diff options
Diffstat (limited to 'drivers/net/Kconfig')
| -rw-r--r-- | drivers/net/Kconfig | 307 |
1 files changed, 132 insertions, 175 deletions
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index f4182cfffe9..1d8af334833 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -26,14 +26,6 @@ menuconfig NETDEVICES # that for each of the symbols. if NETDEVICES -config NETDEVICES_MULTIQUEUE - bool "Netdevice multiple hardware queue support" - ---help--- - Say Y here if you want to allow the network stack to use multiple - hardware TX queues on an ethernet device. - - Most people will say N here. - config IFB tristate "Intermediate Functional Block support" depends on NET_CLS_ACT @@ -217,7 +209,7 @@ config MII config MACB tristate "Atmel MACB support" - depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91CAP9 + depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91SAM9G20 || ARCH_AT91CAP9 select PHYLIB help The Atmel MACB ethernet interface is found on many AT32 and AT91 @@ -333,15 +325,6 @@ config APNE To compile this driver as a module, choose M here: the module will be called apne. -config APOLLO_ELPLUS - tristate "Apollo 3c505 support" - depends on APOLLO - help - Say Y or M here if your Apollo has a 3Com 3c505 ISA Ethernet card. - If you don't have one made for Apollos, you can use one from a PC, - except that your Apollo won't be able to boot from it (because the - code in the ROM will be for a PC). - config MAC8390 bool "Macintosh NS 8390 based ethernet cards" depends on MAC @@ -524,6 +507,19 @@ config STNIC If unsure, say N. +config SH_ETH + tristate "Renesas SuperH Ethernet support" + depends on SUPERH && \ + (CPU_SUBTYPE_SH7710 || CPU_SUBTYPE_SH7712 || CPU_SUBTYPE_SH7763 || \ + CPU_SUBTYPE_SH7619) + select CRC32 + select MII + select MDIO_BITBANG + select PHYLIB + help + Renesas SuperH Ethernet device driver. + This driver support SH7710, SH7712, SH7763 and SH7619. + config SUNLANCE tristate "Sun LANCE support" depends on SBUS @@ -826,14 +822,14 @@ config ULTRA32 will be called smc-ultra32. config BFIN_MAC - tristate "Blackfin 527/536/537 on-chip mac support" - depends on NET_ETHERNET && (BF527 || BF537 || BF536) + tristate "Blackfin on-chip MAC support" + depends on NET_ETHERNET && (BF526 || BF527 || BF536 || BF537) select CRC32 select MII select PHYLIB select BFIN_MAC_USE_L1 if DMA_UNCACHED_NONE help - This is the driver for blackfin on-chip mac device. Say Y if you want it + This is the driver for Blackfin on-chip mac device. Say Y if you want it compiled into the kernel. This driver is also available as a module ( = code which can be inserted in and removed from the running kernel whenever you want). The module will be called bfin_mac. @@ -926,6 +922,23 @@ config DM9000 To compile this driver as a module, choose M here. The module will be called dm9000. +config DM9000_DEBUGLEVEL + int "DM9000 maximum debug level" + depends on DM9000 + default 4 + help + The maximum level of debugging code compiled into the DM9000 + driver. + +config DM9000_FORCE_SIMPLE_PHY_POLL + bool "Force simple NSR based PHY polling" + depends on DM9000 + ---help--- + This configuration forces the DM9000 to use the NSR's LinkStatus + bit to determine if the link is up or down instead of the more + costly MII PHY reads. Note, this will not work if the chip is + operating with an external PHY. + config ENC28J60 tristate "ENC28J60 support" depends on EXPERIMENTAL && SPI && NET_ETHERNET @@ -943,19 +956,11 @@ config ENC28J60_WRITEVERIFY Enable the verify after the buffer write useful for