diff options
Diffstat (limited to 'drivers/net/ethernet/marvell/sky2.c')
| -rw-r--r-- | drivers/net/ethernet/marvell/sky2.c | 5130 |
1 files changed, 5130 insertions, 0 deletions
diff --git a/drivers/net/ethernet/marvell/sky2.c b/drivers/net/ethernet/marvell/sky2.c new file mode 100644 index 00000000000..57339da7632 --- /dev/null +++ b/drivers/net/ethernet/marvell/sky2.c @@ -0,0 +1,5130 @@ +/* + * New driver for Marvell Yukon 2 chipset. + * Based on earlier sk98lin, and skge driver. + * + * This driver intentionally does not support all the features + * of the original driver such as link fail-over and link management because + * those should be done at higher levels. + * + * Copyright (C) 2005 Stephen Hemminger <shemminger@osdl.org> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + +#include <linux/crc32.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/netdevice.h> +#include <linux/dma-mapping.h> +#include <linux/etherdevice.h> +#include <linux/ethtool.h> +#include <linux/pci.h> +#include <linux/interrupt.h> +#include <linux/ip.h> +#include <linux/slab.h> +#include <net/ip.h> +#include <linux/tcp.h> +#include <linux/in.h> +#include <linux/delay.h> +#include <linux/workqueue.h> +#include <linux/if_vlan.h> +#include <linux/prefetch.h> +#include <linux/debugfs.h> +#include <linux/mii.h> + +#include <asm/irq.h> + +#include "sky2.h" + +#define DRV_NAME "sky2" +#define DRV_VERSION "1.29" + +/* + * The Yukon II chipset takes 64 bit command blocks (called list elements) + * that are organized into three (receive, transmit, status) different rings + * similar to Tigon3. + */ + +#define RX_LE_SIZE 1024 +#define RX_LE_BYTES (RX_LE_SIZE*sizeof(struct sky2_rx_le)) +#define RX_MAX_PENDING (RX_LE_SIZE/6 - 2) +#define RX_DEF_PENDING RX_MAX_PENDING + +/* This is the worst case number of transmit list elements for a single skb: + VLAN:GSO + CKSUM + Data + skb_frags * DMA */ +#define MAX_SKB_TX_LE (2 + (sizeof(dma_addr_t)/sizeof(u32))*(MAX_SKB_FRAGS+1)) +#define TX_MIN_PENDING (MAX_SKB_TX_LE+1) +#define TX_MAX_PENDING 1024 +#define TX_DEF_PENDING 127 + +#define TX_WATCHDOG (5 * HZ) +#define NAPI_WEIGHT 64 +#define PHY_RETRIES 1000 + +#define SKY2_EEPROM_MAGIC 0x9955aabb + +#define RING_NEXT(x, s) (((x)+1) & ((s)-1)) + +static const u32 default_msg = + NETIF_MSG_DRV | NETIF_MSG_PROBE | NETIF_MSG_LINK + | NETIF_MSG_TIMER | NETIF_MSG_TX_ERR | NETIF_MSG_RX_ERR + | NETIF_MSG_IFUP | NETIF_MSG_IFDOWN; + +static int debug = -1; /* defaults above */ +module_param(debug, int, 0); +MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)"); + +static int copybreak __read_mostly = 128; +module_param(copybreak, int, 0); +MODULE_PARM_DESC(copybreak, "Receive copy threshold"); + +static int disable_msi = 0; +module_param(disable_msi, int, 0); +MODULE_PARM_DESC(disable_msi, "Disable Message Signaled Interrupt (MSI)"); + +static DEFINE_PCI_DEVICE_TABLE(sky2_id_table) = { + { PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9000) }, /* SK-9Sxx */ + { PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9E00) }, /* SK-9Exx */ + { PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x9E01) }, /* SK-9E21M */ + { PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4b00) }, /* DGE-560T */ + { PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4001) }, /* DGE-550SX */ + { PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4B02) }, /* DGE-560SX */ + { PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4B03) }, /* DGE-550T */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4340) }, /* 88E8021 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4341) }, /* 88E8022 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4342) }, /* 88E8061 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4343) }, /* 88E8062 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4344) }, /* 88E8021 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4345) }, /* 88E8022 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4346) }, /* 88E8061 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4347) }, /* 88E8062 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4350) }, /* 88E8035 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4351) }, /* 88E8036 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4352) }, /* 88E8038 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4353) }, /* 88E8039 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4354) }, /* 88E8040 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4355) }, /* 88E8040T */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4356) }, /* 88EC033 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4357) }, /* 88E8042 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x435A) }, /* 88E8048 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4360) }, /* 88E8052 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4361) }, /* 88E8050 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4362) }, /* 88E8053 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4363) }, /* 88E8055 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4364) }, /* 88E8056 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4365) }, /* 88E8070 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4366) }, /* 88EC036 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4367) }, /* 88EC032 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4368) }, /* 88EC034 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4369) }, /* 88EC042 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x436A) }, /* 88E8058 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x436B) }, /* 88E8071 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x436C) }, /* 88E8072 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x436D) }, /* 88E8055 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4370) }, /* 88E8075 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4380) }, /* 88E8057 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4381) }, /* 88E8059 */ + { 0 } +}; + +MODULE_DEVICE_TABLE(pci, sky2_id_table); + +/* Avoid conditionals by using array */ +static const unsigned txqaddr[] = { Q_XA1, Q_XA2 }; +static const unsigned rxqaddr[] = { Q_R1, Q_R2 }; +static const u32 portirq_msk[] = { Y2_IS_PORT_1, Y2_IS_PORT_2 }; + +static void sky2_set_multicast(struct net_device *dev); + +/* Access to PHY via serial interconnect */ +static int gm_phy_write(struct sky2_hw *hw, unsigned port, u16 reg, u16 val) +{ + int i; + + gma_write16(hw, port, GM_SMI_DATA, val); + gma_write16(hw, port, GM_SMI_CTRL, + GM_SMI_CT_PHY_AD(PHY_ADDR_MARV) | GM_SMI_CT_REG_AD(reg)); + + for (i = 0; i < PHY_RETRIES; i++) { + u16 ctrl = gma_read16(hw, port, GM_SMI_CTRL); + if (ctrl == 0xffff) + goto io_error; + + if (!(ctrl & GM_SMI_CT_BUSY)) + return 0; + + udelay(10); + } + + dev_warn(&hw->pdev->dev, "%s: phy write timeout\n", hw->dev[port]->name); + return -ETIMEDOUT; + +io_error: + dev_err(&hw->pdev->dev, "%s: phy I/O error\n", hw->dev[port]->name); + return -EIO; +} + +static int __gm_phy_read(struct sky2_hw *hw, unsigned port, u16 reg, u16 *val) +{ + int i; + + gma_write16(hw, port, GM_SMI_CTRL, GM_SMI_CT_PHY_AD(PHY_ADDR_MARV) + | GM_SMI_CT_REG_AD(reg) | GM_SMI_CT_OP_RD); + + for (i = 0; i < PHY_RETRIES; i++) { + u16 ctrl = gma_read16(hw, port, GM_SMI_CTRL); + if (ctrl == 0xffff) + goto io_error; + + if (ctrl & GM_SMI_CT_RD_VAL) { + *val = gma_read16(hw, port, GM_SMI_DATA); + return 0; + } + + udelay(10); + } + + dev_warn(&hw->pdev->dev, "%s: phy read timeout\n", hw->dev[port]->name); + return -ETIMEDOUT; +io_error: + dev_err(&hw->pdev->dev, "%s: phy I/O error\n", hw->dev[port]->name); + return -EIO; +} + +static inline u16 gm_phy_read(struct sky2_hw *hw, unsigned port, u16 reg) +{ + u16 v; + __gm_phy_read(hw, port, reg, &v); + return v; +} + + +static void sky2_power_on(struct sky2_hw *hw) +{ + /* switch power to VCC (WA for VAUX problem) */ + sky2_write8(hw, B0_POWER_CTRL, + PC_VAUX_ENA | PC_VCC_ENA | PC_VAUX_OFF | PC_VCC_ON); + + /* disable Core Clock Division, */ + sky2_write32(hw, B2_Y2_CLK_CTRL, Y2_CLK_DIV_DIS); + + if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > CHIP_REV_YU_XL_A1) + /* enable bits are inverted */ + sky2_write8(hw, B2_Y2_CLK_GATE, + Y2_PCI_CLK_LNK1_DIS | Y2_COR_CLK_LNK1_DIS | + Y2_CLK_GAT_LNK1_DIS | Y2_PCI_CLK_LNK2_DIS | + Y2_COR_CLK_LNK2_DIS | Y2_CLK_GAT_LNK2_DIS); + else + sky2_write8(hw, B2_Y2_CLK_GATE, 0); + + if (hw->flags & SKY2_HW_ADV_POWER_CTL) { + u32 reg; + + sky2_pci_write32(hw, PCI_DEV_REG3, 0); + + reg = sky2_pci_read32(hw, PCI_DEV_REG4); + /* set all bits to 0 except bits 15..12 and 8 */ + reg &= P_ASPM_CONTROL_MSK; + sky2_pci_write32(hw, PCI_DEV_REG4, reg); + + reg = sky2_pci_read32(hw, PCI_DEV_REG5); + /* set all bits to 0 except bits 28 & 27 */ + reg &= P_CTL_TIM_VMAIN_AV_MSK; + sky2_pci_write32(hw, PCI_DEV_REG5, reg); + + sky2_pci_write32(hw, PCI_CFG_REG_1, 0); + + sky2_write16(hw, B0_CTST, Y2_HW_WOL_ON); + + /* Enable workaround for dev 4.107 on Yukon-Ultra & Extreme */ + reg = sky2_read32(hw, B2_GP_IO); + reg |= GLB_GPIO_STAT_RACE_DIS; + sky2_write32(hw, B2_GP_IO, reg); + + sky2_read32(hw, B2_GP_IO); + } + + /* Turn on "driver loaded" LED */ + sky2_write16(hw, B0_CTST, Y2_LED_STAT_ON); +} + +static void sky2_power_aux(struct sky2_hw *hw) +{ + if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > CHIP_REV_YU_XL_A1) + sky2_write8(hw, B2_Y2_CLK_GATE, 0); + else + /* enable bits are inverted */ + sky2_write8(hw, B2_Y2_CLK_GATE, + Y2_PCI_CLK_LNK1_DIS | Y2_COR_CLK_LNK1_DIS | + Y2_CLK_GAT_LNK1_DIS | Y2_PCI_CLK_LNK2_DIS | + Y2_COR_CLK_LNK2_DIS | Y2_CLK_GAT_LNK2_DIS); + + /* switch power to VAUX if supported and PME from D3cold */ + if ( (sky2_read32(hw, B0_CTST) & Y2_VAUX_AVAIL) && + pci_pme_capable(hw->pdev, PCI_D3cold)) + sky2_write8(hw, B0_POWER_CTRL, + (PC_VAUX_ENA | PC_VCC_ENA | + PC_VAUX_ON | PC_VCC_OFF)); + + /* turn off "driver loaded LED" */ + sky2_write16(hw, B0_CTST, Y2_LED_STAT_OFF); +} + +static void sky2_gmac_reset(struct sky2_hw *hw, unsigned port) +{ + u16 reg; + + /* disable all GMAC IRQ's */ + sky2_write8(hw, SK_REG(port, GMAC_IRQ_MSK), 0); + + gma_write16(hw, port, GM_MC_ADDR_H1, 0); /* clear MC hash */ + gma_write16(hw, port, GM_MC_ADDR_H2, 0); + gma_write16(hw, port, GM_MC_ADDR_H3, 0); + gma_write16(hw, port, GM_MC_ADDR_H4, 0); + + reg = gma_read16(hw, port, GM_RX_CTRL); + reg |= GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA; + gma_write16(hw, port, GM_RX_CTRL, reg); +} + +/* flow control to advertise bits */ +static const u16 copper_fc_adv[] = { + [FC_NONE] = 0, + [FC_TX] = PHY_M_AN_ASP, + [FC_RX] = PHY_M_AN_PC, + [FC_BOTH] = PHY_M_AN_PC | PHY_M_AN_ASP, +}; + +/* flow control to advertise bits when using 1000BaseX */ +static const u16 fiber_fc_adv[] = { + [FC_NONE] = PHY_M_P_NO_PAUSE_X, + [FC_TX] = PHY_M_P_ASYM_MD_X, + [FC_RX] = PHY_M_P_SYM_MD_X, + [FC_BOTH] = PHY_M_P_BOTH_MD_X, +}; + +/* flow control to GMA disable bits */ +static const u16 gm_fc_disable[] = { + [FC_NONE] = GM_GPCR_FC_RX_DIS | GM_GPCR_FC_TX_DIS, + [FC_TX] = GM_GPCR_FC_RX_DIS, + [FC_RX] = GM_GPCR_FC_TX_DIS, + [FC_BOTH] = 0, +}; + + +static void sky2_phy_init(struct sky2_hw *hw, unsigned port) +{ + struct sky2_port *sky2 = netdev_priv(hw->dev[port]); + u16 ctrl, ct1000, adv, pg, ledctrl, ledover, reg; + + if ( (sky2->flags & SKY2_FLAG_AUTO_SPEED) && + !(hw->flags & SKY2_HW_NEWER_PHY)) { + u16 ectrl = gm_phy_read(hw, port, PHY_MARV_EXT_CTRL); + + ectrl &= ~(PHY_M_EC_M_DSC_MSK | PHY_M_EC_S_DSC_MSK | + PHY_M_EC_MAC_S_MSK); + ectrl |= PHY_M_EC_MAC_S(MAC_TX_CLK_25_MHZ); + + /* on PHY 88E1040 Rev.D0 (and newer) downshift control changed */ + if (hw->chip_id == CHIP_ID_YUKON_EC) + /* set downshift counter to 3x and enable downshift */ + ectrl |= PHY_M_EC_DSC_2(2) | PHY_M_EC_DOWN_S_ENA; + else + /* set master & slave downshift counter to 1x */ + ectrl |= PHY_M_EC_M_DSC(0) | PHY_M_EC_S_DSC(1); + + gm_phy_write(hw, port, PHY_MARV_EXT_CTRL, ectrl); + } + + ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL); + if (sky2_is_copper(hw)) { + if (!