summaryrefslogtreecommitdiffstats
path: root/drivers/net/e1000e
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/e1000e')
-rw-r--r--drivers/net/e1000e/82571.c22
-rw-r--r--drivers/net/e1000e/defines.h10
-rw-r--r--drivers/net/e1000e/e1000.h3
-rw-r--r--drivers/net/e1000e/hw.h4
-rw-r--r--drivers/net/e1000e/ich8lan.c24
-rw-r--r--drivers/net/e1000e/lib.c50
-rw-r--r--drivers/net/e1000e/netdev.c18
-rw-r--r--drivers/net/e1000e/phy.c10
8 files changed, 53 insertions, 88 deletions
diff --git a/drivers/net/e1000e/82571.c b/drivers/net/e1000e/82571.c
index 3beace55b58..7fe20310eb5 100644
--- a/drivers/net/e1000e/82571.c
+++ b/drivers/net/e1000e/82571.c
@@ -438,7 +438,7 @@ static void e1000_release_nvm_82571(struct e1000_hw *hw)
* For non-82573 silicon, write data to EEPROM at offset using SPI interface.
*
* If e1000e_update_nvm_checksum is not called after this function, the
- * EEPROM will most likley contain an invalid checksum.
+ * EEPROM will most likely contain an invalid checksum.
**/
static s32 e1000_write_nvm_82571(struct e1000_hw *hw, u16 offset, u16 words,
u16 *data)
@@ -547,7 +547,7 @@ static s32 e1000_validate_nvm_checksum_82571(struct e1000_hw *hw)
* poll for completion.
*
* If e1000e_update_nvm_checksum is not called after this function, the
- * EEPROM will most likley contain an invalid checksum.
+ * EEPROM will most likely contain an invalid checksum.
**/
static s32 e1000_write_nvm_eewr_82571(struct e1000_hw *hw, u16 offset,
u16 words, u16 *data)
@@ -1053,7 +1053,7 @@ static s32 e1000_setup_fiber_serdes_link_82571(struct e1000_hw *hw)
/* If SerDes loopback mode is entered, there is no form
* of reset to take the adapter out of that mode. So we
* have to explicitly take the adapter out of loopback
- * mode. This prevents drivers from twidling their thumbs
+ * mode. This prevents drivers from twiddling their thumbs
* if another tool failed to take it out of loopback mode.
*/
ew32(SCTL,
@@ -1098,7 +1098,7 @@ static s32 e1000_valid_led_default_82571(struct e1000_hw *hw, u16 *data)
* e1000e_get_laa_state_82571 - Get locally administered address state
* @hw: pointer to the HW structure
*
- * Retrieve and return the current locally administed address state.
+ * Retrieve and return the current locally administered address state.
**/
bool e1000e_get_laa_state_82571(struct e1000_hw *hw)
{
@@ -1113,7 +1113,7 @@ bool e1000e_get_laa_state_82571(struct e1000_hw *hw)
* @hw: pointer to the HW structure
* @state: enable/disable locally administered address
*
- * Enable/Disable the current locally administed address state.
+ * Enable/Disable the current locally administers address state.
