diff options
Diffstat (limited to 'drivers/net/bnx2x_link.c')
| -rw-r--r-- | drivers/net/bnx2x_link.c | 1258 |
1 files changed, 805 insertions, 453 deletions
diff --git a/drivers/net/bnx2x_link.c b/drivers/net/bnx2x_link.c index ff2743db10d..8b92c6ad075 100644 --- a/drivers/net/bnx2x_link.c +++ b/drivers/net/bnx2x_link.c @@ -31,17 +31,16 @@ /********************************************************/ #define SUPPORT_CL73 0 /* Currently no */ -#define ETH_HLEN 14 +#define ETH_HLEN 14 #define ETH_OVREHEAD (ETH_HLEN + 8)/* 8 for CRC + VLAN*/ #define ETH_MIN_PACKET_SIZE 60 #define ETH_MAX_PACKET_SIZE 1500 #define ETH_MAX_JUMBO_PACKET_SIZE 9600 #define MDIO_ACCESS_TIMEOUT 1000 #define BMAC_CONTROL_RX_ENABLE 2 -#define MAX_MTU_SIZE 5000 /***********************************************************/ -/* Shortcut definitions */ +/* Shortcut definitions */ /***********************************************************/ #define NIG_STATUS_XGXS0_LINK10G \ @@ -80,12 +79,12 @@ #define AUTONEG_CL37 SHARED_HW_CFG_AN_ENABLE_CL37 #define AUTONEG_CL73 SHARED_HW_CFG_AN_ENABLE_CL73 -#define AUTONEG_BAM SHARED_HW_CFG_AN_ENABLE_BAM -#define AUTONEG_PARALLEL \ +#define AUTONEG_BAM SHARED_HW_CFG_AN_ENABLE_BAM +#define AUTONEG_PARALLEL \ SHARED_HW_CFG_AN_ENABLE_PARALLEL_DETECTION -#define AUTONEG_SGMII_FIBER_AUTODET \ +#define AUTONEG_SGMII_FIBER_AUTODET \ SHARED_HW_CFG_AN_EN_SGMII_FIBER_AUTO_DETECT -#define AUTONEG_REMOTE_PHY SHARED_HW_CFG_AN_ENABLE_REMOTE_PHY +#define AUTONEG_REMOTE_PHY SHARED_HW_CFG_AN_ENABLE_REMOTE_PHY #define GP_STATUS_PAUSE_RSOLUTION_TXSIDE \ MDIO_GP_STATUS_TOP_AN_STATUS1_PAUSE_RSOLUTION_TXSIDE @@ -202,11 +201,10 @@ static void bnx2x_emac_init(struct link_params *params, /* init emac - use read-modify-write */ /* self clear reset */ val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE); - EMAC_WR(EMAC_REG_EMAC_MODE, (val | EMAC_MODE_RESET)); + EMAC_WR(bp, EMAC_REG_EMAC_MODE, (val | EMAC_MODE_RESET)); timeout = 200; - do - { + do { val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE); DP(NETIF_MSG_LINK, "EMAC reset reg is %u\n", val); if (!timeout) { @@ -214,18 +212,18 @@ static void bnx2x_emac_init(struct link_params *params, return; } timeout--; - }while (val & EMAC_MODE_RESET); + } while (val & EMAC_MODE_RESET); /* Set mac address */ val = ((params->mac_addr[0] << 8) | params->mac_addr[1]); - EMAC_WR(EMAC_REG_EMAC_MAC_MATCH, val); + EMAC_WR(bp, EMAC_REG_EMAC_MAC_MATCH, val); val = ((params->mac_addr[2] << 24) | (params->mac_addr[3] << 16) | (params->mac_addr[4] << 8) | params->mac_addr[5]); - EMAC_WR(EMAC_REG_EMAC_MAC_MATCH + 4, val); + EMAC_WR(bp, EMAC_REG_EMAC_MAC_MATCH + 4, val); } static u8 bnx2x_emac_enable(struct link_params *params, @@ -286,7 +284,7 @@ static u8 bnx2x_emac_enable(struct link_params *params, if (CHIP_REV_IS_SLOW(bp)) { /* config GMII mode */ val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE); - EMAC_WR(EMAC_REG_EMAC_MODE, + EMAC_WR(bp, EMAC_REG_EMAC_MODE, (val | EMAC_MODE_PORT_GMII)); } else { /* ASIC */ /* pause enable/disable */ @@ -298,17 +296,19 @@ static u8 bnx2x_emac_enable(struct link_params *params, EMAC_RX_MODE_FLOW_EN); bnx2x_bits_dis(bp, emac_base + EMAC_REG_EMAC_TX_MODE, - EMAC_TX_MODE_EXT_PAUSE_EN); + (EMAC_TX_MODE_EXT_PAUSE_EN | + EMAC_TX_MODE_FLOW_EN)); if (vars->flow_ctrl & FLOW_CTRL_TX) bnx2x_bits_en(bp, emac_base + EMAC_REG_EMAC_TX_MODE, - EMAC_TX_MODE_EXT_PAUSE_EN); + (EMAC_TX_MODE_EXT_PAUSE_EN | + EMAC_TX_MODE_FLOW_EN)); } /* KEEP_VLAN_TAG, promiscuous */ val = REG_RD(bp, emac_base + EMAC_REG_EMAC_RX_MODE); val |= EMAC_RX_MODE_KEEP_VLAN_TAG | EMAC_RX_MODE_PROMISCUOUS; - EMAC_WR(EMAC_REG_EMAC_RX_MODE, val); + EMAC_WR(bp, EMAC_REG_EMAC_RX_MODE, val); /* Set Loopback */ val = REG_RD(bp, emac_base + EMAC_REG_EMAC_MODE); @@ -316,10 +316,10 @@ static u8 bnx2x_emac_enable(struct link_params *params, val |= 0x810; else val &= ~0x810; - EMAC_WR(EMAC_REG_EMAC_MODE, val); + EMAC_WR(bp, EMAC_REG_EMAC_MODE, val); /* enable emac for jumbo packets */ - EMAC_WR(EMAC_REG_EMAC_RX_MTU_SIZE, + EMAC_WR(bp, EMAC_REG_EMAC_RX_MTU_SIZE, (EMAC_RX_MTU_SIZE_JUMBO_ENA | (ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD))); @@ -591,9 +591,9 @@ void bnx2x_link_status_update(struct link_params *params, vars->flow_ctrl &= ~FLOW_CTRL_RX; if (vars->phy_flags & PHY_XGXS_FLAG) { - if (params->req_line_speed && - ((params->req_line_speed == SPEED_10) || - (params->req_line_speed == SPEED_100))) { + if (vars->line_speed && + ((vars->line_speed == SPEED_10) || + (vars->line_speed == SPEED_100))) { vars->phy_flags |= PHY_SGMII_FLAG; } else { vars->phy_flags &= ~PHY_SGMII_FLAG; @@ -645,7 +645,7 @@ static void bnx2x_bmac_rx_disable(struct bnx2x *bp, u8 port) u32 bmac_addr = port ? NIG_REG_INGRESS_BMAC1_MEM : NIG_REG_INGRESS_BMAC0_MEM; u32 wb_data[2]; - u32 nig_bmac_enable = REG_RD(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4); + u32 nig_bmac_enable = REG_RD(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4); /* Only if the bmac is out of reset */ if (REG_RD(bp, MISC_REG_RESET_REG_2) & @@ -670,7 +670,6 @@ static u8 bnx2x_pbf_update(struct link_params *params, u32 flow_ctrl, u8 port = params->port; u32 init_crd, crd; u32 count = 1000; - u32 pause = 0; /* disable port */ REG_WR(bp, PBF_REG_DISABLE_NEW_TASK_PROC_P0 + port*4, 0x1); @@ -693,33 +692,25 @@ static u8 bnx2x_pbf_update(struct link_params *params, u32 flow_ctrl, return -EINVAL; } - if (flow_ctrl & FLOW_CTRL_RX) - pause = 1; - REG_WR(bp, PBF_REG_P0_PAUSE_ENABLE + port*4, pause); - if (pause) { + if (flow_ctrl & FLOW_CTRL_RX || + line_speed == SPEED_10 || + line_speed == SPEED_100 || + line_speed == SPEED_1000 || + line_speed == SPEED_2500) { + REG_WR(bp, PBF_REG_P0_PAUSE_ENABLE + port*4, 1); /* update threshold */ REG_WR(bp, PBF_REG_P0_ARB_THRSH + port*4, 0); /* update init credit */ - init_crd = 778; /* (800-18-4) */ + init_crd = 778; /* (800-18-4) */ } else { u32 thresh = (ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD)/16; - + REG_WR(bp, PBF_REG_P0_PAUSE_ENABLE + port*4, 0); /* update threshold */ REG_WR(bp, PBF_REG_P0_ARB_THRSH + port*4, thresh); /* update init credit */ switch (line_speed) { - case SPEED_10: - case SPEED_100: - case SPEED_1000: - init_crd = thresh + 55 - 22; - break; - - case SPEED_2500: - init_crd = thresh + 138 - 22; - break; - case SPEED_10000: init_crd = thresh + 553 - 22; break; @@ -764,10 +755,10 @@ static u32 bnx2x_get_emac_base(u32 ext_phy_type, u8 port) emac_base = GRCBASE_EMAC0; break; case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073: - emac_base = (port) ? GRCBASE_EMAC0: GRCBASE_EMAC1; + emac_base = (port) ? GRCBASE_EMAC0 : GRCBASE_EMAC1; break; default: - emac_base = (port) ? GRCBASE_EMAC1: GRCBASE_EMAC0; + emac_base = (port) ? GRCBASE_EMAC1 : GRCBASE_EMAC0; break; } return emac_base; @@ -1044,7 +1035,7 @@ static void bnx2x_set_swap_lanes(struct link_params *params) } static void bnx2x_set_parallel_detection(struct link_params *params, - u8 phy_flags) + u8 phy_flags) { struct bnx2x *bp = params->bp; u16 control2; @@ -1114,7 +1105,7 @@ static void bnx2x_set_autoneg(struct link_params *params, MDIO_COMBO_IEEE0_MII_CONTROL, ®_val); /* CL37 Autoneg Enabled */ - if (params->req_line_speed == SPEED_AUTO_NEG) + if (vars->line_speed == SPEED_AUTO_NEG) reg_val |= MDIO_COMBO_IEEO_MII_CONTROL_AN_EN; else /* CL37 Autoneg Disabled */ reg_val &= ~(MDIO_COMBO_IEEO_MII_CONTROL_AN_EN | @@ -1132,7 +1123,7 @@ static void bnx2x_set_autoneg(struct link_params *params, MDIO_REG_BANK_SERDES_DIGITAL, MDIO_SERDES_DIGITAL_A_1000X_CONTROL1, ®_val); reg_val &= ~MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_SIGNAL_DETECT_EN; - if (params->req_line_speed == SPEED_AUTO_NEG) + if (vars->line_speed == SPEED_AUTO_NEG) reg_val |= MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET; else