summaryrefslogtreecommitdiffstats
path: root/drivers/net/e1000e
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/e1000e')
-rw-r--r--drivers/net/e1000e/82571.c5
-rw-r--r--drivers/net/e1000e/e1000.h51
-rw-r--r--drivers/net/e1000e/es2lan.c8
-rw-r--r--drivers/net/e1000e/ethtool.c1
-rw-r--r--drivers/net/e1000e/hw.h21
-rw-r--r--drivers/net/e1000e/ich8lan.c191
-rw-r--r--drivers/net/e1000e/lib.c4
-rw-r--r--drivers/net/e1000e/netdev.c171
-rw-r--r--drivers/net/e1000e/phy.c352
9 files changed, 512 insertions, 292 deletions
diff --git a/drivers/net/e1000e/82571.c b/drivers/net/e1000e/82571.c
index 8295f219243..480f2592f8a 100644
--- a/drivers/net/e1000e/82571.c
+++ b/drivers/net/e1000e/82571.c
@@ -431,8 +431,6 @@ static s32 e1000_get_variants_82571(struct e1000_adapter *adapter)
adapter->flags &= ~FLAG_HAS_WOL;
break;
case e1000_82573:
- case e1000_82574:
- case e1000_82583:
if (pdev->device == E1000_DEV_ID_82573L) {
adapter->flags |= FLAG_HAS_JUMBO_FRAMES;
adapter->max_hw_frame_size = DEFAULT_JUMBO;
@@ -2104,10 +2102,11 @@ struct e1000_info e1000_82583_info = {
| FLAG_RX_CSUM_ENABLED
| FLAG_HAS_SMART_POWER_DOWN
| FLAG_HAS_AMT
+ | FLAG_HAS_JUMBO_FRAMES
| FLAG_HAS_CTRLEXT_ON_LOAD,
.flags2 = FLAG2_DISABLE_ASPM_L0S,
.pba = 32,
- .max_hw_frame_size = ETH_FRAME_LEN + ETH_FCS_LEN,
+ .max_hw_frame_size = DEFAULT_JUMBO,
.get_variants = e1000_get_variants_82571,
.mac_ops = &e82571_mac_ops,
.phy_ops = &e82_phy_ops_bm,
diff --git a/drivers/net/e1000e/e1000.h b/drivers/net/e1000e/e1000.h
index 9549879e66a..638d175792c 100644
--- a/drivers/net/e1000e/e1000.h
+++ b/drivers/net/e1000e/e1000.h
@@ -104,6 +104,7 @@ struct e1000_info;
(((reg) & ~MAX_PHY_REG_ADDRESS) << (PHY_UPPER_SHIFT - PHY_PAGE_SHIFT)))
/* PHY Wakeup Registers and defines */
+#define BM_PORT_GEN_CFG PHY_REG(BM_PORT_CTRL_PAGE, 17)
#define BM_RCTL PHY_REG(BM_WUC_PAGE, 0)
#define BM_WUC PHY_REG(BM_WUC_PAGE, 1)
#define BM_WUFC PHY_REG(BM_WUC_PAGE, 2)
@@ -122,20 +123,21 @@ struct e1000_info;
#define BM_RCTL_PMCF 0x0040 /* Pass MAC Control Frames */
#define BM_RCTL_RFCE 0x0080 /* Rx Flow Control Enable */
-#define HV_SCC_UPPER PHY_REG(778, 16) /* Single Collision Count */
-#define HV_SCC_LOWER PHY_REG(778, 17)
-#define HV_ECOL_UPPER PHY_REG(778, 18) /* Excessive Collision Count */
-#define HV_ECOL_LOWER PHY_REG(778, 19)
-#define HV_MCC_UPPER PHY_REG(778, 20) /* Multiple Collision Count */
-#define HV_MCC_LOWER PHY_REG(778, 21)
-#define HV_LATECOL_UPPER PHY_REG(778, 23) /* Late Collision Count */
-#define HV_LATECOL_LOWER PHY_REG(778, 24)
-#define HV_COLC_UPPER PHY_REG(778, 25) /* Collision Count */
-#define HV_COLC_LOWER PHY_REG(778, 26)
-#define HV_DC_UPPER PHY_REG(778, 27) /* Defer Count */
-#define HV_DC_LOWER PHY_REG(778, 28)
-#define HV_TNCRS_UPPER PHY_REG(778, 29) /* Transmit with no CRS */
-#define HV_TNCRS_LOWER PHY_REG(778, 30)
+#define HV_STATS_PAGE 778
+#define HV_SCC_UPPER PHY_REG(HV_STATS_PAGE, 16) /* Single Collision Count */
+#define HV_SCC_LOWER PHY_REG(HV_STATS_PAGE, 17)
+#define HV_ECOL_UPPER PHY_REG(HV_STATS_PAGE, 18) /* Excessive Coll. Count */
+#define HV_ECOL_LOWER PHY_REG(HV_STATS_PAGE, 19)
+#define HV_MCC_UPPER PHY_REG(HV_STATS_PAGE, 20) /* Multiple Coll. Count */
+#define HV_MCC_LOWER PHY_REG(HV_STATS_PAGE, 21)
+#define HV_LATECOL_UPPER PHY_REG(HV_STATS_PAGE, 23) /* Late Collision Count */
+#define HV_LATECOL_LOWER PHY_REG(HV_STATS_PAGE, 24)
+#define HV_COLC_UPPER PHY_REG(HV_STATS_PAGE, 25) /* Collision Count */
+#define HV_COLC_LOWER PHY_REG(HV_STATS_PAGE, 26)
+#define HV_DC_UPPER PHY_REG(HV_STATS_PAGE, 27) /* Defer Count */
+#define HV_DC_LOWER PHY_REG(HV_STATS_PAGE, 28)
+#define HV_TNCRS_UPPER PHY_REG(HV_STATS_PAGE, 29) /* Transmit with no CRS */
+#define HV_TNCRS_LOWER PHY_REG(HV_STATS_PAGE, 30)
#define E1000_FCRTV_PCH 0x05F40 /* PCH Flow Control Refresh Timer Value */
@@ -197,11 +199,6 @@ enum e1000_boards {
board_pch2lan,
};
-struct e1000_queue_stats {
- u64 packets;
- u64 bytes;
-};
-
struct e1000_ps_page {
struct page *page;
u64 dma; /* must be u64 - written to hw */
@@ -255,8 +252,6 @@ struct e1000_ring {
int set_itr;
struct sk_buff *rx_skb_top;
-
- struct e1000_queue_stats stats;
};
/* PHY register snapshot values */
@@ -339,7 +334,7 @@ struct e1000_adapter {
int *work_done, int work_to_do)
____cacheline_aligned_in_smp;
void (*alloc_rx_buf) (struct e1000_adapter *adapter,
- int cleaned_count);
+ int cleaned_count, gfp_t gfp);
struct e1000_ring *rx_ring;
u32 rx_int_delay;
@@ -533,7 +528,8 @@ extern void e1000e_set_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw,
bool state);
extern void e1000e_igp3_phy_powerdown_workaround_ich8lan(struct e1000_hw *hw);
extern void e1000e_gig_downshift_workaround_ich8lan(struct e1000_hw *hw);
-extern void e1000e_disable_gig_wol_ich8lan(struct e1000_hw *hw);
+extern void e1000_suspend_workarounds_ich8lan(struct e1000_hw *hw);
+extern void e1000_resume_workarounds_pchlan(struct e1000_hw *hw);
extern s32 e1000_configure_k1_ich8lan(struct e1000_hw *hw, bool k1_enable);
extern s32 e1000_lv_jumbo_workaround_ich8lan(struct e1000_hw *hw, bool enable);
extern void e1000_copy_rx_addrs_to_phy_ich8lan(struct e1000_hw *hw);
@@ -584,6 +580,7 @@ extern s32 e1000e_check_reset_block_generic(struct e1000_hw *hw);
extern s32 e1000e_phy_force_speed_duplex_igp(struct e1000_hw *hw);
extern s32 e1000e_get_cable_length_igp_2(struct e1000_hw *hw);
extern s32 e1000e_get_phy_info_igp(struct e1000_hw *hw);
+extern s32 e1000_set_page_igp(struct e1000_hw *hw, u16 page);
extern s32 e1000e_read_phy_reg_igp(struct e1000_hw *hw, u32 offset, u16 *data);
extern s32 e1000e_read_phy_reg_igp_locked(struct e1000_hw *hw, u32 offset,
u16 *data);
@@ -604,6 +601,10 @@ extern enum e1000_phy_type e1000e_get_phy_type_from_id(u32 phy_id);
extern s32 e1000e_determine_phy_address(struct e1000_hw *hw);
extern s32 e1000e_write_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 data);
extern s32 e1000e_read_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 *data);