(hw->flags & SKY2_HW_GIGABIT)) { + /* enable automatic crossover */ + ctrl |= PHY_M_PC_MDI_XMODE(PHY_M_PC_ENA_AUTO) >> 1; + + if (hw->chip_id == CHIP_ID_YUKON_FE_P && + hw->chip_rev == CHIP_REV_YU_FE2_A0) { + u16 spec; + + /* Enable Class A driver for FE+ A0 */ + spec = gm_phy_read(hw, port, PHY_MARV_FE_SPEC_2); + spec |= PHY_M_FESC_SEL_CL_A; + gm_phy_write(hw, port, PHY_MARV_FE_SPEC_2, spec); + } + } else { + if (hw->chip_id >= CHIP_ID_YUKON_OPT) { + u16 ctrl2 = gm_phy_read(hw, port, PHY_MARV_EXT_CTRL_2); + + /* enable PHY Reverse Auto-Negotiation */ + ctrl2 |= 1u << 13; + + /* Write PHY changes (SW-reset must follow) */ + gm_phy_write(hw, port, PHY_MARV_EXT_CTRL_2, ctrl2); + } + + + /* disable energy detect */ + ctrl &= ~PHY_M_PC_EN_DET_MSK; + + /* enable automatic crossover */ + ctrl |= PHY_M_PC_MDI_XMODE(PHY_M_PC_ENA_AUTO); + + /* downshift on PHY 88E1112 and 88E1149 is changed */ + if ( (sky2->flags & SKY2_FLAG_AUTO_SPEED) && + (hw->flags & SKY2_HW_NEWER_PHY)) { + /* set downshift counter to 3x and enable downshift */ + ctrl &= ~PHY_M_PC_DSC_MSK; + ctrl |= PHY_M_PC_DSC(2) | PHY_M_PC_DOWN_S_ENA; + } + } + } else { + /* workaround for deviation #4.88 (CRC errors) */ + /* disable Automatic Crossover */ + + ctrl &= ~PHY_M_PC_MDIX_MSK; + } + + gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl); + + /* special setup for PHY 88E1112 Fiber */ + if (hw->chip_id == CHIP_ID_YUKON_XL && (hw->flags & SKY2_HW_FIBRE_PHY)) { + pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR); + + /* Fiber: select 1000BASE-X only mode MAC Specific Ctrl Reg. */ + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 2); + ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL); + ctrl &= ~PHY_M_MAC_MD_MSK; + ctrl |= PHY_M_MAC_MODE_SEL(PHY_M_MAC_MD_1000BX); + gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl); + + if (hw->pmd_type == 'P') { + /* select page 1 to access Fiber registers */ + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 1); + + /* for SFP-module set SIGDET polarity to low */ + ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL); + ctrl |= PHY_M_FIB_SIGD_POL; + gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl); + } + + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg); + } + + ctrl = PHY_CT_RESET; + ct1000 = 0; + adv = PHY_AN_CSMA; + reg = 0; + + if (sky2->flags & SKY2_FLAG_AUTO_SPEED) { + if (sky2_is_copper(hw)) { + if (sky2->advertising & ADVERTISED_1000baseT_Full) + ct1000 |= PHY_M_1000C_AFD; + if (sky2->advertising & ADVERTISED_1000baseT_Half) + ct1000 |= PHY_M_1000C_AHD; + if (sky2->advertising & ADVERTISED_100baseT_Full) + adv |= PHY_M_AN_100_FD; + if (sky2->advertising & ADVERTISED_100baseT_Half) + adv |= PHY_M_AN_100_HD; + if (sky2->advertising & ADVERTISED_10baseT_Full) + adv |= PHY_M_AN_10_FD; + if (sky2->advertising & ADVERTISED_10baseT_Half) + adv |= PHY_M_AN_10_HD; + + } else { /* special defines for FIBER (88E1040S only) */ + if (sky2->advertising & ADVERTISED_1000baseT_Full) + adv |= PHY_M_AN_1000X_AFD; + if (sky2->advertising & ADVERTISED_1000baseT_Half) + adv |= PHY_M_AN_1000X_AHD; + } + + /* Restart Auto-negotiation */ + ctrl |= PHY_CT_ANE | PHY_CT_RE_CFG; + } else { + /* forced speed/duplex settings */ + ct1000 = PHY_M_1000C_MSE; + + /* Disable auto update for duplex flow control and duplex */ + reg |= GM_GPCR_AU_DUP_DIS | GM_GPCR_AU_SPD_DIS; + + switch (sky2->speed) { + case SPEED_1000: + ctrl |= PHY_CT_SP1000; + reg |= GM_GPCR_SPEED_1000; + break; + case SPEED_100: + ctrl |= PHY_CT_SP100; + reg |= GM_GPCR_SPEED_100; + break; + } + + if (sky2->duplex == DUPLEX_FULL) { + reg |= GM_GPCR_DUP_FULL; + ctrl |= PHY_CT_DUP_MD; + } else if (sky2->speed < SPEED_1000) + sky2->flow_mode = FC_NONE; + } + + if (sky2->flags & SKY2_FLAG_AUTO_PAUSE) { + if (sky2_is_copper(hw)) + adv |= copper_fc_adv[sky2->flow_mode]; + else + adv |= fiber_fc_adv[sky2->flow_mode]; + } else { + reg |= GM_GPCR_AU_FCT_DIS; + reg |= gm_fc_disable[sky2->flow_mode]; + + /* Forward pause packets to GMAC? */ + if (sky2->flow_mode & FC_RX) + sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_ON); + else + sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF); + } + + gma_write16(hw, port, GM_GP_CTRL, reg); + + if (hw->flags & SKY2_HW_GIGABIT) + gm_phy_write(hw, port, PHY_MARV_1000T_CTRL, ct1000); + + gm_phy_write(hw, port, PHY_MARV_AUNE_ADV, adv); + gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl); + + /* Setup Phy LED's */ + ledctrl = PHY_M_LED_PULS_DUR(PULS_170MS); + ledover = 0; + + switch (hw->chip_id) { + case CHIP_ID_YUKON_FE: + /* on 88E3082 these bits are at 11..9 (shifted left) */ + ledctrl |= PHY_M_LED_BLINK_RT(BLINK_84MS) << 1; + + ctrl = gm_phy_read(hw, port, PHY_MARV_FE_LED_PAR); + + /* delete ACT LED control bits */ + ctrl &= ~PHY_M_FELP_LED1_MSK; + /* change ACT LED control to blink mode */ + ctrl |= PHY_M_FELP_LED1_CTRL(LED_PAR_CTRL_ACT_BL); + gm_phy_write(hw, port, PHY_MARV_FE_LED_PAR, ctrl); + break; + + case CHIP_ID_YUKON_FE_P: + /* Enable Link Partner Next Page */ + ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL); + ctrl |= PHY_M_PC_ENA_LIP_NP; + + /* disable Energy Detect and enable scrambler */ + ctrl &= ~(PHY_M_PC_ENA_ENE_DT | PHY_M_PC_DIS_SCRAMB); + gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl); + + /* set LED2 -> ACT, LED1 -> LINK, LED0 -> SPEED */ + ctrl = PHY_M_FELP_LED2_CTRL(LED_PAR_CTRL_ACT_BL) | + PHY_M_FELP_LED1_CTRL(LED_PAR_CTRL_LINK) | + PHY_M_FELP_LED0_CTRL(LED_PAR_CTRL_SPEED); + + gm_phy_write(hw, port, PHY_MARV_FE_LED_PAR, ctrl); + break; + + case CHIP_ID_YUKON_XL: + pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR); + + /* select page 3 to access LED control register */ + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3); + + /* set LED Function Control register */ + gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, + (PHY_M_LEDC_LOS_CTRL(1) | /* LINK/ACT */ + PHY_M_LEDC_INIT_CTRL(7) | /* 10 Mbps */ + PHY_M_LEDC_STA1_CTRL(7) | /* 100 Mbps */ + PHY_M_LEDC_STA0_CTRL(7))); /* 1000 Mbps */ + + /* set Polarity Control register */ + gm_phy_write(hw, port, PHY_MARV_PHY_STAT, + (PHY_M_POLC_LS1_P_MIX(4) | + PHY_M_POLC_IS0_P_MIX(4) | + PHY_M_POLC_LOS_CTRL(2) | + PHY_M_POLC_INIT_CTRL(2) | + PHY_M_POLC_STA1_CTRL(2) | + PHY_M_POLC_STA0_CTRL(2))); + + /* restore page register */ + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg); + break; + + case CHIP_ID_YUKON_EC_U: + case CHIP_ID_YUKON_EX: + case CHIP_ID_YUKON_SUPR: + pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR); + + /* select page 3 to access LED control register */ + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3); + + /* set LED Function Control register */ + gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, + (PHY_M_LEDC_LOS_CTRL(1) | /* LINK/ACT */ + PHY_M_LEDC_INIT_CTRL(8) | /* 10 Mbps */ + PHY_M_LEDC_STA1_CTRL(7) | /* 100 Mbps */ + PHY_M_LEDC_STA0_CTRL(7)));/* 1000 Mbps */ + + /* set Blink Rate in LED Timer Control Register */ + gm_phy_write(hw, port, PHY_MARV_INT_MASK, + ledctrl | PHY_M_LED_BLINK_RT(BLINK_84MS)); + /* restore page register */ + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg); + break; + + default: + /* set Tx LED (LED_TX) to blink mode on Rx OR Tx activity */ + ledctrl |= PHY_M_LED_BLINK_RT(BLINK_84MS) | PHY_M_LEDC_TX_CTRL; + + /* turn off the Rx LED (LED_RX) */ + ledover |= PHY_M_LED_MO_RX(MO_LED_OFF); + } + + if (hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_UL_2) { + /* apply fixes in PHY AFE */ + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 255); + + /* increase differential signal amplitude in 10BASE-T */ + gm_phy_write(hw, port, 0x18, 0xaa99); + gm_phy_write(hw, port, 0x17, 0x2011); + + if (hw->chip_id == CHIP_ID_YUKON_EC_U) { + /* fix for IEEE A/B Symmetry failure in 1000BASE-T */ + gm_phy_write(hw, port, 0x18, 0xa204); + gm_phy_write(hw, port, 0x17, 0x2002); + } + + /* set page register to 0 */ + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 0); + } else if (hw->chip_id == CHIP_ID_YUKON_FE_P && + hw->chip_rev == CHIP_REV_YU_FE2_A0) { + /* apply workaround for integrated resistors calibration */ + gm_phy_write(hw, port, PHY_MARV_PAGE_ADDR, 17); + gm_phy_write(hw, port, PHY_MARV_PAGE_DATA, 0x3f60); + } else if (hw->chip_id == CHIP_ID_YUKON_OPT && hw->chip_rev == 0) { + /* apply fixes in PHY AFE */ + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 0x00ff); + + /* apply RDAC termination workaround */ + gm_phy_write(hw, port, 24, 0x2800); + gm_phy_write(hw, port, 23, 0x2001); + + /* set page register back to 0 */ + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 0); + } else if (hw->chip_id != CHIP_ID_YUKON_EX && + hw->chip_id < CHIP_ID_YUKON_SUPR) { + /* no effect on Yukon-XL */ + gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl); + + if (!(sky2->flags & SKY2_FLAG_AUTO_SPEED) || + sky2->speed == SPEED_100) { + /* turn on 100 Mbps LED (LED_LINK100) */ + ledover |= PHY_M_LED_MO_100(MO_LED_ON); + } + + if (ledover) + gm_phy_write(hw, port, PHY_MARV_LED_OVER, ledover); + + } else if (hw->chip_id == CHIP_ID_YUKON_PRM && + (sky2_read8(hw, B2_MAC_CFG) & 0xf) == 0x7) { + int i; + /* This a phy register setup workaround copied from vendor driver. */ + static const struct { + u16 reg, val; + } eee_afe[] = { + { 0x156, 0x58ce }, + { 0x153, 0x99eb }, + { 0x141, 0x8064 }, + /* { 0x155, 0x130b },*/ + { 0x000, 0x0000 }, + { 0x151, 0x8433 }, + { 0x14b, 0x8c44 }, + { 0x14c, 0x0f90 }, + { 0x14f, 0x39aa }, + /* { 0x154, 0x2f39 },*/ + { 0x14d, 0xba33 }, + { 0x144, 0x0048 }, + { 0x152, 0x2010 }, + /* { 0x158, 0x1223 },*/ + { 0x140, 0x4444 }, + { 0x154, 0x2f3b }, + { 0x158, 0xb203 }, + { 0x157, 0x2029 }, + }; + + /* Start Workaround for OptimaEEE Rev.Z0 */ + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 0x00fb); + + gm_phy_write(hw, port, 1, 0x4099); + gm_phy_write(hw, port, 3, 0x1120); + gm_phy_write(hw, port, 11, 0x113c); + gm_phy_write(hw, port, 14, 0x8100); + gm_phy_write(hw, port, 15, 0x112a); + gm_phy_write(hw, port, 17, 0x1008); + + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 0x00fc); + gm_phy_write(hw, port, 1, 0x20b0); + + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 0x00ff); + + for (i = 0; i < ARRAY_SIZE(eee_afe); i++) { + /* apply AFE settings */ + gm_phy_write(hw, port, 17, eee_afe[i].val); + gm_phy_write(hw, port, 16, eee_afe[i].reg | 1u<<13); + } + + /* End Workaround for OptimaEEE */ + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 0); + + /* Enable 10Base-Te (EEE) */ + if (hw->chip_id >= CHIP_ID_YUKON_PRM) { + reg = gm_phy_read(hw, port, PHY_MARV_EXT_CTRL); + gm_phy_write(hw, port, PHY_MARV_EXT_CTRL, + reg | PHY_M_10B_TE_ENABLE); + } + } + + /* Enable phy interrupt on auto-negotiation complete (or link up) */ + if (sky2->flags & SKY2_FLAG_AUTO_SPEED) + gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_IS_AN_COMPL); + else + gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_DEF_MSK); +} + +static const u32 phy_power[] = { PCI_Y2_PHY1_POWD, PCI_Y2_PHY2_POWD }; +static const u32 coma_mode[] = { PCI_Y2_PHY1_COMA, PCI_Y2_PHY2_COMA }; + +static void sky2_phy_power_up(struct sky2_hw *hw, unsigned port) +{ + u32 reg1; + + sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON); + reg1 = sky2_pci_read32(hw, PCI_DEV_REG1); + reg1 &= ~phy_power[port]; + + if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev > CHIP_REV_YU_XL_A1) + reg1 |= coma_mode[port]; + + sky2_pci_write32(hw, PCI_DEV_REG1, reg1); + sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF); + sky2_pci_read32(hw, PCI_DEV_REG1); + + if (hw->chip_id == CHIP_ID_YUKON_FE) + gm_phy_write(hw, port, PHY_MARV_CTRL, PHY_CT_ANE); + else if (hw->flags & SKY2_HW_ADV_POWER_CTL) + sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_CLR); +} + +static void sky2_phy_power_down(struct sky2_hw *hw, unsigned port) +{ + u32 reg1; + u16 ctrl; + + /* release GPHY Control reset */ + sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_CLR); + + /* release GMAC reset */ + sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_CLR); + + if (hw->flags & SKY2_HW_NEWER_PHY) { + /* select page 2 to access MAC control register */ + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 2); + + ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL); + /* allow GMII Power Down */ + ctrl &= ~PHY_M_MAC_GMIF_PUP; + gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl); + + /* set page register back to 0 */ + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 0); + } + + /* setup General Purpose Control Register */ + gma_write16(hw, port, GM_GP_CTRL, + GM_GPCR_FL_PASS | GM_GPCR_SPEED_100 | + GM_GPCR_AU_DUP_DIS | GM_GPCR_AU_FCT_DIS | + GM_GPCR_AU_SPD_DIS); + + if (hw->chip_id != CHIP_ID_YUKON_EC) { + if (hw->chip_id == CHIP_ID_YUKON_EC_U) { + /* select page 2 to access MAC control register */ + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 2); + + ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL); + /* enable