1 files changed, 541 insertions, 12 deletions

diff --git a/drivers/mtd/devices/docg3.c b/drivers/mtd/devices/docg3.c
index 27c4feae132..fd4d47bdeec 100644
--- a/drivers/mtd/devices/docg3.c
+++ b/drivers/mtd/devices/docg3.c
@@ -254,6 +254,40 @@ static void doc_read_data_area(struct docg3 *docg3, void *buf, int len,
 }
 
 /**
+ * doc_write_data_area - Write data into data area
+ * @docg3: the device
+ * @buf: the buffer to get input bytes from
+ * @len: the length to write
+ *
+ * Writes bytes into flash data. Handles the single byte / even bytes writes.
+ */
+static void doc_write_data_area(struct docg3 *docg3, const void *buf, int len)
+{
+	int i, cdr, len4;
+	u16 *src16;
+	u8 *src8;
+
+	doc_dbg("doc_write_data_area(buf=%p, len=%d)\n", buf, len);
+	cdr = len & 0x3;
+	len4 = len - cdr;
+
+	doc_writew(docg3, DOC_IOSPACE_DATA, DOC_READADDRESS);
+	src16 = (u16 *)buf;
+	for (i = 0; i < len4; i += 2) {
+		doc_writew(docg3, *src16, DOC_IOSPACE_DATA);
+		src16++;
+	}
+
+	src8 = (u8 *)src16;
+	for (i = 0; i < cdr; i++) {
+		doc_writew(docg3, DOC_IOSPACE_DATA | DOC_READADDR_ONE_BYTE,
+			   DOC_READADDRESS);
+		doc_writeb(docg3, *src8, DOC_IOSPACE_DATA);
+		src8++;
+	}
+}
+
+/**
  * doc_set_data_mode - Sets the flash to reliable data mode
  * @docg3: the device
  *
@@ -343,6 +377,37 @@ static int doc_set_extra_page_mode(struct docg3 *docg3)
 }
 
 /**
+ * doc_setup_addr_sector - Setup blocks/page/ofs address for one plane
+ * @docg3: the device
+ * @sector: the sector
+ */
+static void doc_setup_addr_sector(struct docg3 *docg3, int sector)
+{
+	doc_delay(docg3, 1);
+	doc_flash_address(docg3, sector & 0xff);
+	doc_flash_address(docg3, (sector >> 8) & 0xff);
+	doc_flash_address(docg3, (sector >> 16) & 0xff);
+	doc_delay(docg3, 1);
+}
+
+/**
+ * doc_setup_writeaddr_sector - Setup blocks/page/ofs address for one plane
+ * @docg3: the device
+ * @sector: the sector
+ * @ofs: the offset in the page, between 0 and (512 + 16 + 512)
+ */
+static void doc_setup_writeaddr_sector(struct docg3 *docg3, int sector, int ofs)
+{
+	ofs = ofs >> 2;
+	doc_delay(docg3, 1);
+	doc_flash_address(docg3, ofs & 0xff);
+	doc_flash_address(docg3, sector & 0xff);
+	doc_flash_address(docg3, (sector >> 8) & 0xff);
+	doc_flash_address(docg3, (sector >> 16) & 0xff);
+	doc_delay(docg3, 1);
+}
+
+/**
  * doc_seek - Set both flash planes to the specified block, page for reading
  * @docg3: the device
  * @block0: the first plane block index
@@ -378,27 +443,73 @@ static int doc_read_seek(struct docg3 *docg3, int block0, int block1, int page,
 	if (ret)
 		goto out;
 
-	sector = (block0 << DOC_ADDR_BLOCK_SHIFT) + (page & DOC_ADDR_PAGE_MASK);
 	doc_flash_sequence(docg3, DOC_SEQ_READ);
+	sector = (block0 << DOC_ADDR_BLOCK_SHIFT) + (page & DOC_ADDR_PAGE_MASK);
 	doc_flash_command(docg3, DOC_CMD_PROG_BLOCK_ADDR);
-	doc_delay(docg3, 1);
-	doc_flash_address(docg3, sector & 0xff);
-	doc_flash_address(docg3, (sector >> 8) & 0xff);
-	doc_flash_address(docg3, (sector >> 16) & 0xff);
-	doc_delay(docg3, 1);
+	doc_setup_addr_sector(docg3, sector);
 