+extern s32 e1000_enable_phy_wakeup_reg_access_bm(struct e1000_hw *hw,
+ u16 *phy_reg);
+extern s32 e1000_disable_phy_wakeup_reg_access_bm(struct e1000_hw *hw,
+ u16 *phy_reg);
extern s32 e1000e_read_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 *data);
extern s32 e1000e_write_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 data);
extern void e1000e_phy_force_speed_duplex_setup(struct e1000_hw *hw, u16 *phy_ctrl);
@@ -624,9 +625,13 @@ extern s32 e1000e_check_downshift(struct e1000_hw *hw);
extern s32 e1000_read_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 *data);
extern s32 e1000_read_phy_reg_hv_locked(struct e1000_hw *hw, u32 offset,
u16 *data);
+extern s32 e1000_read_phy_reg_page_hv(struct e1000_hw *hw, u32 offset,
+ u16 *data);
extern s32 e1000_write_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 data);
extern s32 e1000_write_phy_reg_hv_locked(struct e1000_hw *hw, u32 offset,
u16 data);
+extern s32 e1000_write_phy_reg_page_hv(struct e1000_hw *hw, u32 offset,
+ u16 data);
extern s32 e1000_link_stall_workaround_hv(struct e1000_hw *hw);
extern s32 e1000_copper_link_setup_82577(struct e1000_hw *hw);
extern s32 e1000_check_polarity_82577(struct e1000_hw *hw);
diff --git a/drivers/net/e1000e/es2lan.c b/drivers/net/e1000e/es2lan.c
index f4bbeb22f51..c0ecb2d9fdb 100644
--- a/drivers/net/e1000e/es2lan.c
+++ b/drivers/net/e1000e/es2lan.c
@@ -836,6 +836,7 @@ static s32 e1000_init_hw_80003es2lan(struct e1000_hw *hw)
struct e1000_mac_info *mac = &hw->mac;
u32 reg_data;
s32 ret_val;
+ u16 kum_reg_data;
u16 i;
e1000_initialize_hw_bits_80003es2lan(hw);
@@ -861,6 +862,13 @@ static s32 e1000_init_hw_80003es2lan(struct e1000_hw *hw)
/* Setup link and flow control */
ret_val = e1000e_setup_link(hw);
+ /* Disable IBIST slave mode (far-end loopback) */
+ e1000_read_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_INBAND_PARAM,
+ &kum_reg_data);
+ kum_reg_data |= E1000_KMRNCTRLSTA_IBIST_DISABLE;
+ e1000_write_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_INBAND_PARAM,
+ kum_reg_data);
+
/* Set the transmit descriptor write-back policy */
reg_data = er32(TXDCTL(0));
reg_data = (reg_data & ~E1000_TXDCTL_WTHRESH) |
diff --git a/drivers/net/e1000e/ethtool.c b/drivers/net/e1000e/ethtool.c
index 859d0d3af6c..cb1a3623253 100644
--- a/drivers/net/e1000e/ethtool.c
+++ b/drivers/net/e1000e/ethtool.c
@@ -28,6 +28,7 @@
/* ethtool support for e1000 */
+#include <linux/interrupt.h>
#include <linux/netdevice.h>
#include <linux/ethtool.h>
#include <linux/pci.h>
diff --git a/drivers/net/e1000e/hw.h b/drivers/net/e1000e/hw.h
index 6c2fa8327f5..29670397079 100644
--- a/drivers/net/e1000e/hw.h
+++ b/drivers/net/e1000e/hw.h
@@ -246,6 +246,7 @@ enum e1e_registers {
#define BM_WUC_ENABLE_REG 17
#define BM_WUC_ENABLE_BIT (1 << 2)
#define BM_WUC_HOST_WU_BIT (1 << 4)
+#define BM_WUC_ME_WU_BIT (1 << 5)
#define BM_WUC PHY_REG(BM_WUC_PAGE, 1)
#define BM_WUFC PHY_REG(BM_WUC_PAGE, 2)
@@ -312,6 +313,7 @@ enum e1e_registers {
#define E1000_KMRNCTRLSTA_DIAG_OFFSET 0x3 /* Kumeran Diagnostic */
#define E1000_KMRNCTRLSTA_TIMEOUTS 0x4 /* Kumeran Timeouts */
#define E1000_KMRNCTRLSTA_INBAND_PARAM 0x9 /* Kumeran InBand Parameters */
+#define E1000_KMRNCTRLSTA_IBIST_DISABLE 0x0200 /* Kumeran IBIST Disable */
#define E1000_KMRNCTRLSTA_DIAG_NELPBK 0x1000 /* Nearend Loopback mode */
#define E1000_KMRNCTRLSTA_K1_CONFIG 0x7
#define E1000_KMRNCTRLSTA_K1_ENABLE 0x0002
@@ -777,7 +779,21 @@ struct e1000_mac_operations {
s32 (*read_mac_addr)(struct e1000_hw *);
};
-/* Function pointers for the PHY. */
+/*
+ * When to use various PHY register access functions:
+ *
+ * Func Caller
+ * Function Does Does When to use
+ * ~~~~~~~~~~~~ ~~~~~ ~~~~~~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ * X_reg L,P,A n/a for simple PHY reg accesses
+ * X_reg_locked P,A L for multiple accesses of different regs
+ * on different pages
+ * X_reg_page A L,P for multiple accesses of different regs
+ * on the same page
+ *
+ * Where X=[read|write], L=locking, P=sets page, A=register access
+ *
+ */
struct e1000_phy_operations {
s32 (*acquire)(struct e1000_hw *);
s32 (*cfg_on_link_up)(struct e1000_hw *);
@@ -788,14 +804,17 @@ struct e1000_phy_operations {
s32 (*get_cfg_done)(struct e1000_hw *hw);
s32 (*get_cable_length)(struct e1000_hw *);
s32 (*get_info)(struct e1000_hw *);
+ s32 (*set_page)(struct e1000_hw *, u16);
s32 (*read_reg)(struct e1000_hw *, u32, u16 *);
s32 (*read_reg_locked)(struct e1000_hw *, u32, u16 *);
+ s32 (*read_reg_page)(struct e1000_hw *, u32, u16 *);
void (*release)(struct e1000_hw *);
s32 (*reset)(struct e1000_hw *);
s32 (*set_d0_lplu_state)(struct e1000_hw *, bool);
s32 (*set_d3_lplu_state)(struct e1000_hw *, bool);
s32 (*write_reg)(struct e1000_hw *, u32, u16);
s32 (*write_reg_locked)(struct e1000_hw *, u32, u16);
+ s32 (*write_reg_page)(struct e1000_hw *, u32, u16);
void (*power_up)(struct e1000_hw *);
void (*power_down)(struct e1000_hw *);
};
diff --git a/drivers/net/e1000e/ich8lan.c b/drivers/net/e1000e/ich8lan.c
index 3369d1f6a39..c1752124f3c 100644
--- a/drivers/net/e1000e/ich8lan.c
+++ b/drivers/net/e1000e/ich8lan.c
@@ -275,6 +275,19 @@ static inline void __ew32flash(struct e1000_hw *hw, unsigned long reg, u32 val)
#define ew16flash(reg,val) __ew16flash(hw, (reg), (val))
#define ew32flash(reg,val) __ew32flash(hw, (reg), (val))
+static void e1000_toggle_lanphypc_value_ich8lan(struct e1000_hw *hw)
+{
+ u32 ctrl;
+
+ ctrl = er32(CTRL);
+ ctrl |= E1000_CTRL_LANPHYPC_OVERRIDE;
+ ctrl &= ~E1000_CTRL_LANPHYPC_VALUE;
+ ew32(CTRL, ctrl);
+ udelay(10);
+ ctrl &= ~E1000_CTRL_LANPHYPC_OVERRIDE;
+ ew32(CTRL, ctrl);
+}
+
/**
* e1000_init_phy_params_pchlan - Initialize PHY function pointers
* @hw: pointer to the HW structure
@@ -284,18 +297,21 @@ static inline void __ew32flash(struct e1000_hw *hw, unsigned long reg, u32 val)
static s32 e1000_init_phy_params_pchlan(struct e1000_hw *hw)
{
struct e1000_phy_info *phy = &hw->phy;
- u32 ctrl, fwsm;
