diff options
Diffstat (limited to 'drivers/net/e1000e/ich8lan.c')
| -rw-r--r-- | drivers/net/e1000e/ich8lan.c | 482 |
1 files changed, 387 insertions, 95 deletions
diff --git a/drivers/net/e1000e/ich8lan.c b/drivers/net/e1000e/ich8lan.c index b6388b9535f..51ddb04ab19 100644 --- a/drivers/net/e1000e/ich8lan.c +++ b/drivers/net/e1000e/ich8lan.c @@ -124,11 +124,25 @@ #define SW_FLAG_TIMEOUT 1000 /* SW Semaphore flag timeout in milliseconds */ +/* SMBus Address Phy Register */ +#define HV_SMB_ADDR PHY_REG(768, 26) +#define HV_SMB_ADDR_PEC_EN 0x0200 +#define HV_SMB_ADDR_VALID 0x0080 + +/* Strapping Option Register - RO */ +#define E1000_STRAP 0x0000C +#define E1000_STRAP_SMBUS_ADDRESS_MASK 0x00FE0000 +#define E1000_STRAP_SMBUS_ADDRESS_SHIFT 17 + /* OEM Bits Phy Register */ #define HV_OEM_BITS PHY_REG(768, 25) #define HV_OEM_BITS_LPLU 0x0004 /* Low Power Link Up */ +#define HV_OEM_BITS_GBE_DIS 0x0040 /* Gigabit Disable */ #define HV_OEM_BITS_RESTART_AN 0x0400 /* Restart Auto-negotiation */ +#define E1000_NVM_K1_CONFIG 0x1B /* NVM K1 Config Word */ +#define E1000_NVM_K1_ENABLE 0x1 /* NVM Enable K1 bit */ + /* ICH GbE Flash Hardware Sequencing Flash Status Register bit breakdown */ /* Offset 04h HSFSTS */ union ich8_hws_flash_status { @@ -208,6 +222,9 @@ static s32 e1000_cleanup_led_pchlan(struct e1000_hw *hw); static s32 e1000_led_on_pchlan(struct e1000_hw *hw); static s32 e1000_led_off_pchlan(struct e1000_hw *hw); static s32 e1000_set_lplu_state_pchlan(struct e1000_hw *hw, bool active); +static void e1000_lan_init_done_ich8lan(struct e1000_hw *hw); +static s32 e1000_k1_gig_workaround_hv(struct e1000_hw *hw, bool link); +static s32 e1000_configure_k1_ich8lan(struct e1000_hw *hw, bool k1_enable); static inline u16 __er16flash(struct e1000_hw *hw, unsigned long reg) { @@ -483,14 +500,6 @@ static s32 e1000_check_for_copper_link_ich8lan(struct e1000_hw *hw) goto out; } - if (hw->mac.type == e1000_pchlan) { - ret_val = e1000e_write_kmrn_reg(hw, - E1000_KMRNCTRLSTA_K1_CONFIG, - E1000_KMRNCTRLSTA_K1_ENABLE); - if (ret_val) - goto out; - } - /* * First we want to see if the MII Status Register reports * link. If so, then we want to get the current speed/duplex @@ -500,6 +509,12 @@ static s32 e1000_check_for_copper_link_ich8lan(struct e1000_hw *hw) if (ret_val) goto out; + if (hw->mac.type == e1000_pchlan) { + ret_val = e1000_k1_gig_workaround_hv(hw, link); + if (ret_val) + goto out; + } + if (!link) goto out; /* No link detected */ @@ -794,6 +809,326 @@ static s32 e1000_phy_force_speed_duplex_ich8lan(struct e1000_hw *hw) } /** + * e1000_sw_lcd_config_ich8lan - SW-based LCD Configuration + * @hw: pointer to the HW structure + * + * SW should configure the LCD from the NVM extended configuration region + * as a workaround for certain parts. + **/ +static s32 e1000_sw_lcd_config_ich8lan(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + u32 i, data, cnf_size, cnf_base_addr, sw_cfg_mask; + s32 ret_val; + u16 word_addr, reg_data, reg_addr, phy_page = 0; + + ret_val = hw->phy.ops.acquire_phy(hw); + if (ret_val) + return ret_val; + + /* + * Initialize the PHY from the NVM on ICH platforms. This + * is needed due to an issue where the NVM configuration is + * not properly autoloaded after