5 files changed, 408 insertions, 106 deletions

diff --git a/drivers/net/e1000e/defines.h b/drivers/net/e1000e/defines.h
index c0f185beb8b..1190167a8b3 100644
--- a/drivers/net/e1000e/defines.h
+++ b/drivers/net/e1000e/defines.h
@@ -76,6 +76,7 @@
 /* Extended Device Control */
 #define E1000_CTRL_EXT_SDP7_DATA 0x00000080 /* Value of SW Definable Pin 7 */
 #define E1000_CTRL_EXT_EE_RST    0x00002000 /* Reinitialize from EEPROM */
+#define E1000_CTRL_EXT_SPD_BYPS  0x00008000 /* Speed Select Bypass */
 #define E1000_CTRL_EXT_RO_DIS    0x00020000 /* Relaxed Ordering disable */
 #define E1000_CTRL_EXT_DMA_DYN_CLK_EN 0x00080000 /* DMA Dynamic Clock Gating */
 #define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000
@@ -347,6 +348,7 @@
 /* Extended Configuration Control and Size */
 #define E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP      0x00000020
 #define E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE       0x00000001
+#define E1000_EXTCNF_CTRL_OEM_WRITE_ENABLE       0x00000008
 #define E1000_EXTCNF_CTRL_SWFLAG                 0x00000020
 #define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK   0x00FF0000
 #define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT          16
diff --git a/drivers/net/e1000e/e1000.h b/drivers/net/e1000e/e1000.h
index 405a144ebca..189dfa2d6c7 100644
--- a/drivers/net/e1000e/e1000.h
+++ b/drivers/net/e1000e/e1000.h
@@ -141,6 +141,20 @@ struct e1000_info;
 #define HV_TNCRS_UPPER		PHY_REG(778, 29) /* Transmit with no CRS */
 #define HV_TNCRS_LOWER		PHY_REG(778, 30)
 
+/* BM PHY Copper Specific Status */
+#define BM_CS_STATUS                      17
+#define BM_CS_STATUS_LINK_UP              0x0400
+#define BM_CS_STATUS_RESOLVED             0x0800
+#define BM_CS_STATUS_SPEED_MASK           0xC000
+#define BM_CS_STATUS_SPEED_1000           0x8000
+
+/* 82577 Mobile Phy Status Register */
+#define HV_M_STATUS                       26
+#define HV_M_STATUS_AUTONEG_COMPLETE      0x1000
+#define HV_M_STATUS_SPEED_MASK            0x0300
+#define HV_M_STATUS_SPEED_1000            0x0200
+#define HV_M_STATUS_LINK_UP               0x0040
+
 enum e1000_boards {
 	board_82571,
 	board_82572,
diff --git a/drivers/net/e1000e/hw.h b/drivers/net/e1000e/hw.h
index 7b05cf47f7f..aaea41ef794 100644
--- a/drivers/net/e1000e/hw.h
+++ b/drivers/net/e1000e/hw.h
@@ -903,6 +903,7 @@ struct e1000_shadow_ram {
 struct e1000_dev_spec_ich8lan {
 	bool kmrn_lock_loss_workaround_enabled;
 	struct e1000_shadow_ram shadow_ram[E1000_ICH8_SHADOW_RAM_WORDS];
+	bool nvm_k1_enabled;
 };
 
 struct e1000_hw {
diff --git a/drivers/net/e1000e/ich8lan.c b/drivers/net/e1000e/ich8lan.c
index b6388b9535f..51ddb04ab19 100644
--- a/drivers/net/e1000e/ich8lan.c
+++ b/drivers/net/e1000e/ich8lan.c
@@ -124,11 +124,25 @@
 
 #define SW_FLAG_TIMEOUT    1000 /* SW Semaphore flag timeout in milliseconds */
 
+/* SMBus Address Phy Register */
+#define HV_SMB_ADDR            PHY_REG(768, 26)
+#define HV_SMB_ADDR_PEC_EN     0x0200
+#define HV_SMB_ADDR_VALID      0x0080
+
+/* Strapping Option Register - RO */
+#define E1000_STRAP                     0x0000C
+#define E1000_STRAP_SMBUS_ADDRESS_MASK  0x00FE0000
+#define E1000_STRAP_SMBUS_ADDRESS_SHIFT 17
+
 /* OEM Bits Phy Register */
 #define HV_OEM_BITS            PHY_REG(768, 25)
 #define HV_OEM_BITS_LPLU       0x0004 /* Low Power Link Up */
+#define HV_OEM_BITS_GBE_DIS    0x0040 /* Gigabit Disable */
 #define HV_OEM_BITS_RESTART_AN 0x0400 /* Restart Auto-negotiation */
 
