diff options
Diffstat (limited to 'drivers/net/ethernet/intel/e1000e/defines.h')
| -rw-r--r-- | drivers/net/ethernet/intel/e1000e/defines.h | 36 |
1 files changed, 18 insertions, 18 deletions
diff --git a/drivers/net/ethernet/intel/e1000e/defines.h b/drivers/net/ethernet/intel/e1000e/defines.h index 76edbc1be33..4dab6fc265a 100644 --- a/drivers/net/ethernet/intel/e1000e/defines.h +++ b/drivers/net/ethernet/intel/e1000e/defines.h @@ -185,8 +185,7 @@ #define E1000_RCTL_BSEX 0x02000000 /* Buffer size extension */ #define E1000_RCTL_SECRC 0x04000000 /* Strip Ethernet CRC */ -/* - * Use byte values for the following shift parameters +/* Use byte values for the following shift parameters * Usage: * psrctl |= (((ROUNDUP(value0, 128) >> E1000_PSRCTL_BSIZE0_SHIFT) & * E1000_PSRCTL_BSIZE0_MASK) | @@ -233,6 +232,7 @@ #define E1000_CTRL_FRCDPX 0x00001000 /* Force Duplex */ #define E1000_CTRL_LANPHYPC_OVERRIDE 0x00010000 /* SW control of LANPHYPC */ #define E1000_CTRL_LANPHYPC_VALUE 0x00020000 /* SW value of LANPHYPC */ +#define E1000_CTRL_MEHE 0x00080000 /* Memory Error Handling Enable */ #define E1000_CTRL_SWDPIN0 0x00040000 /* SWDPIN 0 value */ #define E1000_CTRL_SWDPIN1 0x00080000 /* SWDPIN 1 value */ #define E1000_CTRL_SWDPIO0 0x00400000 /* SWDPIN 0 Input or output */ @@ -242,8 +242,7 @@ #define E1000_CTRL_VME 0x40000000 /* IEEE VLAN mode enable */ #define E1000_CTRL_PHY_RST 0x80000000 /* PHY Reset */ -/* - * Bit definitions for the Management Data IO (MDIO) and Management Data +/* Bit definitions for the Management Data IO (MDIO) and Management Data * Clock (MDC) pins in the Device Control Register. */ @@ -391,6 +390,12 @@ #define E1000_PBS_16K E1000_PBA_16K +/* Uncorrectable/correctable ECC Error counts and enable bits */ +#define E1000_PBECCSTS_CORR_ERR_CNT_MASK 0x000000FF +#define E1000_PBECCSTS_UNCORR_ERR_CNT_MASK 0x0000FF00 +#define E1000_PBECCSTS_UNCORR_ERR_CNT_SHIFT 8 +#define E1000_PBECCSTS_ECC_ENABLE 0x00010000 + #define IFS_MAX 80 #define IFS_MIN 40 #define IFS_RATIO 4 @@ -410,6 +415,7 @@ #define E1000_ICR_RXSEQ 0x00000008 /* Rx sequence error */ #define E1000_ICR_RXDMT0 0x00000010 /* Rx desc min. threshold (0) */ #define E1000_ICR_RXT0 0x00000080 /* Rx timer intr (ring 0) */ +#define E1000_ICR_ECCER 0x00400000 /* Uncorrectable ECC Error */ #define E1000_ICR_INT_ASSERTED 0x80000000 /* If this bit asserted, the driver should claim the interrupt */ #define E1000_ICR_RXQ0 0x00100000 /* Rx Queue 0 Interrupt */ #define E1000_ICR_RXQ1 0x00200000 /* Rx Queue 1 Interrupt */ @@ -424,8 +430,7 @@ #define E1000_PBA_ECC_STAT_CLR 0x00000002 /* Clear ECC error counter */ #define E1000_PBA_ECC_INT_EN 0x00000004 /* Enable ICR bit 5 for ECC */ -/* - * This defines the bits that are set in the Interrupt Mask +/* This defines the bits that are set in the Interrupt Mask * Set/Read Register. Each bit is documented below: * o RXT0 = Receiver Timer Interrupt (ring 0) * o TXDW = Transmit Descriptor Written Back @@ -446,6 +451,7 @@ #define E1000_IMS_RXSEQ E1000_ICR_RXSEQ /* Rx sequence error */ #define E1000_IMS_RXDMT0 E1000_ICR_RXDMT0 /* Rx desc min. threshold */ #define E1000_IMS_RXT0 E1000_ICR_RXT0 /* Rx timer intr */ +#define E1000_IMS_ECCER E1000_ICR_ECCER /* Uncorrectable ECC Error */ #define E1000_IMS_RXQ0 E1000_ICR_RXQ0 /* Rx Queue 0 Interrupt */ #define E1000_IMS_RXQ1 E1000_ICR_RXQ1 /* Rx Queue 1 Interrupt */ #define E1000_IMS_TXQ0 E1000_ICR_TXQ0 /* Tx Queue 0 Interrupt */ @@ -475,8 +481,7 @@ /* 802.1q VLAN Packet Size */ #define E1000_VLAN_FILTER_TBL_SIZE 128 /* VLAN Filter Table (4096 bits) */ -/* Receive Address */ -/* +/* Receive Address * Number of high/low register pairs in the RAR. The RAR (Receive Address * Registers) holds the directed and multicast addresses that we monitor. * Technically, we have 16 spots. However, we reserve one of these spots @@ -723,8 +728,7 @@ #define MAX_PHY_REG_ADDRESS 0x1F /* 5 bit address bus (0-0x1F) */ #define MAX_PHY_MULTI_PAGE_REG 0xF -/* Bit definitions for valid PHY IDs. */ -/* +/* Bit definitions for valid PHY IDs. * I = Integrated * E = External */ @@ -762,8 +766,7 @@ #define M88E1000_PSCR_AUTO_X_1000T 0x0040 /* Auto crossover enabled all speeds */ #define M88E1000_PSCR_AUTO_X_MODE 0x0060 -/* - * 1=Enable Extended 10BASE-T distance (Lower 10BASE-T Rx Threshold) +/* 1=Enable Extended 10BASE-T distance (Lower 10BASE-T Rx Threshold) * 0=Normal 10BASE-T Rx Threshold */ #define M88E1000_PSCR_ASSERT_CRS_ON_TX 0x0800 /* 1=Assert CRS on Transmit */ @@ -779,14 +782,12 @@ #define M88E1000_PSSR_CABLE_LENGTH_SHIFT 7 -/* - * Number of times we will attempt to autonegotiate before downshifting if we +/* Number of times we will attempt to autonegotiate before downshifting if we * are the master */ #define M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK 0x0C00 #define M88E1000_EPSCR_MASTER_DOWNSHIFT_1X 0x0000 -/* - * Number of times we will attempt to autonegotiate before downshifting if we +/* Number of times we will attempt to autonegotiate before downshifting if we * are the slave */ #define M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK 0x0300 @@ -808,8 +809,7 @@ #define PHY_REG(page, reg) (((page) << PHY_PAGE_SHIFT) | \ ((reg) & MAX_PHY_REG_ADDRESS)) -/* - * Bits... +/* Bits... * 15-5: page * 4-0: register offset */ |