reg_val &= ~MDIO_SERDES_DIGITAL_A_1000X_CONTROL1_AUTODET; @@ -1148,7 +1139,7 @@ static void bnx2x_set_autoneg(struct link_params *params, MDIO_REG_BANK_BAM_NEXT_PAGE, MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL, ®_val); - if (params->req_line_speed == SPEED_AUTO_NEG) { + if (vars->line_speed == SPEED_AUTO_NEG) { /* Enable BAM aneg Mode and TetonII aneg Mode */ reg_val |= (MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_BAM_MODE | MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL_TETON_AN); @@ -1164,7 +1155,7 @@ static void bnx2x_set_autoneg(struct link_params *params, reg_val); /* Enable Clause 73 Aneg */ - if ((params->req_line_speed == SPEED_AUTO_NEG) && + if ((vars->line_speed == SPEED_AUTO_NEG) && (SUPPORT_CL73)) { /* Enable BAM Station Manager */ @@ -1226,7 +1217,8 @@ static void bnx2x_set_autoneg(struct link_params *params, } /* program SerDes, forced speed */ -static void bnx2x_program_serdes(struct link_params *params) +static void bnx2x_program_serdes(struct link_params *params, + struct link_vars *vars) { struct bnx2x *bp = params->bp; u16 reg_val; @@ -1248,28 +1240,35 @@ static void bnx2x_program_serdes(struct link_params *params) /* program speed - needed only if the speed is greater than 1G (2.5G or 10G) */ - if (!((params->req_line_speed == SPEED_1000) || - (params->req_line_speed == SPEED_100) || - (params->req_line_speed == SPEED_10))) { - CL45_RD_OVER_CL22(bp, params->port, + CL45_RD_OVER_CL22(bp, params->port, params->phy_addr, MDIO_REG_BANK_SERDES_DIGITAL, MDIO_SERDES_DIGITAL_MISC1, ®_val); - /* clearing the speed value before setting the right speed */ - reg_val &= ~MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_MASK; + /* clearing the speed value before setting the right speed */ + DP(NETIF_MSG_LINK, "MDIO_REG_BANK_SERDES_DIGITAL = 0x%x\n", reg_val); + + reg_val &= ~(MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_MASK | + MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_SEL); + + if (!((vars->line_speed == SPEED_1000) || + (vars->line_speed == SPEED_100) || + (vars->line_speed == SPEED_10))) { + reg_val |= (MDIO_SERDES_DIGITAL_MISC1_REFCLK_SEL_156_25M | MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_SEL); - if (params->req_line_speed == SPEED_10000) + if (vars->line_speed == SPEED_10000) reg_val |= MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_10G_CX4; - if (params->req_line_speed == SPEED_13000) + if (vars->line_speed == SPEED_13000) reg_val |= MDIO_SERDES_DIGITAL_MISC1_FORCE_SPEED_13G; - CL45_WR_OVER_CL22(bp, params->port, + } + + CL45_WR_OVER_CL22(bp, params->port, params->phy_addr, MDIO_REG_BANK_SERDES_DIGITAL, MDIO_SERDES_DIGITAL_MISC1, reg_val); - } + } static void bnx2x_set_brcm_cl37_advertisment(struct link_params *params) @@ -1295,48 +1294,49 @@ static void bnx2x_set_brcm_cl37_advertisment(struct link_params *params) MDIO_OVER_1G_UP3, 0); } -static void bnx2x_set_ieee_aneg_advertisment(struct link_params *params, - u32 *ieee_fc) +static void bnx2x_calc_ieee_aneg_adv(struct link_params *params, u32 *ieee_fc) { - struct bnx2x *bp = params->bp; - /* for AN, we are always publishing full duplex */ - u16 an_adv = MDIO_COMBO_IEEE0_AUTO_NEG_ADV_FULL_DUPLEX; - + *ieee_fc = MDIO_COMBO_IEEE0_AUTO_NEG_ADV_FULL_DUPLEX; /* resolve pause mode and advertisement * Please refer to Table 28B-3 of the 802.3ab-1999 spec */ switch (params->req_flow_ctrl) { case FLOW_CTRL_AUTO: - if (params->mtu <= MAX_MTU_SIZE) { - an_adv |= + if (params->req_fc_auto_adv == FLOW_CTRL_BOTH) { + *ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH; } else { - an_adv |= + *ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC; } break; case FLOW_CTRL_TX: - an_adv |= + *ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC; break; case FLOW_CTRL_RX: case FLOW_CTRL_BOTH: - an_adv |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH; + *ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH; break; case FLOW_CTRL_NONE: default: - an_adv |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_NONE; + *ieee_fc |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_NONE; break; } +} - *ieee_fc = an_adv; +static void bnx2x_set_ieee_aneg_advertisment(struct link_params *params, + u32 ieee_fc) +{ + struct bnx2x *bp = params->bp; + /* for AN, we are always publishing full duplex */ CL45_WR_OVER_CL22(bp, params->port, params->phy_addr, MDIO_REG_BANK_COMBO_IEEE0, - MDIO_COMBO_IEEE0_AUTO_NEG_ADV, an_adv); + MDIO_COMBO_IEEE0_AUTO_NEG_ADV, (u16)ieee_fc); } static void bnx2x_restart_autoneg(struct link_params *params) @@ -1382,7 +1382,8 @@ static void bnx2x_restart_autoneg(struct link_params *params) } } -static void bnx2x_initialize_sgmii_process(struct link_params *params) +static void bnx2x_initialize_sgmii_process(struct link_params *params, + struct link_vars *vars) { struct bnx2x *bp = params->bp; u16 control1; @@ -1406,7 +1407,7 @@ static void bnx2x_initialize_sgmii_process(struct link_params *params) control1); /* if forced speed */ - if (!(params->req_line_speed == SPEED_AUTO_NEG)) { + if (!(vars->line_speed == SPEED_AUTO_NEG)) { /* set speed, disable autoneg */ u16 mii_control; @@ -1419,7 +1420,7 @@ static void bnx2x_initialize_sgmii_process(struct link_params *params) MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_MASK| MDIO_COMBO_IEEO_MII_CONTROL_FULL_DUPLEX); - switch (params->req_line_speed) { + switch (vars->line_speed) { case SPEED_100: mii_control |= MDIO_COMBO_IEEO_MII_CONTROL_MAN_SGMII_SP_100; @@ -1433,8 +1434,8 @@ static void bnx2x_initialize_sgmii_process(struct link_params *params) break; default: /* invalid speed for SGMII */ - DP(NETIF_MSG_LINK, "Invalid req_line_speed 0x%x\n", - params->req_line_speed); + DP(NETIF_MSG_LINK, "Invalid line_speed 0x%x\n", + vars->line_speed); break; } @@ -1460,20 +1461,20 @@ static void bnx2x_initialize_sgmii_process(struct link_params *params) */ static void bnx2x_pause_resolve(struct link_vars *vars, u32 pause_result) -{ - switch (pause_result) { /* ASYM P ASYM P */ - case 0xb: /* 1 0 1 1 */ +{ /* LD LP */ + switch (pause_result) { /* ASYM P ASYM P */ + case 0xb: /* 1 0 1 1 */ vars->flow_ctrl = FLOW_CTRL_TX; break; - case 0xe: /* 1 1 1 0 */ + case 0xe: /* 1 1 1 0 */ vars->flow_ctrl = FLOW_CTRL_RX; break; - case 0x5: /* 0 1 0 1 */ - case 0x7: /* 0 1 1 1 */ - case 0xd: /* 1 1 0 1 */ - case 0xf: /* 1 1 1 1 */ + case 0x5: /* 0 1 0 1 */ + case 0x7: /* 0 1 1 1 */ + case 0xd: /* 1 1 0 1 */ + case 0xf: /* 1 1 1 1 */ vars->flow_ctrl = FLOW_CTRL_BOTH; break; @@ -1531,6 +1532,28 @@ static u8 bnx2x_ext_phy_resove_fc(struct link_params *params, DP(NETIF_MSG_LINK, "Ext PHY pause result 0x%x \n", pause_result); bnx2x_pause_resolve(vars, pause_result); + if (vars->flow_ctrl == FLOW_CTRL_NONE && + ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073) { + bnx2x_cl45_read(bp, port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_CL37_FC_LD, &ld_pause); + + bnx2x_cl45_read(bp, port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_CL37_FC_LP, &lp_pause); + pause_result = (ld_pause & + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) >> 5; + pause_result |= (lp_pause & + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) >> 7; + + bnx2x_pause_resolve(vars, pause_result); + DP(NETIF_MSG_LINK, "Ext PHY CL37 pause result 0x%x \n", + pause_result); + } } return ret; } @@ -1541,8 +1564,8 @@ static void bnx2x_flow_ctrl_resolve(struct link_params *params, u32 gp_status) { struct bnx2x *bp = params->bp; - u16 ld_pause; /* local driver */ - u16 lp_pause; /* link partner */ + u16 ld_pause; /* local driver */ + u16 lp_pause; /* link partner */ u16 pause_result; vars->flow_ctrl = FLOW_CTRL_NONE; @@ -1573,13 +1596,10 @@ static void bnx2x_flow_ctrl_resolve(struct link_params *params, (bnx2x_ext_phy_resove_fc(params, vars))) { return; } else { - vars->flow_ctrl = params->req_flow_ctrl; - if (vars->flow_ctrl == FLOW_CTRL_AUTO) { - if (params->mtu <= MAX_MTU_SIZE) - vars->flow_ctrl = FLOW_CTRL_BOTH; - else - vars->flow_ctrl = FLOW_CTRL_TX; - } + if (params->req_flow_ctrl == FLOW_CTRL_AUTO) + vars->flow_ctrl = params->req_fc_auto_adv; + else + vars->flow_ctrl = params->req_flow_ctrl; } DP(NETIF_MSG_LINK, "flow_ctrl 0x%x\n", vars->flow_ctrl); } @@ -1590,6 +1610,7 @@ static u8 bnx2x_link_settings_status(struct link_params *params, u32 gp_status) { struct bnx2x *bp = params->bp; + u8 rc = 0; vars->link_status = 0; @@ -1690,7 +1711,11 @@ static u8 bnx2x_link_settings_status(struct link_params *params, vars->link_status |= LINK_STATUS_SERDES_LINK; - if (params->req_line_speed == SPEED_AUTO_NEG) { + if ((params->req_line_speed == SPEED_AUTO_NEG) && + ((XGXS_EXT_PHY_TYPE(params->ext_phy_config) == + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) || + (XGXS_EXT_PHY_TYPE(params->ext_phy_config) == + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705))) { vars->autoneg = AUTO_NEG_ENABLED; if (gp_status & MDIO_AN_CL73_OR_37_COMPLETE) { @@ -1705,18 +1730,18 @@ static u8 bnx2x_link_settings_status(struct link_params *params, } if (vars->flow_ctrl & FLOW_CTRL_TX) - vars->link_status |= - LINK_STATUS_TX_FLOW_CONTROL_ENABLED; + vars->link_status |= + LINK_STATUS_TX_FLOW_CONTROL_ENABLED; if (vars->flow_ctrl & FLOW_CTRL_RX) - vars->link_status |= - LINK_STATUS_RX_FLOW_CONTROL_ENABLED; + vars->link_status |= + LINK_STATUS_RX_FLOW_CONTROL_ENABLED; } else { /* link_down */ DP(NETIF_MSG_LINK, "phy link down\n"); vars->phy_link_up = 0; - vars->line_speed = 0; + vars->duplex = DUPLEX_FULL; vars->flow_ctrl = FLOW_CTRL_NONE; vars->autoneg = AUTO_NEG_DISABLED; @@ -1817,15 +1842,15 @@ static u8 bnx2x_emac_program(struct link_params *params, } /*****************************************************************************/ -/* External Phy section */ +/* External Phy section */ /*****************************************************************************/ -static void bnx2x_hw_reset(struct bnx2x *bp) +static void bnx2x_hw_reset(struct bnx2x *bp, u8 port) { bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1, - MISC_REGISTERS_GPIO_OUTPUT_LOW); + MISC_REGISTERS_GPIO_OUTPUT_LOW, port); msleep(1); bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1, - MISC_REGISTERS_GPIO_OUTPUT_HIGH); + MISC_REGISTERS_GPIO_OUTPUT_HIGH, port); } static void bnx2x_ext_phy_reset(struct link_params *params, @@ -1854,10 +1879,11 @@ static void bnx2x_ext_phy_reset(struct link_params *params, /* Restore normal power mode*/ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, - MISC_REGISTERS_GPIO_OUTPUT_HIGH); + MISC_REGISTERS_GPIO_OUTPUT_HIGH, + params->port); /* HW reset */ - bnx2x_hw_reset(bp); + bnx2x_hw_reset(bp, params->port); bnx2x_cl45_write(bp, params->port, ext_phy_type, @@ -1869,7 +1895,8 @@ static void bnx2x_ext_phy_reset(struct link_params *params, /* Unset Low Power Mode and SW reset */ /* Restore normal power mode*/ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, - MISC_REGISTERS_GPIO_OUTPUT_HIGH); + MISC_REGISTERS_GPIO_OUTPUT_HIGH, + params->port); DP(NETIF_MSG_LINK, "XGXS 8072\n"); bnx2x_cl45_write(bp, params->port, @@ -1887,19 +1914,14 @@ static void bnx2x_ext_phy_reset(struct link_params *params, /* Restore normal power mode*/ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, - MISC_REGISTERS_GPIO_OUTPUT_HIGH); + MISC_REGISTERS_GPIO_OUTPUT_HIGH, + params->port); bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1, - MISC_REGISTERS_GPIO_OUTPUT_HIGH); + MISC_REGISTERS_GPIO_OUTPUT_HIGH, + params->port); DP(NETIF_MSG_LINK, "XGXS 8073\n"); - bnx2x_cl45_write(bp, - params->port, - ext_phy_type, - ext_phy_addr, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_CTRL, - 1<<15); } break; @@ -1908,10 +1930,11 @@ static void bnx2x_ext_phy_reset(struct link_params *params, /* Restore normal power mode*/ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, - MISC_REGISTERS_GPIO_OUTPUT_HIGH); + MISC_REGISTERS_GPIO_OUTPUT_HIGH, + params->port); /* HW reset */ - bnx2x_hw_reset(bp); + bnx2x_hw_reset(bp, params->port); break; @@ -1934,7 +1957,7 @@ static void bnx2x_ext_phy_reset(struct link_params *params, case PORT_HW_CFG_SERDES_EXT_PHY_TYPE_BCM5482: DP(NETIF_MSG_LINK, "SerDes 5482\n"); - bnx2x_hw_reset(bp); + bnx2x_hw_reset(bp, params->port); break; default: @@ -2098,42 +2121,45 @@ static u8 bnx2x_bcm8073_xaui_wa(struct link_params *params) } -static void bnx2x_bcm8073_external_rom_boot(struct link_params *params) +static void bnx2x_bcm8073_external_rom_boot(struct bnx2x *bp, u8 port, + u8 ext_phy_addr) { - struct bnx2x *bp = params->bp; - u8 port = params->port; - u8 ext_phy_addr = ((params->ext_phy_config & - PORT_HW_CFG_XGXS_EXT_PHY_ADDR_MASK) >> - PORT_HW_CFG_XGXS_EXT_PHY_ADDR_SHIFT); - u32 ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config); - u16 fw_ver1, fw_ver2, val; - /* Need to wait 100ms after reset */ - msleep(100); - /* Boot port from external ROM */ + u16 fw_ver1, fw_ver2; + /* Boot port from external ROM */ /* EDC grst */ - bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr, MDIO_PMA_DEVAD, MDIO_PMA_REG_GEN_CTRL, 0x0001); /* ucode reboot and rst */ - bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr, MDIO_PMA_DEVAD, MDIO_PMA_REG_GEN_CTRL, 0x008c); - bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr, MDIO_PMA_DEVAD, MDIO_PMA_REG_MISC_CTRL1, 0x0001); /* Reset internal microprocessor */ - bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr, MDIO_PMA_DEVAD, MDIO_PMA_REG_GEN_CTRL, MDIO_PMA_REG_GEN_CTRL_ROM_MICRO_RESET); /* Release srst bit */ - bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr, MDIO_PMA_DEVAD, MDIO_PMA_REG_GEN_CTRL, MDIO_PMA_REG_GEN_CTRL_ROM_RESET_INTERNAL_MP); @@ -2142,35 +2168,52 @@ static void bnx2x_bcm8073_external_rom_boot(struct link_params *params) msleep(100); /* Clear ser_boot_ctl bit */ - bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr, MDIO_PMA_DEVAD, MDIO_PMA_REG_MISC_CTRL1, 0x0000); - bnx2x_cl45_read(bp, port, ext_phy_type, ext_phy_addr, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_ROM_VER1, &fw_ver1); - bnx2x_cl45_read(bp, port, ext_phy_type, ext_phy_addr, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_ROM_VER2, &fw_ver2); + bnx2x_cl45_read(bp, port, PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_ROM_VER1, &fw_ver1); + bnx2x_cl45_read(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_ROM_VER2, &fw_ver2); DP(NETIF_MSG_LINK, "8073 FW version 0x%x:0x%x\n", fw_ver1, fw_ver2); - /* Only set bit 10 = 1 (Tx power down) */ - bnx2x_cl45_read(bp, port, ext_phy_type, ext_phy_addr, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_TX_POWER_DOWN, &val); +} +static void bnx2x_bcm807x_force_10G(struct link_params *params) +{ + struct bnx2x *bp = params->bp; + u8 port = params->port; + u8 ext_phy_addr = ((params->ext_phy_config & + PORT_HW_CFG_XGXS_EXT_PHY_ADDR_MASK) >> + PORT_HW_CFG_XGXS_EXT_PHY_ADDR_SHIFT); + u32 ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config); + + /* Force KR or KX */ bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, MDIO_PMA_DEVAD, - MDIO_PMA_REG_TX_POWER_DOWN, (val | 1<<10)); - - msleep(600); - /* Release bit 10 (Release Tx power down) */ + MDIO_PMA_REG_CTRL, + 0x2040); bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, MDIO_PMA_DEVAD, - MDIO_PMA_REG_TX_POWER_DOWN, (val & (~(1<<10)))); - + MDIO_PMA_REG_10G_CTRL2, + 0x000b); + bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_BCM_CTRL, + 0x0000); + bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_CTRL, + 0x0000); } - static void bnx2x_bcm8073_set_xaui_low_power_mode(struct link_params *params) { struct bnx2x *bp = params->bp; @@ -2236,32 +2279,51 @@ static void bnx2x_bcm8073_set_xaui_low_power_mode(struct link_params *params) bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, MDIO_XS_DEVAD, MDIO_XS_PLL_SEQUENCER, val); } -static void bnx2x_bcm807x_force_10G(struct link_params *params) + +static void bnx2x_8073_set_pause_cl37(struct link_params *params, + struct link_vars *vars) { + struct bnx2x *bp = params->bp; - u8 port = params->port; + u16 cl37_val; u8 ext_phy_addr = ((params->ext_phy_config & PORT_HW_CFG_XGXS_EXT_PHY_ADDR_MASK) >> PORT_HW_CFG_XGXS_EXT_PHY_ADDR_SHIFT); u32 ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config); - /* Force KR or KX */ - bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_CTRL, - 0x2040); - bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_10G_CTRL2, - 0x000b); - bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_BCM_CTRL, - 0x0000); - bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_CL37_FC_LD, &cl37_val); + + cl37_val &= ~MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH; + /* Please refer to Table 28B-3 of 802.3ab-1999 spec. */ + + if ((vars->ieee_fc & + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_SYMMETRIC) == + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_SYMMETRIC) { + cl37_val |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_SYMMETRIC; + } + if ((vars->ieee_fc & + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) == + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) { + cl37_val |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC; + } + if ((vars->ieee_fc & + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) == + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) { + cl37_val |= MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH; + } + DP(NETIF_MSG_LINK, + "Ext phy AN advertize cl37 0x%x\n", cl37_val); + + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, MDIO_AN_DEVAD, - MDIO_AN_REG_CTRL, - 0x0000); + MDIO_AN_REG_CL37_FC_LD, cl37_val); + msleep(500); } static void bnx2x_ext_phy_set_pause(struct link_params *params, @@ -2282,13 +2344,16 @@ static void bnx2x_ext_phy_set_pause(struct link_params *params, MDIO_AN_REG_ADV_PAUSE, &val); val &= ~MDIO_AN_REG_ADV_PAUSE_BOTH; + /* Please refer to Table 28B-3 of 802.3ab-1999 spec. */ - if (vars->ieee_fc & + if ((vars->ieee_fc & + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) == MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_ASYMMETRIC) { val |= MDIO_AN_REG_ADV_PAUSE_ASYMMETRIC; } - if (vars->ieee_fc & + if ((vars->ieee_fc & + MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) == MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_BOTH) { val |= MDIO_AN_REG_ADV_PAUSE_PAUSE; @@ -2302,6 +2367,65 @@ static void bnx2x_ext_phy_set_pause(struct link_params *params, MDIO_AN_REG_ADV_PAUSE, val); } + +static void bnx2x_init_internal_phy(struct link_params *params, + struct link_vars *vars) +{ + struct bnx2x *bp = params->bp; + u8 port = params->port; + if (!(vars->phy_flags & PHY_SGMII_FLAG)) { + u16 bank, rx_eq; + + rx_eq = ((params->serdes_config & + PORT_HW_CFG_SERDES_RX_DRV_EQUALIZER_MASK) >> + PORT_HW_CFG_SERDES_RX_DRV_EQUALIZER_SHIFT); + + DP(NETIF_MSG_LINK, "setting rx eq to 0x%x\n", rx_eq); + for (bank = MDIO_REG_BANK_RX0; bank <= MDIO_REG_BANK_RX_ALL; + bank += (MDIO_REG_BANK_RX1-MDIO_REG_BANK_RX0)) { + CL45_WR_OVER_CL22(bp, port, + params->phy_addr, + bank , + MDIO_RX0_RX_EQ_BOOST, + ((rx_eq & + MDIO_RX0_RX_EQ_BOOST_EQUALIZER_CTRL_MASK) | + MDIO_RX0_RX_EQ_BOOST_OFFSET_CTRL)); + } + + /* forced speed requested? */ + if (vars->line_speed != SPEED_AUTO_NEG) { + DP(NETIF_MSG_LINK, "not SGMII, no AN\n"); + + /* disable autoneg */ + bnx2x_set_autoneg(params, vars); + + /* program speed and duplex */ + bnx2x_program_serdes(params, vars); + + } else { /* AN_mode */ + DP(NETIF_MSG_LINK, "not SGMII, AN\n"); + + /* AN enabled */ + bnx2x_set_brcm_cl37_advertisment(params); + + /* program duplex & pause advertisement (for aneg) */ + bnx2x_set_ieee_aneg_advertisment(params, + vars->ieee_fc); + + /* enable autoneg */ + bnx2x_set_autoneg(params, vars); + + /* enable and restart AN */ + bnx2x_restart_autoneg(params); + } + + } else { /* SGMII mode */ + DP(NETIF_MSG_LINK, "SGMII\n"); + + bnx2x_initialize_sgmii_process(params, vars); + } +} + static u8 bnx2x_ext_phy_init(struct link_params *params, struct link_vars *vars) { struct bnx2x *bp = params->bp; @@ -2343,7 +2467,6 @@ static u8 bnx2x_ext_phy_init(struct link_params *params, struct link_vars *vars) switch (ext_phy_type) { case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT: - DP(NETIF_MSG_LINK, "XGXS Direct\n"); break; case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705: @@ -2419,7 +2542,7 @@ static u8 bnx2x_ext_phy_init(struct link_params *params, struct link_vars *vars) ext_phy_type, ext_phy_addr, MDIO_AN_DEVAD, - MDIO_AN_REG_CL37_FD, + MDIO_AN_REG_CL37_FC_LP, 0x0020); /* Enable CL37 AN */ bnx2x_cl45_write(bp, params->port, @@ -2458,54 +2581,43 @@ static u8 bnx2x_ext_phy_init(struct link_params *params, struct link_vars *vars) rx_alarm_ctrl_val = 0x400; lasi_ctrl_val = 0x0004; } else { - /* In 8073, port1 is directed through emac0 and - * port0 is directed through emac1 - */ rx_alarm_ctrl_val = (1<<2); - /*lasi_ctrl_val = 0x0005;*/ lasi_ctrl_val = 0x0004; } - /* Wait for soft reset to get cleared upto 1 sec */ - for (cnt = 0; cnt < 1000; cnt++) { - bnx2x_cl45_read(bp, params->port, - ext_phy_type, - ext_phy_addr, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_CTRL, - &ctrl); - if (!(ctrl & (1<<15))) - break; - msleep(1); - } - DP(NETIF_MSG_LINK, - "807x control reg 0x%x (after %d ms)\n", - ctrl, cnt); + /* enable LASI */ + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_RX_ALARM_CTRL, + rx_alarm_ctrl_val); + + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_LASI_CTRL, + lasi_ctrl_val); + + bnx2x_8073_set_pause_cl37(params, vars); if (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072){ bnx2x_bcm8072_external_rom_boot(params); } else { - bnx2x_bcm8073_external_rom_boot(params); + /* In case of 8073 with long xaui lines, don't set the 8073 xaui low power*/ bnx2x_bcm8073_set_xaui_low_power_mode(params); } - /* enable LASI */ - bnx2x_cl45_write(bp, params->port, - ext_phy_type, - ext_phy_addr, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_RX_ALARM_CTRL, - rx_alarm_ctrl_val); - - bnx2x_cl45_write(bp, params->port, - ext_phy_type, - ext_phy_addr, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_LASI_CTRL, - lasi_ctrl_val); + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + 0xca13, + &tmp1); bnx2x_cl45_read(bp, params->port, ext_phy_type, @@ -2519,12 +2631,21 @@ static u8 bnx2x_ext_phy_init(struct link_params *params, struct link_vars *vars) /* If this is forced speed, set to KR or KX * (all other are not supported) */ - if (!