diff options
Diffstat (limited to 'drivers/net/Kconfig')
| -rw-r--r-- | drivers/net/Kconfig | 106 |
1 files changed, 0 insertions, 106 deletions
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index 8da9f962068..42408d7dc1c 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -594,73 +594,6 @@ config FEALNX Say Y here to support the Myson MTD-800 family of PCI-based Ethernet cards. <http://www.myson.com.tw/> -config 8139CP - tristate "RealTek RTL-8139 C+ PCI Fast Ethernet Adapter support (EXPERIMENTAL)" - depends on NET_PCI && PCI && EXPERIMENTAL - select CRC32 - select MII - help - This is a driver for the Fast Ethernet PCI network cards based on - the RTL8139C+ chips. If you have one of those, say Y and read - the Ethernet-HOWTO, available from - <http://www.tldp.org/docs.html#howto>. - - To compile this driver as a module, choose M here: the module - will be called 8139cp. This is recommended. - -config 8139TOO - tristate "RealTek RTL-8129/8130/8139 PCI Fast Ethernet Adapter support" - depends on NET_PCI && PCI - select CRC32 - select MII - ---help--- - This is a driver for the Fast Ethernet PCI network cards based on - the RTL 8129/8130/8139 chips. If you have one of those, say Y and - read the Ethernet-HOWTO <http://www.tldp.org/docs.html#howto>. - - To compile this driver as a module, choose M here: the module - will be called 8139too. This is recommended. - -config 8139TOO_PIO - bool "Use PIO instead of MMIO" - default y - depends on 8139TOO - help - This instructs the driver to use programmed I/O ports (PIO) instead - of PCI shared memory (MMIO). This can possibly solve some problems - in case your mainboard has memory consistency issues. If unsure, - say N. - -config 8139TOO_TUNE_TWISTER - bool "Support for uncommon RTL-8139 rev. K (automatic channel equalization)" - depends on 8139TOO - help - This implements a function which might come in handy in case you - are using low quality on long cabling. It is required for RealTek - RTL-8139 revision K boards, and totally unused otherwise. It tries - to match the transceiver to the cable characteristics. This is - experimental since hardly documented by the manufacturer. - If unsure, say Y. - -config 8139TOO_8129 - bool "Support for older RTL-8129/8130 boards" - depends on 8139TOO - help - This enables support for the older and uncommon RTL-8129 and - RTL-8130 chips, which support MII via an external transceiver, - instead of an internal one. Disabling this option will save some - memory by making the code size smaller. If unsure, say Y. - -config 8139_OLD_RX_RESET - bool "Use older RX-reset method" - depends on 8139TOO - help - The 8139too driver was recently updated to contain a more rapid - reset sequence, in the face of severe receive errors. This "new" - RX-reset method should be adequate for all boards. But if you - experience problems, you can enable this option to restore the - old RX-reset behavior. If unsure, say N. - config R6040 tristate "RDC R6040 Fast Ethernet Adapter support" depends on NET_PCI && PCI @@ -776,18 +709,6 @@ config VIA_RHINE_MMIO If unsure, say Y. -config SC92031 - tristate "Silan SC92031 PCI Fast Ethernet Adapter driver (EXPERIMENTAL)" - depends on NET_PCI && PCI && EXPERIMENTAL - select CRC32 - ---help--- - This is a driver for the Fast Ethernet PCI network cards based on - the Silan SC92031 chip (sometimes also called Rsltek 8139D). If you - have one of these, say Y here. - - To compile this driver as a module, choose M here: the module - will be called sc92031. This is recommended. - config CPMAC tristate "TI AR7 CPMAC Ethernet support (EXPERIMENTAL)" depends on NET_ETHERNET && EXPERIMENTAL && AR7 @@ -819,21 +740,6 @@ config NET_POCKET the questions about this class of network devices. If you say Y, you will be asked for your specific device in the following questions. -config ATP - tristate "AT-LAN-TEC/RealTek pocket adapter support" - depends on NET_POCKET && PARPORT && X86 - select CRC32 - ---help--- - This is a network (Ethernet) device which attaches to your parallel - port. Read <file:drivers/net/atp.c> as well as the Ethernet-HOWTO, - available from <http://www.tldp.org/docs.html#howto>, if you - want to use this. If you intend to use this driver, you should have - said N to the "Parallel printer support", because the two drivers - don't like each other. - - To compile this driver as a module, choose M here: the module - will be called atp. - config DE600 tristate "D-Link DE600 pocket adapter support" depends on NET_POCKET && PARPORT @@ -1006,18 +912,6 @@ config YELLOWFIN To compile this driver as a module, choose M here: the module will be called yellowfin. This is recommended. -config R8169 - tristate "Realtek 8169 gigabit ethernet support" - depends on PCI - select FW_LOADER - select CRC32 - select MII - ---help--- - Say Y here if you have a Realtek 8169 PCI Gigabit Ethernet adapter. - - To compile this driver as a module, choose M here: the module - will be called r8169. This is recommended. - config SIS190 tristate "SiS190/SiS191 gigabit ethernet support" depends on PCI |