summaryrefslogtreecommitdiffstats
path: root/drivers/mmc
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/mmc')
-rw-r--r--drivers/mmc/card/block.c36
-rw-r--r--drivers/mmc/card/queue.c11
-rw-r--r--drivers/mmc/core/core.c111
-rw-r--r--drivers/mmc/host/Kconfig30
-rw-r--r--drivers/mmc/host/Makefile5
-rw-r--r--drivers/mmc/host/atmel-mci-regs.h33
-rw-r--r--drivers/mmc/host/atmel-mci.c12
-rw-r--r--drivers/mmc/host/cb710-mmc.c804
-rw-r--r--drivers/mmc/host/cb710-mmc.h104
-rw-r--r--drivers/mmc/host/mmc_spi.c23
-rw-r--r--drivers/mmc/host/mmci.c6
-rw-r--r--drivers/mmc/host/mvsdio.c46
-rw-r--r--drivers/mmc/host/mxcmmc.c45
-rw-r--r--drivers/mmc/host/omap.c7
-rw-r--r--drivers/mmc/host/omap_hsmmc.c8
-rw-r--r--drivers/mmc/host/pxamci.c46
-rw-r--r--drivers/mmc/host/s3cmci.c5
-rw-r--r--drivers/mmc/host/sdhci-of.c9
-rw-r--r--drivers/mmc/host/sdhci-pci.c8
-rw-r--r--drivers/mmc/host/sdhci-pltfm.c168
-rw-r--r--drivers/mmc/host/sdhci.c58
-rw-r--r--drivers/mmc/host/sdhci.h4
-rw-r--r--drivers/mmc/host/tmio_mmc.c180
-rw-r--r--drivers/mmc/host/tmio_mmc.h77
24 files changed, 1580 insertions, 256 deletions
diff --git a/drivers/mmc/card/block.c b/drivers/mmc/card/block.c
index fe8041e619e..adc205c49fb 100644
--- a/drivers/mmc/card/block.c
+++ b/drivers/mmc/card/block.c
@@ -147,7 +147,8 @@ struct mmc_blk_request {
static u32 mmc_sd_num_wr_blocks(struct mmc_card *card)
{
int err;
- __be32 blocks;
+ u32 result;
+ __be32 *blocks;
struct mmc_request mrq;
struct mmc_command cmd;
@@ -199,14 +200,21 @@ static u32 mmc_sd_num_wr_blocks(struct mmc_card *card)
mrq.cmd = &cmd;
mrq.data = &data;
- sg_init_one(&sg, &blocks, 4);
+ blocks = kmalloc(4, GFP_KERNEL);
+ if (!blocks)
+ return (u32)-1;
+
+ sg_init_one(&sg, blocks, 4);
mmc_wait_for_req(card->host, &mrq);
+ result = ntohl(*blocks);
+ kfree(blocks);
+
if (cmd.error || data.error)
- return (u32)-1;
+ result = (u32)-1;
- return ntohl(blocks);
+ return result;
}
static u32 get_card_status(struct mmc_card *card, struct request *req)
@@ -243,7 +251,7 @@ static int mmc_blk_issue_rq(struct mmc_queue *mq, struct request *req)
brq.mrq.cmd = &brq.cmd;
brq.mrq.data = &brq.data;
- brq.cmd.arg = req->sector;
+ brq.cmd.arg = blk_rq_pos(req);
if (!mmc_card_blockaddr(card))
brq.cmd.arg <<= 9;
brq.cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_ADTC;
@@ -251,7 +259,15 @@ static int mmc_blk_issue_rq(struct mmc_queue *mq, struct request *req)
brq.stop.opcode = MMC_STOP_TRANSMISSION;
brq.stop.arg = 0;
brq.stop.flags = MMC_RSP_SPI_R1B | MMC_RSP_R1B | MMC_CMD_AC;
- brq.data.blocks = req->nr_sectors;
+ brq.data.blocks = blk_rq_sectors(req);
+
+ /*
+ * The block layer doesn't support all sector count
+ * restrictions, so we need to be prepared for too big
+ * requests.
+ */
+ if (brq.data.blocks > card->host->max_blk_count)
+ brq.data.blocks = card->host->max_blk_count;
/*
* After a read error, we redo the request one sector at a time
@@ -293,7 +309,7 @@ static int mmc_blk_issue_rq(struct mmc_queue *mq, struct request *req)
* Adjust the sg list so it is the same size as the
* request.
*/
- if (brq.data.blocks != req->nr_sectors) {
+ if (brq.data.blocks != blk_rq_sectors(req)) {
int i, data_size = brq.data.blocks << 9;
struct scatterlist *sg;
@@ -344,8 +360,8 @@ static int mmc_blk_issue_rq(struct mmc_queue *mq, struct request *req)
printk(KERN_ERR "%s: error %d transferring data,"
" sector %u, nr %u, card status %#x\n",
req->rq_disk->disk_name, brq.data.error,
- (unsigned)req->sector,
- (unsigned)req->nr_sectors, status);
+ (unsigned)blk_rq_pos(req),
+ (unsigned)blk_rq_sectors(req), status);
}
if (brq.stop.error) {
@@ -513,7 +529,7 @@ static struct mmc_blk_data *mmc_blk_alloc(struct mmc_card *card)
sprintf(md->disk->disk_name, "mmcblk%d", devidx);
- blk_queue_hardsect_size(md->queue.queue, 512);
+ blk_queue_logical_block_size(md->queue.queue, 512);
if (!mmc_card_sd(card) && mmc_card_blockaddr(card)) {
/*
diff --git a/drivers/mmc/card/queue.c b/drivers/mmc/card/queue.c
index 7a72e75d5c6..49e582356c6 100644
--- a/drivers/mmc/card/queue.c
+++ b/drivers/mmc/card/queue.c
@@ -55,7 +55,7 @@ static int mmc_queue_thread(void *d)
spin_lock_irq(q->queue_lock);
set_current_state(TASK_INTERRUPTIBLE);
if (!blk_queue_plugged(q))
- req = elv_next_request(q);
+ req = blk_fetch_request(q);
mq->req = req;
spin_unlock_irq(q->queue_lock);
@@ -88,16 +88,11 @@ static void mmc_request(struct request_queue *q)
{
struct mmc_queue *mq = q->queuedata;
struct request *req;
- int ret;
if (!mq) {
printk(KERN_ERR "MMC: killing requests for dead queue\n");
- while ((req = elv_next_request(q)) != NULL) {
- do {
- ret = __blk_end_request(req, -EIO,
- blk_rq_cur_bytes(req));
- } while (ret);
- }
+ while ((req = blk_fetch_request(q)) != NULL)
+ __blk_end_request_all(req, -EIO);
return;
}
diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c
index fa073ab3fa3..d84c880fac8 100644
--- a/drivers/mmc/core/core.c
+++ b/drivers/mmc/core/core.c
@@ -706,9 +706,15 @@ static void mmc_power_up(struct mmc_host *host)
* This delay should be sufficient to allow the power supply
* to reach the minimum voltage.
*/
- mmc_delay(2);
+ mmc_delay(10);
+
+ if (host->f_min > 400000) {
+ pr_warning("%s: Minimum clock frequency too high for "
+ "identification mode\n", mmc_hostname(host));
+ host->ios.clock = host->f_min;
+ } else
+ host->ios.clock = 400000;
- host->ios.clock = host->f_min;
host->ios.power_mode = MMC_POWER_ON;
mmc_set_ios(host);
@@ -716,7 +722,7 @@ static void mmc_power_up(struct mmc_host *host)
* This delay must be at least 74 clock sizes, or 1 ms, or the
* time required to reach a stable voltage.
*/
- mmc_delay(2);
+ mmc_delay(10);
}
static void mmc_power_off(struct mmc_host *host)
@@ -855,61 +861,72 @@ void mmc_rescan(struct work_struct *work)
mmc_bus_get(host);
- if (host->bus_ops == NULL) {
- /*
- * Only we can add a new handler, so it's safe to
- * release the lock here.
- */
+ /* if there is a card registered, check whether it is still present */
+ if ((host->bus_ops != NULL) && host->bus_ops->detect && !host->bus_dead)
+ host->bus_ops->detect(host);
+
+ mmc_bus_put(host);
+
+
+ mmc_bus_get(host);
+
+ /* if there still is a card present, stop here */
+ if (host->bus_ops != NULL) {
mmc_bus_put(host);
+ goto out;
+ }
- if (host->ops->get_cd && host->ops->get_cd(host) == 0)
- goto out;
+ /* detect a newly inserted card */
- mmc_claim_host(host);
+ /*
+ * Only we can add a new handler, so it's safe to
+ * release the lock here.
+ */
+ mmc_bus_put(host);
- mmc_power_up(host);
- mmc_go_idle(host);
+ if (host->ops->get_cd && host->ops->get_cd(host) == 0)
+ goto out;
- mmc_send_if_cond(host, host->ocr_avail);
+ mmc_claim_host(host);
- /*
- * First we search for SDIO...
- */
- err = mmc_send_io_op_cond(host, 0, &ocr);
- if (!err) {
- if (mmc_attach_sdio(host, ocr))
- mmc_power_off(host);
- goto out;
- }
+ mmc_power_up(host);
+ mmc_go_idle(host);
- /*
- * ...then normal SD...
- */
- err = mmc_send_app_op_cond(host, 0, &ocr);
- if (!err) {
- if (mmc_attach_sd(host, ocr))
- mmc_power_off(host);
- goto out;
- }
+ mmc_send_if_cond(host, host->ocr_avail);
- /*
- * ...and finally MMC.
- */
- err = mmc_send_op_cond(host, 0, &ocr);
- if (!err) {
- if (mmc_attach_mmc(host, ocr))
- mmc_power_off(host);
- goto out;
- }
+ /*
+ * First we search for SDIO...
+ */
+ err = mmc_send_io_op_cond(host, 0, &ocr);
+ if (!err) {
+ if (mmc_attach_sdio(host, ocr))
+ mmc_power_off(host);
+ goto out;
+ }
- mmc_release_host(host);
- mmc_power_off(host);
- } else {
- if (host->bus_ops->detect && !host->bus_dead)
- host->bus_ops->detect(host);
+ /*
+ * ...then normal SD...
+ */
+ err = mmc_send_app_op_cond(host, 0, &ocr);
+ if (!err) {
+ if (mmc_attach_sd(host, ocr))
+ mmc_power_off(host);
+ goto out;
+ }
- mmc_bus_put(host);
+ /*
+ * ...and finally MMC.
+ */
+ err = mmc_send_op_cond(host, 0, &ocr);
+ if (!err) {
+ if (mmc_attach_mmc(host, ocr))
+ mmc_power_off(host);
+ goto out;
}
+
+ mmc_release_host(host);
+ mmc_power_off(host);
+
out:
if (host->caps & MMC_CAP_NEEDS_POLL)
mmc_schedule_delayed_work(&host->detect, HZ);
diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
index b4cf691f3f6..40111a6d8d5 100644
--- a/drivers/mmc/host/Kconfig
+++ b/drivers/mmc/host/Kconfig
@@ -83,6 +83,17 @@ config MMC_SDHCI_OF
If unsure, say N.
+config MMC_SDHCI_PLTFM
+ tristate "SDHCI support on the platform specific bus"
+ depends on MMC_SDHCI
+ help
+ This selects the platform specific bus support for Secure Digital Host
+ Controller Interface.
+
+ If you have a controller with this interface, say Y or M here.
+
+ If unsure, say N.
+
config MMC_OMAP
tristate "TI OMAP Multimedia Card Interface support"
depends on ARCH_OMAP
@@ -155,7 +166,7 @@ config MMC_ATMELMCI_DMA
config MMC_IMX
tristate "Motorola i.MX Multimedia Card Interface support"
- depends on ARCH_IMX
+ depends on ARCH_MX1
help
This selects the Motorola i.MX Multimedia card Interface.
If you have a i.MX platform with a Multimedia Card slot,
@@ -237,7 +248,20 @@ config MMC_SDRICOH_CS
config MMC_TMIO
tristate "Toshiba Mobile IO Controller (TMIO) MMC/SD function support"
- depends on MFD_TMIO
+ depends on MFD_TMIO || MFD_ASIC3
help
This provides support for the SD/MMC cell found in TC6393XB,
- T7L66XB and also ipaq ASIC3
+ T7L66XB and also HTC ASIC3
+
+config MMC_CB710
+ tristate "ENE CB710 MMC/SD Interface support"
+ depends on PCI
+ select CB710_CORE
+ help
+ This option enables support for MMC/SD part of ENE CB710/720 Flash
+ memory card reader found in some laptops (ie. some versions of
+ HP Compaq nx9500).
+
+ This driver can also be built as a module. If so, the module
+ will be called cb710-mmc.