Power Down */ + ctrl |= PHY_M_PC_POW_D_ENA; + gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl); + + /* set page register back to 0 */ + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 0); + } + + /* set IEEE compatible Power Down Mode (dev. #4.99) */ + gm_phy_write(hw, port, PHY_MARV_CTRL, PHY_CT_PDOWN); + } + + sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON); + reg1 = sky2_pci_read32(hw, PCI_DEV_REG1); + reg1 |= phy_power[port]; /* set PHY to PowerDown/COMA Mode */ + sky2_pci_write32(hw, PCI_DEV_REG1, reg1); + sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF); +} + +/* configure IPG according to used link speed */ +static void sky2_set_ipg(struct sky2_port *sky2) +{ + u16 reg; + + reg = gma_read16(sky2->hw, sky2->port, GM_SERIAL_MODE); + reg &= ~GM_SMOD_IPG_MSK; + if (sky2->speed > SPEED_100) + reg |= IPG_DATA_VAL(IPG_DATA_DEF_1000); + else + reg |= IPG_DATA_VAL(IPG_DATA_DEF_10_100); + gma_write16(sky2->hw, sky2->port, GM_SERIAL_MODE, reg); +} + +/* Enable Rx/Tx */ +static void sky2_enable_rx_tx(struct sky2_port *sky2) +{ + struct sky2_hw *hw = sky2->hw; + unsigned port = sky2->port; + u16 reg; + + reg = gma_read16(hw, port, GM_GP_CTRL); + reg |= GM_GPCR_RX_ENA | GM_GPCR_TX_ENA; + gma_write16(hw, port, GM_GP_CTRL, reg); +} + +/* Force a renegotiation */ +static void sky2_phy_reinit(struct sky2_port *sky2) +{ + spin_lock_bh(&sky2->phy_lock); + sky2_phy_init(sky2->hw, sky2->port); + sky2_enable_rx_tx(sky2); + spin_unlock_bh(&sky2->phy_lock); +} + +/* Put device in state to listen for Wake On Lan */ +static void sky2_wol_init(struct sky2_port *sky2) +{ + struct sky2_hw *hw = sky2->hw; + unsigned port = sky2->port; + enum flow_control save_mode; + u16 ctrl; + + /* Bring hardware out of reset */ + sky2_write16(hw, B0_CTST, CS_RST_CLR); + sky2_write16(hw, SK_REG(port, GMAC_LINK_CTRL), GMLC_RST_CLR); + + sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_CLR); + sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_CLR); + + /* Force to 10/100 + * sky2_reset will re-enable on resume + */ + save_mode = sky2->flow_mode; + ctrl = sky2->advertising; + + sky2->advertising &= ~(ADVERTISED_1000baseT_Half|ADVERTISED_1000baseT_Full); + sky2->flow_mode = FC_NONE; + + spin_lock_bh(&sky2->phy_lock); + sky2_phy_power_up(hw, port); + sky2_phy_init(hw, port); + spin_unlock_bh(&sky2->phy_lock); + + sky2->flow_mode = save_mode; + sky2->advertising = ctrl; + + /* Set GMAC to no flow control and auto update for speed/duplex */ + gma_write16(hw, port, GM_GP_CTRL, + GM_GPCR_FC_TX_DIS|GM_GPCR_TX_ENA|GM_GPCR_RX_ENA| + GM_GPCR_DUP_FULL|GM_GPCR_FC_RX_DIS|GM_GPCR_AU_FCT_DIS); + + /* Set WOL address */ + memcpy_toio(hw->regs + WOL_REGS(port, WOL_MAC_ADDR), + sky2->netdev->dev_addr, ETH_ALEN); + + /* Turn on appropriate WOL control bits */ + sky2_write16(hw, WOL_REGS(port, WOL_CTRL_STAT), WOL_CTL_CLEAR_RESULT); + ctrl = 0; + if (sky2->wol & WAKE_PHY) + ctrl |= WOL_CTL_ENA_PME_ON_LINK_CHG|WOL_CTL_ENA_LINK_CHG_UNIT; + else + ctrl |= WOL_CTL_DIS_PME_ON_LINK_CHG|WOL_CTL_DIS_LINK_CHG_UNIT; + + if (sky2->wol & WAKE_MAGIC) + ctrl |= WOL_CTL_ENA_PME_ON_MAGIC_PKT|WOL_CTL_ENA_MAGIC_PKT_UNIT; + else + ctrl |= WOL_CTL_DIS_PME_ON_MAGIC_PKT|WOL_CTL_DIS_MAGIC_PKT_UNIT; + + ctrl |= WOL_CTL_DIS_PME_ON_PATTERN|WOL_CTL_DIS_PATTERN_UNIT; + sky2_write16(hw, WOL_REGS(port, WOL_CTRL_STAT), ctrl); + + /* Disable PiG firmware */ + sky2_write16(hw, B0_CTST, Y2_HW_WOL_OFF); + + /* block receiver */ + sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_SET); +} + +static void sky2_set_tx_stfwd(struct sky2_hw *hw, unsigned port) +{ + struct net_device *dev = hw->dev[port]; + + if ( (hw->chip_id == CHIP_ID_YUKON_EX && + hw->chip_rev != CHIP_REV_YU_EX_A0) || + hw->chip_id >= CHIP_ID_YUKON_FE_P) { + /* Yukon-Extreme B0 and further Extreme devices */ + sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), TX_STFW_ENA); + } else if (dev->mtu > ETH_DATA_LEN) { + /* set Tx GMAC FIFO Almost Empty Threshold */ + sky2_write32(hw, SK_REG(port, TX_GMF_AE_THR), + (ECU_JUMBO_WM << 16) | ECU_AE_THR); + + sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), TX_STFW_DIS); + } else + sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), TX_STFW_ENA); +} + +static void sky2_mac_init(struct sky2_hw *hw, unsigned port) +{ + struct sky2_port *sky2 = netdev_priv(hw->dev[port]); + u16 reg; + u32 rx_reg; + int i; + const u8 *addr = hw->dev[port]->dev_addr; + + sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_SET); + sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_CLR); + + sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_CLR); + + if (hw->chip_id == CHIP_ID_YUKON_XL && + hw->chip_rev == CHIP_REV_YU_XL_A0 && + port == 1) { + /* WA DEV_472 -- looks like crossed wires on port 2 */ + /* clear GMAC 1 Control reset */ + sky2_write8(hw, SK_REG(0, GMAC_CTRL), GMC_RST_CLR); + do { + sky2_write8(hw, SK_REG(1, GMAC_CTRL), GMC_RST_SET); + sky2_write8(hw, SK_REG(1, GMAC_CTRL), GMC_RST_CLR); + } while (gm_phy_read(hw, 1, PHY_MARV_ID0) != PHY_MARV_ID0_VAL || + gm_phy_read(hw, 1, PHY_MARV_ID1) != PHY_MARV_ID1_Y2 || + gm_phy_read(hw, 1, PHY_MARV_INT_MASK) != 0); + } + + sky2_read16(hw, SK_REG(port, GMAC_IRQ_SRC)); + + /* Enable Transmit FIFO Underrun */ + sky2_write8(hw, SK_REG(port, GMAC_IRQ_MSK), GMAC_DEF_MSK); + + spin_lock_bh(&sky2->phy_lock); + sky2_phy_power_up(hw, port); + sky2_phy_init(hw, port); + spin_unlock_bh(&sky2->phy_lock); + + /* MIB clear */ + reg = gma_read16(hw, port, GM_PHY_ADDR); + gma_write16(hw, port, GM_PHY_ADDR, reg | GM_PAR_MIB_CLR); + + for (i = GM_MIB_CNT_BASE; i <= GM_MIB_CNT_END; i += 4) + gma_read16(hw, port, i); + gma_write16(hw, port, GM_PHY_ADDR, reg); + + /* transmit control */ + gma_write16(hw, port, GM_TX_CTRL, TX_COL_THR(TX_COL_DEF)); + + /* receive control reg: unicast + multicast + no FCS */ + gma_write16(hw, port, GM_RX_CTRL, + GM_RXCR_UCF_ENA | GM_RXCR_CRC_DIS | GM_RXCR_MCF_ENA); + + /* transmit flow control */ + gma_write16(hw, port, GM_TX_FLOW_CTRL, 0xffff); + + /* transmit parameter */ + gma_write16(hw, port, GM_TX_PARAM, + TX_JAM_LEN_VAL(TX_JAM_LEN_DEF) | + TX_JAM_IPG_VAL(TX_JAM_IPG_DEF) | + TX_IPG_JAM_DATA(TX_IPG_JAM_DEF) | + TX_BACK_OFF_LIM(TX_BOF_LIM_DEF)); + + /* serial mode register */ + reg = DATA_BLIND_VAL(DATA_BLIND_DEF) | + GM_SMOD_VLAN_ENA | IPG_DATA_VAL(IPG_DATA_DEF_1000); + + if (hw->dev[port]->mtu > ETH_DATA_LEN) + reg |= GM_SMOD_JUMBO_ENA; + + if (hw->chip_id == CHIP_ID_YUKON_EC_U && + hw->chip_rev == CHIP_REV_YU_EC_U_B1) + reg |= GM_NEW_FLOW_CTRL; + + gma_write16(hw, port, GM_SERIAL_MODE, reg); + + /* virtual address for data */ + gma_set_addr(hw, port, GM_SRC_ADDR_2L, addr); + + /* physical address: used for pause frames */ + gma_set_addr(hw, port, GM_SRC_ADDR_1L, addr); + + /* ignore counter overflows */ + gma_write16(hw, port, GM_TX_IRQ_MSK, 0); + gma_write16(hw, port, GM_RX_IRQ_MSK, 0); + gma_write16(hw, port, GM_TR_IRQ_MSK, 0); + + /* Configure Rx MAC FIFO */ + sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_CLR); + rx_reg = GMF_OPER_ON | GMF_RX_F_FL_ON; + if (hw->chip_id == CHIP_ID_YUKON_EX || + hw->chip_id == CHIP_ID_YUKON_FE_P) + rx_reg |= GMF_RX_OVER_ON; + + sky2_write32(hw, SK_REG(port, RX_GMF_CTRL_T), rx_reg); + + if (hw->chip_id == CHIP_ID_YUKON_XL) { + /* Hardware errata - clear flush mask */ + sky2_write16(hw, SK_REG(port, RX_GMF_FL_MSK), 0); + } else { + /* Flush Rx MAC FIFO on any flow control or error */ + sky2_write16(hw, SK_REG(port, RX_GMF_FL_MSK), GMR_FS_ANY_ERR); + } + + /* Set threshold to 0xa (64 bytes) + 1 to workaround pause bug */ + reg = RX_GMF_FL_THR_DEF + 1; + /* Another magic mystery workaround from sk98lin */ + if (hw->chip_id == CHIP_ID_YUKON_FE_P && + hw->chip_rev == CHIP_REV_YU_FE2_A0) + reg = 0x178; + sky2_write16(hw, SK_REG(port, RX_GMF_FL_THR), reg); + + /* Configure Tx MAC FIFO */ + sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_CLR); + sky2_write16(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_OPER_ON); + + /* On chips without ram buffer, pause is controlled by MAC level */ + if (!(hw->flags & SKY2_HW_RAM_BUFFER)) { + /* Pause threshold is scaled by 8 in bytes */ + if (hw->chip_id == CHIP_ID_YUKON_FE_P && + hw->chip_rev == CHIP_REV_YU_FE2_A0) + reg = 1568 / 8; + else + reg = 1024 / 8; + sky2_write16(hw, SK_REG(port, RX_GMF_UP_THR), reg); + sky2_write16(hw, SK_REG(port, RX_GMF_LP_THR), 768 / 8); + + sky2_set_tx_stfwd(hw, port); + } + + if (hw->chip_id == CHIP_ID_YUKON_FE_P && + hw->chip_rev == CHIP_REV_YU_FE2_A0) { + /* disable dynamic watermark */ + reg = sky2_read16(hw, SK_REG(port, TX_GMF_EA)); + reg &= ~TX_DYN_WM_ENA; + sky2_write16(hw, SK_REG(port, TX_GMF_EA), reg); + } +} + +/* Assign Ram Buffer allocation to queue */ +static void sky2_ramset(struct sky2_hw *hw, u16 q, u32 start, u32 space) +{ + u32 end; + + /* convert from K bytes to qwords used for hw register */ + start *= 1024/8; + space *= 1024/8; + end = start + space - 1; + + sky2_write8(hw, RB_ADDR(q, RB_CTRL), RB_RST_CLR); + sky2_write32(hw, RB_ADDR(q, RB_START), start); + sky2_write32(hw, RB_ADDR(q, RB_END), end); + sky2_write32(hw, RB_ADDR(q, RB_WP), start); + sky2_write32(hw, RB_ADDR(q, RB_RP), start); + + if (q == Q_R1 || q == Q_R2) { + u32 tp = space - space/4; + + /* On receive queue's set the thresholds + * give receiver priority when > 3/4 full + * send pause when down to 2K + */ + sky2_write32(hw, RB_ADDR(q, RB_RX_UTHP), tp); + sky2_write32(hw, RB_ADDR(q, RB_RX_LTHP), space/2); + + tp = space - 2048/8; + sky2_write32(hw, RB_ADDR(q, RB_RX_UTPP), tp); + sky2_write32(hw, RB_ADDR(q, RB_RX_LTPP), space/4); + } else { + /* Enable store & forward on Tx queue's because + * Tx FIFO is only 1K on Yukon + */ + sky2_write8(hw, RB_ADDR(q, RB_CTRL), RB_ENA_STFWD); + } + + sky2_write8(hw, RB_ADDR(q, RB_CTRL), RB_ENA_OP_MD); + sky2_read8(hw, RB_ADDR(q, RB_CTRL)); +} + +/* Setup Bus Memory Interface */ +static void sky2_qset(struct sky2_hw *hw, u16 q) +{ + sky2_write32(hw, Q_ADDR(q, Q_CSR), BMU_CLR_RESET); + sky2_write32(hw, Q_ADDR(q, Q_CSR), BMU_OPER_INIT); + sky2_write32(hw, Q_ADDR(q, Q_CSR), BMU_FIFO_OP_ON); + sky2_write32(hw, Q_ADDR(q, Q_WM), BMU_WM_DEFAULT); +} + +/* Setup prefetch unit registers. This is the interface between + * hardware and driver list elements + */ +static void sky2_prefetch_init(struct sky2_hw *hw, u32 qaddr, + dma_addr_t addr, u32 last) +{ + sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_CTRL), PREF_UNIT_RST_SET); + sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_CTRL), PREF_UNIT_RST_CLR); + sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_ADDR_HI), upper_32_bits(addr)); + sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_ADDR_LO), lower_32_bits(addr)); + sky2_write16(hw, Y2_QADDR(qaddr, PREF_UNIT_LAST_IDX), last); + sky2_write32(hw, Y2_QADDR(qaddr, PREF_UNIT_CTRL), PREF_UNIT_OP_ON); + + sky2_read32(hw, Y2_QADDR(qaddr, PREF_UNIT_CTRL)); +} + +static inline struct sky2_tx_le *get_tx_le(struct sky2_port *sky2, u16 *slot) +{ + struct sky2_tx_le *le = sky2->tx_le + *slot; + + *slot = RING_NEXT(*slot, sky2->tx_ring_size); + le->ctrl = 0; + return le; +} + +static void tx_init(struct sky2_port *sky2) +{ + struct sky2_tx_le *le; + + sky2->tx_prod = sky2->tx_cons = 0; + sky2->tx_tcpsum = 0; + sky2->tx_last_mss = 0; + + le = get_tx_le(sky2, &sky2->tx_prod); + le->addr = 0; + le->opcode = OP_ADDR64 | HW_OWNER; + sky2->tx_last_upper = 0; +} + +/* Update chip's next pointer */ +static inline void sky2_put_idx(struct sky2_hw *hw, unsigned q, u16 idx) +{ + /* Make sure write' to descriptors are complete before we tell hardware */ + wmb(); + sky2_write16(hw, Y2_QADDR(q, PREF_UNIT_PUT_IDX), idx); + + /* Synchronize I/O on since next processor may write to tail */ + mmiowb(); +} + + +static inline struct sky2_rx_le *sky2_next_rx(struct sky2_port *sky2) +{ + struct sky2_rx_le *le = sky2->rx_le + sky2->rx_put; + sky2->rx_put = RING_NEXT(sky2->rx_put, RX_LE_SIZE); + le->ctrl = 0; + return le; +} + +static unsigned sky2_get_rx_threshold(struct sky2_port *sky2) +{ + unsigned size; + + /* Space needed for frame data + headers rounded up */ + size = roundup(sky2->netdev->mtu + ETH_HLEN + VLAN_HLEN, 8); + + /* Stopping point for hardware truncation */ + return (size - 8) / sizeof(u32); +} + +static unsigned sky2_get_rx_data_size(struct sky2_port *sky2) +{ + struct rx_ring_info *re; + unsigned size; + + /* Space needed for frame data + headers rounded up */ + size = roundup(sky2->netdev->mtu + ETH_HLEN + VLAN_HLEN, 8); + + sky2->rx_nfrags = size >> PAGE_SHIFT; + BUG_ON(sky2->rx_nfrags > ARRAY_SIZE(re->frag_addr)); + + /* Compute residue after pages */ + size -= sky2->rx_nfrags << PAGE_SHIFT; + + /* Optimize to handle small packets and headers */ + if (size < copybreak) + size = copybreak; + if (size < ETH_HLEN) + size = ETH_HLEN; + + return size; +} + +/* Build description to hardware for one receive segment */ +static void sky2_rx_add(struct sky2_port *sky2, u8 op, + dma_addr_t map, unsigned len) +{ + struct sky2_rx_le *le; + + if (sizeof(dma_addr_t) > sizeof(u32)) { + le = sky2_next_rx(sky2); + le->addr = cpu_to_le32(upper_32_bits(map)); + le->opcode = OP_ADDR64 | HW_OWNER; + } + + le = sky2_next_rx(sky2); + le->addr = cpu_to_le32(lower_32_bits(map)); + le->length = cpu_to_le16(len); + le->opcode = op | HW_OWNER; +} + +/* Build description to hardware for one possibly fragmented skb */ +static void sky2_rx_submit(struct sky2_port *sky2, + const struct rx_ring_info *re) +{ + int i; + + sky2_rx_add(sky2, OP_PACKET, re->data_addr, sky2->rx_data_size); + + for (i = 0; i < skb_shinfo(re->skb)->nr_frags; i++) + sky2_rx_add(sky2, OP_BUFFER, re->frag_addr[i], PAGE_SIZE); +} + + +static int sky2_rx_map_skb(struct pci_dev *pdev, struct rx_ring_info *re, + unsigned size) +{ + struct sk_buff *skb = re->skb; + int i; + + re->data_addr = pci_map_single(pdev, skb->data, size, PCI_DMA_FROMDEVICE); + if (pci_dma_mapping_error(pdev, re->data_addr)) + goto mapping_error; + + dma_unmap_len_set(re, data_size, size); + + for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) { + skb_frag_t *frag = &skb_shinfo(skb)->frags[i]; + + re->frag_addr[i] = pci_map_page(pdev, frag->page, + frag->page_offset, + frag->size, + PCI_DMA_FROMDEVICE); + + if (pci_dma_mapping_error(pdev, re->frag_addr[i])) + goto map_page_error; + } + return 0; + +map_page_error: + while (--i >= 0) { + pci_unmap_page(pdev, re->frag_addr[i], + skb_shinfo(skb)->frags[i].size, + PCI_DMA_FROMDEVICE); + } + + pci_unmap_single(pdev, re->data_addr, dma_unmap_len(re, data_size), + PCI_DMA_FROMDEVICE); + +mapping_error: + if (net_ratelimit()) + dev_warn(&pdev->dev, "%s: rx mapping error\n", + skb->dev->name); + return -EIO; +} + +static void sky2_rx_unmap_skb(struct pci_dev *pdev, struct rx_ring_info *re) +{ + struct sk_buff *skb = re->skb; + int i; + + pci_unmap_single(pdev, re->data_addr, dma_unmap_len(re, data_size), + PCI_DMA_FROMDEVICE); + + for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) + pci_unmap_page(pdev, re->frag_addr[i], + skb_shinfo(skb)->frags[i].size, + PCI_DMA_FROMDEVICE); +} + +/* Tell chip where to start receive checksum. + * Actually has two checksums, but set both same to avoid possible byte + * order problems. + */ +static void rx_set_checksum(struct sky2_port *sky2) +{ + struct sky2_rx_le *le = sky2_next_rx(sky2); + + le->addr = cpu_to_le32((ETH_HLEN << 16) | ETH_HLEN); + le->ctrl = 0; + le->opcode = OP_TCPSTART | HW_OWNER; + + sky2_write32(sky2->hw, + Q_ADDR(rxqaddr[sky2->port], Q_CSR), + (sky2->netdev->features & NETIF_F_RXCSUM) + ? BMU_ENA_RX_CHKSUM : BMU_DIS_RX_CHKSUM); +} + +/* Enable/disable receive hash calculation (RSS) */ +static void rx_set_rss(struct net_device *dev, u32 features) +{ + struct sky2_port *sky2 = netdev_priv(dev); + struct sky2_hw *hw = sky2->hw; + int i, nkeys = 4; + + /* Supports IPv6 and other modes */ + if (hw->flags & SKY2_HW_NEW_LE) { + nkeys = 10; + sky2_write32(hw, SK_REG(sky2->port, RSS_CFG), HASH_ALL); + } + + /* Program RSS initial values */ + if (features & NETIF_F_RXHASH) { + u32 key[nkeys]; + + get_random_bytes(key, nkeys * sizeof(u32)); + for (i = 0; i < nkeys; i++) + sky2_write32(hw, SK_REG(sky2->port, RSS_KEY + i * 4), + key[i]); + + /* Need to turn on (undocumented) flag to make hashing work */ + sky2_write32(hw, SK_REG(sky2->port, RX_GMF_CTRL_T), + RX_STFW_ENA); + + sky2_write32(hw, Q_ADDR(rxqaddr[sky2->port], Q_CSR), + BMU_ENA_RX_RSS_HASH); + } else + sky2_write32(hw, Q_ADDR(rxqaddr[sky2->port], Q_CSR), + BMU_DIS_RX_RSS_HASH); +} + +/* + * The RX Stop command will not work for Yukon-2 if the BMU does not + * reach the end of packet and since we can't make sure that we have + * incoming data, we must reset the BMU while it is not doing a DMA + * transfer. Since it is possible that the RX path is still active, + * the RX RAM buffer will be stopped first, so any possible incoming + * data will not trigger a DMA. After the RAM buffer is stopped, the + * BMU is polled until any DMA in progress is ended and only then it + * will be reset. + */ +static void sky2_rx_stop(struct sky2_port *sky2) +{ + struct sky2_hw *hw = sky2->hw; + unsigned rxq = rxqaddr[sky2->port]; + int i; + + /* disable the RAM Buffer receive queue */ + sky2_write8(hw, RB_ADDR(rxq, RB_CTRL), RB_DIS_OP_MD); + + for (i = 0; i < 0xffff; i++) + if (sky2_read8(hw, RB_ADDR(rxq, Q_RSL)) + == sky2_read8(hw, RB_ADDR(rxq, Q_RL))) + goto stopped; + + netdev_warn(sky2->netdev, "receiver stop failed\n"); +stopped: + sky2_write32(hw, Q_ADDR(rxq, Q_CSR), BMU_RST_SET | BMU_FIFO_RST); + + /* reset the Rx prefetch unit */ + sky2_write32(hw, Y2_QADDR(rxq, PREF_UNIT_CTRL), PREF_UNIT_RST_SET); + mmiowb(); +} + +/* Clean out receive buffer area, assumes receiver hardware stopped */ +static void sky2_rx_clean(struct sky2_port *sky2) +{ + unsigned i; + + memset(sky2->rx_le, 0, RX_LE_BYTES); + for (i = 0; i < sky2->rx_pending; i++) { + struct rx_ring_info *re = sky2->rx_ring + i; + + if (re->skb) { + sky2_rx_unmap_skb(sky2->hw->pdev, re); + kfree_skb(re->skb); + re->skb = NULL; + } + } +} + +/* Basic MII support */ +static int sky2_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd) +{ + struct mii_ioctl_data *data = if_mii(ifr); + struct sky2_port *sky2 = netdev_priv(dev); + struct sky2_hw *hw = sky2->hw; + int err = -EOPNOTSUPP; + + if (!netif_running(dev)) + return -ENODEV; /* Phy still in reset */ + + switch (cmd) { + case SIOCGMIIPHY: + data->phy_id = PHY_ADDR_MARV; + + /* fallthru */ + case SIOCGMIIREG: { + u16 val = 0; + + spin_lock_bh(&sky2->phy_lock); + err = __gm_phy_read(hw, sky2->port, data->reg_num & 0x1f, &val); + spin_unlock_bh(&sky2->phy_lock); + + data->val_out = val; + break; + } + + case SIOCSMIIREG: + spin_lock_bh(&sky2->phy_lock); + err = gm_phy_write(hw, sky2->port, data->reg_num & 0x1f, + data->val_in); + spin_unlock_bh(&sky2->phy_lock); + break; + } + return err; +} + +#define SKY2_VLAN_OFFLOADS (NETIF_F_IP_CSUM | NETIF_F_SG | NETIF_F_TSO) + +static void sky2_vlan_mode(struct net_device *dev, u32 features) +{ + struct sky2_port *sky2 = netdev_priv(dev); + struct sky2_hw *hw = sky2->hw; + u16 port = sky2->port; + + if (features & NETIF_F_HW_VLAN_RX) + sky2_write32(hw, SK_REG(port, RX_GMF_CTRL_T), + RX_VLAN_STRIP_ON); + else + sky2_write32(hw, SK_REG(port, RX_GMF_CTRL_T), + RX_VLAN_STRIP_OFF); + + if (features & NETIF_F_HW_VLAN_TX) { + sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), + TX_VLAN_TAG_ON); + + dev->vlan_features |= SKY2_VLAN_OFFLOADS; + } else { + sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), + TX_VLAN_TAG_OFF); + + /* Can't do transmit offload of vlan without hw vlan */ + dev->vlan_features &= ~SKY2_VLAN_OFFLOADS; + } +} + +/* Amount of required worst case padding in rx buffer */ +static inline unsigned sky2_rx_pad(const struct sky2_hw *hw) +{ + return (hw->flags & SKY2_HW_RAM_BUFFER) ? 8 : 2; +} + +/* + * Allocate an skb for receiving. If the MTU is large enough + * make the skb non-linear with a fragment list of pages. + */ +static struct sk_buff *sky2_rx_alloc(struct sky2_port *sky2, gfp_t gfp) +{ + struct sk_buff *skb; + int i; + + skb = __netdev_alloc_skb(sky2->netdev, + sky2->rx_data_size + sky2_rx_pad(sky2->hw), + gfp); + if (!skb) + goto nomem; + + if (sky2->hw->flags & SKY2_HW_RAM_BUFFER) { + unsigned char *start; + /* + * Workaround for a bug in FIFO that cause hang + * if the FIFO if the receive buffer is not 64 byte aligned. + * The buffer returned from netdev_alloc_skb is + * aligned except if slab debugging is enabled. + */ + start = PTR_ALIGN(skb->data, 8); + skb_reserve(skb, start - skb->data); + } else + skb_reserve(skb, NET_IP_ALIGN); + + for (i = 0; i < sky2->rx_nfrags; i++) { + struct page *page = alloc_page(gfp); + + if (!page) + goto free_partial; + skb_fill_page_desc(skb, i, page, 0, PAGE_SIZE); + } + + return skb; +free_partial: + kfree_skb(skb); +nomem: + return NULL; +} + +static inline void sky2_rx_update(struct sky2_port *sky2, unsigned rxq) +{ + sky2_put_idx(sky2->hw, rxq, sky2->rx_put); +} + +static int sky2_alloc_rx_skbs(struct sky2_port *sky2) +{ + struct sky2_hw *hw = sky2->hw; + unsigned i; + + sky2->rx_data_size = sky2_get_rx_data_size(sky2); + + /* Fill Rx ring */ + for (i = 0; i < sky2->rx_pending; i++) { + struct rx_ring_info *re = sky2->rx_ring + i; + + re->skb = sky2_rx_alloc(sky2, GFP_KERNEL); + if (!re->skb) + return -ENOMEM; + + if (sky2_rx_map_skb(hw->pdev, re, sky2->rx_data_size)) { + dev_kfree_skb(re->skb); + re->skb = NULL; + return -ENOMEM; + } + } + return 0; +} + +/* + * Setup receiver buffer pool. + * Normal case this ends up creating one list element for skb + * in the receive ring. Worst case if using large MTU and each + * allocation falls on a different 64 bit region, that results + * in 6 list elements per ring entry. + * One element is used for checksum enable/disable, and one + * extra to avoid wrap. + */ +static void sky2_rx_start(struct sky2_port *sky2) +{ + struct sky2_hw *hw = sky2->hw; + struct rx_ring_info *re; + unsigned rxq = rxqaddr[sky2->port]; + unsigned i, thresh; + + sky2->rx_put = sky2->rx_next = 0; + sky2_qset(hw, rxq); + + /* On PCI express lowering the watermark gives better performance */ + if (pci_is_pcie(hw->pdev)) + sky2_write32(hw, Q_ADDR(rxq, Q_WM), BMU_WM_PEX); + + /* These chips have no ram buffer? + * MAC Rx RAM Read is controlled by hardware */ + if (hw->chip_id == CHIP_ID_YUKON_EC_U && + hw->chip_rev > CHIP_REV_YU_EC_U_A0) + sky2_write32(hw, Q_ADDR(rxq, Q_TEST), F_M_RX_RAM_DIS); + + sky2_prefetch_init(hw, rxq, sky2->rx_le_map, RX_LE_SIZE - 1); + + if (!(hw->flags & SKY2_HW_NEW_LE)) + rx_set_checksum(sky2); + + if (!(hw->flags & SKY2_HW_RSS_BROKEN)) + rx_set_rss(sky2->netdev, sky2->netdev->features); + + /* submit Rx ring */ + for (i = 0; i < sky2->rx_pending; i++) { + re = sky2->rx_ring + i; + sky2_rx_submit(sky2, re); + } + + /* + * The receiver hangs if it receives frames larger than the + * packet buffer. As a workaround, truncate oversize frames, but + * the register is limited to 9 bits, so if you do frames > 2052 + * you better get the MTU right! + */ + thresh = sky2_get_rx_threshold(sky2); + if (thresh > 0x1ff) + sky2_write32(hw, SK_REG(sky2->port, RX_GMF_CTRL_T), RX_TRUNC_OFF); + else { + sky2_write16(hw, SK_REG(sky2->port, RX_GMF_TR_THR), thresh); + sky2_write32(hw, SK_REG(sky2->port, RX_GMF_CTRL_T), RX_TRUNC_ON); + } + + /* Tell chip about available buffers */ + sky2_rx_update(sky2, rxq); + + if (hw->chip_id == CHIP_ID_YUKON_EX || + hw->chip_id == CHIP_ID_YUKON_SUPR) { + /* + * Disable flushing of non ASF packets; + * must be done after initializing the BMUs; + * drivers without ASF support should do this too, otherwise + * it may happen that they cannot run on ASF devices; + * remember that the MAC FIFO isn't reset during initialization. + */ + sky2_write32(hw, SK_REG(sky2->port, RX_GMF_CTRL_T), RX_MACSEC_FLUSH_OFF); + } + + if (hw->chip_id >= CHIP_ID_YUKON_SUPR) { + /* Enable RX Home Address & Routing Header checksum fix */ + sky2_write16(hw, SK_REG(sky2->port, RX_GMF_FL_CTRL), + RX_IPV6_SA_MOB_ENA | RX_IPV6_DA_MOB_ENA); + + /* Enable TX Home Address & Routing Header checksum fix */ + sky2_write32(hw, Q_ADDR(txqaddr[sky2->port], Q_TEST), + TBMU_TEST_HOME_ADD_FIX_EN | TBMU_TEST_ROUTING_ADD_FIX_EN); + } +} + +static int sky2_alloc_buffers(struct sky2_port *sky2) +{ + struct sky2_hw *hw = sky2->hw; + + /* must be power of 2 */ + sky2->tx_le = pci_alloc_consistent(hw->pdev, + sky2->tx_ring_size * + sizeof(struct sky2_tx_le), + &sky2->tx_le_map); + if (!sky2->tx_le) + goto nomem; + + sky2->tx_ring = kcalloc(sky2->tx_ring_size, sizeof(struct tx_ring_info), + GFP_KERNEL); + if (!sky2->tx_ring) + goto nomem; + + sky2->rx_le = pci_alloc_consistent(hw->pdev, RX_LE_BYTES, + &sky2->rx_le_map); + if (!sky2->rx_le) + goto nomem; + memset(sky2->rx_le, 0, RX_LE_BYTES); + + sky2->rx_ring = kcalloc(sky2->rx_pending, sizeof(struct rx_ring_info), + GFP_KERNEL); + if (!sky2->rx_ring) + goto nomem; + + return sky2_alloc_rx_skbs(sky2); +nomem: + return -ENOMEM; +} + +static void sky2_free_buffers(struct sky2_port *sky2) +{ + struct sky2_hw *hw = sky2->hw; + + sky2_rx_clean(sky2); + + if (sky2->rx_le) { + pci_free_consistent(hw->pdev, RX_LE_BYTES, + sky2->rx_le, sky2->rx_le_map); + sky2->rx_le = NULL; + } + if (sky2->tx_le) { + pci_free_consistent(hw->pdev, + sky2->tx_ring_size * sizeof(struct sky2_tx_le), + sky2->tx_le, sky2->tx_le_map); + sky2->tx_le = NULL; + } + kfree(sky2->tx_ring); + kfree(sky2->rx_ring); + + sky2->tx_ring = NULL; + sky2->rx_ring = NULL; +} + +static void sky2_hw_up(struct sky2_port *sky2) +{ + struct sky2_hw *hw = sky2->hw; + unsigned port = sky2->port; + u32 ramsize; + int cap; + struct net_device *otherdev = hw->dev[sky2->port^1]; + + tx_init(sky2); + + /* + * On dual port PCI-X card, there is an problem where status + * can be received out of order due to split transactions + */ + if (otherdev && netif_running(otherdev) && + (cap = pci_find_capability(hw->pdev, PCI_CAP_ID_PCIX))) { + u16 cmd; + + cmd = sky2_pci_read16(hw, cap + PCI_X_CMD); + cmd &= ~PCI_X_CMD_MAX_SPLIT; + sky2_pci_write16(hw, cap + PCI_X_CMD, cmd); + } + + sky2_mac_init(hw, port); + + /* Register is number of 4K blocks on internal RAM buffer. */ + ramsize = sky2_read8(hw, B2_E_0) * 4; + if (ramsize > 0) { + u32 rxspace; + + netdev_dbg(sky2->netdev, "ram buffer %dK\n", ramsize); + if (ramsize < 16) + rxspace = ramsize / 2; + else + rxspace = 8 + (2*(ramsize - 16))/3; + + sky2_ramset(hw, rxqaddr[port], 0, rxspace); + sky2_ramset(hw, txqaddr[port], rxspace, ramsize - rxspace); + + /* Make sure SyncQ is disabled */ + sky2_write8(hw, RB_ADDR(port == 0 ? Q_XS1 : Q_XS2, RB_CTRL), + RB_RST_SET); + } + + sky2_qset(hw, txqaddr[port]); + + /* This is copied from sk98lin 10.0.5.3; no one tells me about erratta's */ + if (hw->chip_id == CHIP_ID_YUKON_EX && hw->chip_rev == CHIP_REV_YU_EX_B0) + sky2_write32(hw, Q_ADDR(txqaddr[port], Q_TEST), F_TX_CHK_AUTO_OFF); + + /* Set almost empty threshold */ + if (hw->chip_id == CHIP_ID_YUKON_EC_U && + hw->chip_rev == CHIP_REV_YU_EC_U_A0) + sky2_write16(hw, Q_ADDR(txqaddr[port], Q_AL), ECU_TXFF_LEV); + + sky2_prefetch_init(hw, txqaddr[port], sky2->tx_le_map, + sky2->tx_ring_size - 1); + + sky2_vlan_mode(sky2->netdev, sky2->netdev->features); + netdev_update_features(sky2->netdev); + + sky2_rx_start(sky2); +} + +/* Bring up network interface. */ +static int sky2_up(struct net_device *dev) +{ + struct sky2_port *sky2 = netdev_priv(dev); + struct sky2_hw *hw = sky2->hw; + unsigned port = sky2->port; + u32 imask; + int err; + + netif_carrier_off(dev); + + err = sky2_alloc_buffers(sky2); + if (err) + goto err_out; + + sky2_hw_up(sky2); + + /* Enable interrupts from phy/mac for port */ + imask = sky2_read32(hw, B0_IMSK); + imask |= portirq_msk[port]; + sky2_write32(hw, B0_IMSK, imask); + sky2_read32(hw, B0_IMSK); + + netif_info(sky2, ifup, dev, "enabling interface\n"); + + return 0; + +err_out: + sky2_free_buffers(sky2); + return err; +} + +/* Modular subtraction in ring */ +static inline int tx_inuse(const struct sky2_port *sky2) +{ + return (sky2->tx_prod - sky2->tx_cons) & (sky2->tx_ring_size - 1); +} + +/* Number of list elements available for next tx */ +static inline int tx_avail(const struct sky2_port *sky2) +{ + return sky2->tx_pending - tx_inuse(sky2); +} + +/* Estimate of number of transmit list elements required */ +static unsigned tx_le_req(const struct sk_buff *skb) +{ + unsigned count; + + count = (skb_shinfo(skb)->nr_frags + 1) + * (sizeof(dma_addr_t) / sizeof(u32)); + + if (skb_is_gso(skb)) + ++count; + else if (sizeof(dma_addr_t) == sizeof(u32)) + ++count; /* possible vlan */ + + if (skb->ip_summed == CHECKSUM_PARTIAL) + ++count; + + return count; +} + +static void sky2_tx_unmap(struct pci_dev *pdev, struct tx_ring_info *re) +{ + if (re->flags & TX_MAP_SINGLE) + pci_unmap_single(pdev, dma_unmap_addr(re, mapaddr), + dma_unmap_len(re, maplen), + PCI_DMA_TODEVICE); + else if (re->flags & TX_MAP_PAGE) + pci_unmap_page(pdev, dma_unmap_addr(re, mapaddr), + dma_unmap_len(re, maplen), + PCI_DMA_TODEVICE); + re->flags = 0; +} + +/* + * Put one packet in ring for transmit. + * A single packet can generate multiple list elements, and + * the number of ring elements will probably be less than the number + * of list elements used. + */ +static netdev_tx_t sky2_xmit_frame(struct sk_buff *skb, + struct net_device *dev) +{ + struct sky2_port *sky2 = netdev_priv(dev); + struct sky2_hw *hw = sky2->hw; + struct sky2_tx_le *le = NULL; + struct tx_ring_info *re; + unsigned i, len; + dma_addr_t mapping; + u32 upper; + u16 slot; + u16 mss; + u8 ctrl; + + if (unlikely(tx_avail(sky2) < tx_le_req(skb))) + return NETDEV_TX_BUSY; + + len = skb_headlen(skb); + mapping = pci_map_single(hw->pdev, skb->data, len, PCI_DMA_TODEVICE); + + if (pci_dma_mapping_error(hw->pdev, mapping)) + goto mapping_error; + + slot = sky2->tx_prod; + netif_printk(sky2, tx_queued, KERN_DEBUG, dev, + "tx queued, slot %u, len %d\n", slot, skb->len); + + /* Send high bits if needed */ + upper = upper_32_bits(mapping); + if (upper != sky2->tx_last_upper) { + le = get_tx_le(sky2, &slot); + le->addr = cpu_to_le32(upper); + sky2->tx_last_upper = upper; + le->opcode = OP_ADDR64 | HW_OWNER; + } + + /* Check for TCP Segmentation Offload */ + mss = skb_shinfo(skb)->gso_size; + if (mss != 0) { + + if (!(hw->flags & SKY2_HW_NEW_LE)) + mss += ETH_HLEN + ip_hdrlen(skb) + tcp_hdrlen(skb); + + if (mss != sky2->tx_last_mss) { + le = get_tx_le(sky2, &slot); + le->addr = cpu_to_le32(mss); + + if (hw->flags & SKY2_HW_NEW_LE) + le->opcode = OP_MSS | HW_OWNER; + else + le->opcode = OP_LRGLEN | HW_OWNER; + sky2->tx_last_mss = mss; + } + } + + ctrl = 0; + + /* Add VLAN tag, can piggyback on LRGLEN or ADDR64 */ + if (vlan_tx_tag_present(skb)) { + if (!le) { + le = get_tx_le(sky2, &slot); + le->addr = 0; + le->opcode = OP_VLAN|HW_OWNER; + } else + le->opcode |= OP_VLAN; + le->length = cpu_to_be16(vlan_tx_tag_get(skb)); + ctrl |= INS_VLAN; + } + + /* Handle TCP checksum offload */ + if (skb->ip_summed == CHECKSUM_PARTIAL) { + /* On Yukon EX (some versions) encoding change. */ + if (hw->flags & SKY2_HW_AUTO_TX_SUM) + ctrl |= CALSUM; /* auto checksum */ + else { + const unsigned offset = skb_transport_offset(skb); + u32 tcpsum; + + tcpsum = offset << 16; /* sum start */ + tcpsum |= offset + skb->csum_offset; /* sum write */ + + ctrl |= CALSUM | WR_SUM | INIT_SUM | LOCK_SUM; + if (ip_hdr(skb)->protocol == IPPROTO_UDP) + ctrl |= UDPTCP; + + if (tcpsum != sky2->tx_tcpsum) { + sky2->tx_tcpsum = tcpsum; + + le = get_tx_le(sky2, &slot); + le->addr = cpu_to_le32(tcpsum); + le->length = 0; /* initial checksum value */ + le->ctrl = 1; /* one packet */ + le->opcode = OP_TCPLISW | HW_OWNER; + } + } + } + + re = sky2->tx_ring + slot; + re->flags = TX_MAP_SINGLE; + dma_unmap_addr_set(re, mapaddr, mapping); + dma_unmap_len_set(re, maplen, len); + + le = get_tx_le(sky2, &slot); + le->addr = cpu_to_le32(lower_32_bits(mapping)); + le->length = cpu_to_le16(len); + le->ctrl = ctrl; + le->opcode = mss ? (OP_LARGESEND | HW_OWNER) : (OP_PACKET | HW_OWNER); + + + for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) { + const skb_frag_t *frag = &skb_shinfo(skb)->frags[i]; + + mapping = pci_map_page(hw->pdev, frag->page, frag->page_offset, + frag->size, PCI_DMA_TODEVICE); + + if (pci_dma_mapping_error(hw->pdev, mapping)) + goto mapping_unwind; + + upper = upper_32_bits(mapping); + if (upper != sky2->tx_last_upper) { + le = get_tx_le(sky2, &slot); + le->addr = cpu_to_le32(upper); + sky2->tx_last_upper = upper; + le->opcode = OP_ADDR64 | HW_OWNER; + } + + re = sky2->tx_ring + slot; + re->flags = TX_MAP_PAGE; + dma_unmap_addr_set(re, mapaddr, mapping); + dma_unmap_len_set(re, maplen, frag->size); + + le = get_tx_le(sky2, &slot); + le->addr = cpu_to_le32(lower_32_bits(mapping)); + le->length = cpu_to_le16(frag->size); + le->ctrl = ctrl; + le->opcode = OP_BUFFER | HW_OWNER; + } + + re->skb = skb; + le->ctrl |= EOP; + + sky2->tx_prod = slot; + + if (tx_avail(sky2) <= MAX_SKB_TX_LE) + netif_stop_queue(dev); + + sky2_put_idx(hw, txqaddr[sky2->port], sky2->tx_prod); + + return NETDEV_TX_OK; + +mapping_unwind: + for (i = sky2->tx_prod; i != slot; i = RING_NEXT(i, sky2->tx_ring_size)) { + re = sky2->tx_ring + i; + + sky2_tx_unmap(hw->pdev, re); + } + +mapping_error: + if (net_ratelimit()) + dev_warn(&hw->pdev->dev, "%s: tx mapping error\n", dev->name); + dev_kfree_skb(skb); + return NETDEV_TX_OK; +} + +/* + * Free ring elements from starting at tx_cons until "done" + * + * NB: + * 1. The hardware will tell us about partial completion of multi-part + * buffers so make sure not to free skb to early. + * 2. This may run in parallel start_xmit because the it only + * looks at the tail of the queue of FIFO (tx_cons), not + * the head (tx_prod) + */ +static void sky2_tx_complete(struct sky2_port *sky2, u16 done) +{ + struct net_device *dev = sky2->netdev; + unsigned idx; + + BUG_ON(done >= sky2->tx_ring_size); + + for (idx = sky2->tx_cons; idx != done; + idx = RING_NEXT(idx, sky2->tx_ring_size)) { + struct tx_ring_info *re = sky2->tx_ring + idx; + struct sk_buff *skb = re->skb; + + sky2_tx_unmap(sky2->hw->pdev, re); + + if (skb) { + netif_printk(sky2, tx_done, KERN_DEBUG, dev, + "tx done %u\n", idx); + + u64_stats_update_begin(&sky2->tx_stats.syncp); + ++sky2->tx_stats.packets; + sky2->tx_stats.bytes += skb->len; + u64_stats_update_end(&sky2->tx_stats.syncp); + + re->skb = NULL; + dev_kfree_skb_any(skb); + + sky2->tx_next = RING_NEXT(idx, sky2->tx_ring_size); + } + } + + sky2->tx_cons = idx; + smp_mb(); +} + +static void sky2_tx_reset(struct sky2_hw *hw, unsigned port) +{ + /* Disable Force Sync bit and Enable Alloc bit */ + sky2_write8(hw, SK_REG(port, TXA_CTRL), + TXA_DIS_FSYNC | TXA_DIS_ALLOC | TXA_STOP_RC); + + /* Stop Interval Timer and Limit Counter of Tx Arbiter */ + sky2_write32(hw, SK_REG(port, TXA_ITI_INI), 0L); + sky2_write32(hw, SK_REG(port, TXA_LIM_INI), 0L); + + /* Reset the PCI FIFO of the async Tx queue */ + sky2_write32(hw, Q_ADDR(txqaddr[port], Q_CSR), + BMU_RST_SET | BMU_FIFO_RST); + + /* Reset the Tx prefetch units */ + sky2_write32(hw, Y2_QADDR(txqaddr[port], PREF_UNIT_CTRL), + PREF_UNIT_RST_SET); + + sky2_write32(hw, RB_ADDR(txqaddr[port], RB_CTRL), RB_RST_SET); + sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_SET); +} + +static void sky2_hw_down(struct sky2_port *sky2) +{ + struct sky2_hw *hw = sky2->hw; + unsigned port = sky2->port; + u16 ctrl; + + /* Force flow control off */ + sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF); + + /* Stop transmitter */ + sky2_write32(hw, Q_ADDR(txqaddr[port], Q_CSR), BMU_STOP); + sky2_read32(hw, Q_ADDR(txqaddr[port], Q_CSR)); + + sky2_write32(hw, RB_ADDR(txqaddr[port], RB_CTRL), + RB_RST_SET | RB_DIS_OP_MD); + + ctrl = gma_read16(hw, port, GM_GP_CTRL); + ctrl &= ~(GM_GPCR_TX_ENA | GM_GPCR_RX_ENA); + gma_write16(hw, port, GM_GP_CTRL, ctrl); + + sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_SET); + + /* Workaround shared GMAC reset */ + if (!(hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev == 0 && + port == 0 && hw->dev[1] && netif_running(hw->dev[1]))) + sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_SET); + + sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_SET); + + /* Force any delayed status interrrupt and NAPI */ + sky2_write32(hw, STAT_LEV_TIMER_CNT, 0); + sky2_write32(hw, STAT_TX_TIMER_CNT, 0); + sky2_write32(hw, STAT_ISR_TIMER_CNT, 0); + sky2_read8(hw, STAT_ISR_TIMER_CTRL); + + sky2_rx_stop(sky2); + + spin_lock_bh(&sky2->phy_lock); + sky2_phy_power_down(hw, port); + spin_unlock_bh(&sky2->phy_lock); + + sky2_tx_reset(hw, port); + + /* Free any pending frames stuck in HW queue */ + sky2_tx_complete(sky2, sky2->tx_prod); +} + +/* Network shutdown */ +static int sky2_down(struct net_device *dev) +{ + struct sky2_port *sky2 = netdev_priv(dev); + struct sky2_hw *hw = sky2->hw; + + /* Never really got started! */ + if (!sky2->tx_le) + return 0; + + netif_info(sky2, ifdown, dev, "disabling interface\n"); + + /* Disable port IRQ */ + sky2_write32(hw, B0_IMSK, + sky2_read32(hw, B0_IMSK) & ~portirq_msk[sky2->port]); + sky2_read32(hw, B0_IMSK); + + synchronize_irq(hw->pdev->irq); + napi_synchronize(&hw->napi); + + sky2_hw_down(sky2); + + sky2_free_buffers(sky2); + + return 0; +} + +static u16 sky2_phy_speed(const struct sky2_hw *hw, u16 aux) +{ + if (hw->flags & SKY2_HW_FIBRE_PHY) + return SPEED_1000; + + if (!