(params->req_line_speed == SPEED_AUTO_NEG)) { - if (params->req_line_speed == SPEED_10000) { - bnx2x_bcm807x_force_10G(params); - DP(NETIF_MSG_LINK, - "Forced speed 10G on 807X\n"); - break; + if (params->loopback_mode == LOOPBACK_EXT) { + bnx2x_bcm807x_force_10G(params); + DP(NETIF_MSG_LINK, + "Forced speed 10G on 807X\n"); + break; + } else { + bnx2x_cl45_write(bp, params->port, + ext_phy_type, ext_phy_addr, + MDIO_PMA_DEVAD, + MDIO_PMA_REG_BCM_CTRL, + 0x0002); + } + if (params->req_line_speed != SPEED_AUTO_NEG) { + if (params->req_line_speed == SPEED_10000) { + val = (1<<7); } else if (params->req_line_speed == SPEED_2500) { val = (1<<5); @@ -2539,11 +2660,14 @@ static u8 bnx2x_ext_phy_init(struct link_params *params, struct link_vars *vars) PORT_HW_CFG_SPEED_CAPABILITY_D0_10G) val |= (1<<7); + /* Note that 2.5G works only when + used with 1G advertisment */ if (params->speed_cap_mask & - PORT_HW_CFG_SPEED_CAPABILITY_D0_1G) + (PORT_HW_CFG_SPEED_CAPABILITY_D0_1G | + PORT_HW_CFG_SPEED_CAPABILITY_D0_2_5G)) val |= (1<<5); - DP(NETIF_MSG_LINK, "807x autoneg val = 0x%x\n", val); - /*val = ((1<<5)|(1<<7));*/ + DP(NETIF_MSG_LINK, + "807x autoneg val = 0x%x\n", val); } bnx2x_cl45_write(bp, params->port, @@ -2554,20 +2678,19 @@ static u8 bnx2x_ext_phy_init(struct link_params *params, struct link_vars *vars) if (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073) { - /* Disable 2.5Ghz */ + bnx2x_cl45_read(bp, params->port, ext_phy_type, ext_phy_addr, MDIO_AN_DEVAD, 0x8329, &tmp1); -/* SUPPORT_SPEED_CAPABILITY - (Due to the nature of the link order, its not - possible to enable 2.5G within the autoneg - capabilities) - if (params->speed_cap_mask & - PORT_HW_CFG_SPEED_CAPABILITY_D0_2_5G) -*/ - if (params->req_line_speed == SPEED_2500) { + + if (((params->speed_cap_mask & + PORT_HW_CFG_SPEED_CAPABILITY_D0_2_5G) && + (params->req_line_speed == + SPEED_AUTO_NEG)) || + (params->req_line_speed == + SPEED_2500)) { u16 phy_ver; /* Allow 2.5G for A1 and above */ bnx2x_cl45_read(bp, params->port, @@ -2575,49 +2698,53 @@ static u8 bnx2x_ext_phy_init(struct link_params *params, struct link_vars *vars) ext_phy_addr, MDIO_PMA_DEVAD, 0xc801, &phy_ver); - + DP(NETIF_MSG_LINK, "Add 2.5G\n"); if (phy_ver > 0) tmp1 |= 1; else tmp1 &= 0xfffe; - } - else + } else { + DP(NETIF_MSG_LINK, "Disable 2.5G\n"); tmp1 &= 0xfffe; + } - bnx2x_cl45_write(bp, params->port, - ext_phy_type, - ext_phy_addr, - MDIO_AN_DEVAD, + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, 0x8329, tmp1); } - /* Add support for CL37 (passive mode) I */ - bnx2x_cl45_write(bp, params->port, + + /* Add support for CL37 (passive mode) II */ + + bnx2x_cl45_read(bp, params->port, ext_phy_type, ext_phy_addr, MDIO_AN_DEVAD, - MDIO_AN_REG_CL37_CL73, 0x040c); - /* Add support for CL37 (passive mode) II */ + MDIO_AN_REG_CL37_FC_LD, + &tmp1); + bnx2x_cl45_write(bp, params->port, ext_phy_type, ext_phy_addr, MDIO_AN_DEVAD, - MDIO_AN_REG_CL37_FD, 0x20); + MDIO_AN_REG_CL37_FC_LD, (tmp1 | + ((params->req_duplex == DUPLEX_FULL) ? + 0x20 : 0x40))); + /* Add support for CL37 (passive mode) III */ bnx2x_cl45_write(bp, params->port, ext_phy_type, ext_phy_addr, MDIO_AN_DEVAD, MDIO_AN_REG_CL37_AN, 0x1000); - /* Restart autoneg */ - msleep(500); if (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073) { - - /* The SNR will improve about 2db by changing the + /* The SNR will improve about 2db by changing BW and FEE main tap. Rest commands are executed after link is up*/ - /* Change FFE main cursor to 5 in EDC register */ + /*Change FFE main cursor to 5 in EDC register*/ if (bnx2x_8073_is_snr_needed(params)) bnx2x_cl45_write(bp, params->port, ext_phy_type, @@ -2626,25 +2753,28 @@ static u8 bnx2x_ext_phy_init(struct link_params *params, struct link_vars *vars) MDIO_PMA_REG_EDC_FFE_MAIN, 0xFB0C); - /* Enable FEC (Forware Error Correction) - Request in the AN */ - bnx2x_cl45_read(bp, params->port, - ext_phy_type, - ext_phy_addr, - MDIO_AN_DEVAD, - MDIO_AN_REG_ADV2, &tmp1); + /* Enable FEC (Forware Error Correction) + Request in the AN */ + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_ADV2, &tmp1); - tmp1 |= (1<<15); + tmp1 |= (1<<15); + + bnx2x_cl45_write(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + MDIO_AN_REG_ADV2, tmp1); - bnx2x_cl45_write(bp, params->port, - ext_phy_type, - ext_phy_addr, - MDIO_AN_DEVAD, - MDIO_AN_REG_ADV2, tmp1); } bnx2x_ext_phy_set_pause(params, vars); + /* Restart autoneg */ + msleep(500); bnx2x_cl45_write(bp, params->port, ext_phy_type, ext_phy_addr, @@ -2701,10 +2831,7 @@ static u8 bnx2x_ext_phy_init(struct link_params *params, struct link_vars *vars) } } else { /* SerDes */ -/* ext_phy_addr = ((bp->ext_phy_config & - PORT_HW_CFG_SERDES_EXT_PHY_ADDR_MASK) >> - PORT_HW_CFG_SERDES_EXT_PHY_ADDR_SHIFT); -*/ + ext_phy_type = SERDES_EXT_PHY_TYPE(params->ext_phy_config); switch (ext_phy_type) { case PORT_HW_CFG_SERDES_EXT_PHY_TYPE_DIRECT: @@ -2726,7 +2853,7 @@ static u8 bnx2x_ext_phy_init(struct link_params *params, struct link_vars *vars) static u8 bnx2x_ext_phy_is_link_up(struct link_params *params, - struct link_vars *vars) + struct link_vars *vars) { struct bnx2x *bp = params->bp; u32 ext_phy_type; @@ -2767,6 +2894,8 @@ static u8 bnx2x_ext_phy_is_link_up(struct link_params *params, MDIO_PMA_REG_RX_SD, &rx_sd); DP(NETIF_MSG_LINK, "8705 rx_sd 0x%x\n", rx_sd); ext_phy_link_up = (rx_sd & 0x1); + if (ext_phy_link_up) + vars->line_speed = SPEED_10000; break; case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706: @@ -2810,6 +2939,13 @@ static u8 bnx2x_ext_phy_is_link_up(struct link_params *params, */ ext_phy_link_up = ((rx_sd & pcs_status & 0x1) || (val2 & (1<<1))); + if (ext_phy_link_up) { + if (val2 & (1<<1)) + vars->line_speed = SPEED_1000; + else + vars->line_speed = SPEED_10000; + } + /* clear LASI indication*/ bnx2x_cl45_read(bp, params->port, ext_phy_type, ext_phy_addr, @@ -2820,6 +2956,8 @@ static u8 bnx2x_ext_phy_is_link_up(struct link_params *params, case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072: case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073: { + u16 link_status = 0; + u16 an1000_status = 0; if (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072) { bnx2x_cl45_read(bp, params->port, @@ -2846,14 +2984,9 @@ static u8 bnx2x_ext_phy_is_link_up(struct link_params *params, MDIO_PMA_DEVAD, MDIO_PMA_REG_LASI_STATUS, &val1); - bnx2x_cl45_read(bp, params->port, - ext_phy_type, - ext_phy_addr, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_LASI_STATUS, &val2); DP(NETIF_MSG_LINK, - "8703 LASI status 0x%x->0x%x\n", - val1, val2); + "8703 LASI status 0x%x\n", + val1); } /* clear the interrupt LASI status register */ @@ -2869,20 +3002,23 @@ static u8 bnx2x_ext_phy_is_link_up(struct link_params *params, MDIO_PCS_REG_STATUS, &val1); DP(NETIF_MSG_LINK, "807x PCS status 0x%x->0x%x\n", val2, val1); - /* Check the LASI */ + /* Clear MSG-OUT */ bnx2x_cl45_read(bp, params->port, ext_phy_type, ext_phy_addr, MDIO_PMA_DEVAD, - MDIO_PMA_REG_RX_ALARM, &val2); + 0xca13, + &val1); + + /* Check the LASI */ bnx2x_cl45_read(bp, params->port, ext_phy_type, ext_phy_addr, MDIO_PMA_DEVAD, - MDIO_PMA_REG_RX_ALARM, - &val1); - DP(NETIF_MSG_LINK, "KR 0x9003 0x%x->0x%x\n", - val2, val1); + MDIO_PMA_REG_RX_ALARM, &val2); + + DP(NETIF_MSG_LINK, "KR 0x9003 0x%x\n", val2); + /* Check the link status */ bnx2x_cl45_read(bp, params->port, ext_phy_type, @@ -2905,29 +3041,29 @@ static u8 bnx2x_ext_phy_is_link_up(struct link_params *params, DP(NETIF_MSG_LINK, "PMA_REG_STATUS=0x%x\n", val1); if (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073) { - u16 an1000_status = 0; + if (ext_phy_link_up && - ( - (params->req_line_speed != SPEED_10000) - )) { + ((params->req_line_speed != + SPEED_10000))) { if (bnx2x_bcm8073_xaui_wa(params) != 0) { ext_phy_link_up = 0; break; } - bnx2x_cl45_read(bp, params->port, + } + bnx2x_cl45_read(bp, params->port, ext_phy_type, ext_phy_addr, - MDIO_XS_DEVAD, + MDIO_AN_DEVAD, 0x8304, &an1000_status); - bnx2x_cl45_read(bp, params->port, + bnx2x_cl45_read(bp, params->port, ext_phy_type, ext_phy_addr, - MDIO_XS_DEVAD, + MDIO_AN_DEVAD, 0x8304, &an1000_status); - } + /* Check the link status on 1.1.2 */ bnx2x_cl45_read(bp, params->port, ext_phy_type, @@ -2943,8 +3079,8 @@ static u8 bnx2x_ext_phy_is_link_up(struct link_params *params, "an_link_status=0x%x\n", val2, val1, an1000_status); - ext_phy_link_up = (((val1 & 4) == 4) || - (an1000_status & (1<<1))); + ext_phy_link_up = (((val1 & 4) == 4) || + (an1000_status & (1<<1))); if (ext_phy_link_up && bnx2x_8073_is_snr_needed(params)) { /* The SNR will improve about 2dbby @@ -2968,8 +3104,74 @@ static u8 bnx2x_ext_phy_is_link_up(struct link_params *params, MDIO_PMA_REG_CDR_BANDWIDTH, 0x0333); + + } + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_PMA_DEVAD, + 0xc820, + &link_status); + + /* Bits 0..2 --> speed detected, + bits 13..15--> link is down */ + if ((link_status & (1<<2)) && + (!