+
diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
index 970a997620e..79da397c5fe 100644
--- a/drivers/mmc/host/Makefile
+++ b/drivers/mmc/host/Makefile
@@ -14,6 +14,7 @@ obj-$(CONFIG_MMC_SDHCI) += sdhci.o
obj-$(CONFIG_MMC_SDHCI_PCI) += sdhci-pci.o
obj-$(CONFIG_MMC_RICOH_MMC) += ricoh_mmc.o
obj-$(CONFIG_MMC_SDHCI_OF) += sdhci-of.o
+obj-$(CONFIG_MMC_SDHCI_PLTFM) += sdhci-pltfm.o
obj-$(CONFIG_MMC_WBSD) += wbsd.o
obj-$(CONFIG_MMC_AU1X) += au1xmmc.o
obj-$(CONFIG_MMC_OMAP) += omap.o
@@ -29,4 +30,8 @@ endif
obj-$(CONFIG_MMC_S3C) += s3cmci.o
obj-$(CONFIG_MMC_SDRICOH_CS) += sdricoh_cs.o
obj-$(CONFIG_MMC_TMIO) += tmio_mmc.o
+obj-$(CONFIG_MMC_CB710) += cb710-mmc.o
+ifeq ($(CONFIG_CB710_DEBUG),y)
+ CFLAGS-cb710-mmc += -DDEBUG
+endif
diff --git a/drivers/mmc/host/atmel-mci-regs.h b/drivers/mmc/host/atmel-mci-regs.h
index b58364ed6bb..fc8a0fe7c5c 100644
--- a/drivers/mmc/host/atmel-mci-regs.h
+++ b/drivers/mmc/host/atmel-mci-regs.h
@@ -7,6 +7,12 @@
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
+
+/*
+ * Superset of MCI IP registers integrated in Atmel AVR32 and AT91 Processors
+ * Registers and bitfields marked with [2] are only available in MCI2
+ */
+
#ifndef __DRIVERS_MMC_ATMEL_MCI_H__
#define __DRIVERS_MMC_ATMEL_MCI_H__
@@ -14,11 +20,17 @@
#define MCI_CR 0x0000 /* Control */
# define MCI_CR_MCIEN ( 1 << 0) /* MCI Enable */
# define MCI_CR_MCIDIS ( 1 << 1) /* MCI Disable */
+# define MCI_CR_PWSEN ( 1 << 2) /* Power Save Enable */
+# define MCI_CR_PWSDIS ( 1 << 3) /* Power Save Disable */
# define MCI_CR_SWRST ( 1 << 7) /* Software Reset */
#define MCI_MR 0x0004 /* Mode */
# define MCI_MR_CLKDIV(x) ((x) << 0) /* Clock Divider */
+# define MCI_MR_PWSDIV(x) ((x) << 8) /* Power Saving Divider */
# define MCI_MR_RDPROOF ( 1 << 11) /* Read Proof */
# define MCI_MR_WRPROOF ( 1 << 12) /* Write Proof */
+# define MCI_MR_PDCFBYTE ( 1 << 13) /* Force Byte Transfer */
+# define MCI_MR_PDCPADV ( 1 << 14) /* Padding Value */
+# define MCI_MR_PDCMODE ( 1 << 15) /* PDC-oriented Mode */
#define MCI_DTOR 0x0008 /* Data Timeout */
# define MCI_DTOCYC(x) ((x) << 0) /* Data Timeout Cycles */
# define MCI_DTOMUL(x) ((x) << 4) /* Data Timeout Multiplier */
@@ -28,6 +40,7 @@
# define MCI_SDCSEL_MASK ( 3 << 0)
# define MCI_SDCBUS_1BIT ( 0 << 6) /* 1-bit data bus */
# define MCI_SDCBUS_4BIT ( 2 << 6) /* 4-bit data bus */
+# define MCI_SDCBUS_8BIT ( 3 << 6) /* 8-bit data bus[2] */
# define MCI_SDCBUS_MASK ( 3 << 6)
#define MCI_ARGR 0x0010 /* Command Argument */
#define MCI_CMDR 0x0014 /* Command */
@@ -56,6 +69,9 @@
#define MCI_BLKR 0x0018 /* Block */
# define MCI_BCNT(x) ((x) << 0) /* Data Block Count */
# define MCI_BLKLEN(x) ((x) << 16) /* Data Block Length */
+#define MCI_CSTOR 0x001c /* Completion Signal Timeout[2] */
+# define MCI_CSTOCYC(x) ((x) << 0) /* CST cycles */
+# define MCI_CSTOMUL(x) ((x) << 4) /* CST multiplier */
#define MCI_RSPR 0x0020 /* Response 0 */
#define MCI_RSPR1 0x0024 /* Response 1 */
#define MCI_RSPR2 0x0028 /* Response 2 */
@@ -83,7 +99,24 @@
# define MCI_DTOE ( 1 << 22) /* Data Time-Out Error */
# define MCI_OVRE ( 1 << 30) /* RX Overrun Error */
# define MCI_UNRE ( 1 << 31) /* TX Underrun Error */
+#define MCI_DMA 0x0050 /* DMA Configuration[2] */
+# define MCI_DMA_OFFSET(x) ((x) << 0) /* DMA Write Buffer Offset */
+# define MCI_DMA_CHKSIZE(x) ((x) << 4) /* DMA Channel Read and Write Chunk Size */
+# define MCI_DMAEN ( 1 << 8) /* DMA Hardware Handshaking Enable */
+#define MCI_CFG 0x0054 /* Configuration[2] */
+# define MCI_CFG_FIFOMODE_1DATA ( 1 << 0) /* MCI Internal FIFO control mode */
+# define MCI_CFG_FERRCTRL_COR ( 1 << 4) /* Flow Error flag reset control mode */
+# define MCI_CFG_HSMODE ( 1 << 8) /* High Speed Mode */
+# define MCI_CFG_LSYNC ( 1 << 12) /* Synchronize on the last block */
+#define MCI_WPMR 0x00e4 /* Write Protection Mode[2] */
+# define MCI_WP_EN ( 1 << 0) /* WP Enable */
+# define MCI_WP_KEY (0x4d4349 << 8) /* WP Key */
+#define MCI_WPSR 0x00e8 /* Write Protection Status[2] */
+# define MCI_GET_WP_VS(x) ((x) & 0x0f)
+# define MCI_GET_WP_VSRC(x) (((x) >> 8) & 0xffff)
+#define MCI_FIFO_APERTURE 0x0200 /* FIFO Aperture[2] */
+/* This is not including the FIFO Aperture on MCI2 */
#define MCI_REGS_SIZE 0x100
/* Register access macros */
diff --git a/drivers/mmc/host/atmel-mci.c b/drivers/mmc/host/atmel-mci.c
index cf6a100bb38..7b603e4b41d 100644
--- a/drivers/mmc/host/atmel-mci.c
+++ b/drivers/mmc/host/atmel-mci.c
@@ -177,6 +177,7 @@ struct atmel_mci {
* available.
* @wp_pin: GPIO pin used for card write protect sending, or negative
* if not available.
+ * @detect_is_active_high: The state of the detect pin when it is active.
* @detect_timer: Timer used for debouncing @detect_pin interrupts.
*/
struct atmel_mci_slot {
@@ -196,6 +197,7 @@ struct atmel_mci_slot {
int detect_pin;
int wp_pin;
+ bool detect_is_active_high;
struct timer_list detect_timer;
};
@@ -924,7 +926,8 @@ static int atmci_get_cd(struct mmc_host *mmc)
struct atmel_mci_slot *slot = mmc_priv(mmc);
if (gpio_is_valid(slot->detect_pin)) {
- present = !gpio_get_value(slot->detect_pin);
+ present = !(gpio_get_value(slot->detect_pin) ^
+ slot->detect_is_active_high);
dev_dbg(&mmc->class_dev, "card is %spresent\n",
present ? "" : "not ");
}
@@ -1028,7 +1031,8 @@ static void atmci_detect_change(unsigned long data)
return;
enable_irq(gpio_to_irq(slot->detect_pin));
- present = !gpio_get_value(slot->detect_pin);
+ present = !(gpio_get_value(slot->detect_pin) ^
+ slot->detect_is_active_high);
present_old = test_bit(ATMCI_CARD_PRESENT, &slot->flags);
dev_vdbg(&slot->mmc->class_dev, "detect change: %d (was %d)\n",
@@ -1456,6 +1460,7 @@ static int __init atmci_init_slot(struct atmel_mci *host,
slot->host = host;
slot->detect_pin = slot_data->detect_pin;
slot->wp_pin = slot_data->wp_pin;
+ slot->detect_is_active_high = slot_data->detect_is_active_high;
slot->sdc_reg = sdc_reg;
mmc->ops = &atmci_ops;
@@ -1477,7 +1482,8 @@ static int __init atmci_init_slot(struct atmel_mci *host,
if (gpio_request(slot->detect_pin, "mmc_detect")) {
dev_dbg(&mmc->class_dev, "no detect pin available\n");
slot->detect_pin = -EBUSY;
- } else if (gpio_get_value(slot->detect_pin)) {
+ } else if (gpio_get_value(slot->detect_pin) ^
+ slot->detect_is_active_high) {
clear_bit(ATMCI_CARD_PRESENT, &slot->flags);
}
}
diff --git a/drivers/mmc/host/cb710-mmc.c b/drivers/mmc/host/cb710-mmc.c
new file mode 100644
index 00000000000..11efefb1af5
--- /dev/null
+++ b/drivers/mmc/host/cb710-mmc.c
@@ -0,0 +1,804 @@
+/*
+ * cb710/mmc.c
+ *
+ * Copyright by Michał Mirosław, 2008-2009
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/pci.h>
+#include <linux/delay.h>
+#include "cb710-mmc.h"
+
+static const u8 cb710_clock_divider_log2[8] = {
+/* 1, 2, 4, 8, 16, 32, 128, 512 */
+ 0, 1, 2, 3, 4, 5, 7, 9
+};
+#define CB710_MAX_DIVIDER_IDX \
+ (ARRAY_SIZE(cb710_clock_divider_log2) - 1)
+
+static const u8 cb710_src_freq_mhz[16] = {
+ 33, 10, 20, 25, 30, 35, 40, 45,
+ 50, 55, 60, 65, 70, 75, 80, 85
+};
+
+static void cb710_mmc_set_clock(struct mmc_host *mmc, int hz)
+{
+ struct cb710_slot *slot = cb710_mmc_to_slot(mmc);
+ struct pci_dev *pdev = cb710_slot_to_chip(slot)->pdev;
+ u32 src_freq_idx;
+ u32 divider_idx;
+ int src_hz;
+
+ /* this is magic, unverifiable for me, unless I get
+ * MMC card with cables connected to bus signals */
+ pci_read_config_dword(pdev, 0x48, &src_freq_idx);
+ src_freq_idx = (src_freq_idx >> 16) & 0xF;
+ src_hz = cb710_src_freq_mhz[src_freq_idx] * 1000000;
+
+ for (divider_idx = 0; divider_idx < CB710_MAX_DIVIDER_IDX; ++divider_idx) {
+ if (hz >= src_hz >> cb710_clock_divider_log2[divider_idx])
+ break;
+ }
+
+ if (src_freq_idx)
+ divider_idx |= 0x8;
+
+ cb710_pci_update_config_reg(pdev, 0x40, ~0xF0000000, divider_idx << 28);
+
+ dev_dbg(cb710_slot_dev(slot),
+ "clock set to %d Hz, wanted %d Hz; flag = %d\n",
+ src_hz >> cb710_clock_divider_log2[divider_idx & 7],
+ hz, (divider_idx & 8) != 0);
+}
+
+static void __cb710_mmc_enable_irq(struct cb710_slot *slot,
+ unsigned short enable, unsigned short mask)
+{
+ /* clear global IE
+ * - it gets set later if any interrupt sources are enabled */
+ mask |= CB710_MMC_IE_IRQ_ENABLE;
+
+ /* look like interrupt is fired whenever
+ * WORD[0x0C] & WORD[0x10] != 0;
+ * -> bit 15 port 0x0C seems to be global interrupt enable
+ */
+
+ enable = (cb710_read_port_16(slot, CB710_MMC_IRQ_ENABLE_PORT)
+ & ~mask) | enable;
+
+ if (enable)
+ enable |= CB710_MMC_IE_IRQ_ENABLE;
+
+ cb710_write_port_16(slot, CB710_MMC_IRQ_ENABLE_PORT, enable);
+}
+
+static void cb710_mmc_enable_irq(struct cb710_slot *slot,
+ unsigned short enable, unsigned short mask)
+{
+ struct cb710_mmc_reader *reader = mmc_priv(cb710_slot_to_mmc(slot));
+ unsigned long flags;
+
+ spin_lock_irqsave(&reader->irq_lock, flags);
+ /* this is the only thing irq_lock protects */
+ __cb710_mmc_enable_irq(slot, enable, mask);
+ spin_unlock_irqrestore(&reader->irq_lock, flags);
+}
+
+static void cb710_mmc_reset_events(struct cb710_slot *slot)
+{
+ cb710_write_port_8(slot, CB710_MMC_STATUS0_PORT, 0xFF);
+ cb710_write_port_8(slot, CB710_MMC_STATUS1_PORT, 0xFF);
+ cb710_write_port_8(slot, CB710_MMC_STATUS2_PORT, 0xFF);
+}
+
+static int cb710_mmc_is_card_inserted(struct cb710_slot *slot)
+{
+ return cb710_read_port_8(slot, CB710_MMC_STATUS3_PORT)
+ & CB710_MMC_S3_CARD_DETECTED;
+}
+
+static void cb710_mmc_enable_4bit_data(struct cb710_slot *slot, int enable)
+{
+ dev_dbg(cb710_slot_dev(slot), "configuring %d-data-line%s mode\n",
+ enable ? 4 : 1, enable ? "s" : "");
+ if (enable)
+ cb710_modify_port_8(slot, CB710_MMC_CONFIG1_PORT,
+ CB710_MMC_C1_4BIT_DATA_BUS, 0);
+ else
+ cb710_modify_port_8(slot, CB710_MMC_CONFIG1_PORT,
+ 0, CB710_MMC_C1_4BIT_DATA_BUS);
+}
+
+static int cb710_check_event(struct cb710_slot *slot, u8 what)
+{
+ u16 status;
+
+ status = cb710_read_port_16(slot, CB710_MMC_STATUS_PORT);
+
+ if (status & CB710_MMC_S0_FIFO_UNDERFLOW) {
+ /* it is just a guess, so log it */
+ dev_dbg(cb710_slot_dev(slot),
+ "CHECK : ignoring bit 6 in status %04X\n", status);
+ cb710_write_port_8(slot, CB710_MMC_STATUS0_PORT,
+ CB710_MMC_S0_FIFO_UNDERFLOW);
+ status &= ~CB710_MMC_S0_FIFO_UNDERFLOW;
+ }
+
+ if (status & CB710_MMC_STATUS_ERROR_EVENTS) {
+ dev_dbg(cb710_slot_dev(slot),
+ "CHECK : returning EIO on status %04X\n", status);
+ cb710_write_port_8(slot, CB710_MMC_STATUS0_PORT, status & 0xFF);
+ cb710_write_port_8(slot, CB710_MMC_STATUS1_PORT,
+ CB710_MMC_S1_RESET);
+ return -EIO;
+ }
+
+ /* 'what' is a bit in MMC_STATUS1 */
+ if ((status >> 8) & what) {
+ cb710_write_port_8(slot, CB710_MMC_STATUS1_PORT, what);
+ return 1;
+ }
+
+ return 0;
+}
+
+static int cb710_wait_for_event(struct cb710_slot *slot, u8 what)
+{
+ int err = 0;
+ unsigned limit = 2000000; /* FIXME: real timeout */
+
+#ifdef CONFIG_CB710_DEBUG
+ u32 e, x;
+ e = cb710_read_port_32(slot, CB710_MMC_STATUS_PORT);
+#endif
+
+ while (!(err = cb710_check_event(slot, what))) {
+ if (!--limit) {
+ cb710_dump_regs(cb710_slot_to_chip(slot),
+ CB710_DUMP_REGS_MMC);
+ err = -ETIMEDOUT;
+ break;
+ }
+ udelay(1);
+ }
+
+#ifdef CONFIG_CB710_DEBUG
+ x = cb710_read_port_32(slot, CB710_MMC_STATUS_PORT);
+
+ limit = 2000000 - limit;