+#define E1000_NVM_K1_CONFIG 0x1B /* NVM K1 Config Word */
+#define E1000_NVM_K1_ENABLE 0x1  /* NVM Enable K1 bit */
+
 /* ICH GbE Flash Hardware Sequencing Flash Status Register bit breakdown */
 /* Offset 04h HSFSTS */
 union ich8_hws_flash_status {
@@ -208,6 +222,9 @@ static s32 e1000_cleanup_led_pchlan(struct e1000_hw *hw);
 static s32 e1000_led_on_pchlan(struct e1000_hw *hw);
 static s32 e1000_led_off_pchlan(struct e1000_hw *hw);
 static s32 e1000_set_lplu_state_pchlan(struct e1000_hw *hw, bool active);
+static void e1000_lan_init_done_ich8lan(struct e1000_hw *hw);
+static s32  e1000_k1_gig_workaround_hv(struct e1000_hw *hw, bool link);
+static s32 e1000_configure_k1_ich8lan(struct e1000_hw *hw, bool k1_enable);
 
 static inline u16 __er16flash(struct e1000_hw *hw, unsigned long reg)
 {
@@ -483,14 +500,6 @@ static s32 e1000_check_for_copper_link_ich8lan(struct e1000_hw *hw)
 		goto out;
 	}
 
-	if (hw->mac.type == e1000_pchlan) {
-		ret_val = e1000e_write_kmrn_reg(hw,
-		                                   E1000_KMRNCTRLSTA_K1_CONFIG,
-		                                   E1000_KMRNCTRLSTA_K1_ENABLE);
-		if (ret_val)
-			goto out;
-	}
-
 	/*
 	 * First we want to see if the MII Status Register reports
 	 * link.  If so, then we want to get the current speed/duplex
@@ -500,6 +509,12 @@ static s32 e1000_check_for_copper_link_ich8lan(struct e1000_hw *hw)
 	if (ret_val)
 		goto out;
 
+	if (hw->mac.type == e1000_pchlan) {
+		ret_val = e1000_k1_gig_workaround_hv(hw, link);
+		if (ret_val)
+			goto out;
+	}
+
 	if (!link)
 		goto out; /* No link detected */
 
@@ -794,6 +809,326 @@ static s32 e1000_phy_force_speed_duplex_ich8lan(struct e1000_hw *hw)
 }
 
