summaryrefslogtreecommitdiffstats
path: root/drivers/net/e1000e/netdev.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/e1000e/netdev.c')
-rw-r--r--drivers/net/e1000e/netdev.c50
1 files changed, 33 insertions, 17 deletions
diff --git a/drivers/net/e1000e/netdev.c b/drivers/net/e1000e/netdev.c
index 11a527484e1..e546b4ebf15 100644
--- a/drivers/net/e1000e/netdev.c
+++ b/drivers/net/e1000e/netdev.c
@@ -2760,25 +2760,38 @@ void e1000e_reset(struct e1000_adapter *adapter)
/*
* flow control settings
*
- * The high water mark must be low enough to fit two full frame
+ * The high water mark must be low enough to fit one full frame
* (or the size used for early receive) above it in the Rx FIFO.
* Set it to the lower of:
* - 90% of the Rx FIFO size, and
* - the full Rx FIFO size minus the early receive size (for parts
* with ERT support assuming ERT set to E1000_ERT_2048), or
- * - the full Rx FIFO size minus two full frames
+ * - the full Rx FIFO size minus one full frame
*/
- if ((adapter->flags & FLAG_HAS_ERT) &&
- (adapter->netdev->mtu > ETH_DATA_LEN))
- hwm = min(((pba << 10) * 9 / 10),
- ((pba << 10) - (E1000_ERT_2048 << 3)));
- else
- hwm = min(((pba << 10) * 9 / 10),
- ((pba << 10) - (2 * adapter->max_frame_size)));
+ if (hw->mac.type == e1000_pchlan) {
+ /*
+ * Workaround PCH LOM adapter hangs with certain network
+ * loads. If hangs persist, try disabling Tx flow control.
+ */
+ if (adapter->netdev->mtu > ETH_DATA_LEN) {
+ fc->high_water = 0x3500;
+ fc->low_water = 0x1500;
+ } else {
+ fc->high_water = 0x5000;
+ fc->low_water = 0x3000;
+ }
+ } else {
+ if ((adapter->flags & FLAG_HAS_ERT) &&
+ (adapter->netdev->mtu > ETH_DATA_LEN))
+ hwm = min(((pba << 10) * 9 / 10),
+ ((pba << 10) - (E1000_ERT_2048 << 3)));
+ else
+ hwm = min(((pba << 10) * 9 / 10),
+ ((pba << 10) - adapter->max_frame_size));
- fc->high_water = hwm & E1000_FCRTH_RTH; /* 8-byte granularity */
- fc->low_water = (fc->high_water - (2 * adapter->max_frame_size));
- fc->low_water &= E1000_FCRTL_RTL; /* 8-byte granularity */
+ fc->high_water = hwm & E1000_FCRTH_RTH; /* 8-byte granularity */
+ fc->low_water = fc->high_water - 8;
+ }
if (adapter->flags & FLAG_DISABLE_FC_PAUSE_TIME)
fc->pause_time = 0xFFFF;
@@ -2804,6 +2817,10 @@ void e1000e_reset(struct e1000_adapter *adapter)
if (mac->ops.init_hw(hw))
e_err("Hardware Error\n");
+ /* additional part of the flow-control workaround above */
+ if (hw->mac.type == e1000_pchlan)
+ ew32(FCRTV_PCH, 0x1000);
+
e1000_update_mng_vlan(adapter);
/* Enable h/w to recognize an 802.1Q VLAN Ethernet packet */
@@ -3612,7 +3629,7 @@ static void e1000_watchdog_task(struct work_struct *work)
case SPEED_100:
txb2b = 0;
netdev->tx_queue_len = 100;
- /* maybe add some timeout factor ? */
+ adapter->tx_timeout_factor = 10;
break;
}
@@ -4284,8 +4301,10 @@ static int e1000_change_mtu(struct net_device *netdev, int new_mtu)
while (test_and_set_bit(__E1000_RESETTING, &adapter->state))
msleep(1);
- /* e1000e_down has a dependency on max_frame_size */
+ /* e1000e_down -> e1000e_reset dependent on max_frame_size & mtu */
adapter->max_frame_size = max_frame;
+ e_info("changing MTU from %d to %d\n", netdev->mtu, new_mtu);
+ netdev->mtu = new_mtu;
if (netif_running(netdev))
e1000e_down(adapter);
@@ -4315,9 +4334,6 @@ static int e1000_change_mtu(struct net_device *netdev, int new_mtu)
adapter->rx_buffer_len = ETH_FRAME_LEN + VLAN_HLEN
+ ETH_FCS_LEN;
- e_info("changing MTU from %d to %d\n", netdev->mtu, new_mtu);
- netdev->mtu = new_mtu;
-
if (netif_running(netdev))
e1000e_up(adapter);
else