diff options
Diffstat (limited to 'drivers/net/ethernet/intel')
| -rw-r--r-- | drivers/net/ethernet/intel/igb/e1000_82575.c | 43 | ||||
| -rw-r--r-- | drivers/net/ethernet/intel/igb/e1000_defines.h | 7 | ||||
| -rw-r--r-- | drivers/net/ethernet/intel/igb/e1000_mac.c | 124 |
3 files changed, 166 insertions, 8 deletions
diff --git a/drivers/net/ethernet/intel/igb/e1000_82575.c b/drivers/net/ethernet/intel/igb/e1000_82575.c index db40b68819d..fdaaf2709d0 100644 --- a/drivers/net/ethernet/intel/igb/e1000_82575.c +++ b/drivers/net/ethernet/intel/igb/e1000_82575.c @@ -1028,6 +1028,15 @@ static s32 igb_check_for_link_82575(struct e1000_hw *hw) * continue to check for link. */ hw->mac.get_link_status = !hw->mac.serdes_has_link; + + /* Configure Flow Control now that Auto-Neg has completed. + * First, we need to restore the desired flow control + * settings because we may have had to re-autoneg with a + * different link partner. + */ + ret_val = igb_config_fc_after_link_up(hw); + if (ret_val) + hw_dbg("Error configuring flow control\n"); } else { ret_val = igb_check_for_copper_link(hw); } @@ -1345,7 +1354,7 @@ out: **/ static s32 igb_setup_serdes_link_82575(struct e1000_hw *hw) { - u32 ctrl_ext, ctrl_reg, reg; + u32 ctrl_ext, ctrl_reg, reg, anadv_reg; bool pcs_autoneg; s32 ret_val = E1000_SUCCESS; u16 data; @@ -1433,27 +1442,45 @@ static s32 igb_setup_serdes_link_82575(struct e1000_hw *hw) reg &= ~(E1000_PCS_LCTL_AN_ENABLE | E1000_PCS_LCTL_FLV_LINK_UP | E1000_PCS_LCTL_FSD | E1000_PCS_LCTL_FORCE_LINK); - /* - * We force flow control to prevent the CTRL register values from being - * overwritten by the autonegotiated flow control values - */ - reg |= E1000_PCS_LCTL_FORCE_FCTRL; - if (pcs_autoneg) { /* Set PCS register for autoneg */ reg |= E1000_PCS_LCTL_AN_ENABLE | /* Enable Autoneg */ E1000_PCS_LCTL_AN_RESTART; /* Restart autoneg */ + + /* Disable force flow control for autoneg */ + reg &= ~E1000_PCS_LCTL_FORCE_FCTRL; + + /* Configure flow control advertisement for autoneg */ + anadv_reg = rd32(E1000_PCS_ANADV); + anadv_reg &= ~(E1000_TXCW_ASM_DIR | E1000_TXCW_PAUSE); + switch (hw->fc.requested_mode) { + case e1000_fc_full: + case e1000_fc_rx_pause: + anadv_reg |= E1000_TXCW_ASM_DIR; + anadv_reg |= E1000_TXCW_PAUSE; + break; + case e1000_fc_tx_pause: + anadv_reg |= E1000_TXCW_ASM_DIR; + break; + default: + break; + } + wr32(E1000_PCS_ANADV, anadv_reg); + hw_dbg("Configuring Autoneg:PCS_LCTL=0x%08X\n", reg); } else { /* Set PCS register for forced link */ reg |= E1000_PCS_LCTL_FSD; /* Force Speed */ + /* Force flow control for forced link */ + reg |= E1000_PCS_LCTL_FORCE_FCTRL; + hw_dbg("Configuring Forced Link:PCS_LCTL=0x%08X\n", reg); } wr32(E1000_PCS_LCTL, reg); - if (!igb_sgmii_active_82575(hw)) + if (!pcs_autoneg && !igb_sgmii_active_82575(hw)) igb_force_mac_fc(hw); return ret_val; diff --git a/drivers/net/ethernet/intel/igb/e1000_defines.h b/drivers/net/ethernet/intel/igb/e1000_defines.h index 