(link_status & (1<<15)))) { + ext_phy_link_up = 1; + vars->line_speed = SPEED_10000; + DP(NETIF_MSG_LINK, + "port %x: External link" + " up in 10G\n", params->port); + } else if ((link_status & (1<<1)) && + (!(link_status & (1<<14)))) { + ext_phy_link_up = 1; + vars->line_speed = SPEED_2500; + DP(NETIF_MSG_LINK, + "port %x: External link" + " up in 2.5G\n", params->port); + } else if ((link_status & (1<<0)) && + (!(link_status & (1<<13)))) { + ext_phy_link_up = 1; + vars->line_speed = SPEED_1000; + DP(NETIF_MSG_LINK, + "port %x: External link" + " up in 1G\n", params->port); + } else { + ext_phy_link_up = 0; + DP(NETIF_MSG_LINK, + "port %x: External link" + " is down\n", params->port); + } + } else { + /* See if 1G link is up for the 8072 */ + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + 0x8304, + &an1000_status); + bnx2x_cl45_read(bp, params->port, + ext_phy_type, + ext_phy_addr, + MDIO_AN_DEVAD, + 0x8304, + &an1000_status); + if (an1000_status & (1<<1)) { + ext_phy_link_up = 1; + vars->line_speed = SPEED_1000; + DP(NETIF_MSG_LINK, + "port %x: External link" + " up in 1G\n", params->port); + } else if (ext_phy_link_up) { + ext_phy_link_up = 1; + vars->line_speed = SPEED_10000; + DP(NETIF_MSG_LINK, + "port %x: External link" + " up in 10G\n", params->port); } } + + break; } case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101: @@ -3006,6 +3208,7 @@ static u8 bnx2x_ext_phy_is_link_up(struct link_params *params, MDIO_AN_DEVAD, MDIO_AN_REG_MASTER_STATUS, &val2); + vars->line_speed = SPEED_10000; DP(NETIF_MSG_LINK, "SFX7101 AN status 0x%x->Master=%x\n", val2, @@ -3100,7 +3303,7 @@ static void bnx2x_link_int_enable(struct link_params *params) * link management */ static void bnx2x_link_int_ack(struct link_params *params, - struct link_vars *vars, u16 is_10g) + struct link_vars *vars, u8 is_10g) { struct bnx2x *bp = params->bp; u8 port = params->port; @@ -3181,7 +3384,8 @@ static u8 bnx2x_format_ver(u32 num, u8 *str, u16 len) } -static void bnx2x_turn_on_sf(struct bnx2x *bp, u8 port, u8 ext_phy_addr) +static void bnx2x_turn_on_ef(struct bnx2x *bp, u8 port, u8 ext_phy_addr, + u32 ext_phy_type) { u32 cnt = 0; u16 ctrl = 0; @@ -3192,12 +3396,14 @@ static void bnx2x_turn_on_sf(struct bnx2x *bp, u8 port, u8 ext_phy_addr) /* take ext phy out of reset */ bnx2x_set_gpio(bp, - MISC_REGISTERS_GPIO_2, - MISC_REGISTERS_GPIO_HIGH); + MISC_REGISTERS_GPIO_2, + MISC_REGISTERS_GPIO_HIGH, + port); bnx2x_set_gpio(bp, - MISC_REGISTERS_GPIO_1, - MISC_REGISTERS_GPIO_HIGH); + MISC_REGISTERS_GPIO_1, + MISC_REGISTERS_GPIO_HIGH, + port); /* wait for 5ms */ msleep(5); @@ -3205,7 +3411,7 @@ static void bnx2x_turn_on_sf(struct bnx2x *bp, u8 port, u8 ext_phy_addr) for (cnt = 0; cnt < 1000; cnt++) { msleep(1); bnx2x_cl45_read(bp, port, - PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101, + ext_phy_type, ext_phy_addr, MDIO_PMA_DEVAD, MDIO_PMA_REG_CTRL, @@ -3217,13 +3423,17 @@ static void bnx2x_turn_on_sf(struct bnx2x *bp, u8 port, u8 ext_phy_addr) } } -static void bnx2x_turn_off_sf(struct bnx2x *bp) +static void bnx2x_turn_off_sf(struct bnx2x *bp, u8 port) { /* put sf to reset */ - bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1, MISC_REGISTERS_GPIO_LOW); bnx2x_set_gpio(bp, - MISC_REGISTERS_GPIO_2, - MISC_REGISTERS_GPIO_LOW); + MISC_REGISTERS_GPIO_1, + MISC_REGISTERS_GPIO_LOW, + port); + bnx2x_set_gpio(bp, + MISC_REGISTERS_GPIO_2, + MISC_REGISTERS_GPIO_LOW, + port); } u8 bnx2x_get_ext_phy_fw_version(struct link_params *params, u8 driver_loaded, @@ -3253,7 +3463,8 @@ u8 bnx2x_get_ext_phy_fw_version(struct link_params *params, u8 driver_loaded, /* Take ext phy out of reset */ if (!driver_loaded) - bnx2x_turn_on_sf(bp, params->port, ext_phy_addr); + bnx2x_turn_on_ef(bp, params->port, ext_phy_addr, + ext_phy_type); /* wait for 1ms */ msleep(1); @@ -3276,11 +3487,16 @@ u8 bnx2x_get_ext_phy_fw_version(struct link_params *params, u8 driver_loaded, version[4] = '\0'; if (!driver_loaded) - bnx2x_turn_off_sf(bp); + bnx2x_turn_off_sf(bp, params->port); break; case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072: case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073: { + /* Take ext phy out of reset */ + if (!driver_loaded) + bnx2x_turn_on_ef(bp, params->port, ext_phy_addr, + ext_phy_type); + bnx2x_cl45_read(bp, params->port, ext_phy_type, ext_phy_addr, MDIO_PMA_DEVAD, @@ -3333,7 +3549,7 @@ static void bnx2x_set_xgxs_loopback(struct link_params *params, struct bnx2x *bp = params->bp; if (is_10g) { - u32 md_devad; + u32 md_devad; DP(NETIF_MSG_LINK, "XGXS 10G loopback enable\n"); @@ -3553,6 +3769,8 @@ u8 bnx2x_set_led(struct bnx2x *bp, u8 port, u8 mode, u32 speed, u16 hw_led_mode, u32 chip_id) { u8 rc = 0; + u32 tmp; + u32 emac_base = port ? GRCBASE_EMAC1 : GRCBASE_EMAC0; DP(NETIF_MSG_LINK, "bnx2x_set_led: port %x, mode %d\n", port, mode); DP(NETIF_MSG_LINK, "speed 0x%x, hw_led_mode 0x%x\n", speed, hw_led_mode); @@ -3561,6 +3779,9 @@ u8 bnx2x_set_led(struct bnx2x *bp, u8 port, u8 mode, u32 speed, REG_WR(bp, NIG_REG_LED_10G_P0 + port*4, 0); REG_WR(bp, NIG_REG_LED_MODE_P0 + port*4, SHARED_HW_CFG_LED_MAC1); + + tmp = EMAC_RD(bp, EMAC_REG_EMAC_LED); + EMAC_WR(bp, EMAC_REG_EMAC_LED, (tmp | EMAC_LED_OVERRIDE)); break; case LED_MODE_OPER: @@ -3572,6 +3793,10 @@ u8 bnx2x_set_led(struct bnx2x *bp, u8 port, u8 mode, u32 speed, LED_BLINK_RATE_VAL); REG_WR(bp, NIG_REG_LED_CONTROL_BLINK_RATE_ENA_P0 + port*4, 1); + tmp = EMAC_RD(bp, EMAC_REG_EMAC_LED); + EMAC_WR(bp, EMAC_REG_EMAC_LED, + (tmp & (~EMAC_LED_OVERRIDE))); + if (!CHIP_IS_E1H(bp) && ((speed == SPEED_2500) || (speed == SPEED_1000) || @@ -3622,7 +3847,8 @@ static u8 bnx2x_link_initialize(struct link_params *params, struct bnx2x *bp = params->bp; u8 port = params->port; u8 rc = 0; - + u8 non_ext_phy; + u32 ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config); /* Activate the external PHY */ bnx2x_ext_phy_reset(params, vars); @@ -3644,10 +3870,6 @@ static u8 bnx2x_link_initialize(struct link_params *params, bnx2x_set_swap_lanes(params); } - /* Set Parallel Detect */ - if (params->req_line_speed == SPEED_AUTO_NEG) - bnx2x_set_parallel_detection(params, vars->phy_flags); - if (vars->phy_flags & PHY_XGXS_FLAG) { if (params->req_line_speed && ((params->req_line_speed == SPEED_100) || @@ -3657,68 +3879,33 @@ static u8 bnx2x_link_initialize(struct link_params *params, vars->phy_flags &= ~PHY_SGMII_FLAG; } } + /* In case of external phy existance, the line speed would be the + line speed linked up by the external phy. In case it is direct only, + then the line_speed during initialization will be equal to the + req_line_speed*/ + vars->line_speed = params->req_line_speed; - if (!