+ u32 fwsm;
s32 ret_val = 0;
phy->addr = 1;
phy->reset_delay_us = 100;
+ phy->ops.set_page = e1000_set_page_igp;
phy->ops.read_reg = e1000_read_phy_reg_hv;
phy->ops.read_reg_locked = e1000_read_phy_reg_hv_locked;
+ phy->ops.read_reg_page = e1000_read_phy_reg_page_hv;
phy->ops.set_d0_lplu_state = e1000_set_lplu_state_pchlan;
phy->ops.set_d3_lplu_state = e1000_set_lplu_state_pchlan;
phy->ops.write_reg = e1000_write_phy_reg_hv;
phy->ops.write_reg_locked = e1000_write_phy_reg_hv_locked;
+ phy->ops.write_reg_page = e1000_write_phy_reg_page_hv;
phy->ops.power_up = e1000_power_up_phy_copper;
phy->ops.power_down = e1000_power_down_phy_copper_ich8lan;
phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT;
@@ -308,13 +324,7 @@ static s32 e1000_init_phy_params_pchlan(struct e1000_hw *hw)
*/
fwsm = er32(FWSM);
if (!(fwsm & E1000_ICH_FWSM_FW_VALID) && !e1000_check_reset_block(hw)) {
- ctrl = er32(CTRL);
- ctrl |= E1000_CTRL_LANPHYPC_OVERRIDE;
- ctrl &= ~E1000_CTRL_LANPHYPC_VALUE;
- ew32(CTRL, ctrl);
- udelay(10);
- ctrl &= ~E1000_CTRL_LANPHYPC_OVERRIDE;
- ew32(CTRL, ctrl);
+ e1000_toggle_lanphypc_value_ich8lan(hw);
msleep(50);
/*
@@ -882,8 +892,13 @@ static void e1000_release_swflag_ich8lan(struct e1000_hw *hw)
u32 extcnf_ctrl;
extcnf_ctrl = er32(EXTCNF_CTRL);
- extcnf_ctrl &= ~E1000_EXTCNF_CTRL_SWFLAG;
- ew32(EXTCNF_CTRL, extcnf_ctrl);
+
+ if (extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG) {
+ extcnf_ctrl &= ~E1000_EXTCNF_CTRL_SWFLAG;
+ ew32(EXTCNF_CTRL, extcnf_ctrl);
+ } else {
+ e_dbg("Semaphore unexpectedly released by sw/fw/hw\n");
+ }
mutex_unlock(&swflag_mutex);
}
@@ -1376,14 +1391,11 @@ static s32 e1000_hv_phy_workarounds_ich8lan(struct e1000_hw *hw)
ret_val = hw->phy.ops.acquire(hw);
if (ret_val)
goto out;
- ret_val = hw->phy.ops.read_reg_locked(hw,
- PHY_REG(BM_PORT_CTRL_PAGE, 17),
- &phy_data);
+ ret_val = hw->phy.ops.read_reg_locked(hw, BM_PORT_GEN_CFG, &phy_data);
if (ret_val)
goto release;
- ret_val = hw->phy.ops.write_reg_locked(hw,
- PHY_REG(BM_PORT_CTRL_PAGE, 17),
- phy_data & 0x00FF);
+ ret_val = hw->phy.ops.write_reg_locked(hw, BM_PORT_GEN_CFG,
+ phy_data & 0x00FF);
release:
hw->phy.ops.release(hw);
out:
@@ -1397,17 +1409,36 @@ out:
void e1000_copy_rx_addrs_to_phy_ich8lan(struct e1000_hw *hw)
{
u32 mac_reg;
- u16 i;
+ u16 i, phy_reg = 0;
+ s32 ret_val;
+
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ return;
+ ret_val = e1000_enable_phy_wakeup_reg_access_bm(hw, &phy_reg);
+ if (ret_val)
+ goto release;
/* Copy both RAL/H (rar_entry_count) and SHRAL/H (+4) to PHY */
for (i = 0; i < (hw->mac.rar_entry_count + 4); i++) {
mac_reg = er32(RAL(i));
- e1e_wphy(hw, BM_RAR_L(i), (u16)(mac_reg & 0xFFFF));
- e1e_wphy(hw, BM_RAR_M(i), (u16)((mac_reg >> 16) & 0xFFFF));
+ hw->phy.ops.write_reg_page(hw, BM_RAR_L(i),
+ (u16)(mac_reg & 0xFFFF));
+ hw->phy.ops.write_reg_page(hw, BM_RAR_M(i),
+ (u16)((mac_reg >> 16) & 0xFFFF));
+
mac_reg = er32(RAH(i));
- e1e_wphy(hw, BM_RAR_H(i), (u16)(mac_reg & 0xFFFF));
- e1e_wphy(hw, BM_RAR_CTRL(i), (u16)((mac_reg >> 16) & 0x8000));
+ hw->phy.ops.write_reg_page(hw, BM_RAR_H(i),
+ (u16)(mac_reg & 0xFFFF));
+ hw->phy.ops.write_reg_page(hw, BM_RAR_CTRL(i),
+ (u16)((mac_reg & E1000_RAH_AV)
+ >> 16));
}
+
+ e1000_disable_phy_wakeup_reg_access_bm(hw, &phy_reg);
+
+release:
+ hw->phy.ops.release(hw);
}
/**
@@ -1726,9 +1757,12 @@ static s32 e1000_post_phy_reset_ich8lan(struct e1000_hw *hw)
break;
}
- /* Dummy read to clear the phy wakeup bit after lcd reset */
- if (hw->mac.type >= e1000_pchlan)
- e1e_rphy(hw, BM_WUC, &reg);
+ /* Clear the host wakeup bit after lcd reset */
+ if (hw->mac.type >= e1000_pchlan) {
+ e1e_rphy(hw, BM_PORT_GEN_CFG, &reg);
+ reg &= ~BM_WUC_HOST_WU_BIT;
+ e1e_wphy(hw, BM_PORT_GEN_CFG, reg);
+ }
/* Configure the LCD with the extended configuration region in NVM */
ret_val = e1000_sw_lcd_config_ich8lan(hw);
@@ -3059,7 +3093,7 @@ static s32 e1000_reset_hw_ich8lan(struct e1000_hw *hw)
msleep(20);
if (!ret_val)
- e1000_release_swflag_ich8lan(hw);
+ mutex_unlock(&swflag_mutex);
if (ctrl & E1000_CTRL_PHY_RST) {
ret_val = hw->phy.ops.get_cfg_done(hw);
@@ -3127,11 +3161,13 @@ static s32 e1000_init_hw_ich8lan(struct e1000_hw *hw)
/*
* The 82578 Rx buffer will stall if wakeup is enabled in host and
- * the ME. Reading the BM_WUC register will clear the host wakeup bit.
+ * the ME. Disable wakeup by clearing the host wakeup bit.
* Reset the phy after disabling host wakeup to reset the Rx buffer.
*/
if (hw->phy.type == e1000_phy_82578) {
- e1e_rphy(hw, BM_WUC, &i);
+ e1e_rphy(hw, BM_PORT_GEN_CFG, &i);
+ i &= ~BM_WUC_HOST_WU_BIT;
+ e1e_wphy(hw, BM_PORT_GEN_CFG, i);
ret_val = e1000_phy_hw_reset_ich8lan(hw);
if (ret_val)
return ret_val;
@@ -3586,17 +3622,16 @@ void e1000e_gig_downshift_workaround_ich8lan(struct e1000_hw *hw)
}
/**
- * e1000e_disable_gig_wol_ich8lan - disable gig during WoL
+ * e1000_suspend_workarounds_ich8lan - workarounds needed during S0->Sx
* @hw: pointer to the HW structure
*
* During S0 to Sx transition, it is possible the link remains at gig
* instead of negotiating to a lower speed. Before going to Sx, set
* 'LPLU Enabled' and 'Gig Disable' to force link speed negotiation
- * to a lower speed.
- *
- * Should only be called for applicable parts.
+ * to a lower speed. For PCH and newer parts, the OEM bits PHY register
+ * (LED, GbE disable and LPLU configurations) also needs to be written.
**/
-void e1000e_disable_gig_wol_ich8lan(struct e1000_hw *hw)
+void e1000_suspend_workarounds_ich8lan(struct e1000_hw *hw)
{
u32 phy_ctrl;
s32 ret_val;
@@ -3616,6 +3651,60 @@ void e1000e_disable_gig_wol_ich8lan(struct e1000_hw *hw)
}
/**
+ * e1000_resume_workarounds_pchlan - workarounds needed during Sx->S0
+ * @hw: pointer to the HW structure
+ *
+ * During Sx to S0 transitions on non-managed devices or managed devices
+ * on which PHY resets are not blocked, if the PHY registers cannot be
+ * accessed properly by the s/w toggle the LANPHYPC value to power cycle
+ * the PHY.
