diff options
Diffstat (limited to 'drivers/mmc/host')
| -rw-r--r-- | drivers/mmc/host/Kconfig | 6 | ||||
| -rw-r--r-- | drivers/mmc/host/Makefile | 1 | ||||
| -rw-r--r-- | drivers/mmc/host/tmio_mmc.c | 691 | ||||
| -rw-r--r-- | drivers/mmc/host/tmio_mmc.h | 194 |
4 files changed, 892 insertions, 0 deletions
diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig index dc6f2579f85..6fef078a204 100644 --- a/drivers/mmc/host/Kconfig +++ b/drivers/mmc/host/Kconfig @@ -174,3 +174,9 @@ config MMC_SDRICOH_CS To compile this driver as a module, choose M here: the module will be called sdricoh_cs. +config MMC_TMIO + tristate "Toshiba Mobile IO Controller (TMIO) MMC/SD function support" + depends on MFD_CORE + help + This provides support for the SD/MMC cell found in TC6393XB, + T7L66XB and also ipaq ASIC3 diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile index db52eebfb50..c794cc5ce44 100644 --- a/drivers/mmc/host/Makefile +++ b/drivers/mmc/host/Makefile @@ -21,4 +21,5 @@ obj-$(CONFIG_MMC_TIFM_SD) += tifm_sd.o obj-$(CONFIG_MMC_SPI) += mmc_spi.o obj-$(CONFIG_MMC_S3C) += s3cmci.o obj-$(CONFIG_MMC_SDRICOH_CS) += sdricoh_cs.o +obj-$(CONFIG_MMC_TMIO) += tmio_mmc.o diff --git a/drivers/mmc/host/tmio_mmc.c b/drivers/mmc/host/tmio_mmc.c new file mode 100644 index 00000000000..95430b81ec1 --- /dev/null +++ b/drivers/mmc/host/tmio_mmc.c @@ -0,0 +1,691 @@ +/* + * linux/drivers/mmc/tmio_mmc.c + * + * Copyright (C) 2004 Ian Molton + * Copyright (C) 2007 Ian Molton + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * Driver for the MMC / SD / SDIO cell found in: + * + * TC6393XB TC6391XB TC6387XB T7L66XB + * + * This driver draws mainly on scattered spec sheets, Reverse engineering + * of the toshiba e800 SD driver and some parts of the 2.4 ASIC3 driver (4 bit + * support). (Further 4 bit support from a later datasheet). + * + * TODO: + * Investigate using a workqueue for PIO transfers + * Eliminate FIXMEs + * SDIO support + * Better Power management + * Handle MMC errors better + * double buffer support + * + */ +#include <linux/module.h> +#include <linux/irq.h> +#include <linux/device.h> +#include <linux/delay.h> +#include <linux/mmc/host.h> +#include <linux/mfd/core.h> +#include <linux/mfd/tmio.h> + +#include "tmio_mmc.h" + +/* + * Fixme - documentation conflicts on what the clock values are for the + * various dividers. + * One document I have says that its a divisor of a 24MHz clock, another 33. + * This probably depends on HCLK for a given platform, so we may need to + * require HCLK be passed to us from the MFD core. + * + */ + +static void tmio_mmc_set_clock(struct tmio_mmc_host *host, int new_clock) +{ + void __iomem *cnf = host->cnf; + void __iomem *ctl = host->ctl; + u32 clk = 0, clock; + + if (new_clock) { + for (clock = 46875, clk = 0x100; new_clock >= (clock<<1); ) { + clock <<= 1; + clk >>= 1; + } + if (clk & 0x1) + clk = 0x20000; + + clk >>= 2; + tmio_iowrite8((clk & 0x8000) ? 