(vars->phy_flags & PHY_SGMII_FLAG)) { - u16 bank, rx_eq; - - rx_eq = ((params->serdes_config & - PORT_HW_CFG_SERDES_RX_DRV_EQUALIZER_MASK) >> - PORT_HW_CFG_SERDES_RX_DRV_EQUALIZER_SHIFT); + bnx2x_calc_ieee_aneg_adv(params, &vars->ieee_fc); - DP(NETIF_MSG_LINK, "setting rx eq to 0x%x\n", rx_eq); - for (bank = MDIO_REG_BANK_RX0; bank <= MDIO_REG_BANK_RX_ALL; - bank += (MDIO_REG_BANK_RX1-MDIO_REG_BANK_RX0)) { - CL45_WR_OVER_CL22(bp, port, - params->phy_addr, - bank , - MDIO_RX0_RX_EQ_BOOST, - ((rx_eq & - MDIO_RX0_RX_EQ_BOOST_EQUALIZER_CTRL_MASK) | - MDIO_RX0_RX_EQ_BOOST_OFFSET_CTRL)); - } - - /* forced speed requested? */ - if (params->req_line_speed != SPEED_AUTO_NEG) { - DP(NETIF_MSG_LINK, "not SGMII, no AN\n"); - - /* disable autoneg */ - bnx2x_set_autoneg(params, vars); - - /* program speed and duplex */ - bnx2x_program_serdes(params); - vars->ieee_fc = - MDIO_COMBO_IEEE0_AUTO_NEG_ADV_PAUSE_NONE; - - } else { /* AN_mode */ - DP(NETIF_MSG_LINK, "not SGMII, AN\n"); - - /* AN enabled */ - bnx2x_set_brcm_cl37_advertisment(params); - - /* program duplex & pause advertisement (for aneg) */ - bnx2x_set_ieee_aneg_advertisment(params, - &vars->ieee_fc); - - /* enable autoneg */ - bnx2x_set_autoneg(params, vars); - - /* enable and restart AN */ - bnx2x_restart_autoneg(params); - } - - } else { /* SGMII mode */ - DP(NETIF_MSG_LINK, "SGMII\n"); - - bnx2x_initialize_sgmii_process(params); + /* init ext phy and enable link state int */ + non_ext_phy = ((ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) || + (params->loopback_mode == LOOPBACK_XGXS_10) || + (params->loopback_mode == LOOPBACK_EXT_PHY)); + + if (non_ext_phy || + (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705)) { + if (params->req_line_speed == SPEED_AUTO_NEG) + bnx2x_set_parallel_detection(params, vars->phy_flags); + bnx2x_init_internal_phy(params, vars); } - /* init ext phy and enable link state int */ - rc |= bnx2x_ext_phy_init(params, vars); + if (!non_ext_phy) + rc |= bnx2x_ext_phy_init(params, vars); bnx2x_bits_dis(bp, NIG_REG_STATUS_INTERRUPT_PORT0 + port*4, - (NIG_STATUS_XGXS0_LINK10G | - NIG_STATUS_XGXS0_LINK_STATUS | - NIG_STATUS_SERDES0_LINK_STATUS)); + (NIG_STATUS_XGXS0_LINK10G | + NIG_STATUS_XGXS0_LINK_STATUS | + NIG_STATUS_SERDES0_LINK_STATUS)); return rc; @@ -3730,15 +3917,23 @@ u8 bnx2x_phy_init(struct link_params *params, struct link_vars *vars) struct bnx2x *bp = params->bp; u32 val; - DP(NETIF_MSG_LINK, "Phy Initialization started\n"); + DP(NETIF_MSG_LINK, "Phy Initialization started \n"); DP(NETIF_MSG_LINK, "req_speed = %d, req_flowctrl=%d\n", params->req_line_speed, params->req_flow_ctrl); vars->link_status = 0; + vars->phy_link_up = 0; + vars->link_up = 0; + vars->line_speed = 0; + vars->duplex = DUPLEX_FULL; + vars->flow_ctrl = FLOW_CTRL_NONE; + vars->mac_type = MAC_TYPE_NONE; + if (params->switch_cfg == SWITCH_CFG_1G) vars->phy_flags = PHY_SERDES_FLAG; else vars->phy_flags = PHY_XGXS_FLAG; + /* disable attentions */ bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 + params->port*4, (NIG_MASK_XGXS0_LINK_STATUS | @@ -3894,6 +4089,7 @@ u8 bnx2x_phy_init(struct link_params *params, struct link_vars *vars) } bnx2x_link_initialize(params, vars); + msleep(30); bnx2x_link_int_enable(params); } return 0; @@ -3943,39 +4139,22 @@ u8 bnx2x_link_reset(struct link_params *params, struct link_vars *vars) /* HW reset */ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1, - MISC_REGISTERS_GPIO_OUTPUT_LOW); + MISC_REGISTERS_GPIO_OUTPUT_LOW, + port); bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, - MISC_REGISTERS_GPIO_OUTPUT_LOW); + MISC_REGISTERS_GPIO_OUTPUT_LOW, + port); DP(NETIF_MSG_LINK, "reset external PHY\n"); - } else { - - u8 ext_phy_addr = ((ext_phy_config & - PORT_HW_CFG_XGXS_EXT_PHY_ADDR_MASK) >> - PORT_HW_CFG_XGXS_EXT_PHY_ADDR_SHIFT); - - /* SW reset */ - bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_CTRL, - 1<<15); - - /* Set Low Power Mode */ - bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr, - MDIO_PMA_DEVAD, - MDIO_PMA_REG_CTRL, - 1<<11); - - - if (ext_phy_type == - PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073) { - DP(NETIF_MSG_LINK, "Setting 8073 port %d into" + } else if (ext_phy_type == + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073) { + DP(NETIF_MSG_LINK, "Setting 8073 port %d into " "low power mode\n", port); bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, - MISC_REGISTERS_GPIO_OUTPUT_LOW); - } + MISC_REGISTERS_GPIO_OUTPUT_LOW, + port); } } /* reset the SerDes/XGXS */ @@ -3995,6 +4174,73 @@ u8 bnx2x_link_reset(struct link_params *params, struct link_vars *vars) return 0; } +static u8 bnx2x_update_link_down(struct link_params *params, + struct link_vars *vars) +{ + struct bnx2x *bp = params->bp; + u8 port = params->port; + DP(NETIF_MSG_LINK, "Port %x: Link is down\n", port); + bnx2x_set_led(bp, port, LED_MODE_OFF, + 0, params->hw_led_mode, + params->chip_id); + + /* indicate no mac active */ + vars->mac_type = MAC_TYPE_NONE; + + /* update shared memory */ + vars->link_status = 0; + vars->line_speed = 0; + bnx2x_update_mng(params, vars->link_status); + + /* activate nig drain */ + REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + port*4, 1); + + /* reset BigMac */ + bnx2x_bmac_rx_disable(bp, params->port); + REG_WR(bp, GRCBASE_MISC + + MISC_REGISTERS_RESET_REG_2_CLEAR, + (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port)); + return 0; +} + +static u8 bnx2x_update_link_up(struct link_params *params, + struct link_vars *vars, + u8 link_10g, u32 gp_status) +{ + struct bnx2x *bp = params->bp; + u8 port = params->port; + u8 rc = 0; + vars->link_status |= LINK_STATUS_LINK_UP; + if (link_10g) { + bnx2x_bmac_enable(params, vars, 0); + bnx2x_set_led(bp, port, LED_MODE_OPER, + SPEED_10000, params->hw_led_mode, + params->chip_id); + + } else { + bnx2x_emac_enable(params, vars, 0); + rc = bnx2x_emac_program(params, vars->line_speed, + vars->duplex); + + /* AN complete? */ + if (gp_status & MDIO_AN_CL73_OR_37_COMPLETE) { + if (!(vars->phy_flags & + PHY_SGMII_FLAG)) + bnx2x_set_sgmii_tx_driver(params); + } + } + + /* PBF - link up */ + rc |= bnx2x_pbf_update(params, vars->flow_ctrl, + vars->line_speed); + + /* disable drain */ + REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + port*4, 0); + + /* update shared memory */ + bnx2x_update_mng(params, vars->link_status); + return rc; +} /* This function should called upon link interrupt */ /* In case vars->link_up, driver needs to 1. Update the pbf @@ -4012,10 +4258,10 @@ u8 bnx2x_link_update(struct link_params *params, struct link_vars *vars) { struct bnx2x *bp = params->bp; u8 port = params->port; - u16 i; u16 gp_status; - u16 link_10g; - u8 rc = 0; + u8 link_10g; + u8 ext_phy_link_up, rc = 0; + u32 ext_phy_type; DP(NETIF_MSG_LINK, "port %x, XGXS?%x, int_status 0x%x\n", port, @@ -4031,15 +4277,16 @@ u8 bnx2x_link_update(struct link_params *params, struct link_vars *vars) REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK10G + port*0x68), REG_RD(bp, NIG_REG_XGXS0_STATUS_LINK_STATUS + port*0x68)); + ext_phy_type = XGXS_EXT_PHY_TYPE(params->ext_phy_config); - /* avoid fast toggling */ - for (i = 0; i < 10; i++) { - msleep(10); - CL45_RD_OVER_CL22(bp, port, params->phy_addr, - MDIO_REG_BANK_GP_STATUS, - MDIO_GP_STATUS_TOP_AN_STATUS1, - &gp_status); - } + /* Check external link change only for non-direct */ + ext_phy_link_up = bnx2x_ext_phy_is_link_up(params, vars); + + /* Read gp_status */ + CL45_RD_OVER_CL22(bp, port, params->phy_addr, + MDIO_REG_BANK_GP_STATUS, + MDIO_GP_STATUS_TOP_AN_STATUS1, + &gp_status); rc = bnx2x_link_settings_status(params, vars, gp_status); if (rc != 0) @@ -4055,73 +4302,177 @@ u8 bnx2x_link_update(struct link_params *params, struct link_vars *vars) bnx2x_link_int_ack(params, vars, link_10g); + /* In case external phy link is up, and internal link is down + ( not initialized yet probably after link initialization, it needs + to be initialized. + Note that after link down-up as result of cable plug, + the xgxs link would probably become up again without the need to + initialize it*/ + + if ((ext_phy_type != PORT_HW_CFG_SERDES_EXT_PHY_TYPE_DIRECT) && + (ext_phy_type != PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705) && + (ext_phy_link_up && !vars->phy_link_up)) + bnx2x_init_internal_phy(params, vars); + /* link is up only if both local phy and external phy are up */ - vars->link_up = (vars->phy_link_up && - bnx2x_ext_phy_is_link_up(params, vars)); + vars->link_up = (ext_phy_link_up && vars->phy_link_up); - if (!vars->phy_link_up && - REG_RD(bp, NIG_REG_EMAC0_STATUS_MISC_MI_INT + port*0x18)) { - bnx2x_ext_phy_is_link_up(params, vars); /* Clear