+ **/
+void e1000_resume_workarounds_pchlan(struct e1000_hw *hw)
+{
+ u32 fwsm;
+
+ if (hw->mac.type != e1000_pch2lan)
+ return;
+
+ fwsm = er32(FWSM);
+ if (!(fwsm & E1000_ICH_FWSM_FW_VALID) || !e1000_check_reset_block(hw)) {
+ u16 phy_id1, phy_id2;
+ s32 ret_val;
+
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val) {
+ e_dbg("Failed to acquire PHY semaphore in resume\n");
+ return;
+ }
+
+ /* Test access to the PHY registers by reading the ID regs */
+ ret_val = hw->phy.ops.read_reg_locked(hw, PHY_ID1, &phy_id1);
+ if (ret_val)
+ goto release;
+ ret_val = hw->phy.ops.read_reg_locked(hw, PHY_ID2, &phy_id2);
+ if (ret_val)
+ goto release;
+
+ if (hw->phy.id == ((u32)(phy_id1 << 16) |
+ (u32)(phy_id2 & PHY_REVISION_MASK)))
+ goto release;
+
+ e1000_toggle_lanphypc_value_ich8lan(hw);
+
+ hw->phy.ops.release(hw);
+ msleep(50);
+ e1000_phy_hw_reset(hw);
+ msleep(50);
+ return;
+ }
+
+release:
+ hw->phy.ops.release(hw);
+
+ return;
+}
+
+/**
* e1000_cleanup_led_ich8lan - Restore the default LED operation
* @hw: pointer to the HW structure
*
@@ -3832,6 +3921,7 @@ static void e1000_power_down_phy_copper_ich8lan(struct e1000_hw *hw)
static void e1000_clear_hw_cntrs_ich8lan(struct e1000_hw *hw)
{
u16 phy_data;
+ s32 ret_val;
e1000e_clear_hw_cntrs_base(hw);
@@ -3853,20 +3943,29 @@ static void e1000_clear_hw_cntrs_ich8lan(struct e1000_hw *hw)
if ((hw->phy.type == e1000_phy_82578) ||
(hw->phy.type == e1000_phy_82579) ||
(hw->phy.type == e1000_phy_82577)) {
- e1e_rphy(hw, HV_SCC_UPPER, &phy_data);
- e1e_rphy(hw, HV_SCC_LOWER, &phy_data);
- e1e_rphy(hw, HV_ECOL_UPPER, &phy_data);
- e1e_rphy(hw, HV_ECOL_LOWER, &phy_data);
- e1e_rphy(hw, HV_MCC_UPPER, &phy_data);
- e1e_rphy(hw, HV_MCC_LOWER, &phy_data);
- e1e_rphy(hw, HV_LATECOL_UPPER, &phy_data);
- e1e_rphy(hw, HV_LATECOL_LOWER, &phy_data);
- e1e_rphy(hw, HV_COLC_UPPER, &phy_data);
- e1e_rphy(hw, HV_COLC_LOWER, &phy_data);
- e1e_rphy(hw, HV_DC_UPPER, &phy_data);
- e1e_rphy(hw, HV_DC_LOWER, &phy_data);
- e1e_rphy(hw, HV_TNCRS_UPPER, &phy_data);
- e1e_rphy(hw, HV_TNCRS_LOWER, &phy_data);
+ ret_val = hw->phy.ops.acquire(hw);
+ if (ret_val)
+ return;
+ ret_val = hw->phy.ops.set_page(hw,
+ HV_STATS_PAGE << IGP_PAGE_SHIFT);
+ if (ret_val)
+ goto release;
+ hw->phy.ops.read_reg_page(hw, HV_SCC_UPPER, &phy_data);
+ hw->phy.ops.read_reg_page(hw, HV_SCC_LOWER, &phy_data);
+ hw->phy.ops.read_reg_page(hw, HV_ECOL_UPPER, &phy_data);
+ hw->phy.ops.read_reg_page(hw, HV_ECOL_LOWER, &phy_data);
+ hw->phy.ops.read_reg_page(hw, HV_MCC_UPPER, &phy_data);
+ hw->phy.ops.read_reg_page(hw, HV_MCC_LOWER, &phy_data);
+ hw->phy.ops.read_reg_page(hw, HV_LATECOL_UPPER, &phy_data);
+ hw->phy.ops.read_reg_page(hw, HV_LATECOL_LOWER, &phy_data);
+ hw->phy.ops.read_reg_page(hw, HV_COLC_UPPER, &phy_data);
+ hw->phy.ops.read_reg_page(hw, HV_COLC_LOWER, &phy_data);
+ hw->phy.ops.read_reg_page(hw, HV_DC_UPPER, &phy_data);
+ hw->phy.ops.read_reg_page(hw, HV_DC_LOWER, &phy_data);
+ hw->phy.ops.read_reg_page(hw, HV_TNCRS_UPPER, &phy_data);
+ hw->phy.ops.read_reg_page(hw, HV_TNCRS_LOWER, &phy_data);
+release:
+ hw->phy.ops.release(hw);
}
}
diff --git a/drivers/net/e1000e/lib.c b/drivers/net/e1000e/lib.c
index dd8ab05b559..65580b40594 100644
--- a/drivers/net/e1000e/lib.c
+++ b/drivers/net/e1000e/lib.c
@@ -56,7 +56,7 @@ s32 e1000e_get_bus_info_pcie(struct e1000_hw *hw)
struct e1000_adapter *adapter = hw->adapter;
u16 pcie_link_status, cap_offset;
- cap_offset = pci_find_capability(adapter->pdev, PCI_CAP_ID_EXP);
+ cap_offset = adapter->pdev->pcie_cap;
if (!cap_offset) {
bus->width = e1000_bus_width_unknown;
} else {
@@ -220,7 +220,7 @@ s32 e1000_check_alt_mac_addr_generic(struct e1000_hw *hw)
}
/* if multicast bit is set, the alternate address will not be used */
- if (alt_mac_addr[0] & 0x01) {
+ if (is_multicast_ether_addr(alt_mac_addr)) {
e_dbg("Ignoring Alternate Mac Address with MC bit set\n");
goto out;
}
diff --git a/drivers/net/e1000e/netdev.c b/drivers/net/e1000e/netdev.c
index 3310c3d477d..4353ad56cf1 100644
--- a/drivers/net/e1000e/netdev.c
+++ b/drivers/net/e1000e/netdev.c
@@ -31,6 +31,7 @@
#include <linux/module.h>
#include <linux/types.h>
#include <linux/init.h>
+#include <linux/interrupt.h>
#include <linux/pci.h>
#include <linux/vmalloc.h>
#include <linux/pagemap.h>
@@ -53,9 +54,9 @@
#include "e1000.h"
-#define DRV_EXTRAVERSION "-k2"
+#define DRV_EXTRAVERSION "-k"
-#define DRV_VERSION "1.3.10" DRV_EXTRAVERSION
+#define DRV_VERSION "1.3.16" DRV_EXTRAVERSION
char e1000e_driver_name[] = "e1000e";
const char e1000e_driver_version[] = DRV_VERSION;
@@ -522,7 +523,7 @@ static void e1000_rx_checksum(struct e1000_adapter *adapter, u32 status_err,
* @adapter: address of board private structure
**/
static void e1000_alloc_rx_buffers(struct e1000_adapter *adapter,
- int cleaned_count)
+ int cleaned_count, gfp_t gfp)
{
struct net_device *netdev = adapter->netdev;
struct pci_dev *pdev = adapter->pdev;
@@ -543,7 +544,7 @@ static void e1000_alloc_rx_buffers(struct e1000_adapter *adapter,
goto map_skb;
}
- skb = netdev_alloc_skb_ip_align(netdev, bufsz);
+ skb = __netdev_alloc_skb_ip_align(netdev, bufsz, gfp);
if (!skb) {
/* Better luck next round */
adapter->alloc_rx_buff_failed++;
@@ -588,7 +589,7 @@ map_skb:
* @adapter: address of board private structure
**/
static void e1000_alloc_rx_buffers_ps(struct e1000_adapter *adapter,
- int cleaned_count)
+ int cleaned_count, gfp_t gfp)
{
struct net_device *netdev = adapter->netdev;
struct pci_dev *pdev = adapter->pdev;
@@ -614,7 +615,7 @@ static void e1000_alloc_rx_buffers_ps(struct e1000_adapter *adapter,
continue;
}
if (!ps_page->page) {
- ps_page->page = alloc_page(GFP_ATOMIC);
+ ps_page->page = alloc_page(gfp);
if (!ps_page->page) {
adapter->alloc_rx_buff_failed++;
goto no_buffers;
@@ -640,8 +641,9 @@ static void e1000_alloc_rx_buffers_ps(struct e1000_adapter *adapter,
cpu_to_le64(ps_page->dma);
}
- skb = netdev_alloc_skb_ip_align(netdev,
- adapter->rx_ps_bsize0);
+ skb = __netdev_alloc_skb_ip_align(netdev,
+ adapter->rx_ps_bsize0,
+ gfp);
if (!skb) {
adapter->alloc_rx_buff_failed++;
@@ -691,7 +693,7 @@ no_buffers:
**/
static void e1000_alloc_jumbo_rx_buffers(struct e1000_adapter *adapter,
- int cleaned_count)
+ int cleaned_count, gfp_t gfp)
{
struct net_device *netdev = adapter->netdev;
struct pci_dev *pdev = adapter->pdev;
@@ -712,7 +714,7 @@ static void e1000_alloc_jumbo_rx_buffers(struct e1000_adapter *adapter,
goto check_page;
}
- skb = netdev_alloc_skb_ip_align(netdev, bufsz);
+ skb = __netdev_alloc_skb_ip_align(netdev, bufsz, gfp);
if (unlikely(!skb)) {
/* Better luck next round */
adapter->alloc_rx_buff_failed++;
@@ -723,7 +725,7 @@ static void e1000_alloc_jumbo_rx_buffers(struct e1000_adapter *adapter,
check_page:
/* allocate a new page if necessary */
if (!buffer_info->page) {
- buffer_info->page = alloc_page(GFP_ATOMIC);
+ buffer_info->page = alloc_page(gfp);
if (unlikely(!buffer_info->page)) {
adapter->alloc_rx_buff_failed++;
break;
@@ -887,7 +889,8 @@ next_desc:
/* return some buffers to hardware, one at a time is too slow */
if (cleaned_count >= E1000_RX_BUFFER_WRITE) {
- adapter->alloc_rx_buf(adapter, cleaned_count);
+ adapter->alloc_rx_buf(adapter, cleaned_count,
+ GFP_ATOMIC);
cleaned_count = 0;
}
@@ -899,7 +902,7 @@ next_desc:
cleaned_count = e1000_desc_unused(rx_ring);
if (cleaned_count)
- adapter->alloc_rx_buf(adapter, cleaned_count);
+ adapter->alloc_rx_buf(adapter, cleaned_count, GFP_ATOMIC);
adapter->total_rx_bytes += total_rx_bytes;
adapter->total_rx_packets += total_rx_packets;
@@ -1229,7 +1232,8 @@ next_desc:
/* return some buffers to hardware, one at a time is too slow */
if (cleaned_count >= E1000_RX_BUFFER_WRITE) {
- adapter->alloc_rx_buf(adapter, cleaned_count);
+ adapter->alloc_rx_buf(adapter, cleaned_count,
+ GFP_ATOMIC);
cleaned_count = 0;
}
@@ -1243,7 +1247,7 @@ next_desc:
cleaned_count = e1000_desc_unused(rx_ring);
if (cleaned_count)
- adapter->alloc_rx_buf(adapter, cleaned_count);
+ adapter->alloc_rx_buf(adapter, cleaned_count, GFP_ATOMIC);
adapter->total_rx_bytes += total_rx_bytes;
adapter->total_rx_packets += total_rx_packets;
@@ -1410,7 +1414,8 @@ next_desc:
/* return some buffers to hardware, one at a time is too slow */
if (unlikely(cleaned_count >= E1000_RX_BUFFER_WRITE)) {
- adapter->alloc_rx_buf(adapter, cleaned_count);
+ adapter->alloc_rx_buf(adapter, cleaned_count,
+ GFP_ATOMIC);
cleaned_count = 0;
}
@@ -1422,7 +1427,7 @@ next_desc:
cleaned_count = e1000_desc_unused(rx_ring);
if (cleaned_count)
- adapter->alloc_rx_buf(adapter, cleaned_count);
+ adapter->alloc_rx_buf(adapter, cleaned_count, GFP_ATOMIC);
adapter->total_rx_bytes += total_rx_bytes;
adapter->total_rx_packets += total_rx_packets;
@@ -3104,7 +3109,8 @@ static void e1000_configure(struct e1000_adapter *adapter)
e1000_configure_tx(adapter);
e1000_setup_rctl(adapter);
e1000_configure_rx(adapter);
- adapter->alloc_rx_buf(adapter, e1000_desc_unused(adapter->rx_ring));
+ adapter->alloc_rx_buf(adapter, e1000_desc_unused(adapter->rx_ring),
+ GFP_KERNEL);
}
/**
@@ -3346,7 +3352,7 @@ int e1000e_up(struct e1000_adapter *adapter)
e1000_configure_msix(adapter);
e1000_irq_enable(adapter);
- netif_wake_queue(adapter->netdev);
+ netif_start_queue(adapter->netdev);
/* fire a link change interrupt to start the watchdog */
if (adapter->msix_entries)
@@ -3413,17 +3419,16 @@ void e1000e_down(struct e1000_adapter *adapter)
e1000e_update_stats(adapter);
spin_unlock(&adapter->stats64_lock);
+ e1000e_flush_descriptors(adapter);
+ e1000_clean_tx_ring(adapter);
+ e1000_clean_rx_ring(adapter);
+
adapter->link_speed = 0;
adapter->link_duplex = 0;
if (!pci_channel_offline(adapter->pdev))
e1000e_reset(adapter);
- e1000e_flush_descriptors(adapter);
-
- e1000_clean_tx_ring(adapter);
- e1000_clean_rx_ring(adapter);
-
/*
* TODO: for power management, we could drop the link and
* pci_disable_device here.
@@ -3833,6 +3838,8 @@ static void e1000_update_phy_info(unsigned long data)
/**
* e1000e_update_phy_stats - Update the PHY statistics counters
* @adapter: board private structure
+ *
+ * Read/clear the upper 16-bit PHY registers and read/accumulate lower
**/
static void e1000e_update_phy_stats(struct e1000_adapter *adapter)
{
@@ -3844,89 +3851,61 @@ static void e1000e_update_phy_stats(struct e1000_adapter *adapter)
if (ret_val)
return;
- hw->phy.addr = 1;
-
-#define HV_PHY_STATS_PAGE 778
/*
* A page set is expensive so check if already on desired page.
* If not, set to the page with the PHY status registers.
*/
+ hw->phy.addr = 1;
ret_val = e1000e_read_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT,
&phy_data);
if (ret_val)
goto release;
- if (phy_data != (HV_PHY_STATS_PAGE << IGP_PAGE_SHIFT)) {
- ret_val = e1000e_write_phy_reg_mdic(hw,
- IGP01E1000_PHY_PAGE_SELECT,
- (HV_PHY_STATS_PAGE <<
- IGP_PAGE_SHIFT));
+ if (phy_data != (HV_STATS_PAGE << IGP_PAGE_SHIFT)) {
+ ret_val = hw->phy.ops.set_page(hw,
+ HV_STATS_PAGE << IGP_PAGE_SHIFT);
if (ret_val)
goto release;
}
- /* Read/clear the upper 16-bit registers and read/accumulate lower */
-
/* Single Collision Count */
- e1000e_read_phy_reg_mdic(hw, HV_SCC_UPPER & MAX_PHY_REG_ADDRESS,
- &phy_data);
- ret_val = e1000e_read_phy_reg_mdic(hw,
- HV_SCC_LOWER & MAX_PHY_REG_ADDRESS,
- &phy_data);
+ hw->phy.ops.read_reg_page(hw, HV_SCC_UPPER, &phy_data);
+ ret_val = hw->phy.ops.read_reg_page(hw, HV_SCC_LOWER, &phy_data);
if (!ret_val)
adapter->stats.scc += phy_data;
/* Excessive Collision Count */
- e1000e_read_phy_reg_mdic(hw, HV_ECOL_UPPER & MAX_PHY_REG_ADDRESS,
- &phy_data);
- ret_val = e1000e_read_phy_reg_mdic(hw,
- HV_ECOL_LOWER & MAX_PHY_REG_ADDRESS,
- &phy_data);
+ hw->phy.ops.read_reg_page(hw, HV_ECOL_UPPER, &phy_data);
+ ret_val = hw->phy.ops.read_reg_page(hw, HV_ECOL_LOWER, &phy_data);
if (!ret_val)
adapter->stats.ecol += phy_data;
/* Multiple Collision Count */
- e1000e_read_phy_reg_mdic(hw, HV_MCC_UPPER & MAX_PHY_REG_ADDRESS,
- &phy_data);
- ret_val = e1000e_read_phy_reg_mdic(hw,
- HV_MCC_LOWER & MAX_PHY_REG_ADDRESS,
- &phy_data);
+ hw->phy.ops.read_reg_page(hw, HV_MCC_UPPER, &phy_data);
+ ret_val = hw->phy.ops.read_reg_page(hw, HV_MCC_LOWER, &phy_data);
if (!ret_val)
adapter->stats.mcc += phy_data;
/* Late Collision Count */
- e1000e_read_phy_reg_mdic(hw, HV_LATECOL_UPPER & MAX_PHY_REG_ADDRESS,
- &phy_data);
- ret_val = e1000e_read_phy_reg_mdic(hw,
- HV_LATECOL_LOWER &
- MAX_PHY_REG_ADDRESS,
- &phy_data);
+ hw->phy.ops.read_reg_page(hw, HV_LATECOL_UPPER, &phy_data);
+ ret_val = hw->phy.ops.read_reg_page(hw, HV_LATECOL_LOWER, &phy_data);
if (!ret_val)
adapter->stats.latecol += phy_data;
/* Collision Count - also used for adaptive IFS */
- e1000e_read_phy_reg_mdic(hw, HV_COLC_UPPER & MAX_PHY_REG_ADDRESS,
- &phy_data);
- ret_val = e1000e_read_phy_reg_mdic(hw,
- HV_COLC_LOWER & MAX_PHY_REG_ADDRESS,
- &phy_data);
+ hw->phy.ops.read_reg_page(hw, HV_COLC_UPPER, &phy_data);
+ ret_val = hw->phy.ops.read_reg_page(hw, HV_COLC_LOWER, &phy_data);
if (!ret_val)
hw->mac.collision_delta = phy_data;
/* Defer Count */
- e1000e_read_phy_reg_mdic(hw, HV_DC_UPPER & MAX_PHY_REG_ADDRESS,
- &phy_data);
- ret_val = e1000e_read_phy_reg_mdic(hw,
- HV_DC_LOWER & MAX_PHY_REG_ADDRESS,
- &phy_data);
+ hw->phy.ops.read_reg_page(hw, HV_DC_UPPER, &phy_data);
+ ret_val = hw->phy.ops.read_reg_page(hw, HV_DC_LOWER, &phy_data);
if (!ret_val)
adapter->stats.dc += phy_data;
/* Transmit with no CRS */
- e1000e_read_phy_reg_mdic(hw, HV_TNCRS_UPPER & MAX_PHY_REG_ADDRESS,
- &phy_data);
- ret_val = e1000e_read_phy_reg_mdic(hw,
- HV_TNCRS_LOWER & MAX_PHY_REG_ADDRESS,
- &phy_data);
+ hw->phy.ops.read_reg_page(hw, HV_TNCRS_UPPER, &phy_data);
+ ret_val = hw->phy.ops.read_reg_page(hw, HV_TNCRS_LOWER, &phy_data);
if (!ret_val)
adapter->stats.tncrs += phy_data;
@@ -5154,21 +5133,34 @@ static int e1000_init_phy_wakeup(struct e1000_adapter *adapter, u32 wufc)
{
struct e1000_hw *hw = &adapter->hw;
u32 i, mac_reg;
- u16 phy_reg;
+ u16 phy_reg, wuc_enable;
int retval = 0;
/* copy MAC RARs to PHY RARs */
e1000_copy_rx_addrs_to_phy_ich8lan(hw);