debugging purpose. If unsure, say N. -config DM9000_DEBUGLEVEL - int "DM9000 maximum debug level" - depends on DM9000 - default 4 - help - The maximum level of debugging code compiled into the DM9000 - driver. - config SMC911X tristate "SMSC LAN911[5678] support" select CRC32 select MII - depends on ARCH_PXA || SH_MAGIC_PANEL_R2 + depends on ARCH_PXA || SUPERH help This is a driver for SMSC's LAN911x series of Ethernet chipsets including the new LAN9115, LAN9116, LAN9117, and LAN9118. @@ -1167,7 +1172,7 @@ config ETH16I config NE2000 tristate "NE2000/NE1000 support" - depends on NET_ISA || (Q40 && m) || M32R || TOSHIBA_RBTX4927 || TOSHIBA_RBTX4938 + depends on NET_ISA || (Q40 && m) || M32R || MACH_TX49XX select CRC32 ---help--- If you have a network (Ethernet) card of this type, say Y and read @@ -1243,7 +1248,6 @@ config IBMVETH To compile this driver as a module, choose M here. The module will be called ibmveth. -source "drivers/net/ibm_emac/Kconfig" source "drivers/net/ibm_newemac/Kconfig" config NET_PCI @@ -1286,20 +1290,6 @@ config AMD8111_ETH To compile this driver as a module, choose M here. The module will be called amd8111e. -config AMD8111E_NAPI - bool "Use RX polling (NAPI)" - depends on AMD8111_ETH - help - NAPI is a new driver API designed to reduce CPU and interrupt load - when the driver is receiving lots of packets from the card. It is - still somewhat experimental and thus not yet enabled by default. - - If your estimated Rx load is 10kpps or more, or if the card will be - deployed on potentially unfriendly networks (e.g. in a firewall), - then say Y here. - - If in doubt, say N. - config ADAPTEC_STARFIRE tristate "Adaptec Starfire/DuraLAN support" depends on NET_PCI && PCI @@ -1314,20 +1304,6 @@ config ADAPTEC_STARFIRE To compile this driver as a module, choose M here: the module will be called starfire. This is recommended. -config ADAPTEC_STARFIRE_NAPI - bool "Use Rx Polling (NAPI) (EXPERIMENTAL)" - depends on ADAPTEC_STARFIRE && EXPERIMENTAL - help - NAPI is a new driver API designed to reduce CPU and interrupt load - when the driver is receiving lots of packets from the card. It is - still somewhat experimental and thus not yet enabled by default. - - If your estimated Rx load is 10kpps or more, or if the card will be - deployed on potentially unfriendly networks (e.g. in a firewall), - then say Y here. - - If in doubt, say N. - config AC3200 tristate "Ansel Communications EISA 3200 support (EXPERIMENTAL)" depends on NET_PCI && (ISA || EISA) && EXPERIMENTAL @@ -1410,7 +1386,8 @@ config FORCEDETH_NAPI config CS89x0 tristate "CS89x0 support" - depends on NET_PCI && (ISA || MACH_IXDP2351 || ARCH_IXDP2X01 || ARCH_PNX010X) + depends on NET_ETHERNET && (ISA || EISA || MACH_IXDP2351 \ + || ARCH_IXDP2X01 || ARCH_PNX010X || MACH_MX31ADS) ---help--- Support for CS89x0 chipset based Ethernet cards. If you have a network (Ethernet) card of this type, say Y and read the @@ -1421,6 +1398,11 @@ config CS89x0 To compile this driver as a module, choose M here. The module will be called cs89x0. +config CS89x0_NONISA_IRQ + def_bool y + depends on CS89x0 != n + depends on MACH_IXDP2351 || ARCH_IXDP2X01 || ARCH_PNX010X || MACH_MX31ADS + config TC35815 tristate "TOSHIBA TC35815 Ethernet support" depends on NET_PCI && PCI && MIPS @@ -1670,7 +1652,7 @@ config SUNDANCE_MMIO config TLAN tristate "TI ThunderLAN support" - depends on NET_PCI && (PCI || EISA) && !64BIT + depends on NET_PCI && (PCI || EISA) ---help--- If you have a PCI Ethernet network card based on the ThunderLAN chip