**/
void e1000e_set_laa_state_82571(struct e1000_hw *hw, bool state)
{
@@ -1281,16 +1281,6 @@ static struct e1000_phy_operations e82_phy_ops_m88 = {
static struct e1000_nvm_operations e82571_nvm_ops = {
.acquire_nvm = e1000_acquire_nvm_82571,
- .read_nvm = e1000e_read_nvm_spi,
- .release_nvm = e1000_release_nvm_82571,
- .update_nvm = e1000_update_nvm_checksum_82571,
- .valid_led_default = e1000_valid_led_default_82571,
- .validate_nvm = e1000_validate_nvm_checksum_82571,
- .write_nvm = e1000_write_nvm_82571,
-};
-
-static struct e1000_nvm_operations e82573_nvm_ops = {
- .acquire_nvm = e1000_acquire_nvm_82571,
.read_nvm = e1000e_read_nvm_eerd,
.release_nvm = e1000_release_nvm_82571,
.update_nvm = e1000_update_nvm_checksum_82571,
@@ -1355,6 +1345,6 @@ struct e1000_info e1000_82573_info = {
.get_invariants = e1000_get_invariants_82571,
.mac_ops = &e82571_mac_ops,
.phy_ops = &e82_phy_ops_m88,
- .nvm_ops = &e82573_nvm_ops,
+ .nvm_ops = &e82571_nvm_ops,
};
diff --git a/drivers/net/e1000e/defines.h b/drivers/net/e1000e/defines.h
index 6232c3e9668..a4f511f549f 100644
--- a/drivers/net/e1000e/defines.h
+++ b/drivers/net/e1000e/defines.h
@@ -66,7 +66,7 @@
#define E1000_WUFC_ARP 0x00000020 /* ARP Request Packet Wakeup Enable */
/* Extended Device Control */
-#define E1000_CTRL_EXT_SDP7_DATA 0x00000080 /* Value of SW Defineable Pin 7 */
+#define E1000_CTRL_EXT_SDP7_DATA 0x00000080 /* Value of SW Definable Pin 7 */
#define E1000_CTRL_EXT_EE_RST 0x00002000 /* Reinitialize from EEPROM */
#define E1000_CTRL_EXT_RO_DIS 0x00020000 /* Relaxed Ordering disable */
#define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000
@@ -75,12 +75,12 @@
#define E1000_CTRL_EXT_IAME 0x08000000 /* Interrupt acknowledge Auto-mask */
#define E1000_CTRL_EXT_INT_TIMER_CLR 0x20000000 /* Clear Interrupt timers after IMS clear */
-/* Receive Decriptor bit definitions */
+/* Receive Descriptor bit definitions */
#define E1000_RXD_STAT_DD 0x01 /* Descriptor Done */
#define E1000_RXD_STAT_EOP 0x02 /* End of Packet */
#define E1000_RXD_STAT_IXSM 0x04 /* Ignore checksum */
#define E1000_RXD_STAT_VP 0x08 /* IEEE VLAN Packet */
-#define E1000_RXD_STAT_UDPCS 0x10 /* UDP xsum caculated */
+#define E1000_RXD_STAT_UDPCS 0x10 /* UDP xsum calculated */
#define E1000_RXD_STAT_TCPCS 0x20 /* TCP xsum calculated */
#define E1000_RXD_ERR_CE 0x01 /* CRC Error */
#define E1000_RXD_ERR_SE 0x02 /* Symbol Error */
@@ -223,7 +223,7 @@
#define E1000_STATUS_LAN_INIT_DONE 0x00000200 /* Lan Init Completion by NVM */
#define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000 /* Status of Master requests. */
-/* Constants used to intrepret the masked PCI-X bus speed. */
+/* Constants used to interpret the masked PCI-X bus speed. */
#define HALF_DUPLEX 1
#define FULL_DUPLEX 2
@@ -517,7 +517,7 @@
/* PHY 1000 MII Register/Bit Definitions */
/* PHY Registers defined by IEEE */
#define PHY_CONTROL 0x00 /* Control Register */
-#define PHY_STATUS 0x01 /* Status Regiser */
+#define PHY_STATUS 0x01 /* Status Register */
#define PHY_ID1 0x02 /* Phy Id Reg (word 1) */
#define PHY_ID2 0x03 /* Phy Id Reg (word 2) */
#define PHY_AUTONEG_ADV 0x04 /* Autoneg Advertisement */
diff --git a/drivers/net/e1000e/e1000.h b/drivers/net/e1000e/e1000.h
index 8b88c226e85..327c0620da3 100644
--- a/drivers/net/e1000e/e1000.h
+++ b/drivers/net/e1000e/e1000.h
@@ -42,8 +42,7 @@
struct e1000_info;
#define ndev_printk(level, netdev, format, arg...) \
- printk(level "%s: %s: " format, (netdev)->dev.parent->bus_id, \
- (netdev)->name, ## arg)
+ printk(level "%s: " format, (netdev)->name, ## arg)
#ifdef DEBUG
#define ndev_dbg(netdev, format, arg...) \
diff --git a/drivers/net/e1000e/hw.h b/drivers/net/e1000e/hw.h
index 3c5862f97db..916025b30fc 100644
--- a/drivers/net/e1000e/hw.h
+++ b/drivers/net/e1000e/hw.h
@@ -184,7 +184,7 @@ enum e1e_registers {
E1000_ICRXDMTC = 0x04120, /* Irq Cause Rx Desc MinThreshold Count */
E1000_ICRXOC = 0x04124, /* Irq Cause Receiver Overrun Count */
E1000_RXCSUM = 0x05000, /* RX Checksum Control - RW */
- E1000_RFCTL = 0x05008, /* Receive Filter Control*/