power transitions. + * Therefore, after each PHY reset, we will load the + * configuration data out of the NVM manually. + */ + if ((hw->mac.type == e1000_ich8lan && phy->type == e1000_phy_igp_3) || + (hw->mac.type == e1000_pchlan)) { + struct e1000_adapter *adapter = hw->adapter; + + /* Check if SW needs to configure the PHY */ + if ((adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M_AMT) || + (adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M) || + (hw->mac.type == e1000_pchlan)) + sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG_ICH8M; + else + sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG; + + data = er32(FEXTNVM); + if (!(data & sw_cfg_mask)) + goto out; + + /* Wait for basic configuration completes before proceeding */ + e1000_lan_init_done_ich8lan(hw); + + /* + * Make sure HW does not configure LCD from PHY + * extended configuration before SW configuration + */ + data = er32(EXTCNF_CTRL); + if (data & E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE) + goto out; + + cnf_size = er32(EXTCNF_SIZE); + cnf_size &= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK; + cnf_size >>= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT; + if (!cnf_size) + goto out; + + cnf_base_addr = data & E1000_EXTCNF_CTRL_EXT_CNF_POINTER_MASK; + cnf_base_addr >>= E1000_EXTCNF_CTRL_EXT_CNF_POINTER_SHIFT; + + if (!(data & E1000_EXTCNF_CTRL_OEM_WRITE_ENABLE) && + (hw->mac.type == e1000_pchlan)) { + /* + * HW configures the SMBus address and LEDs when the + * OEM and LCD Write Enable bits are set in the NVM. + * When both NVM bits are cleared, SW will configure + * them instead. + */ + data = er32(STRAP); + data &= E1000_STRAP_SMBUS_ADDRESS_MASK; + reg_data = data >> E1000_STRAP_SMBUS_ADDRESS_SHIFT; + reg_data |= HV_SMB_ADDR_PEC_EN | HV_SMB_ADDR_VALID; + ret_val = e1000_write_phy_reg_hv_locked(hw, HV_SMB_ADDR, + reg_data); + if (ret_val) + goto out; + + data = er32(LEDCTL); + ret_val = e1000_write_phy_reg_hv_locked(hw, + HV_LED_CONFIG, + (u16)data); + if (ret_val) + goto out; + } + /* Configure LCD from extended configuration region. */ + + /* cnf_base_addr is in DWORD */ + word_addr = (u16)(cnf_base_addr << 1); + + for (i = 0; i < cnf_size; i++) { + ret_val = e1000_read_nvm(hw, (word_addr + i * 2), 1, + ®_data); + if (ret_val) + goto out; + + ret_val = e1000_read_nvm(hw, (word_addr + i * 2 + 1), + 1, ®_addr); + if (ret_val) + goto out; + + /* Save off the PHY page for future writes. */ + if (reg_addr == IGP01E1000_PHY_PAGE_SELECT) { + phy_page = reg_data; + continue; + } + + reg_addr &= PHY_REG_MASK; + reg_addr |= phy_page; + + ret_val = phy->ops.write_phy_reg_locked(hw, + (u32)reg_addr, + reg_data); + if (ret_val) + goto out; + } + } + +out: + hw->phy.ops.release_phy(hw); + return ret_val; +} + +/** + * e1000_k1_gig_workaround_hv - K1 Si workaround + * @hw: pointer to the HW structure + * @link: link up bool flag + * + * If K1 is enabled for 1Gbps, the MAC might stall when transitioning + * from a lower speed. This workaround disables K1 whenever link is at 1Gig + * If link is down, the function will restore the default K1 setting located + * in the NVM. + **/ +static s32 e1000_k1_gig_workaround_hv(struct e1000_hw *hw, bool link) +{ + s32 ret_val = 