(hw->flags & SKY2_HW_GIGABIT)) { + if (aux & PHY_M_PS_SPEED_100) + return SPEED_100; + else + return SPEED_10; + } + + switch (aux & PHY_M_PS_SPEED_MSK) { + case PHY_M_PS_SPEED_1000: + return SPEED_1000; + case PHY_M_PS_SPEED_100: + return SPEED_100; + default: + return SPEED_10; + } +} + +static void sky2_link_up(struct sky2_port *sky2) +{ + struct sky2_hw *hw = sky2->hw; + unsigned port = sky2->port; + static const char *fc_name[] = { + [FC_NONE] = "none", + [FC_TX] = "tx", + [FC_RX] = "rx", + [FC_BOTH] = "both", + }; + + sky2_set_ipg(sky2); + + sky2_enable_rx_tx(sky2); + + gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_DEF_MSK); + + netif_carrier_on(sky2->netdev); + + mod_timer(&hw->watchdog_timer, jiffies + 1); + + /* Turn on link LED */ + sky2_write8(hw, SK_REG(port, LNK_LED_REG), + LINKLED_ON | LINKLED_BLINK_OFF | LINKLED_LINKSYNC_OFF); + + netif_info(sky2, link, sky2->netdev, + "Link is up at %d Mbps, %s duplex, flow control %s\n", + sky2->speed, + sky2->duplex == DUPLEX_FULL ? "full" : "half", + fc_name[sky2->flow_status]); +} + +static void sky2_link_down(struct sky2_port *sky2) +{ + struct sky2_hw *hw = sky2->hw; + unsigned port = sky2->port; + u16 reg; + + gm_phy_write(hw, port, PHY_MARV_INT_MASK, 0); + + reg = gma_read16(hw, port, GM_GP_CTRL); + reg &= ~(GM_GPCR_RX_ENA | GM_GPCR_TX_ENA); + gma_write16(hw, port, GM_GP_CTRL, reg); + + netif_carrier_off(sky2->netdev); + + /* Turn off link LED */ + sky2_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_OFF); + + netif_info(sky2, link, sky2->netdev, "Link is down\n"); + + sky2_phy_init(hw, port); +} + +static enum flow_control sky2_flow(int rx, int tx) +{ + if (rx) + return tx ? FC_BOTH : FC_RX; + else + return tx ? FC_TX : FC_NONE; +} + +static int sky2_autoneg_done(struct sky2_port *sky2, u16 aux) +{ + struct sky2_hw *hw = sky2->hw; + unsigned port = sky2->port; + u16 advert, lpa; + + advert = gm_phy_read(hw, port, PHY_MARV_AUNE_ADV); + lpa = gm_phy_read(hw, port, PHY_MARV_AUNE_LP); + if (lpa & PHY_M_AN_RF) { + netdev_err(sky2->netdev, "remote fault\n"); + return -1; + } + + if (!(aux & PHY_M_PS_SPDUP_RES)) { + netdev_err(sky2->netdev, "speed/duplex mismatch\n"); + return -1; + } + + sky2->speed = sky2_phy_speed(hw, aux); + sky2->duplex = (aux & PHY_M_PS_FULL_DUP) ? DUPLEX_FULL : DUPLEX_HALF; + + /* Since the pause result bits seem to in different positions on + * different chips. look at registers. + */ + if (hw->flags & SKY2_HW_FIBRE_PHY) { + /* Shift for bits in fiber PHY */ + advert &= ~(ADVERTISE_PAUSE_CAP|ADVERTISE_PAUSE_ASYM); + lpa &= ~(LPA_PAUSE_CAP|LPA_PAUSE_ASYM); + + if (advert & ADVERTISE_1000XPAUSE) + advert |= ADVERTISE_PAUSE_CAP; + if (advert & ADVERTISE_1000XPSE_ASYM) + advert |= ADVERTISE_PAUSE_ASYM; + if (lpa & LPA_1000XPAUSE) + lpa |= LPA_PAUSE_CAP; + if (lpa & LPA_1000XPAUSE_ASYM) + lpa |= LPA_PAUSE_ASYM; + } + + sky2->flow_status = FC_NONE; + if (advert & ADVERTISE_PAUSE_CAP) { + if (lpa & LPA_PAUSE_CAP) + sky2->flow_status = FC_BOTH; + else if (advert & ADVERTISE_PAUSE_ASYM) + sky2->flow_status = FC_RX; + } else if (advert & ADVERTISE_PAUSE_ASYM) { + if ((lpa & LPA_PAUSE_CAP) && (lpa & LPA_PAUSE_ASYM)) + sky2->flow_status = FC_TX; + } + + if (sky2->duplex == DUPLEX_HALF && sky2->speed < SPEED_1000 && + !(hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_EX)) + sky2->flow_status = FC_NONE; + + if (sky2->flow_status & FC_TX) + sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_ON); + else + sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF); + + return 0; +} + +/* Interrupt from PHY */ +static void sky2_phy_intr(struct sky2_hw *hw, unsigned port) +{ + struct net_device *dev = hw->dev[port]; + struct sky2_port *sky2 = netdev_priv(dev); + u16 istatus, phystat; + + if (!netif_running(dev)) + return; + + spin_lock(&sky2->phy_lock); + istatus = gm_phy_read(hw, port, PHY_MARV_INT_STAT); + phystat = gm_phy_read(hw, port, PHY_MARV_PHY_STAT); + + netif_info(sky2, intr, sky2->netdev, "phy interrupt status 0x%x 0x%x\n", + istatus, phystat); + + if (istatus & PHY_M_IS_AN_COMPL) { + if (sky2_autoneg_done(sky2, phystat) == 0 && + !netif_carrier_ok(dev)) + sky2_link_up(sky2); + goto out; + } + + if (istatus & PHY_M_IS_LSP_CHANGE) + sky2->speed = sky2_phy_speed(hw, phystat); + + if (istatus & PHY_M_IS_DUP_CHANGE) + sky2->duplex = + (phystat & PHY_M_PS_FULL_DUP) ? DUPLEX_FULL : DUPLEX_HALF; + + if (istatus & PHY_M_IS_LST_CHANGE) { + if (phystat & PHY_M_PS_LINK_UP) + sky2_link_up(sky2); + else + sky2_link_down(sky2); + } +out: + spin_unlock(&sky2->phy_lock); +} + +/* Special quick link interrupt (Yukon-2 Optima only) */ +static void sky2_qlink_intr(struct sky2_hw *hw) +{ + struct sky2_port *sky2 = netdev_priv(hw->dev[0]); + u32 imask; + u16 phy; + + /* disable irq */ + imask = sky2_read32(hw, B0_IMSK); + imask &= ~Y2_IS_PHY_QLNK; + sky2_write32(hw, B0_IMSK, imask); + + /* reset PHY Link Detect */ + phy = sky2_pci_read16(hw, PSM_CONFIG_REG4); + sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON); + sky2_pci_write16(hw, PSM_CONFIG_REG4, phy | 1); + sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF); + + sky2_link_up(sky2); +} + +/* Transmit timeout is only called if we are running, carrier is up + * and tx queue is full (stopped). + */ +static void sky2_tx_timeout(struct net_device *dev) +{ + struct sky2_port *sky2 = netdev_priv(dev); + struct sky2_hw *hw = sky2->hw; + + netif_err(sky2, timer, dev, "tx timeout\n"); + + netdev_printk(KERN_DEBUG, dev, "transmit ring %u .. %u report=%u done=%u\n", + sky2->tx_cons, sky2->tx_prod, + sky2_read16(hw, sky2->port == 0 ? STAT_TXA1_RIDX : STAT_TXA2_RIDX), + sky2_read16(hw, Q_ADDR(txqaddr[sky2->port], Q_DONE))); + + /* can't restart safely under softirq */ + schedule_work(&hw->restart_work); +} + +static int sky2_change_mtu(struct net_device *dev, int new_mtu) +{ + struct sky2_port *sky2 = netdev_priv(dev); + struct sky2_hw *hw = sky2->hw; + unsigned port = sky2->port; + int err; + u16 ctl, mode; + u32 imask; + + /* MTU size outside the spec */ + if (new_mtu < ETH_ZLEN || new_mtu > ETH_JUMBO_MTU) + return -EINVAL; + + /* MTU > 1500 on yukon FE and FE+ not allowed */ + if (new_mtu > ETH_DATA_LEN && + (hw->chip_id == CHIP_ID_YUKON_FE || + hw->chip_id == CHIP_ID_YUKON_FE_P)) + return -EINVAL; + + if (!netif_running(dev)) { + dev->mtu = new_mtu; + netdev_update_features(dev); + return 0; + } + + imask = sky2_read32(hw, B0_IMSK); + sky2_write32(hw, B0_IMSK, 0); + + dev->trans_start = jiffies; /* prevent tx timeout */ + napi_disable(&hw->napi); + netif_tx_disable(dev); + + synchronize_irq(hw->pdev->irq); + + if (!(hw->flags & SKY2_HW_RAM_BUFFER)) + sky2_set_tx_stfwd(hw, port); + + ctl = gma_read16(hw, port, GM_GP_CTRL); + gma_write16(hw, port, GM_GP_CTRL, ctl & ~GM_GPCR_RX_ENA); + sky2_rx_stop(sky2); + sky2_rx_clean(sky2); + + dev->mtu = new_mtu; + netdev_update_features(dev); + + mode = DATA_BLIND_VAL(DATA_BLIND_DEF) | GM_SMOD_VLAN_ENA; + if (sky2->speed > SPEED_100) + mode |= IPG_DATA_VAL(IPG_DATA_DEF_1000); + else + mode |= IPG_DATA_VAL(IPG_DATA_DEF_10_100); + + if (dev->mtu > ETH_DATA_LEN) + mode |= GM_SMOD_JUMBO_ENA; + + gma_write16(hw, port, GM_SERIAL_MODE, mode); + + sky2_write8(hw, RB_ADDR(rxqaddr[port], RB_CTRL), RB_ENA_OP_MD); + + err = sky2_alloc_rx_skbs(sky2); + if (!err) + sky2_rx_start(sky2); + else + sky2_rx_clean(sky2); + sky2_write32(hw, B0_IMSK, imask); + + sky2_read32(hw, B0_Y2_SP_LISR); + napi_enable(&hw->napi); + + if (err) + dev_close(dev); + else { + gma_write16(hw, port, GM_GP_CTRL, ctl); + + netif_wake_queue(dev); + } + + return err; +} + +/* For small just reuse existing skb for next receive */ +static struct sk_buff *receive_copy(struct sky2_port *sky2, + const struct rx_ring_info *re, + unsigned length) +{ + struct sk_buff *skb; + + skb = netdev_alloc_skb_ip_align(sky2->netdev, length); + if (likely(skb)) { + pci_dma_sync_single_for_cpu(sky2->hw->pdev, re->data_addr, + length, PCI_DMA_FROMDEVICE); + skb_copy_from_linear_data(re->skb, skb->data, length); + skb->ip_summed = re->skb->ip_summed; + skb->csum = re->skb->csum; + pci_dma_sync_single_for_device(sky2->hw->pdev, re->data_addr, + length, PCI_DMA_FROMDEVICE); + re->skb->ip_summed = CHECKSUM_NONE; + skb_put(skb, length); + } + return skb; +} + +/* Adjust length of skb with fragments to match received data */ +static void skb_put_frags(struct sk_buff *skb, unsigned int hdr_space, + unsigned int length) +{ + int i, num_frags; + unsigned int size; + + /* put header into skb */ + size = min(length, hdr_space); + skb->tail += size; + skb->len += size; + length -= size; + + num_frags = skb_shinfo(skb)->nr_frags; + for (i = 0; i < num_frags; i++) { + skb_frag_t *frag = &skb_shinfo(skb)->frags[i]; + + if (length == 0) { + /* don't need this page */ + __free_page(frag->page); + --skb_shinfo(skb)->nr_frags; + } else { + size = min(length, (unsigned) PAGE_SIZE); + + frag->size = size; + skb->data_len += size; + skb->truesize += size; + skb->len += size; + length -= size; + } + } +} + +/* Normal packet - take skb from ring element and put in a new one */ +static struct sk_buff *receive_new(struct sky2_port *sky2, + struct rx_ring_info *re, + unsigned int length) +{ + struct sk_buff *skb; + struct rx_ring_info nre; + unsigned hdr_space = sky2->rx_data_size; + + nre.skb = sky2_rx_alloc(sky2, GFP_ATOMIC); + if (unlikely(!nre.skb)) + goto nobuf; + + if (sky2_rx_map_skb(sky2->hw->pdev, &nre, hdr_space)) + goto nomap; + + skb = re->skb; + sky2_rx_unmap_skb(sky2->hw->pdev, re); + prefetch(skb->data); + *re = nre; + + if (skb_shinfo(skb)->nr_frags) + skb_put_frags(skb, hdr_space, length); + else + skb_put(skb, length); + return skb; + +nomap: + dev_kfree_skb(nre.skb); +nobuf: + return NULL; +} + +/* + * Receive one packet. + * For larger packets, get new buffer. + */ +static struct sk_buff *sky2_receive(struct net_device *dev, + u16 length, u32 status) +{ + struct sky2_port *sky2 = netdev_priv(dev); + struct rx_ring_info *re = sky2->rx_ring + sky2->rx_next; + struct sk_buff *skb = NULL; + u16 count = (status & GMR_FS_LEN) >> 16; + + if (status & GMR_FS_VLAN) + count -= VLAN_HLEN; /* Account for vlan tag */ + + netif_printk(sky2, rx_status, KERN_DEBUG, dev, + "rx slot %u status 0x%x len %d\n", + sky2->rx_next, status, length); + + sky2->rx_next = (sky2->rx_next + 1) % sky2->rx_pending; + prefetch(sky2->rx_ring + sky2->rx_next); + + /* This chip has hardware problems that generates bogus status. + * So do only marginal checking and expect higher level protocols + * to handle crap frames. + */ + if (sky2->hw->chip_id == CHIP_ID_YUKON_FE_P && + sky2->hw->chip_rev == CHIP_REV_YU_FE2_A0 && + length != count) + goto okay; + + if (status & GMR_FS_ANY_ERR) + goto error; + + if (!(status & GMR_FS_RX_OK)) + goto resubmit; + + /* if length reported by DMA does not match PHY, packet was truncated */ + if (length != count) + goto error; + +okay: + if (length < copybreak) + skb = receive_copy(sky2, re, length); + else + skb = receive_new(sky2, re, length); + + dev->stats.rx_dropped += (skb == NULL); + +resubmit: + sky2_rx_submit(sky2, re); + + return skb; + +error: + ++dev->stats.rx_errors; + + if (net_ratelimit()) + netif_info(sky2, rx_err, dev, + "rx error, status 0x%x length %d\n", status, length); + + goto resubmit; +} + +/* Transmit complete */ +static inline void sky2_tx_done(struct net_device *dev, u16 last) +{ + struct sky2_port *sky2 = netdev_priv(dev); + + if (netif_running(dev)) { + sky2_tx_complete(sky2, last); + + /* Wake unless it's detached, and called e.g. from sky2_down() */ + if (tx_avail(sky2) > MAX_SKB_TX_LE + 4) + netif_wake_queue(dev); + } +} + +static inline void sky2_skb_rx(const struct sky2_port *sky2, + u32 status, struct sk_buff *skb) +{ + if (status & GMR_FS_VLAN) + __vlan_hwaccel_put_tag(skb, be16_to_cpu(sky2->rx_tag)); + + if (skb->ip_summed == CHECKSUM_NONE) + netif_receive_skb(skb); + else + napi_gro_receive(&sky2->hw->napi, skb); +} + +static inline void sky2_rx_done(struct sky2_hw *hw, unsigned port, + unsigned packets, unsigned bytes) +{ + struct net_device *dev = hw->dev[port]; + struct sky2_port *sky2 = netdev_priv(dev); + + if (packets == 0) + return; + + u64_stats_update_begin(&sky2->rx_stats.syncp); + sky2->rx_stats.packets += packets; + sky2->rx_stats.bytes += bytes; + u64_stats_update_end(&sky2->rx_stats.syncp); + + dev->last_rx = jiffies; + sky2_rx_update(netdev_priv(dev), rxqaddr[port]); +} + +static void sky2_rx_checksum(struct sky2_port *sky2, u32 status) +{ + /* If this happens then driver assuming wrong format for chip type */ + BUG_ON(sky2->hw->flags & SKY2_HW_NEW_LE); + + /* Both checksum counters are programmed to start at + * the same offset, so unless there is a problem they + * should match. This failure is an early indication that + * hardware receive checksumming won't work. + */ + if (likely((u16)(status >> 16) == (u16)status)) { + struct sk_buff *skb = sky2->rx_ring[sky2->rx_next].skb; + skb->ip_summed = CHECKSUM_COMPLETE; + skb->csum = le16_to_cpu(status); + } else { + dev_notice(&sky2->hw->pdev->dev, + "%s: receive checksum problem (status = %#x)\n", + sky2->netdev->name, status); + + /* Disable checksum offload + * It will be reenabled on next ndo_set_features, but if it's + * really broken, will get disabled again + */ + sky2->netdev->features &= ~NETIF_F_RXCSUM; + sky2_write32(sky2->hw, Q_ADDR(rxqaddr[sky2->port], Q_CSR), + BMU_DIS_RX_CHKSUM); + } +} + +static void sky2_rx_hash(struct sky2_port *sky2, u32 status) +{ + struct sk_buff *skb; + + skb = sky2->rx_ring[sky2->rx_next].skb; + skb->rxhash = le32_to_cpu(status); +} + +/* Process status response ring */ +static int sky2_status_intr(struct sky2_hw *hw, int to_do, u16 idx) +{ + int work_done = 0; + unsigned int total_bytes[2] = { 0 }; + unsigned int total_packets[2] = { 0 }; + + rmb(); + do { + struct sky2_port *sky2; + struct sky2_status_le *le = hw->st_le + hw->st_idx; + unsigned port; + struct net_device *dev; + struct sk_buff *skb; + u32 status; + u16 length; + u8 opcode = le->opcode; + + if (!