+ E1000_RFCTL = 0x05008, /* Receive Filter Control */
E1000_MTA = 0x05200, /* Multicast Table Array - RW Array */
E1000_RA = 0x05400, /* Receive Address - RW Array */
E1000_VFTA = 0x05600, /* VLAN Filter Table Array - RW Array */
@@ -202,7 +202,7 @@ enum e1e_registers {
E1000_FACTPS = 0x05B30, /* Function Active and Power State to MNG */
E1000_SWSM = 0x05B50, /* SW Semaphore */
E1000_FWSM = 0x05B54, /* FW Semaphore */
- E1000_HICR = 0x08F00, /* Host Inteface Control */
+ E1000_HICR = 0x08F00, /* Host Interface Control */
};
/* RSS registers */
diff --git a/drivers/net/e1000e/ich8lan.c b/drivers/net/e1000e/ich8lan.c
index 8f8139de1f4..0ae39550768 100644
--- a/drivers/net/e1000e/ich8lan.c
+++ b/drivers/net/e1000e/ich8lan.c
@@ -671,7 +671,7 @@ static s32 e1000_get_phy_info_ich8lan(struct e1000_hw *hw)
* e1000_check_polarity_ife_ich8lan - Check cable polarity for IFE PHY
* @hw: pointer to the HW structure
*
- * Polarity is determined on the polarity reveral feature being enabled.
+ * Polarity is determined on the polarity reversal feature being enabled.
* This function is only called by other family-specific
* routines.
**/
@@ -947,7 +947,7 @@ static s32 e1000_flash_cycle_init_ich8lan(struct e1000_hw *hw)
/* Either we should have a hardware SPI cycle in progress
* bit to check against, in order to start a new cycle or
* FDONE bit should be changed in the hardware so that it
- * is 1 after harware reset, which can then be used as an
+ * is 1 after hardware reset, which can then be used as an
* indication whether a cycle is in progress or has been
* completed.
*/
@@ -1155,7 +1155,7 @@ static s32 e1000_write_nvm_ich8lan(struct e1000_hw *hw, u16 offset, u16 words,
* which writes the checksum to the shadow ram. The changes in the shadow
* ram are then committed to the EEPROM by processing each bank at a time
* checking for the modified bit and writing only the pending changes.
- * After a succesful commit, the shadow ram is cleared and is ready for
+ * After a successful commit, the shadow ram is cleared and is ready for
* future writes.
**/
static s32 e1000_update_nvm_checksum_ich8lan(struct e1000_hw *hw)
@@ -1680,7 +1680,7 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw)
* - initialize LED identification
* - setup receive address registers
* - setup flow control
- * - setup transmit discriptors
+ * - setup transmit descriptors
* - clear statistics
**/
static s32 e1000_init_hw_ich8lan(struct e1000_hw *hw)
@@ -1961,7 +1961,7 @@ static s32 e1000_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw)
E1000_PHY_CTRL_NOND0A_GBE_DISABLE);
ew32(PHY_CTRL, phy_ctrl);
- /* Call gig speed drop workaround on Giga disable before accessing
+ /* Call gig speed drop workaround on Gig disable before accessing
* any PHY registers */
e1000e_gig_downshift_workaround_ich8lan(hw);
@@ -1972,7 +1972,7 @@ static s32 e1000_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw)
/**
* e1000_set_kmrn_lock_loss_workaound_ich8lan - Set Kumeran workaround state
* @hw: pointer to the HW structure
- * @state: boolean value used to set the current Kumaran workaround state
+ * @state: boolean value used to set the current Kumeran workaround state
*
* If ICH8, set the current Kumeran workaround state (enabled - TRUE
* /disabled - FALSE).
@@ -2017,7 +2017,7 @@ void e1000e_igp3_phy_powerdown_workaround_ich8lan(struct e1000_hw *hw)
E1000_PHY_CTRL_NOND0A_GBE_DISABLE);
ew32(PHY_CTRL, reg);
- /* Call gig speed drop workaround on Giga disable before
+ /* Call gig speed drop workaround on Gig disable before
* accessing any PHY registers */
if (hw->mac.type == e1000_ich8lan)
e1000e_gig_downshift_workaround_ich8lan(hw);
@@ -2045,7 +2045,7 @@ void e1000e_igp3_phy_powerdown_workaround_ich8lan(struct e1000_hw *hw)
* @hw: pointer to the HW structure
*
* Steps to take when dropping from 1Gb/s (eg. link cable removal (LSC),
- * LPLU, Giga disable, MDIC PHY reset):
+ * LPLU, Gig disable, MDIC PHY reset):
* 1) Set Kumeran Near-end loopback
* 2) Clear Kumeran Near-end loopback
* Should only be called for ICH8[m] devices with IGP_3 Phy.