interrupt */ + if (vars->link_up) + rc = bnx2x_update_link_up(params, vars, link_10g, gp_status); + else + rc = bnx2x_update_link_down(params, vars); + + return rc; +} + +static u8 bnx2x_8073_common_init_phy(struct bnx2x *bp, u32 shmem_base) +{ + u8 ext_phy_addr[PORT_MAX]; + u16 val; + s8 port; + + /* PART1 - Reset both phys */ + for (port = PORT_MAX - 1; port >= PORT_0; port--) { + /* Extract the ext phy address for the port */ + u32 ext_phy_config = REG_RD(bp, shmem_base + + offsetof(struct shmem_region, + dev_info.port_hw_config[port].external_phy_config)); + + /* disable attentions */ + bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port*4, + (NIG_MASK_XGXS0_LINK_STATUS | + NIG_MASK_XGXS0_LINK10G | + NIG_MASK_SERDES0_LINK_STATUS | + NIG_MASK_MI_INT)); + + ext_phy_addr[port] = + ((ext_phy_config & + PORT_HW_CFG_XGXS_EXT_PHY_ADDR_MASK) >> + PORT_HW_CFG_XGXS_EXT_PHY_ADDR_SHIFT); + + /* Need to take the phy out of low power mode in order + to write to access its registers */ + bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, + MISC_REGISTERS_GPIO_OUTPUT_HIGH, port); + + /* Reset the phy */ + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr[port], + MDIO_PMA_DEVAD, + MDIO_PMA_REG_CTRL, + 1<<15); } - if (vars->link_up) { - vars->link_status |= LINK_STATUS_LINK_UP; - if (link_10g) { - bnx2x_bmac_enable(params, vars, 0); - bnx2x_set_led(bp, port, LED_MODE_OPER, - SPEED_10000, params->hw_led_mode, - params->chip_id); + /* Add delay of 150ms after reset */ + msleep(150); - } else { - bnx2x_emac_enable(params, vars, 0); - rc = bnx2x_emac_program(params, vars->line_speed, - vars->duplex); + /* PART2 - Download firmware to both phys */ + for (port = PORT_MAX - 1; port >= PORT_0; port--) { + u16 fw_ver1; - /* AN complete? */ - if (gp_status & MDIO_AN_CL73_OR_37_COMPLETE) { - if (!(vars->phy_flags & - PHY_SGMII_FLAG)) - bnx2x_set_sgmii_tx_driver(params); - } + bnx2x_bcm8073_external_rom_boot(bp, port, + ext_phy_addr[port]); + + bnx2x_cl45_read(bp, port, PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr[port], + MDIO_PMA_DEVAD, + MDIO_PMA_REG_ROM_VER1, &fw_ver1); + if (fw_ver1 == 0) { + DP(NETIF_MSG_LINK, + "bnx2x_8073_common_init_phy port %x " + "fw Download failed\n", port); + return -EINVAL; } - /* PBF - link up */ - rc |= bnx2x_pbf_update(params, vars->flow_ctrl, - vars->line_speed); + /* Only set bit 10 = 1 (Tx power down) */ + bnx2x_cl45_read(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr[port], + MDIO_PMA_DEVAD, + MDIO_PMA_REG_TX_POWER_DOWN, &val); - /* disable drain */ - REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + port*4, 0); + /* Phase1 of TX_POWER_DOWN reset */ + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr[port], + MDIO_PMA_DEVAD, + MDIO_PMA_REG_TX_POWER_DOWN, + (val | 1<<10)); + } - /* update shared memory */ - bnx2x_update_mng(params, vars->link_status); + /* Toggle Transmitter: Power down and then up with 600ms + delay between */ + msleep(600); - } else { /* link down */ - DP(NETIF_MSG_LINK, "Port %x: Link is down\n", params->port); - bnx2x_set_led(bp, port, LED_MODE_OFF, - 0, params->hw_led_mode, - params->chip_id); + /* PART3 - complete TX_POWER_DOWN process, and set GPIO2 back to low */ + for (port = PORT_MAX - 1; port >= PORT_0; port--) { + /* Phase2 of POWER_DOWN_RESET*/ + /* Release bit 10 (Release Tx power down) */ + bnx2x_cl45_read(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr[port], + MDIO_PMA_DEVAD, + MDIO_PMA_REG_TX_POWER_DOWN, &val); - /* indicate no mac active */ - vars->mac_type = MAC_TYPE_NONE; + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr[port], + MDIO_PMA_DEVAD, + MDIO_PMA_REG_TX_POWER_DOWN, (val & (~(1<<10)))); + msleep(15); - /* update shared memory */ - vars->link_status = 0; - bnx2x_update_mng(params, vars->link_status); + /* Read modify write the SPI-ROM version select register */ + bnx2x_cl45_read(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr[port], + MDIO_PMA_DEVAD, + MDIO_PMA_REG_EDC_FFE_MAIN, &val); + bnx2x_cl45_write(bp, port, + PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073, + ext_phy_addr[port], + MDIO_PMA_DEVAD, + MDIO_PMA_REG_EDC_FFE_MAIN, (val | (1<<12))); - /* activate nig drain */ - REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + port*4, 1); + /* set GPIO2 back to LOW */ + bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2, + MISC_REGISTERS_GPIO_OUTPUT_LOW, port); + } + return 0; - /* reset BigMac */ - bnx2x_bmac_rx_disable(bp, params->port); - REG_WR(bp, GRCBASE_MISC + - MISC_REGISTERS_RESET_REG_2_CLEAR, - (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port)); +} +u8 bnx2x_common_init_phy(struct bnx2x *bp, u32 shmem_base) +{ + u8 rc = 0; + u32 ext_phy_type; + + DP(NETIF_MSG_LINK, "bnx2x_common_init_phy\n"); + + /* Read the ext_phy_type for arbitrary port(0) */ + ext_phy_type = XGXS_EXT_PHY_TYPE( + REG_RD(bp, shmem_base + + offsetof(struct shmem_region, + dev_info.port_hw_config[0].external_phy_config))); + + switch (ext_phy_type) { + case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073: + { + rc = bnx2x_8073_common_init_phy(bp, shmem_base); + break; + } + default: + DP(NETIF_MSG_LINK, + "bnx2x_common_init_phy: ext_phy 0x%x not required\n", + ext_phy_type); + break; } return rc; } + + static void bnx2x_sfx7101_sp_sw_reset(struct bnx2x *bp, u8 port, u8 phy_addr) { u16 val, cnt; @@ -4154,7 +4505,7 @@ static void bnx2x_sfx7101_sp_sw_reset(struct bnx2x *bp, u8 port, u8 phy_addr) } #define RESERVED_SIZE 256 /* max application is 160K bytes - data at end of RAM */ -#define MAX_APP_SIZE 160*1024 - RESERVED_SIZE +#define MAX_APP_SIZE (160*1024 - RESERVED_SIZE) /* Header is 14 bytes */ #define HEADER_SIZE 14 @@ -4192,12 +4543,12 @@ static u8 bnx2x_sfx7101_flash_download(struct bnx2x *bp, u8 port, size = MAX_APP_SIZE+HEADER_SIZE; } DP(NETIF_MSG_LINK, "File version is %c%c\n", data[0x14e], data[0x14f]); - DP(NETIF_MSG_LINK, " %c%c\n", data[0x150], data[0x151]); + DP(NETIF_MSG_LINK, " %c%c\n", data[0x150], data[0x151]); /* Put the DSP in download mode by setting FLASH_CFG[2] to 1 and issuing a reset.*/ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_0, - MISC_REGISTERS_GPIO_HIGH); + MISC_REGISTERS_GPIO_HIGH, port); bnx2x_sfx7101_sp_sw_reset(bp, port, ext_phy_addr); @@ -4429,7 +4780,8 @@ static u8 bnx2x_sfx7101_flash_download(struct bnx2x *bp, u8 port, } /* DSP Remove Download Mode */ - bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_0, MISC_REGISTERS_GPIO_LOW); + bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_0, + MISC_REGISTERS_GPIO_LOW, port); bnx2x_sfx7101_sp_sw_reset(bp, port, ext_phy_addr); @@ -4437,7 +4789,7 @@ static u8 bnx2x_sfx7101_flash_download(struct bnx2x *bp, u8 port, for (cnt = 0; cnt < 100; cnt++) msleep(5); - bnx2x_hw_reset(bp); + bnx2x_hw_reset(bp, port); for (cnt = 0; cnt < 100; cnt++) msleep(5); @@ -4473,7 +4825,7 @@ static u8 bnx2x_sfx7101_flash_download(struct bnx2x *bp, u8 port, MDIO_PMA_REG_7101_VER2, &image_revision2); - if (data[0x14e] != (image_revision2&0xFF) || + if (data[0x14e] != (image_revision2&0xFF) || data[0x14f] != ((image_revision2&0xFF00)>>8) || data[0x150] != (image_revision1&0xFF) || data[0x151] != ((image_revision1&0xFF00)>>8)) { @@ -4508,11 +4860,11 @@ u8 bnx2x_flash_download(struct bnx2x *bp, u8 port, u32 ext_phy_config, case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101: /* Take ext phy out of reset */ if (!driver_loaded) - bnx2x_turn_on_sf(bp, port, ext_phy_addr); + bnx2x_turn_on_ef(bp, port, ext_phy_addr, ext_phy_type); rc = bnx2x_sfx7101_flash_download(bp, port, ext_phy_addr, data, size); if (!driver_loaded) - bnx2x_turn_off_sf(bp); + bnx2x_turn_off_sf(bp, port); break; case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT: case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE: |