diff options
Diffstat (limited to 'drivers/net/Kconfig')
| -rw-r--r-- | drivers/net/Kconfig | 19 |
1 files changed, 10 insertions, 9 deletions
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index e45a8f95971..11ca9f03b43 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -66,7 +66,7 @@ config BONDING 'Trunking' by Sun, 802.3ad by the IEEE, and 'Bonding' in Linux. The driver supports multiple bonding modes to allow for both high - perfomance and high availability operation. + performance and high availability operation. Refer to <file:Documentation/networking/bonding.txt> for more information. @@ -698,8 +698,8 @@ config VORTEX depends on NET_VENDOR_3COM && (PCI || EISA) select MII ---help--- - This option enables driver support for a large number of 10mbps and - 10/100mbps EISA, PCI and PCMCIA 3Com network cards: + This option enables driver support for a large number of 10Mbps and + 10/100Mbps EISA, PCI and PCMCIA 3Com network cards: "Vortex" (Fast EtherLink 3c590/3c592/3c595/3c597) EISA and PCI "Boomerang" (EtherLink XL 3c900 or 3c905) PCI @@ -1021,7 +1021,7 @@ config EEXPRESS_PRO depends on NET_ISA ---help--- If you have a network (Ethernet) card of this type, say Y. This - driver supports intel i82595{FX,TX} based boards. Note however + driver supports Intel i82595{FX,TX} based boards. Note however that the EtherExpress PRO/100 Ethernet card has its own separate driver. Please read the Ethernet-HOWTO, available from <http://www.tldp.org/docs.html#howto>. @@ -1207,7 +1207,7 @@ config IBM_EMAC_RX_SKB_HEADROOM help Additional receive skb headroom. Note, that driver will always reserve at least 2 bytes to make IP header - aligned, so usualy there is no need to add any additional + aligned, so usually there is no need to add any additional headroom. If unsure, set to 0. @@ -1933,7 +1933,7 @@ config MYRI_SBUS will be called myri_sbus. This is recommended. config NS83820 - tristate "National Semiconduct DP83820 support" + tristate "National Semiconductor DP83820 support" depends on PCI help This is a driver for the National Semiconductor DP83820 series @@ -2194,6 +2194,7 @@ config GFAR_NAPI config MV643XX_ETH tristate "MV-643XX Ethernet support" depends on MOMENCO_OCELOT_C || MOMENCO_JAGUAR_ATX || MV64360 || MOMENCO_OCELOT_3 || PPC_MULTIPLATFORM + select MII help This driver supports the gigabit Ethernet on the Marvell MV643XX chipset which is used in the Momenco Ocelot C and Jaguar ATX and @@ -2513,7 +2514,7 @@ config PPP_FILTER Say Y here if you want to be able to filter the packets passing over PPP interfaces. This allows you to control which packets count as activity (i.e. which packets will reset the idle timer or bring up - a demand-dialled link) and which packets are to be dropped entirely. + a demand-dialed link) and which packets are to be dropped entirely. You need to say Y here if you wish to use the pass-filter and active-filter options to pppd. @@ -2701,8 +2702,8 @@ config SHAPER <file:Documentation/networking/shaper.txt> for more information. An alternative to this traffic shaper is the experimental - Class-Based Queueing (CBQ) scheduling support which you get if you - say Y to "QoS and/or fair queueing" above. + Class-Based Queuing (CBQ) scheduling support which you get if you + say Y to "QoS and/or fair queuing" above. To compile this driver as a module, choose M here: the module will be called shaper. If unsure, say N. |