 	sector = (block1 << DOC_ADDR_BLOCK_SHIFT) + (page & DOC_ADDR_PAGE_MASK);
 	doc_flash_command(docg3, DOC_CMD_PROG_BLOCK_ADDR);
+	doc_setup_addr_sector(docg3, sector);
 	doc_delay(docg3, 1);
-	doc_flash_address(docg3, sector & 0xff);
-	doc_flash_address(docg3, (sector >> 8) & 0xff);
-	doc_flash_address(docg3, (sector >> 16) & 0xff);
+
+out:
+	return ret;
+}
+
+/**
+ * doc_write_seek - Set both flash planes to the specified block, page for writing
+ * @docg3: the device
+ * @block0: the first plane block index
+ * @block1: the second plane block index
+ * @page: the page index within the block
+ * @ofs: offset in page to write
+ *
+ * Programs the flash even and odd planes to the specific block and page.
+ * Alternatively, programs the flash to the wear area of the specified page.
+ */
+static int doc_write_seek(struct docg3 *docg3, int block0, int block1, int page,
+			 int ofs)
+{
+	int ret = 0, sector;
+
+	doc_dbg("doc_write_seek(blocks=(%d,%d), page=%d, ofs=%d)\n",
+		block0, block1, page, ofs);
+
+	doc_set_reliable_mode(docg3);
+
+	if (ofs < 2 * DOC_LAYOUT_PAGE_SIZE) {
+		doc_flash_sequence(docg3, DOC_SEQ_SET_PLANE1);
+		doc_flash_command(docg3, DOC_CMD_READ_PLANE1);
+		doc_delay(docg3, 2);
+	} else {
+		doc_flash_sequence(docg3, DOC_SEQ_SET_PLANE2);
+		doc_flash_command(docg3, DOC_CMD_READ_PLANE2);
+		doc_delay(docg3, 2);
+	}
+
+	doc_flash_sequence(docg3, DOC_SEQ_PAGE_SETUP);
+	doc_flash_command(docg3, DOC_CMD_PROG_CYCLE1);
+
+	sector = (block0 << DOC_ADDR_BLOCK_SHIFT) + (page & DOC_ADDR_PAGE_MASK);
+	doc_setup_writeaddr_sector(docg3, sector, ofs);
+
+	doc_flash_command(docg3, DOC_CMD_PROG_CYCLE3);
 	doc_delay(docg3, 2);
+	ret = doc_wait_ready(docg3);
+	if (ret)
+		goto out;
+
+	doc_flash_command(docg3, DOC_CMD_PROG_CYCLE1);
+	sector = (block1 << DOC_ADDR_BLOCK_SHIFT) + (page & DOC_ADDR_PAGE_MASK);
+	doc_setup_writeaddr_sector(docg3, sector, ofs);
+	doc_delay(docg3, 1);
 
 out:
 	return ret;
 }
 
+
 /**
  * doc_read_page_ecc_init - Initialize hardware ECC engine
  * @docg3: the device
@@ -421,6 +532,58 @@ static int doc_read_page_ecc_init(struct docg3 *docg3, int len)
 }
 