+ if (limit > 100)
+ dev_dbg(cb710_slot_dev(slot),
+ "WAIT10: waited %d loops, what %d, entry val %08X, exit val %08X\n",
+ limit, what, e, x);
+#endif
+ return err < 0 ? err : 0;
+}
+
+
+static int cb710_wait_while_busy(struct cb710_slot *slot, uint8_t mask)
+{
+ unsigned limit = 500000; /* FIXME: real timeout */
+ int err = 0;
+
+#ifdef CONFIG_CB710_DEBUG
+ u32 e, x;
+ e = cb710_read_port_32(slot, CB710_MMC_STATUS_PORT);
+#endif
+
+ while (cb710_read_port_8(slot, CB710_MMC_STATUS2_PORT) & mask) {
+ if (!--limit) {
+ cb710_dump_regs(cb710_slot_to_chip(slot),
+ CB710_DUMP_REGS_MMC);
+ err = -ETIMEDOUT;
+ break;
+ }
+ udelay(1);
+ }
+
+#ifdef CONFIG_CB710_DEBUG
+ x = cb710_read_port_32(slot, CB710_MMC_STATUS_PORT);
+
+ limit = 500000 - limit;
+ if (limit > 100)
+ dev_dbg(cb710_slot_dev(slot),
+ "WAIT12: waited %d loops, mask %02X, entry val %08X, exit val %08X\n",
+ limit, mask, e, x);
+#endif
+ return 0;
+}
+
+static void cb710_mmc_set_transfer_size(struct cb710_slot *slot,
+ size_t count, size_t blocksize)
+{
+ cb710_wait_while_busy(slot, CB710_MMC_S2_BUSY_20);
+ cb710_write_port_32(slot, CB710_MMC_TRANSFER_SIZE_PORT,
+ ((count - 1) << 16)|(blocksize - 1));
+
+ dev_vdbg(cb710_slot_dev(slot), "set up for %zu block%s of %zu bytes\n",
+ count, count == 1 ? "" : "s", blocksize);
+}
+
+static void cb710_mmc_fifo_hack(struct cb710_slot *slot)
+{
+ /* without this, received data is prepended with 8-bytes of zeroes */
+ u32 r1, r2;
+ int ok = 0;
+
+ r1 = cb710_read_port_32(slot, CB710_MMC_DATA_PORT);
+ r2 = cb710_read_port_32(slot, CB710_MMC_DATA_PORT);
+ if (cb710_read_port_8(slot, CB710_MMC_STATUS0_PORT)
+ & CB710_MMC_S0_FIFO_UNDERFLOW) {
+ cb710_write_port_8(slot, CB710_MMC_STATUS0_PORT,
+ CB710_MMC_S0_FIFO_UNDERFLOW);
+ ok = 1;
+ }
+
+ dev_dbg(cb710_slot_dev(slot),
+ "FIFO-read-hack: expected STATUS0 bit was %s\n",
+ ok ? "set." : "NOT SET!");
+ dev_dbg(cb710_slot_dev(slot),
+ "FIFO-read-hack: dwords ignored: %08X %08X - %s\n",
+ r1, r2, (r1|r2) ? "BAD (NOT ZERO)!" : "ok");
+}
+
+static int cb710_mmc_receive_pio(struct cb710_slot *slot,
+ struct sg_mapping_iter *miter, size_t dw_count)
+{
+ if (!(cb710_read_port_8(slot, CB710_MMC_STATUS2_PORT) & CB710_MMC_S2_FIFO_READY)) {
+ int err = cb710_wait_for_event(slot,
+ CB710_MMC_S1_PIO_TRANSFER_DONE);
+ if (err)
+ return err;
+ }
+
+ cb710_sg_dwiter_write_from_io(miter,
+ slot->iobase + CB710_MMC_DATA_PORT, dw_count);
+
+ return 0;
+}
+
+static bool cb710_is_transfer_size_supported(struct mmc_data *data)
+{
+ return !(data->blksz & 15 && (data->blocks != 1 || data->blksz != 8));
+}
+
+static int cb710_mmc_receive(struct cb710_slot *slot, struct mmc_data *data)
+{
+ struct sg_mapping_iter miter;
+ size_t len, blocks = data->blocks;
+ int err = 0;
+
+ /* TODO: I don't know how/if the hardware handles non-16B-boundary blocks
+ * except single 8B block */
+ if (unlikely(data->blksz & 15 && (data->blocks != 1 || data->blksz != 8)))
+ return -EINVAL;
+
+ sg_miter_start(&miter, data->sg, data->sg_len, 0);
+
+ cb710_modify_port_8(slot, CB710_MMC_CONFIG2_PORT,
+ 15, CB710_MMC_C2_READ_PIO_SIZE_MASK);
+
+ cb710_mmc_fifo_hack(slot);
+
+ while (blocks-- > 0) {
+ len = data->blksz;
+
+ while (len >= 16) {
+ err = cb710_mmc_receive_pio(slot, &miter, 4);
+ if (err)
+ goto out;
+ len -= 16;
+ }
+
+ if (!len)
+ continue;
+
+ cb710_modify_port_8(slot, CB710_MMC_CONFIG2_PORT,
+ len - 1, CB710_MMC_C2_READ_PIO_SIZE_MASK);
+
+ len = (len >= 8) ? 4 : 2;
+ err = cb710_mmc_receive_pio(slot, &miter, len);
+ if (err)
+ goto out;
+ }
+out:
+ cb710_sg_miter_stop_writing(&miter);
+ return err;
+}
+
+static int cb710_mmc_send(struct cb710_slot *slot, struct mmc_data *data)
+{
+ struct sg_mapping_iter miter;
+ size_t len, blocks = data->blocks;
+ int err = 0;
+
+ /* TODO: I don't know how/if the hardware handles multiple
+ * non-16B-boundary blocks */
+ if (unlikely(data->blocks > 1 && data->blksz & 15))
+ return -EINVAL;
+
+ sg_miter_start(&miter, data->sg, data->sg_len, 0);
+
+ cb710_modify_port_8(slot, CB710_MMC_CONFIG2_PORT,
+ 0, CB710_MMC_C2_READ_PIO_SIZE_MASK);
+
+ while (blocks-- > 0) {
+ len = (data->blksz + 15) >> 4;
+ do {
+ if (!(cb710_read_port_8(slot, CB710_MMC_STATUS2_PORT)
+ & CB710_MMC_S2_FIFO_EMPTY)) {
+ err = cb710_wait_for_event(slot,
+ CB710_MMC_S1_PIO_TRANSFER_DONE);
+ if (err)
+ goto out;
+ }
+ cb710_sg_dwiter_read_to_io(&miter,
+ slot->iobase + CB710_MMC_DATA_PORT, 4);
+ } while (--len);
+ }
+out:
+ sg_miter_stop(&miter);
+ return err;
+}
+
+static u16 cb710_encode_cmd_flags(struct cb710_mmc_reader *reader,
+ struct mmc_command *cmd)
+{
+ unsigned int flags = cmd->flags;
+ u16 cb_flags = 0;
+
+ /* Windows driver returned 0 for commands for which no response
+ * is expected. It happened that there were only two such commands
+ * used: MMC_GO_IDLE_STATE and MMC_GO_INACTIVE_STATE so it might
+ * as well be a bug in that driver.
+ *
+ * Original driver set bit 14 for MMC/SD application
+ * commands. There's no difference 'on the wire' and
+ * it apparently works without it anyway.
+ */
+
+ switch (flags & MMC_CMD_MASK) {
+ case MMC_CMD_AC: cb_flags = CB710_MMC_CMD_AC; break;
+ case MMC_CMD_ADTC: cb_flags = CB710_MMC_CMD_ADTC; break;
+ case MMC_CMD_BC: cb_flags = CB710_MMC_CMD_BC; break;
+ case MMC_CMD_BCR: cb_flags = CB710_MMC_CMD_BCR; break;
+ }
+
+ if (flags & MMC_RSP_BUSY)
+ cb_flags |= CB710_MMC_RSP_BUSY;
+
+ cb_flags |= cmd->opcode << CB710_MMC_CMD_CODE_SHIFT;
+
+ if (cmd->data && (cmd->data->flags & MMC_DATA_READ))
+ cb_flags |= CB710_MMC_DATA_READ;
+
+ if (flags & MMC_RSP_PRESENT) {
+ /* Windows driver set 01 at bits 4,3 except for
+ * MMC_SET_BLOCKLEN where it set 10. Maybe the
+ * hardware can do something special about this
+ * command? The original driver looks buggy/incomplete
+ * anyway so we ignore this for now.
+ *
+ * I assume that 00 here means no response is expected.
+ */
+ cb_flags |= CB710_MMC_RSP_PRESENT;
+
+ if (flags & MMC_RSP_136)
+ cb_flags |= CB710_MMC_RSP_136;
+ if (!(flags & MMC_RSP_CRC))
+ cb_flags |= CB710_MMC_RSP_NO_CRC;
+ }
+
+ return cb_flags;
+}
+
+static void cb710_receive_response(struct cb710_slot *slot,
+ struct mmc_command *cmd)
+{
+ unsigned rsp_opcode, wanted_opcode;
+
+ /* Looks like final byte with CRC is always stripped (same as SDHCI) */
+ if (cmd->flags & MMC_RSP_136) {
+ u32 resp[4];
+
+ resp[0] = cb710_read_port_32(slot, CB710_MMC_RESPONSE3_PORT);
+ resp[1] = cb710_read_port_32(slot, CB710_MMC_RESPONSE2_PORT);
+ resp[2] = cb710_read_port_32(slot, CB710_MMC_RESPONSE1_PORT);
+ resp[3] = cb710_read_port_32(slot, CB710_MMC_RESPONSE0_PORT);
+ rsp_opcode = resp[0] >> 24;
+
+ cmd->resp[0] = (resp[0] << 8)|(resp[1] >> 24);
+ cmd->resp[1] = (resp[1] << 8)|(resp[2] >> 24);
+ cmd->resp[2] = (resp[2] << 8)|(resp[3] >> 24);
+ cmd->resp[3] = (resp[3] << 8);
+ } else {
+ rsp_opcode = cb710_read_port_32(slot, CB710_MMC_RESPONSE1_PORT) & 0x3F;
+ cmd->resp[0] = cb710_read_port_32(slot, CB710_MMC_RESPONSE0_PORT);
+ }
+
+ wanted_opcode = (cmd->flags & MMC_RSP_OPCODE) ? cmd->opcode : 0x3F;
+ if (rsp_opcode != wanted_opcode)
+ cmd->error = -EILSEQ;
+}
+
+static int cb710_mmc_transfer_data(struct cb710_slot *slot,
+ struct mmc_data *data)
+{
+ int error, to;
+
+ if (data->flags & MMC_DATA_READ)
+ error = cb710_mmc_receive(slot, data);
+ else
+ error = cb710_mmc_send(slot, data);
+
+ to = cb710_wait_for_event(slot, CB710_MMC_S1_DATA_TRANSFER_DONE);
+ if (!error)
+ error = to;
+
+ if (!error)
+ data->bytes_xfered = data->blksz * data->blocks;
+ return error;
+}
+
+static int cb710_mmc_command(struct mmc_host *mmc, struct mmc_command *cmd)
+{
+ struct cb710_slot *slot = cb710_mmc_to_slot(mmc);
+ struct cb710_mmc_reader *reader = mmc_priv(mmc);
+ struct mmc_data *data = cmd->data;
+
+ u16 cb_cmd = cb710_encode_cmd_flags(reader, cmd);
+ dev_dbg(cb710_slot_dev(slot), "cmd request: 0x%04X\n", cb_cmd);
+
+ if (data) {
+ if (!cb710_is_transfer_size_supported(data)) {
+ data->error = -EINVAL;
+ return -1;
+ }
+ cb710_mmc_set_transfer_size(slot, data->blocks, data->blksz);
+ }
+
+ cb710_wait_while_busy(slot, CB710_MMC_S2_BUSY_20|CB710_MMC_S2_BUSY_10);
+ cb710_write_port_16(slot, CB710_MMC_CMD_TYPE_PORT, cb_cmd);
+ cb710_wait_while_busy(slot, CB710_MMC_S2_BUSY_20);
+ cb710_write_port_32(slot, CB710_MMC_CMD_PARAM_PORT, cmd->arg);
+ cb710_mmc_reset_events(slot);
+ cb710_wait_while_busy(slot, CB710_MMC_S2_BUSY_20);
+ cb710_modify_port_8(slot, CB710_MMC_CONFIG0_PORT, 0x01, 0);
+
+ cmd->error = cb710_wait_for_event(slot, CB710_MMC_S1_COMMAND_SENT);
+ if (cmd->error)
+ return -1;
+
+ if (cmd->flags & MMC_RSP_PRESENT) {
+ cb710_receive_response(slot, cmd);
+ if (cmd->error)
+ return -1;
+ }
+
+ if (data)
+ data->error = cb710_mmc_transfer_data(slot, data);
+ return 0;
+}
+
+static void cb710_mmc_request(struct mmc_host *mmc, struct mmc_request *mrq)
+{
+ struct cb710_slot *slot = cb710_mmc_to_slot(mmc);
+ struct cb710_mmc_reader *reader = mmc_priv(mmc);
+
+ WARN_ON(reader->mrq != NULL);
+
+ reader->mrq = mrq;
+ cb710_mmc_enable_irq(slot, CB710_MMC_IE_TEST_MASK, 0);
+
+ if (cb710_mmc_is_card_inserted(slot)) {
+ if (!cb710_mmc_command(mmc, mrq->cmd) && mrq->stop)
+ cb710_mmc_command(mmc, mrq->stop);
+ mdelay(1);
+ } else {
+ mrq->cmd->error = -ENOMEDIUM;
+ }
+
+ tasklet_schedule(&reader->finish_req_tasklet);
+}
+
+static int cb710_mmc_powerup(struct cb710_slot *slot)
+{
+#ifdef CONFIG_CB710_DEBUG
+ struct cb710_chip *chip = cb710_slot_to_chip(slot);
+#endif
+ int err;
+
+ /* a lot of magic; see comment in cb710_mmc_set_clock() */
+ dev_dbg(cb710_slot_dev(slot), "bus powerup\n");
+ cb710_dump_regs(chip, CB710_DUMP_REGS_MMC);
+ err = cb710_wait_while_busy(slot, CB710_MMC_S2_BUSY_20);
+ if (unlikely(err))
+ return err;
+ cb710_modify_port_8(slot, CB710_MMC_CONFIG1_PORT, 0x80, 0);
+ cb710_modify_port_8(slot, CB710_MMC_CONFIG3_PORT, 0x80, 0);
+ cb710_dump_regs(chip, CB710_DUMP_REGS_MMC);
+ mdelay(1);
+ dev_dbg(cb710_slot_dev(slot), "after delay 1\n");
+ cb710_dump_regs(chip, CB710_DUMP_REGS_MMC);
+ err = cb710_wait_while_busy(slot, CB710_MMC_S2_BUSY_20);
+ if (unlikely(err))
+ return err;
+ cb710_modify_port_8(slot, CB710_MMC_CONFIG1_PORT, 0x09, 0);
+ cb710_dump_regs(chip, CB710_DUMP_REGS_MMC);
+ mdelay(1);
+ dev_dbg(cb710_slot_dev(slot), "after delay 2\n");
+ cb710_dump_regs(chip, CB710_DUMP_REGS_MMC);
+ err = cb710_wait_while_busy(slot, CB710_MMC_S2_BUSY_20);
+ if (unlikely(err))
+ return err;
+ cb710_modify_port_8(slot, CB710_MMC_CONFIG1_PORT, 0, 0x08);
+ cb710_dump_regs(chip, CB710_DUMP_REGS_MMC);
+ mdelay(2);
+ dev_dbg(cb710_slot_dev(slot), "after delay 3\n");
+ cb710_dump_regs(chip, CB710_DUMP_REGS_MMC);
+ cb710_modify_port_8(slot, CB710_MMC_CONFIG0_PORT, 0x06, 0);
+ cb710_modify_port_8(slot, CB710_MMC_CONFIG1_PORT, 0x70, 0);
+ cb710_modify_port_8(slot, CB710_MMC_CONFIG2_PORT, 0x80, 0);
+ cb710_modify_port_8(slot, CB710_MMC_CONFIG3_PORT, 0x03, 0);
+ cb710_dump_regs(chip, CB710_DUMP_REGS_MMC);
+ err = cb710_wait_while_busy(slot, CB710_MMC_S2_BUSY_20);
+ if (unlikely(err))
+ return err;
+ /* This port behaves weird: quick byte reads of 0x08,0x09 return
+ * 0xFF,0x00 after writing 0xFFFF to 0x08; it works correctly when
+ * read/written from userspace... What am I missing here?