(opcode & HW_OWNER)) + break; + + hw->st_idx = RING_NEXT(hw->st_idx, hw->st_size); + + port = le->css & CSS_LINK_BIT; + dev = hw->dev[port]; + sky2 = netdev_priv(dev); + length = le16_to_cpu(le->length); + status = le32_to_cpu(le->status); + + le->opcode = 0; + switch (opcode & ~HW_OWNER) { + case OP_RXSTAT: + total_packets[port]++; + total_bytes[port] += length; + + skb = sky2_receive(dev, length, status); + if (!skb) + break; + + /* This chip reports checksum status differently */ + if (hw->flags & SKY2_HW_NEW_LE) { + if ((dev->features & NETIF_F_RXCSUM) && + (le->css & (CSS_ISIPV4 | CSS_ISIPV6)) && + (le->css & CSS_TCPUDPCSOK)) + skb->ip_summed = CHECKSUM_UNNECESSARY; + else + skb->ip_summed = CHECKSUM_NONE; + } + + skb->protocol = eth_type_trans(skb, dev); + + sky2_skb_rx(sky2, status, skb); + + /* Stop after net poll weight */ + if (++work_done >= to_do) + goto exit_loop; + break; + + case OP_RXVLAN: + sky2->rx_tag = length; + break; + + case OP_RXCHKSVLAN: + sky2->rx_tag = length; + /* fall through */ + case OP_RXCHKS: + if (likely(dev->features & NETIF_F_RXCSUM)) + sky2_rx_checksum(sky2, status); + break; + + case OP_RSS_HASH: + sky2_rx_hash(sky2, status); + break; + + case OP_TXINDEXLE: + /* TX index reports status for both ports */ + sky2_tx_done(hw->dev[0], status & 0xfff); + if (hw->dev[1]) + sky2_tx_done(hw->dev[1], + ((status >> 24) & 0xff) + | (u16)(length & 0xf) << 8); + break; + + default: + if (net_ratelimit()) + pr_warning("unknown status opcode 0x%x\n", opcode); + } + } while (hw->st_idx != idx); + + /* Fully processed status ring so clear irq */ + sky2_write32(hw, STAT_CTRL, SC_STAT_CLR_IRQ); + +exit_loop: + sky2_rx_done(hw, 0, total_packets[0], total_bytes[0]); + sky2_rx_done(hw, 1, total_packets[1], total_bytes[1]); + + return work_done; +} + +static void sky2_hw_error(struct sky2_hw *hw, unsigned port, u32 status) +{ + struct net_device *dev = hw->dev[port]; + + if (net_ratelimit()) + netdev_info(dev, "hw error interrupt status 0x%x\n", status); + + if (status & Y2_IS_PAR_RD1) { + if (net_ratelimit()) + netdev_err(dev, "ram data read parity error\n"); + /* Clear IRQ */ + sky2_write16(hw, RAM_BUFFER(port, B3_RI_CTRL), RI_CLR_RD_PERR); + } + + if (status & Y2_IS_PAR_WR1) { + if (net_ratelimit()) + netdev_err(dev, "ram data write parity error\n"); + + sky2_write16(hw, RAM_BUFFER(port, B3_RI_CTRL), RI_CLR_WR_PERR); + } + + if (status & Y2_IS_PAR_MAC1) { + if (net_ratelimit()) + netdev_err(dev, "MAC parity error\n"); + sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_CLI_TX_PE); + } + + if (status & Y2_IS_PAR_RX1) { + if (net_ratelimit()) + netdev_err(dev, "RX parity error\n"); + sky2_write32(hw, Q_ADDR(rxqaddr[port], Q_CSR), BMU_CLR_IRQ_PAR); + } + + if (status & Y2_IS_TCP_TXA1) { + if (net_ratelimit()) + netdev_err(dev, "TCP segmentation error\n"); + sky2_write32(hw, Q_ADDR(txqaddr[port], Q_CSR), BMU_CLR_IRQ_TCP); + } +} + +static void sky2_hw_intr(struct sky2_hw *hw) +{ + struct pci_dev *pdev = hw->pdev; + u32 status = sky2_read32(hw, B0_HWE_ISRC); + u32 hwmsk = sky2_read32(hw, B0_HWE_IMSK); + + status &= hwmsk; + + if (status & Y2_IS_TIST_OV) + sky2_write8(hw, GMAC_TI_ST_CTRL, GMT_ST_CLR_IRQ); + + if (status & (Y2_IS_MST_ERR | Y2_IS_IRQ_STAT)) { + u16 pci_err; + + sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON); + pci_err = sky2_pci_read16(hw, PCI_STATUS); + if (net_ratelimit()) + dev_err(&pdev->dev, "PCI hardware error (0x%x)\n", + pci_err); + + sky2_pci_write16(hw, PCI_STATUS, + pci_err | PCI_STATUS_ERROR_BITS); + sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF); + } + + if (status & Y2_IS_PCI_EXP) { + /* PCI-Express uncorrectable Error occurred */ + u32 err; + + sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON); + err = sky2_read32(hw, Y2_CFG_AER + PCI_ERR_UNCOR_STATUS); + sky2_write32(hw, Y2_CFG_AER + PCI_ERR_UNCOR_STATUS, + 0xfffffffful); + if (net_ratelimit()) + dev_err(&pdev->dev, "PCI Express error (0x%x)\n", err); + + sky2_read32(hw, Y2_CFG_AER + PCI_ERR_UNCOR_STATUS); + sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF); + } + + if (status & Y2_HWE_L1_MASK) + sky2_hw_error(hw, 0, status); + status >>= 8; + if (status & Y2_HWE_L1_MASK) + sky2_hw_error(hw, 1, status); +} + +static void sky2_mac_intr(struct sky2_hw *hw, unsigned port) +{ + struct net_device *dev = hw->dev[port]; + struct sky2_port *sky2 = netdev_priv(dev); + u8 status = sky2_read8(hw, SK_REG(port, GMAC_IRQ_SRC)); + + netif_info(sky2, intr, dev, "mac interrupt status 0x%x\n", status); + + if (status & GM_IS_RX_CO_OV) + gma_read16(hw, port, GM_RX_IRQ_SRC); + + if (status & GM_IS_TX_CO_OV) + gma_read16(hw, port, GM_TX_IRQ_SRC); + + if (status & GM_IS_RX_FF_OR) { + ++dev->stats.rx_fifo_errors; + sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_CLI_RX_FO); + } + + if (status & GM_IS_TX_FF_UR) { + ++dev->stats.tx_fifo_errors; + sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_CLI_TX_FU); + } +} + +/* This should never happen it is a bug. */ +static void sky2_le_error(struct sky2_hw *hw, unsigned port, u16 q) +{ + struct net_device *dev = hw->dev[port]; + u16 idx = sky2_read16(hw, Y2_QADDR(q, PREF_UNIT_GET_IDX)); + + dev_err(&hw->pdev->dev, "%s: descriptor error q=%#x get=%u put=%u\n", + dev->name, (unsigned) q, (unsigned) idx, + (unsigned) sky2_read16(hw, Y2_QADDR(q, PREF_UNIT_PUT_IDX))); + + sky2_write32(hw, Q_ADDR(q, Q_CSR), BMU_CLR_IRQ_CHK); +} + +static int sky2_rx_hung(struct net_device *dev) +{ + struct sky2_port *sky2 = netdev_priv(dev); + struct sky2_hw *hw = sky2->hw; + unsigned port = sky2->port; + unsigned rxq = rxqaddr[port]; + u32 mac_rp = sky2_read32(hw, SK_REG(port, RX_GMF_RP)); + u8 mac_lev = sky2_read8(hw, SK_REG(port, RX_GMF_RLEV)); + u8 fifo_rp = sky2_read8(hw, Q_ADDR(rxq, Q_RP)); + u8 fifo_lev = sky2_read8(hw, Q_ADDR(rxq, Q_RL)); + + /* If idle and MAC or PCI is stuck */ + if (sky2->check.last == dev->last_rx && + ((mac_rp == sky2->check.mac_rp && + mac_lev != 0 && mac_lev >= sky2->check.mac_lev) || + /* Check if the PCI RX hang */ + (fifo_rp == sky2->check.fifo_rp && + fifo_lev != 0 && fifo_lev >= sky2->check.fifo_lev))) { + netdev_printk(KERN_DEBUG, dev, + "hung mac %d:%d fifo %d (%d:%d)\n", + mac_lev, mac_rp, fifo_lev, + fifo_rp, sky2_read8(hw, Q_ADDR(rxq, Q_WP))); + return 1; + } else { + sky2->check.last = dev->last_rx; + sky2->check.mac_rp = mac_rp; + sky2->check.mac_lev = mac_lev; + sky2->check.fifo_rp = fifo_rp; + sky2->check.fifo_lev = fifo_lev; + return 0; + } +} + +static void sky2_watchdog(unsigned long arg) +{ + struct sky2_hw *hw = (struct sky2_hw *) arg; + + /* Check for lost IRQ once a second */ + if (sky2_read32(hw, B0_ISRC)) { + napi_schedule(&hw->napi); + } else { + int i, active = 0; + + for (i = 0; i < hw->ports; i++) { + struct net_device *dev = hw->dev[i]; + if (!netif_running(dev)) + continue; + ++active; + + /* For chips with Rx FIFO, check if stuck */ + if ((hw->flags & SKY2_HW_RAM_BUFFER) && + sky2_rx_hung(dev)) { + netdev_info(dev, "receiver hang detected\n"); + schedule_work(&hw->restart_work); + return; + } + } + + if (active == 0) + return; + } + + mod_timer(&hw->watchdog_timer, round_jiffies(jiffies + HZ)); +} + +/* Hardware/software error handling */ +static void sky2_err_intr(struct sky2_hw *hw, u32 status) +{ + if (net_ratelimit()) + dev_warn(&hw->pdev->dev, "error interrupt status=%#x\n", status); + + if (status & Y2_IS_HW_ERR) + sky2_hw_intr(hw); + + if (status & Y2_IS_IRQ_MAC1) + sky2_mac_intr(hw, 0); + + if (status & Y2_IS_IRQ_MAC2) + sky2_mac_intr(hw, 1); + + if (status & Y2_IS_CHK_RX1) + sky2_le_error(hw, 0, Q_R1); + + if (status & Y2_IS_CHK_RX2) + sky2_le_error(hw, 1, Q_R2); + + if (status & Y2_IS_CHK_TXA1) + sky2_le_error(hw, 0, Q_XA1); + + if (status & Y2_IS_CHK_TXA2) + sky2_le_error(hw, 1, Q_XA2); +} + +static int sky2_poll(struct napi_struct *napi, int work_limit) +{ + struct sky2_hw *hw = container_of(napi, struct sky2_hw, napi); + u32 status = sky2_read32(hw, B0_Y2_SP_EISR); + int work_done = 0; + u16 idx; + + if (unlikely(status & Y2_IS_ERROR)) + sky2_err_intr(hw, status); + + if (status & Y2_IS_IRQ_PHY1) + sky2_phy_intr(hw, 0); + + if (status & Y2_IS_IRQ_PHY2) + sky2_phy_intr(hw, 1); + + if (status & Y2_IS_PHY_QLNK) + sky2_qlink_intr(hw); + + while ((idx = sky2_read16(hw, STAT_PUT_IDX)) != hw->st_idx) { + work_done += sky2_status_intr(hw, work_limit - work_done, idx); + + if (work_done >= work_limit) + goto done; + } + + napi_complete(napi); + sky2_read32(hw, B0_Y2_SP_LISR); +done: + + return work_done; +} + +static irqreturn_t sky2_intr(int irq, void *dev_id) +{ + struct sky2_hw *hw = dev_id; + u32 status; + + /* Reading this mask interrupts as side effect */ + status = sky2_read32(hw, B0_Y2_SP_ISRC2); + if (status == 0 || status == ~0) + return IRQ_NONE; + + prefetch(&hw->st_le[hw->st_idx]); + + napi_schedule(&hw->napi); + + return IRQ_HANDLED; +} + +#ifdef CONFIG_NET_POLL_CONTROLLER +static void sky2_netpoll(struct net_device *dev) +{ + struct sky2_port *sky2 = netdev_priv(dev); + + napi_schedule(&sky2->hw->napi); +} +#endif + +/* Chip internal frequency for clock calculations */ +static u32 sky2_mhz(const struct sky2_hw *hw) +{ + switch (hw->chip_id) { + case CHIP_ID_YUKON_EC: + case CHIP_ID_YUKON_EC_U: + case CHIP_ID_YUKON_EX: + case CHIP_ID_YUKON_SUPR: + case CHIP_ID_YUKON_UL_2: + case CHIP_ID_YUKON_OPT: + case CHIP_ID_YUKON_PRM: + case CHIP_ID_YUKON_OP_2: + return 125; + + case CHIP_ID_YUKON_FE: + return 100; + + case CHIP_ID_YUKON_FE_P: + return 50; + + case CHIP_ID_YUKON_XL: + return 156; + + default: + BUG(); + } +} + +static inline u32 sky2_us2clk(const struct sky2_hw *hw, u32 us) +{ + return sky2_mhz(hw) * us; +} + +static inline u32 sky2_clk2us(const struct sky2_hw *hw, u32 clk) +{ + return clk / sky2_mhz(hw); +} + + +static int __devinit sky2_init(struct sky2_hw *hw) +{ + u8 t8; + + /* Enable all clocks and check for bad PCI access */ + sky2_pci_write32(hw, PCI_DEV_REG3, 0); + + sky2_write8(hw, B0_CTST, CS_RST_CLR); + + hw->chip_id = sky2_read8(hw, B2_CHIP_ID); + hw->chip_rev = (sky2_read8(hw, B2_MAC_CFG) & CFG_CHIP_R_MSK) >> 4; + + switch (hw->chip_id) { + case CHIP_ID_YUKON_XL: + hw->flags = SKY2_HW_GIGABIT | SKY2_HW_NEWER_PHY; + if (hw->chip_rev < CHIP_REV_YU_XL_A2) + hw->flags |= SKY2_HW_RSS_BROKEN; + break; + + case CHIP_ID_YUKON_EC_U: + hw->flags = SKY2_HW_GIGABIT + | SKY2_HW_NEWER_PHY + | SKY2_HW_ADV_POWER_CTL; + break; + + case CHIP_ID_YUKON_EX: + hw->flags = SKY2_HW_GIGABIT + | SKY2_HW_NEWER_PHY + | SKY2_HW_NEW_LE + | SKY2_HW_ADV_POWER_CTL + | SKY2_HW_RSS_CHKSUM; + + /* New transmit checksum */ + if (hw->chip_rev != CHIP_REV_YU_EX_B0) + hw->flags |= SKY2_HW_AUTO_TX_SUM; + break; + + case CHIP_ID_YUKON_EC: + /* This rev is really old, and requires untested workarounds */ + if (hw->chip_rev == CHIP_REV_YU_EC_A1) { + dev_err(&hw->pdev->dev, "unsupported revision Yukon-EC rev A1\n"); + return -EOPNOTSUPP; + } + hw->flags = SKY2_HW_GIGABIT | SKY2_HW_RSS_BROKEN; + break; + + case CHIP_ID_YUKON_FE: + hw->flags = SKY2_HW_RSS_BROKEN; + break; + + case CHIP_ID_YUKON_FE_P: + hw->flags = SKY2_HW_NEWER_PHY + | SKY2_HW_NEW_LE + | SKY2_HW_AUTO_TX_SUM + | SKY2_HW_ADV_POWER_CTL; + + /* The workaround for status conflicts VLAN tag detection. */ + if (hw->chip_rev == CHIP_REV_YU_FE2_A0) + hw->flags |= SKY2_HW_VLAN_BROKEN | SKY2_HW_RSS_CHKSUM; + break; + + case CHIP_ID_YUKON_SUPR: + hw->flags = SKY2_HW_GIGABIT + | SKY2_HW_NEWER_PHY + | SKY2_HW_NEW_LE + | SKY2_HW_AUTO_TX_SUM + | SKY2_HW_ADV_POWER_CTL; + + if (hw->chip_rev == CHIP_REV_YU_SU_A0) + hw->flags |= SKY2_HW_RSS_CHKSUM; + break; + + case CHIP_ID_YUKON_UL_2: + hw->flags = SKY2_HW_GIGABIT + | SKY2_HW_ADV_POWER_CTL; + break; + + case CHIP_ID_YUKON_OPT: + case CHIP_ID_YUKON_PRM: + case CHIP_ID_YUKON_OP_2: + hw->flags = SKY2_HW_GIGABIT + | SKY2_HW_NEW_LE + | SKY2_HW_ADV_POWER_CTL; + break; + + default: + dev_err(&hw->pdev->dev, "unsupported chip type 0x%x\n", + hw->chip_id); + return -EOPNOTSUPP; + } + + hw->pmd_type = sky2_read8(hw, B2_PMD_TYP); + if (hw->pmd_type == 'L' || hw->pmd_type == 'S' || hw->pmd_type == 'P') + hw->flags |= SKY2_HW_FIBRE_PHY; + + hw->ports = 1; + t8 = sky2_read8(hw, B2_Y2_HW_RES); + if ((t8 & CFG_DUAL_MAC_MSK) == CFG_DUAL_MAC_MSK) { + if (!