diff options
Diffstat (limited to 'drivers/mtd/maps/Kconfig')
| -rw-r--r-- | drivers/mtd/maps/Kconfig | 73 |
1 files changed, 28 insertions, 45 deletions
diff --git a/drivers/mtd/maps/Kconfig b/drivers/mtd/maps/Kconfig index 24747bdc3e1..f457315579d 100644 --- a/drivers/mtd/maps/Kconfig +++ b/drivers/mtd/maps/Kconfig @@ -60,6 +60,15 @@ config MTD_PHYSMAP_BANKWIDTH Ignore this option if you use run-time physmap configuration (i.e., run-time calling physmap_configure()). +config MTD_PHYSMAP_OF + tristate "Flash device in physical memory map based on OF descirption" + depends on PPC_OF && (MTD_CFI || MTD_JEDECPROBE || MTD_ROM) + help + This provides a 'mapping' driver which allows the NOR Flash and + ROM driver code to communicate with chips which are mapped + physically into the CPU's memory. The mapping description here is + taken from OF device tree. + config MTD_SUN_UFLASH tristate "Sun Microsystems userflash support" depends on SPARC && MTD_CFI @@ -184,6 +193,24 @@ config MTD_ICHXROM BE VERY CAREFUL. +config MTD_ESB2ROM + tristate "BIOS flash chip on Intel ESB Controller Hub 2" + depends on X86 && MTD_JEDECPROBE && PCI + help + Support for treating the BIOS flash chip on ESB2 motherboards + as an MTD device - with this you can reprogram your BIOS. + + BE VERY CAREFUL. + +config MTD_CK804XROM + tristate "BIOS flash chip on Nvidia CK804" + depends on X86 && MTD_JEDECPROBE + help + Support for treating the BIOS flash chip on nvidia motherboards + as an MTD device - with this you can reprogram your BIOS. + + BE VERY CAREFUL. + config MTD_SCB2_FLASH tristate "BIOS flash chip on Intel SCB2 boards" depends on X86 && MTD_JEDECPROBE @@ -355,50 +382,6 @@ config MTD_TQM834x TQ Components TQM834x boards. If you have one of these boards and would like to use the flash chips on it, say 'Y'. -config MTD_CSTM_MIPS_IXX - tristate "Flash chip mapping on ITE QED-4N-S01B, Globespan IVR or custom board" - depends on MIPS && MTD_CFI && MTD_JEDECPROBE && MTD_PARTITIONS - help - This provides a mapping driver for the Integrated Technology - Express, Inc (ITE) QED-4N-S01B eval board and the Globespan IVR - Reference Board. It provides the necessary addressing, length, - buswidth, vpp code and addition setup of the flash device for - these boards. In addition, this mapping driver can be used for - other boards via setting of the CONFIG_MTD_CSTM_MIPS_IXX_START/ - LEN/BUSWIDTH parameters. This mapping will provide one mtd device - using one partition. The start address can be offset from the - beginning of flash and the len can be less than the total flash - device size to allow a window into the flash. Both CFI and JEDEC - probes are called. - -config MTD_CSTM_MIPS_IXX_START - hex "Physical start address of flash mapping" - depends on MTD_CSTM_MIPS_IXX - default "0x8000000" - help - This is the physical memory location that the MTD driver will - use for the flash chips on your particular target board. - Refer to the memory map which should hopefully be in the - documentation for your board. - -config MTD_CSTM_MIPS_IXX_LEN - hex "Physical length of flash mapping" - depends on MTD_CSTM_MIPS_IXX - default "0x4000000" - help - This is the total length that the MTD driver will use for the - flash chips on your particular board. Refer to the memory - map which should hopefully be in the documentation for your - board. - -config MTD_CSTM_MIPS_IXX_BUSWIDTH - int "Bus width in octets" - depends on MTD_CSTM_MIPS_IXX - default "2" - help - This is the total bus width of the mapping of the flash chips - on your particular board. - config MTD_OCELOT tristate "Momenco Ocelot boot flash device" depends on MIPS && MOMENCO_OCELOT @@ -607,7 +590,7 @@ config MTD_BAST_MAXSIZE default "4" config MTD_SHARP_SL - bool "ROM maped on Sharp SL Series" + bool "ROM mapped on Sharp SL Series" depends on MTD && ARCH_PXA help This enables access to the flash chip on the Sharp SL Series of PDAs. |