which is supported by this driver, say Y and read the @@ -1710,26 +1692,6 @@ config VIA_RHINE_MMIO If unsure, say Y. -config VIA_RHINE_NAPI - bool "Use Rx Polling (NAPI)" - depends on VIA_RHINE - help - NAPI is a new driver API designed to reduce CPU and interrupt load - when the driver is receiving lots of packets from the card. - - If your estimated Rx load is 10kpps or more, or if the card will be - deployed on potentially unfriendly networks (e.g. in a firewall), - then say Y here. - -config LAN_SAA9730 - bool "Philips SAA9730 Ethernet support" - depends on NET_PCI && PCI && MIPS_ATLAS - help - The SAA9730 is a combined multimedia and peripheral controller used - in thin clients, Internet access terminals, and diskless - workstations. - See <http://www.semiconductors.philips.com/pip/SAA9730_flyer_1>. - config SC92031 tristate "Silan SC92031 PCI Fast Ethernet Adapter driver (EXPERIMENTAL)" depends on NET_PCI && PCI && EXPERIMENTAL @@ -1857,7 +1819,7 @@ config FEC2 config FEC_MPC52xx tristate "MPC52xx FEC driver" - depends on PPC_MERGE && PPC_MPC52xx && PPC_BESTCOMM_FEC + depends on PPC_MPC52xx && PPC_BESTCOMM_FEC select CRC32 select PHYLIB ---help--- @@ -1884,7 +1846,17 @@ config NE_H8300 Say Y here if you want to use the NE2000 compatible controller on the Renesas H8/300 processor. -source "drivers/net/fec_8xx/Kconfig" +config ATL2 + tristate "Atheros L2 Fast Ethernet support" + depends on PCI + select CRC32 + select MII + help + This driver supports the Atheros L2 fast ethernet adapter. + + To compile this driver as a module, choose M here. The module + will be called atl2. + source "drivers/net/fs_enet/Kconfig" endif # NET_ETHERNET @@ -1972,29 +1944,6 @@ config E1000 To compile this driver as a module, choose M here. The module will be called e1000. -config E1000_NAPI - bool "Use Rx Polling (NAPI)" - depends on E1000 - help - NAPI is a new driver API designed to reduce CPU and interrupt load - when the driver is receiving lots of packets from the card. It is - still somewhat experimental and thus not yet enabled by default. - - If your estimated Rx load is 10kpps or more, or if the card will be - deployed on potentially unfriendly networks (e.g. in a firewall), - then say Y here. - - If in doubt, say N. - -config E1000_DISABLE_PACKET_SPLIT - bool "Disable Packet Split for PCI express adapters" - depends on E1000 - help - Say Y here if you want to use the legacy receive path for PCI express - hardware. - - If in doubt, say N. - config E1000E tristate "Intel(R) PRO/1000 PCI-Express Gigabit Ethernet support" depends on PCI && (!SPARC32 || BROKEN) @@ -2014,9 +1963,6 @@ config E1000E To compile this driver as a module, choose M here. The module will be called e1000e. -config E1000E_ENABLED - def_bool E1000E != n - config IP1000 tristate "IP1000 Gigabit Ethernet support" depends on PCI && EXPERIMENTAL @@ -2048,6 +1994,15 @@ config IGB To compile this driver as a module, choose M here. The module will be called igb. +config IGB_LRO + bool "Use software LRO" + depends on IGB && INET + select INET_LRO + ---help--- + Say Y here if you want to use large receive offload. + + If in doubt, say N. + source "drivers/net/ixp2000/Kconfig" config MYRI_SBUS @@ -2099,33 +2054,20 @@ config R8169 tristate "Realtek 8169 gigabit ethernet support" depends on PCI select CRC32 + select MII ---help--- Say Y here if you have a Realtek 8169 PCI Gigabit Ethernet adapter. To compile this driver as a module, choose M here: the module will be called r8169. This is recommended. -config R8169_NAPI - bool "Use