- /* copy MAC MTA to PHY MTA */
+ retval = hw->phy.ops.acquire(hw);
+ if (retval) {
+ e_err("Could not acquire PHY\n");
+ return retval;
+ }
+
+ /* Enable access to wakeup registers on and set page to BM_WUC_PAGE */
+ retval = e1000_enable_phy_wakeup_reg_access_bm(hw, &wuc_enable);
+ if (retval)
+ goto out;
+
+ /* copy MAC MTA to PHY MTA - only needed for pchlan */
for (i = 0; i < adapter->hw.mac.mta_reg_count; i++) {
mac_reg = E1000_READ_REG_ARRAY(hw, E1000_MTA, i);
- e1e_wphy(hw, BM_MTA(i), (u16)(mac_reg & 0xFFFF));
- e1e_wphy(hw, BM_MTA(i) + 1, (u16)((mac_reg >> 16) & 0xFFFF));
+ hw->phy.ops.write_reg_page(hw, BM_MTA(i),
+ (u16)(mac_reg & 0xFFFF));
+ hw->phy.ops.write_reg_page(hw, BM_MTA(i) + 1,
+ (u16)((mac_reg >> 16) & 0xFFFF));
}
/* configure PHY Rx Control register */
- e1e_rphy(&adapter->hw, BM_RCTL, &phy_reg);
+ hw->phy.ops.read_reg_page(&adapter->hw, BM_RCTL, &phy_reg);
mac_reg = er32(RCTL);
if (mac_reg & E1000_RCTL_UPE)
phy_reg |= BM_RCTL_UPE;
@@ -5185,31 +5177,19 @@ static int e1000_init_phy_wakeup(struct e1000_adapter *adapter, u32 wufc)
mac_reg = er32(CTRL);
if (mac_reg & E1000_CTRL_RFCE)
phy_reg |= BM_RCTL_RFCE;
- e1e_wphy(&adapter->hw, BM_RCTL, phy_reg);
+ hw->phy.ops.write_reg_page(&adapter->hw, BM_RCTL, phy_reg);
/* enable PHY wakeup in MAC register */
ew32(WUFC, wufc);
ew32(WUC, E1000_WUC_PHY_WAKE | E1000_WUC_PME_EN);
/* configure and enable PHY wakeup in PHY registers */
- e1e_wphy(&adapter->hw, BM_WUFC, wufc);
- e1e_wphy(&adapter->hw, BM_WUC, E1000_WUC_PME_EN);
+ hw->phy.ops.write_reg_page(&adapter->hw, BM_WUFC, wufc);
+ hw->phy.ops.write_reg_page(&adapter->hw, BM_WUC, E1000_WUC_PME_EN);
/* activate PHY wakeup */
- retval = hw->phy.ops.acquire(hw);
- if (retval) {
- e_err("Could not acquire PHY\n");
- return retval;
- }
- e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT,
- (BM_WUC_ENABLE_PAGE << IGP_PAGE_SHIFT));
- retval = e1000e_read_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, &phy_reg);
- if (retval) {
- e_err("Could not read PHY page 769\n");
- goto out;
- }
- phy_reg |= BM_WUC_ENABLE_BIT | BM_WUC_HOST_WU_BIT;
- retval = e1000e_write_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, phy_reg);
+ wuc_enable |= BM_WUC_ENABLE_BIT | BM_WUC_HOST_WU_BIT;
+ retval = e1000_disable_phy_wakeup_reg_access_bm(hw, &wuc_enable);
if (retval)
e_err("Could not set PHY Host Wakeup bit\n");
out:
@@ -5277,7 +5257,7 @@ static int __e1000_shutdown(struct pci_dev *pdev, bool *enable_wake,
}
if (adapter->flags & FLAG_IS_ICH)
- e1000e_disable_gig_wol_ich8lan(&adapter->hw);
+ e1000_suspend_workarounds_ich8lan(&adapter->hw);
/* Allow time for pending master requests to run */
e1000e_disable_pcie_master(&adapter->hw);
@@ -5343,7 +5323,7 @@ static void e1000_complete_shutdown(struct pci_dev *pdev, bool sleep,
*/
if (adapter->flags & FLAG_IS_QUAD_PORT) {
struct pci_dev *us_dev = pdev->bus->self;
- int pos = pci_find_capability(us_dev, PCI_CAP_ID_EXP);
+ int pos = pci_pcie_cap(us_dev);
u16 devctl;
pci_read_config_word(us_dev, pos + PCI_EXP_DEVCTL, &devctl);
@@ -5428,6 +5408,9 @@ static int __e1000_resume(struct pci_dev *pdev)
return err;
}
+ if (hw->mac.type == e1000_pch2lan)
+ e1000_resume_workarounds_pchlan(&adapter->hw);
+
e1000e_power_up_phy(adapter);
/* report the system wakeup cause from S3/S4 */
diff --git a/drivers/net/e1000e/phy.c b/drivers/net/e1000e/phy.c
index 484774c13c2..2a6ee13285b 100644
--- a/drivers/net/e1000e/phy.c
+++ b/drivers/net/e1000e/phy.c
@@ -36,7 +36,7 @@ static s32 e1000_set_d0_lplu_state(struct e1000_hw *hw, bool active);
static s32 e1000_wait_autoneg(struct e1000_hw *hw);
static u32 e1000_get_phy_addr_for_bm_page(u32 page, u32 reg);
static s32 e1000_access_phy_wakeup_reg_bm(struct e1000_hw *hw, u32 offset,
- u16 *data, bool read);
+ u16 *data, bool read, bool page_set);
static u32 e1000_get_phy_addr_for_hv_page(u32 page);
static s32 e1000_access_phy_debug_regs_hv(struct e1000_hw *hw, u32 offset,
u16 *data, bool read);
@@ -348,6 +348,24 @@ s32 e1000e_write_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 data)
}
/**
+ * e1000_set_page_igp - Set page as on IGP-like PHY(s)
+ * @hw: pointer to the HW structure
+ * @page: page to set (shifted left when necessary)
+ *
+ * Sets PHY page required for PHY register access. Assumes semaphore is
+ * already acquired. Note, this function sets phy.addr to 1 so the caller
+ * must set it appropriately (if necessary) after this function returns.
+ **/
+s32 e1000_set_page_igp(struct e1000_hw *hw, u16 page)
+{
+ e_dbg("Setting page 0x%x\n", page);
+
+ hw->phy.addr = 1;
+
+ return e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT, page);
+}
+
+/**
* __e1000e_read_phy_reg_igp - Read igp PHY register
* @hw: pointer to the HW structure
* @offset: register offset to be read
@@ -2418,7 +2436,7 @@ s32 e1000e_write_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 data)
/* Page 800 works differently than the rest so it has its own func */
if (page == BM_WUC_PAGE) {
ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset, &data,
- false);
+ false, false);
goto out;
}
@@ -2477,7 +2495,7 @@ s32 e1000e_read_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 *data)
/* Page 800 works differently than the rest so it has its own func */
if (page == BM_WUC_PAGE) {
ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset, data,
- true);
+ true, false);
goto out;
}
@@ -2535,7 +2553,7 @@ s32 e1000e_read_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 *data)
/* Page 800 works differently than the rest so it has its own func */
if (page == BM_WUC_PAGE) {
ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset, data,
- true);
+ true, false);
goto out;
}
@@ -2579,7 +2597,7 @@ s32 e1000e_write_phy_reg_bm2(struct e1000_hw *hw, u32 offset, u16 data)
/* Page 800 works differently than the rest so it has its own func */
if (page == BM_WUC_PAGE) {
ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset, &data,
- false);
+ false, false);
goto out;
}
@@ -2603,104 +2621,163 @@ out:
}
/**
- * e1000_access_phy_wakeup_reg_bm - Read BM PHY wakeup register
+ * e1000_enable_phy_wakeup_reg_access_bm - enable access to BM wakeup registers
* @hw: pointer to the HW structure
- * @offset: register offset to be read or written
- * @data: pointer to the data to read or write
- * @read: determines if operation is read or write
+ * @phy_reg: pointer to store original contents of BM_WUC_ENABLE_REG
*
- * Acquires semaphore, if necessary, then reads the PHY register at offset
- * and storing the retrieved information in data. Release any acquired
- * semaphores before exiting. Note that procedure to read the wakeup
- * registers are different. It works as such:
- * 1) Set page 769, register 17, bit 2 = 1
- * 2) Set page to 800 for host (801 if we were manageability)
- * 3) Write the address using the address opcode (0x11)
- * 4) Read or write the data using the data opcode (0x12)
- * 5) Restore 769_17.2 to its original value
- *
- * Assumes semaphore already acquired.
