diff options
Diffstat (limited to 'drivers/mmc')
-rw-r--r-- | drivers/mmc/card/block.c | 26 | ||||
-rw-r--r-- | drivers/mmc/card/sdio_uart.c | 24 | ||||
-rw-r--r-- | drivers/mmc/core/sdio.c | 2 | ||||
-rw-r--r-- | drivers/mmc/host/at91_mci.c | 2 | ||||
-rw-r--r-- | drivers/mmc/host/atmel-mci.c | 8 | ||||
-rw-r--r-- | drivers/mmc/host/bfin_sdh.c | 7 | ||||
-rw-r--r-- | drivers/mmc/host/dw_mmc.c | 85 | ||||
-rw-r--r-- | drivers/mmc/host/mxs-mmc.c | 14 | ||||
-rw-r--r-- | drivers/mmc/host/omap.c | 16 | ||||
-rw-r--r-- | drivers/mmc/host/omap_hsmmc.c | 5 | ||||
-rw-r--r-- | drivers/mmc/host/sdhci-esdhc-imx.c | 2 | ||||
-rw-r--r-- | drivers/mmc/host/sdhci-esdhc.h | 6 | ||||
-rw-r--r-- | drivers/mmc/host/sdhci-tegra.c | 1 | ||||
-rw-r--r-- | drivers/mmc/host/vub300.c | 2 |
14 files changed, 116 insertions, 84 deletions
diff --git a/drivers/mmc/card/block.c b/drivers/mmc/card/block.c index f1c84decb19..172a768036d 100644 --- a/drivers/mmc/card/block.c +++ b/drivers/mmc/card/block.c @@ -1411,7 +1411,8 @@ static int mmc_blk_issue_rq(struct mmc_queue *mq, struct request *req) /* complete ongoing async transfer before issuing discard */ if (card->host->areq) mmc_blk_issue_rw_rq(mq, NULL); - if (req->cmd_flags & REQ_SECURE) + if (req->cmd_flags & REQ_SECURE && + !(card->quirks & MMC_QUIRK_SEC_ERASE_TRIM_BROKEN)) ret = mmc_blk_issue_secdiscard_rq(mq, req); else ret = mmc_blk_issue_discard_rq(mq, req); @@ -1716,6 +1717,7 @@ force_ro_fail: #define CID_MANFID_SANDISK 0x2 #define CID_MANFID_TOSHIBA 0x11 #define CID_MANFID_MICRON 0x13 +#define CID_MANFID_SAMSUNG 0x15 static const struct mmc_fixup blk_fixups[] = { @@ -1752,6 +1754,28 @@ static const struct mmc_fixup blk_fixups[] = MMC_FIXUP(CID_NAME_ANY, CID_MANFID_MICRON, 0x200, add_quirk_mmc, MMC_QUIRK_LONG_READ_TIME), + /* + * On these Samsung MoviNAND parts, performing secure erase or + * secure trim can result in unrecoverable corruption due to a + * firmware bug. + */ + MMC_FIXUP("M8G2FA", CID_MANFID_SAMSUNG, CID_OEMID_ANY, add_quirk_mmc, + MMC_QUIRK_SEC_ERASE_TRIM_BROKEN), + MMC_FIXUP("MAG4FA", CID_MANFID_SAMSUNG, CID_OEMID_ANY, add_quirk_mmc, + MMC_QUIRK_SEC_ERASE_TRIM_BROKEN), + MMC_FIXUP("MBG8FA", CID_MANFID_SAMSUNG, CID_OEMID_ANY, add_quirk_mmc, + MMC_QUIRK_SEC_ERASE_TRIM_BROKEN), + MMC_FIXUP("MCGAFA", CID_MANFID_SAMSUNG, CID_OEMID_ANY, add_quirk_mmc, + MMC_QUIRK_SEC_ERASE_TRIM_BROKEN), + MMC_FIXUP("VAL00M", CID_MANFID_SAMSUNG, CID_OEMID_ANY, add_quirk_mmc, + MMC_QUIRK_SEC_ERASE_TRIM_BROKEN), + MMC_FIXUP("VYL00M", CID_MANFID_SAMSUNG, CID_OEMID_ANY, add_quirk_mmc, + MMC_QUIRK_SEC_ERASE_TRIM_BROKEN), + MMC_FIXUP("KYL00M", CID_MANFID_SAMSUNG, CID_OEMID_ANY, add_quirk_mmc, + MMC_QUIRK_SEC_ERASE_TRIM_BROKEN), + MMC_FIXUP("VZL00M", CID_MANFID_SAMSUNG, CID_OEMID_ANY, add_quirk_mmc, + MMC_QUIRK_SEC_ERASE_TRIM_BROKEN), + END_FIXUP }; diff --git