@@ -2089,10 +2089,10 @@ static s32 e1000_cleanup_led_ich8lan(struct e1000_hw *hw)
}
/**
- * e1000_led_on_ich8lan - Turn LED's on
+ * e1000_led_on_ich8lan - Turn LEDs on
* @hw: pointer to the HW structure
*
- * Turn on the LED's.
+ * Turn on the LEDs.
**/
static s32 e1000_led_on_ich8lan(struct e1000_hw *hw)
{
@@ -2105,10 +2105,10 @@ static s32 e1000_led_on_ich8lan(struct e1000_hw *hw)
}
/**
- * e1000_led_off_ich8lan - Turn LED's off
+ * e1000_led_off_ich8lan - Turn LEDs off
* @hw: pointer to the HW structure
*
- * Turn off the LED's.
+ * Turn off the LEDs.
**/
static s32 e1000_led_off_ich8lan(struct e1000_hw *hw)
{
diff --git a/drivers/net/e1000e/lib.c b/drivers/net/e1000e/lib.c
index 16f35fadb74..95f75a43c9f 100644
--- a/drivers/net/e1000e/lib.c
+++ b/drivers/net/e1000e/lib.c
@@ -589,9 +589,6 @@ static s32 e1000_set_default_fc_generic(struct e1000_hw *hw)
s32 ret_val;
u16 nvm_data;
- if (mac->fc != e1000_fc_default)
- return 0;
-
/* Read and store word 0x0F of the EEPROM. This word contains bits
* that determine the hardware's default PAUSE (flow control) mode,
* a bit that determines whether the HW defaults to enabling or
@@ -1107,34 +1104,13 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
(mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
mac->fc = e1000_fc_rx_pause;
hw_dbg(hw, "Flow Control = RX PAUSE frames only.\r\n");
- }
- /* Per the IEEE spec, at this point flow control should be
- * disabled. However, we want to consider that we could
- * be connected to a legacy switch that doesn't advertise
- * desired flow control, but can be forced on the link
- * partner. So if we advertised no flow control, that is
- * what we will resolve to. If we advertised some kind of
- * receive capability (Rx Pause Only or Full Flow Control)
- * and the link partner advertised none, we will configure
- * ourselves to enable Rx Flow Control only. We can do
- * this safely for two reasons: If the link partner really
- * didn't want flow control enabled, and we enable Rx, no
- * harm done since we won't be receiving any PAUSE frames
- * anyway. If the intent on the link partner was to have
- * flow control enabled, then by us enabling RX only, we
- * can at least receive pause frames and process them.
- * This is a good idea because in most cases, since we are
- * predominantly a server NIC, more times than not we will
- * be asked to delay transmission of packets than asking
- * our link partner to pause transmission of frames.
- */
- else if ((mac->original_fc == e1000_fc_none) ||
- (mac->original_fc == e1000_fc_tx_pause)) {
+ } else {
+ /*
+ * Per the IEEE spec, at this point flow control
+ * should be disabled.
+ */
mac->fc = e1000_fc_none;
hw_dbg(hw, "Flow Control = NONE.\r\n");
- } else {
- mac->fc = e1000_fc_rx_pause;
- hw_dbg(hw, "Flow Control = RX PAUSE frames only.\r\n");
}
/* Now we need to do one last check... If we auto-
@@ -1164,7 +1140,7 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw)
}
/**
- * e1000e_get_speed_and_duplex_copper - Retreive current speed/duplex
+ * e1000e_get_speed_and_duplex_copper - Retrieve current speed/duplex
* @hw: pointer to the HW structure
* @speed: stores the current speed
* @duplex: stores the current duplex
@@ -1200,7 +1176,7 @@ s32 e1000e_get_speed_and_duplex_copper(struct e1000_hw *hw, u16 *speed, u16 *dup
}
/**
- * e1000e_get_speed_and_duplex_fiber_serdes - Retreive current speed/duplex
+ * e1000e_get_speed_and_duplex_fiber_serdes - Retrieve current speed/duplex
* @hw: pointer to the HW structure
* @speed: stores the current speed
* @duplex: stores the current duplex
@@ -1410,7 +1386,7 @@ s32 e1000e_cleanup_led_generic(struct e1000_hw *hw)
* e1000e_blink_led - Blink LED
* @hw: pointer to the HW structure
*
- * Blink the led's which are set to be on.