 /**
+ *  e1000_sw_lcd_config_ich8lan - SW-based LCD Configuration
+ *  @hw:   pointer to the HW structure
+ *
+ *  SW should configure the LCD from the NVM extended configuration region
+ *  as a workaround for certain parts.
+ **/
+static s32 e1000_sw_lcd_config_ich8lan(struct e1000_hw *hw)
+{
+	struct e1000_phy_info *phy = &hw->phy;
+	u32 i, data, cnf_size, cnf_base_addr, sw_cfg_mask;
+	s32 ret_val;
+	u16 word_addr, reg_data, reg_addr, phy_page = 0;
+
+	ret_val = hw->phy.ops.acquire_phy(hw);
+	if (ret_val)
+		return ret_val;
+
+	/*
+	 * Initialize the PHY from the NVM on ICH platforms.  This
+	 * is needed due to an issue where the NVM configuration is
+	 * not properly autoloaded after power transitions.
+	 * Therefore, after each PHY reset, we will load the
+	 * configuration data out of the NVM manually.
+	 */
+	if ((hw->mac.type == e1000_ich8lan && phy->type == e1000_phy_igp_3) ||
+		(hw->mac.type == e1000_pchlan)) {
+		struct e1000_adapter *adapter = hw->adapter;
+
+		/* Check if SW needs to configure the PHY */
+		if ((adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M_AMT) ||
+		    (adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M) ||
+		    (hw->mac.type == e1000_pchlan))
+			sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG_ICH8M;
+		else
+			sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG;
+
+		data = er32(FEXTNVM);
+		if (!(data & sw_cfg_mask))
+			goto out;
+
+		/* Wait for basic configuration completes before proceeding */
+		e1000_lan_init_done_ich8lan(hw);
+
+		/*
+		 * Make sure HW does not configure LCD from PHY
+		 * extended configuration before SW configuration
+		 */
+		data = er32(EXTCNF_CTRL);
+		if (data & E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE)
+			goto out;
+
+		cnf_size = er32(EXTCNF_SIZE);
+		cnf_size &= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK;
+		cnf_size >>= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT;
+		if (!cnf_size)
+			goto out;
+
+		cnf_base_addr = data & E1000_EXTCNF_CTRL_EXT_CNF_POINTER_MASK;
+		cnf_base_addr >>= E1000_EXTCNF_CTRL_EXT_CNF_POINTER_SHIFT;
+
+		if (!(data & E1000_EXTCNF_CTRL_OEM_WRITE_ENABLE) &&
+		    (hw->mac.type == e1000_pchlan)) {
+			/*
+			 * HW configures the SMBus address and LEDs when the
+			 * OEM and LCD Write Enable bits are set in the NVM.
+			 * When both NVM bits are cleared, SW will configure
+			 * them instead.
+			 */
+			data = er32(STRAP);
+			data &= E1000_STRAP_SMBUS_ADDRESS_MASK;
+			reg_data = data >> E1000_STRAP_SMBUS_ADDRESS_SHIFT;
+			reg_data |= HV_SMB_ADDR_PEC_EN | HV_SMB_ADDR_VALID;
+			ret_val = e1000_write_phy_reg_hv_locked(hw, HV_SMB_ADDR,
+			                                        reg_data);
+			if (ret_val)
+				goto out;
+
+			data = er32(LEDCTL);
+			ret_val = e1000_write_phy_reg_hv_locked(hw,
+			                                        HV_LED_CONFIG,
+			                                        (u16)data);
+			if (ret_val)
+				goto out;
+		}
+		/* Configure LCD from extended configuration region. */
+
+		/* cnf_base_addr is in DWORD */
+		word_addr = (u16)(cnf_base_addr << 1);
+
+		for (i = 0; i < cnf_size; i++) {
+			ret_val = e1000_read_nvm(hw, (word_addr + i * 2), 1,
+			                           &reg_data);
+			if (ret_val)
+				goto out;
+