+ * Assumes semaphore already acquired and phy_reg points to a valid memory
+ * address to store contents of the BM_WUC_ENABLE_REG register.
**/
-static s32 e1000_access_phy_wakeup_reg_bm(struct e1000_hw *hw, u32 offset,
- u16 *data, bool read)
+s32 e1000_enable_phy_wakeup_reg_access_bm(struct e1000_hw *hw, u16 *phy_reg)
{
s32 ret_val;
- u16 reg = BM_PHY_REG_NUM(offset);
- u16 phy_reg = 0;
+ u16 temp;
- /* Gig must be disabled for MDIO accesses to page 800 */
- if ((hw->mac.type == e1000_pchlan) &&
- (!(er32(PHY_CTRL) & E1000_PHY_CTRL_GBE_DISABLE)))
- e_dbg("Attempting to access page 800 while gig enabled.\n");
-
- /* All operations in this function are phy address 1 */
+ /* All page select, port ctrl and wakeup registers use phy address 1 */
hw->phy.addr = 1;
- /* Set page 769 */
- e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT,
- (BM_WUC_ENABLE_PAGE << IGP_PAGE_SHIFT));
+ /* Select Port Control Registers page */
+ ret_val = e1000_set_page_igp(hw, (BM_PORT_CTRL_PAGE << IGP_PAGE_SHIFT));
+ if (ret_val) {
+ e_dbg("Could not set Port Control page\n");
+ goto out;
+ }
- ret_val = e1000e_read_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, &phy_reg);
+ ret_val = e1000e_read_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, phy_reg);
if (ret_val) {
- e_dbg("Could not read PHY page 769\n");
+ e_dbg("Could not read PHY register %d.%d\n",
+ BM_PORT_CTRL_PAGE, BM_WUC_ENABLE_REG);
goto out;
}
- /* First clear bit 4 to avoid a power state change */
- phy_reg &= ~(BM_WUC_HOST_WU_BIT);
- ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, phy_reg);
+ /*
+ * Enable both PHY wakeup mode and Wakeup register page writes.
+ * Prevent a power state change by disabling ME and Host PHY wakeup.
+ */
+ temp = *phy_reg;
+ temp |= BM_WUC_ENABLE_BIT;
+ temp &= ~(BM_WUC_ME_WU_BIT | BM_WUC_HOST_WU_BIT);
+
+ ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, temp);
if (ret_val) {
- e_dbg("Could not clear PHY page 769 bit 4\n");
+ e_dbg("Could not write PHY register %d.%d\n",
+ BM_PORT_CTRL_PAGE, BM_WUC_ENABLE_REG);
goto out;
}
- /* Write bit 2 = 1, and clear bit 4 to 769_17 */
- ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_ENABLE_REG,
- phy_reg | BM_WUC_ENABLE_BIT);
+ /* Select Host Wakeup Registers page */
+ ret_val = e1000_set_page_igp(hw, (BM_WUC_PAGE << IGP_PAGE_SHIFT));
+
+ /* caller now able to write registers on the Wakeup registers page */
+out:
+ return ret_val;
+}
+
+/**
+ * e1000_disable_phy_wakeup_reg_access_bm - disable access to BM wakeup regs
+ * @hw: pointer to the HW structure
+ * @phy_reg: pointer to original contents of BM_WUC_ENABLE_REG
+ *
+ * Restore BM_WUC_ENABLE_REG to its original value.
+ *
+ * Assumes semaphore already acquired and *phy_reg is the contents of the
+ * BM_WUC_ENABLE_REG before register(s) on BM_WUC_PAGE were accessed by
+ * caller.
+ **/
+s32 e1000_disable_phy_wakeup_reg_access_bm(struct e1000_hw *hw, u16 *phy_reg)
+{
+ s32 ret_val = 0;
+
+ /* Select Port Control Registers page */
+ ret_val = e1000_set_page_igp(hw, (BM_PORT_CTRL_PAGE << IGP_PAGE_SHIFT));
if (ret_val) {
- e_dbg("Could not write PHY page 769 bit 2\n");
+ e_dbg("Could not set Port Control page\n");
goto out;
}
- /* Select page 800 */
- ret_val = e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT,
- (BM_WUC_PAGE << IGP_PAGE_SHIFT));
+ /* Restore 769.17 to its original value */
+ ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, *phy_reg);
+ if (ret_val)
+ e_dbg("Could not restore PHY register %d.%d\n",
+ BM_PORT_CTRL_PAGE, BM_WUC_ENABLE_REG);
+out:
+ return ret_val;
+}
- /* Write the page 800 offset value using opcode 0x11 */
+/**
+ * e1000_access_phy_wakeup_reg_bm - Read/write BM PHY wakeup register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read or written
+ * @data: pointer to the data to read or write
+ * @read: determines if operation is read or write
+ * @page_set: BM_WUC_PAGE already set and access enabled
+ *
+ * Read the PHY register at offset and store the retrieved information in
+ * data, or write data to PHY register at offset. Note the procedure to
+ * access the PHY wakeup registers is different than reading the other PHY
+ * registers. It works as such:
+ * 1) Set 769.17.2 (page 769, register 17, bit 2) = 1
+ * 2) Set page to 800 for host (801 if we were manageability)
+ * 3) Write the address using the address opcode (0x11)
+ * 4) Read or write the data using the data opcode (0x12)
+ * 5) Restore 769.17.2 to its original value
+ *
+ * Steps 1 and 2 are done by e1000_enable_phy_wakeup_reg_access_bm() and
+ * step 5 is done by e1000_disable_phy_wakeup_reg_access_bm().
+ *
+ * Assumes semaphore is already acquired. When page_set==true, assumes
+ * the PHY page is set to BM_WUC_PAGE (i.e. a function in the call stack
+ * is responsible for calls to e1000_[enable|disable]_phy_wakeup_reg_bm()).
+ **/
+static s32 e1000_access_phy_wakeup_reg_bm(struct e1000_hw *hw, u32 offset,
+ u16 *data, bool read, bool page_set)
+{
+ s32 ret_val;
+ u16 reg = BM_PHY_REG_NUM(offset);
+ u16 page = BM_PHY_REG_PAGE(offset);
+ u16 phy_reg = 0;
+
+ /* Gig must be disabled for MDIO accesses to Host Wakeup reg page */
+ if ((hw->mac.type == e1000_pchlan) &&
+ (!(er32(PHY_CTRL) & E1000_PHY_CTRL_GBE_DISABLE)))
+ e_dbg("Attempting to access page %d while gig enabled.\n",
+ page);
+
+ if (!page_set) {
+ /* Enable access to PHY wakeup registers */
+ ret_val = e1000_enable_phy_wakeup_reg_access_bm(hw, &phy_reg);
+ if (ret_val) {
+ e_dbg("Could not enable PHY wakeup reg access\n");
+ goto out;
+ }
+ }
+
+ e_dbg("Accessing PHY page %d reg 0x%x\n", page, reg);
+
+ /* Write the Wakeup register page offset value using opcode 0x11 */
ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_ADDRESS_OPCODE, reg);
if (ret_val) {
- e_dbg("Could not write address opcode to page 800\n");
+ e_dbg("Could not write address opcode to page %d\n", page);
goto out;
}
if (read) {
- /* Read the page 800 value using opcode 0x12 */
+ /* Read the Wakeup register page value using opcode 0x12 */
ret_val = e1000e_read_phy_reg_mdic(hw, BM_WUC_DATA_OPCODE,
data);
} else {
- /* Write the page 800 value using opcode 0x12 */
+ /* Write the Wakeup register page value using opcode 0x12 */
ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_DATA_OPCODE,
*data);
}
if (ret_val) {
- e_dbg("Could not access data value from page 800\n");
+ e_dbg("Could not access PHY reg %d.%d\n", page, reg);
goto out;
}
- /*
- * Restore 769_17.2 to its original value
- * Set page 769
- */
- e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT,
- (BM_WUC_ENABLE_PAGE << IGP_PAGE_SHIFT));
-
- /* Clear 769_17.2 */
- ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, phy_reg);
- if (ret_val) {
- e_dbg("Could not clear PHY page 769 bit 2\n");
- goto out;
- }
+ if (!page_set)
+ ret_val = e1000_disable_phy_wakeup_reg_access_bm(hw, &phy_reg);
out:
return ret_val;
@@ -2792,11 +2869,12 @@ static s32 e1000_set_d0_lplu_state(struct e1000_hw *hw, bool active)
* semaphore before exiting.
