diff options
Diffstat (limited to 'drivers/net/ethernet/intel/e1000e/mac.c')
| -rw-r--r-- | drivers/net/ethernet/intel/e1000e/mac.c | 135 |
1 files changed, 45 insertions, 90 deletions
diff --git a/drivers/net/ethernet/intel/e1000e/mac.c b/drivers/net/ethernet/intel/e1000e/mac.c index a1343992848..54d9dafaf12 100644 --- a/drivers/net/ethernet/intel/e1000e/mac.c +++ b/drivers/net/ethernet/intel/e1000e/mac.c @@ -73,8 +73,7 @@ void e1000_set_lan_id_multi_port_pcie(struct e1000_hw *hw) struct e1000_bus_info *bus = &hw->bus; u32 reg; - /* - * The status register reports the correct function number + /* The status register reports the correct function number * for the device regardless of function swap state. */ reg = er32(STATUS); @@ -210,8 +209,7 @@ s32 e1000_check_alt_mac_addr_generic(struct e1000_hw *hw) return 0; } - /* - * We have a valid alternate MAC address, and we want to treat it the + /* We have a valid alternate MAC address, and we want to treat it the * same as the normal permanent MAC address stored by the HW into the * RAR. Do this by mapping this address into RAR0. */ @@ -233,8 +231,7 @@ void e1000e_rar_set_generic(struct e1000_hw *hw, u8 *addr, u32 index) { u32 rar_low, rar_high; - /* - * HW expects these in little endian so we reverse the byte order + /* HW expects these in little endian so we reverse the byte order * from network order (big endian) to little endian */ rar_low = ((u32)addr[0] | ((u32)addr[1] << 8) | @@ -246,8 +243,7 @@ void e1000e_rar_set_generic(struct e1000_hw *hw, u8 *addr, u32 index) if (rar_low || rar_high) rar_high |= E1000_RAH_AV; - /* - * Some bridges will combine consecutive 32-bit writes into + /* Some bridges will combine consecutive 32-bit writes into * a single burst write, which will malfunction on some parts. * The flushes avoid this. */ @@ -273,15 +269,13 @@ static u32 e1000_hash_mc_addr(struct e1000_hw *hw, u8 *mc_addr) /* Register count multiplied by bits per register */ hash_mask = (hw->mac.mta_reg_count * 32) - 1; - /* - * For a mc_filter_type of 0, bit_shift is the number of left-shifts + /* For a mc_filter_type of 0, bit_shift is the number of left-shifts * where 0xFF would still fall within the hash mask. */ while (hash_mask >> bit_shift != 0xFF) bit_shift++; - /* - * The portion of the address that is used for the hash table + /* The portion of the address that is used for the hash table * is determined by the mc_filter_type setting. * The algorithm is such that there is a total of 8 bits of shifting. * The bit_shift for a mc_filter_type of 0 represents the number of @@ -423,8 +417,7 @@ s32 e1000e_check_for_copper_link(struct e1000_hw *hw) s32 ret_val; bool link; - /* - * We only want to go out to the PHY registers to see if Auto-Neg + /* We only want to go out to the PHY registers to see if Auto-Neg * has completed and/or if our link status has changed. The * get_link_status flag is set upon receiving a Link Status * Change or Rx Sequence Error interrupt. @@ -432,8 +425,7 @@ s32 e1000e_check_for_copper_link(struct e1000_hw *hw) if (!mac->get_link_status) return 0; - /* - * First we want to see if the MII Status Register reports + /* First we want to see if the MII Status Register reports * link. If so, then we want to get the current speed/duplex * of the PHY. */ @@ -446,28 +438,24 @@ s32 e1000e_check_for_copper_link(struct e1000_hw *hw) mac->get_link_status = false; - /* - * Check if there was DownShift, must be checked + /* Check if there was DownShift, must be checked * immediately after link-up */ e1000e_check_downshift(hw); - /* - * If we are forcing speed/duplex, then we simply return since + /* If we are forcing speed/duplex, then we simply return since * we have already determined whether we have link or not. */ if (!mac->autoneg) return -E1000_ERR_CONFIG; - /* - * Auto-Neg is enabled. Auto Speed Detection takes care + /* Auto-Neg is enabled. Auto Speed Detection takes care * of MAC speed/duplex configuration. So we only need to * configure Collision Distance in the MAC. */ mac->ops.config_collision_dist(hw); - /* - * Configure Flow Control now that Auto-Neg has completed. + /* Configure Flow Control now that Auto-Neg has completed. * First, we need to restore the desired flow