diff options
Diffstat (limited to 'drivers/net/can/Kconfig')
| -rw-r--r-- | drivers/net/can/Kconfig | 38 |
1 files changed, 24 insertions, 14 deletions
diff --git a/drivers/net/can/Kconfig b/drivers/net/can/Kconfig index b56bd9e8095..9862b2e0764 100644 --- a/drivers/net/can/Kconfig +++ b/drivers/net/can/Kconfig @@ -1,9 +1,7 @@ menu "CAN Device Drivers" - depends on CAN config CAN_VCAN tristate "Virtual Local CAN Interface (vcan)" - depends on CAN ---help--- Similar to the network loopback devices, vcan offers a virtual local CAN interface. @@ -13,7 +11,7 @@ config CAN_VCAN config CAN_SLCAN tristate "Serial / USB serial CAN Adaptors (slcan)" - depends on CAN + depends on TTY ---help--- CAN driver for several 'low cost' CAN interfaces that are attached via serial lines or via USB-to-serial adapters using the LAWICEL @@ -33,16 +31,16 @@ config CAN_SLCAN config CAN_DEV tristate "Platform CAN drivers with Netlink support" - depends on CAN default y ---help--- Enables the common framework for platform CAN drivers with Netlink support. This is the standard library for CAN drivers. If unsure, say Y. +if CAN_DEV + config CAN_CALC_BITTIMING bool "CAN bit-timing calculation" - depends on CAN_DEV default y ---help--- If enabled, CAN bit-timing parameters will be calculated for the @@ -54,15 +52,26 @@ config CAN_CALC_BITTIMING arguments "tq", "prop_seg", "phase_seg1", "phase_seg2" and "sjw". If unsure, say Y. +config CAN_LEDS + bool "Enable LED triggers for Netlink based drivers" + depends on LEDS_CLASS + select LEDS_TRIGGERS + ---help--- + This option adds two LED triggers for packet receive and transmit + events on each supported CAN device. + + Say Y here if you are working on a system with led-class supported + LEDs and you want to use them as canbus activity indicators. + config CAN_AT91 tristate "Atmel AT91 onchip CAN controller" - depends on CAN_DEV && (ARCH_AT91SAM9263 || ARCH_AT91SAM9X5) + depends on ARCH_AT91SAM9263 || ARCH_AT91SAM9X5 ---help--- This is a driver for the SoC CAN controller in Atmel's AT91SAM9263 and AT91SAM9X5 processors. config CAN_TI_HECC - depends on CAN_DEV && ARCH_OMAP3 + depends on ARCH_OMAP3 tristate "TI High End CAN Controller" ---help--- Driver for TI HECC (High End CAN Controller) module found on many @@ -70,12 +79,12 @@ config CAN_TI_HECC config CAN_MCP251X tristate "Microchip MCP251x SPI CAN controllers" - depends on CAN_DEV && SPI && HAS_DMA + depends on SPI && HAS_DMA ---help--- Driver for the Microchip MCP251x SPI CAN controllers. config CAN_BFIN - depends on CAN_DEV && (BF534 || BF536 || BF537 || BF538 || BF539 || BF54x) + depends on BF534 || BF536 || BF537 || BF538 || BF539 || BF54x tristate "Analog Devices Blackfin on-chip CAN" ---help--- Driver for the Analog Devices Blackfin on-chip CAN controllers @@ -85,7 +94,7 @@ config CAN_BFIN config CAN_JANZ_ICAN3 tristate "Janz VMOD-ICAN3 Intelligent CAN controller" - depends on CAN_DEV && MFD_JANZ_CMODIO + depends on MFD_JANZ_CMODIO ---help--- Driver for Janz VMOD-ICAN3 Intelligent CAN controller module, which connects to a MODULbus carrier board. @@ -98,13 +107,13 @@ config HAVE_CAN_FLEXCAN config CAN_FLEXCAN tristate "Support for Freescale FLEXCAN based chips" - depends on CAN_DEV && HAVE_CAN_FLEXCAN + depends on HAVE_CAN_FLEXCAN ---help--- Say Y here if you want to support for Freescale FlexCAN. config PCH_CAN tristate "Intel EG20T PCH CAN controller" - depends on CAN_DEV && PCI + depends on PCI ---help--- This driver is for PCH CAN of Topcliff (Intel EG20T PCH) which is an IOH for x86 embedded processor (Intel Atom E6xx series). @@ -112,7 +121,7 @@ config PCH_CAN config CAN_GRCAN tristate "Aeroflex Gaisler GRCAN and GRHCAN CAN devices" - depends on CAN_DEV && OF + depends on OF ---help--- Say Y here if you want to use Aeroflex Gaisler GRCAN or GRHCAN. Note that the driver supports little endian, even though little @@ -131,9 +140,10 @@ source "drivers/net/can/usb/Kconfig" source "drivers/net/can/softing/Kconfig" +endif + config CAN_DEBUG_DEVICES bool "CAN devices debugging messages" - depends on CAN ---help--- Say Y here if you want the CAN device drivers to produce a bunch of debug messages to the system log. Select this if you are having |