+ * Blink the LEDs which are set to be on.
**/
s32 e1000e_blink_led(struct e1000_hw *hw)
{
@@ -1515,7 +1491,7 @@ void e1000e_set_pcie_no_snoop(struct e1000_hw *hw, u32 no_snoop)
* @hw: pointer to the HW structure
*
* Returns 0 if successful, else returns -10
- * (-E1000_ERR_MASTER_REQUESTS_PENDING) if master disable bit has not casued
+ * (-E1000_ERR_MASTER_REQUESTS_PENDING) if master disable bit has not caused
* the master requests to be disabled.
*
* Disables PCI-Express master access and verifies there are no pending
@@ -1876,7 +1852,7 @@ static s32 e1000_ready_nvm_eeprom(struct e1000_hw *hw)
}
/**
- * e1000e_read_nvm_spi - Read EEPROM's using SPI
+ * e1000e_read_nvm_spi - Reads EEPROM using SPI
* @hw: pointer to the HW structure
* @offset: offset of word in the EEPROM to read
* @words: number of words to read
@@ -1980,7 +1956,7 @@ s32 e1000e_read_nvm_eerd(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
* Writes data to EEPROM at offset using SPI interface.
*
* If e1000e_update_nvm_checksum is not called after this function , the
- * EEPROM will most likley contain an invalid checksum.
+ * EEPROM will most likely contain an invalid checksum.
**/
s32 e1000e_write_nvm_spi(struct e1000_hw *hw, u16 offset, u16 words, u16 *data)
{
@@ -2222,7 +2198,7 @@ static u8 e1000_calculate_checksum(u8 *buffer, u32 length)
*
* Returns E1000_success upon success, else E1000_ERR_HOST_INTERFACE_COMMAND
*
- * This function checks whether the HOST IF is enabled for command operaton
+ * This function checks whether the HOST IF is enabled for command operation
* and also checks whether the previous command is completed. It busy waits
* in case of previous command is not completed.
**/
@@ -2254,7 +2230,7 @@ static s32 e1000_mng_enable_host_if(struct e1000_hw *hw)
}
/**
- * e1000e_check_mng_mode - check managament mode
+ * e1000e_check_mng_mode - check management mode
* @hw: pointer to the HW structure
*
* Reads the firmware semaphore register and returns true (>0) if
diff --git a/drivers/net/e1000e/netdev.c b/drivers/net/e1000e/netdev.c
index 3031d6d1624..fc5c63f4f57 100644
--- a/drivers/net/e1000e/netdev.c
+++ b/drivers/net/e1000e/netdev.c
@@ -1006,7 +1006,7 @@ static void e1000_irq_enable(struct e1000_adapter *adapter)
* e1000_get_hw_control - get control of the h/w from f/w
* @adapter: address of board private structure
*
- * e1000_get_hw_control sets {CTRL_EXT|FWSM}:DRV_LOAD bit.
+ * e1000_get_hw_control sets {CTRL_EXT|SWSM}:DRV_LOAD bit.
* For ASF and Pass Through versions of f/w this means that
* the driver is loaded. For AMT version (only with 82573)
* of the f/w this means that the network i/f is open.
@@ -1032,7 +1032,7 @@ static void e1000_get_hw_control(struct e1000_adapter *adapter)
* e1000_release_hw_control - release control of the h/w to f/w
* @adapter: address of board private structure
*
- * e1000_release_hw_control resets {CTRL_EXT|FWSM}:DRV_LOAD bit.
+ * e1000_release_hw_control resets {CTRL_EXT|SWSM}:DRV_LOAD bit.
* For ASF and Pass Through versions of f/w this means that the
* driver is no longer loaded. For AMT version (only with 82573) i
* of the f/w this means that the network i/f is closed.