 /**
+ * doc_write_page_ecc_init - Initialize hardware BCH ECC engine
+ * @docg3: the device
+ * @len: the number of bytes covered by the ECC (BCH covered)
+ *
+ * The function does initialize the hardware ECC engine to compute the Hamming
+ * ECC (on 1 byte) and the BCH Syndroms (on 7 bytes).
+ *
+ * Return 0 if succeeded, -EIO on error
+ */
+static int doc_write_page_ecc_init(struct docg3 *docg3, int len)
+{
+	doc_writew(docg3, !DOC_ECCCONF0_READ_MODE
+		   | DOC_ECCCONF0_BCH_ENABLE | DOC_ECCCONF0_HAMMING_ENABLE
+		   | (len & DOC_ECCCONF0_DATA_BYTES_MASK),
+		   DOC_ECCCONF0);
+	doc_delay(docg3, 4);
+	doc_register_readb(docg3, DOC_FLASHCONTROL);
+	return doc_wait_ready(docg3);
+}
+
+/**
+ * doc_ecc_disable - Disable Hamming and BCH ECC hardware calculator
+ * @docg3: the device
+ *
+ * Disables the hardware ECC generator and checker, for unchecked reads (as when
+ * reading OOB only or write status byte).
+ */
+static void doc_ecc_disable(struct docg3 *docg3)
+{
+	doc_writew(docg3, DOC_ECCCONF0_READ_MODE, DOC_ECCCONF0);
+	doc_delay(docg3, 4);
+}
+
+/**
+ * doc_hamming_ecc_init - Initialize hardware Hamming ECC engine
+ * @docg3: the device
+ * @nb_bytes: the number of bytes covered by the ECC (Hamming covered)
+ *
+ * This function programs the ECC hardware to compute the hamming code on the
+ * last provided N bytes to the hardware generator.
+ */
+static void doc_hamming_ecc_init(struct docg3 *docg3, int nb_bytes)
+{
+	u8 ecc_conf1;
+
+	ecc_conf1 = doc_register_readb(docg3, DOC_ECCCONF1);
+	ecc_conf1 &= ~DOC_ECCCONF1_HAMMING_BITS_MASK;
+	ecc_conf1 |= (nb_bytes & DOC_ECCCONF1_HAMMING_BITS_MASK);
+	doc_writeb(docg3, ecc_conf1, DOC_ECCCONF1);
+}
+
+/**
  * doc_read_page_prepare - Prepares reading data from a flash page
  * @docg3: the device
  * @block0: the first plane block index on flash memory
@@ -506,11 +669,25 @@ static int doc_read_page_getbytes(struct docg3 *docg3, int len, u_char *buf,
 }
 
 /**
+ * doc_write_page_putbytes - Writes bytes into a prepared page
+ * @docg3: the device
+ * @len: the number of bytes to be written
+ * @buf: the buffer of input bytes
+ *
+ */
+static void doc_write_page_putbytes(struct docg3 *docg3, int len,
+				    const u_char *buf)
+{
+	doc_write_data_area(docg3, buf, len);
+	doc_delay(docg3, 2);
+}
+
+/**
  * doc_get_hw_bch_syndroms - Get hardware calculated BCH syndroms
  * @docg3: the device
  * @syns:  the array of 7 integers where the syndroms will be stored
  */
-static void doc_get_hw_bch_syndroms(struct docg3 *docg3, int *syns)
+static void doc_get_hw_bch_syndroms(struct docg3 *docg3, u8 *syns)
 {
 	int i;
 
@@ -519,6 +696,16 @@ static void doc_get_hw_bch_syndroms(struct docg3 *docg3, int *syns)
 }
 
 /**
+ * doc_page_finish - Ends reading/writing of a flash page
+ * @docg3: the device
+ */
+static void doc_page_finish(struct docg3 *docg3)
+{
+	doc_writeb(docg3, 0, DOC_DATAEND);
+	doc_delay(docg3, 2);
+}
+
+/**
  * doc_read_page_finish - Ends reading of a flash page
  * @docg3: the device
  *
@@ -528,8 +715,7 @@ static void doc_get_hw_bch_syndroms(struct docg3 *docg3, int *syns)
  */
 static void doc_read_page_finish(struct docg3 *docg3)
 {
-	doc_writeb(docg3, 0, DOC_DATAEND);
-	doc_delay(docg3, 2);
+	doc_page_finish(docg3);
 	doc_set_device_id(docg3, 0);
 }
 
@@ -791,6 +977,348 @@ static int doc_get_erase_count(struct docg3 *docg3, loff_t from)
 	return max(plane1_erase_count, plane2_erase_count);
 }
 