0 : 1, cnf + CNF_SD_CLK_MODE); + clk |= 0x100; + } + + tmio_iowrite16(clk, ctl + CTL_SD_CARD_CLK_CTL); +} + +static void tmio_mmc_clk_stop(struct tmio_mmc_host *host) +{ + void __iomem *ctl = host->ctl; + + tmio_iowrite16(0x0000, ctl + CTL_CLK_AND_WAIT_CTL); + msleep(10); + tmio_iowrite16(tmio_ioread16(ctl + CTL_SD_CARD_CLK_CTL) & ~0x0100, + ctl + CTL_SD_CARD_CLK_CTL); + msleep(10); +} + +static void tmio_mmc_clk_start(struct tmio_mmc_host *host) +{ + void __iomem *ctl = host->ctl; + + tmio_iowrite16(tmio_ioread16(ctl + CTL_SD_CARD_CLK_CTL) | 0x0100, + ctl + CTL_SD_CARD_CLK_CTL); + msleep(10); + tmio_iowrite16(0x0100, ctl + CTL_CLK_AND_WAIT_CTL); + msleep(10); +} + +static void reset(struct tmio_mmc_host *host) +{ + void __iomem *ctl = host->ctl; + + /* FIXME - should we set stop clock reg here */ + tmio_iowrite16(0x0000, ctl + CTL_RESET_SD); + tmio_iowrite16(0x0000, ctl + CTL_RESET_SDIO); + msleep(10); + tmio_iowrite16(0x0001, ctl + CTL_RESET_SD); + tmio_iowrite16(0x0001, ctl + CTL_RESET_SDIO); + msleep(10); +} + +static void +tmio_mmc_finish_request(struct tmio_mmc_host *host) +{ + struct mmc_request *mrq = host->mrq; + + host->mrq = NULL; + host->cmd = NULL; + host->data = NULL; + + mmc_request_done(host->mmc, mrq); +} + +/* These are the bitmasks the tmio chip requires to implement the MMC response + * types. Note that R1 and R6 are the same in this scheme. */ +#define APP_CMD 0x0040 +#define RESP_NONE 0x0300 +#define RESP_R1 0x0400 +#define RESP_R1B 0x0500 +#define RESP_R2 0x0600 +#define RESP_R3 0x0700 +#define DATA_PRESENT 0x0800 +#define TRANSFER_READ 0x1000 +#define TRANSFER_MULTI 0x2000 +#define SECURITY_CMD 0x4000 + +static int +tmio_mmc_start_command(struct tmio_mmc_host *host, struct mmc_command *cmd) +{ + void __iomem *ctl = host->ctl; + struct mmc_data *data = host->data; + int c = cmd->opcode; + + /* Command 12 is handled by hardware */ + if (cmd->opcode == 12 && !cmd->arg) { + tmio_iowrite16(0x001, ctl + CTL_STOP_INTERNAL_ACTION); + return 0; + } + + switch (mmc_resp_type(cmd)) { + case MMC_RSP_NONE: c |= RESP_NONE; break; + case MMC_RSP_R1: c |= RESP_R1; break; + case MMC_RSP_R1B: c |= RESP_R1B; break; + case MMC_RSP_R2: c |= RESP_R2; break; + case MMC_RSP_R3: c |= RESP_R3; break; + default: + pr_debug("Unknown response type %d\n", mmc_resp_type(cmd)); + return -EINVAL; + } + + host->cmd = cmd; + +/* FIXME - this seems to be ok comented out but the spec suggest this bit should + * be set when issuing app commands. + * if(cmd->flags & MMC_FLAG_ACMD) + * c |= APP_CMD; + */ + if (data) { + c |= DATA_PRESENT; + if (data->blocks > 1) { + tmio_iowrite16(0x100, ctl + CTL_STOP_INTERNAL_ACTION); + c |= TRANSFER_MULTI; + } + if (data->flags & MMC_DATA_READ) + c |= TRANSFER_READ; + } + + enable_mmc_irqs(ctl, TMIO_MASK_CMD); + + /* Fire off the command */ + tmio_iowrite32(cmd->arg, ctl + CTL_ARG_REG); + tmio_iowrite16(c, ctl + CTL_SD_CMD); + + return 0; +} + +/* This chip always returns (at least?) as much data as you ask for. + * I'm unsure what happens if you ask for less than a block. This should be + * looked into to ensure that a funny length read doesnt