control * settings because we may have had to re-autoneg with a * different link partner. @@ -498,8 +486,7 @@ s32 e1000e_check_for_fiber_link(struct e1000_hw *hw) status = er32(STATUS); rxcw = er32(RXCW); - /* - * If we don't have link (auto-negotiation failed or link partner + /* If we don't have link (auto-negotiation failed or link partner * cannot auto-negotiate), the cable is plugged in (we have signal), * and our link partner is not trying to auto-negotiate with us (we * are receiving idles or data), we need to force link up. We also @@ -530,8 +517,7 @@ s32 e1000e_check_for_fiber_link(struct e1000_hw *hw) return ret_val; } } else if ((ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) { - /* - * If we are forcing link and we are receiving /C/ ordered + /* If we are forcing link and we are receiving /C/ ordered * sets, re-enable auto-negotiation in the TXCW register * and disable forced link in the Device Control register * in an attempt to auto-negotiate with our link partner. @@ -565,8 +551,7 @@ s32 e1000e_check_for_serdes_link(struct e1000_hw *hw) status = er32(STATUS); rxcw = er32(RXCW); - /* - * If we don't have link (auto-negotiation failed or link partner + /* If we don't have link (auto-negotiation failed or link partner * cannot auto-negotiate), and our link partner is not trying to * auto-negotiate with us (we are receiving idles or data), * we need to force link up. We also need to give auto-negotiation @@ -595,8 +580,7 @@ s32 e1000e_check_for_serdes_link(struct e1000_hw *hw) return ret_val; } } else if ((ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) { - /* - * If we are forcing link and we are receiving /C/ ordered + /* If we are forcing link and we are receiving /C/ ordered * sets, re-enable auto-negotiation in the TXCW register * and disable forced link in the Device Control register * in an attempt to auto-negotiate with our link partner. @@ -607,8 +591,7 @@ s32 e1000e_check_for_serdes_link(struct e1000_hw *hw) mac->serdes_has_link = true; } else if (!(E1000_TXCW_ANE & er32(TXCW))) { - /* - * If we force link for non-auto-negotiation switch, check + /* If we force link for non-auto-negotiation switch, check * link status based on MAC synchronization for internal * serdes media type. */ @@ -665,8 +648,7 @@ static s32 e1000_set_default_fc_generic(struct e1000_hw *hw) s32 ret_val; u16 nvm_data; - /* - * Read and store word 0x0F of the EEPROM. This word contains bits + /* Read and store word 0x0F of the EEPROM. This word contains bits * that determine the hardware's default PAUSE (flow control) mode, * a bit that determines whether the HW defaults to enabling or * disabling auto-negotiation, and the direction of the @@ -705,15 +687,13 @@ s32 e1000e_setup_link_generic(struct e1000_hw *hw) { s32 ret_val; - /* - * In the case of the phy reset being blocked, we already have a link. + /* In the case of the phy reset being blocked, we already have a link. * We do not need to set it up again. */ if (hw->phy.ops.check_reset_block && hw->phy.ops.check_reset_block(hw)) return 0; - /* - * If requested flow control is set to default, set flow control + /* If requested flow control is set to default, set flow control * based on the EEPROM flow control settings. */ if (hw->fc.requested_mode == e1000_fc_default) { @@ -722,8 +702,7 @@ s32 e1000e_setup_link_generic(struct e1000_hw *hw) return ret_val; } - /* - * Save off the requested flow control mode for use later. Depending + /* Save off the requested flow control mode for use later. Depending * on the link partner's capabilities, we may or may not use this mode. */ hw->fc.current_mode = hw->fc.requested_mode; @@ -735,8 +714,7 @@ s32 e1000e_setup_link_generic(struct e1000_hw *hw) if (ret_val) return ret_val; - /* - * Initialize the flow control address, type, and PAUSE timer + /* Initialize the flow control address, type, and PAUSE timer * registers to their default values. This is done even if flow * control is disabled, because it does not hurt anything to * initialize these registers. @@ -763,8 +741,7 @@ static s32 e1000_commit_fc_settings_generic(struct e1000_hw *hw) struct e1000_mac_info *mac = &hw->mac; u32 txcw; - /* - * Check for a software override of the flow control