + return 0; /* all ok */ - printk(KERN_INFO DRIVER_NAME ": MMC Controller %d set up at %8.8X (mode=%s)\n", - host->id, host->iobase, dma ? "dma" : "pio"); - } +out6: +#ifdef CONFIG_LEDS_CLASS + if (host->platdata && host->platdata->led) + led_classdev_unregister(host->platdata->led); +out5: +#endif + au_writel(0, HOST_ENABLE(host)); + au_writel(0, HOST_CONFIG(host)); + au_writel(0, HOST_CONFIG2(host)); + au_sync(); - enable_irq(AU1100_SD_IRQ); +#ifdef CONFIG_SOC_AU1200 + au1xmmc_dbdma_shutdown(host); +#endif - return 0; + tasklet_kill(&host->data_task); + tasklet_kill(&host->finish_task); + + if (host->platdata && host->platdata->cd_setup && + !(mmc->caps & MMC_CAP_NEEDS_POLL)) + host->platdata->cd_setup(mmc, 0); + + free_irq(host->irq, host); +out3: + iounmap((void *)host->iobase); +out2: + release_resource(host->ioarea); + kfree(host->ioarea); +out1: + mmc_free_host(mmc); +out0: + return ret; } static int __devexit au1xmmc_remove(struct platform_device *pdev) { + struct mmc_host *mmc = platform_get_drvdata(pdev); + struct au1xmmc_host *host; + + if (mmc) { + host = mmc_priv(mmc); - int i; + mmc_remove_host(mmc); - disable_irq(AU1100_SD_IRQ); +#ifdef CONFIG_LEDS_CLASS + if (host->platdata && host->platdata->led) + led_classdev_unregister(host->platdata->led); +#endif - for(i = 0; i < AU1XMMC_CONTROLLER_COUNT; i++) { - struct au1xmmc_host *host = au1xmmc_hosts[i]; - if (!host) continue; + if (host->platdata && host->platdata->cd_setup && + !(mmc->caps & MMC_CAP_NEEDS_POLL)) + host->platdata->cd_setup(mmc, 0); + + au_writel(0, HOST_ENABLE(host)); + au_writel(0, HOST_CONFIG(host)); + au_writel(0, HOST_CONFIG2(host)); + au_sync(); tasklet_kill(&host->data_task); tasklet_kill(&host->finish_task); - del_timer_sync(&host->timer); +#ifdef CONFIG_SOC_AU1200 + au1xmmc_dbdma_shutdown(host); +#endif au1xmmc_set_power(host, 0); - mmc_remove_host(host->mmc); - - au1xxx_dbdma_chan_free(host->tx_chan); - au1xxx_dbdma_chan_free(host->rx_chan); + free_irq(host->irq, host); + iounmap((void *)host->iobase); + release_resource(host->ioarea); + kfree(host->ioarea); - au_writel(0x0, HOST_ENABLE(host)); - au_sync(); + mmc_free_host(mmc); } - - free_irq(AU1100_SD_IRQ, 0); return 0; } @@ -1004,21 +1140,31 @@ static struct platform_driver au1xmmc_driver = { static int __init au1xmmc_init(void) { +#ifdef CONFIG_SOC_AU1200 + /* DSCR_CMD0_ALWAYS has a stride of 32 bits, we need a stride + * of 8 bits. And since devices are shared, we need to create + * our own to avoid freaking out other devices. + */ + memid = au1xxx_ddma_add_device(&au1xmmc_mem_dbdev); + if (!memid) + printk(KERN_ERR "au1xmmc: cannot add memory dbdma dev\n"); +#endif return platform_driver_register(&au1xmmc_driver); } static void __exit au1xmmc_exit(void) { +#ifdef CONFIG_SOC_AU1200 + if (memid) + au1xxx_ddma_del_device(memid); +#endif platform_driver_unregister(&au1xmmc_driver); } module_init(au1xmmc_init); module_exit(au1xmmc_exit); -#ifdef MODULE MODULE_AUTHOR("Advanced Micro Devices, Inc"); MODULE_DESCRIPTION("MMC/SD driver for the Alchemy Au1XXX"); MODULE_LICENSE("GPL"); MODULE_ALIAS("platform:au1xxx-mmc"); -#endif - |