hose the controller. + * + */ +static inline void tmio_mmc_pio_irq(struct tmio_mmc_host *host) +{ + void __iomem *ctl = host->ctl; + struct mmc_data *data = host->data; + unsigned short *buf; + unsigned int count; + unsigned long flags; + + if (!data) { + pr_debug("Spurious PIO IRQ\n"); + return; + } + + buf = (unsigned short *)(tmio_mmc_kmap_atomic(host, &flags) + + host->sg_off); + + count = host->sg_ptr->length - host->sg_off; + if (count > data->blksz) + count = data->blksz; + + pr_debug("count: %08x offset: %08x flags %08x\n", + count, host->sg_off, data->flags); + + /* Transfer the data */ + if (data->flags & MMC_DATA_READ) + tmio_ioread16_rep(ctl + CTL_SD_DATA_PORT, buf, count >> 1); + else + tmio_iowrite16_rep(ctl + CTL_SD_DATA_PORT, buf, count >> 1); + + host->sg_off += count; + + tmio_mmc_kunmap_atomic(host, &flags); + + if (host->sg_off == host->sg_ptr->length) + tmio_mmc_next_sg(host); + + return; +} + +static inline void tmio_mmc_data_irq(struct tmio_mmc_host *host) +{ + void __iomem *ctl = host->ctl; + struct mmc_data *data = host->data; + struct mmc_command *stop = data->stop; + + host->data = NULL; + + if (!data) { + pr_debug("Spurious data end IRQ\n"); + return; + } + + /* FIXME - return correct transfer count on errors */ + if (!data->error) + data->bytes_xfered = data->blocks * data->blksz; + else + data->bytes_xfered = 0; + + pr_debug("Completed data request\n"); + + /*FIXME - other drivers allow an optional stop command of any given type + * which we dont do, as the chip can auto generate them. + * Perhaps we can be smarter about when to use auto CMD12 and + * only issue the auto request when we know this is the desired + * stop command, allowing fallback to the stop command the + * upper layers expect. For now, we do what works. + */ + + if (data->flags & MMC_DATA_READ) + disable_mmc_irqs(ctl, TMIO_MASK_READOP); + else + disable_mmc_irqs(ctl, TMIO_MASK_WRITEOP); + + if (stop) { + if (stop->opcode == 12 && !stop->arg) + tmio_iowrite16(0x000, ctl + CTL_STOP_INTERNAL_ACTION); + else + BUG(); + } + + tmio_mmc_finish_request(host); +} + +static inline void tmio_mmc_cmd_irq(struct tmio_mmc_host *host, + unsigned int stat) +{ + void __iomem *ctl = host->ctl, *addr; + struct mmc_command *cmd = host->cmd; + int i; + + if (!host->cmd) { + pr_debug("Spurious CMD irq\n"); + return; + } + + host->cmd = NULL; + + /* This controller is sicker than the PXA one. Not only do we need to + * drop the top 8 bits of the first response word, we also need to + * modify the order of the response for short response command types. + */ + + for (i = 3, addr = ctl + CTL_RESPONSE ; i >= 0 ; i--, addr += 4) + cmd->resp[i] = tmio_ioread32(addr); + + if (cmd->flags & MMC_RSP_136) { + cmd->resp[0] = (cmd->resp[0] << 8) | (cmd->resp[1] >> 24); + cmd->resp[1] = (cmd->resp[1] << 8) | (cmd->resp[2] >> 24); + cmd->resp[2] = (cmd->resp[2] << 8) | (cmd->resp[3] >> 24); + cmd->resp[3] <<= 8; + } else if (cmd->flags & MMC_RSP_R3) { + cmd->resp[0] = cmd->resp[3]; + } + + if (stat & TMIO_STAT_CMDTIMEOUT) + cmd->error = -ETIMEDOUT; + else if (stat & TMIO_STAT_CRCFAIL && cmd->flags & MMC_RSP_CRC) + cmd->error = -EILSEQ; + + /* If there is data to handle we enable data IRQs here, and + * we will ultimatley finish the request in the data_end handler. + * If theres no data or we encountered an error, finish now. + */ + if (host->data && !cmd->error) { + if (host->data->flags & MMC_DATA_READ) + enable_mmc_irqs(ctl, TMIO_MASK_READOP); + else + enable_mmc_irqs(ctl, TMIO_MASK_WRITEOP); + } else { + tmio_mmc_finish_request(host); + } + + return; +} + + +static irqreturn_t tmio_mmc_irq(int irq, void *devid) +{ + struct tmio_mmc_host *host = devid; + void __iomem *ctl = host->ctl; + unsigned int ireg, irq_mask, status; + + pr_debug("MMC IRQ begin\n"); + + status = tmio_ioread32(ctl + CTL_STATUS); + irq_mask = tmio_ioread32(ctl + CTL_IRQ_MASK); + ireg = status & TMIO_MASK_IRQ & ~irq_mask; + + pr_debug_status(status); + pr_debug_status(ireg); + + if (!ireg) { + disable_mmc_irqs(ctl, status & ~irq_mask); + + pr_debug("tmio_mmc: Spurious irq, disabling! " + "0x%08x 0x%08x 0x%08x\n", status, irq_mask, ireg); + pr_debug_status(status); + + goto out; + } + + while (ireg) { + /* Card insert / remove attempts */ + if (ireg & (TMIO_STAT_CARD_INSERT | TMIO_STAT_CARD_REMOVE)) { + ack_mmc_irqs(ctl, TMIO_STAT_CARD_INSERT | + TMIO_STAT_CARD_REMOVE); + mmc_detect_change(host->mmc, 0); + } + + /* CRC and other errors */ +/* if (ireg & TMIO_STAT_ERR_IRQ) + * handled |= tmio_error_irq(host, irq, stat); + */ + + /* Command completion */ + if (ireg & TMIO_MASK_CMD) { + ack_mmc_irqs(ctl, TMIO_MASK_CMD); + tmio_mmc_cmd_irq(host, status); + } + + /* Data transfer */ + if (ireg & (TMIO_STAT_RXRDY | TMIO_STAT_TXRQ)) { + ack_mmc_irqs(ctl, TMIO_STAT_RXRDY | TMIO_STAT_TXRQ); + tmio_mmc_pio_irq(host); + } + + /* Data transfer completion */ + if (ireg & TMIO_STAT_DATAEND) { + ack_mmc_irqs(ctl, TMIO_STAT_DATAEND); + tmio_mmc_data_irq(host); + } + + /* Check status - keep going until we've handled it all */ + status = tmio_ioread32(ctl + CTL_STATUS); + irq_mask = tmio_ioread32(ctl + CTL_IRQ_MASK); + ireg = status & TMIO_MASK_IRQ & ~irq_mask; + + pr_debug("Status at end of loop: %08x\n", status); + pr_debug_status(status); + } + pr_debug("MMC IRQ end\n"); + +out: + return IRQ_HANDLED; +} + +static int tmio_mmc_start_data(struct tmio_mmc_host *host, + struct mmc_data *data) +{ + void __iomem *ctl = host->ctl; + + pr_debug("setup data transfer: blocksize %08x nr_blocks %d\n", + data->blksz, data->blocks); + + /* Hardware cannot perform 1 and 2 byte requests in 4 bit mode */ + if (data->blksz < 4 && host->mmc->ios.bus_width == MMC_BUS_WIDTH_4) { + printk(KERN_ERR "%s: %d byte block unsupported in 4 bit mode\n", + mmc_hostname(host->mmc), data->blksz); + return -EINVAL; + } + + tmio_mmc_init_sg(host, data); + host->data = data; + + /* Set transfer length / blocksize */ + tmio_iowrite16(data->blksz, ctl + CTL_SD_XFER_LEN); + tmio_iowrite16(data->blocks, ctl + CTL_XFER_BLK_COUNT); + + return 0; +} + +/* Process requests