@@ -1241,6 +1241,11 @@ void e1000e_free_rx_resources(struct e1000_adapter *adapter)
/**
* e1000_update_itr - update the dynamic ITR value based on statistics
+ * @adapter: pointer to adapter
+ * @itr_setting: current adapter->itr
+ * @packets: the number of packets during this measurement interval
+ * @bytes: the number of bytes during this measurement interval
+ *
* Stores a new ITR value based on packets and byte
* counts during the last interrupt. The advantage of per interrupt
* computation is faster updates and more accurate ITR for the current
@@ -1250,10 +1255,6 @@ void e1000e_free_rx_resources(struct e1000_adapter *adapter)
* while increasing bulk throughput.
* this functionality is controlled by the InterruptThrottleRate module
* parameter (see e1000_param.c)
- * @adapter: pointer to adapter
- * @itr_setting: current adapter->itr
- * @packets: the number of packets during this measurement interval
- * @bytes: the number of bytes during this measurement interval
**/
static unsigned int e1000_update_itr(struct e1000_adapter *adapter,
u16 itr_setting, int packets,
@@ -1366,6 +1367,7 @@ set_itr_now:
/**
* e1000_clean - NAPI Rx polling callback
* @adapter: board private structure
+ * @budget: amount of packets driver is allowed to process this poll
**/
static int e1000_clean(struct napi_struct *napi, int budget)
{
@@ -2000,7 +2002,7 @@ static void e1000_power_down_phy(struct e1000_adapter *adapter)
e1000_check_reset_block(hw))
return;
- /* managebility (AMT) is enabled */
+ /* manageability (AMT) is enabled */
if (er32(MANC) & E1000_MANC_SMBUS_EN)
return;
@@ -3488,7 +3490,6 @@ static int e1000_suspend(struct pci_dev *pdev, pm_message_t state)
static void e1000e_disable_l1aspm(struct pci_dev *pdev)
{
int pos;
- u32 cap;
u16 val;
/*
@@ -3503,7 +3504,6 @@ static void e1000e_disable_l1aspm(struct pci_dev *pdev)
* active.
*/
pos = pci_find_capability(pdev, PCI_CAP_ID_EXP);
- pci_read_config_dword(pdev, pos + PCI_EXP_LNKCAP, &cap);
pci_read_config_word(pdev, pos + PCI_EXP_LNKCTL, &val);
if (val & 0x2) {
dev_warn(&pdev->dev, "Disabling L1 ASPM\n");
diff --git a/drivers/net/e1000e/phy.c b/drivers/net/e1000e/phy.c
index fc6fee112f1..dab3c468a76 100644
--- a/drivers/net/e1000e/phy.c
+++ b/drivers/net/e1000e/phy.c
@@ -121,7 +121,7 @@ s32 e1000e_phy_reset_dsp(struct e1000_hw *hw)
* @offset: register offset to be read
* @data: pointer to the read data
*
- * Reads the MDI control regsiter in the PHY at offset and stores the
+ * Reads the MDI control register in the PHY at offset and stores the
* information read to data.
**/
static s32 e1000_read_phy_reg_mdic(struct e1000_hw *hw, u32 offset, u16 *data)
@@ -1172,7 +1172,7 @@ s32 e1000e_set_d3_lplu_state(struct e1000_hw *hw, bool active)
}
/**
- * e1000e_check_downshift - Checks whether a downshift in speed occured
+ * e1000e_check_downshift - Checks whether a downshift in speed occurred
* @hw: pointer to the HW structure
*
* Success returns 0, Failure returns 1
@@ -1388,8 +1388,8 @@ s32 e1000e_get_cable_length_m88(struct e1000_hw *hw)
*
* The automatic gain control (agc) normalizes the amplitude of the
* received signal, adjusting for the attenuation produced by the
- * cable. By reading the AGC registers, which reperesent the
- * cobination of course and fine gain value, the value can be put
+ * cable. By reading the AGC registers, which represent the
+ * combination of course and fine gain value, the value can be put
* into a lookup table to obtain the approximate cable length
* for each channel.
**/
@@ -1619,7 +1619,7 @@ s32 e1000e_phy_sw_reset(struct e1000_hw *hw)
* Verify the reset block is not blocking us from resetting. Acquire
* semaphore (if necessary) and read/set/write the device control reset
* bit in the PHY. Wait the appropriate delay time for the device to
- * reset and relase the semaphore (if necessary).
+ * reset and release the semaphore (if necessary).
**/
s32 e1000e_phy_hw_reset_generic(struct e1000_hw *hw)
{
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-12-30 16:53:57 +0000