+			ret_val = e1000_read_nvm(hw, (word_addr + i * 2 + 1),
+			                           1, &reg_addr);
+			if (ret_val)
+				goto out;
+
+			/* Save off the PHY page for future writes. */
+			if (reg_addr == IGP01E1000_PHY_PAGE_SELECT) {
+				phy_page = reg_data;
+				continue;
+			}
+
+			reg_addr &= PHY_REG_MASK;
+			reg_addr |= phy_page;
+
+			ret_val = phy->ops.write_phy_reg_locked(hw,
+			                                    (u32)reg_addr,
+			                                    reg_data);
+			if (ret_val)
+				goto out;
+		}
+	}
+
+out:
+	hw->phy.ops.release_phy(hw);
+	return ret_val;
+}
+
+/**
+ *  e1000_k1_gig_workaround_hv - K1 Si workaround
+ *  @hw:   pointer to the HW structure
+ *  @link: link up bool flag
+ *
+ *  If K1 is enabled for 1Gbps, the MAC might stall when transitioning
+ *  from a lower speed.  This workaround disables K1 whenever link is at 1Gig
+ *  If link is down, the function will restore the default K1 setting located
+ *  in the NVM.
+ **/
+static s32 e1000_k1_gig_workaround_hv(struct e1000_hw *hw, bool link)
+{
+	s32 ret_val = 0;
+	u16 status_reg = 0;
+	bool k1_enable = hw->dev_spec.ich8lan.nvm_k1_enabled;
+
+	if (hw->mac.type != e1000_pchlan)
+		goto out;
+
+	/* Wrap the whole flow with the sw flag */
+	ret_val = hw->phy.ops.acquire_phy(hw);
+	if (ret_val)
+		goto out;
+
+	/* Disable K1 when link is 1Gbps, otherwise use the NVM setting */
+	if (link) {
+		if (hw->phy.type == e1000_phy_82578) {
+			ret_val = hw->phy.ops.read_phy_reg_locked(hw,
+			                                          BM_CS_STATUS,
+			                                          &status_reg);
+			if (ret_val)
+				goto release;
+
+			status_reg &= BM_CS_STATUS_LINK_UP |
+			              BM_CS_STATUS_RESOLVED |
+			              BM_CS_STATUS_SPEED_MASK;
+
+			if (status_reg == (BM_CS_STATUS_LINK_UP |
+			                   BM_CS_STATUS_RESOLVED |
+			                   BM_CS_STATUS_SPEED_1000))
+				k1_enable = false;
+		}
+
+		if (hw->phy.type == e1000_phy_82577) {
+			ret_val = hw->phy.ops.read_phy_reg_locked(hw,
+			                                          HV_M_STATUS,
+			                                          &status_reg);
+			if (ret_val)
+				goto release;
+
+			status_reg &= HV_M_STATUS_LINK_UP |
+			              HV_M_STATUS_AUTONEG_COMPLETE |
+			              HV_M_STATUS_SPEED_MASK;
+
+			if (status_reg == (HV_M_STATUS_LINK_UP |
+			                   HV_M_STATUS_AUTONEG_COMPLETE |
+			                   HV_M_STATUS_SPEED_1000))
+				k1_enable = false;
+		}
+
+		/* Link stall fix for link up */
+		ret_val = hw->phy.ops.write_phy_reg_locked(hw, PHY_REG(770, 19),
+		                                           0x0100);
+		if (ret_val)
+			goto release;
+
+	} else {
+		/* Link stall fix for link down */
+		ret_val = hw->phy.ops.write_phy_reg_locked(hw, PHY_REG(770, 19),
+		                                           0x4100);
+		if (ret_val)
+			goto release;
+	}
+
+	ret_val = e1000_configure_k1_ich8lan(hw, k1_enable);
+
+release:
+	hw->phy.ops.release_phy(hw);
+out:
+	return ret_val;
+}
+
+/**
+ *  e1000_configure_k1_ich8lan - Configure K1 power state
+ *  @hw: pointer to the HW structure
+ *  @enable: K1 state to configure
+ *
+ *  Configure the K1 power state based on the provided parameter.
