diff options
Diffstat (limited to 'drivers/net/e1000')
-rw-r--r-- | drivers/net/e1000/e1000_ethtool.c | 3 | ||||
-rw-r--r-- | drivers/net/e1000/e1000_hw.c | 685 | ||||
-rw-r--r-- | drivers/net/e1000/e1000_hw.h | 287 | ||||
-rw-r--r-- | drivers/net/e1000/e1000_main.c | 5 |
4 files changed, 964 insertions, 16 deletions
diff --git a/drivers/net/e1000/e1000_ethtool.c b/drivers/net/e1000/e1000_ethtool.c index 70238e089f1..0d6a16c5f8c 100644 --- a/drivers/net/e1000/e1000_ethtool.c +++ b/drivers/net/e1000/e1000_ethtool.c @@ -589,6 +589,7 @@ e1000_get_drvinfo(struct net_device *netdev, case e1000_82571: case e1000_82572: case e1000_82573: + case e1000_80003es2lan: sprintf(firmware_version, "%d.%d-%d", (eeprom_data & 0xF000) >> 12, (eeprom_data & 0x0FF0) >> 4, @@ -762,6 +763,7 @@ e1000_reg_test(struct e1000_adapter *adapter, uint64_t *data) /* there are several bits on newer hardware that are r/w */ case e1000_82571: case e1000_82572: + case e1000_80003es2lan: toggle = 0x7FFFF3FF; break; case e1000_82573: @@ -1320,6 +1322,7 @@ e1000_set_phy_loopback(struct e1000_adapter *adapter) case e1000_82571: case e1000_82572: case e1000_82573: + case e1000_80003es2lan: return e1000_integrated_phy_loopback(adapter); break; diff --git a/drivers/net/e1000/e1000_hw.c b/drivers/net/e1000/e1000_hw.c index 5ee42c75adb..63e237084a5 100644 --- a/drivers/net/e1000/e1000_hw.c +++ b/drivers/net/e1000/e1000_hw.c @@ -100,6 +100,8 @@ static void e1000_write_reg_io(struct e1000_hw *hw, uint32_t offset, #define E1000_WRITE_REG_IO(a, reg, val) \ e1000_write_reg_io((a), E1000_##reg, val) +static int32_t e1000_configure_kmrn_for_10_100(struct e1000_hw *hw); +static int32_t e1000_configure_kmrn_for_1000(struct e1000_hw *hw); /* IGP cable length table */ static const @@ -153,6 +155,11 @@ e1000_set_phy_type(struct e1000_hw *hw) hw->phy_type = e1000_phy_igp; break; } + case GG82563_E_PHY_ID: + if (hw->mac_type == e1000_80003es2lan) { + hw->phy_type = e1000_phy_gg82563; + break; + } /* Fall Through */ default: /* Should never have loaded on this device */ @@ -353,12 +360,19 @@ e1000_set_mac_type(struct e1000_hw *hw) case E1000_DEV_ID_82573L: hw->mac_type = e1000_82573; break; + case E1000_DEV_ID_80003ES2LAN_COPPER_DPT: + case E1000_DEV_ID_80003ES2LAN_SERDES_DPT: + hw->mac_type = e1000_80003es2lan; + break; default: /* Should never have loaded on this device */ return -E1000_ERR_MAC_TYPE; } switch(hw->mac_type) { + case e1000_80003es2lan: + hw->swfw_sync_present = TRUE; + /* fall through */ case e1000_82571: case e1000_82572: case e1000_82573: @@ -399,6 +413,7 @@ e1000_set_media_type(struct e1000_hw *hw) case E1000_DEV_ID_82546GB_SERDES: case E1000_DEV_ID_82571EB_SERDES: case E1000_DEV_ID_82572EI_SERDES: + case E1000_DEV_ID_80003ES2LAN_SERDES_DPT: hw->media_type = e1000_media_type_internal_serdes; break; default: @@ -575,6 +590,7 @@ e1000_reset_hw(struct e1000_hw *hw) /* fall through */ case e1000_82571: case e1000_82572: + case e1000_80003es2lan: ret_val = e1000_get_auto_rd_done(hw); if(ret_val) /* We don't want to continue accessing MAC registers. */ @@ -641,6 +657,7 @@ e1000_init_hw(struct e1000_hw *hw) uint16_t cmd_mmrbc; uint16_t stat_mmrbc; uint32_t mta_size; + uint32_t reg_data; uint32_t ctrl_ext; DEBUGFUNC("e1000_init_hw"); @@ -739,6 +756,7 @@ e1000_init_hw(struct e1000_hw *hw) case e1000_82571: case e1000_82572: case e1000_82573: + case e1000_80003es2lan: ctrl |= E1000_TXDCTL_COUNT_DESC; break; } @@ -752,12 +770,34 @@ e1000_init_hw(struct e1000_hw *hw) switch (hw->mac_type) { default: break; + case e1000_80003es2lan: + /* Enable retransmit on late collisions */ + reg_data = E1000_READ_REG(hw, TCTL); + reg_data |= E1000_TCTL_RTLC; + E1000_WRITE_REG(hw, TCTL, reg_data); + + /* Configure Gigabit Carry Extend Padding */ + reg_data = E1000_READ_REG(hw, TCTL_EXT); + reg_data &= ~E1000_TCTL_EXT_GCEX_MASK; + reg_data |= DEFAULT_80003ES2LAN_TCTL_EXT_GCEX; + E1000_WRITE_REG(hw, TCTL_EXT, reg_data); + + /* Configure Transmit Inter-Packet Gap */ + reg_data = E1000_READ_REG(hw, TIPG); + reg_data &= ~E1000_TIPG_IPGT_MASK; + reg_data |= DEFAULT_80003ES2LAN_TIPG_IPGT_1000; + E1000_WRITE_REG(hw, TIPG, reg_data); + + reg_data = E1000_READ_REG_ARRAY(hw, FFLT, 0x0001); + reg_data &= ~0x00100000; + E1000_WRITE_REG_ARRAY(hw, FFLT, 0x0001, reg_data); + /* Fall through */ case e1000_82571: case e1000_82572: ctrl = E1000_READ_REG(hw, TXDCTL1); - ctrl &= ~E1000_TXDCTL_WTHRESH; - ctrl |= E1000_TXDCTL_COUNT_DESC | E1000_TXDCTL_FULL_TX_DESC_WB; - ctrl |= (1 << 22); + ctrl = (ctrl & ~E1000_TXDCTL_WTHRESH) | E1000_TXDCTL_FULL_TX_DESC_WB; + if(hw->mac_type >= e1000_82571) + ctrl |= E1000_TXDCTL_COUNT_DESC; E1000_WRITE_REG(hw, TXDCTL1, ctrl); break; } @@ -1314,6 +1354,154 @@ e1000_copper_link_igp_setup(struct e1000_hw *hw) return E1000_SUCCESS; } +/******************************************************************** +* Copper link setup for e1000_phy_gg82563 series. +* +* hw - Struct containing variables accessed by shared code +*********************************************************************/ +static int32_t +e1000_copper_link_ggp_setup(struct e1000_hw *hw) +{ + int32_t ret_val; + uint16_t phy_data; + uint32_t reg_data; + + DEBUGFUNC("e1000_copper_link_ggp_setup"); + + if(!hw->phy_reset_disable) { + + /* Enable CRS on TX for half-duplex operation. */ + ret_val = e1000_read_phy_reg(hw, GG82563_PHY_MAC_SPEC_CTRL, + &phy_data); + if(ret_val) + return ret_val; + + phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX; + /* Use 25MHz for both link down and 1000BASE-T for Tx clock */ + phy_data |= GG82563_MSCR_TX_CLK_1000MBPS_25MHZ; + + ret_val = e1000_write_phy_reg(hw, GG82563_PHY_MAC_SPEC_CTRL, + phy_data); + if(ret_val) + return ret_val; + + /* Options: + * MDI/MDI-X = 0 (default) + * 0 - Auto for all speeds + * 1 - MDI mode + * 2 - MDI-X mode + * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes) + */ + ret_val = e1000_read_phy_reg(hw, GG82563_PHY_SPEC_CTRL, &phy_data); + if(ret_val) + return ret_val; + + phy_data &= ~GG82563_PSCR_CROSSOVER_MODE_MASK; + + switch (hw->mdix) { + case 1: + phy_data |= GG82563_PSCR_CROSSOVER_MODE_MDI; + break; + case 2: + phy_data |= GG82563_PSCR_CROSSOVER_MODE_MDIX; + break; + case 0: + default: + phy_data |= GG82563_PSCR_CROSSOVER_MODE_AUTO; + break; + } + + /* Options: + * disable_polarity_correction = 0 (default) + * Automatic Correction for Reversed Cable Polarity + * 0 - Disabled + * 1 - Enabled + */ + phy_data &= ~GG82563_PSCR_POLARITY_REVERSAL_DISABLE; + if(hw->disable_polarity_correction == 1) + phy_data |= GG82563_PSCR_POLARITY_REVERSAL_DISABLE; + ret_val = e1000_write_phy_reg(hw, GG82563_PHY_SPEC_CTRL, phy_data); + + if(ret_val) + return ret_val; + + /* SW Reset the PHY so all changes take effect */ + ret_val = e1000_phy_reset(hw); + if (ret_val) { + DEBUGOUT("Error Resetting the PHY\n"); + return ret_val; + } + } /* phy_reset_disable */ + + if (hw->mac_type == e1000_80003es2lan) { + /* Bypass RX and TX FIFO's */ + ret_val = e1000_write_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_FIFO_CTRL, + E1000_KUMCTRLSTA_FIFO_CTRL_RX_BYPASS | + E1000_KUMCTRLSTA_FIFO_CTRL_TX_BYPASS); + if (ret_val) + return ret_val; + + ret_val = e1000_read_phy_reg(hw, GG82563_PHY_SPEC_CTRL_2, &phy_data); + if (ret_val) + return ret_val; + + phy_data &= ~GG82563_PSCR2_REVERSE_AUTO_NEG; + ret_val = e1000_write_phy_reg(hw, GG82563_PHY_SPEC_CTRL_2, phy_data); + + if (ret_val) + return ret_val; + + reg_data = E1000_READ_REG(hw, CTRL_EXT); + reg_data &= ~(E1000_CTRL_EXT_LINK_MODE_MASK); + E1000_WRITE_REG(hw, CTRL_EXT, reg_data); + + ret_val = e1000_read_phy_reg(hw, GG82563_PHY_PWR_MGMT_CTRL, + &phy_data); + if (ret_val) + return ret_val; + + /* Do not init these registers when the HW is in IAMT mode, since the + * firmware will have already initialized them. We only initialize + * them if the HW is not in IAMT mode. + */ + if (e1000_check_mng_mode(hw) == FALSE) { + /* Enable Electrical Idle on the PHY */ + phy_data |= GG82563_PMCR_ENABLE_ELECTRICAL_IDLE; + ret_val = e1000_write_phy_reg(hw, GG82563_PHY_PWR_MGMT_CTRL, + phy_data); + if (ret_val) + return ret_val; + + ret_val = e1000_read_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, + &phy_data); + if (ret_val) + return ret_val; + + /* Enable Pass False Carrier on the PHY */ + phy_data |= GG82563_KMCR_PASS_FALSE_CARRIER; + + ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, + phy_data); + if (ret_val) + return ret_val; + } + + /* Workaround: Disable padding in Kumeran interface in the MAC + * and in the PHY to avoid CRC errors. + */ + ret_val = e1000_read_phy_reg(hw, GG82563_PHY_INBAND_CTRL, + &phy_data); + if (ret_val) + return ret_val; + phy_data |= GG82563_ICR_DIS_PADDING; + ret_val = e1000_write_phy_reg(hw, GG82563_PHY_INBAND_CTRL, + phy_data); + if (ret_val) + return ret_val; + } + + return E1000_SUCCESS; +} /******************************************************************** * Copper link setup for e1000_phy_m88 series. @@ -1524,6 +1712,7 @@ e1000_setup_copper_link(struct e1000_hw *hw) int32_t ret_val; uint16_t i; uint16_t phy_data; + uint16_t reg_data; DEBUGFUNC("e1000_setup_copper_link"); @@ -1532,6 +1721,22 @@ e1000_setup_copper_link(struct e1000_hw *hw) if(ret_val) return ret_val; + switch (hw->mac_type) { + case e1000_80003es2lan: + ret_val = e1000_read_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_INB_CTRL, + ®_data); + if (ret_val) + return ret_val; + reg_data |= E1000_KUMCTRLSTA_INB_CTRL_DIS_PADDING; + ret_val = e1000_write_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_INB_CTRL, + reg_data); + if (ret_val) + return ret_val; + break; + default: + break; + } + if (hw->phy_type == e1000_phy_igp || hw->phy_type == e1000_phy_igp_2) { ret_val = e1000_copper_link_igp_setup(hw); @@ -1541,6 +1746,10 @@ e1000_setup_copper_link(struct e1000_hw *hw) ret_val = e1000_copper_link_mgp_setup(hw); if(ret_val) return ret_val; + } else if (hw->phy_type == e1000_phy_gg82563) { + ret_val = e1000_copper_link_ggp_setup(hw); + if(ret_val) + return ret_val; } if(hw->autoneg) { @@ -1588,6 +1797,59 @@ e1000_setup_copper_link(struct e1000_hw *hw) } /****************************************************************************** +* Configure the MAC-to-PHY interface for 10/100Mbps +* +* hw - Struct containing variables accessed by shared code +******************************************************************************/ +static int32_t +e1000_configure_kmrn_for_10_100(struct e1000_hw *hw) +{ + int32_t ret_val = E1000_SUCCESS; + uint32_t tipg; + uint16_t reg_data; + + DEBUGFUNC("e1000_configure_kmrn_for_10_100"); + + reg_data = E1000_KUMCTRLSTA_HD_CTRL_10_100_DEFAULT; + ret_val = e1000_write_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_HD_CTRL, + reg_data); + if (ret_val) + return ret_val; + + /* Configure Transmit Inter-Packet Gap */ + tipg = E1000_READ_REG(hw, TIPG); + tipg &= ~E1000_TIPG_IPGT_MASK; + tipg |= DEFAULT_80003ES2LAN_TIPG_IPGT_10_100; + E1000_WRITE_REG(hw, TIPG, tipg); + + return ret_val; +} + +static int32_t +e1000_configure_kmrn_for_1000(struct e1000_hw *hw) +{ + int32_t ret_val = E1000_SUCCESS; + uint16_t reg_data; + uint32_t tipg; + + DEBUGFUNC("e1000_configure_kmrn_for_1000"); + + reg_data = E1000_KUMCTRLSTA_HD_CTRL_1000_DEFAULT; + ret_val = e1000_write_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_HD_CTRL, + reg_data); + if (ret_val) + return ret_val; + + /* Configure Transmit Inter-Packet Gap */ + tipg = E1000_READ_REG(hw, TIPG); + tipg &= ~E1000_TIPG_IPGT_MASK; + tipg |= DEFAULT_80003ES2LAN_TIPG_IPGT_1000; + E1000_WRITE_REG(hw, TIPG, tipg); + + return ret_val; +} + +/****************************************************************************** * Configures PHY autoneg and flow control advertisement settings * * hw - Struct containing variables accessed by shared code @@ -1808,7 +2070,8 @@ e1000_phy_force_speed_duplex(struct e1000_hw *hw) /* Write the configured values back to the Device Control Reg. */ E1000_WRITE_REG(hw, CTRL, ctrl); - if (hw->phy_type == e1000_phy_m88) { + if ((hw->phy_type == e1000_phy_m88) || + (hw->phy_type == e1000_phy_gg82563)) { ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); if(ret_val) return ret_val; @@ -1877,7 +2140,8 @@ e1000_phy_force_speed_duplex(struct e1000_hw *hw) msec_delay(100); } if((i == 0) && - (hw->phy_type == e1000_phy_m88)) { + ((hw->phy_type == e1000_phy_m88) || + (hw->phy_type == e1000_phy_gg82563))) { /* We didn't get link. Reset the DSP and wait again for link. */ ret_val = e1000_phy_reset_dsp(hw); if(ret_val) { @@ -1936,6 +2200,27 @@ e1000_phy_force_speed_duplex(struct e1000_hw *hw) if(ret_val) return ret_val; } + } else if (hw->phy_type == e1000_phy_gg82563) { + /* The TX_CLK of the Extended PHY Specific Control Register defaults + * to 2.5MHz on a reset. We need to re-force it back to 25MHz, if + * we're not in a forced 10/duplex configuration. */ + ret_val = e1000_read_phy_reg(hw, GG82563_PHY_MAC_SPEC_CTRL, &phy_data); + if (ret_val) + return ret_val; + + phy_data &= ~GG82563_MSCR_TX_CLK_MASK; + if ((hw->forced_speed_duplex == e1000_10_full) || + (hw->forced_speed_duplex == e1000_10_half)) + phy_data |= GG82563_MSCR_TX_CLK_10MBPS_2_5MHZ; + else + phy_data |= GG82563_MSCR_TX_CLK_100MBPS_25MHZ; + + /* Also due to the reset, we need to enable CRS on Tx. */ + phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX; + + ret_val = e1000_write_phy_reg(hw, GG82563_PHY_MAC_SPEC_CTRL, phy_data); + if (ret_val) + return ret_val; } return E1000_SUCCESS; } @@ -2598,6 +2883,16 @@ e1000_get_speed_and_duplex(struct e1000_hw *hw, } } + if ((hw->mac_type == e1000_80003es2lan) && + (hw->media_type == e1000_media_type_copper)) { + if (*speed == SPEED_1000) + ret_val = e1000_configure_kmrn_for_1000(hw); + else + ret_val = e1000_configure_kmrn_for_10_100(hw); + if (ret_val) + return ret_val; + } + return E1000_SUCCESS; } @@ -2773,6 +3068,72 @@ e1000_shift_in_mdi_bits(struct e1000_hw *hw) return data; } +int32_t +e1000_swfw_sync_acquire(struct e1000_hw *hw, uint16_t mask) +{ + uint32_t swfw_sync = 0; + uint32_t swmask = mask; + uint32_t fwmask = mask << 16; + int32_t timeout = 200; + + DEBUGFUNC("e1000_swfw_sync_acquire"); + + if (!hw->swfw_sync_present) + return e1000_get_hw_eeprom_semaphore(hw); + + while(timeout) { + if (e1000_get_hw_eeprom_semaphore(hw)) + return -E1000_ERR_SWFW_SYNC; + + swfw_sync = E1000_READ_REG(hw, SW_FW_SYNC); + if (!