diff options
Diffstat (limited to 'drivers/net/Kconfig')
| -rw-r--r-- | drivers/net/Kconfig | 72 |
1 files changed, 2 insertions, 70 deletions
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index ef6b6bee11d..7bdc22b5985 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -195,6 +195,8 @@ config SUNGEM_PHY source "drivers/net/ethernet/Kconfig" +source "drivers/net/fddi/Kconfig" + source "drivers/net/tokenring/Kconfig" source "drivers/net/wireless/Kconfig" @@ -268,76 +270,6 @@ config RIONET_RX_SIZE depends on RIONET default "128" -config FDDI - tristate "FDDI driver support" - depends on (PCI || EISA || TC) - help - Fiber Distributed Data Interface is a high speed local area network - design; essentially a replacement for high speed Ethernet. FDDI can - run over copper or fiber. If you are connected to such a network and - want a driver for the FDDI card in your computer, say Y here (and - then also Y to the driver for your FDDI card, below). Most people - will say N. - -config DEFXX - tristate "Digital DEFTA/DEFEA/DEFPA adapter support" - depends on FDDI && (PCI || EISA || TC) - ---help--- - This is support for the DIGITAL series of TURBOchannel (DEFTA), - EISA (DEFEA) and PCI (DEFPA) controllers which can connect you - to a local FDDI network. - - To compile this driver as a module, choose M here: the module - will be called defxx. If unsure, say N. - -config DEFXX_MMIO - bool - prompt "Use MMIO instead of PIO" if PCI || EISA - depends on DEFXX - default n if PCI || EISA - default y - ---help--- - This instructs the driver to use EISA or PCI memory-mapped I/O - (MMIO) as appropriate instead of programmed I/O ports (PIO). - Enabling this gives an improvement in processing time in parts - of the driver, but it may cause problems with EISA (DEFEA) - adapters. TURBOchannel does not have the concept of I/O ports, - so MMIO is always used for these (DEFTA) adapters. - - If unsure, say N. - -config SKFP - tristate "SysKonnect FDDI PCI support" - depends on FDDI && PCI - select BITREVERSE - ---help--- - Say Y here if you have a SysKonnect FDDI PCI adapter. - The following adapters are supported by this driver: - - SK-5521 (SK-NET FDDI-UP) - - SK-5522 (SK-NET FDDI-UP DAS) - - SK-5541 (SK-NET FDDI-FP) - - SK-5543 (SK-NET FDDI-LP) - - SK-5544 (SK-NET FDDI-LP DAS) - - SK-5821 (SK-NET FDDI-UP64) - - SK-5822 (SK-NET FDDI-UP64 DAS) - - SK-5841 (SK-NET FDDI-FP64) - - SK-5843 (SK-NET FDDI-LP64) - - SK-5844 (SK-NET FDDI-LP64 DAS) - - Netelligent 100 FDDI DAS Fibre SC - - Netelligent 100 FDDI SAS Fibre SC - - Netelligent 100 FDDI DAS UTP - - Netelligent 100 FDDI SAS UTP - - Netelligent 100 FDDI SAS Fibre MIC - - Read <file:Documentation/networking/skfp.txt> for information about - the driver. - - Questions concerning this driver can be addressed to: - <linux@syskonnect.de> - - To compile this driver as a module, choose M here: the module - will be called skfp. This is recommended. - config HIPPI bool "HIPPI driver support (EXPERIMENTAL)" depends on EXPERIMENTAL && INET && PCI |