+ * (it doesn't depend on write-to-read delay) */
+ cb710_write_port_16(slot, CB710_MMC_CONFIGB_PORT, 0xFFFF);
+ cb710_modify_port_8(slot, CB710_MMC_CONFIG0_PORT, 0x06, 0);
+ cb710_dump_regs(chip, CB710_DUMP_REGS_MMC);
+ dev_dbg(cb710_slot_dev(slot), "bus powerup finished\n");
+
+ return cb710_check_event(slot, 0);
+}
+
+static void cb710_mmc_powerdown(struct cb710_slot *slot)
+{
+ cb710_modify_port_8(slot, CB710_MMC_CONFIG1_PORT, 0, 0x81);
+ cb710_modify_port_8(slot, CB710_MMC_CONFIG3_PORT, 0, 0x80);
+}
+
+static void cb710_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
+{
+ struct cb710_slot *slot = cb710_mmc_to_slot(mmc);
+ struct cb710_mmc_reader *reader = mmc_priv(mmc);
+ int err;
+
+ cb710_mmc_set_clock(mmc, ios->clock);
+
+ if (!cb710_mmc_is_card_inserted(slot)) {
+ dev_dbg(cb710_slot_dev(slot),
+ "no card inserted - ignoring bus powerup request\n");
+ ios->power_mode = MMC_POWER_OFF;
+ }
+
+ if (ios->power_mode != reader->last_power_mode)
+ switch (ios->power_mode) {
+ case MMC_POWER_ON:
+ err = cb710_mmc_powerup(slot);
+ if (err) {
+ dev_warn(cb710_slot_dev(slot),
+ "powerup failed (%d)- retrying\n", err);
+ cb710_mmc_powerdown(slot);
+ udelay(1);
+ err = cb710_mmc_powerup(slot);
+ if (err)
+ dev_warn(cb710_slot_dev(slot),
+ "powerup retry failed (%d) - expect errors\n",
+ err);
+ }
+ reader->last_power_mode = MMC_POWER_ON;
+ break;
+ case MMC_POWER_OFF:
+ cb710_mmc_powerdown(slot);
+ reader->last_power_mode = MMC_POWER_OFF;
+ break;
+ case MMC_POWER_UP:
+ default:
+ /* ignore */;
+ }
+
+ cb710_mmc_enable_4bit_data(slot, ios->bus_width != MMC_BUS_WIDTH_1);
+
+ cb710_mmc_enable_irq(slot, CB710_MMC_IE_TEST_MASK, 0);
+}
+
+static int cb710_mmc_get_ro(struct mmc_host *mmc)
+{
+ struct cb710_slot *slot = cb710_mmc_to_slot(mmc);
+
+ return cb710_read_port_8(slot, CB710_MMC_STATUS3_PORT)
+ & CB710_MMC_S3_WRITE_PROTECTED;
+}
+
+static int cb710_mmc_irq_handler(struct cb710_slot *slot)
+{
+ struct mmc_host *mmc = cb710_slot_to_mmc(slot);
+ struct cb710_mmc_reader *reader = mmc_priv(mmc);
+ u32 status, config1, config2, irqen;
+
+ status = cb710_read_port_32(slot, CB710_MMC_STATUS_PORT);
+ irqen = cb710_read_port_32(slot, CB710_MMC_IRQ_ENABLE_PORT);
+ config2 = cb710_read_port_32(slot, CB710_MMC_CONFIGB_PORT);
+ config1 = cb710_read_port_32(slot, CB710_MMC_CONFIG_PORT);
+
+ dev_dbg(cb710_slot_dev(slot), "interrupt; status: %08X, "
+ "ie: %08X, c2: %08X, c1: %08X\n",
+ status, irqen, config2, config1);
+
+ if (status & (CB710_MMC_S1_CARD_CHANGED << 8)) {
+ /* ack the event */
+ cb710_write_port_8(slot, CB710_MMC_STATUS1_PORT,
+ CB710_MMC_S1_CARD_CHANGED);
+ if ((irqen & CB710_MMC_IE_CISTATUS_MASK)
+ == CB710_MMC_IE_CISTATUS_MASK)
+ mmc_detect_change(mmc, HZ/5);
+ } else {
+ dev_dbg(cb710_slot_dev(slot), "unknown interrupt (test)\n");
+ spin_lock(&reader->irq_lock);
+ __cb710_mmc_enable_irq(slot, 0, CB710_MMC_IE_TEST_MASK);
+ spin_unlock(&reader->irq_lock);
+ }
+
+ return 1;
+}
+
+static void cb710_mmc_finish_request_tasklet(unsigned long data)
+{
+ struct mmc_host *mmc = (void *)data;
+ struct cb710_mmc_reader *reader = mmc_priv(mmc);
+ struct mmc_request *mrq = reader->mrq;
+
+ reader->mrq = NULL;
+ mmc_request_done(mmc, mrq);
+}
+
+static const struct mmc_host_ops cb710_mmc_host = {
+ .request = cb710_mmc_request,
+ .set_ios = cb710_mmc_set_ios,
+ .get_ro = cb710_mmc_get_ro
+};
+
+#ifdef CONFIG_PM
+
+static int cb710_mmc_suspend(struct platform_device *pdev, pm_message_t state)
+{
+ struct cb710_slot *slot = cb710_pdev_to_slot(pdev);
+ struct mmc_host *mmc = cb710_slot_to_mmc(slot);
+ int err;
+
+ err = mmc_suspend_host(mmc, state);
+ if (err)
+ return err;
+
+ cb710_mmc_enable_irq(slot, 0, ~0);
+ return 0;
+}
+
+static int cb710_mmc_resume(struct platform_device *pdev)
+{
+ struct cb710_slot *slot = cb710_pdev_to_slot(pdev);
+ struct mmc_host *mmc = cb710_slot_to_mmc(slot);
+
+ cb710_mmc_enable_irq(slot, 0, ~0);
+
+ return mmc_resume_host(mmc);
+}
+
+#endif /* CONFIG_PM */
+
+static int __devinit cb710_mmc_init(struct platform_device *pdev)
+{
+ struct cb710_slot *slot = cb710_pdev_to_slot(pdev);
+ struct cb710_chip *chip = cb710_slot_to_chip(slot);
+ struct mmc_host *mmc;
+ struct cb710_mmc_reader *reader;
+ int err;
+ u32 val;
+
+ mmc = mmc_alloc_host(sizeof(*reader), cb710_slot_dev(slot));
+ if (!mmc)
+ return -ENOMEM;
+
+ dev_set_drvdata(&pdev->dev, mmc);
+
+ /* harmless (maybe) magic */
+ pci_read_config_dword(chip->pdev, 0x48, &val);
+ val = cb710_src_freq_mhz[(val >> 16) & 0xF];
+ dev_dbg(cb710_slot_dev(slot), "source frequency: %dMHz\n", val);
+ val *= 1000000;
+
+ mmc->ops = &cb710_mmc_host;
+ mmc->f_max = val;
+ mmc->f_min = val >> cb710_clock_divider_log2[CB710_MAX_DIVIDER_IDX];
+ mmc->ocr_avail = MMC_VDD_32_33|MMC_VDD_33_34;
+ mmc->caps = MMC_CAP_4_BIT_DATA;
+
+ reader = mmc_priv(mmc);
+
+ tasklet_init(&reader->finish_req_tasklet,
+ cb710_mmc_finish_request_tasklet, (unsigned long)mmc);
+ spin_lock_init(&reader->irq_lock);
+ cb710_dump_regs(chip, CB710_DUMP_REGS_MMC);
+
+ cb710_mmc_enable_irq(slot, 0, ~0);
+ cb710_set_irq_handler(slot, cb710_mmc_irq_handler);
+
+ err = mmc_add_host(mmc);
+ if (unlikely(err))
+ goto err_free_mmc;
+
+ dev_dbg(cb710_slot_dev(slot), "mmc_hostname is %s\n",
+ mmc_hostname(mmc));
+
+ cb710_mmc_enable_irq(slot, CB710_MMC_IE_CARD_INSERTION_STATUS, 0);
+
+ return 0;
+
+err_free_mmc:
+ dev_dbg(cb710_slot_dev(slot), "mmc_add_host() failed: %d\n", err);
+
+ mmc_free_host(mmc);
+ return err;
+}
+
+static int __devexit cb710_mmc_exit(struct platform_device *pdev)
+{
+ struct cb710_slot *slot = cb710_pdev_to_slot(pdev);
+ struct mmc_host *mmc = cb710_slot_to_mmc(slot);
+ struct cb710_mmc_reader *reader = mmc_priv(mmc);
+
+ cb710_mmc_enable_irq(slot, 0, CB710_MMC_IE_CARD_INSERTION_STATUS);
+
+ mmc_remove_host(mmc);
+
+ /* IRQs should be disabled now, but let's stay on the safe side */
+ cb710_mmc_enable_irq(slot, 0, ~0);
+ cb710_set_irq_handler(slot, NULL);
+
+ /* clear config ports - just in case */
+ cb710_write_port_32(slot, CB710_MMC_CONFIG_PORT, 0);
+ cb710_write_port_16(slot, CB710_MMC_CONFIGB_PORT, 0);
+
+ tasklet_kill(&reader->finish_req_tasklet);
+
+ mmc_free_host(mmc);
+ return 0;
+}
+
+static struct platform_driver cb710_mmc_driver = {
+ .driver.name = "cb710-mmc",
+ .probe = cb710_mmc_init,
+ .remove = __devexit_p(cb710_mmc_exit),
+#ifdef CONFIG_PM
+ .suspend = cb710_mmc_suspend,
+ .resume = cb710_mmc_resume,
+#endif
+};
+
+static int __init cb710_mmc_init_module(void)
+{
+ return platform_driver_register(&cb710_mmc_driver);
+}
+
+static void __exit cb710_mmc_cleanup_module(void)
+{
+ platform_driver_unregister(&cb710_mmc_driver);
+}
+
+module_init(cb710_mmc_init_module);
+module_exit(cb710_mmc_cleanup_module);
+
+MODULE_AUTHOR("Michał Mirosław <mirq-linux@rere.qmqm.pl>");
+MODULE_DESCRIPTION("ENE CB710 memory card reader driver - MMC/SD part");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:cb710-mmc");
diff --git a/drivers/mmc/host/cb710-mmc.h b/drivers/mmc/host/cb710-mmc.h
new file mode 100644
index 00000000000..e845c776bdd
--- /dev/null
+++ b/drivers/mmc/host/cb710-mmc.h
@@ -0,0 +1,104 @@
+/*
+ * cb710/cb710-mmc.h
+ *
+ * Copyright by Michał Mirosław, 2008-2009
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef LINUX_CB710_MMC_H
+#define LINUX_CB710_MMC_H
+
+#include <linux/cb710.h>
+
+/* per-MMC-reader structure */
+struct cb710_mmc_reader {
+ struct tasklet_struct finish_req_tasklet;
+ struct mmc_request *mrq;
+ spinlock_t irq_lock;
+ unsigned char last_power_mode;
+};
+
+/* some device struct walking */
+
+static inline struct mmc_host *cb710_slot_to_mmc(struct cb710_slot *slot)
+{
+ return dev_get_drvdata(&slot->pdev.dev);
+}
+
+static inline struct cb710_slot *cb710_mmc_to_slot(struct mmc_host *mmc)
+{
+ struct platform_device *pdev = container_of(mmc_dev(mmc),
+ struct platform_device, dev);
+ return cb710_pdev_to_slot(pdev);
+}
+
+/* registers (this might be all wrong ;) */
+
+#define CB710_MMC_DATA_PORT 0x00
+
+#define CB710_MMC_CONFIG_PORT 0x04
+#define CB710_MMC_CONFIG0_PORT 0x04
+#define CB710_MMC_CONFIG1_PORT 0x05
+#define CB710_MMC_C1_4BIT_DATA_BUS 0x40
+#define CB710_MMC_CONFIG2_PORT 0x06
+#define CB710_MMC_C2_READ_PIO_SIZE_MASK 0x0F /* N-1 */
+#define CB710_MMC_CONFIG3_PORT 0x07
+
+#define CB710_MMC_CONFIGB_PORT 0x08
+
+#define CB710_MMC_IRQ_ENABLE_PORT 0x0C
+#define CB710_MMC_IE_TEST_MASK 0x00BF
+#define CB710_MMC_IE_CARD_INSERTION_STATUS 0x1000
+#define CB710_MMC_IE_IRQ_ENABLE 0x8000
+#define CB710_MMC_IE_CISTATUS_MASK \
+ (CB710_MMC_IE_CARD_INSERTION_STATUS|CB710_MMC_IE_IRQ_ENABLE)
+
+#define CB710_MMC_STATUS_PORT 0x10
+#define CB710_MMC_STATUS_ERROR_EVENTS 0x60FF
+#define CB710_MMC_STATUS0_PORT 0x10
+#define CB710_MMC_S0_FIFO_UNDERFLOW 0x40
+#define CB710_MMC_STATUS1_PORT 0x11
+#define CB710_MMC_S1_COMMAND_SENT 0x01
+#define CB710_MMC_S1_DATA_TRANSFER_DONE 0x02
+#define CB710_MMC_S1_PIO_TRANSFER_DONE 0x04
+#define CB710_MMC_S1_CARD_CHANGED 0x10
+#define CB710_MMC_S1_RESET 0x20
+#define CB710_MMC_STATUS2_PORT 0x12
+#define CB710_MMC_S2_FIFO_READY 0x01
+#define CB710_MMC_S2_FIFO_EMPTY 0x02
+#define CB710_MMC_S2_BUSY_10 0x10
+#define CB710_MMC_S2_BUSY_20 0x20
+#define CB710_MMC_STATUS3_PORT 0x13
+#define CB710_MMC_S3_CARD_DETECTED 0x02
+#define CB710_MMC_S3_WRITE_PROTECTED 0x04
+
+#define CB710_MMC_CMD_TYPE_PORT 0x14
+#define CB710_MMC_RSP_TYPE_MASK 0x0007
+#define CB710_MMC_RSP_R1 (0)
+#define CB710_MMC_RSP_136 (5)
+#define CB710_MMC_RSP_NO_CRC (2)
+#define CB710_MMC_RSP_PRESENT_MASK 0x0018
+#define CB710_MMC_RSP_NONE (0 << 3)
+#define CB710_MMC_RSP_PRESENT (1 << 3)
+#define CB710_MMC_RSP_PRESENT_X (2 << 3)
+#define CB710_MMC_CMD_TYPE_MASK 0x0060
+#define CB710_MMC_CMD_BC (0 << 5)
+#define CB710_MMC_CMD_BCR (1 << 5)
+#define CB710_MMC_CMD_AC (2 << 5)
+#define CB710_MMC_CMD_ADTC (3 << 5)
+#define CB710_MMC_DATA_READ 0x0080
+#define CB710_MMC_CMD_CODE_MASK 0x3F00
+#define CB710_MMC_CMD_CODE_SHIFT 8
+#define CB710_MMC_IS_APP_CMD 0x4000
+#define CB710_MMC_RSP_BUSY 0x8000
+
+#define CB710_MMC_CMD_PARAM_PORT 0x18
+#define CB710_MMC_TRANSFER_SIZE_PORT 0x1C
+#define CB710_MMC_RESPONSE0_PORT 0x20
+#define CB710_MMC_RESPONSE1_PORT 0x24
+#define CB710_MMC_RESPONSE2_PORT 0x28
+#define CB710_MMC_RESPONSE3_PORT 0x2C
+
+#endif /* LINUX_CB710_MMC_H */
diff --git a/drivers/mmc/host/mmc_spi.c b/drivers/mmc/host/mmc_spi.c
index f48349d18c9..240608cc7ae 100644
--- a/drivers/mmc/host/mmc_spi.c
+++ b/drivers/mmc/host/mmc_spi.c
@@ -97,6 +97,14 @@
*/
#define r1b_timeout (HZ * 3)
+/* One of the critical speed parameters is the amount of data which may
+ * be transfered in one command. If this value is too low, the SD card
+ * controller has to do multiple partial block writes (argggh!). With
+ * today (2008) SD cards there is little speed gain if we transfer more
+ * than 64 KBytes at a time. So use this value until there is any indication
+ * that we should do more here.