settings, and + /* Check for a software override of the flow control settings, and * setup the device accordingly. If auto-negotiation is enabled, then * software will have to set the "PAUSE" bits to the correct value in * the Transmit Config Word Register (TXCW) and re-start auto- @@ -786,8 +763,7 @@ static s32 e1000_commit_fc_settings_generic(struct e1000_hw *hw) txcw = (E1000_TXCW_ANE | E1000_TXCW_FD); break; case e1000_fc_rx_pause: - /* - * Rx Flow control is enabled and Tx Flow control is disabled + /* Rx Flow control is enabled and Tx Flow control is disabled * by a software over-ride. Since there really isn't a way to * advertise that we are capable of Rx Pause ONLY, we will * advertise that we support both symmetric and asymmetric Rx @@ -797,15 +773,13 @@ static s32 e1000_commit_fc_settings_generic(struct e1000_hw *hw) txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK); break; case e1000_fc_tx_pause: - /* - * Tx Flow control is enabled, and Rx Flow control is disabled, + /* Tx Flow control is enabled, and Rx Flow control is disabled, * by a software over-ride. */ txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_ASM_DIR); break; case e1000_fc_full: - /* - * Flow control (both Rx and Tx) is enabled by a software + /* Flow control (both Rx and Tx) is enabled by a software * over-ride. */ txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK); @@ -835,8 +809,7 @@ static s32 e1000_poll_fiber_serdes_link_generic(struct e1000_hw *hw) u32 i, status; s32 ret_val; - /* - * If we have a signal (the cable is plugged in, or assumed true for + /* If we have a signal (the cable is plugged in, or assumed true for * serdes media) then poll for a "Link-Up" indication in the Device * Status Register. Time-out if a link isn't seen in 500 milliseconds * seconds (Auto-negotiation should complete in less than 500 @@ -851,8 +824,7 @@ static s32 e1000_poll_fiber_serdes_link_generic(struct e1000_hw *hw) if (i == FIBER_LINK_UP_LIMIT) { e_dbg("Never got a valid link from auto-neg!!!\n"); mac->autoneg_failed = true; - /* - * AutoNeg failed to achieve a link, so we'll call + /* AutoNeg failed to achieve a link, so we'll call * mac->check_for_link. This routine will force the * link up if we detect a signal. This will allow us to * communicate with non-autonegotiating link partners. @@ -894,8 +866,7 @@ s32 e1000e_setup_fiber_serdes_link(struct e1000_hw *hw) if (ret_val) return ret_val; - /* - * Since auto-negotiation is enabled, take the link out of reset (the + /* Since auto-negotiation is enabled, take the link out of reset (the * link will be in reset, because we previously reset the chip). This * will restart auto-negotiation. If auto-negotiation is successful * then the link-up status bit will be set and the flow control enable @@ -907,8 +878,7 @@ s32 e1000e_setup_fiber_serdes_link(struct e1000_hw *hw) e1e_flush(); usleep_range(1000, 2000); - /* - * For these adapters, the SW definable pin 1 is set when the optics + /* For these adapters, the SW definable pin 1 is set when the optics * detect a signal. If we have a signal, then poll for a "Link-Up" * indication. */ @@ -954,16 +924,14 @@ s32 e1000e_set_fc_watermarks(struct e1000_hw *hw) { u32 fcrtl = 0, fcrth = 0; - /* - * Set the flow control receive threshold registers. Normally, + /* Set the flow control receive threshold registers. Normally, * these registers will be set to a default threshold that may be * adjusted later by the driver's runtime code. However, if the * ability to transmit pause frames is not enabled, then these * registers will be set to 0. */ if (hw->fc.current_mode & e1000_fc_tx_pause) { - /* - * We need to set up the Receive Threshold high and low water + /* We need to set up the Receive Threshold high and low water * marks as well as (optionally) enabling the transmission of * XON frames. */ @@ -995,8 +963,7 @@ s32 e1000e_force_mac_fc(struct e1000_hw *hw) ctrl = er32(CTRL); - /* - * Because we didn't get link via the internal auto-negotiation + /* Because we didn't get link via the internal auto-negotiation * mechanism (we either forced link or we got link via PHY * auto-neg), we have to manually enable/disable transmit an * receive flow control. @@ -1057,8 +1024,7 