a/drivers/mmc/card/sdio_uart.c b/drivers/mmc/card/sdio_uart.c index 5a2cbfac66d..d2339ea3781 100644 --- a/drivers/mmc/card/sdio_uart.c +++ b/drivers/mmc/card/sdio_uart.c @@ -518,7 +518,7 @@ static void sdio_uart_check_modem_status(struct sdio_uart_port *port) if (status & UART_MSR_DCTS) { port->icount.cts++; tty = tty_port_tty_get(&port->port); - if (tty && (tty->termios->c_cflag & CRTSCTS)) { + if (tty && (tty->termios.c_cflag & CRTSCTS)) { int cts = (status & UART_MSR_CTS); if (tty->hw_stopped) { if (cts) { @@ -671,12 +671,12 @@ static int sdio_uart_activate(struct tty_port *tport, struct tty_struct *tty) port->ier = UART_IER_RLSI|UART_IER_RDI|UART_IER_RTOIE|UART_IER_UUE; port->mctrl = TIOCM_OUT2; - sdio_uart_change_speed(port, tty->termios, NULL); + sdio_uart_change_speed(port, &tty->termios, NULL); - if (tty->termios->c_cflag & CBAUD) + if (tty->termios.c_cflag & CBAUD) sdio_uart_set_mctrl(port, TIOCM_RTS | TIOCM_DTR); - if (tty->termios->c_cflag & CRTSCTS) + if (tty->termios.c_cflag & CRTSCTS) if (!(sdio_uart_get_mctrl(port) & TIOCM_CTS)) tty->hw_stopped = 1; @@ -850,7 +850,7 @@ static void sdio_uart_throttle(struct tty_struct *tty) { struct sdio_uart_port *port = tty->driver_data; - if (!I_IXOFF(tty) && !(tty->termios->c_cflag & CRTSCTS)) + if (!I_IXOFF(tty) && !(tty->termios.c_cflag & CRTSCTS)) return; if (sdio_uart_claim_func(port) != 0) @@ -861,7 +861,7 @@ static void sdio_uart_throttle(struct tty_struct *tty) sdio_uart_start_tx(port); } - if (tty->termios->c_cflag & CRTSCTS) + if (tty->termios.c_cflag & CRTSCTS) sdio_uart_clear_mctrl(port, TIOCM_RTS); sdio_uart_irq(port->func); @@ -872,7 +872,7 @@ static void sdio_uart_unthrottle(struct tty_struct *tty) { struct sdio_uart_port *port = tty->driver_data; - if (!I_IXOFF(tty) && !(tty->termios->c_cflag & CRTSCTS)) + if (!I_IXOFF(tty) && !(tty->termios.c_cflag & CRTSCTS)) return; if (sdio_uart_claim_func(port) != 0) @@ -887,7 +887,7 @@ static void sdio_uart_unthrottle(struct tty_struct *tty) } } - if (tty->termios->c_cflag & CRTSCTS) + if (tty->termios.c_cflag & CRTSCTS) sdio_uart_set_mctrl(port, TIOCM_RTS); sdio_uart_irq(port->func); @@ -898,12 +898,12 @@ static void sdio_uart_set_termios(struct tty_struct *tty, struct ktermios *old_termios) { struct sdio_uart_port *port = tty->driver_data; - unsigned int cflag = tty->termios->c_cflag; + unsigned int cflag = tty->termios.c_cflag; if (sdio_uart_claim_func(port) != 0) return; - sdio_uart_change_speed(port, tty->termios, old_termios); + sdio_uart_change_speed(port, &tty->termios, old_termios); /* Handle transition to B0 status */ if ((old_termios->c_cflag & CBAUD) && !