0; + u16 status_reg = 0; + bool k1_enable = hw->dev_spec.ich8lan.nvm_k1_enabled; + + if (hw->mac.type != e1000_pchlan) + goto out; + + /* Wrap the whole flow with the sw flag */ + ret_val = hw->phy.ops.acquire_phy(hw); + if (ret_val) + goto out; + + /* Disable K1 when link is 1Gbps, otherwise use the NVM setting */ + if (link) { + if (hw->phy.type == e1000_phy_82578) { + ret_val = hw->phy.ops.read_phy_reg_locked(hw, + BM_CS_STATUS, + &status_reg); + if (ret_val) + goto release; + + status_reg &= BM_CS_STATUS_LINK_UP | + BM_CS_STATUS_RESOLVED | + BM_CS_STATUS_SPEED_MASK; + + if (status_reg == (BM_CS_STATUS_LINK_UP | + BM_CS_STATUS_RESOLVED | + BM_CS_STATUS_SPEED_1000)) + k1_enable = false; + } + + if (hw->phy.type == e1000_phy_82577) { + ret_val = hw->phy.ops.read_phy_reg_locked(hw, + HV_M_STATUS, + &status_reg); + if (ret_val) + goto release; + + status_reg &= HV_M_STATUS_LINK_UP | + HV_M_STATUS_AUTONEG_COMPLETE | + HV_M_STATUS_SPEED_MASK; + + if (status_reg == (HV_M_STATUS_LINK_UP | + HV_M_STATUS_AUTONEG_COMPLETE | + HV_M_STATUS_SPEED_1000)) + k1_enable = false; + } + + /* Link stall fix for link up */ + ret_val = hw->phy.ops.write_phy_reg_locked(hw, PHY_REG(770, 19), + 0x0100); + if (ret_val) + goto release; + + } else { + /* Link stall fix for link down */ + ret_val = hw->phy.ops.write_phy_reg_locked(hw, PHY_REG(770, 19), + 0x4100); + if (ret_val) + goto release; + } + + ret_val = e1000_configure_k1_ich8lan(hw, k1_enable); + +release: + hw->phy.ops.release_phy(hw); +out: + return ret_val; +} + +/** + * e1000_configure_k1_ich8lan - Configure K1 power state + * @hw: pointer to the HW structure + * @enable: K1 state to configure + * + * Configure the K1 power state based on the provided parameter. + * Assumes semaphore already acquired. + * + * Success returns 0, Failure returns -E1000_ERR_PHY (-2) + **/ +static s32 e1000_configure_k1_ich8lan(struct e1000_hw *hw, bool k1_enable) +{ + s32 ret_val = 0; + u32 ctrl_reg = 0; + u32 ctrl_ext = 0; + u32 reg = 0; + u16 kmrn_reg = 0; + + ret_val = e1000e_read_kmrn_reg_locked(hw, + E1000_KMRNCTRLSTA_K1_CONFIG, + &kmrn_reg); + if (ret_val) + goto out; + + if (k1_enable) + kmrn_reg |= E1000_KMRNCTRLSTA_K1_ENABLE; + else + kmrn_reg &= ~E1000_KMRNCTRLSTA_K1_ENABLE; + + ret_val = e1000e_write_kmrn_reg_locked(hw, + E1000_KMRNCTRLSTA_K1_CONFIG, + kmrn_reg); + if (ret_val) + goto out; + + udelay(20); + ctrl_ext = er32(CTRL_EXT); + ctrl_reg = er32(CTRL); + + reg = ctrl_reg & ~(E1000_CTRL_SPD_1000 | E1000_CTRL_SPD_100); + reg |= E1000_CTRL_FRCSPD; + ew32(CTRL, reg); + + ew32(CTRL_EXT, ctrl_ext | E1000_CTRL_EXT_SPD_BYPS); + udelay(20); + ew32(CTRL, ctrl_reg); + ew32(CTRL_EXT, ctrl_ext); + udelay(20); + +out: + return ret_val; +} + +/** + * e1000_oem_bits_config_ich8lan - SW-based LCD Configuration + * @hw: pointer to the HW structure + * @d0_state: boolean if entering d0 or d3 device state + * + * SW will configure Gbe Disable and LPLU based on the NVM. The four bits are + * collectively called OEM bits. The OEM Write Enable bit and SW Config bit + * in NVM determines whether HW should configure LPLU and Gbe Disable. + **/ +static s32 e1000_oem_bits_config_ich8lan(struct e1000_hw *hw, bool d0_state) +{ + s32 ret_val = 0; + u32 mac_reg; + u16 oem_reg; + + if (hw->mac.type != e1000_pchlan) + return ret_val; + + ret_val = hw->phy.ops.acquire_phy(hw); + if (ret_val) + return ret_val; + + mac_reg = er32(EXTCNF_CTRL); + if (mac_reg & E1000_EXTCNF_CTRL_OEM_WRITE_ENABLE) + goto out; + + mac_reg = er32(FEXTNVM); + if (!