+ */
+#define MMC_SPI_BLOCKSATONCE 128
/****************************************************************************/
@@ -327,15 +335,16 @@ checkstatus:
/* Status byte: the entire seven-bit R1 response. */
if (cmd->resp[0] != 0) {
- if ((R1_SPI_PARAMETER | R1_SPI_ADDRESS
- | R1_SPI_ILLEGAL_COMMAND)
+ if ((R1_SPI_PARAMETER | R1_SPI_ADDRESS)
& cmd->resp[0])
- value = -EINVAL;
+ value = -EFAULT; /* Bad address */
+ else if (R1_SPI_ILLEGAL_COMMAND & cmd->resp[0])
+ value = -ENOSYS; /* Function not implemented */
else if (R1_SPI_COM_CRC & cmd->resp[0])
- value = -EILSEQ;
+ value = -EILSEQ; /* Illegal byte sequence */
else if ((R1_SPI_ERASE_SEQ | R1_SPI_ERASE_RESET)
& cmd->resp[0])
- value = -EIO;
+ value = -EIO; /* I/O error */
/* else R1_SPI_IDLE, "it's resetting" */
}
@@ -1366,6 +1375,10 @@ static int mmc_spi_probe(struct spi_device *spi)
mmc->ops = &mmc_spi_ops;
mmc->max_blk_size = MMC_SPI_BLOCKSIZE;
+ mmc->max_hw_segs = MMC_SPI_BLOCKSATONCE;
+ mmc->max_phys_segs = MMC_SPI_BLOCKSATONCE;
+ mmc->max_req_size = MMC_SPI_BLOCKSATONCE * MMC_SPI_BLOCKSIZE;
+ mmc->max_blk_count = MMC_SPI_BLOCKSATONCE;
mmc->caps = MMC_CAP_SPI;
diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c
index a663429b3d5..e1aa8471ab1 100644
--- a/drivers/mmc/host/mmci.c
+++ b/drivers/mmc/host/mmci.c
@@ -490,7 +490,7 @@ static void mmci_check_status(unsigned long data)
mod_timer(&host->timer, jiffies + HZ);
}
-static int __devinit mmci_probe(struct amba_device *dev, void *id)
+static int __devinit mmci_probe(struct amba_device *dev, struct amba_id *id)
{
struct mmc_platform_data *plat = dev->dev.platform_data;
struct mmci_host *host;
@@ -514,6 +514,7 @@ static int __devinit mmci_probe(struct amba_device *dev, void *id)
}
host = mmc_priv(mmc);
+ host->mmc = mmc;
/* Bits 12 thru 19 is the designer */
host->hw_designer = (dev->periphid >> 12) & 0xff;
/* Bits 20 thru 23 is the revison */
@@ -545,8 +546,7 @@ static int __devinit mmci_probe(struct amba_device *dev, void *id)
host->mclk = clk_get_rate(host->clk);
DBG(host, "eventual mclk rate: %u Hz\n", host->mclk);
}
- host->mmc = mmc;
- host->base = ioremap(dev->res.start, SZ_4K);
+ host->base = ioremap(dev->res.start, resource_size(&dev->res));
if (!host->base) {
ret = -ENOMEM;
goto clk_disable;
diff --git a/drivers/mmc/host/mvsdio.c b/drivers/mmc/host/mvsdio.c
index b5c375d94ab..b56d72ff06e 100644
--- a/drivers/mmc/host/mvsdio.c
+++ b/drivers/mmc/host/mvsdio.c
@@ -64,6 +64,31 @@ static int mvsd_setup_data(struct mvsd_host *host, struct mmc_data *data)
unsigned int tmout;
int tmout_index;
+ /*
+ * Hardware weirdness. The FIFO_EMPTY bit of the HW_STATE
+ * register is sometimes not set before a while when some
+ * "unusual" data block sizes are used (such as with the SWITCH
+ * command), even despite the fact that the XFER_DONE interrupt
+ * was raised. And if another data transfer starts before
+ * this bit comes to good sense (which eventually happens by
+ * itself) then the new transfer simply fails with a timeout.
+ */
+ if (!(mvsd_read(MVSD_HW_STATE) & (1 << 13))) {
+ unsigned long t = jiffies + HZ;
+ unsigned int hw_state, count = 0;
+ do {
+ if (time_after(jiffies, t)) {
+ dev_warn(host->dev, "FIFO_EMPTY bit missing\n");
+ break;
+ }
+ hw_state = mvsd_read(MVSD_HW_STATE);
+ count++;
+ } while (!(hw_state & (1 << 13)));
+ dev_dbg(host->dev, "*** wait for FIFO_EMPTY bit "
+ "(hw=0x%04x, count=%d, jiffies=%ld)\n",
+ hw_state, count, jiffies - (t - HZ));
+ }
+
/* If timeout=0 then maximum timeout index is used. */
tmout = DIV_ROUND_UP(data->timeout_ns, host->ns_per_clk);
tmout += data->timeout_clks;
@@ -620,9 +645,18 @@ static void mvsd_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
if (ios->bus_width == MMC_BUS_WIDTH_4)
ctrl_reg |= MVSD_HOST_CTRL_DATA_WIDTH_4_BITS;
+ /*
+ * The HI_SPEED_EN bit is causing trouble with many (but not all)
+ * high speed SD, SDHC and SDIO cards. Not enabling that bit
+ * makes all cards work. So let's just ignore that bit for now
+ * and revisit this issue if problems for not enabling this bit
+ * are ever reported.
+ */
+#if 0
if (ios->timing == MMC_TIMING_MMC_HS ||
ios->timing == MMC_TIMING_SD_HS)
ctrl_reg |= MVSD_HOST_CTRL_HI_SPEED_EN;
+#endif
host->ctrl = ctrl_reg;
mvsd_write(MVSD_HOST_CTRL, ctrl_reg);
@@ -825,24 +859,23 @@ static int __exit mvsd_remove(struct platform_device *pdev)
}
#ifdef CONFIG_PM
-static int mvsd_suspend(struct platform_device *dev, pm_message_t state,
- u32 level)
+static int mvsd_suspend(struct platform_device *dev, pm_message_t state)
{
struct mmc_host *mmc = platform_get_drvdata(dev);
int ret = 0;
- if (mmc && level == SUSPEND_DISABLE)
+ if (mmc)
ret = mmc_suspend_host(mmc, state);
return ret;
}
-static int mvsd_resume(struct platform_device *dev, u32 level)
+static int mvsd_resume(struct platform_device *dev)
{
- struct mmc_host *mmc = platform_dev_get_drvdata(dev);
+ struct mmc_host *mmc = platform_get_drvdata(dev);
int ret = 0;
- if (mmc && level == RESUME_ENABLE)
+ if (mmc)
ret = mmc_resume_host(mmc);
return ret;
@@ -883,3 +916,4 @@ module_param(nodma, int, 0);
MODULE_AUTHOR("Maen Suleiman, Nicolas Pitre");
MODULE_DESCRIPTION("Marvell MMC,SD,SDIO Host Controller driver");
MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:mvsdio");
diff --git a/drivers/mmc/host/mxcmmc.c b/drivers/mmc/host/mxcmmc.c
index b4a615c55f2..bc14bb1b057 100644
--- a/drivers/mmc/host/mxcmmc.c
+++ b/drivers/mmc/host/mxcmmc.c
@@ -140,6 +140,8 @@ struct mxcmci_host {
struct work_struct datawork;
};
+static void mxcmci_set_clk_rate(struct mxcmci_host *host, unsigned int clk_ios);
+
static inline int mxcmci_use_dma(struct mxcmci_host *host)
{
return host->do_dma;
@@ -160,7 +162,7 @@ static void mxcmci_softreset(struct mxcmci_host *host)
writew(0xff, host->base + MMC_REG_RES_TO);
}
-static void mxcmci_setup_data(struct mxcmci_host *host, struct mmc_data *data)
+static int mxcmci_setup_data(struct mxcmci_host *host, struct mmc_data *data)
{
unsigned int nob = data->blocks;
unsigned int blksz = data->blksz;
@@ -168,6 +170,7 @@ static void mxcmci_setup_data(struct mxcmci_host *host, struct mmc_data *data)
#ifdef HAS_DMA
struct scatterlist *sg;
int i;
+ int ret;
#endif
if (data->flags & MMC_DATA_STREAM)
nob = 0xffff;
@@ -183,7 +186,7 @@ static void mxcmci_setup_data(struct mxcmci_host *host, struct mmc_data *data)
for_each_sg(data->sg, sg, data->sg_len, i) {
if (sg->offset & 3 || sg->length & 3) {
host->do_dma = 0;
- return;
+ return 0;
}
}
@@ -192,23 +195,30 @@ static void mxcmci_setup_data(struct mxcmci_host *host, struct mmc_data *data)
host->dma_nents = dma_map_sg(mmc_dev(host->mmc), data->sg,
data->sg_len, host->dma_dir);
- imx_dma_setup_sg(host->dma, data->sg, host->dma_nents, datasize,
- host->res->start + MMC_REG_BUFFER_ACCESS,
- DMA_MODE_READ);
+ ret = imx_dma_setup_sg(host->dma, data->sg, host->dma_nents,
+ datasize,
+ host->res->start + MMC_REG_BUFFER_ACCESS,
+ DMA_MODE_READ);
} else {
host->dma_dir = DMA_TO_DEVICE;
host->dma_nents = dma_map_sg(mmc_dev(host->mmc), data->sg,
data->sg_len, host->dma_dir);
- imx_dma_setup_sg(host->dma, data->sg, host->dma_nents, datasize,
- host->res->start + MMC_REG_BUFFER_ACCESS,
- DMA_MODE_WRITE);
+ ret = imx_dma_setup_sg(host->dma, data->sg, host->dma_nents,
+ datasize,
+ host->res->start + MMC_REG_BUFFER_ACCESS,
+ DMA_MODE_WRITE);
}
+ if (ret) {
+ dev_err(mmc_dev(host->mmc), "failed to setup DMA : %d\n", ret);
+ return ret;
+ }
wmb();
imx_dma_enable(host->dma);
#endif /* HAS_DMA */
+ return 0;
}
static int mxcmci_start_cmd(struct mxcmci_host *host, struct mmc_command *cmd,
@@ -345,8 +355,11 @@ static int mxcmci_poll_status(struct mxcmci_host *host, u32 mask)
stat = readl(host->base + MMC_REG_STATUS);
if (stat & STATUS_ERR_MASK)
return stat;
- if (time_after(jiffies, timeout))
+ if (time_after(jiffies, timeout)) {
+ mxcmci_softreset(host);
+ mxcmci_set_clk_rate(host, host->clock);
return STATUS_TIME_OUT_READ;
+ }
if (stat & mask)
return 0;
cpu_relax();
@@ -531,6 +544,7 @@ static void mxcmci_request(struct mmc_host *mmc, struct mmc_request *req)
{
struct mxcmci_host *host = mmc_priv(mmc);
unsigned int cmdat = host->cmdat;
+ int error;
WARN_ON(host->req != NULL);
@@ -540,7 +554,12 @@ static void mxcmci_request(struct mmc_host *mmc, struct mmc_request *req)
host->do_dma = 1;
#endif
if (req->data) {
- mxcmci_setup_data(host, req->data);
+ error = mxcmci_setup_data(host, req->data);
+ if (error) {
+ req->cmd->error = error;
+ goto out;
+ }
+
cmdat |= CMD_DAT_CONT_DATA_ENABLE;
@@ -548,7 +567,9 @@ static void mxcmci_request(struct mmc_host *mmc, struct mmc_request *req)
cmdat |= CMD_DAT_CONT_WRITE;
}
- if (mxcmci_start_cmd(host, req->cmd, cmdat))
+ error = mxcmci_start_cmd(host, req->cmd, cmdat);
+out:
+ if (error)
mxcmci_finish_request(host, req);
}
@@ -724,7 +745,7 @@ static int mxcmci_probe(struct platform_device *pdev)
goto out_clk_put;
}
- mmc->f_min = clk_get_rate(host->clk) >> 7;
+ mmc->f_min = clk_get_rate(host->clk) >> 16;
mmc->f_max = clk_get_rate(host->clk) >> 1;
/* recommended in data sheet */
diff --git a/drivers/mmc/host/omap.c b/drivers/mmc/host/omap.c
index 5570849188c..e7a331de573 100644
--- a/drivers/mmc/host/omap.c
+++ b/drivers/mmc/host/omap.c
@@ -157,8 +157,6 @@ struct mmc_omap_host {
struct timer_list dma_timer;
unsigned dma_len;
- short power_pin;
-
struct mmc_omap_slot *slots[OMAP_MMC_MAX_SLOTS];
struct mmc_omap_slot *current_slot;
spinlock_t slot_lock;
@@ -824,7 +822,7 @@ static irqreturn_t mmc_omap_irq(int irq, void *dev_id)
del_timer(&host->cmd_abort_timer);
host->abort = 1;
OMAP_MMC_WRITE(host, IE, 0);
- disable_irq(host->irq);
+ disable_irq_nosync(host->irq);
schedule_work(&host->cmd_abort_work);
return IRQ_HANDLED;
}
@@ -1595,7 +1593,6 @@ static int mmc_omap_resume(struct platform_device *pdev)
#endif
static struct platform_driver mmc_omap_driver = {
- .probe = mmc_omap_probe,
.remove = mmc_omap_remove,
.suspend = mmc_omap_suspend,
.resume = mmc_omap_resume,
@@ -1607,7 +1604,7 @@ static struct platform_driver mmc_omap_driver = {
static int __init mmc_omap_init(void)
{
- return platform_driver_register(&mmc_omap_driver);
+ return platform_driver_probe(&mmc_omap_driver, mmc_omap_probe);
}
static void __exit mmc_omap_exit(void)
diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
index e62a22a7f00..1cf9cfb3b64 100644
--- a/drivers/mmc/host/omap_hsmmc.c
+++ b/drivers/mmc/host/omap_hsmmc.c
@@ -680,7 +680,7 @@ static void mmc_omap_dma_cb(int lch, u16 ch_status, void *data)
host->dma_ch = -1;
/*
* DMA Callback: run in interrupt context.