+ *  Assumes semaphore already acquired.
+ *
+ *  Success returns 0, Failure returns -E1000_ERR_PHY (-2)
+ **/
+static s32 e1000_configure_k1_ich8lan(struct e1000_hw *hw, bool k1_enable)
+{
+	s32 ret_val = 0;
+	u32 ctrl_reg = 0;
+	u32 ctrl_ext = 0;
+	u32 reg = 0;
+	u16 kmrn_reg = 0;
+
+	ret_val = e1000e_read_kmrn_reg_locked(hw,
+	                                     E1000_KMRNCTRLSTA_K1_CONFIG,
+	                                     &kmrn_reg);
+	if (ret_val)
+		goto out;
+
+	if (k1_enable)
+		kmrn_reg |= E1000_KMRNCTRLSTA_K1_ENABLE;
+	else
+		kmrn_reg &= ~E1000_KMRNCTRLSTA_K1_ENABLE;
+
+	ret_val = e1000e_write_kmrn_reg_locked(hw,
+	                                      E1000_KMRNCTRLSTA_K1_CONFIG,
+	                                      kmrn_reg);
+	if (ret_val)
+		goto out;
+
+	udelay(20);
+	ctrl_ext = er32(CTRL_EXT);
+	ctrl_reg = er32(CTRL);
+
+	reg = ctrl_reg & ~(E1000_CTRL_SPD_1000 | E1000_CTRL_SPD_100);
+	reg |= E1000_CTRL_FRCSPD;
+	ew32(CTRL, reg);
+
+	ew32(CTRL_EXT, ctrl_ext | E1000_CTRL_EXT_SPD_BYPS);
+	udelay(20);
+	ew32(CTRL, ctrl_reg);
+	ew32(CTRL_EXT, ctrl_ext);
+	udelay(20);
+
+out:
+	return ret_val;
+}
+
+/**
+ *  e1000_oem_bits_config_ich8lan - SW-based LCD Configuration
+ *  @hw:       pointer to the HW structure
+ *  @d0_state: boolean if entering d0 or d3 device state
+ *
+ *  SW will configure Gbe Disable and LPLU based on the NVM. The four bits are
+ *  collectively called OEM bits.  The OEM Write Enable bit and SW Config bit
+ *  in NVM determines whether HW should configure LPLU and Gbe Disable.
+ **/
+static s32 e1000_oem_bits_config_ich8lan(struct e1000_hw *hw, bool d0_state)
+{
+	s32 ret_val = 0;
+	u32 mac_reg;
+	u16 oem_reg;
+
+	if (hw->mac.type != e1000_pchlan)
+		return ret_val;
+
+	ret_val = hw->phy.ops.acquire_phy(hw);
+	if (ret_val)
+		return ret_val;
+
+	mac_reg = er32(EXTCNF_CTRL);
+	if (mac_reg & E1000_EXTCNF_CTRL_OEM_WRITE_ENABLE)
+		goto out;
+
+	mac_reg = er32(FEXTNVM);
+	if (!(mac_reg & E1000_FEXTNVM_SW_CONFIG_ICH8M))
+		goto out;
+
+	mac_reg = er32(PHY_CTRL);
+
+	ret_val = hw->phy.ops.read_phy_reg_locked(hw, HV_OEM_BITS, &oem_reg);
+	if (ret_val)
+		goto out;
+
+	oem_reg &= ~(HV_OEM_BITS_GBE_DIS | HV_OEM_BITS_LPLU);
+
+	if (d0_state) {
+		if (mac_reg & E1000_PHY_CTRL_GBE_DISABLE)
+			oem_reg |= HV_OEM_BITS_GBE_DIS;
+
+		if (mac_reg & E1000_PHY_CTRL_D0A_LPLU)
+			oem_reg |= HV_OEM_BITS_LPLU;
+	} else {
+		if (mac_reg & E1000_PHY_CTRL_NOND0A_GBE_DISABLE)
+			oem_reg |= HV_OEM_BITS_GBE_DIS;
+
+		if (mac_reg & E1000_PHY_CTRL_NOND0A_LPLU)
+			oem_reg |= HV_OEM_BITS_LPLU;
+	}
+	/* Restart auto-neg to activate the bits */
+	oem_reg |= HV_OEM_BITS_RESTART_AN;
+	ret_val = hw->phy.ops.write_phy_reg_locked(hw, HV_OEM_BITS, oem_reg);
+
+out:
+	hw->phy.ops.release_phy(hw);
+
+	return ret_val;
+}
+
+
+/**
  *  e1000_hv_phy_workarounds_ich8lan - A series of Phy workarounds to be
  *  done after every PHY reset.
  **/
@@ -833,10 +1168,20 @@ static s32 e1000_hv_phy_workarounds_ich8lan(struct e1000_hw *hw)
 	ret_val = hw->phy.ops.acquire_phy(hw);
 	if (ret_val)
 		return ret_val;
+
 	hw->phy.addr = 1;
-	e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT, 0);
+	ret_val = e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT, 0);
+	if (ret_val)
+		goto out;
 	hw->phy.ops.release_phy(hw);
 