+/**
+ * doc_get_op_status - get erase/write operation status
+ * @docg3: the device
+ *
+ * Queries the status from the chip, and returns it
+ *
+ * Returns the status (bits DOC_PLANES_STATUS_*)
+ */
+static int doc_get_op_status(struct docg3 *docg3)
+{
+	u8 status;
+
+	doc_flash_sequence(docg3, DOC_SEQ_PLANES_STATUS);
+	doc_flash_command(docg3, DOC_CMD_PLANES_STATUS);
+	doc_delay(docg3, 5);
+
+	doc_ecc_disable(docg3);
+	doc_read_data_area(docg3, &status, 1, 1);
+	return status;
+}
+
+/**
+ * doc_write_erase_wait_status - wait for write or erase completion
+ * @docg3: the device
+ *
+ * Wait for the chip to be ready again after erase or write operation, and check
+ * erase/write status.
+ *
+ * Returns 0 if erase successfull, -EIO if erase/write issue, -ETIMEOUT if
+ * timeout
+ */
+static int doc_write_erase_wait_status(struct docg3 *docg3)
+{
+	int status, ret = 0;
+
+	if (!doc_is_ready(docg3))
+		usleep_range(3000, 3000);
+	if (!doc_is_ready(docg3)) {
+		doc_dbg("Timeout reached and the chip is still not ready\n");
+		ret = -EAGAIN;
+		goto out;
+	}
+
+	status = doc_get_op_status(docg3);
+	if (status & DOC_PLANES_STATUS_FAIL) {
+		doc_dbg("Erase/Write failed on (a) plane(s), status = %x\n",
+			status);
+		ret = -EIO;
+	}
+
+out:
+	doc_page_finish(docg3);
+	return ret;
+}
+
+/**
+ * doc_write_page - Write a single page to the chip
+ * @docg3: the device
+ * @to: the offset from first block and first page, in bytes, aligned on page
+ *      size
+ * @buf: buffer to get bytes from
+ * @oob: buffer to get out of band bytes from (can be NULL if no OOB should be
+ *       written)
+ * @autoecc: if 0, all 16 bytes from OOB are taken, regardless of HW Hamming or
+ *           BCH computations. If 1, only bytes 0-7 and byte 15 are taken,
+ *           remaining ones are filled with hardware Hamming and BCH
+ *           computations. Its value is not meaningfull is oob == NULL.
+ *
+ * Write one full page (ie. 1 page split on two planes), of 512 bytes, with the
+ * OOB data. The OOB ECC is automatically computed by the hardware Hamming and
+ * BCH generator if autoecc is not null.
+ *
+ * Returns 0 if write successful, -EIO if write error, -EAGAIN if timeout
+ */
+static int doc_write_page(struct docg3 *docg3, loff_t to, const u_char *buf,
+			  const u_char *oob, int autoecc)
+{
+	int block0, block1, page, ret, ofs = 0;
+	u8 syn[DOC_ECC_BCH_SIZE], hamming;
+
+	doc_dbg("doc_write_page(to=%lld)\n", to);
+	calc_block_sector(to, &block0, &block1, &page, &ofs);
+
+	doc_set_device_id(docg3, docg3->device_id);
+	ret = doc_reset_seq(docg3);
+	if (ret)
+		goto err;
+
+	/* Program the flash address block and page */
+	ret = doc_write_seek(docg3, block0, block1, page, ofs);
+	if (ret)
+		goto err;
+
+	doc_write_page_ecc_init(docg3, DOC_ECC_BCH_COVERED_BYTES);
+	doc_delay(docg3, 2);
+	doc_write_page_putbytes(docg3, DOC_LAYOUT_PAGE_SIZE, buf);
+
+	if (oob && autoecc) {
+		doc_write_page_putbytes(docg3, DOC_LAYOUT_OOB_PAGEINFO_SZ, oob);
+		doc_delay(docg3, 2);
+		oob += DOC_LAYOUT_OOB_UNUSED_OFS;
+
+		hamming = doc_register_readb(docg3, DOC_HAMMINGPARITY);
+		doc_delay(docg3, 2);
+		doc_write_page_putbytes(docg3, DOC_LAYOUT_OOB_HAMMING_SZ,
+					&hamming);
+		doc_delay(docg3, 2);
+
+		doc_get_hw_bch_syndroms(docg3, syn);