- * mutex_unlock will through a kernel warning if used.
+ * mutex_unlock will throw a kernel warning if used.
*/
up(&host->sem);
}
@@ -1073,7 +1073,6 @@ static int __init omap_mmc_probe(struct platform_device *pdev)
mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count;
mmc->max_seg_size = mmc->max_req_size;
- mmc->ocr_avail = mmc_slot(host).ocr_mask;
mmc->caps |= MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED;
if (pdata->slots[host->slot_id].wires >= 8)
@@ -1110,13 +1109,14 @@ static int __init omap_mmc_probe(struct platform_device *pdev)
goto err_irq;
}
+ /* initialize power supplies, gpios, etc */
if (pdata->init != NULL) {
if (pdata->init(&pdev->dev) != 0) {
- dev_dbg(mmc_dev(host->mmc),
- "Unable to configure MMC IRQs\n");
+ dev_dbg(mmc_dev(host->mmc), "late init error\n");
goto err_irq_cd_init;
}
}
+ mmc->ocr_avail = mmc_slot(host).ocr_mask;
/* Request IRQ for card detect */
if ((mmc_slot(host).card_detect_irq)) {
diff --git a/drivers/mmc/host/pxamci.c b/drivers/mmc/host/pxamci.c
index 430095725f9..d7d7109ef47 100644
--- a/drivers/mmc/host/pxamci.c
+++ b/drivers/mmc/host/pxamci.c
@@ -27,6 +27,7 @@
#include <linux/err.h>
#include <linux/mmc/host.h>
#include <linux/io.h>
+#include <linux/regulator/consumer.h>
#include <asm/sizes.h>
@@ -67,8 +68,42 @@ struct pxamci_host {
unsigned int dma_dir;
unsigned int dma_drcmrrx;
unsigned int dma_drcmrtx;
+
+ struct regulator *vcc;
};
+static inline void pxamci_init_ocr(struct pxamci_host *host)
+{
+#ifdef CONFIG_REGULATOR
+ host->vcc = regulator_get(mmc_dev(host->mmc), "vmmc");
+
+ if (IS_ERR(host->vcc))
+ host->vcc = NULL;
+ else {
+ host->mmc->ocr_avail = mmc_regulator_get_ocrmask(host->vcc);
+ if (host->pdata && host->pdata->ocr_mask)
+ dev_warn(mmc_dev(host->mmc),
+ "ocr_mask/setpower will not be used\n");
+ }
+#endif
+ if (host->vcc == NULL) {
+ /* fall-back to platform data */
+ host->mmc->ocr_avail = host->pdata ?
+ host->pdata->ocr_mask :
+ MMC_VDD_32_33 | MMC_VDD_33_34;
+ }
+}
+
+static inline void pxamci_set_power(struct pxamci_host *host, unsigned int vdd)
+{
+#ifdef CONFIG_REGULATOR
+ if (host->vcc)
+ mmc_regulator_set_ocr(host->vcc, vdd);
+#endif
+ if (!host->vcc && host->pdata && host->pdata->setpower)
+ host->pdata->setpower(mmc_dev(host->mmc), vdd);
+}
+
static void pxamci_stop_clock(struct pxamci_host *host)
{
if (readl(host->base + MMC_STAT) & STAT_CLK_EN) {
@@ -438,8 +473,7 @@ static void pxamci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
if (host->power_mode != ios->power_mode) {
host->power_mode = ios->power_mode;
- if (host->pdata && host->pdata->setpower)
- host->pdata->setpower(mmc_dev(mmc), ios->vdd);
+ pxamci_set_power(host, ios->vdd);
if (ios->power_mode == MMC_POWER_ON)
host->cmdat |= CMDAT_INIT;
@@ -562,9 +596,8 @@ static int pxamci_probe(struct platform_device *pdev)
mmc->f_max = (cpu_is_pxa300() || cpu_is_pxa310()) ? 26000000
: host->clkrate;
- mmc->ocr_avail = host->pdata ?
- host->pdata->ocr_mask :
- MMC_VDD_32_33|MMC_VDD_33_34;
+ pxamci_init_ocr(host);
+
mmc->caps = 0;
host->cmdat = 0;
if (!cpu_is_pxa25x()) {
@@ -661,6 +694,9 @@ static int pxamci_remove(struct platform_device *pdev)
if (mmc) {
struct pxamci_host *host = mmc_priv(mmc);
+ if (host->vcc)
+ regulator_put(host->vcc);
+
if (host->pdata && host->pdata->exit)
host->pdata->exit(&pdev->dev, mmc);
diff --git a/drivers/mmc/host/s3cmci.c b/drivers/mmc/host/s3cmci.c
index 2db166b7096..4eb4f37544a 100644
--- a/drivers/mmc/host/s3cmci.c
+++ b/drivers/mmc/host/s3cmci.c
@@ -17,6 +17,7 @@
#include <linux/mmc/host.h>
#include <linux/platform_device.h>
#include <linux/cpufreq.h>
+#include <linux/gpio.h>
#include <linux/irq.h>
#include <linux/io.h>
@@ -789,7 +790,7 @@ static void s3cmci_dma_setup(struct s3cmci_host *host,
last_source = source;
- s3c2410_dma_devconfig(host->dma, source, 3,
+ s3c2410_dma_devconfig(host->dma, source,
host->mem->start + host->sdidata);
if (!setup_ok) {
@@ -1121,7 +1122,7 @@ static void s3cmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
case MMC_POWER_OFF:
default:
s3c2410_gpio_setpin(S3C2410_GPE5, 0);
- s3c2410_gpio_cfgpin(S3C2410_GPE5, S3C2410_GPE5_OUTP);
+ s3c2410_gpio_cfgpin(S3C2410_GPE5, S3C2410_GPIO_OUTPUT);
if (host->is2440)
mci_con |= S3C2440_SDICON_SDRESET;
diff --git a/drivers/mmc/host/sdhci-of.c b/drivers/mmc/host/sdhci-of.c
index 3ff4ac3abe8..128c614d11a 100644
--- a/drivers/mmc/host/sdhci-of.c
+++ b/drivers/mmc/host/sdhci-of.c
@@ -55,7 +55,13 @@ static u32 esdhc_readl(struct sdhci_host *host, int reg)
static u16 esdhc_readw(struct sdhci_host *host, int reg)
{
- return in_be16(host->ioaddr + (reg ^ 0x2));
+ u16 ret;
+
+ if (unlikely(reg == SDHCI_HOST_VERSION))
+ ret = in_be16(host->ioaddr + reg);
+ else
+ ret = in_be16(host->ioaddr + (reg ^ 0x2));
+ return ret;
}
static u8 esdhc_readb(struct sdhci_host *host, int reg)
@@ -277,6 +283,7 @@ static int __devexit sdhci_of_remove(struct of_device *ofdev)
static const struct of_device_id sdhci_of_match[] = {
{ .compatible = "fsl,mpc8379-esdhc", .data = &sdhci_esdhc, },
{ .compatible = "fsl,mpc8536-esdhc", .data = &sdhci_esdhc, },
+ { .compatible = "fsl,esdhc", .data = &sdhci_esdhc, },
{ .compatible = "generic-sdhci", },
{},
};
diff --git a/drivers/mmc/host/sdhci-pci.c b/drivers/mmc/host/sdhci-pci.c
index cd37962ec44..65be27995d5 100644
--- a/drivers/mmc/host/sdhci-pci.c
+++ b/drivers/mmc/host/sdhci-pci.c
@@ -522,8 +522,8 @@ static struct sdhci_pci_slot * __devinit sdhci_pci_probe_slot(
host = sdhci_alloc_host(&pdev->dev, sizeof(struct sdhci_pci_slot));
if (IS_ERR(host)) {
- ret = PTR_ERR(host);
- goto unmap;
+ dev_err(&pdev->dev, "cannot allocate host\n");
+ return ERR_PTR(PTR_ERR(host));
}
slot = sdhci_priv(host);
@@ -541,7 +541,7 @@ static struct sdhci_pci_slot * __devinit sdhci_pci_probe_slot(
ret = pci_request_region(pdev, bar, mmc_hostname(host->mmc));
if (ret) {
dev_err(&pdev->dev, "cannot request region\n");
- return ERR_PTR(ret);
+ goto free;
}
addr = pci_resource_start(pdev, bar);
@@ -572,6 +572,8 @@ unmap:
release:
pci_release_region(pdev, bar);
+
+free:
sdhci_free_host(host);
return ERR_PTR(ret);
diff --git a/drivers/mmc/host/sdhci-pltfm.c b/drivers/mmc/host/sdhci-pltfm.c
new file mode 100644
index 00000000000..297f40ae6ad
--- /dev/null
+++ b/drivers/mmc/host/sdhci-pltfm.c
@@ -0,0 +1,168 @@
+/*
+ * sdhci-pltfm.c Support for SDHCI platform devices
+ * Copyright (c) 2009 Intel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+/* Supports:
+ * SDHCI platform devices
+ *
+ * Inspired by sdhci-pci.c, by Pierre Ossman
+ */
+
+#include <linux/delay.h>
+#include <linux/highmem.h>
+#include <linux/platform_device.h>
+
+#include <linux/mmc/host.h>
+
+#include <linux/io.h>
+
+#include "sdhci.h"
+
+/*****************************************************************************\
+ * *
+ * SDHCI core callbacks *
+ * *
+\*****************************************************************************/
+
+static struct sdhci_ops sdhci_pltfm_ops = {
+};
+
+/*****************************************************************************\
+ * *
+ * Device probing/removal *
+ * *
+\*****************************************************************************/
+
+static int __devinit sdhci_pltfm_probe(struct platform_device *pdev)
+{
+ struct sdhci_host *host;
+ struct resource *iomem;
+ int ret;
+
+ BUG_ON(pdev == NULL);
+
+ iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!iomem) {
+ ret = -ENOMEM;
+ goto err;
+ }
+
+ if (resource_size(iomem) != 0x100)
+ dev_err(&pdev->dev, "Invalid iomem size. You may "
+ "experience problems.\n");
+
+ if (pdev->dev.parent)
+ host = sdhci_alloc_host(pdev->dev.parent, 0);
+ else
+ host = sdhci_alloc_host(&pdev->dev, 0);
+
+ if (IS_ERR(host)) {
+ ret = PTR_ERR(host);
+ goto err;
+ }
+
+ host->hw_name = "platform";
+ host->ops = &sdhci_pltfm_ops;
+ host->irq = platform_get_irq(pdev, 0);
+
+ if (!request_mem_region(iomem->start, resource_size(iomem),
+ mmc_hostname(host->mmc))) {
+ dev_err(&pdev->dev, "cannot request region\n");
+ ret = -EBUSY;
+ goto err_request;
+ }
+
+ host->ioaddr = ioremap(iomem->start, resource_size(iomem));
+ if (!host->ioaddr) {
+ dev_err(&pdev->dev, "failed to remap registers\n");
+ ret = -ENOMEM;
+ goto err_remap;
+ }
+
+ ret = sdhci_add_host(host);
+ if (ret)
+ goto err_add_host;
+
+ platform_set_drvdata(pdev, host);
+
+ return 0;
+
+err_add_host:
+ iounmap(host->ioaddr);
+err_remap:
+ release_mem_region(iomem->start, resource_size(iomem));
+err_request:
+ sdhci_free_host(host);
+err:
+ printk(KERN_ERR"Probing of sdhci-pltfm failed: %d\n", ret);
+ return ret;
+}
+
+static int __devexit sdhci_pltfm_remove(struct platform_device *pdev)
+{
+ struct sdhci_host *host = platform_get_drvdata(pdev);
+ struct resource *iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ int dead;
+ u32 scratch;
+
+ dead = 0;
+ scratch = readl(host->ioaddr + SDHCI_INT_STATUS);
+ if (scratch == (u32)-1)
+ dead = 1;
+
+ sdhci_remove_host(host, dead);
+ iounmap(host->ioaddr);
+ release_mem_region(iomem->start, resource_size(iomem));
+ sdhci_free_host(host);
+ platform_set_drvdata(pdev, NULL);
+
+ return 0;
+}
+
+static struct platform_driver sdhci_pltfm_driver = {
+ .driver = {
+ .name = "sdhci",
+ .owner = THIS_MODULE,
+ },
+ .probe = sdhci_pltfm_probe,
+ .remove = __devexit_p(sdhci_pltfm_remove),
+};
+
+/*****************************************************************************\
+ * *
+ * Driver init/exit *
+ * *
+\*****************************************************************************/
+
+static int __init sdhci_drv_init(void)
+{
+ return platform_driver_register(&sdhci_pltfm_driver);
+}
+
+static void __exit sdhci_drv_exit(void)
+{
+ platform_driver_unregister(&sdhci_pltfm_driver);
+}
+
+module_init(sdhci_drv_init);
+module_exit(sdhci_drv_exit);
+
+MODULE_DESCRIPTION("Secure Digital Host Controller Interface platform driver");
+MODULE_AUTHOR("Mocean Laboratories <info@mocean-labs.com>");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:sdhci");
+
diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
index 9234be2226e..35789c6edc1 100644
--- a/drivers/mmc/host/sdhci.c
+++ b/drivers/mmc/host/sdhci.c
@@ -78,6 +78,11 @@ static void sdhci_dumpregs(struct sdhci_host *host)
sdhci_readl(host, SDHCI_CAPABILITIES),
sdhci_readl(host, SDHCI_MAX_CURRENT));
+ if (host->flags & SDHCI_USE_ADMA)
+ printk(KERN_DEBUG DRIVER_NAME ": ADMA Err: 0x%08x | ADMA Ptr: 0x%08x\n",
+ readl(host->ioaddr + SDHCI_ADMA_ERROR),
+ readl(host->ioaddr + SDHCI_ADMA_ADDRESS));
+
printk(KERN_DEBUG DRIVER_NAME ": ===========================================\n");
}
@@ -1005,12 +1010,34 @@ static void sdhci_set_power(struct sdhci_host *host, unsigned short power)
{
u8 pwr;
- if (host->power == power)
+ if (power == (unsigned short)-1)
+ pwr = 0;
+ else {
+ switch (1 << power) {
+ case MMC_VDD_165_195:
+ pwr = SDHCI_POWER_180;
+ break;
+ case MMC_VDD_29_30:
+ case MMC_VDD_30_31:
+ pwr = SDHCI_POWER_300;
+ break;
+ case MMC_VDD_32_33:
+ case MMC_VDD_33_34:
+ pwr = SDHCI_POWER_330;
+ break;
+ default:
+ BUG();
+ }
+ }
+
+ if (host->pwr == pwr)
return;
- if (power == (unsigned short)-1) {
+ host->pwr = pwr;
+
+ if (pwr == 0) {
sdhci_writeb(host, 0, SDHCI_POWER_CONTROL);
- goto out;
+ return;
}
/*
@@ -1020,35 +1047,16 @@ static void sdhci_set_power(struct sdhci_host *host, unsigned short power)
if (!(host->quirks & SDHCI_QUIRK_SINGLE_POWER_WRITE))
sdhci_writeb(host, 0, SDHCI_POWER_CONTROL);
- pwr = SDHCI_POWER_ON;
-
- switch (1 << power) {
- case MMC_VDD_165_195:
- pwr |= SDHCI_POWER_180;
- break;
- case MMC_VDD_29_30:
- case MMC_VDD_30_31:
- pwr |= SDHCI_POWER_300;
- break;
- case MMC_VDD_32_33:
- case MMC_VDD_33_34:
- pwr |= SDHCI_POWER_330;
- break;
- default:
- BUG();
- }
-
/*
* At least the Marvell CaFe chip gets confused if we set the voltage
* and set turn on power at the same time, so set the voltage first.