+	/*
+	 * Configure the K1 Si workaround during phy reset assuming there is
+	 * link so that it disables K1 if link is in 1Gbps.
+	 */
+	ret_val = e1000_k1_gig_workaround_hv(hw, true);
+
+out:
 	return ret_val;
 }
 
@@ -882,11 +1227,8 @@ static void e1000_lan_init_done_ich8lan(struct e1000_hw *hw)
  **/
 static s32 e1000_phy_hw_reset_ich8lan(struct e1000_hw *hw)
 {
-	struct e1000_phy_info *phy = &hw->phy;
-	u32 i;
-	u32 data, cnf_size, cnf_base_addr, sw_cfg_mask;
-	s32 ret_val;
-	u16 reg, word_addr, reg_data, reg_addr, phy_page = 0;
+	s32 ret_val = 0;
+	u16 reg;
 
 	ret_val = e1000e_phy_hw_reset_generic(hw);
 	if (ret_val)
@@ -905,81 +1247,16 @@ static s32 e1000_phy_hw_reset_ich8lan(struct e1000_hw *hw)
 	if (hw->mac.type == e1000_pchlan)
 		e1e_rphy(hw, BM_WUC, &reg);
 
-	/*
-	 * Initialize the PHY from the NVM on ICH platforms.  This
-	 * is needed due to an issue where the NVM configuration is
-	 * not properly autoloaded after power transitions.
-	 * Therefore, after each PHY reset, we will load the
-	 * configuration data out of the NVM manually.
-	 */
-	if (hw->mac.type == e1000_ich8lan && phy->type == e1000_phy_igp_3) {
-		struct e1000_adapter *adapter = hw->adapter;
-
-		/* Check if SW needs configure the PHY */
-		if ((adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M_AMT) ||
-		    (adapter->pdev->device == E1000_DEV_ID_ICH8_IGP_M))
-			sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG_ICH8M;
-		else
-			sw_cfg_mask = E1000_FEXTNVM_SW_CONFIG;
-
-		data = er32(FEXTNVM);
-		if (!(data & sw_cfg_mask))
-			return 0;
-
-		/* Wait for basic configuration completes before proceeding */
-		e1000_lan_init_done_ich8lan(hw);
-
-		/*
-		 * Make sure HW does not configure LCD from PHY
-		 * extended configuration before SW configuration
-		 */
-		data = er32(EXTCNF_CTRL);
-		if (data & E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE)
-			return 0;
-
-		cnf_size = er32(EXTCNF_SIZE);
-		cnf_size &= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK;
-		cnf_size >>= E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT;
-		if (!cnf_size)
-			return 0;
-
-		cnf_base_addr = data & E1000_EXTCNF_CTRL_EXT_CNF_POINTER_MASK;
-		cnf_base_addr >>= E1000_EXTCNF_CTRL_EXT_CNF_POINTER_SHIFT;
-
-		/* Configure LCD from extended configuration region. */
-
-		/* cnf_base_addr is in DWORD */
-		word_addr = (u16)(cnf_base_addr << 1);
-
-		for (i = 0; i < cnf_size; i++) {
-			ret_val = e1000_read_nvm(hw,
-						(word_addr + i * 2),
-						1,
-						&reg_data);
-			if (ret_val)
-				return ret_val;
-
-			ret_val = e1000_read_nvm(hw,
-						(word_addr + i * 2 + 1),
-						1,
-						&reg_addr);
-			if (ret_val)
-				return ret_val;
-
-			/* Save off the PHY page for future writes. */
-			if (reg_addr == IGP01E1000_PHY_PAGE_SELECT) {
-				phy_page = reg_data;
-				continue;
-			}
-
-			reg_addr |= phy_page;
+	/* Configure the LCD with the extended configuration region in NVM */
+	ret_val = e1000_sw_lcd_config_ich8lan(hw);
+	if (ret_val)
+		goto out;
 
-			ret_val = e1e_wphy(hw, (u32)reg_addr, reg_data);
-			if (ret_val)
-				return ret_val;
-		}
-	}
+	/* Configure the LCD with the OEM bits in NVM */
+	if (hw->mac.type == e1000_pchlan)
+		ret_val = e1000_oem_bits_config_ich8lan(hw, true);
 
+out:
 	return 0;
 }
 
@@ -2306,6 +2583,7 @@ static s32 e1000_get_bus_info_ich8lan(struct e1000_hw *hw)
  **/
 static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw)
 {
+	struct e1000_dev_spec_ich8lan *dev_spec = &hw->dev_spec.ich8lan;
 	u16 reg;
 	u32 ctrl, icr, kab;
 	s32 ret_val;
@@ -2341,6 +2619,18 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw)
 		ew32(PBS, E1000_PBS_16K);
 	}
 
+	if (hw->mac.type == e1000_pchlan) {
+		/* Save the NVM K1 bit setting*/
+		ret_val = e1000_read_nvm(hw, E1000_NVM_K1_CONFIG, 1, &reg);
+		if (ret_val)
+			return ret_val;
+
+		if (reg & E1000_NVM_K1_ENABLE)
+			dev_spec->nvm_k1_enabled = true;
+		else
+			dev_spec->nvm_k1_enabled = false;
+	}
+
 	ctrl = er32(CTRL);
 
 	if (!e1000_check_reset_block(hw)) {
@@ -2386,6 +2676,15 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw)
 	if (hw->mac.type == e1000_pchlan)
 		e1e_rphy(hw, BM_WUC, &reg);
 