+		doc_write_page_putbytes(docg3, DOC_LAYOUT_OOB_BCH_SZ, syn);
+		doc_delay(docg3, 2);
+
+		doc_write_page_putbytes(docg3, DOC_LAYOUT_OOB_UNUSED_SZ, oob);
+	}
+	if (oob && !autoecc)
+		doc_write_page_putbytes(docg3, DOC_LAYOUT_OOB_SIZE, oob);
+
+	doc_delay(docg3, 2);
+	doc_page_finish(docg3);
+	doc_delay(docg3, 2);
+	doc_flash_command(docg3, DOC_CMD_PROG_CYCLE2);
+	doc_delay(docg3, 2);
+
+	/*
+	 * The wait status will perform another doc_page_finish() call, but that
+	 * seems to please the docg3, so leave it.
+	 */
+	ret = doc_write_erase_wait_status(docg3);
+	return ret;
+err:
+	doc_read_page_finish(docg3);
+	return ret;
+}
+
+/**
+ * doc_guess_autoecc - Guess autoecc mode from mbd_oob_ops
+ * @ops: the oob operations
+ *
+ * Returns 0 or 1 if success, -EINVAL if invalid oob mode
+ */
+static int doc_guess_autoecc(struct mtd_oob_ops *ops)
+{
+	int autoecc;
+
+	switch (ops->mode) {
+	case MTD_OPS_PLACE_OOB:
+	case MTD_OPS_AUTO_OOB:
+		autoecc = 1;
+		break;
+	case MTD_OPS_RAW:
+		autoecc = 0;
+		break;
+	default:
+		autoecc = -EINVAL;
+	}
+	return autoecc;
+}
+
+/**
+ * doc_fill_autooob - Fill a 16 bytes OOB from 8 non-ECC bytes
+ * @dst: the target 16 bytes OOB buffer
+ * @oobsrc: the source 8 bytes non-ECC OOB buffer
+ *
+ */
+static void doc_fill_autooob(u8 *dst, u8 *oobsrc)
+{
+	memcpy(dst, oobsrc, DOC_LAYOUT_OOB_PAGEINFO_SZ);
+	dst[DOC_LAYOUT_OOB_UNUSED_OFS] = oobsrc[DOC_LAYOUT_OOB_PAGEINFO_SZ];
+}
+
+/**
+ * doc_backup_oob - Backup OOB into docg3 structure
+ * @docg3: the device
+ * @to: the page offset in the chip
+ * @ops: the OOB size and buffer
+ *
+ * As the docg3 should write a page with its OOB in one pass, and some userland
+ * applications do write_oob() to setup the OOB and then write(), store the OOB
+ * into a temporary storage. This is very dangerous, as 2 concurrent
+ * applications could store an OOB, and then write their pages (which will
+ * result into one having its OOB corrupted).
+ *
+ * The only reliable way would be for userland to call doc_write_oob() with both
+ * the page data _and_ the OOB area.
+ *
+ * Returns 0 if success, -EINVAL if ops content invalid
+ */
+static int doc_backup_oob(struct docg3 *docg3, loff_t to,
+			  struct mtd_oob_ops *ops)
+{
+	int ooblen = ops->ooblen, autoecc;
+
+	if (ooblen != DOC_LAYOUT_OOB_SIZE)
+		return -EINVAL;
+	autoecc = doc_guess_autoecc(ops);
+	if (autoecc < 0)
+		return autoecc;
+
+	docg3->oob_write_ofs = to;
+	docg3->oob_autoecc = autoecc;
+	if (ops->mode == MTD_OPS_AUTO_OOB) {
+		doc_fill_autooob(docg3->oob_write_buf, ops->oobbuf);
+		ops->oobretlen = 8;
+	} else {
+		memcpy(docg3->oob_write_buf, ops->oobbuf, DOC_LAYOUT_OOB_SIZE);
+		ops->oobretlen = DOC_LAYOUT_OOB_SIZE;
+	}
+	return 0;
+}
+
+/**
+ * doc_write_oob - Write out of band bytes to flash
+ * @mtd: the device
+ * @ofs: the offset from first block and first page, in bytes, aligned on page
+ *       size
+ * @ops: the mtd oob structure
+ *
+ * Either write OOB data into a temporary buffer, for the subsequent write
+ * page. The provided OOB should be 16 bytes long. If a data buffer is provided
+ * as well, issue the page write.
+ * Or provide data without OOB, and then a all zeroed OOB will be used (ECC will
+ * still be filled in if asked for).
+ *
+ * Returns 0 is successfull, EINVAL if length is not 14 bytes