(cflag & CBAUD)) @@ -1132,8 +1132,8 @@ static int sdio_uart_probe(struct sdio_func *func, kfree(port); } else { struct device *dev; - dev = tty_register_device(sdio_uart_tty_driver, - port->index, &func->dev); + dev = tty_port_register_device(&port->port, + sdio_uart_tty_driver, port->index, &func->dev); if (IS_ERR(dev)) { sdio_uart_port_remove(port); ret = PTR_ERR(dev); diff --git a/drivers/mmc/core/sdio.c b/drivers/mmc/core/sdio.c index d4619e2ec03..2273ce6b6c1 100644 --- a/drivers/mmc/core/sdio.c +++ b/drivers/mmc/core/sdio.c @@ -641,7 +641,7 @@ static int mmc_sdio_init_card(struct mmc_host *host, u32 ocr, /* * If the host and card support UHS-I mode request the card * to switch to 1.8V signaling level. No 1.8v signalling if - * UHS mode is not enabled to maintain compatibilty and some + * UHS mode is not enabled to maintain compatibility and some * systems that claim 1.8v signalling in fact do not support * it. */ diff --git a/drivers/mmc/host/at91_mci.c b/drivers/mmc/host/at91_mci.c index efdb81d21c4..74bed0fc23e 100644 --- a/drivers/mmc/host/at91_mci.c +++ b/drivers/mmc/host/at91_mci.c @@ -356,7 +356,7 @@ static void at91_mci_handle_transmitted(struct at91mci_host *host) } /* - * Update bytes tranfered count during a write operation + * Update bytes transfered count during a write operation */ static void at91_mci_update_bytes_xfered(struct at91mci_host *host) { diff --git a/drivers/mmc/host/atmel-mci.c b/drivers/mmc/host/atmel-mci.c index 322412cec4e..852d5fbda63 100644 --- a/drivers/mmc/host/atmel-mci.c +++ b/drivers/mmc/host/atmel-mci.c @@ -81,6 +81,7 @@ struct atmel_mci_caps { bool has_bad_data_ordering; bool need_reset_after_xfer; bool need_blksz_mul_4; + bool need_notbusy_for_read_ops; }; struct atmel_mci_dma { @@ -1021,7 +1022,7 @@ static void atmci_stop_transfer(struct atmel_mci *host) } /* - * Stop data transfer because error(s) occured. + * Stop data transfer because error(s) occurred. */ static void atmci_stop_transfer_pdc(struct atmel_mci *host) { @@ -1625,7 +1626,8 @@ static void atmci_tasklet_func(unsigned long priv) __func__); atmci_set_completed(host, EVENT_XFER_COMPLETE); - if (host->data->flags & MMC_DATA_WRITE) { + if (host->caps.need_notbusy_for_read_ops || + (host->data->flags & MMC_DATA_WRITE)) { atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY); state = STATE_WAITING_NOTBUSY; } else if (host->mrq->stop) { @@ -2218,6 +2220,7 @@ static void __init atmci_get_cap(struct atmel_mci *host) host->caps.has_bad_data_ordering = 1; host->caps.need_reset_after_xfer = 1; host->caps.need_blksz_mul_4 = 1; + host->caps.need_notbusy_for_read_ops = 0; /* keep only major version number */ switch (version & 0xf00) { @@ -2238,6 +2241,7 @@ static void __init atmci_get_cap(struct atmel_mci *host) case 0x200: host->caps.has_rwproof = 1; host->caps.need_blksz_mul_4 = 0; + host->caps.need_notbusy_for_read_ops = 1; case 0x100: host->caps.has_bad_data_ordering = 0; host->caps.need_reset_after_xfer = 0; diff --git a/drivers/mmc/host/bfin_sdh.c b/drivers/mmc/host/bfin_sdh.c index 03666174ca4..a17dd7363ce 