+	ret_val = e1000_sw_lcd_config_ich8lan(hw);
+	if (ret_val)
+		goto out;
+
+	if (hw->mac.type == e1000_pchlan) {
+		ret_val = e1000_oem_bits_config_ich8lan(hw, true);
+		if (ret_val)
+			goto out;
+	}
 	/*
 	 * For PCH, this write will make sure that any noise
 	 * will be detected as a CRC error and be dropped rather than show up
@@ -2404,6 +2703,7 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw)
 	if (hw->mac.type == e1000_pchlan)
 		ret_val = e1000_hv_phy_workarounds_ich8lan(hw);
 
+out:
 	return ret_val;
 }
 
@@ -2708,14 +3008,6 @@ static s32 e1000_get_link_up_info_ich8lan(struct e1000_hw *hw, u16 *speed,
 	if (ret_val)
 		return ret_val;
 
-	if ((hw->mac.type == e1000_pchlan) && (*speed == SPEED_1000)) {
-		ret_val = e1000e_write_kmrn_reg(hw,
-		                                  E1000_KMRNCTRLSTA_K1_CONFIG,
-		                                  E1000_KMRNCTRLSTA_K1_DISABLE);
-		if (ret_val)
-			return ret_val;
-	}
-
 	if ((hw->mac.type == e1000_ich8lan) &&
 	    (hw->phy.type == e1000_phy_igp_3) &&
 	    (*speed == SPEED_1000)) {
diff --git a/drivers/net/e1000e/phy.c b/drivers/net/e1000e/phy.c
index f9d33ab05e9..03175b3a2c9 100644
--- a/drivers/net/e1000e/phy.c
+++ b/drivers/net/e1000e/phy.c
@@ -95,13 +95,6 @@ static const u16 e1000_igp_2_cable_length_table[] =
 /* BM PHY Copper Specific Control 1 */
 #define BM_CS_CTRL1                       16
 
-/* BM PHY Copper Specific Status */
-#define BM_CS_STATUS                      17
-#define BM_CS_STATUS_LINK_UP              0x0400
-#define BM_CS_STATUS_RESOLVED             0x0800
-#define BM_CS_STATUS_SPEED_MASK           0xC000
-#define BM_CS_STATUS_SPEED_1000           0x8000
-
 #define HV_MUX_DATA_CTRL               PHY_REG(776, 16)
 #define HV_MUX_DATA_CTRL_GEN_TO_MAC    0x0400
 #define HV_MUX_DATA_CTRL_FORCE_SPEED   0x0004
@@ -563,7 +556,7 @@ s32 e1000e_read_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 *data)
 }
 
 /**
- *  e1000_read_kmrn_reg_locked -  Read kumeran register
+ *  e1000e_read_kmrn_reg_locked -  Read kumeran register
  *  @hw: pointer to the HW structure
  *  @offset: register offset to be read
  *  @data: pointer to the read data
@@ -572,7 +565,7 @@ s32 e1000e_read_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 *data)
  *  information retrieved is stored in data.
  *  Assumes semaphore already acquired.
  **/
-s32 e1000_read_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 *data)
+s32 e1000e_read_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 *data)
 {
 	return __e1000_read_kmrn_reg(hw, offset, data, true);
 }
@@ -631,7 +624,7 @@ s32 e1000e_write_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 data)
 }
 
 /**
- *  e1000_write_kmrn_reg_locked -  Write kumeran register
+ *  e1000e_write_kmrn_reg_locked -  Write kumeran register
  *  @hw: pointer to the HW structure
  *  @offset: register offset to write to
  *  @data: data to write at register offset
@@ -639,7 +632,7 @@ s32 e1000e_write_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 data)
  *  Write the data to PHY register at the offset using the kumeran interface.
  *  Assumes semaphore already acquired.
  **/
-s32 e1000_write_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 data)
+s32 e1000e_write_kmrn_reg_locked(struct e1000_hw *hw, u32 offset, u16 data)
 {
 	return __e1000_write_kmrn_reg(hw, offset, data, true);
 }