*/
if ((host->quirks & SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER))
- sdhci_writeb(host, pwr & ~SDHCI_POWER_ON, SDHCI_POWER_CONTROL);
+ sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
- sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
+ pwr |= SDHCI_POWER_ON;
-out:
- host->power = power;
+ sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
}
/*****************************************************************************\
diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h
index f20a834f430..2de08349c3c 100644
--- a/drivers/mmc/host/sdhci.h
+++ b/drivers/mmc/host/sdhci.h
@@ -125,7 +125,7 @@
#define SDHCI_INT_DATA_MASK (SDHCI_INT_DATA_END | SDHCI_INT_DMA_END | \
SDHCI_INT_DATA_AVAIL | SDHCI_INT_SPACE_AVAIL | \
SDHCI_INT_DATA_TIMEOUT | SDHCI_INT_DATA_CRC | \
- SDHCI_INT_DATA_END_BIT)
+ SDHCI_INT_DATA_END_BIT | SDHCI_ADMA_ERROR)
#define SDHCI_INT_ALL_MASK ((unsigned int)-1)
#define SDHCI_ACMD12_ERR 0x3C
@@ -255,7 +255,7 @@ struct sdhci_host {
unsigned int timeout_clk; /* Timeout freq (KHz) */
unsigned int clock; /* Current clock (MHz) */
- unsigned short power; /* Current voltage */
+ u8 pwr; /* Current voltage */
struct mmc_request *mrq; /* Current request */
struct mmc_command *cmd; /* Current command */
diff --git a/drivers/mmc/host/tmio_mmc.c b/drivers/mmc/host/tmio_mmc.c
index 63fbd5b7d31..91991b460c4 100644
--- a/drivers/mmc/host/tmio_mmc.c
+++ b/drivers/mmc/host/tmio_mmc.c
@@ -10,7 +10,7 @@
*
* Driver for the MMC / SD / SDIO cell found in:
*
- * TC6393XB TC6391XB TC6387XB T7L66XB
+ * TC6393XB TC6391XB TC6387XB T7L66XB ASIC3
*
* This driver draws mainly on scattered spec sheets, Reverse engineering
* of the toshiba e800 SD driver and some parts of the 2.4 ASIC3 driver (4 bit
@@ -35,69 +35,47 @@
#include "tmio_mmc.h"
-/*
- * Fixme - documentation conflicts on what the clock values are for the
- * various dividers.
- * One document I have says that its a divisor of a 24MHz clock, another 33.
- * This probably depends on HCLK for a given platform, so we may need to
- * require HCLK be passed to us from the MFD core.
- *
- */
-
static void tmio_mmc_set_clock(struct tmio_mmc_host *host, int new_clock)
{
- void __iomem *cnf = host->cnf;
- void __iomem *ctl = host->ctl;
u32 clk = 0, clock;
if (new_clock) {
- for (clock = 46875, clk = 0x100; new_clock >= (clock<<1); ) {
+ for (clock = host->mmc->f_min, clk = 0x80000080;
+ new_clock >= (clock<<1); clk >>= 1)
clock <<= 1;
- clk >>= 1;
- }
- if (clk & 0x1)
- clk = 0x20000;
-
- clk >>= 2;
- tmio_iowrite8((clk & 0x8000) ? 0 : 1, cnf + CNF_SD_CLK_MODE);
clk |= 0x100;
}
- tmio_iowrite16(clk, ctl + CTL_SD_CARD_CLK_CTL);
+ sd_config_write8(host, CNF_SD_CLK_MODE, clk >> 22);
+ sd_ctrl_write16(host, CTL_SD_CARD_CLK_CTL, clk & 0x1ff);
}
static void tmio_mmc_clk_stop(struct tmio_mmc_host *host)
{
- void __iomem *ctl = host->ctl;
-
- tmio_iowrite16(0x0000, ctl + CTL_CLK_AND_WAIT_CTL);
+ sd_ctrl_write16(host, CTL_CLK_AND_WAIT_CTL, 0x0000);
msleep(10);
- tmio_iowrite16(tmio_ioread16(ctl + CTL_SD_CARD_CLK_CTL) & ~0x0100,
- ctl + CTL_SD_CARD_CLK_CTL);
+ sd_ctrl_write16(host, CTL_SD_CARD_CLK_CTL, ~0x0100 &
+ sd_ctrl_read16(host, CTL_SD_CARD_CLK_CTL));
msleep(10);
}
static void tmio_mmc_clk_start(struct tmio_mmc_host *host)
{
- void __iomem *ctl = host->ctl;
-
- tmio_iowrite16(tmio_ioread16(ctl + CTL_SD_CARD_CLK_CTL) | 0x0100,
- ctl + CTL_SD_CARD_CLK_CTL);
+ sd_ctrl_write16(host, CTL_SD_CARD_CLK_CTL, 0x0100 |
+ sd_ctrl_read16(host, CTL_SD_CARD_CLK_CTL));
msleep(10);
- tmio_iowrite16(0x0100, ctl + CTL_CLK_AND_WAIT_CTL);
+ sd_ctrl_write16(host, CTL_CLK_AND_WAIT_CTL, 0x0100);
msleep(10);
}
static void reset(struct tmio_mmc_host *host)
{
- void __iomem *ctl = host->ctl;
-
/* FIXME - should we set stop clock reg here */
- tmio_iowrite16(0x0000, ctl + CTL_RESET_SD);
- tmio_iowrite16(0x0000, ctl + CTL_RESET_SDIO);
+ sd_ctrl_write16(host, CTL_RESET_SD, 0x0000);
+ sd_ctrl_write16(host, CTL_RESET_SDIO, 0x0000);
msleep(10);
- tmio_iowrite16(0x0001, ctl + CTL_RESET_SD);
- tmio_iowrite16(0x0001, ctl + CTL_RESET_SDIO);
+ sd_ctrl_write16(host, CTL_RESET_SD, 0x0001);
+ sd_ctrl_write16(host, CTL_RESET_SDIO, 0x0001);
msleep(10);
}
@@ -129,13 +107,12 @@ tmio_mmc_finish_request(struct tmio_mmc_host *host)
static int
tmio_mmc_start_command(struct tmio_mmc_host *host, struct mmc_command *cmd)
{
- void __iomem *ctl = host->ctl;
struct mmc_data *data = host->data;
int c = cmd->opcode;
/* Command 12 is handled by hardware */
if (cmd->opcode == 12 && !cmd->arg) {
- tmio_iowrite16(0x001, ctl + CTL_STOP_INTERNAL_ACTION);
+ sd_ctrl_write16(host, CTL_STOP_INTERNAL_ACTION, 0x001);
return 0;
}
@@ -160,18 +137,18 @@ tmio_mmc_start_command(struct tmio_mmc_host *host, struct mmc_command *cmd)
if (data) {
c |= DATA_PRESENT;
if (data->blocks > 1) {
- tmio_iowrite16(0x100, ctl + CTL_STOP_INTERNAL_ACTION);
+ sd_ctrl_write16(host, CTL_STOP_INTERNAL_ACTION, 0x100);
c |= TRANSFER_MULTI;
}
if (data->flags & MMC_DATA_READ)
c |= TRANSFER_READ;
}
- enable_mmc_irqs(ctl, TMIO_MASK_CMD);
+ enable_mmc_irqs(host, TMIO_MASK_CMD);
/* Fire off the command */
- tmio_iowrite32(cmd->arg, ctl + CTL_ARG_REG);
- tmio_iowrite16(c, ctl + CTL_SD_CMD);
+ sd_ctrl_write32(host, CTL_ARG_REG, cmd->arg);
+ sd_ctrl_write16(host, CTL_SD_CMD, c);
return 0;
}
@@ -183,7 +160,6 @@ tmio_mmc_start_command(struct tmio_mmc_host *host, struct mmc_command *cmd)
*/
static inline void tmio_mmc_pio_irq(struct tmio_mmc_host *host)
{
- void __iomem *ctl = host->ctl;
struct mmc_data *data = host->data;
unsigned short *buf;
unsigned int count;
@@ -206,9 +182,9 @@ static inline void tmio_mmc_pio_irq(struct tmio_mmc_host *host)
/* Transfer the data */
if (data->flags & MMC_DATA_READ)
- tmio_ioread16_rep(ctl + CTL_SD_DATA_PORT, buf, count >> 1);
+ sd_ctrl_read16_rep(host, CTL_SD_DATA_PORT, buf, count >> 1);
else
- tmio_iowrite16_rep(ctl + CTL_SD_DATA_PORT, buf, count >> 1);
+ sd_ctrl_write16_rep(host, CTL_SD_DATA_PORT, buf, count >> 1);
host->sg_off += count;
@@ -222,7 +198,6 @@ static inline void tmio_mmc_pio_irq(struct tmio_mmc_host *host)
static inline void tmio_mmc_data_irq(struct tmio_mmc_host *host)
{
- void __iomem *ctl = host->ctl;
struct mmc_data *data = host->data;
struct mmc_command *stop;
@@ -251,13 +226,13 @@ static inline void tmio_mmc_data_irq(struct tmio_mmc_host *host)
*/
if (data->flags & MMC_DATA_READ)
- disable_mmc_irqs(ctl, TMIO_MASK_READOP);
+ disable_mmc_irqs(host, TMIO_MASK_READOP);
else
- disable_mmc_irqs(ctl, TMIO_MASK_WRITEOP);
+ disable_mmc_irqs(host, TMIO_MASK_WRITEOP);
if (stop) {
if (stop->opcode == 12 && !stop->arg)
- tmio_iowrite16(0x000, ctl + CTL_STOP_INTERNAL_ACTION);
+ sd_ctrl_write16(host, CTL_STOP_INTERNAL_ACTION, 0x000);
else
BUG();
}
@@ -268,9 +243,8 @@ static inline void tmio_mmc_data_irq(struct tmio_mmc_host *host)
static inline void tmio_mmc_cmd_irq(struct tmio_mmc_host *host,
unsigned int stat)
{
- void __iomem *ctl = host->ctl, *addr;
struct mmc_command *cmd = host->cmd;
- int i;
+ int i, addr;
if (!host->cmd) {
pr_debug("Spurious CMD irq\n");
@@ -284,8 +258,8 @@ static inline void tmio_mmc_cmd_irq(struct tmio_mmc_host *host,
* modify the order of the response for short response command types.