Rx Polling (NAPI) (EXPERIMENTAL)" - depends on R8169 && EXPERIMENTAL - help - NAPI is a new driver API designed to reduce CPU and interrupt load - when the driver is receiving lots of packets from the card. It is - still somewhat experimental and thus not yet enabled by default. - - If your estimated Rx load is 10kpps or more, or if the card will be - deployed on potentially unfriendly networks (e.g. in a firewall), - then say Y here. - - If in doubt, say N. - config R8169_VLAN bool "VLAN support" depends on R8169 && VLAN_8021Q ---help--- Say Y here for the r8169 driver to support the functions required by the kernel 802.1Q code. - + If in doubt, say Y. config SB1250_MAC @@ -2228,6 +2170,7 @@ config VIA_VELOCITY config TIGON3 tristate "Broadcom Tigon3 support" depends on PCI + select PHYLIB help This driver supports Broadcom Tigon3 based gigabit Ethernet cards. @@ -2283,6 +2226,19 @@ config GELIC_WIRELESS the driver automatically distinguishes the models, you can safely enable this option even if you have a wireless-less model. +config GELIC_WIRELESS_OLD_PSK_INTERFACE + bool "PS3 Wireless private PSK interface (OBSOLETE)" + depends on GELIC_WIRELESS + help + This option retains the obsolete private interface to pass + the PSK from user space programs to the driver. The PSK + stands for 'Pre Shared Key' and is used for WPA[2]-PSK + (WPA-Personal) environment. + If WPA[2]-PSK is used and you need to use old programs that + support only this old interface, say Y. Otherwise N. + + If unsure, say N. + config GIANFAR tristate "Gianfar Ethernet" depends on FSL_SOC @@ -2292,10 +2248,6 @@ config GIANFAR This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx, and MPC86xx family of chips, and the FEC on the 8540. -config GFAR_NAPI - bool "Use Rx Polling (NAPI)" - depends on GIANFAR - config UCC_GETH tristate "Freescale QE Gigabit Ethernet" depends on QUICC_ENGINE @@ -2304,10 +2256,6 @@ config UCC_GETH This driver supports the Gigabit Ethernet mode of the QUICC Engine, which is available on some Freescale SOCs. -config UGETH_NAPI - bool "Use Rx Polling (NAPI)" - depends on UCC_GETH - config UGETH_MAGIC_PACKET bool "Magic Packet detection support" depends on UCC_GETH @@ -2323,7 +2271,7 @@ config UGETH_TX_ON_DEMAND config MV643XX_ETH tristate "Marvell Discovery (643XX) and Orion ethernet support" depends on MV64360 || MV64X60 || (PPC_MULTIPLATFORM && PPC32) || PLAT_ORION - select MII + select PHYLIB help This driver supports the gigabit ethernet MACs in the Marvell Discovery PPC/MIPS chipset family (MV643XX) and @@ -2342,16 +2290,40 @@ config QLA3XXX will be called qla3xxx. config ATL1 - tristate "Attansic L1 Gigabit Ethernet support (EXPERIMENTAL)" - depends on PCI && EXPERIMENTAL + tristate "Atheros/Attansic L1 Gigabit Ethernet support" + depends on PCI select CRC32 select MII help - This driver supports the Attansic L1 gigabit ethernet adapter. + This driver supports the Atheros/Attansic L1 gigabit ethernet + adapter. To compile this driver as a module, choose M here. The module will be called atl1. +config ATL1E + tristate "Atheros L1E Gigabit Ethernet support (EXPERIMENTAL)" + depends on PCI && EXPERIMENTAL + select CRC32 + select MII + help + This driver supports the Atheros L1E gigabit ethernet adapter. + + To compile this driver as a module, choose M here. The module + will be called atl1e. + +config JME + tristate "JMicron(R) PCI-Express Gigabit Ethernet support" + depends on PCI + select CRC32 + select MII + ---help--- + This driver supports the PCI-Express gigabit ethernet