from the MMC layer */ +static void tmio_mmc_request(struct mmc_host *mmc, struct mmc_request *mrq) +{ + struct tmio_mmc_host *host = mmc_priv(mmc); + int ret; + + if (host->mrq) + pr_debug("request not null\n"); + + host->mrq = mrq; + + if (mrq->data) { + ret = tmio_mmc_start_data(host, mrq->data); + if (ret) + goto fail; + } + + ret = tmio_mmc_start_command(host, mrq->cmd); + + if (!ret) + return; + +fail: + mrq->cmd->error = ret; + mmc_request_done(mmc, mrq); +} + +/* Set MMC clock / power. + * Note: This controller uses a simple divider scheme therefore it cannot + * run a MMC card at full speed (20MHz). The max clock is 24MHz on SD, but as + * MMC wont run that fast, it has to be clocked at 12MHz which is the next + * slowest setting. + */ +static void tmio_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) +{ + struct tmio_mmc_host *host = mmc_priv(mmc); + void __iomem *cnf = host->cnf; + void __iomem *ctl = host->ctl; + + if (ios->clock) + tmio_mmc_set_clock(host, ios->clock); + + /* Power sequence - OFF -> ON -> UP */ + switch (ios->power_mode) { + case MMC_POWER_OFF: /* power down SD bus */ + tmio_iowrite8(0x00, cnf + CNF_PWR_CTL_2); + tmio_mmc_clk_stop(host); + break; + case MMC_POWER_ON: /* power up SD bus */ + + tmio_iowrite8(0x02, cnf + CNF_PWR_CTL_2); + break; + case MMC_POWER_UP: /* start bus clock */ + tmio_mmc_clk_start(host); + break; + } + + switch (ios->bus_width) { + case MMC_BUS_WIDTH_1: + tmio_iowrite16(0x80e0, ctl + CTL_SD_MEM_CARD_OPT); + break; + case MMC_BUS_WIDTH_4: + tmio_iowrite16(0x00e0, ctl + CTL_SD_MEM_CARD_OPT); + break; + } + + /* Let things settle. delay taken from winCE driver */ + udelay(140); +} + +static int tmio_mmc_get_ro(struct mmc_host *mmc) +{ + struct tmio_mmc_host *host = mmc_priv(mmc); + void __iomem *ctl = host->ctl; + + return (tmio_ioread16(ctl + CTL_STATUS) & TMIO_STAT_WRPROTECT) ? 0 : 1; +} + +static struct mmc_host_ops tmio_mmc_ops = { + .request = tmio_mmc_request, + .set_ios = tmio_mmc_set_ios, + .get_ro = tmio_mmc_get_ro, +}; + +#ifdef CONFIG_PM +static int tmio_mmc_suspend(struct platform_device *dev, pm_message_t state) +{ + struct mfd_cell *cell = (struct mfd_cell *)dev->dev.platform_data; + struct mmc_host *mmc = platform_get_drvdata(dev); + int ret; + + ret = mmc_suspend_host(mmc, state); + + /* Tell MFD core it can disable us now.*/ + if (!ret && cell->disable) + cell->disable(dev); + + return ret; +} + +static int tmio_mmc_resume(struct platform_device *dev) +{ + struct mfd_cell *cell = (struct mfd_cell *)dev->dev.platform_data; + struct mmc_host *mmc = platform_get_drvdata(dev); + struct tmio_mmc_host *host = mmc_priv(mmc); + void __iomem *cnf = host->cnf; + int ret = 0; + + /* Enable the MMC/SD Control registers */ + tmio_iowrite16(SDCREN, cnf + CNF_CMD); + tmio_iowrite32(dev->resource[0].start & 0xfffe, cnf + CNF_CTL_BASE); + + /* Tell the MFD core we are ready to be enabled */ + if (cell->enable) { + ret = cell->enable(dev); + if (ret) + goto out; + } + + mmc_resume_host(mmc); + +out: + return ret; +} +#else +#define tmio_mmc_suspend NULL +#define tmio_mmc_resume NULL +#endif + +static int __devinit tmio_mmc_probe(struct platform_device *dev) +{ + struct mfd_cell *cell = (struct mfd_cell *)dev->dev.platform_data; + struct resource *res_ctl, *res_cnf; + struct tmio_mmc_host *host; + struct mmc_host *mmc; + int ret = -ENOMEM; + + if (dev->num_resources != 3) + goto out; + + res_ctl = platform_get_resource(dev, IORESOURCE_MEM, 0); + res_cnf = platform_get_resource(dev, IORESOURCE_MEM, 1); + if (!res_ctl || !res_cnf) { + ret = -EINVAL; + goto out; + } + + mmc = mmc_alloc_host(sizeof(struct tmio_mmc_host), &dev->dev); + if (!mmc) + goto out; + + host = mmc_priv(mmc); + host->mmc = mmc; + platform_set_drvdata(dev, mmc); + + host->ctl = ioremap(res_ctl->start, res_ctl->end - res_ctl->start); + if (!host->ctl) + goto host_free; + + host->cnf = ioremap(res_cnf->start, res_cnf->end - res_cnf->start); + if (!host->cnf) + goto unmap_ctl; + + mmc->ops = &tmio_mmc_ops; + mmc->caps = MMC_CAP_4_BIT_DATA; + mmc->f_min = 46875; /* 24000000 / 512 */ + mmc->f_max = 24000000; + mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34; + + /* Enable the MMC/SD Control registers */ + tmio_iowrite16(SDCREN, host->cnf + CNF_CMD); + tmio_iowrite32(dev->resource[0].start & 0xfffe, + host->cnf + CNF_CTL_BASE); + + /* Tell the MFD core we are ready to be enabled */ + if (cell->enable) { + ret = cell->enable(dev); + if (ret) + goto unmap_cnf; + } + + /* Disable SD power during suspend */ + tmio_iowrite8(0x01, host->cnf + CNF_PWR_CTL_3); + + /* The below is required but why? FIXME */ + tmio_iowrite8(0x1f, host->cnf + CNF_STOP_CLK_CTL); + + /* Power down SD bus*/ + tmio_iowrite8(0x0, host->cnf + CNF_PWR_CTL_2); + + tmio_mmc_clk_stop(host); + reset(host); + + ret = platform_get_irq(dev, 0); + if (ret >= 0) + host->irq = ret; + else + goto unmap_cnf; + + disable_mmc_irqs(host->ctl, TMIO_MASK_ALL); + + ret = request_irq(host->irq, tmio_mmc_irq, IRQF_DISABLED, "tmio-mmc", + host); + if (ret) + goto unmap_cnf; + + set_irq_type(host->irq, IRQ_TYPE_EDGE_FALLING); + + mmc_add_host(mmc); + + printk(KERN_INFO "%s at 0x%08lx irq %d\n", mmc_hostname(host->mmc), + (unsigned long)host->ctl, host->irq); + + /* Unmask the IRQs we want to know about */ + enable_mmc_irqs(host->ctl, TMIO_MASK_IRQ); + + return 0; + +unmap_cnf: + iounmap(host->cnf); +unmap_ctl: + iounmap(host->ctl); +host_free: + mmc_free_host(mmc); +out: + return ret; +} + +static int __devexit tmio_mmc_remove(struct platform_device *dev) +{ + struct mmc_host *mmc = platform_get_drvdata(dev); + + platform_set_drvdata(dev, NULL); + + if (mmc) { + struct tmio_mmc_host *host = mmc_priv(mmc); + mmc_remove_host(mmc); + mmc_free_host(mmc); + free_irq(host->irq, host); + iounmap(host->ctl); + iounmap(host->cnf); + } + + return 0; +} + +/* ------------------- device registration ----------------------- */ + +static struct platform_driver tmio_mmc_driver = { + .driver = { + .name = "tmio-mmc", + .owner = THIS_MODULE, + }, + .probe = tmio_mmc_probe, + .remove = __devexit_p(tmio_mmc_remove), + .suspend = tmio_mmc_suspend, + .resume = tmio_mmc_resume, +}; + + +static int __init tmio_mmc_init(void) +{ + return platform_driver_register(&tmio_mmc_driver); +} + +static void __exit tmio_mmc_exit(void) +{ + platform_driver_unregister(&tmio_mmc_driver); +} + +module_init(tmio_mmc_init); +module_exit(tmio_mmc_exit); + +MODULE_DESCRIPTION("Toshiba TMIO SD/MMC driver"); +MODULE_AUTHOR("Ian Molton <spyro@f2s.com>"); +MODULE_LICENSE("GPL v2"); +MODULE_ALIAS("platform:tmio-mmc"); diff --git a/drivers/mmc/host/tmio_mmc.h b/drivers/mmc/host/tmio_mmc.h new file mode 100644 index 00000000000..9e647a06054 --- /dev/null +++ b/drivers/mmc/host/tmio_mmc.h @@ -0,0 +1,194 @@ +/* Definitons for use with the tmio_mmc.c + * + * (c) 2004 Ian Molton <spyro@f2s.com> + * (c) 2007 Ian Molton <spyro@f2s.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ +#define CNF_CMD 0x04 +#define CNF_CTL_BASE 0x10 +#define CNF_INT_PIN 0x3d +#define CNF_STOP_CLK_CTL 0x40 +#define CNF_GCLK_CTL 0x41 +#define CNF_SD_CLK_MODE 0x42 +#define CNF_PIN_STATUS 0x44 +#define CNF_PWR_CTL_1 0x48 +#define CNF_PWR_CTL_2 0x49 +#define CNF_PWR_CTL_3 0x4a +#define CNF_CARD_DETECT_MODE 0x4c +#define CNF_SD_SLOT 0x50 +#define CNF_EXT_GCLK_CTL_1 0xf0 +#define CNF_EXT_GCLK_CTL_2 0xf1 +#define CNF_EXT_GCLK_CTL_3 0xf9 +#define CNF_SD_LED_EN_1 0xfa +#define CNF_SD_LED_EN_2 0xfe + +#define SDCREN 0x2 /* Enable access to MMC CTL regs. (flag in COMMAND_REG)*/ + +#define CTL_SD_CMD 0x00 +#define CTL_ARG_REG 0x04 +#define CTL_STOP_INTERNAL_ACTION 0x08 +#define CTL_XFER_BLK_COUNT 0xa +#define CTL_RESPONSE 0x0c +#define CTL_STATUS 0x1c +#define CTL_IRQ_MASK 0x20 +#define CTL_SD_CARD_CLK_CTL 0x24 +#define CTL_SD_XFER_LEN 0x26 +#define CTL_SD_MEM_CARD_OPT 0x28 +#define CTL_SD_ERROR_DETAIL_STATUS 0x2c +#define CTL_SD_DATA_PORT 0x30 +#define CTL_TRANSACTION_CTL 0x34 +#define CTL_RESET_SD 0xe0 +#define CTL_SDIO_REGS 0x100 +#define CTL_CLK_AND_WAIT_CTL 0x138 +#define CTL_RESET_SDIO 0x1e0 + +/* Definitions for values the CTRL_STATUS register can take. */ +#define TMIO_STAT_CMDRESPEND 0x00000001 +#define TMIO_STAT_DATAEND 0x00000004 +#define TMIO_STAT_CARD_REMOVE 0x00000008 +#define TMIO_STAT_CARD_INSERT 0x00000010 +#define TMIO_STAT_SIGSTATE 0x00000020 +#define TMIO_STAT_WRPROTECT 0x00000080 +#define TMIO_STAT_CARD_REMOVE_A 0x00000100 +#define TMIO_STAT_CARD_INSERT_A 0x00000200 +#define TMIO_STAT_SIGSTATE_A 0x00000400 +#define TMIO_STAT_CMD_IDX_ERR 0x00010000 +#define TMIO_STAT_CRCFAIL 0x00020000 +#define TMIO_STAT_STOPBIT_ERR 0x00040000 +#define TMIO_STAT_DATATIMEOUT 0x00080000 +#define TMIO_STAT_RXOVERFLOW 0x00100000 +#define TMIO_STAT_TXUNDERRUN 0x00200000 +#define TMIO_STAT_CMDTIMEOUT 0x00400000 +#define TMIO_STAT_RXRDY 0x01000000 +#define TMIO_STAT_TXRQ 0x02000000 +#define TMIO_STAT_ILL_FUNC 0x20000000 +#define TMIO_STAT_CMD_BUSY 0x40000000 +#define TMIO_STAT_ILL_ACCESS 0x80000000 + +/* Define some IRQ masks */ +/* This is the mask used at reset by the chip */ +#define TMIO_MASK_ALL 0x837f031d +#define TMIO_MASK_READOP (TMIO_STAT_RXRDY | TMIO_STAT_DATAEND | \ + TMIO_STAT_CARD_REMOVE | TMIO_STAT_CARD_INSERT) +#define TMIO_MASK_WRITEOP (TMIO_STAT_TXRQ | TMIO_STAT_DATAEND | \ + TMIO_STAT_CARD_REMOVE | TMIO_STAT_CARD_INSERT) +#define TMIO_MASK_CMD (TMIO_STAT_CMDRESPEND | TMIO_STAT_CMDTIMEOUT | \ + TMIO_STAT_CARD_REMOVE | TMIO_STAT_CARD_INSERT) +#define TMIO_MASK_IRQ (TMIO_MASK_READOP | TMIO_MASK_WRITEOP | TMIO_MASK_CMD) + +#define enable_mmc_irqs(ctl, i) \ + do { \ + u32 mask;\ + mask = tmio_ioread32((ctl) + CTL_IRQ_MASK); \ + mask &= ~((i) & TMIO_MASK_IRQ); \ + tmio_iowrite32(mask, (ctl) + CTL_IRQ_MASK); \ + } while (0) + +#define disable_mmc_irqs(ctl, i) \ + do { \ + u32 mask;\ + mask = tmio_ioread32((ctl) + CTL_IRQ_MASK); \ + mask |= ((i) & TMIO_MASK_IRQ); \ + tmio_iowrite32(mask, (ctl) + CTL_IRQ_MASK); \ + } while (0) + +#define ack_mmc_irqs(ctl, i) \ + do { \ + u32 mask;\ + mask = tmio_ioread32((ctl) + CTL_STATUS); \ + mask &= ~((i) & TMIO_MASK_IRQ); \ + tmio_iowrite32(mask, (ctl) + CTL_STATUS); \ + } while (0) + + +struct tmio_mmc_host { + void __iomem *cnf; + void __iomem *ctl; + struct mmc_command *cmd; + struct mmc_request *mrq; + struct mmc_data *data; + struct mmc_host *mmc; + int irq; + + /* pio related stuff */ + struct scatterlist *sg_ptr; + unsigned int sg_len; + unsigned int sg_off; +}; + +#include <linux/scatterlist.h> +#include <linux/blkdev.h> + +static inline void tmio_mmc_init_sg(struct tmio_mmc_host *host, + struct mmc_data *data) +{ + host->sg_len = data->sg_len; + host->sg_ptr = data->sg; + host->sg_off = 0; +} + +static inline int tmio_mmc_next_sg(struct tmio_mmc_host *host) +{ + host->sg_ptr = sg_next(host->sg_ptr); + host->sg_off = 0; + return --host->sg_len; +} + +static inline char *tmio_mmc_kmap_atomic(struct tmio_mmc_host *host, + unsigned long *flags) +{ + struct scatterlist *sg = host->sg_ptr; + + local_irq_save(*flags); + return kmap_atomic(sg_page(sg), KM_BIO_SRC_IRQ) + sg->offset; +} + +static inline void tmio_mmc_kunmap_atomic(struct tmio_mmc_host *host, + unsigned long *flags) +{ + kunmap_atomic(sg_page(host->sg_ptr), KM_BIO_SRC_IRQ); + local_irq_restore(*flags); +} + +#ifdef CONFIG_MMC_DEBUG + +#define STATUS_TO_TEXT(a) \ + do { \ + if (status & TMIO_STAT_##a) \ + printf(#a); \ + } while (0) + +void debug_status(u32 status) +{ + printk(KERN_DEBUG "status: %08x = ", status); + STATUS_TO_TEXT(CARD_REMOVE); + STATUS_TO_TEXT(CARD_INSERT); + STATUS_TO_TEXT(SIGSTATE); + STATUS_TO_TEXT(WRPROTECT); + STATUS_TO_TEXT(CARD_REMOVE_A); + STATUS_TO_TEXT(CARD_INSERT_A); + STATUS_TO_TEXT(SIGSTATE_A); + STATUS_TO_TEXT(CMD_IDX_ERR); + STATUS_TO_TEXT(STOPBIT_ERR); + STATUS_TO_TEXT(ILL_FUNC); + STATUS_TO_TEXT(CMD_BUSY); + STATUS_TO_TEXT(CMDRESPEND); + STATUS_TO_TEXT(DATAEND); + STATUS_TO_TEXT(CRCFAIL); + STATUS_TO_TEXT(DATATIMEOUT); + STATUS_TO_TEXT(CMDTIMEOUT); + STATUS_TO_TEXT(RXOVERFLOW); + STATUS_TO_TEXT(TXUNDERRUN); + STATUS_TO_TEXT(RXRDY); + STATUS_TO_TEXT(TXRQ); + STATUS_TO_TEXT(ILL_ACCESS); + printk("\n"); +} + +#else +#define pr_debug_status(s) do { } while (0) +#endif |