diff options
Diffstat (limited to 'drivers/mtd/nand/Kconfig')
| -rw-r--r-- | drivers/mtd/nand/Kconfig | 52 |
1 files changed, 9 insertions, 43 deletions
diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig index 50543f16621..93ae6a6d94f 100644 --- a/drivers/mtd/nand/Kconfig +++ b/drivers/mtd/nand/Kconfig @@ -43,6 +43,7 @@ config MTD_SM_COMMON config MTD_NAND_DENALI tristate "Support Denali NAND controller" + depends on HAS_DMA help Enable support for the Denali NAND controller. This should be combined with either the PCI or platform drivers to provide device @@ -75,7 +76,7 @@ config MTD_NAND_DENALI_SCRATCH_REG_ADDR config MTD_NAND_GPIO tristate "GPIO NAND Flash driver" - depends on GPIOLIB && ARM + depends on GPIOLIB help This enables a GPIO based NAND flash driver. @@ -95,43 +96,15 @@ config MTD_NAND_OMAP2 config MTD_NAND_OMAP_BCH depends on MTD_NAND && MTD_NAND_OMAP2 && ARCH_OMAP3 - tristate "Enable support for hardware BCH error correction" + tristate "Support hardware based BCH error correction" default n select BCH - select BCH_CONST_PARAMS help - Support for hardware BCH error correction. - -choice - prompt "BCH error correction capability" - depends on MTD_NAND_OMAP_BCH - -config MTD_NAND_OMAP_BCH8 - bool "8 bits / 512 bytes (recommended)" - help - Support correcting up to 8 bitflips per 512-byte block. - This will use 13 bytes of spare area per 512 bytes of page data. - This is the recommended mode, as 4-bit mode does not work - on some OMAP3 revisions, due to a hardware bug. - -config MTD_NAND_OMAP_BCH4 - bool "4 bits / 512 bytes" - help - Support correcting up to 4 bitflips per 512-byte block. - This will use 7 bytes of spare area per 512 bytes of page data. - Note that this mode does not work on some OMAP3 revisions, due to a - hardware bug. Please check your OMAP datasheet before selecting this - mode. - -endchoice - -if MTD_NAND_OMAP_BCH -config BCH_CONST_M - default 13 -config BCH_CONST_T - default 4 if MTD_NAND_OMAP_BCH4 - default 8 if MTD_NAND_OMAP_BCH8 -endif + This config enables the ELM hardware engine, which can be used to + locate and correct errors when using BCH ECC scheme. This offloads + the cpu from doing ECC error searching and correction. However some + legacy OMAP families like OMAP2xxx, OMAP3xxx do not have ELM engine + so they should not enable this config symbol. config MTD_NAND_IDS tristate @@ -354,7 +327,7 @@ config MTD_NAND_ATMEL config MTD_NAND_PXA3xx tristate "Support for NAND flash devices on PXA3xx" - depends on PXA3xx || ARCH_MMP + depends on PXA3xx || ARCH_MMP || PLAT_ORION help This enables the driver for the NAND flash device found on PXA3xx processors @@ -432,13 +405,6 @@ config MTD_NAND_PLATFORM devices. You will need to provide platform-specific functions via platform_data. -config MTD_ALAUDA - tristate "MTD driver for Olympus MAUSB-10 and Fujifilm DPC-R1" - depends on USB - help - These two (and possibly other) Alauda-based cardreaders for - SmartMedia and xD allow raw flash access. - config MTD_NAND_ORION tristate "NAND Flash support for Marvell Orion SoC" depends on PLAT_ORION |