(mac_reg & E1000_FEXTNVM_SW_CONFIG_ICH8M)) + goto out; + + mac_reg = er32(PHY_CTRL); + + ret_val = hw->phy.ops.read_phy_reg_locked(hw, HV_OEM_BITS, &oem_reg); + if (ret_val) + goto out; + + oem_reg &= ~(HV_OEM_BITS_GBE_DIS | HV_OEM_BITS_LPLU); + + if (d0_state) { + if (mac_reg & E1000_PHY_CTRL_GBE_DISABLE) + oem_reg |= HV_OEM_BITS_GBE_DIS; + + if (mac_reg & E1000_PHY_CTRL_D0A_LPLU) + oem_reg |= HV_OEM_BITS_LPLU; + } else { + if (mac_reg & E1000_PHY_CTRL_NOND0A_GBE_DISABLE) + oem_reg |= HV_OEM_BITS_GBE_DIS; + + if (mac_reg & E1000_PHY_CTRL_NOND0A_LPLU) + oem_reg |= HV_OEM_BITS_LPLU; + } + /* Restart auto-neg to activate the bits */ + oem_reg |= HV_OEM_BITS_RESTART_AN; + ret_val = hw->phy.ops.write_phy_reg_locked(hw, HV_OEM_BITS, oem_reg); + +out: + hw->phy.ops.release_phy(hw); + + return ret_val; +} + + +/** * e1000_hv_phy_workarounds_ich8lan - A series of Phy workarounds to be * done after every PHY reset. **/ @@ -833,10 +1168,20 @@ static s32 e1000_hv_phy_workarounds_ich8lan(struct e1000_hw *hw) ret_val = hw->phy.ops.acquire_phy(hw); if (ret_val) return ret_val; + hw->phy.addr = 1; - e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT, 0); + ret_val = e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT, 0); + if (ret_val) + goto out; hw->phy.ops.release_phy(hw); + /* + * Configure the K1 Si workaround during phy reset assuming there is + * link so that it disables K1 if link is in 1Gbps. + */ + ret_val = e1000_k1_gig_workaround_hv(hw, true); + +out: return ret_val; } @@ -882,11 +1227,8 @@ static void e1000_lan_init_done_ich8lan(struct e1000_hw *hw) **/ static s32 e1000_phy_hw_reset_ich8lan(struct e1000_hw *hw) { - struct e1000_phy_info *phy = &hw->phy; - u32 i; - u32 data, cnf_size, cnf_base_addr, sw_cfg_mask; - s32 ret_val; - u16 reg, word_addr, reg_data, reg_addr, phy_page = 0; + s32 ret_val = 0; + u16 reg; ret_val = e1000e_phy_hw_reset_generic(hw); if (ret_val) @@ -905,81 +1247,16 @@ static s32 e1000_phy_hw_reset_ich8lan(struct e1000_hw *hw) if (hw->mac.type == e1000_pchlan) e1e_rphy(hw, BM_WUC, ®); - /* - * Initialize the PHY from the NVM on ICH platforms. This - * is needed due to an issue where the NVM configuration is - * not properly autoloaded after power transitions. - * Therefore, after each PHY reset, we will load the - * configuration data out of the NVM manually. - */ - if (hw->mac.type == e1000_ich8lan && phy->type == e1000_phy_igp_3) { - struct e1000_adapter *adapter = hw->adapter; - - /* Check if SW needs configure the PHY */ - if ((adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M_AMT) || - (adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M)) - sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG_ICH8M; - else - sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG; - - data = er32(FEXTNVM); - if (!