diff options
Diffstat (limited to 'drivers/net/e1000e/lib.c')
| -rw-r--r-- | drivers/net/e1000e/lib.c | 18 |
1 files changed, 8 insertions, 10 deletions
diff --git a/drivers/net/e1000e/lib.c b/drivers/net/e1000e/lib.c index 96921de5df2..dd8ab05b559 100644 --- a/drivers/net/e1000e/lib.c +++ b/drivers/net/e1000e/lib.c @@ -144,7 +144,7 @@ void e1000_write_vfta_generic(struct e1000_hw *hw, u32 offset, u32 value) * @hw: pointer to the HW structure * @rar_count: receive address registers * - * Setups the receive address registers by setting the base receive address + * Setup the receive address registers by setting the base receive address * register to the devices MAC address and clearing all the other receive * address registers to 0. **/ @@ -868,7 +868,7 @@ static s32 e1000_poll_fiber_serdes_link_generic(struct e1000_hw *hw) * milliseconds even if the other end is doing it in SW). */ for (i = 0; i < FIBER_LINK_UP_LIMIT; i++) { - msleep(10); + usleep_range(10000, 20000); status = er32(STATUS); if (status & E1000_STATUS_LU) break; @@ -930,7 +930,7 @@ s32 e1000e_setup_fiber_serdes_link(struct e1000_hw *hw) ew32(CTRL, ctrl); e1e_flush(); - msleep(1); + usleep_range(1000, 2000); /* * For these adapters, the SW definable pin 1 is set when the optics @@ -1181,7 +1181,7 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw) * of pause frames. In this case, we had to advertise * FULL flow control because we could not advertise Rx * ONLY. Hence, we must now check to see if we need to - * turn OFF the TRANSMISSION of PAUSE frames. + * turn OFF the TRANSMISSION of PAUSE frames. */ if (hw->fc.requested_mode == e1000_fc_full) { hw->fc.current_mode = e1000_fc_full; @@ -1385,7 +1385,7 @@ s32 e1000e_get_auto_rd_done(struct e1000_hw *hw) while (i < AUTO_READ_DONE_TIMEOUT) { if (er32(EECD) & E1000_EECD_AUTO_RD) break; - msleep(1); + usleep_range(1000, 2000); i++; } @@ -1530,12 +1530,12 @@ s32 e1000e_cleanup_led_generic(struct e1000_hw *hw) } /** - * e1000e_blink_led - Blink LED + * e1000e_blink_led_generic - Blink LED * @hw: pointer to the HW structure * * Blink the LEDs which are set to be on. **/ -s32 e1000e_blink_led(struct e1000_hw *hw) +s32 e1000e_blink_led_generic(struct e1000_hw *hw) { u32 ledctl_blink = 0; u32 i; @@ -2087,8 +2087,6 @@ s32 e1000e_write_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words, u16 *data) if (ret_val) return ret_val; - msleep(10); - while (widx < words) { u8 write_opcode = NVM_WRITE_OPCODE_SPI; @@ -2132,7 +2130,7 @@ s32 e1000e_write_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words, u16 *data) } } - msleep(10); + usleep_range(10000, 20000); nvm->ops.release(hw); return 0; } |