100644 --- a/drivers/mmc/host/bfin_sdh.c +++ b/drivers/mmc/host/bfin_sdh.c @@ -49,13 +49,6 @@ #define bfin_write_SDH_CFG bfin_write_RSI_CFG #endif -struct dma_desc_array { - unsigned long start_addr; - unsigned short cfg; - unsigned short x_count; - short x_modify; -} __packed; - struct sdh_host { struct mmc_host *mmc; spinlock_t lock; diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c index 72dc3cde646..af40d227bec 100644 --- a/drivers/mmc/host/dw_mmc.c +++ b/drivers/mmc/host/dw_mmc.c @@ -627,6 +627,7 @@ static void dw_mci_setup_bus(struct dw_mci_slot *slot) { struct dw_mci *host = slot->host; u32 div; + u32 clk_en_a; if (slot->clock != host->current_speed) { div = host->bus_hz / slot->clock; @@ -659,9 +660,11 @@ static void dw_mci_setup_bus(struct dw_mci_slot *slot) mci_send_cmd(slot, SDMMC_CMD_UPD_CLK | SDMMC_CMD_PRV_DAT_WAIT, 0); - /* enable clock */ - mci_writel(host, CLKENA, ((SDMMC_CLKEN_ENABLE | - SDMMC_CLKEN_LOW_PWR) << slot->id)); + /* enable clock; only low power if no SDIO */ + clk_en_a = SDMMC_CLKEN_ENABLE << slot->id; + if (!(mci_readl(host, INTMASK) & SDMMC_INT_SDIO(slot->id))) + clk_en_a |= SDMMC_CLKEN_LOW_PWR << slot->id; + mci_writel(host, CLKENA, clk_en_a); /* inform CIU */ mci_send_cmd(slot, @@ -862,6 +865,30 @@ static int dw_mci_get_cd(struct mmc_host *mmc) return present; } +/* + * Disable lower power mode. + * + * Low power mode will stop the card clock when idle. According to the + * description of the CLKENA register we should disable low power mode + * for SDIO cards if we need SDIO interrupts to work. + * + * This function is fast if low power mode is already disabled. + */ +static void dw_mci_disable_low_power(struct dw_mci_slot *slot) +{ + struct dw_mci *host = slot->host; + u32 clk_en_a; + const u32 clken_low_pwr = SDMMC_CLKEN_LOW_PWR << slot->id; + + clk_en_a = mci_readl(host, CLKENA); + + if (clk_en_a & clken_low_pwr) { + mci_writel(host, CLKENA, clk_en_a & ~clken_low_pwr); + mci_send_cmd(slot, SDMMC_CMD_UPD_CLK | + SDMMC_CMD_PRV_DAT_WAIT, 0); + } +} + static void dw_mci_enable_sdio_irq(struct mmc_host *mmc, int enb) { struct dw_mci_slot *slot = mmc_priv(mmc); @@ -871,6 +898,14 @@ static void dw_mci_enable_sdio_irq(struct mmc_host *mmc, int enb) /* Enable/disable Slot Specific SDIO interrupt */ int_mask = mci_readl(host, INTMASK); if (enb) { + /* + * Turn off low power mode if it was enabled. This is a bit of + * a heavy operation and we disable / enable IRQs a lot, so + * we'll leave low power mode disabled and it will get + * re-enabled again in dw_mci_setup_bus(). + */ + dw_mci_disable_low_power(slot); + mci_writel(host, INTMASK, (int_mask | SDMMC_INT_SDIO(slot->id))); } else { @@ -1429,22 +1464,10 @@ static void dw_mci_read_data_pio(struct dw_mci *host) nbytes += len; remain -= len; } while (remain); - sg_miter->consumed = offset; + sg_miter->consumed = offset; status = mci_readl(host, MINTSTS); mci_writel(host, RINTSTS, SDMMC_INT_RXDR); - if (status & DW_MCI_DATA_ERROR_FLAGS) { - host->data_status = status; - data->bytes_xfered += nbytes; - sg_miter_stop(sg_miter); - host->sg = NULL; - smp_wmb(); - - set_bit(EVENT_DATA_ERROR, &host->pending_events); - - tasklet_schedule(&host->tasklet); - return; - } } while (status & SDMMC_INT_RXDR); /*if the RXDR is ready read again*/ data->bytes_xfered += nbytes; @@ -1497,23 +1520,10 @@ static void dw_mci_write_data_pio(struct dw_mci *host) nbytes += len; remain -= len; } while (remain); - sg_miter->consumed = offset; + sg_miter->consumed = offset; status = mci_readl(host, MINTSTS); mci_writel(host, RINTSTS, SDMMC_INT_TXDR); - if (status & DW_MCI_DATA_ERROR_FLAGS) { - host->data_status = status; - data->bytes_xfered += nbytes; - sg_miter_stop(sg_miter); - host->sg = NULL; - - smp_wmb(); - - set_bit(EVENT_DATA_ERROR, &host->pending_events); - - tasklet_schedule(&host->tasklet); - return; - } } while (status & SDMMC_INT_TXDR); /* if TXDR write again */ data->bytes_xfered += nbytes; @@ -1547,12 +1557,11 @@ static void dw_mci_cmd_interrupt(struct dw_mci *host, u32 status) static irqreturn_t dw_mci_interrupt(int irq, void *dev_id) { struct dw_mci *host = dev_id; - u32 status, pending; + u32 pending; unsigned int pass_count = 0; int i; do { - status = mci_readl(host, RINTSTS); pending = mci_readl(host, MINTSTS); /* read-only mask reg */ /* @@ -1570,7 +1579,7 @@ static irqreturn_t dw_mci_interrupt(int irq, void *dev_id) if (pending & DW_MCI_CMD_ERROR_FLAGS) { mci_writel(host, RINTSTS, DW_MCI_CMD_ERROR_FLAGS); - host->cmd_status = status; + host->cmd_status = pending; smp_wmb(); set_bit(EVENT_CMD_COMPLETE, &host->pending_events); } @@ -1578,18 +1587,16 @@ static irqreturn_t dw_mci_interrupt(int irq, void *dev_id) if (pending & DW_MCI_DATA_ERROR_FLAGS) { /* if there is an error report DATA_ERROR */ mci_writel(host, RINTSTS, DW_MCI_DATA_ERROR_FLAGS); - host->data_status = status; + host->data_status = pending; smp_wmb(); set_bit(EVENT_DATA_ERROR, &host->pending_events); - if (!(pending & (SDMMC_INT_DTO | SDMMC_INT_DCRC | - SDMMC_INT_SBE | SDMMC_INT_EBE))) - tasklet_schedule(&host->tasklet); + tasklet_schedule(&host->tasklet); } if (pending & SDMMC_INT_DATA_OVER) { mci_writel(host, RINTSTS, SDMMC_INT_DATA_OVER); if (!host->data_status) - host->data_status = status; + host->data_status = pending; smp_wmb(); if (host->dir_status == DW_MCI_RECV_STATUS) { if (host->sg != NULL) @@ -1613,7 +1620,7 @@ static irqreturn_t dw_mci_interrupt(int irq, void *dev_id) if (pending & SDMMC_INT_CMD_DONE) { mci_writel(host, RINTSTS, SDMMC_INT_CMD_DONE); - dw_mci_cmd_interrupt(host, status); + dw_mci_cmd_interrupt(host, pending); } if (pending & SDMMC_INT_CD) { diff --git a/drivers/mmc/host/mxs-mmc.c b/drivers/mmc/host/mxs-mmc.c