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw) u16 mii_status_reg, mii_nway_adv_reg, mii_nway_lp_ability_reg; u16 speed, duplex; - /* - * Check for the case where we have fiber media and auto-neg failed + /* Check for the case where we have fiber media and auto-neg failed * so we had to force link. In this case, we need to force the * configuration of the MAC to match the "fc" parameter. */ @@ -1076,15 +1042,13 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw) return ret_val; } - /* - * Check for the case where we have copper media and auto-neg is + /* Check for the case where we have copper media and auto-neg is * enabled. In this case, we need to check and see if Auto-Neg * has completed, and if so, how the PHY and link partner has * flow control configured. */ if ((hw->phy.media_type == e1000_media_type_copper) && mac->autoneg) { - /* - * Read the MII Status Register and check to see if AutoNeg + /* Read the MII Status Register and check to see if AutoNeg * has completed. We read this twice because this reg has * some "sticky" (latched) bits. */ @@ -1100,8 +1064,7 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw) return ret_val; } - /* - * The AutoNeg process has completed, so we now need to + /* The AutoNeg process has completed, so we now need to * read both the Auto Negotiation Advertisement * Register (Address 4) and the Auto_Negotiation Base * Page Ability Register (Address 5) to determine how @@ -1115,8 +1078,7 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw) if (ret_val) return ret_val; - /* - * Two bits in the Auto Negotiation Advertisement Register + /* Two bits in the Auto Negotiation Advertisement Register * (Address 4) and two bits in the Auto Negotiation Base * Page Ability Register (Address 5) determine flow control * for both the PHY and the link partner. The following @@ -1151,8 +1113,7 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw) */ if ((mii_nway_adv_reg & NWAY_AR_PAUSE) && (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) { - /* - * Now we need to check if the user selected Rx ONLY + /* Now we need to check if the user selected Rx ONLY * of pause frames. In this case, we had to advertise * FULL flow control because we could not advertise Rx * ONLY. Hence, we must now check to see if we need to @@ -1166,8 +1127,7 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw) e_dbg("Flow Control = Rx PAUSE frames only.\n"); } } - /* - * For receiving PAUSE frames ONLY. + /* For receiving PAUSE frames ONLY. * * LOCAL DEVICE | LINK PARTNER * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result @@ -1181,8 +1141,7 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw) hw->fc.current_mode = e1000_fc_tx_pause; e_dbg("Flow Control = Tx PAUSE frames only.\n"); } - /* - * For transmitting PAUSE frames ONLY. + /* For transmitting PAUSE frames ONLY. * * LOCAL DEVICE | LINK PARTNER * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result @@ -1196,16 +1155,14 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw) hw->fc.current_mode = e1000_fc_rx_pause; e_dbg("Flow Control = Rx PAUSE frames only.\n"); } else { - /* - * Per the IEEE spec, at this point flow control + /* Per the IEEE spec, at this point flow control * should be disabled. */ hw->fc.current_mode = e1000_fc_none; e_dbg("Flow Control = NONE.\n"); } - /* - * Now we need to do one last check... If we auto- + /* Now we need to do one last check... If we auto- * negotiated to HALF DUPLEX, flow control should not be * enabled per IEEE 802.3 spec. */ @@ -1218,8 +1175,7 @@ s32 e1000e_config_fc_after_link_up(struct e1000_hw *hw) if (duplex == HALF_DUPLEX) hw->fc.current_mode = e1000_fc_none; - /* - * Now we call a subroutine to actually force the MAC + /* Now we call a subroutine to actually force the MAC * controller to use the correct flow control settings. */ ret_val = e1000e_force_mac_fc(hw); @@ -1520,8 +1476,7 @@ s32 e1000e_blink_led_generic(struct e1000_hw *hw) ledctl_blink = E1000_LEDCTL_LED0_BLINK | (E1000_LEDCTL_MODE_LED_ON << E1000_LEDCTL_LED0_MODE_SHIFT); } else { - /* - * set the blink bit for each LED that's "on" (0x0E) + /* set the blink bit for each LED that's "on" (0x0E) * in ledctl_mode2 */ ledctl_blink = hw->mac.ledctl_mode2; |