diff options
Diffstat (limited to 'drivers/net/de600.h')
| -rw-r--r-- | drivers/net/de600.h | 169 |
1 files changed, 169 insertions, 0 deletions
diff --git a/drivers/net/de600.h b/drivers/net/de600.h new file mode 100644 index 00000000000..e4073015dcd --- /dev/null +++ b/drivers/net/de600.h @@ -0,0 +1,169 @@ +/************************************************** + * * + * Definition of D-Link Ethernet Pocket adapter * + * * + **************************************************/ +/* + * D-Link Ethernet pocket adapter ports + */ +/* + * OK, so I'm cheating, but there are an awful lot of + * reads and writes in order to get anything in and out + * of the DE-600 with 4 bits at a time in the parallel port, + * so every saved instruction really helps :-) + */ + +#ifndef DE600_IO +#define DE600_IO 0x378 +#endif + +#define DATA_PORT (DE600_IO) +#define STATUS_PORT (DE600_IO + 1) +#define COMMAND_PORT (DE600_IO + 2) + +#ifndef DE600_IRQ +#define DE600_IRQ 7 +#endif +/* + * It really should look like this, and autoprobing as well... + * +#define DATA_PORT (dev->base_addr + 0) +#define STATUS_PORT (dev->base_addr + 1) +#define COMMAND_PORT (dev->base_addr + 2) +#define DE600_IRQ dev->irq + */ + +/* + * D-Link COMMAND_PORT commands + */ +#define SELECT_NIC 0x04 /* select Network Interface Card */ +#define SELECT_PRN 0x1c /* select Printer */ +#define NML_PRN 0xec /* normal Printer situation */ +#define IRQEN 0x10 /* enable IRQ line */ + +/* + * D-Link STATUS_PORT + */ +#define RX_BUSY 0x80 +#define RX_GOOD 0x40 +#define TX_FAILED16 0x10 +#define TX_BUSY 0x08 + +/* + * D-Link DATA_PORT commands + * command in low 4 bits + * data in high 4 bits + * select current data nibble with HI_NIBBLE bit + */ +#define WRITE_DATA 0x00 /* write memory */ +#define READ_DATA 0x01 /* read memory */ +#define STATUS 0x02 /* read status register */ +#define COMMAND 0x03 /* write command register (see COMMAND below) */ +#define NULL_COMMAND 0x04 /* null command */ +#define RX_LEN 0x05 /* read received packet length */ +#define TX_ADDR 0x06 /* set adapter transmit memory address */ +#define RW_ADDR 0x07 /* set adapter read/write memory address */ +#define HI_NIBBLE 0x08 /* read/write the high nibble of data, + or-ed with rest of command */ + +/* + * command register, accessed through DATA_PORT with low bits = COMMAND + */ +#define RX_ALL 0x01 /* PROMISCUOUS */ +#define RX_BP 0x02 /* default: BROADCAST & PHYSICAL ADDRESS */ +#define RX_MBP 0x03 /* MULTICAST, BROADCAST & PHYSICAL ADDRESS */ + +#define TX_ENABLE 0x04 /* bit 2 */ +#define RX_ENABLE 0x08 /* bit 3 */ + +#define RESET 0x80 /* set bit 7 high */ +#define STOP_RESET 0x00 /* set bit 7 low */ + +/* + * data to command register + * (high 4 bits in write to DATA_PORT) + */ +#define RX_PAGE2_SELECT 0x10 /* bit 4, only 2 pages to select */ +#define RX_BASE_PAGE 0x20 /* bit 5, always set when specifying RX_ADDR */ +#define FLIP_IRQ 0x40 /* bit 6 */ + +/* + * D-Link adapter internal memory: + * + * 0-2K 1:st transmit page (send from pointer up to 2K) + * 2-4K 2:nd transmit page (send from pointer up to 4K) + * + * 4-6K 1:st receive page (data from 4K upwards) + * 6-8K 2:nd receive page (data from 6K upwards) + * + * 8K+ Adapter ROM (contains magic code and last 3 bytes of Ethernet address) + */ +#define MEM_2K 0x0800 /* 2048 */ +#define MEM_4K 0x1000 /* 4096 */ +#define MEM_6K 0x1800 /* 6144 */ +#define NODE_ADDRESS 0x2000 /* 8192 */ + +#define RUNT 60 /* Too small Ethernet packet */ + +/************************************************** + * * + * End of definition * + * * + **************************************************/ + +/* + * Index to functions, as function prototypes. + */ +/* Routines used internally. (See "convenience macros") */ +static u8 de600_read_status(struct net_device *dev); +static u8 de600_read_byte(unsigned char type, struct net_device *dev); + +/* Put in the device structure. */ +static int de600_open(struct net_device *dev); +static int de600_close(struct net_device *dev); +static struct net_device_stats *get_stats(struct net_device *dev); +static int de600_start_xmit(struct sk_buff *skb, struct net_device *dev); + +/* Dispatch from interrupts. */ +static irqreturn_t de600_interrupt(int irq, void *dev_id, struct pt_regs *regs); +static int de600_tx_intr(struct net_device *dev, int irq_status); +static void de600_rx_intr(struct net_device *dev); + +/* Initialization */ +static void trigger_interrupt(struct net_device *dev); +static int adapter_init(struct net_device *dev); + +/* + * Convenience macros/functions for D-Link adapter + */ + +#define select_prn() outb_p(SELECT_PRN, COMMAND_PORT); DE600_SLOW_DOWN +#define select_nic() outb_p(SELECT_NIC, COMMAND_PORT); DE600_SLOW_DOWN + +/* Thanks for hints from Mark Burton <markb@ordern.demon.co.uk> */ +#define de600_put_byte(data) ( \ + outb_p(((data) << 4) | WRITE_DATA , DATA_PORT), \ + outb_p(((data) & 0xf0) | WRITE_DATA | HI_NIBBLE, DATA_PORT)) + +/* + * The first two outb_p()'s below could perhaps be deleted if there + * would be more delay in the last two. Not certain about it yet... + */ +#define de600_put_command(cmd) ( \ + outb_p(( rx_page << 4) | COMMAND , DATA_PORT), \ + outb_p(( rx_page & 0xf0) | COMMAND | HI_NIBBLE, DATA_PORT), \ + outb_p(((rx_page | cmd) << 4) | COMMAND , DATA_PORT), \ + outb_p(((rx_page | cmd) & 0xf0) | COMMAND | HI_NIBBLE, DATA_PORT)) + +#define de600_setup_address(addr,type) ( \ + outb_p((((addr) << 4) & 0xf0) | type , DATA_PORT), \ + outb_p(( (addr) & 0xf0) | type | HI_NIBBLE, DATA_PORT), \ + outb_p((((addr) >> 4) & 0xf0) | type , DATA_PORT), \ + outb_p((((addr) >> 8) & 0xf0) | type | HI_NIBBLE, DATA_PORT)) + +#define rx_page_adr() ((rx_page & RX_PAGE2_SELECT)?(MEM_6K):(MEM_4K)) + +/* Flip bit, only 2 pages */ +#define next_rx_page() (rx_page ^= RX_PAGE2_SELECT) + +#define tx_page_adr(a) (((a) + 1) * MEM_2K) |