(swfw_sync & (fwmask | swmask))) { + break; + } + + /* firmware currently using resource (fwmask) */ + /* or other software thread currently using resource (swmask) */ + e1000_put_hw_eeprom_semaphore(hw); + msec_delay_irq(5); + timeout--; + } + + if (!timeout) { + DEBUGOUT("Driver can't access resource, SW_FW_SYNC timeout.\n"); + return -E1000_ERR_SWFW_SYNC; + } + + swfw_sync |= swmask; + E1000_WRITE_REG(hw, SW_FW_SYNC, swfw_sync); + + e1000_put_hw_eeprom_semaphore(hw); + return E1000_SUCCESS; +} + +void +e1000_swfw_sync_release(struct e1000_hw *hw, uint16_t mask) +{ + uint32_t swfw_sync; + uint32_t swmask = mask; + + DEBUGFUNC("e1000_swfw_sync_release"); + + if (!hw->swfw_sync_present) { + e1000_put_hw_eeprom_semaphore(hw); + return; + } + + /* if (e1000_get_hw_eeprom_semaphore(hw)) + * return -E1000_ERR_SWFW_SYNC; */ + while (e1000_get_hw_eeprom_semaphore(hw) != E1000_SUCCESS); + /* empty */ + + swfw_sync = E1000_READ_REG(hw, SW_FW_SYNC); + swfw_sync &= ~swmask; + E1000_WRITE_REG(hw, SW_FW_SYNC, swfw_sync); + + e1000_put_hw_eeprom_semaphore(hw); +} + /***************************************************************************** * Reads the value from a PHY register, if the value is on a specific non zero * page, sets the page first. @@ -2785,22 +3146,55 @@ e1000_read_phy_reg(struct e1000_hw *hw, uint16_t *phy_data) { uint32_t ret_val; + uint16_t swfw; DEBUGFUNC("e1000_read_phy_reg"); + if ((hw->mac_type == e1000_80003es2lan) && + (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)) { + swfw = E1000_SWFW_PHY1_SM; + } else { + swfw = E1000_SWFW_PHY0_SM; + } + if (e1000_swfw_sync_acquire(hw, swfw)) + return -E1000_ERR_SWFW_SYNC; + if((hw->phy_type == e1000_phy_igp || hw->phy_type == e1000_phy_igp_2) && (reg_addr > MAX_PHY_MULTI_PAGE_REG)) { ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT, (uint16_t)reg_addr); if(ret_val) { + e1000_swfw_sync_release(hw, swfw); return ret_val; } + } else if (hw->phy_type == e1000_phy_gg82563) { + if (((reg_addr & MAX_PHY_REG_ADDRESS) > MAX_PHY_MULTI_PAGE_REG) || + (hw->mac_type == e1000_80003es2lan)) { + /* Select Configuration Page */ + if ((reg_addr & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) { + ret_val = e1000_write_phy_reg_ex(hw, GG82563_PHY_PAGE_SELECT, + (uint16_t)((uint16_t)reg_addr >> GG82563_PAGE_SHIFT)); + } else { + /* Use Alternative Page Select register to access + * registers 30 and 31 + */ + ret_val = e1000_write_phy_reg_ex(hw, + GG82563_PHY_PAGE_SELECT_ALT, + (uint16_t)((uint16_t)reg_addr >> GG82563_PAGE_SHIFT)); + } + + if (ret_val) { + e1000_swfw_sync_release(hw, swfw); + return ret_val; + } + } } ret_val = e1000_read_phy_reg_ex(hw, MAX_PHY_REG_ADDRESS & reg_addr, phy_data); + e1000_swfw_sync_release(hw, swfw); return ret_val; } @@ -2891,22 +3285,55 @@ e1000_write_phy_reg(struct e1000_hw *hw, uint16_t phy_data) { uint32_t ret_val; + uint16_t swfw; DEBUGFUNC("e1000_write_phy_reg"); + if ((hw->mac_type == e1000_80003es2lan) && + (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)) { + swfw = E1000_SWFW_PHY1_SM; + } else { + swfw = E1000_SWFW_PHY0_SM; + } + if (e1000_swfw_sync_acquire(hw, swfw)) + return -E1000_ERR_SWFW_SYNC; + if((hw->phy_type == e1000_phy_igp || hw->phy_type == e1000_phy_igp_2) && (reg_addr > MAX_PHY_MULTI_PAGE_REG)) { ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT, (uint16_t)reg_addr); if(ret_val) { + e1000_swfw_sync_release(hw, swfw); return ret_val; } + } else if (hw->phy_type == e1000_phy_gg82563) { + if (((reg_addr & MAX_PHY_REG_ADDRESS) > MAX_PHY_MULTI_PAGE_REG) || + (hw->mac_type == e1000_80003es2lan)) { + /* Select Configuration Page */ + if ((reg_addr & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) { + ret_val = e1000_write_phy_reg_ex(hw, GG82563_PHY_PAGE_SELECT, + (uint16_t)((uint16_t)reg_addr >> GG82563_PAGE_SHIFT)); + } else { + /* Use Alternative Page Select register to access + * registers 30 and 31 + */ + ret_val = e1000_write_phy_reg_ex(hw, + GG82563_PHY_PAGE_SELECT_ALT, + (uint16_t)((uint16_t)reg_addr >> GG82563_PAGE_SHIFT)); + } + + if (ret_val) { + e1000_swfw_sync_release(hw, swfw); + return ret_val; + } + } } ret_val = e1000_write_phy_reg_ex(hw, MAX_PHY_REG_ADDRESS & reg_addr, phy_data); + e1000_swfw_sync_release(hw, swfw); return ret_val; } @@ -2973,6 +3400,65 @@ e1000_write_phy_reg_ex(struct e1000_hw *hw, return E1000_SUCCESS; } +int32_t +e1000_read_kmrn_reg(struct e1000_hw *hw, + uint32_t reg_addr, + uint16_t *data) +{ + uint32_t reg_val; + uint16_t swfw; + DEBUGFUNC("e1000_read_kmrn_reg"); + + if ((hw->mac_type == e1000_80003es2lan) && + (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)) { + swfw = E1000_SWFW_PHY1_SM; + } else { + swfw = E1000_SWFW_PHY0_SM; + } + if (e1000_swfw_sync_acquire(hw, swfw)) + return -E1000_ERR_SWFW_SYNC; + + /* Write register address */ + reg_val = ((reg_addr << E1000_KUMCTRLSTA_OFFSET_SHIFT) & + E1000_KUMCTRLSTA_OFFSET) | + E1000_KUMCTRLSTA_REN; + E1000_WRITE_REG(hw, KUMCTRLSTA, reg_val); + udelay(2); + + /* Read the data returned */ + reg_val = E1000_READ_REG(hw, KUMCTRLSTA); + *data = (uint16_t)reg_val; + + e1000_swfw_sync_release(hw, swfw); + return E1000_SUCCESS; +} + +int32_t +e1000_write_kmrn_reg(struct e1000_hw *hw, + uint32_t reg_addr, + uint16_t data) +{ + uint32_t reg_val; + uint16_t swfw; + DEBUGFUNC("e1000_write_kmrn_reg"); + + if ((hw->mac_type == e1000_80003es2lan) && + (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)) { + swfw = E1000_SWFW_PHY1_SM; + } else { + swfw = E1000_SWFW_PHY0_SM; + } + if (e1000_swfw_sync_acquire(hw, swfw)) + return -E1000_ERR_SWFW_SYNC; + + reg_val = ((reg_addr << E1000_KUMCTRLSTA_OFFSET_SHIFT) & + E1000_KUMCTRLSTA_OFFSET) | data; + E1000_WRITE_REG(hw, KUMCTRLSTA, reg_val); + udelay(2); + + e1000_swfw_sync_release(hw, swfw); + return E1000_SUCCESS; +} /****************************************************************************** * Returns the PHY to the power-on reset state @@ -2985,6 +3471,7 @@ e1000_phy_hw_reset(struct e1000_hw *hw) uint32_t ctrl, ctrl_ext; uint32_t led_ctrl; int32_t ret_val; + uint16_t swfw; DEBUGFUNC("e1000_phy_hw_reset"); @@ -2997,6 +3484,16 @@ e1000_phy_hw_reset(struct e1000_hw *hw) DEBUGOUT("Resetting Phy...