(data & sw_cfg_mask)) - return 0; - - /* Wait for basic configuration completes before proceeding */ - e1000_lan_init_done_ich8lan(hw); - - /* - * Make sure HW does not configure LCD from PHY - * extended configuration before SW configuration - */ - data = er32(EXTCNF_CTRL); - if (data & E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE) - return 0; - - cnf_size = er32(EXTCNF_SIZE); - cnf_size &= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK; - cnf_size >>= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT; - if (!cnf_size) - return 0; - - cnf_base_addr = data & E1000_EXTCNF_CTRL_EXT_CNF_POINTER_MASK; - cnf_base_addr >>= E1000_EXTCNF_CTRL_EXT_CNF_POINTER_SHIFT; - - /* Configure LCD from extended configuration region. */ - - /* cnf_base_addr is in DWORD */ - word_addr = (u16)(cnf_base_addr << 1); - - for (i = 0; i < cnf_size; i++) { - ret_val = e1000_read_nvm(hw, - (word_addr + i * 2), - 1, - ®_data); - if (ret_val) - return ret_val; - - ret_val = e1000_read_nvm(hw, - (word_addr + i * 2 + 1), - 1, - ®_addr); - if (ret_val) - return ret_val; - - /* Save off the PHY page for future writes. */ - if (reg_addr == IGP01E1000_PHY_PAGE_SELECT) { - phy_page = reg_data; - continue; - } - - reg_addr |= phy_page; + /* Configure the LCD with the extended configuration region in NVM */ + ret_val = e1000_sw_lcd_config_ich8lan(hw); + if (ret_val) + goto out; - ret_val = e1e_wphy(hw, (u32)reg_addr, reg_data); - if (ret_val) - return ret_val; - } - } + /* Configure the LCD with the OEM bits in NVM */ + if (hw->mac.type == e1000_pchlan) + ret_val = e1000_oem_bits_config_ich8lan(hw, true); +out: return 0; } @@ -2306,6 +2583,7 @@ static s32 e1000_get_bus_info_ich8lan(struct e1000_hw *hw) **/ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw) { + struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan; u16 reg; u32 ctrl, icr, kab; s32 ret_val; @@ -2341,6 +2619,18 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw) ew32(PBS, E1000_PBS_16K); } + if (hw->mac.type == e1000_pchlan) { + /* Save the NVM K1 bit setting*/ + ret_val = e1000_read_nvm(hw, E1000_NVM_K1_CONFIG, 1, ®); + if (ret_val) + return ret_val; + + if (reg & E1000_NVM_K1_ENABLE) + dev_spec->nvm_k1_enabled = true; + else + dev_spec->nvm_k1_enabled = false; + } + ctrl = er32(CTRL); if (!e1000_check_reset_block(hw)) { @@ -2386,6 +2676,15 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw) if (hw->mac.type == e1000_pchlan) e1e_rphy(hw, BM_WUC, ®); + ret_val = e1000_sw_lcd_config_ich8lan(hw); + if (ret_val) + goto out; + + if (hw->mac.type == e1000_pchlan) { + ret_val = e1000_oem_bits_config_ich8lan(hw, true); + if (ret_val) + goto out; + } /* * For PCH, this write will make sure that any noise * will be detected as a CRC error and be dropped rather than show up @@ -2404,6 +2703,7 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw) if (hw->mac.type == e1000_pchlan) ret_val = e1000_hv_phy_workarounds_ich8lan(hw); +out: return ret_val; } @@ -2708,14 +3008,6 @@ static s32 e1000_get_link_up_info_ich8lan(struct e1000_hw *hw, u16 *speed, if (ret_val) return ret_val; - if ((hw->mac.type == e1000_pchlan) && (*speed == SPEED_1000)) { - ret_val = e1000e_write_kmrn_reg(hw, - E1000_KMRNCTRLSTA_K1_CONFIG, - E1000_KMRNCTRLSTA_K1_DISABLE); - if (ret_val) - return ret_val; - } - if ((hw->mac.type == e1000_ich8lan) && (hw->phy.type == e1000_phy_igp_3) && (*speed == SPEED_1000)) { |