*/
- for (i = 3, addr = ctl + CTL_RESPONSE ; i >= 0 ; i--, addr += 4)
- cmd->resp[i] = tmio_ioread32(addr);
+ for (i = 3, addr = CTL_RESPONSE ; i >= 0 ; i--, addr += 4)
+ cmd->resp[i] = sd_ctrl_read32(host, addr);
if (cmd->flags & MMC_RSP_136) {
cmd->resp[0] = (cmd->resp[0] << 8) | (cmd->resp[1] >> 24);
@@ -307,9 +281,9 @@ static inline void tmio_mmc_cmd_irq(struct tmio_mmc_host *host,
*/
if (host->data && !cmd->error) {
if (host->data->flags & MMC_DATA_READ)
- enable_mmc_irqs(ctl, TMIO_MASK_READOP);
+ enable_mmc_irqs(host, TMIO_MASK_READOP);
else
- enable_mmc_irqs(ctl, TMIO_MASK_WRITEOP);
+ enable_mmc_irqs(host, TMIO_MASK_WRITEOP);
} else {
tmio_mmc_finish_request(host);
}
@@ -321,20 +295,19 @@ static inline void tmio_mmc_cmd_irq(struct tmio_mmc_host *host,
static irqreturn_t tmio_mmc_irq(int irq, void *devid)
{
struct tmio_mmc_host *host = devid;
- void __iomem *ctl = host->ctl;
unsigned int ireg, irq_mask, status;
pr_debug("MMC IRQ begin\n");
- status = tmio_ioread32(ctl + CTL_STATUS);
- irq_mask = tmio_ioread32(ctl + CTL_IRQ_MASK);
+ status = sd_ctrl_read32(host, CTL_STATUS);
+ irq_mask = sd_ctrl_read32(host, CTL_IRQ_MASK);
ireg = status & TMIO_MASK_IRQ & ~irq_mask;
pr_debug_status(status);
pr_debug_status(ireg);
if (!ireg) {
- disable_mmc_irqs(ctl, status & ~irq_mask);
+ disable_mmc_irqs(host, status & ~irq_mask);
pr_debug("tmio_mmc: Spurious irq, disabling! "
"0x%08x 0x%08x 0x%08x\n", status, irq_mask, ireg);
@@ -346,7 +319,7 @@ static irqreturn_t tmio_mmc_irq(int irq, void *devid)
while (ireg) {
/* Card insert / remove attempts */
if (ireg & (TMIO_STAT_CARD_INSERT | TMIO_STAT_CARD_REMOVE)) {
- ack_mmc_irqs(ctl, TMIO_STAT_CARD_INSERT |
+ ack_mmc_irqs(host, TMIO_STAT_CARD_INSERT |
TMIO_STAT_CARD_REMOVE);
mmc_detect_change(host->mmc, 0);
}
@@ -358,25 +331,25 @@ static irqreturn_t tmio_mmc_irq(int irq, void *devid)
/* Command completion */
if (ireg & TMIO_MASK_CMD) {
- ack_mmc_irqs(ctl, TMIO_MASK_CMD);
+ ack_mmc_irqs(host, TMIO_MASK_CMD);
tmio_mmc_cmd_irq(host, status);
}
/* Data transfer */
if (ireg & (TMIO_STAT_RXRDY | TMIO_STAT_TXRQ)) {
- ack_mmc_irqs(ctl, TMIO_STAT_RXRDY | TMIO_STAT_TXRQ);
+ ack_mmc_irqs(host, TMIO_STAT_RXRDY | TMIO_STAT_TXRQ);
tmio_mmc_pio_irq(host);
}
/* Data transfer completion */
if (ireg & TMIO_STAT_DATAEND) {
- ack_mmc_irqs(ctl, TMIO_STAT_DATAEND);
+ ack_mmc_irqs(host, TMIO_STAT_DATAEND);
tmio_mmc_data_irq(host);
}
/* Check status - keep going until we've handled it all */
- status = tmio_ioread32(ctl + CTL_STATUS);
- irq_mask = tmio_ioread32(ctl + CTL_IRQ_MASK);
+ status = sd_ctrl_read32(host, CTL_STATUS);
+ irq_mask = sd_ctrl_read32(host, CTL_IRQ_MASK);
ireg = status & TMIO_MASK_IRQ & ~irq_mask;
pr_debug("Status at end of loop: %08x\n", status);
@@ -391,8 +364,6 @@ out:
static int tmio_mmc_start_data(struct tmio_mmc_host *host,
struct mmc_data *data)
{
- void __iomem *ctl = host->ctl;
-
pr_debug("setup data transfer: blocksize %08x nr_blocks %d\n",
data->blksz, data->blocks);
@@ -407,8 +378,8 @@ static int tmio_mmc_start_data(struct tmio_mmc_host *host,
host->data = data;
/* Set transfer length / blocksize */
- tmio_iowrite16(data->blksz, ctl + CTL_SD_XFER_LEN);
- tmio_iowrite16(data->blocks, ctl + CTL_XFER_BLK_COUNT);
+ sd_ctrl_write16(host, CTL_SD_XFER_LEN, data->blksz);
+ sd_ctrl_write16(host, CTL_XFER_BLK_COUNT, data->blocks);
return 0;
}
@@ -449,8 +420,6 @@ fail:
static void tmio_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
{
struct tmio_mmc_host *host = mmc_priv(mmc);
- void __iomem *cnf = host->cnf;
- void __iomem *ctl = host->ctl;
if (ios->clock)
tmio_mmc_set_clock(host, ios->clock);
@@ -458,12 +427,12 @@ static void tmio_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
/* Power sequence - OFF -> ON -> UP */
switch (ios->power_mode) {
case MMC_POWER_OFF: /* power down SD bus */
- tmio_iowrite8(0x00, cnf + CNF_PWR_CTL_2);
+ sd_config_write8(host, CNF_PWR_CTL_2, 0x00);
tmio_mmc_clk_stop(host);
break;
case MMC_POWER_ON: /* power up SD bus */
- tmio_iowrite8(0x02, cnf + CNF_PWR_CTL_2);
+ sd_config_write8(host, CNF_PWR_CTL_2, 0x02);
break;
case MMC_POWER_UP: /* start bus clock */
tmio_mmc_clk_start(host);
@@ -472,10 +441,10 @@ static void tmio_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
switch (ios->bus_width) {
case MMC_BUS_WIDTH_1:
- tmio_iowrite16(0x80e0, ctl + CTL_SD_MEM_CARD_OPT);
+ sd_ctrl_write16(host, CTL_SD_MEM_CARD_OPT, 0x80e0);
break;
case MMC_BUS_WIDTH_4:
- tmio_iowrite16(0x00e0, ctl + CTL_SD_MEM_CARD_OPT);
+ sd_ctrl_write16(host, CTL_SD_MEM_CARD_OPT, 0x00e0);
break;
}
@@ -486,9 +455,8 @@ static void tmio_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
static int tmio_mmc_get_ro(struct mmc_host *mmc)
{
struct tmio_mmc_host *host = mmc_priv(mmc);
- void __iomem *ctl = host->ctl;
- return (tmio_ioread16(ctl + CTL_STATUS) & TMIO_STAT_WRPROTECT) ? 0 : 1;
+ return (sd_ctrl_read16(host, CTL_STATUS) & TMIO_STAT_WRPROTECT) ? 0 : 1;
}
static struct mmc_host_ops tmio_mmc_ops = {
@@ -518,13 +486,8 @@ static int tmio_mmc_resume(struct platform_device *dev)
struct mfd_cell *cell = (struct mfd_cell *)dev->dev.platform_data;
struct mmc_host *mmc = platform_get_drvdata(dev);
struct tmio_mmc_host *host = mmc_priv(mmc);
- void __iomem *cnf = host->cnf;
int ret = 0;
- /* Enable the MMC/SD Control registers */
- tmio_iowrite16(SDCREN, cnf + CNF_CMD);
- tmio_iowrite32(dev->resource[0].start & 0xfffe, cnf + CNF_CTL_BASE);
-
/* Tell the MFD core we are ready to be enabled */
if (cell->enable) {
ret = cell->enable(dev);
@@ -532,6 +495,11 @@ static int tmio_mmc_resume(struct platform_device *dev)
goto out;
}
+ /* Enable the MMC/SD Control registers */
+ sd_config_write16(host, CNF_CMD, SDCREN);
+ sd_config_write32(host, CNF_CTL_BASE,
+ (dev->resource[0].start >> host->bus_shift) & 0xfffe);
+
mmc_resume_host(mmc);
out:
@@ -545,20 +513,25 @@ out:
static int __devinit tmio_mmc_probe(struct platform_device *dev)
{
struct mfd_cell *cell = (struct mfd_cell *)dev->dev.platform_data;
+ struct tmio_mmc_data *pdata;
struct resource *res_ctl, *res_cnf;
struct tmio_mmc_host *host;
struct mmc_host *mmc;
- int ret = -ENOMEM;
+ int ret = -EINVAL;
if (dev->num_resources != 3)
goto out;
res_ctl = platform_get_resource(dev, IORESOURCE_MEM, 0);
res_cnf = platform_get_resource(dev, IORESOURCE_MEM, 1);
- if (!res_ctl || !res_cnf) {
- ret = -EINVAL;
+ if (!res_ctl || !res_cnf)
goto out;
- }
+
+ pdata = cell->driver_data;
+ if (!pdata || !pdata->hclk)
+ goto out;
+
+ ret = -ENOMEM;
mmc = mmc_alloc_host(sizeof(struct tmio_mmc_host), &dev->dev);
if (!mmc)
@@ -568,6 +541,9 @@ static int __devinit tmio_mmc_probe(struct platform_device *dev)
host->mmc = mmc;
platform_set_drvdata(dev, mmc);
+ /* SD control register space size is 0x200, 0x400 for bus_shift=1 */
+ host->bus_shift = resource_size(res_ctl) >> 10;
+
host->ctl = ioremap(res_ctl->start, resource_size(res_ctl));
if (!host->ctl)
goto host_free;
@@ -578,15 +554,10 @@ static int __devinit tmio_mmc_probe(struct platform_device *dev)
mmc->ops = &tmio_mmc_ops;
mmc->caps = MMC_CAP_4_BIT_DATA;
- mmc->f_min = 46875; /* 24000000 / 512 */
- mmc->f_max = 24000000;
+ mmc->f_max = pdata->hclk;
+ mmc->f_min = mmc->f_max / 512;
mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
- /* Enable the MMC/SD Control registers */
- tmio_iowrite16(SDCREN, host->cnf + CNF_CMD);
- tmio_iowrite32(dev->resource[0].start & 0xfffe,
- host->cnf + CNF_CTL_BASE);
-
/* Tell the MFD core we are ready to be enabled */
if (cell->enable) {
ret = cell->enable(dev);
@@ -594,14 +565,19 @@ static int __devinit tmio_mmc_probe(struct platform_device *dev)
goto unmap_cnf;
}
+ /* Enable the MMC/SD Control registers */
+ sd_config_write16(host, CNF_CMD, SDCREN);
+ sd_config_write32(host, CNF_CTL_BASE,
+ (dev->resource[0].start >> host->bus_shift) & 0xfffe);
+
/* Disable SD power during suspend */
- tmio_iowrite8(0x01, host->cnf + CNF_PWR_CTL_3);
+ sd_config_write8(host, CNF_PWR_CTL_3, 0x01);
/* The below is required but why? FIXME */
- tmio_iowrite8(0x1f, host->cnf + CNF_STOP_CLK_CTL);
+ sd_config_write8(host, CNF_STOP_CLK_CTL, 0x1f);
/* Power down SD bus*/
- tmio_iowrite8(0x0, host->cnf + CNF_PWR_CTL_2);
+ sd_config_write8(host, CNF_PWR_CTL_2, 0x00);
tmio_mmc_clk_stop(host);
reset(host);
@@ -612,22 +588,20 @@ static int __devinit tmio_mmc_probe(struct platform_device *dev)
else
goto unmap_cnf;
- disable_mmc_irqs(host->ctl, TMIO_MASK_ALL);
+ disable_mmc_irqs(host, TMIO_MASK_ALL);
- ret = request_irq(host->irq, tmio_mmc_irq, IRQF_DISABLED, "tmio-mmc",
- host);
+ ret = request_irq(host->irq, tmio_mmc_irq, IRQF_DISABLED |
+ IRQF_TRIGGER_FALLING, "tmio-mmc", host);
if (ret)
goto unmap_cnf;
- set_irq_type(host->irq, IRQ_TYPE_EDGE_FALLING);
-
mmc_add_host(mmc);
printk(KERN_INFO "%s at 0x%08lx irq %d\n", mmc_hostname(host->mmc),
(unsigned long)host->ctl, host->irq);
/* Unmask the IRQs we want to know about */
- enable_mmc_irqs(host->ctl, TMIO_MASK_IRQ);
+ enable_mmc_irqs(host, TMIO_MASK_IRQ);
return 0;
diff --git a/drivers/mmc/host/tmio_mmc.h b/drivers/mmc/host/tmio_mmc.h
index 9c831ab2ece..9fa99859497 100644
--- a/drivers/mmc/host/tmio_mmc.h
+++ b/drivers/mmc/host/tmio_mmc.h
@@ -83,34 +83,36 @@
TMIO_STAT_CARD_REMOVE | TMIO_STAT_CARD_INSERT)
#define TMIO_MASK_IRQ (TMIO_MASK_READOP | TMIO_MASK_WRITEOP | TMIO_MASK_CMD)
-#define enable_mmc_irqs(ctl, i) \
+
+#define enable_mmc_irqs(host, i) \
do { \
u32 mask;\
- mask = tmio_ioread32((ctl) + CTL_IRQ_MASK); \
+ mask = sd_ctrl_read32((host), CTL_IRQ_MASK); \
mask &= ~((i) & TMIO_MASK_IRQ); \
- tmio_iowrite32(mask, (ctl) + CTL_IRQ_MASK); \
+ sd_ctrl_write32((host), CTL_IRQ_MASK, mask); \
} while (0)
-#define disable_mmc_irqs(ctl, i) \
+#define disable_mmc_irqs(host, i) \
do { \
u32 mask;\
- mask = tmio_ioread32((ctl) + CTL_IRQ_MASK); \
+ mask = sd_ctrl_read32((host), CTL_IRQ_MASK); \
mask |= ((i) & TMIO_MASK_IRQ); \
- tmio_iowrite32(mask, (ctl) + CTL_IRQ_MASK); \
+ sd_ctrl_write32((host), CTL_IRQ_MASK, mask); \
} while (0)
-#define ack_mmc_irqs(ctl, i) \
+#define ack_mmc_irqs(host, i) \
do { \
u32 mask;\
- mask = tmio_ioread32((ctl) + CTL_STATUS); \
+ mask = sd_ctrl_read32((host), CTL_STATUS); \
mask &= ~((i) & TMIO_MASK_IRQ); \
- tmio_iowrite32(mask, (ctl) + CTL_STATUS); \
+ sd_ctrl_write32((host), CTL_STATUS, mask); \
} while (0)
struct tmio_mmc_host {
void __iomem *cnf;
void __iomem *ctl;
+ unsigned long bus_shift;
struct mmc_command *cmd;
struct mmc_request *mrq;
struct mmc_data *data;
@@ -123,6 +125,63 @@ struct tmio_mmc_host {
unsigned int sg_off;
};
+#include <linux/io.h>
+
+static inline u16 sd_ctrl_read16(struct tmio_mmc_host *host, int addr)
+{
+ return readw(host->ctl + (addr << host->bus_shift));
+}
+
+static inline void sd_ctrl_read16_rep(struct tmio_mmc_host *host, int addr,
+ u16 *buf, int count)
+{
+ readsw(host->ctl + (addr << host->bus_shift), buf, count);
+}
+
+static inline u32 sd_ctrl_read32(struct tmio_mmc_host *host, int addr)
+{
+ return readw(host->ctl + (addr << host->bus_shift)) |
+ readw(host->ctl + ((addr + 2) << host->bus_shift)) << 16;
+}
+
+static inline void sd_ctrl_write16(struct tmio_mmc_host *host, int addr,
+ u16 val)
+{
+ writew(val, host->ctl + (addr << host->bus_shift));
+}
+
+static inline void sd_ctrl_write16_rep(struct tmio_mmc_host *host, int addr,
+ u16 *buf, int count)
+{
+ writesw(host->ctl + (addr << host->bus_shift), buf, count);
+}
+
+static inline void sd_ctrl_write32(struct tmio_mmc_host *host, int addr,
+ u32 val)
+{
+ writew(val, host->ctl + (addr << host->bus_shift));
+ writew(val >> 16, host->ctl + ((addr + 2) << host->bus_shift));
+}
+
+static inline void sd_config_write8(struct tmio_mmc_host *host, int addr,
+ u8 val)
+{
+ writeb(val, host->cnf + (addr << host->bus_shift));
+}
+
+static inline void sd_config_write16(struct tmio_mmc_host *host, int addr,
+ u16 val)
+{
+ writew(val, host->cnf + (addr << host->bus_shift));
+}
+
+static inline void sd_config_write32(struct tmio_mmc_host *host, int addr,
+ u32 val)
+{
+ writew(val, host->cnf + (addr << host->bus_shift));
+ writew(val >> 16, host->cnf + ((addr + 2) << host->bus_shift));
+}
+
#include <linux/scatterlist.h>
#include <linux/blkdev.h>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-12-11 08:14:10 +0000