198d1484882..45dce06eff2 100644 --- a/drivers/net/ethernet/intel/igb/e1000_defines.h +++ b/drivers/net/ethernet/intel/igb/e1000_defines.h @@ -431,6 +431,10 @@ #define FLOW_CONTROL_ADDRESS_HIGH 0x00000100 #define FLOW_CONTROL_TYPE 0x8808 +/* Transmit Config Word */ +#define E1000_TXCW_ASM_DIR 0x00000100 /* TXCW astm pause direction */ +#define E1000_TXCW_PAUSE 0x00000080 /* TXCW sym pause request */ + /* 802.1q VLAN Packet Size */ #define VLAN_TAG_SIZE 4 /* 802.3ac tag (not DMA'd) */ #define E1000_VLAN_FILTER_TBL_SIZE 128 /* VLAN Filter Table (4096 bits) */ @@ -539,6 +543,9 @@ /* mPHY Near End Digital Loopback Override Bit */ #define E1000_MPHY_PCS_CLK_REG_DIGINELBEN 0x10 +#define E1000_PCS_LCTL_FORCE_FCTRL 0x80 +#define E1000_PCS_LSTS_AN_COMPLETE 0x10000 + /* PHY Control Register */ #define MII_CR_FULL_DUPLEX 0x0100 /* FDX =1, half duplex =0 */ #define MII_CR_RESTART_AUTO_NEG 0x0200 /* Restart auto negotiation */ diff --git a/drivers/net/ethernet/intel/igb/e1000_mac.c b/drivers/net/ethernet/intel/igb/e1000_mac.c index 7acddfe9e6d..101e6e4da97 100644 --- a/drivers/net/ethernet/intel/igb/e1000_mac.c +++ b/drivers/net/ethernet/intel/igb/e1000_mac.c @@ -839,6 +839,7 @@ s32 igb_config_fc_after_link_up(struct e1000_hw *hw) { struct e1000_mac_info *mac = &hw->mac; s32 ret_val = 0; + u32 pcs_status_reg, pcs_adv_reg, pcs_lp_ability_reg, pcs_ctrl_reg; u16 mii_status_reg, mii_nway_adv_reg, mii_nway_lp_ability_reg; u16 speed, duplex; @@ -1040,6 +1041,129 @@ s32 igb_config_fc_after_link_up(struct e1000_hw *hw) goto out; } } + /* Check for the case where we have SerDes media and auto-neg is + * enabled. In this case, we need to check and see if Auto-Neg + * has completed, and if so, how the PHY and link partner has + * flow control configured. + */ + if ((hw->phy.media_type == e1000_media_type_internal_serdes) + && mac->autoneg) { + /* Read the PCS_LSTS and check to see if AutoNeg + * has completed. + */ + pcs_status_reg = rd32(E1000_PCS_LSTAT); + + if (!(pcs_status_reg & E1000_PCS_LSTS_AN_COMPLETE)) { + hw_dbg("PCS Auto Neg has not completed.\n"); + return ret_val; + } + + /* The AutoNeg process has completed, so we now need to + * read both the Auto Negotiation Advertisement + * Register (PCS_ANADV) and the Auto_Negotiation Base + * Page Ability Register (PCS_LPAB) to determine how + * flow control was negotiated. + */ + pcs_adv_reg = rd32(E1000_PCS_ANADV); + pcs_lp_ability_reg = rd32(E1000_PCS_LPAB); + + /* Two bits in the Auto Negotiation Advertisement Register + * (PCS_ANADV) and two bits in the Auto Negotiation Base + * Page Ability Register (PCS_LPAB) determine flow control + * for both the PHY and the link partner. The following + * table, taken out of the IEEE 802.3ab/D6.0 dated March 25, + * 1999, describes these PAUSE resolution bits and how flow + * control is determined based upon these settings. + * NOTE: DC = Don't Care + * + * LOCAL DEVICE | LINK PARTNER + * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution + *-------|---------|-------|---------|-------------------- + * 0 | 0 | DC | DC | e1000_fc_none + * 0 | 1 | 0 | DC | e1000_fc_none + * 0 | 1 | 1 | 0 | e1000_fc_none + * 0 | 1 | 1 | 1 | e1000_fc_tx_pause + * 1 | 0 | 0 | DC | e1000_fc_none + * 1 | DC | 1 | DC | e1000_fc_full + * 1 | 1 | 0 | 0 | e1000_fc_none + * 1 | 1 | 0 | 1 | e1000_fc_rx_pause + * + * Are both PAUSE bits set to 1? If so, this implies + * Symmetric Flow Control is enabled at both ends. The + * ASM_DIR bits are irrelevant per the spec. + * + * For Symmetric Flow Control: + * + * LOCAL DEVICE | LINK PARTNER + * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result + *-------|---------|-------|---------|-------------------- + * 1 | DC | 1 | DC | e1000_fc_full + * + */ + if ((pcs_adv_reg & E1000_TXCW_PAUSE) && + (pcs_lp_ability_reg & E1000_TXCW_PAUSE)) { + /* Now we need to check if the user selected Rx ONLY + * of pause frames. In this case, we had to advertise + * FULL flow control because we could not advertise Rx + * ONLY. Hence, we must now check to see if we need to + * turn OFF the TRANSMISSION of PAUSE frames. + */ + if (hw->fc.requested_mode == e1000_fc_full) { + hw->fc.current_mode = e1000_fc_full; + hw_dbg("Flow Control = FULL.\n"); + } else { + hw->fc.current_mode = e1000_fc_rx_pause; + hw_dbg("Flow Control = Rx PAUSE frames only.\n"); + } + } + /* For receiving PAUSE frames ONLY. + * + * LOCAL DEVICE | LINK PARTNER + * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result + *-------|---------|-------|---------|-------------------- + * 0 | 1 | 1 | 1 | e1000_fc_tx_pause + */ + else if (!(pcs_adv_reg & E1000_TXCW_PAUSE) && + (pcs_adv_reg & E1000_TXCW_ASM_DIR) && + (pcs_lp_ability_reg & E1000_TXCW_PAUSE) && + (pcs_lp_ability_reg & E1000_TXCW_ASM_DIR)) { + hw->fc.current_mode = e1000_fc_tx_pause; + hw_dbg("Flow Control = Tx PAUSE frames only.\n"); + } + /* For transmitting PAUSE frames ONLY. + * + * LOCAL DEVICE | LINK PARTNER + * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result + *-------|---------|-------|---------|-------------------- + * 1 | 1 | 0 | 1 | e1000_fc_rx_pause + */ + else if ((pcs_adv_reg & E1000_TXCW_PAUSE) && + (pcs_adv_reg & E1000_TXCW_ASM_DIR) && + !(pcs_lp_ability_reg & E1000_TXCW_PAUSE) && + (pcs_lp_ability_reg & E1000_TXCW_ASM_DIR)) { + hw->fc.current_mode = e1000_fc_rx_pause; + hw_dbg("Flow Control = Rx PAUSE frames only.\n"); + } else { + /* Per the IEEE spec, at this point flow control + * should be disabled. + */ + hw->fc.current_mode = e1000_fc_none; + hw_dbg("Flow Control = NONE.\n"); + } + + /* Now we call a subroutine to actually force the MAC + * controller to use the correct flow control settings. + */ + pcs_ctrl_reg = rd32(E1000_PCS_LCTL); + pcs_ctrl_reg |= E1000_PCS_LCTL_FORCE_FCTRL; + wr32(E1000_PCS_LCTL, pcs_ctrl_reg); + + ret_val = igb_force_mac_fc(hw); + if (ret_val) { + hw_dbg("Error forcing flow control settings\n"); + return ret_val; + } + } out: return ret_val; |