adapters + based on JMicron JMC250 chipset. + + To compile this driver as a module, choose M here. The module + will be called jme. + endif # NETDEV_1000 # @@ -2397,18 +2369,11 @@ config CHELSIO_T1_1G Enables support for Chelsio's gigabit Ethernet PCI cards. If you are using only 10G cards say 'N' here. -config CHELSIO_T1_NAPI - bool "Use Rx Polling (NAPI)" - depends on CHELSIO_T1 - default y - help - NAPI is a driver API designed to reduce CPU and interrupt load - when the driver is receiving lots of packets from the card. - config CHELSIO_T3 tristate "Chelsio Communications T3 10Gb Ethernet support" - depends on PCI + depends on PCI && INET select FW_LOADER + select INET_LRO help This driver supports Chelsio T3-based gigabit and 10Gb Ethernet adapters. @@ -2434,9 +2399,18 @@ config EHEA To compile the driver as a module, choose M here. The module will be called ehea. +config ENIC + tristate "Cisco 10G Ethernet NIC support" + depends on PCI && INET + select INET_LRO + help + This enables the support for the Cisco 10G Ethernet card. + config IXGBE tristate "Intel(R) 10GbE PCI Express adapters support" - depends on PCI + depends on PCI && INET + select INET_LRO + select INTEL_IOATDMA ---help--- This driver supports Intel(R) 10GbE PCI Express family of adapters. For more information on how to identify your adapter, go @@ -2474,20 +2448,6 @@ config IXGB To compile this driver as a module, choose M here. The module will be called ixgb. -config IXGB_NAPI - bool "Use Rx Polling (NAPI) (EXPERIMENTAL)" - depends on IXGB && EXPERIMENTAL - help - NAPI is a new driver API designed to reduce CPU and interrupt load - when the driver is receiving lots of packets from the card. It is - still somewhat experimental and thus not yet enabled by default. - - If your estimated Rx load is 10kpps or more, or if the card will be - deployed on potentially unfriendly networks (e.g. in a firewall), - then say Y here. - - If in doubt, say N. - config S2IO tristate "S2IO 10Gbe XFrame NIC" depends on PCI @@ -2496,26 +2456,13 @@ config S2IO More specific information on configuring the driver is in <file:Documentation/networking/s2io.txt>. -config S2IO_NAPI - bool "Use Rx Polling (NAPI) (EXPERIMENTAL)" - depends on S2IO && EXPERIMENTAL - help - NAPI is a new driver API designed to reduce CPU and interrupt load - when the driver is receiving lots of packets from the card. It is - still somewhat experimental and thus not yet enabled by default. - - If your estimated Rx load is 10kpps or more, or if the card will be - deployed on potentially unfriendly networks (e.g. in a firewall), - then say Y here. - - If in doubt, say N. - config MYRI10GE tristate "Myricom Myri-10G Ethernet support" depends on PCI && INET select FW_LOADER select CRC32 select INET_LRO + select INTEL_IOATDMA ---help--- This driver supports Myricom Myri-10G Dual Protocol interface in Ethernet mode. If the eeprom on your board is not recent enough, @@ -2574,11 +2521,21 @@ config BNX2X tristate "Broadcom NetXtremeII 10Gb support" depends on PCI select ZLIB_INFLATE + select LIBCRC32C help This driver supports Broadcom NetXtremeII 10 gigabit Ethernet cards. To compile this driver as a module, choose M here: the module will be called bnx2x. This is recommended. +config QLGE + tristate "QLogic QLGE 10Gb Ethernet Driver Support" + depends on PCI + help + This driver supports QLogic ISP8XXX 10Gb Ethernet cards. + + To compile this driver as a module, choose M here: the module + will be called qlge. + source "drivers/net/sfc/Kconfig" endif # NETDEV_10000 |