\n"); if(hw->mac_type > e1000_82543) { + if ((hw->mac_type == e1000_80003es2lan) && + (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)) { + swfw = E1000_SWFW_PHY1_SM; + } else { + swfw = E1000_SWFW_PHY0_SM; + } + if (e1000_swfw_sync_acquire(hw, swfw)) { + e1000_release_software_semaphore(hw); + return -E1000_ERR_SWFW_SYNC; + } /* Read the device control register and assert the E1000_CTRL_PHY_RST * bit. Then, take it out of reset. * For pre-e1000_82571 hardware, we delay for 10ms between the assert @@ -3017,6 +3514,7 @@ e1000_phy_hw_reset(struct e1000_hw *hw) if (hw->mac_type >= e1000_82571) msec_delay(10); + e1000_swfw_sync_release(hw, swfw); } else { /* Read the Extended Device Control Register, assert the PHY_RESET_DIR * bit to put the PHY into reset. Then, take it out of reset. @@ -3043,6 +3541,7 @@ e1000_phy_hw_reset(struct e1000_hw *hw) /* Wait for FW to finish PHY configuration. */ ret_val = e1000_get_phy_cfg_done(hw); + e1000_release_software_semaphore(hw); return ret_val; } @@ -3120,6 +3619,15 @@ e1000_detect_gig_phy(struct e1000_hw *hw) return E1000_SUCCESS; } + /* ESB-2 PHY reads require e1000_phy_gg82563 to be set because of a work- + * around that forces PHY page 0 to be set or the reads fail. The rest of + * the code in this routine uses e1000_read_phy_reg to read the PHY ID. + * So for ESB-2 we need to have this set so our reads won't fail. If the + * attached PHY is not a e1000_phy_gg82563, the routines below will figure + * this out as well. */ + if (hw->mac_type == e1000_80003es2lan) + hw->phy_type = e1000_phy_gg82563; + /* Read the PHY ID Registers to identify which PHY is onboard. */ ret_val = e1000_read_phy_reg(hw, PHY_ID1, &phy_id_high); if(ret_val) @@ -3157,6 +3665,9 @@ e1000_detect_gig_phy(struct e1000_hw *hw) case e1000_82573: if(hw->phy_id == M88E1111_I_PHY_ID) match = TRUE; break; + case e1000_80003es2lan: + if (hw->phy_id == GG82563_E_PHY_ID) match = TRUE; + break; default: DEBUGOUT1("Invalid MAC type %d\n", hw->mac_type); return -E1000_ERR_CONFIG; @@ -3183,8 +3694,10 @@ e1000_phy_reset_dsp(struct e1000_hw *hw) DEBUGFUNC("e1000_phy_reset_dsp"); do { - ret_val = e1000_write_phy_reg(hw, 29, 0x001d); - if(ret_val) break; + if (hw->phy_type != e1000_phy_gg82563) { + ret_val = e1000_write_phy_reg(hw, 29, 0x001d); + if(ret_val) break; + } ret_val = e1000_write_phy_reg(hw, 30, 0x00c1); if(ret_val) break; ret_val = e1000_write_phy_reg(hw, 30, 0x0000); @@ -3316,8 +3829,17 @@ e1000_phy_m88_get_info(struct e1000_hw *hw, /* Cable Length Estimation and Local/Remote Receiver Information * are only valid at 1000 Mbps. */ - phy_info->cable_length = ((phy_data & M88E1000_PSSR_CABLE_LENGTH) >> - M88E1000_PSSR_CABLE_LENGTH_SHIFT); + if (hw->phy_type != e1000_phy_gg82563) { + phy_info->cable_length = ((phy_data & M88E1000_PSSR_CABLE_LENGTH) >> + M88E1000_PSSR_CABLE_LENGTH_SHIFT); + } else { + ret_val = e1000_read_phy_reg(hw, GG82563_PHY_DSP_DISTANCE, + &phy_data); + if (ret_val) + return ret_val; + + phy_info->cable_length = phy_data & GG82563_DSPD_CABLE_LENGTH; + } ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_data); if(ret_val) @@ -3511,6 +4033,20 @@ e1000_init_eeprom_params(struct e1000_hw *hw) E1000_WRITE_REG(hw, EECD, eecd); } break; + case e1000_80003es2lan: + eeprom->type = e1000_eeprom_spi; + eeprom->opcode_bits = 8; + eeprom->delay_usec = 1; + if (eecd & E1000_EECD_ADDR_BITS) { + eeprom->page_size = 32; + eeprom->address_bits = 16; + } else { + eeprom->page_size = 8; + eeprom->address_bits = 8; + } + eeprom->use_eerd = TRUE; + eeprom->use_eewr = FALSE; + break; default: break; } @@ -3691,9 +4227,8 @@ e1000_acquire_eeprom(struct e1000_hw *hw) DEBUGFUNC("e1000_acquire_eeprom"); - if(e1000_get_hw_eeprom_semaphore(hw)) - return -E1000_ERR_EEPROM; - + if (e1000_swfw_sync_acquire(hw, E1000_SWFW_EEP_SM)) + return -E1000_ERR_SWFW_SYNC; eecd = E1000_READ_REG(hw, EECD); if (hw->mac_type != e1000_82573) { @@ -3712,7 +4247,7 @@ e1000_acquire_eeprom(struct e1000_hw *hw) eecd &= ~E1000_EECD_REQ; E1000_WRITE_REG(hw, EECD, eecd); DEBUGOUT("Could not acquire EEPROM grant\n"); - e1000_put_hw_eeprom_semaphore(hw); + e1000_swfw_sync_release(hw, E1000_SWFW_EEP_SM); return -E1000_ERR_EEPROM; } } @@ -3835,7 +4370,7 @@ e1000_release_eeprom(struct e1000_hw *hw) E1000_WRITE_REG(hw, EECD, eecd); } - e1000_put_hw_eeprom_semaphore(hw); + e1000_swfw_sync_release(hw, E1000_SWFW_EEP_SM); } /****************************************************************************** @@ -3914,6 +4449,8 @@ e1000_read_eeprom(struct e1000_hw *hw, if (e1000_is_onboard_nvm_eeprom(hw) == TRUE && hw->eeprom.use_eerd == FALSE) { switch (hw->mac_type) { + case e1000_80003es2lan: + break; default: /* Prepare the EEPROM for reading */ if (e1000_acquire_eeprom(hw) != E1000_SUCCESS) @@ -4031,6 +4568,9 @@ e1000_write_eeprom_eewr(struct e1000_hw *hw, uint32_t i = 0; int32_t error = 0; + if (e1000_swfw_sync_acquire(hw, E1000_SWFW_EEP_SM)) + return -E1000_ERR_SWFW_SYNC; + for (i = 0; i < words; i++) { register_value = (data[i] << E1000_EEPROM_RW_REG_DATA) | ((offset+i) << E1000_EEPROM_RW_ADDR_SHIFT) | @@ -4050,6 +4590,7 @@ e1000_write_eeprom_eewr(struct e1000_hw *hw, } } + e1000_swfw_sync_release(hw, E1000_SWFW_EEP_SM); return error; } @@ -4091,6 +4632,8 @@ e1000_is_onboard_nvm_eeprom(struct e1000_hw *hw) { uint32_t eecd = 0; + DEBUGFUNC("e1000_is_onboard_nvm_eeprom"); + if(hw->mac_type == e1000_82573) { eecd = E1000_READ_REG(hw, EECD); @@ -4517,6 +5060,7 @@ e1000_read_mac_addr(struct e1000_hw * hw) case e1000_82546: case e1000_82546_rev_3: case e1000_82571: + case e1000_80003es2lan: if(E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1) hw->perm_mac_addr[5] ^= 0x01; break; @@ -4778,6 +5322,7 @@ e1000_rar_set(struct e1000_hw *hw, switch (hw->mac_type) { case e1000_82571: case e1000_82572: + case e1000_80003es2lan: if (hw->leave_av_bit_off == TRUE) break; default: @@ -5364,6 +5909,7 @@ e1000_get_bus_info(struct e1000_hw *hw) hw->bus_width = e1000_bus_width_pciex_1; break; case e1000_82571: + case e1000_80003es2lan: hw->bus_type = e1000_bus_type_pci_express; hw->bus_speed = e1000_bus_speed_2500; hw->bus_width = e1000_bus_width_pciex_4; @@ -5509,6 +6055,34 @@ e1000_get_cable_length(struct e1000_hw *hw, return -E1000_ERR_PHY; break; } + } else if (hw->phy_type == e1000_phy_gg82563) { + ret_val = e1000_read_phy_reg(hw, GG82563_PHY_DSP_DISTANCE, + &phy_data); + if (ret_val) + return ret_val; + cable_length = phy_data & GG82563_DSPD_CABLE_LENGTH; + + switch (cable_length) { + case e1000_gg_cable_length_60: + *min_length = 0; + *max_length = e1000_igp_cable_length_60; + break; + case e1000_gg_cable_length_60_115: + *min_length = e1000_igp_cable_length_60; + *max_length = e1000_igp_cable_length_115; + break; + case e1000_gg_cable_length_115_150: + *min_length = e1000_igp_cable_length_115; + *max_length = e1000_igp_cable_length_150; + break; + case e1000_gg_cable_length_150: + *min_length = e1000_igp_cable_length_150; + *max_length = e1000_igp_cable_length_180; + break; + default: + return -E1000_ERR_PHY; + break; + } } else if(hw->phy_type == e1000_phy_igp) { /* For IGP PHY */ uint16_t agc_reg_array[IGP01E1000_PHY_CHANNEL_NUM] = {IGP01E1000_PHY_AGC_A, @@ -5618,7 +6192,8 @@ e1000_check_polarity(struct e1000_hw *hw, DEBUGFUNC("e1000_check_polarity"); - if(hw->phy_type == e1000_phy_m88) { + if ((hw->phy_type == e1000_phy_m88) || + (hw->phy_type == e1000_phy_gg82563)) { /* return the Polarity bit in the Status register. */ ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data); @@ -5687,7 +6262,8 @@ e1000_check_downshift(struct e1000_hw *hw) return ret_val; hw->speed_downgraded = (phy_data & IGP01E1000_PLHR_SS_DOWNGRADE) ? 