index a51f9309ffb..ad3fcea1269 100644 --- a/drivers/mmc/host/mxs-mmc.c +++ b/drivers/mmc/host/mxs-mmc.c @@ -285,11 +285,11 @@ static irqreturn_t mxs_mmc_irq_handler(int irq, void *dev_id) writel(stat & MXS_MMC_IRQ_BITS, host->base + HW_SSP_CTRL1(host) + STMP_OFFSET_REG_CLR); + spin_unlock(&host->lock); + if ((stat & BM_SSP_CTRL1_SDIO_IRQ) && (stat & BM_SSP_CTRL1_SDIO_IRQ_EN)) mmc_signal_sdio_irq(host->mmc); - spin_unlock(&host->lock); - if (stat & BM_SSP_CTRL1_RESP_TIMEOUT_IRQ) cmd->error = -ETIMEDOUT; else if (stat & BM_SSP_CTRL1_RESP_ERR_IRQ) @@ -644,11 +644,6 @@ static void mxs_mmc_enable_sdio_irq(struct mmc_host *mmc, int enable) host->base + HW_SSP_CTRL0 + STMP_OFFSET_REG_SET); writel(BM_SSP_CTRL1_SDIO_IRQ_EN, host->base + HW_SSP_CTRL1(host) + STMP_OFFSET_REG_SET); - - if (readl(host->base + HW_SSP_STATUS(host)) & - BM_SSP_STATUS_SDIO_IRQ) - mmc_signal_sdio_irq(host->mmc); - } else { writel(BM_SSP_CTRL0_SDIO_IRQ_CHECK, host->base + HW_SSP_CTRL0 + STMP_OFFSET_REG_CLR); @@ -657,6 +652,11 @@ static void mxs_mmc_enable_sdio_irq(struct mmc_host *mmc, int enable) } spin_unlock_irqrestore(&host->lock, flags); + + if (enable && readl(host->base + HW_SSP_STATUS(host)) & + BM_SSP_STATUS_SDIO_IRQ) + mmc_signal_sdio_irq(host->mmc); + } static const struct mmc_host_ops mxs_mmc_ops = { diff --git a/drivers/mmc/host/omap.c b/drivers/mmc/host/omap.c index 50e08f03aa6..c6259a82954 100644 --- a/drivers/mmc/host/omap.c +++ b/drivers/mmc/host/omap.c @@ -33,11 +33,9 @@ #include <asm/io.h> #include <asm/irq.h> -#include <plat/board.h> #include <plat/mmc.h> #include <asm/gpio.h> #include <plat/dma.h> -#include <plat/mux.h> #include <plat/fpga.h> #define OMAP_MMC_REG_CMD 0x00 @@ -668,7 +666,7 @@ mmc_omap_clk_timer(unsigned long data) static void mmc_omap_xfer_data(struct mmc_omap_host *host, int write) { - int n; + int n, nwords; if (host->buffer_bytes_left == 0) { host->sg_idx++; @@ -678,15 +676,23 @@ mmc_omap_xfer_data(struct mmc_omap_host *host, int write) n = 64; if (n > host->buffer_bytes_left) n = host->buffer_bytes_left; + + nwords = n / 2; + nwords += n & 1; /* handle odd number of bytes to transfer */ + host->buffer_bytes_left -= n; host->total_bytes_left -= n; host->data->bytes_xfered += n; if (write) { - __raw_writesw(host->virt_base + OMAP_MMC_REG(host, DATA), host->buffer, n); + __raw_writesw(host->virt_base + OMAP_MMC_REG(host, DATA), + host->buffer, nwords); } else { - __raw_readsw(host->virt_base + OMAP_MMC_REG(host, DATA), host->buffer, n); + __raw_readsw(host->virt_base + OMAP_MMC_REG(host, DATA), + host->buffer, nwords); } + + host->buffer += nwords; } static inline void mmc_omap_report_irq(u16 status) diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c index 3a09f93cc3b..38adc330c00 100644 --- a/drivers/mmc/host/omap_hsmmc.c +++ b/drivers/mmc/host/omap_hsmmc.c @@ -40,7 +40,6 @@ #include <linux/regulator/consumer.h> #include <linux/pm_runtime.h> #include <mach/hardware.h> -#include <plat/board.h> #include <plat/mmc.h> #include <plat/cpu.h> @@ -447,7 +446,7 @@ static void omap_hsmmc_stop_clock(struct omap_hsmmc_host *host) OMAP_HSMMC_WRITE(host->base, SYSCTL, OMAP_HSMMC_READ(host->base, SYSCTL) & ~CEN); if ((OMAP_HSMMC_READ(host->base, SYSCTL) & CEN) != 0x0) - dev_dbg(mmc_dev(host->mmc), "MMC Clock is not stoped\n"); + dev_dbg(mmc_dev(host->mmc), "MMC Clock is not stopped\n"); } static void omap_hsmmc_enable_irq(struct omap_hsmmc_host *host, @@ -1782,7 +1781,7 @@ static int __devinit omap_hsmmc_probe(struct platform_device *pdev) if (match) { pdata = of_get_hsmmc_pdata(&pdev->dev); if (match->data) { - u16 *offsetp = match->data; + const u16 *offsetp = match->data; pdata->reg_offset = *offsetp; } } diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c index e23f8134591..32f4a070551 100644 --- a/drivers/mmc/host/sdhci-esdhc-imx.c +++ b/drivers/mmc/host/sdhci-esdhc-imx.c @@ -315,7 +315,7 @@ static void esdhc_writeb_le(struct sdhci_host *host, u8 val, int reg) new_val = val & (SDHCI_CTRL_LED | \ SDHCI_CTRL_4BITBUS | \ SDHCI_CTRL_D3CD); - /* ensure the endianess */ + /* ensure the endianness */ new_val |= ESDHC_HOST_CONTROL_LE; /* bits 8&9 are reserved on mx25 */ if (!is_imx25_esdhc(imx_data)) { diff --git a/drivers/mmc/host/sdhci-esdhc.h b/drivers/mmc/host/sdhci-esdhc.h index b97b2f5dafd..d25f9ab9a54 100644 --- a/drivers/mmc/host/sdhci-esdhc.h +++ b/drivers/mmc/host/sdhci-esdhc.h @@ -48,14 +48,14 @@ static inline void esdhc_set_clock(struct sdhci_host *host, unsigned int clock) int div = 1; u32 temp; + if (clock == 0) + goto out; + temp = sdhci_readl(host, ESDHC_SYSTEM_CONTROL); temp &= ~(ESDHC_CLOCK_IPGEN | ESDHC_CLOCK_HCKEN | ESDHC_CLOCK_PEREN | ESDHC_CLOCK_MASK); sdhci_writel(host, temp, ESDHC_SYSTEM_CONTROL); - if (clock == 0) - goto out; - while (host->max_clk / pre_div / 16 > clock && pre_div < 256) pre_div *= 2; diff --git a/drivers/mmc/host/sdhci-tegra.c b/drivers/mmc/host/sdhci-tegra.c index 0810ccc23d7..5393c64de3c 100644 --- a/drivers/mmc/host/sdhci-tegra.c +++ b/drivers/mmc/host/sdhci-tegra.c @@ -27,7 +27,6 @@ #include <asm/gpio.h> -#include <mach/gpio-tegra.h> #include <mach/sdhci.h> #include "sdhci-pltfm.h" diff --git a/drivers/mmc/host/vub300.c b/drivers/mmc/host/vub300.c index 3135a1a5d75..58eab9ac1d0 100644 --- a/drivers/mmc/host/vub300.c +++ b/drivers/mmc/host/vub300.c @@ -806,7 +806,7 @@ static void command_res_completed(struct urb *urb) * we suspect a buggy USB host controller */ } else if (!vub300->data) { - /* this means that the command (typically CMD52) suceeded */ + /* this means that the command (typically CMD52) succeeded */ } else if (vub300->resp.common.header_type != 0x02) { /* * this is an error response from the VUB300 chip |