+ */
+static int doc_write_oob(struct mtd_info *mtd, loff_t ofs,
+			 struct mtd_oob_ops *ops)
+{
+	struct docg3 *docg3 = mtd->priv;
+	int block0, block1, page, ret, pofs = 0, autoecc, oobdelta;
+	u8 *oobbuf = ops->oobbuf;
+	u8 *buf = ops->datbuf;
+	size_t len, ooblen;
+	u8 oob[DOC_LAYOUT_OOB_SIZE];
+
+	if (buf)
+		len = ops->len;
+	else
+		len = 0;
+	if (oobbuf)
+		ooblen = ops->ooblen;
+	else
+		ooblen = 0;
+
+	if (oobbuf && ops->mode == MTD_OPS_PLACE_OOB)
+		oobbuf += ops->ooboffs;
+
+	doc_dbg("doc_write_oob(from=%lld, mode=%d, data=(%p:%zu), oob=(%p:%zu))\n",
+		ofs, ops->mode, buf, len, oobbuf, ooblen);
+	switch (ops->mode) {
+	case MTD_OPS_PLACE_OOB:
+	case MTD_OPS_RAW:
+		oobdelta = mtd->oobsize;
+		break;
+	case MTD_OPS_AUTO_OOB:
+		oobdelta = mtd->ecclayout->oobavail;
+		break;
+	default:
+		oobdelta = 0;
+	}
+	if ((len % DOC_LAYOUT_PAGE_SIZE) || (ooblen % oobdelta) ||
+	    (ofs % DOC_LAYOUT_PAGE_SIZE))
+		return -EINVAL;
+	if (len && ooblen &&
+	    (len / DOC_LAYOUT_PAGE_SIZE) != (ooblen / oobdelta))
+		return -EINVAL;
+
+	ret = -EINVAL;
+	calc_block_sector(ofs + len, &block0, &block1, &page, &pofs);
+	if (block1 > docg3->max_block)
+		goto err;
+
+	ops->oobretlen = 0;
+	ops->retlen = 0;
+	ret = 0;
+	if (len == 0 && ooblen == 0)
+		return -EINVAL;
+	if (len == 0 && ooblen > 0)
+		return doc_backup_oob(docg3, ofs, ops);
+
+	autoecc = doc_guess_autoecc(ops);
+	if (autoecc < 0)
+		return autoecc;
+
+	while (!ret && len > 0) {
+		memset(oob, 0, sizeof(oob));
+		if (ofs == docg3->oob_write_ofs)
+			memcpy(oob, docg3->oob_write_buf, DOC_LAYOUT_OOB_SIZE);
+		else if (ooblen > 0 && ops->mode == MTD_OPS_AUTO_OOB)
+			doc_fill_autooob(oob, oobbuf);
+		else if (ooblen > 0)
+			memcpy(oob, oobbuf, DOC_LAYOUT_OOB_SIZE);
+		ret = doc_write_page(docg3, ofs, buf, oob, autoecc);
+
+		ofs += DOC_LAYOUT_PAGE_SIZE;
+		len -= DOC_LAYOUT_PAGE_SIZE;
+		buf += DOC_LAYOUT_PAGE_SIZE;
+		if (ooblen) {
+			oobbuf += oobdelta;
+			ooblen -= oobdelta;
+			ops->oobretlen += oobdelta;
+		}
+		ops->retlen += DOC_LAYOUT_PAGE_SIZE;
+	}
+err:
+	doc_set_device_id(docg3, 0);
+	return ret;
+}
+
+/**
+ * doc_write - Write a buffer to the chip
+ * @mtd: the device
+ * @to: the offset from first block and first page, in bytes, aligned on page
+ *      size
+ * @len: the number of bytes to write (must be a full page size, ie. 512)
+ * @retlen: the number of bytes actually written (0 or 512)
+ * @buf: the buffer to get bytes from
+ *
+ * Writes data to the chip.
+ *
+ * Returns 0 if write successful, -EIO if write error
+ */
+static int doc_write(struct mtd_info *mtd, loff_t to, size_t len,
+		     size_t *retlen, const u_char *buf)
+{
+	struct docg3 *docg3 = mtd->priv;
+	int ret;
+	struct mtd_oob_ops ops;
+
+	doc_dbg("doc_write(to=%lld, len=%zu)\n", to, len);
+	ops.datbuf = (char *)buf;
+	ops.len = len;
+	ops.mode = MTD_OPS_PLACE_OOB;
+	ops.oobbuf = NULL;
+	ops.ooblen = 0;
+	ops.ooboffs = 0;
+
+	ret = doc_write_oob(mtd, to, &ops);
+	*retlen = ops.retlen;
+	return ret;
+}
+
 /*
  * Debug sysfs entries
  */
@@ -1052,6 +1580,7 @@ static struct mtd_info *doc_probe_device(void __iomem *base, int floor,
 
 	doc_set_driver_info(chip_id, mtd);
 
+	doc_hamming_ecc_init(docg3, DOC_LAYOUT_OOB_PAGEINFO_SZ);
 	doc_reload_bbt(docg3);
 	return mtd;