1 : 0; - } else if(hw->phy_type == e1000_phy_m88) { + } else if ((hw->phy_type == e1000_phy_m88) || + (hw->phy_type == e1000_phy_gg82563)) { ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data); if(ret_val) @@ -6720,6 +7296,7 @@ e1000_get_auto_rd_done(struct e1000_hw *hw) case e1000_82571: case e1000_82572: case e1000_82573: + case e1000_80003es2lan: while(timeout) { if (E1000_READ_REG(hw, EECD) & E1000_EECD_AUTO_RD) break; else msec_delay(1); @@ -6763,6 +7340,11 @@ e1000_get_phy_cfg_done(struct e1000_hw *hw) default: msec_delay(10); break; + case e1000_80003es2lan: + /* Separate *_CFG_DONE_* bit for each port */ + if (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1) + cfg_mask = E1000_EEPROM_CFG_DONE_PORT_1; + /* Fall Through */ case e1000_82571: case e1000_82572: while (timeout) { @@ -6805,6 +7387,11 @@ e1000_get_hw_eeprom_semaphore(struct e1000_hw *hw) if(!hw->eeprom_semaphore_present) return E1000_SUCCESS; + if (hw->mac_type == e1000_80003es2lan) { + /* Get the SW semaphore. */ + if (e1000_get_software_semaphore(hw) != E1000_SUCCESS) + return -E1000_ERR_EEPROM; + } /* Get the FW semaphore. */ timeout = hw->eeprom.word_size + 1; @@ -6850,10 +7437,75 @@ e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw) return; swsm = E1000_READ_REG(hw, SWSM); + if (hw->mac_type == e1000_80003es2lan) { + /* Release both semaphores. */ + swsm &= ~(E1000_SWSM_SMBI | E1000_SWSM_SWESMBI); + } else swsm &= ~(E1000_SWSM_SWESMBI); E1000_WRITE_REG(hw, SWSM, swsm); } +/*************************************************************************** + * + * Obtaining software semaphore bit (SMBI) before resetting PHY. + * + * hw: Struct containing variables accessed by shared code + * + * returns: - E1000_ERR_RESET if fail to obtain semaphore. + * E1000_SUCCESS at any other case. + * + ***************************************************************************/ +int32_t +e1000_get_software_semaphore(struct e1000_hw *hw) +{ + int32_t timeout = hw->eeprom.word_size + 1; + uint32_t swsm; + + DEBUGFUNC("e1000_get_software_semaphore"); + + if (hw->mac_type != e1000_80003es2lan) + return E1000_SUCCESS; + + while(timeout) { + swsm = E1000_READ_REG(hw, SWSM); + /* If SMBI bit cleared, it is now set and we hold the semaphore */ + if(!(swsm & E1000_SWSM_SMBI)) + break; + msec_delay_irq(1); + timeout--; + } + + if(!timeout) { + DEBUGOUT("Driver can't access device - SMBI bit is set.\n"); + return -E1000_ERR_RESET; + } + + return E1000_SUCCESS; +} + +/*************************************************************************** + * + * Release semaphore bit (SMBI). + * + * hw: Struct containing variables accessed by shared code + * + ***************************************************************************/ +void +e1000_release_software_semaphore(struct e1000_hw *hw) +{ + uint32_t swsm; + + DEBUGFUNC("e1000_release_software_semaphore"); + + if (hw->mac_type != e1000_80003es2lan) + return; + + swsm = E1000_READ_REG(hw, SWSM); + /* Release the SW semaphores.*/ + swsm &= ~E1000_SWSM_SMBI; + E1000_WRITE_REG(hw, SWSM, swsm); +} + /****************************************************************************** * Checks if PHY reset is blocked due to SOL/IDER session, for example. * Returning E1000_BLK_PHY_RESET isn't necessarily an error. But it's up to @@ -6890,6 +7542,7 @@ e1000_arc_subsystem_valid(struct e1000_hw *hw) case e1000_82571: case e1000_82572: case e1000_82573: + case e1000_80003es2lan: fwsm = E1000_READ_REG(hw, FWSM); if((fwsm & E1000_FWSM_MODE_MASK) != 0) return TRUE; diff --git a/drivers/net/e1000/e1000_hw.h b/drivers/net/e1000/e1000_hw.h index f565b201c49..947a156bd70 100644 --- a/drivers/net/e1000/e1000_hw.h +++ b/drivers/net/e1000/e1000_hw.h @@ -60,6 +60,7 @@ typedef enum { e1000_82571, e1000_82572, e1000_82573, + e1000_80003es2lan, e1000_num_macs } e1000_mac_type; @@ -139,6 +140,13 @@ typedef enum { } e1000_cable_length; typedef enum { + e1000_gg_cable_length_60 = 0, + e1000_gg_cable_length_60_115 = 1, + e1000_gg_cable_length_115_150 = 2, + e1000_gg_cable_length_150 = 4 +} e1000_gg_cable_length; + +typedef enum { e1000_igp_cable_length_10 = 10, e1000_igp_cable_length_20 = 20, e1000_igp_cable_length_30 = 30, @@ -208,6 +216,7 @@ typedef enum { e1000_phy_m88 = 0, e1000_phy_igp, e1000_phy_igp_2, + e1000_phy_gg82563, e1000_phy_undefined = 0xFF } e1000_phy_type; @@ -281,6 +290,7 @@ typedef enum { #define E1000_ERR_MASTER_REQUESTS_PENDING 10 #define E1000_ERR_HOST_INTERFACE_COMMAND 11 #define E1000_BLK_PHY_RESET 12 +#define E1000_ERR_SWFW_SYNC 13 /* Function prototypes */ /* Initialization */ @@ -304,6 +314,8 @@ int32_t e1000_phy_hw_reset(struct e1000_hw *hw); int32_t e1000_phy_reset(struct e1000_hw *hw); int32_t e1000_phy_get_info(struct e1000_hw *hw, struct e1000_phy_info *phy_info); int32_t e1000_validate_mdi_setting(struct e1000_hw *hw); +int32_t e1000_read_kmrn_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t *data); +int32_t e1000_write_kmrn_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t data); /* EEPROM Functions */ int32_t e1000_init_eeprom_params(struct e1000_hw *hw); @@ -454,6 +466,8 @@ int32_t e1000_check_phy_reset_block(struct e1000_hw *hw); #define E1000_DEV_ID_82573E_IAMT 0x108C #define E1000_DEV_ID_82573L 0x109A #define E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3 0x10B5 +#define E1000_DEV_ID_80003ES2LAN_COPPER_DPT 0x1096 +#define E1000_DEV_ID_80003ES2LAN_SERDES_DPT 0x1098 #define NODE_ADDRESS_SIZE 6 @@ -850,6 +864,7 @@ struct e1000_ffvt_entry { #define E1000_TXCW 0x00178 /* TX Configuration Word - RW */ #define E1000_RXCW 0x00180 /* RX Configuration Word - RO */ #define E1000_TCTL 0x00400 /* TX Control - RW */ +#define E1000_TCTL_EXT 0x00404 /* Extended TX Control - RW */ #define E1000_TIPG 0x00410 /* TX Inter-packet gap -RW */ #define E1000_TBT 0x00448 /* TX Burst Timer - RW */ #define E1000_AIT 0x00458 /* Adaptive Interframe Spacing Throttle - RW */ @@ -996,6 +1011,11 @@ struct e1000_ffvt_entry { #define E1000_FFMT 0x09000 /* Flexible Filter Mask Table - RW Array */ #define E1000_FFVT 0x09800 /* Flexible Filter Value Table - RW Array */ +#define E1000_KUMCTRLSTA 0x00034 /* MAC-PHY interface - RW */ +#define E1000_MDPHYA 0x0003C /* PHY address - RW */ +#define E1000_MANC2H 0x05860 /* Managment Control To Host - RW */ +#define E1000_SW_FW_SYNC 0x05B5C /* Software-Firmware Synchronization - RW */ + #define E1000_GCR 0x05B00 /* PCI-Ex Control */ #define E1000_GSCL_1 0x05B10 /* PCI-Ex Statistic Control #1 */ #define E1000_GSCL_2 0x05B14 /* PCI-Ex Statistic Control #2 */ @@ -1065,6 +1085,7 @@ struct e1000_ffvt_entry { #define E1000_82542_RXCW E1000_RXCW #define E1000_82542_MTA 0x00200 #define E1000_82542_TCTL E1000_TCTL +#define E1000_82542_TCTL_EXT E1000_TCTL_EXT #define E1000_82542_TIPG E1000_TIPG #define E1000_82542_TDBAL 0x00420 #define E1000_82542_TDBAH 0x00424 @@ -1212,6 +1233,8 @@ struct e1000_ffvt_entry { #define E1000_82542_RSSRK E1000_RSSRK #define E1000_82542_RSSIM E1000_RSSIM #define E1000_82542_RSSIR E1000_RSSIR +#define E1000_82542_KUMCTRLSTA E1000_KUMCTRLSTA +#define E1000_82542_SW_FW_SYNC E1000_SW_FW_SYNC /* Statistics counters collected by the MAC */ struct e1000_hw_stats { @@ -1303,6 +1326,7 @@ struct e1000_hw { e1000_ffe_config ffe_config_state; uint32_t asf_firmware_present; uint32_t eeprom_semaphore_present; + uint32_t swfw_sync_present; unsigned long io_base; uint32_t phy_id; uint32_t phy_revision; @@ -1394,6 +1418,8 @@ struct e1000_hw { #define E1000_CTRL_FRCDPX 0x00001000 /* Force Duplex */ #define E1000_CTRL_D_UD_EN 0x00002000 /* Dock/Undock enable */ #define E1000_CTRL_D_UD_POLARITY 0x00004000 /* Defined polarity of Dock/Undock indication in SDP[0] */ +#define E1000_CTRL_FORCE_PHY_RESET 0x00008000 /* Reset both PHY ports, through PHYRST_N pin */ +#define E1000_CTRL_EXT_LINK_EN 0x00010000 /* enable link status from external LINK_0 and LINK_1 pins */ #define E1000_CTRL_SWDPIN0 0x00040000 /* SWDPIN 0 value */ #define E1000_CTRL_SWDPIN1 0x00080000 /* SWDPIN 1 value */ #define E1000_CTRL_SWDPIN2 0x00100000 /* SWDPIN 2 value */ @@ -1430,6 +1456,16 @@ struct e1000_hw { #define E1000_STATUS_BUS64 0x00001000 /* In 64 bit slot */ #define E1000_STATUS_PCIX_MODE 0x00002000 /* PCI-X mode */ #define E1000_STATUS_PCIX_SPEED 0x0000C000 /* PCI-X bus speed */ +#define E1000_STATUS_BMC_SKU_0 0x00100000 /* BMC USB redirect disabled */ +#define E1000_STATUS_BMC_SKU_1 0x00200000 /* BMC SRAM disabled */ +#define E1000_STATUS_BMC_SKU_2 0x00400000 /* BMC SDRAM disabled */ +#define E1000_STATUS_BMC_CRYPTO 0x00800000 /* BMC crypto disabled */ +#define E1000_STATUS_BMC_LITE 0x01000000 /* BMC external code execution disabled */ +#define E1000_STATUS_RGMII_ENABLE 0x02000000 /* RGMII disabled */ +#define E1000_STATUS_FUSE_8 0x04000000 +#define E1000_STATUS_FUSE_9 0x08000000 +#define E1000_STATUS_SERDES0_DIS 0x10000000 /* SERDES disabled on port 0 */ +#define E1000_STATUS_SERDES1_DIS 0x20000000 /* SERDES disabled on port 1 */ /* Constants used to intrepret the masked PCI-X bus speed. */ #define E1000_STATUS_PCIX_SPEED_66 0x00000000 /* PCI-X bus speed 50-66 MHz */ @@ -1507,6 +1543,8 @@ struct e1000_hw { #define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000 #define E1000_CTRL_EXT_LINK_MODE_GMII 0x00000000 #define E1000_CTRL_EXT_LINK_MODE_TBI 0x00C00000 +#define E1000_CTRL_EXT_LINK_MODE_KMRN 0x00000000 +#define E1000_CTRL_EXT_LINK_MODE_SERDES 0x00C00000 #define E1000_CTRL_EXT_WR_WMARK_MASK 0x03000000 #define E1000_CTRL_EXT_WR_WMARK_256 0x00000000 #define E1000_CTRL_EXT_WR_WMARK_320 0x01000000 @@ -1516,6 +1554,9 @@ struct e1000_hw { #define E1000_CTRL_EXT_DRV_LOAD 0x10000000 /* Driver loaded bit for FW */ #define E1000_CTRL_EXT_IAME 0x08000000 /* Interrupt acknowledge Auto-mask */ #define E1000_CTRL_EXT_INT_TIMER_CLR 0x20000000 /* Clear Interrupt timers after IMS clear */ +#define E1000_CRTL_EXT_PB_PAREN 0x01000000 /* packet buffer parity error detection enabled */ +#define E1000_CTRL_EXT_DF_PAREN 0x02000000 /* descriptor FIFO parity error detection enable */ +#define E1000_CTRL_EXT_GHOST_PAREN 0x40000000 /* MDI Control */ #define E1000_MDIC_DATA_MASK 0x0000FFFF @@ -1529,6 +1570,32 @@ struct e1000_hw { #define E1000_MDIC_INT_EN 0x20000000 #define E1000_MDIC_ERROR 0x40000000 +#define E1000_KUMCTRLSTA_MASK 0x0000FFFF +#define E1000_KUMCTRLSTA_OFFSET 0x001F0000 +#define E1000_KUMCTRLSTA_OFFSET_SHIFT 16 +#define E1000_KUMCTRLSTA_REN 0x00200000 + +#define E1000_KUMCTRLSTA_OFFSET_FIFO_CTRL 0x00000000 +#define E1000_KUMCTRLSTA_OFFSET_CTRL 0x00000001 +#define E1000_KUMCTRLSTA_OFFSET_INB_CTRL 0x00000002 +#define E1000_KUMCTRLSTA_OFFSET_DIAG 0x00000003 +#define E1000_KUMCTRLSTA_OFFSET_TIMEOUTS 0x00000004 +#define E1000_KUMCTRLSTA_OFFSET_INB_PARAM 0x00000009 +#define E1000_KUMCTRLSTA_OFFSET_HD_CTRL 0x00000010 +#define E1000_KUMCTRLSTA_OFFSET_M2P_SERDES 0x0000001E +#define E1000_KUMCTRLSTA_OFFSET_M2P_MODES 0x0000001F + +/* FIFO Control */ +#define E1000_KUMCTRLSTA_FIFO_CTRL_RX_BYPASS 0x00000008 +#define E1000_KUMCTRLSTA_FIFO_CTRL_TX_BYPASS 0x00000800 + +/* In-Band Control */ +#define E1000_KUMCTRLSTA_INB_CTRL_DIS_PADDING 0x00000010 + +/* Half-Duplex Control */ +#define E1000_KUMCTRLSTA_HD_CTRL_10_100_DEFAULT 0x00000004 +#define E1000_KUMCTRLSTA_HD_CTRL_1000_DEFAULT 0x00000000 + /* LED Control */ #define E1000_LEDCTL_LED0_MODE_MASK 0x0000000F #define E1000_LEDCTL_LED0_MODE_SHIFT 0 @@ -1591,6 +1658,13 @@ struct e1000_hw { #define E1000_ICR_MNG 0x00040000 /* Manageability event */ #define E1000_ICR_DOCK 0x00080000 /* Dock/Undock */ #define E1000_ICR_INT_ASSERTED 0x80000000 /* If this bit asserted, the driver should claim the interrupt */ +#define E1000_ICR_RXD_FIFO_PAR0 0x00100000 /* queue 0 Rx descriptor FIFO parity error */ +#define E1000_ICR_TXD_FIFO_PAR0 0x00200000 /* queue 0 Tx descriptor FIFO parity error */ +#define E1000_ICR_HOST_ARB_PAR 0x00400000 /* host arb read buffer parity error */ +#define E1000_ICR_PB_PAR 0x00800000 /* packet buffer parity error */ +#define E1000_ICR_RXD_FIFO_PAR1 0x01000000 /* queue 1 Rx descriptor FIFO parity error */ +#define E1000_ICR_TXD_FIFO_PAR1 0x02000000 /* queue 1 Tx descriptor FIFO parity error */ +#define E1000_ICR_ALL_PARITY 0x03F00000 /* all parity error bits */ /* Interrupt Cause Set */ #define E1000_ICS_TXDW E1000_ICR_TXDW /* Transmit desc written back */ @@ -1611,6 +1685,12 @@ struct e1000_hw { #define E1000_ICS_ACK E1000_ICR_ACK /* Receive Ack frame */ #define E1000_ICS_MNG E1000_ICR_MNG /* Manageability event */ #define E1000_ICS_DOCK E1000_ICR_DOCK /* Dock/Undock */ +#define E1000_ICS_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* queue 0 Rx descriptor FIFO parity error */ +#define E1000_ICS_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* queue 0 Tx descriptor FIFO parity error */ +#define E1000_ICS_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer parity error */ +#define E1000_ICS_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */ +#define E1000_ICS_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */ +#define E1000_ICS_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */ /* Interrupt Mask Set */ #define E1000_IMS_TXDW E1000_ICR_TXDW /* Transmit desc written back */ @@ -1631,6 +1711,12 @@ struct e1000_hw { #define E1000_IMS_ACK E1000_ICR_ACK /* Receive Ack frame */ #define E1000_IMS_MNG E1000_ICR_MNG /* Manageability event */ #define E1000_IMS_DOCK E1000_ICR_DOCK /* Dock/Undock */ +#define E1000_IMS_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* queue 0 Rx descriptor FIFO parity error */ +#define E1000_IMS_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* queue 