**/
static s32 __e1000_read_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 *data,
- bool locked)
+ bool locked, bool page_set)
{
s32 ret_val;
u16 page = BM_PHY_REG_PAGE(offset);
u16 reg = BM_PHY_REG_NUM(offset);
+ u32 phy_addr = hw->phy.addr = e1000_get_phy_addr_for_hv_page(page);
if (!locked) {
ret_val = hw->phy.ops.acquire(hw);
@@ -2806,8 +2884,8 @@ static s32 __e1000_read_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 *data,
/* Page 800 works differently than the rest so it has its own func */
if (page == BM_WUC_PAGE) {
- ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset,
- data, true);
+ ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset, data,
+ true, page_set);
goto out;
}
@@ -2817,26 +2895,25 @@ static s32 __e1000_read_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 *data,
goto out;
}
- hw->phy.addr = e1000_get_phy_addr_for_hv_page(page);
-
- if (page == HV_INTC_FC_PAGE_START)
- page = 0;
+ if (!page_set) {
+ if (page == HV_INTC_FC_PAGE_START)
+ page = 0;
- if (reg > MAX_PHY_MULTI_PAGE_REG) {
- u32 phy_addr = hw->phy.addr;
+ if (reg > MAX_PHY_MULTI_PAGE_REG) {
+ /* Page is shifted left, PHY expects (page x 32) */
+ ret_val = e1000_set_page_igp(hw,
+ (page << IGP_PAGE_SHIFT));
- hw->phy.addr = 1;
-
- /* Page is shifted left, PHY expects (page x 32) */
- ret_val = e1000e_write_phy_reg_mdic(hw,
- IGP01E1000_PHY_PAGE_SELECT,
- (page << IGP_PAGE_SHIFT));
- hw->phy.addr = phy_addr;
+ hw->phy.addr = phy_addr;
- if (ret_val)
- goto out;
+ if (ret_val)
+ goto out;
+ }
}
+ e_dbg("reading PHY page %d (or 0x%x shifted) reg 0x%x\n", page,
+ page << IGP_PAGE_SHIFT, reg);
+
ret_val = e1000e_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & reg,
data);
out:
@@ -2858,7 +2935,7 @@ out:
**/
s32 e1000_read_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 *data)
{
- return __e1000_read_phy_reg_hv(hw, offset, data, false);
+ return __e1000_read_phy_reg_hv(hw, offset, data, false, false);
}
/**
@@ -2872,7 +2949,21 @@ s32 e1000_read_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 *data)
**/
s32 e1000_read_phy_reg_hv_locked(struct e1000_hw *hw, u32 offset, u16 *data)
{
- return __e1000_read_phy_reg_hv(hw, offset, data, true);
+ return __e1000_read_phy_reg_hv(hw, offset, data, true, false);
+}
+
+/**
+ * e1000_read_phy_reg_page_hv - Read HV PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Reads the PHY register at offset and stores the retrieved information
+ * in data. Assumes semaphore already acquired and page already set.
+ **/
+s32 e1000_read_phy_reg_page_hv(struct e1000_hw *hw, u32 offset, u16 *data)
+{
+ return __e1000_read_phy_reg_hv(hw, offset, data, true, true);
}
/**
@@ -2886,11 +2977,12 @@ s32 e1000_read_phy_reg_hv_locked(struct e1000_hw *hw, u32 offset, u16 *data)
* at the offset. Release any acquired semaphores before exiting.
**/
static s32 __e1000_write_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 data,
- bool locked)
+ bool locked, bool page_set)
{
s32 ret_val;
u16 page = BM_PHY_REG_PAGE(offset);
u16 reg = BM_PHY_REG_NUM(offset);
+ u32 phy_addr = hw->phy.addr = e1000_get_phy_addr_for_hv_page(page);
if (!locked) {
ret_val = hw->phy.ops.acquire(hw);
@@ -2900,8 +2992,8 @@ static s32 __e1000_write_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 data,
/* Page 800 works differently than the rest so it has its own func */
if (page == BM_WUC_PAGE) {
- ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset,
- &data, false);
+ ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset, &data,
+ false, page_set);
goto out;
}
@@ -2911,42 +3003,41 @@ static s32 __e1000_write_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 data,
goto out;
}
- hw->phy.addr = e1000_get_phy_addr_for_hv_page(page);
-
- if (page == HV_INTC_FC_PAGE_START)
- page = 0;
-
- /*
- * Workaround MDIO accesses being disabled after entering IEEE Power
- * Down (whenever bit 11 of the PHY Control register is set)
- */
- if ((hw->phy.type == e1000_phy_82578) &&
- (hw->phy.revision >= 1) &&
- (hw->phy.addr == 2) &&
- ((MAX_PHY_REG_ADDRESS & reg) == 0) &&
- (data & (1 << 11))) {
- u16 data2 = 0x7EFF;
- ret_val = e1000_access_phy_debug_regs_hv(hw, (1 << 6) | 0x3,
- &data2, false);
- if (ret_val)
- goto out;
- }
+ if (!page_set) {
+ if (page == HV_INTC_FC_PAGE_START)
+ page = 0;
- if (reg > MAX_PHY_MULTI_PAGE_REG) {
- u32 phy_addr = hw->phy.addr;
+ /*
+ * Workaround MDIO accesses being disabled after entering IEEE
+ * Power Down (when bit 11 of the PHY Control register is set)
+ */
+ if ((hw->phy.type == e1000_phy_82578) &&
+ (hw->phy.revision >= 1) &&
+ (hw->phy.addr == 2) &&
+ ((MAX_PHY_REG_ADDRESS & reg) == 0) && (data & (1 << 11))) {
+ u16 data2 = 0x7EFF;
+ ret_val = e1000_access_phy_debug_regs_hv(hw,
+ (1 << 6) | 0x3,
+ &data2, false);
+ if (ret_val)
+ goto out;
+ }
- hw->phy.addr = 1;
+ if (reg > MAX_PHY_MULTI_PAGE_REG) {
+ /* Page is shifted left, PHY expects (page x 32) */
+ ret_val = e1000_set_page_igp(hw,
+ (page << IGP_PAGE_SHIFT));
- /* Page is shifted left, PHY expects (page x 32) */
- ret_val = e1000e_write_phy_reg_mdic(hw,
- IGP01E1000_PHY_PAGE_SELECT,
- (page << IGP_PAGE_SHIFT));
- hw->phy.addr = phy_addr;
+ hw->phy.addr = phy_addr;
- if (ret_val)
- goto out;
+ if (ret_val)
+ goto out;
+ }
}
+ e_dbg("writing PHY page %d (or 0x%x shifted) reg 0x%x\n", page,
+ page << IGP_PAGE_SHIFT, reg);
+
ret_val = e1000e_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & reg,
data);
@@ -2968,7 +3059,7 @@ out:
**/
s32 e1000_write_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 data)
{
- return __e1000_write_phy_reg_hv(hw, offset, data, false);
+ return __e1000_write_phy_reg_hv(hw, offset, data, false, false);
}
/**
@@ -2982,7 +3073,21 @@ s32 e1000_write_phy_reg_hv(struct e1000_hw *hw, u32 offset, u16 data)
**/
s32 e1000_write_phy_reg_hv_locked(struct e1000_hw *hw, u32 offset, u16 data)
{
- return __e1000_write_phy_reg_hv(hw, offset, data, true);
+ return __e1000_write_phy_reg_hv(hw, offset, data, true, false);
+}
+
+/**
+ * e1000_write_phy_reg_page_hv - Write HV PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Writes the data to PHY register at the offset. Assumes semaphore
+ * already acquired and page already set.
+ **/
+s32 e1000_write_phy_reg_page_hv(struct e1000_hw *hw, u32 offset, u16 data)
+{
+ return __e1000_write_phy_reg_hv(hw, offset, data, true, true);
}
/**
@@ -3004,11 +3109,12 @@ static u32 e1000_get_phy_addr_for_hv_page(u32 page)
* @hw: pointer to the HW structure
* @offset: register offset to be read or written
* @data: pointer to the data to be read or written
- * @read: determines if operation is read or written
+ * @read: determines if operation is read or write
*
* Reads the PHY register at offset and stores the retreived information
* in data. Assumes semaphore already acquired. Note that the procedure
- * to read these regs uses the address port and data port to read/write.
+ * to access these regs uses the address port and data port to read/write.
+ * These accesses done with PHY address 2 and without using pages.
**/
static s32 e1000_access_phy_debug_regs_hv(struct e1000_hw *hw, u32 offset,
u16 *data, bool read)
@@ -3028,7 +3134,7 @@ static s32 e1000_access_phy_debug_regs_hv(struct e1000_hw *hw, u32 offset,
/* masking with 0x3F to remove the page from offset */
ret_val = e1000e_write_phy_reg_mdic(hw, addr_reg, (u16)offset & 0x3F);
if (ret_val) {
- e_dbg("Could not write PHY the HV address register\n");
+ e_dbg("Could not write the Address Offset port register\n");
goto out;
}
@@ -3039,7 +3145,7 @@ static s32 e1000_access_phy_debug_regs_hv(struct e1000_hw *hw, u32 offset,
ret_val = e1000e_write_phy_reg_mdic(hw, data_reg, *data);
if (ret_val) {
- e_dbg("Could not read data value from HV data register\n");
+ e_dbg("Could not access the Data port register\n");
goto out;
}
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-12-23 22:30:35 +0000