0 Tx descriptor FIFO parity error */ +#define E1000_IMS_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer parity error */ +#define E1000_IMS_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */ +#define E1000_IMS_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */ +#define E1000_IMS_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */ /* Interrupt Mask Clear */ #define E1000_IMC_TXDW E1000_ICR_TXDW /* Transmit desc written back */ @@ -1651,6 +1737,12 @@ struct e1000_hw { #define E1000_IMC_ACK E1000_ICR_ACK /* Receive Ack frame */ #define E1000_IMC_MNG E1000_ICR_MNG /* Manageability event */ #define E1000_IMC_DOCK E1000_ICR_DOCK /* Dock/Undock */ +#define E1000_IMC_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* queue 0 Rx descriptor FIFO parity error */ +#define E1000_IMC_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* queue 0 Tx descriptor FIFO parity error */ +#define E1000_IMC_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer parity error */ +#define E1000_IMC_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */ +#define E1000_IMC_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */ +#define E1000_IMC_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */ /* Receive Control */ #define E1000_RCTL_RST 0x00000001 /* Software reset */ @@ -1720,6 +1812,12 @@ struct e1000_hw { #define E1000_PSRCTL_BSIZE2_SHIFT 6 /* Shift _left_ 6 */ #define E1000_PSRCTL_BSIZE3_SHIFT 14 /* Shift _left_ 14 */ +/* SW_W_SYNC definitions */ +#define E1000_SWFW_EEP_SM 0x0001 +#define E1000_SWFW_PHY0_SM 0x0002 +#define E1000_SWFW_PHY1_SM 0x0004 +#define E1000_SWFW_MAC_CSR_SM 0x0008 + /* Receive Descriptor */ #define E1000_RDT_DELAY 0x0000ffff /* Delay timer (1=1024us) */ #define E1000_RDT_FPDB 0x80000000 /* Flush descriptor block */ @@ -1798,6 +1896,11 @@ struct e1000_hw { #define E1000_TCTL_RTLC 0x01000000 /* Re-transmit on late collision */ #define E1000_TCTL_NRTU 0x02000000 /* No Re-transmit on underrun */ #define E1000_TCTL_MULR 0x10000000 /* Multiple request support */ +/* Extended Transmit Control */ +#define E1000_TCTL_EXT_BST_MASK 0x000003FF /* Backoff Slot Time */ +#define E1000_TCTL_EXT_GCEX_MASK 0x000FFC00 /* Gigabit Carry Extend Padding */ + +#define DEFAULT_80003ES2LAN_TCTL_EXT_GCEX 0x00010000 /* Receive Checksum Control */ #define E1000_RXCSUM_PCSS_MASK 0x000000FF /* Packet Checksum Start */ @@ -2044,6 +2147,7 @@ struct e1000_host_command_info { #define EEPROM_CHECKSUM_REG 0x003F #define E1000_EEPROM_CFG_DONE 0x00040000 /* MNG config cycle done */ +#define E1000_EEPROM_CFG_DONE_PORT_1 0x00080000 /* ...for second port */ /* Word definitions for ID LED Settings */ #define ID_LED_RESERVED_0000 0x0000 @@ -2132,8 +2236,11 @@ struct e1000_host_command_info { #define DEFAULT_82542_TIPG_IPGR2 10 #define DEFAULT_82543_TIPG_IPGR2 6 +#define DEFAULT_80003ES2LAN_TIPG_IPGR2 7 #define E1000_TIPG_IPGR2_SHIFT 20 +#define DEFAULT_80003ES2LAN_TIPG_IPGT_10_100 0x00000009 +#define DEFAULT_80003ES2LAN_TIPG_IPGT_1000 0x00000008 #define E1000_TXDMAC_DPP 0x00000001 /* Adaptive IFS defines */ @@ -2374,6 +2481,78 @@ struct e1000_host_command_info { #define IGP01E1000_ANALOG_REGS_PAGE 0x20C0 +/* Bits... + * 15-5: page + * 4-0: register offset + */ +#define GG82563_PAGE_SHIFT 5 +#define GG82563_REG(page, reg) \ + (((page) << GG82563_PAGE_SHIFT) | ((reg) & MAX_PHY_REG_ADDRESS)) +#define GG82563_MIN_ALT_REG 30 + +/* GG82563 Specific Registers */ +#define GG82563_PHY_SPEC_CTRL \ + GG82563_REG(0, 16) /* PHY Specific Control */ +#define GG82563_PHY_SPEC_STATUS \ + GG82563_REG(0, 17) /* PHY Specific Status */ +#define GG82563_PHY_INT_ENABLE \ + GG82563_REG(0, 18) /* Interrupt Enable */ +#define GG82563_PHY_SPEC_STATUS_2 \ + GG82563_REG(0, 19) /* PHY Specific Status 2 */ +#define GG82563_PHY_RX_ERR_CNTR \ + GG82563_REG(0, 21) /* Receive Error Counter */ +#define GG82563_PHY_PAGE_SELECT \ + GG82563_REG(0, 22) /* Page Select */ +#define GG82563_PHY_SPEC_CTRL_2 \ + GG82563_REG(0, 26) /* PHY Specific Control 2 */ +#define GG82563_PHY_PAGE_SELECT_ALT \ + GG82563_REG(0, 29) /* Alternate Page Select */ +#define GG82563_PHY_TEST_CLK_CTRL \ + GG82563_REG(0, 30) /* Test Clock Control (use reg. 29 to select) */ + +#define GG82563_PHY_MAC_SPEC_CTRL \ + GG82563_REG(2, 21) /* MAC Specific Control Register */ +#define GG82563_PHY_MAC_SPEC_CTRL_2 \ + GG82563_REG(2, 26) /* MAC Specific Control 2 */ + +#define GG82563_PHY_DSP_DISTANCE \ + GG82563_REG(5, 26) /* DSP Distance */ + +/* Page 193 - Port Control Registers */ +#define GG82563_PHY_KMRN_MODE_CTRL \ + GG82563_REG(193, 16) /* Kumeran Mode Control */ +#define GG82563_PHY_PORT_RESET \ + GG82563_REG(193, 17) /* Port Reset */ +#define GG82563_PHY_REVISION_ID \ + GG82563_REG(193, 18) /* Revision ID */ +#define GG82563_PHY_DEVICE_ID \ + GG82563_REG(193, 19) /* Device ID */ +#define GG82563_PHY_PWR_MGMT_CTRL \ + GG82563_REG(193, 20) /* Power Management Control */ +#define GG82563_PHY_RATE_ADAPT_CTRL \ + GG82563_REG(193, 25) /* Rate Adaptation Control */ + +/* Page 194 - KMRN Registers */ +#define GG82563_PHY_KMRN_FIFO_CTRL_STAT \ + GG82563_REG(194, 16) /* FIFO's Control/Status */ +#define GG82563_PHY_KMRN_CTRL \ + GG82563_REG(194, 17) /* Control */ +#define GG82563_PHY_INBAND_CTRL \ + GG82563_REG(194, 18) /* Inband Control */ +#define GG82563_PHY_KMRN_DIAGNOSTIC \ + GG82563_REG(194, 19) /* Diagnostic */ +#define GG82563_PHY_ACK_TIMEOUTS \ + GG82563_REG(194, 20) /* Acknowledge Timeouts */ +#define GG82563_PHY_ADV_ABILITY \ + GG82563_REG(194, 21) /* Advertised Ability */ +#define GG82563_PHY_LINK_PARTNER_ADV_ABILITY \ + GG82563_REG(194, 23) /* Link Partner Advertised Ability */ +#define GG82563_PHY_ADV_NEXT_PAGE \ + GG82563_REG(194, 24) /* Advertised Next Page */ +#define GG82563_PHY_LINK_PARTNER_ADV_NEXT_PAGE \ + GG82563_REG(194, 25) /* Link Partner Advertised Next page */ +#define GG82563_PHY_KMRN_MISC \ + GG82563_REG(194, 26) /* Misc. */ /* PHY Control Register */ #define MII_CR_SPEED_SELECT_MSB 0x0040 /* bits 6,13: 10=1000, 01=100, 00=10 */ @@ -2687,6 +2866,113 @@ struct e1000_host_command_info { #define IGP01E1000_ANALOG_FUSE_FINE_1 0x0080 #define IGP01E1000_ANALOG_FUSE_FINE_10 0x0500 +/* GG82563 PHY Specific Status Register (Page 0, Register 16 */ +#define GG82563_PSCR_DISABLE_JABBER 0x0001 /* 1=Disable Jabber */ +#define GG82563_PSCR_POLARITY_REVERSAL_DISABLE 0x0002 /* 1=Polarity Reversal Disabled */ +#define GG82563_PSCR_POWER_DOWN 0x0004 /* 1=Power Down */ +#define GG82563_PSCR_COPPER_TRANSMITER_DISABLE 0x0008 /* 1=Transmitter Disabled */ +#define GG82563_PSCR_CROSSOVER_MODE_MASK 0x0060 +#define GG82563_PSCR_CROSSOVER_MODE_MDI 0x0000 /* 00=Manual MDI configuration */ +#define GG82563_PSCR_CROSSOVER_MODE_MDIX 0x0020 /* 01=Manual MDIX configuration */ +#define GG82563_PSCR_CROSSOVER_MODE_AUTO 0x0060 /* 11=Automatic crossover */ +#define GG82563_PSCR_ENALBE_EXTENDED_DISTANCE 0x0080 /* 1=Enable Extended Distance */ +#define GG82563_PSCR_ENERGY_DETECT_MASK 0x0300 +#define GG82563_PSCR_ENERGY_DETECT_OFF 0x0000 /* 00,01=Off */ +#define GG82563_PSCR_ENERGY_DETECT_RX 0x0200 /* 10=Sense on Rx only (Energy Detect) */ +#define GG82563_PSCR_ENERGY_DETECT_RX_TM 0x0300 /* 11=Sense and Tx NLP */ +#define GG82563_PSCR_FORCE_LINK_GOOD 0x0400 /* 1=Force Link Good */ +#define GG82563_PSCR_DOWNSHIFT_ENABLE 0x0800 /* 1=Enable Downshift */ +#define GG82563_PSCR_DOWNSHIFT_COUNTER_MASK 0x7000 +#define GG82563_PSCR_DOWNSHIFT_COUNTER_SHIFT 12 + +/* PHY Specific Status Register (Page 0, Register 17) */ +#define GG82563_PSSR_JABBER 0x0001 /* 1=Jabber */ +#define GG82563_PSSR_POLARITY 0x0002 /* 1=Polarity Reversed */ +#define GG82563_PSSR_LINK 0x0008 /* 1=Link is Up */ +#define GG82563_PSSR_ENERGY_DETECT 0x0010 /* 1=Sleep, 0=Active */ +#define GG82563_PSSR_DOWNSHIFT 0x0020 /* 1=Downshift */ +#define GG82563_PSSR_CROSSOVER_STATUS 0x0040 /* 1=MDIX, 0=MDI */ +#define GG82563_PSSR_RX_PAUSE_ENABLED 0x0100 /* 1=Receive Pause Enabled */ +#define GG82563_PSSR_TX_PAUSE_ENABLED 0x0200 /* 1=Transmit Pause Enabled */ +#define GG82563_PSSR_LINK_UP 0x0400 /* 1=Link Up */ +#define GG82563_PSSR_SPEED_DUPLEX_RESOLVED 0x0800 /* 1=Resolved */ +#define GG82563_PSSR_PAGE_RECEIVED 0x1000 /* 1=Page Received */ +#define GG82563_PSSR_DUPLEX 0x2000 /* 1-Full-Duplex */ +#define GG82563_PSSR_SPEED_MASK 0xC000 +#define GG82563_PSSR_SPEED_10MBPS 0x0000 /* 00=10Mbps */ +#define GG82563_PSSR_SPEED_100MBPS 0x4000 /* 01=100Mbps */ +#define GG82563_PSSR_SPEED_1000MBPS 0x8000 /* 10=1000Mbps */ + +/* PHY Specific Status Register 2 (Page 0, Register 19) */ +#define GG82563_PSSR2_JABBER 0x0001 /* 1=Jabber */ +#define GG82563_PSSR2_POLARITY_CHANGED 0x0002 /* 1=Polarity Changed */ +#define GG82563_PSSR2_ENERGY_DETECT_CHANGED 0x0010 /* 1=Energy Detect Changed */ +#define GG82563_PSSR2_DOWNSHIFT_INTERRUPT 0x0020 /* 1=Downshift Detected */ +#define GG82563_PSSR2_MDI_CROSSOVER_CHANGE 0x0040 /* 1=Crossover Changed */ +#define GG82563_PSSR2_FALSE_CARRIER 0x0100 /* 1=False Carrier */ +#define GG82563_PSSR2_SYMBOL_ERROR 0x0200 /* 1=Symbol Error */ +#define GG82563_PSSR2_LINK_STATUS_CHANGED 0x0400 /* 1=Link Status Changed */ +#define GG82563_PSSR2_AUTO_NEG_COMPLETED 0x0800 /* 1=Auto-Neg Completed */ +#define GG82563_PSSR2_PAGE_RECEIVED 0x1000 /* 1=Page Received */ +#define GG82563_PSSR2_DUPLEX_CHANGED 0x2000 /* 1=Duplex Changed */ +#define GG82563_PSSR2_SPEED_CHANGED 0x4000 /* 1=Speed Changed */ +#define GG82563_PSSR2_AUTO_NEG_ERROR 0x8000 /* 1=Auto-Neg Error */ + +/* PHY Specific Control Register 2 (Page 0, Register 26) */ +#define GG82563_PSCR2_10BT_POLARITY_FORCE 0x0002 /* 1=Force Negative Polarity */ +#define GG82563_PSCR2_1000MB_TEST_SELECT_MASK 0x000C +#define GG82563_PSCR2_1000MB_TEST_SELECT_NORMAL 0x0000 /* 00,01=Normal Operation */ +#define GG82563_PSCR2_1000MB_TEST_SELECT_112NS 0x0008 /* 10=Select 112ns Sequence */ +#define GG82563_PSCR2_1000MB_TEST_SELECT_16NS 0x000C /* 11=Select 16ns Sequence */ +#define GG82563_PSCR2_REVERSE_AUTO_NEG 0x2000 /* 1=Reverse Auto-Negotiation */ +#define GG82563_PSCR2_1000BT_DISABLE 0x4000 /* 1=Disable 1000BASE-T */ +#define GG82563_PSCR2_TRANSMITER_TYPE_MASK 0x8000 +#define GG82563_PSCR2_TRANSMITTER_TYPE_CLASS_B 0x0000 /* 0=Class B */ +#define GG82563_PSCR2_TRANSMITTER_TYPE_CLASS_A 0x8000 /* 1=Class A */ + +/* MAC Specific Control Register (Page 2, Register 21) */ +/* Tx clock speed for Link Down and 1000BASE-T for the following speeds */ +#define GG82563_MSCR_TX_CLK_MASK 0x0007 +#define GG82563_MSCR_TX_CLK_10MBPS_2_5MHZ 0x0004 +#define GG82563_MSCR_TX_CLK_100MBPS_25MHZ 0x0005 +#define GG82563_MSCR_TX_CLK_1000MBPS_2_5MHZ 0x0006 +#define GG82563_MSCR_TX_CLK_1000MBPS_25MHZ 0x0007 + +#define GG82563_MSCR_ASSERT_CRS_ON_TX 0x0010 /* 1=Assert */ + +/* DSP Distance Register (Page 5, Register 26) */ +#define GG82563_DSPD_CABLE_LENGTH 0x0007 /* 0 = <50M; + 1 = 50-80M; + 2 = 80-110M; + 3 = 110-140M; + 4 = >140M */ + +/* Kumeran Mode Control Register (Page 193, Register 16) */ +#define GG82563_KMCR_PHY_LEDS_EN 0x0020 /* 1=PHY LEDs, 0=Kumeran Inband LEDs */ +#define GG82563_KMCR_FORCE_LINK_UP 0x0040 /* 1=Force Link Up */ +#define GG82563_KMCR_SUPPRESS_SGMII_EPD_EXT 0x0080 +#define GG82563_KMCR_MDIO_BUS_SPEED_SELECT_MASK 0x0400 +#define GG82563_KMCR_MDIO_BUS_SPEED_SELECT 0x0400 /* 1=6.25MHz, 0=0.8MHz */ +#define GG82563_KMCR_PASS_FALSE_CARRIER 0x0800 + +/* Power Management Control Register (Page 193, Register 20) */ +#define GG82563_PMCR_ENABLE_ELECTRICAL_IDLE 0x0001 /* 1=Enalbe SERDES Electrical Idle */ +#define GG82563_PMCR_DISABLE_PORT 0x0002 /* 1=Disable Port */ +#define GG82563_PMCR_DISABLE_SERDES 0x0004 /* 1=Disable SERDES */ +#define GG82563_PMCR_REVERSE_AUTO_NEG 0x0008 /* 1=Enable Reverse Auto-Negotiation */ +#define GG82563_PMCR_DISABLE_1000_NON_D0 0x0010 /* 1=Disable 1000Mbps Auto-Neg in non D0 */ +#define GG82563_PMCR_DISABLE_1000 0x0020 /* 1=Disable 1000Mbps Auto-Neg Always */ +#define GG82563_PMCR_REVERSE_AUTO_NEG_D0A 0x0040 /* 1=Enable D0a Reverse Auto-Negotiation */ +#define GG82563_PMCR_FORCE_POWER_STATE 0x0080 /* 1=Force Power State */ +#define GG82563_PMCR_PROGRAMMED_POWER_STATE_MASK 0x0300 +#define GG82563_PMCR_PROGRAMMED_POWER_STATE_DR 0x0000 /* 00=Dr */ +#define GG82563_PMCR_PROGRAMMED_POWER_STATE_D0U 0x0100 /* 01=D0u */ +#define GG82563_PMCR_PROGRAMMED_POWER_STATE_D0A 0x0200 /* 10=D0a */ +#define GG82563_PMCR_PROGRAMMED_POWER_STATE_D3 0x0300 /* 11=D3 */ + +/* In-Band Control Register (Page 194, Register 18) */ +#define GG82563_ICR_DIS_PADDING 0x0010 /* Disable Padding Use */ + /* Bit definitions for valid PHY IDs. */ /* I = Integrated @@ -2701,6 +2987,7 @@ struct e1000_host_command_info { #define M88E1011_I_REV_4 0x04 #define M88E1111_I_PHY_ID 0x01410CC0 #define L1LXT971A_PHY_ID 0x001378E0 +#define GG82563_E_PHY_ID 0x01410CA0 /* Miscellaneous PHY bit definitions. */ #define PHY_PREAMBLE 0xFFFFFFFF diff --git a/drivers/net/e1000/e1000_main.c b/drivers/net/e1000/e1000_main.c index e80378a220d..3acbffd5bde 100644 --- a/drivers/net/e1000/e1000_main.c +++ b/drivers/net/e1000/e1000_main.c @@ -157,9 +157,12 @@ static struct pci_device_id e1000_pci_tbl[] = { INTEL_E1000_ETHERNET_DEVICE(0x108A), INTEL_E1000_ETHERNET_DEVICE(0x108B), INTEL_E1000_ETHERNET_DEVICE(0x108C), + INTEL_E1000_ETHERNET_DEVICE(0x1096), + INTEL_E1000_ETHERNET_DEVICE(0x1098), INTEL_E1000_ETHERNET_DEVICE(0x1099), INTEL_E1000_ETHERNET_DEVICE(0x109A), INTEL_E1000_ETHERNET_DEVICE(0x10B5), + INTEL_E1000_ETHERNET_DEVICE(0x10B9), /* required last entry */ {0,} }; @@ -575,6 +578,7 @@ e1000_reset(struct e1000_adapter *adapter) break; case e1000_82571: case e1000_82572: + case e1000_80003es2lan: pba = E1000_PBA_38K; break; case e1000_82573: @@ -852,6 +856,7 @@ e1000_probe(struct pci_dev *pdev, case e1000_82546: case e1000_82546_rev_3: case e1000_82571: + case e1000_80003es2lan: if (E1000_READ_REG(&adapter->hw, STATUS) & E1000_STATUS_FUNC_1){ e1000_read_eeprom(&adapter->hw, EEPROM_INIT_CONTROL3_PORT_B, 1, &eeprom_data); |