(sky2_read8(hw, B2_Y2_CLK_GATE) & Y2_STATUS_LNK2_INAC)) + ++hw->ports; + } + + if (sky2_read8(hw, B2_E_0)) + hw->flags |= SKY2_HW_RAM_BUFFER; + + return 0; +} + +static void sky2_reset(struct sky2_hw *hw) +{ + struct pci_dev *pdev = hw->pdev; + u16 status; + int i; + u32 hwe_mask = Y2_HWE_ALL_MASK; + + /* disable ASF */ + if (hw->chip_id == CHIP_ID_YUKON_EX + || hw->chip_id == CHIP_ID_YUKON_SUPR) { + sky2_write32(hw, CPU_WDOG, 0); + status = sky2_read16(hw, HCU_CCSR); + status &= ~(HCU_CCSR_AHB_RST | HCU_CCSR_CPU_RST_MODE | + HCU_CCSR_UC_STATE_MSK); + /* + * CPU clock divider shouldn't be used because + * - ASF firmware may malfunction + * - Yukon-Supreme: Parallel FLASH doesn't support divided clocks + */ + status &= ~HCU_CCSR_CPU_CLK_DIVIDE_MSK; + sky2_write16(hw, HCU_CCSR, status); + sky2_write32(hw, CPU_WDOG, 0); + } else + sky2_write8(hw, B28_Y2_ASF_STAT_CMD, Y2_ASF_RESET); + sky2_write16(hw, B0_CTST, Y2_ASF_DISABLE); + + /* do a SW reset */ + sky2_write8(hw, B0_CTST, CS_RST_SET); + sky2_write8(hw, B0_CTST, CS_RST_CLR); + + /* allow writes to PCI config */ + sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON); + + /* clear PCI errors, if any */ + status = sky2_pci_read16(hw, PCI_STATUS); + status |= PCI_STATUS_ERROR_BITS; + sky2_pci_write16(hw, PCI_STATUS, status); + + sky2_write8(hw, B0_CTST, CS_MRST_CLR); + + if (pci_is_pcie(pdev)) { + sky2_write32(hw, Y2_CFG_AER + PCI_ERR_UNCOR_STATUS, + 0xfffffffful); + + /* If error bit is stuck on ignore it */ + if (sky2_read32(hw, B0_HWE_ISRC) & Y2_IS_PCI_EXP) + dev_info(&pdev->dev, "ignoring stuck error report bit\n"); + else + hwe_mask |= Y2_IS_PCI_EXP; + } + + sky2_power_on(hw); + sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF); + + for (i = 0; i < hw->ports; i++) { + sky2_write8(hw, SK_REG(i, GMAC_LINK_CTRL), GMLC_RST_SET); + sky2_write8(hw, SK_REG(i, GMAC_LINK_CTRL), GMLC_RST_CLR); + + if (hw->chip_id == CHIP_ID_YUKON_EX || + hw->chip_id == CHIP_ID_YUKON_SUPR) + sky2_write16(hw, SK_REG(i, GMAC_CTRL), + GMC_BYP_MACSECRX_ON | GMC_BYP_MACSECTX_ON + | GMC_BYP_RETR_ON); + + } + + if (hw->chip_id == CHIP_ID_YUKON_SUPR && hw->chip_rev > CHIP_REV_YU_SU_B0) { + /* enable MACSec clock gating */ + sky2_pci_write32(hw, PCI_DEV_REG3, P_CLK_MACSEC_DIS); + } + + if (hw->chip_id == CHIP_ID_YUKON_OPT || + hw->chip_id == CHIP_ID_YUKON_PRM || + hw->chip_id == CHIP_ID_YUKON_OP_2) { + u16 reg; + u32 msk; + + if (hw->chip_id == CHIP_ID_YUKON_OPT && hw->chip_rev == 0) { + /* disable PCI-E PHY power down (set PHY reg 0x80, bit 7 */ + sky2_write32(hw, Y2_PEX_PHY_DATA, (0x80UL << 16) | (1 << 7)); + + /* set PHY Link Detect Timer to 1.1 second (11x 100ms) */ + reg = 10; + + /* re-enable PEX PM in PEX PHY debug reg. 8 (clear bit 12) */ + sky2_write32(hw, Y2_PEX_PHY_DATA, PEX_DB_ACCESS | (0x08UL << 16)); + } else { + /* set PHY Link Detect Timer to 0.4 second (4x 100ms) */ + reg = 3; + } + + reg <<= PSM_CONFIG_REG4_TIMER_PHY_LINK_DETECT_BASE; + reg |= PSM_CONFIG_REG4_RST_PHY_LINK_DETECT; + + /* reset PHY Link Detect */ + sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON); + sky2_pci_write16(hw, PSM_CONFIG_REG4, reg); + + /* enable PHY Quick Link */ + msk = sky2_read32(hw, B0_IMSK); + msk |= Y2_IS_PHY_QLNK; + sky2_write32(hw, B0_IMSK, msk); + + /* check if PSMv2 was running before */ + reg = sky2_pci_read16(hw, PSM_CONFIG_REG3); + if (reg & PCI_EXP_LNKCTL_ASPMC) + /* restore the PCIe Link Control register */ + sky2_pci_write16(hw, pdev->pcie_cap + PCI_EXP_LNKCTL, + reg); + + sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF); + + /* re-enable PEX PM in PEX PHY debug reg. 8 (clear bit 12) */ + sky2_write32(hw, Y2_PEX_PHY_DATA, PEX_DB_ACCESS | (0x08UL << 16)); + } + + /* Clear I2C IRQ noise */ + sky2_write32(hw, B2_I2C_IRQ, 1); + + /* turn off hardware timer (unused) */ + sky2_write8(hw, B2_TI_CTRL, TIM_STOP); + sky2_write8(hw, B2_TI_CTRL, TIM_CLR_IRQ); + + /* Turn off descriptor polling */ + sky2_write32(hw, B28_DPT_CTRL, DPT_STOP); + + /* Turn off receive timestamp */ + sky2_write8(hw, GMAC_TI_ST_CTRL, GMT_ST_STOP); + sky2_write8(hw, GMAC_TI_ST_CTRL, GMT_ST_CLR_IRQ); + + /* enable the Tx Arbiters */ + for (i = 0; i < hw->ports; i++) + sky2_write8(hw, SK_REG(i, TXA_CTRL), TXA_ENA_ARB); + + /* Initialize ram interface */ + for (i = 0; i < hw->ports; i++) { + sky2_write8(hw, RAM_BUFFER(i, B3_RI_CTRL), RI_RST_CLR); + + sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_R1), SK_RI_TO_53); + sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_XA1), SK_RI_TO_53); + sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_XS1), SK_RI_TO_53); + sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_R1), SK_RI_TO_53); + sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_XA1), SK_RI_TO_53); + sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_XS1), SK_RI_TO_53); + sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_R2), SK_RI_TO_53); + sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_XA2), SK_RI_TO_53); + sky2_write8(hw, RAM_BUFFER(i, B3_RI_WTO_XS2), SK_RI_TO_53); + sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_R2), SK_RI_TO_53); + sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_XA2), SK_RI_TO_53); + sky2_write8(hw, RAM_BUFFER(i, B3_RI_RTO_XS2), SK_RI_TO_53); + } + + sky2_write32(hw, B0_HWE_IMSK, hwe_mask); + + for (i = 0; i < hw->ports; i++) + sky2_gmac_reset(hw, i); + + memset(hw->st_le, 0, hw->st_size * sizeof(struct sky2_status_le)); + hw->st_idx = 0; + + sky2_write32(hw, STAT_CTRL, SC_STAT_RST_SET); + sky2_write32(hw, STAT_CTRL, SC_STAT_RST_CLR); + + sky2_write32(hw, STAT_LIST_ADDR_LO, hw->st_dma); + sky2_write32(hw, STAT_LIST_ADDR_HI, (u64) hw->st_dma >> 32); + + /* Set the list last index */ + sky2_write16(hw, STAT_LAST_IDX, hw->st_size - 1); + + sky2_write16(hw, STAT_TX_IDX_TH, 10); + sky2_write8(hw, STAT_FIFO_WM, 16); + + /* set Status-FIFO ISR watermark */ + if (hw->chip_id == CHIP_ID_YUKON_XL && hw->chip_rev == 0) + sky2_write8(hw, STAT_FIFO_ISR_WM, 4); + else + sky2_write8(hw, STAT_FIFO_ISR_WM, 16); + + sky2_write32(hw, STAT_TX_TIMER_INI, sky2_us2clk(hw, 1000)); + sky2_write32(hw, STAT_ISR_TIMER_INI, sky2_us2clk(hw, 20)); + sky2_write32(hw, STAT_LEV_TIMER_INI, sky2_us2clk(hw, 100)); + + /* enable status unit */ + sky2_write32(hw, STAT_CTRL, SC_STAT_OP_ON); + + sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_START); + sky2_write8(hw, STAT_LEV_TIMER_CTRL, TIM_START); + sky2_write8(hw, STAT_ISR_TIMER_CTRL, TIM_START); +} + +/* Take device down (offline). + * Equivalent to doing dev_stop() but this does not + * inform upper layers of the transition. + */ +static void sky2_detach(struct net_device *dev) +{ + if (netif_running(dev)) { + netif_tx_lock(dev); + netif_device_detach(dev); /* stop txq */ + netif_tx_unlock(dev); + sky2_down(dev); + } +} + +/* Bring device back after doing sky2_detach */ +static int sky2_reattach(struct net_device *dev) +{ + int err = 0; + + if (netif_running(dev)) { + err = sky2_up(dev); + if (err) { + netdev_info(dev, "could not restart %d\n", err); + dev_close(dev); + } else { + netif_device_attach(dev); + sky2_set_multicast(dev); + } + } + + return err; +} + +static void sky2_all_down(struct sky2_hw *hw) +{ + int i; + + sky2_read32(hw, B0_IMSK); + sky2_write32(hw, B0_IMSK, 0); + synchronize_irq(hw->pdev->irq); + napi_disable(&hw->napi); + + for (i = 0; i < hw->ports; i++) { + struct net_device *dev = hw->dev[i]; + struct sky2_port *sky2 = netdev_priv(dev); + + if (!netif_running(dev)) + continue; + + netif_carrier_off(dev); + netif_tx_disable(dev); + sky2_hw_down(sky2); + } +} + +static void sky2_all_up(struct sky2_hw *hw) +{ + u32 imask = Y2_IS_BASE; + int i; + + for (i = 0; i < hw->ports; i++) { + struct net_device *dev = hw->dev[i]; + struct sky2_port *sky2 = netdev_priv(dev); + + if (!netif_running(dev)) + continue; + + sky2_hw_up(sky2); + sky2_set_multicast(dev); + imask |= portirq_msk[i]; + netif_wake_queue(dev); + } + + sky2_write32(hw, B0_IMSK, imask); + sky2_read32(hw, B0_IMSK); + + sky2_read32(hw, B0_Y2_SP_LISR); + napi_enable(&hw->napi); +} + +static void sky2_restart(struct work_struct *work) +{ + struct sky2_hw *hw = container_of(work, struct sky2_hw, restart_work); + + rtnl_lock(); + + sky2_all_down(hw); + sky2_reset(hw); + sky2_all_up(hw); + + rtnl_unlock(); +} + +static inline u8 sky2_wol_supported(const struct sky2_hw *hw) +{ + return sky2_is_copper(hw) ? (WAKE_PHY | WAKE_MAGIC) : 0; +} + +static void sky2_get_wol(struct net_device *dev, struct ethtool_wolinfo *wol) +{ + const struct sky2_port *sky2 = netdev_priv(dev); + + wol->supported = sky2_wol_supported(sky2->hw); + wol->wolopts = sky2->wol; +} + +static int sky2_set_wol(struct net_device *dev, struct ethtool_wolinfo *wol) +{ + struct sky2_port *sky2 = netdev_priv(dev); + struct sky2_hw *hw = sky2->hw; + bool enable_wakeup = false; + int i; + + if ((wol->wolopts & ~sky2_wol_supported(sky2->hw)) || + !device_can_wakeup(&hw->pdev->dev)) + return -EOPNOTSUPP; + + sky2->wol = wol->wolopts; + + for (i = 0; i < hw->ports; i++) { + struct net_device *dev = hw->dev[i]; + struct sky2_port *sky2 = netdev_priv(dev); + + if (sky2->wol) + enable_wakeup = true; + } + device_set_wakeup_enable(&hw->pdev->dev, enable_wakeup); + + return 0; +} + +static u32 sky2_supported_modes(const struct sky2_hw *hw) +{ + if (sky2_is_copper(hw)) { + u32 modes = SUPPORTED_10baseT_Half + | SUPPORTED_10baseT_Full + | SUPPORTED_100baseT_Half + | SUPPORTED_100baseT_Full; + + if (hw->flags & SKY2_HW_GIGABIT) + modes |= SUPPORTED_1000baseT_Half + | SUPPORTED_1000baseT_Full; + return modes; + } else + return SUPPORTED_1000baseT_Half + | SUPPORTED_1000baseT_Full; +} + +static int sky2_get_settings(struct net_device *dev, struct ethtool_cmd *ecmd) +{ + struct sky2_port *sky2 = netdev_priv(dev); + struct sky2_hw *hw = sky2->hw; + + ecmd->transceiver = XCVR_INTERNAL; + ecmd->supported = sky2_supported_modes(hw); + ecmd->phy_address = PHY_ADDR_MARV; + if (sky2_is_copper(hw)) { + ecmd->port = PORT_TP; + ethtool_cmd_speed_set(ecmd, sky2->speed); + ecmd->supported |= SUPPORTED_Autoneg | SUPPORTED_TP; + } else { + ethtool_cmd_speed_set(ecmd, SPEED_1000); + ecmd->port = PORT_FIBRE; + ecmd->supported |= SUPPORTED_Autoneg | SUPPORTED_FIBRE; + } + + ecmd->advertising = sky2->advertising; + ecmd->autoneg = (sky2->flags & SKY2_FLAG_AUTO_SPEED) + ? AUTONEG_ENABLE : AUTONEG_DISABLE; + ecmd->duplex = sky2->duplex; + return 0; +} + +static int sky2_set_settings(struct net_device *dev, struct ethtool_cmd *ecmd) +{ + struct sky2_port *sky2 = netdev_priv(dev); + const struct sky2_hw *hw = sky2->hw; + u32 supported = sky2_supported_modes(hw); + + if (ecmd->autoneg == AUTONEG_ENABLE) { + if (ecmd->advertising & ~supported) + return -EINVAL; + + if (sky2_is_copper(hw)) + sky2->advertising = ecmd->advertising | + ADVERTISED_TP | + ADVERTISED_Autoneg; + else + sky2->advertising = ecmd->advertising | + ADVERTISED_FIBRE | + ADVERTISED_Autoneg; + + sky2->flags |= SKY2_FLAG_AUTO_SPEED; + sky2->duplex = -1; + sky2->speed = -1; + } else { + u32 setting; + u32 speed = ethtool_cmd_speed(ecmd); + + switch (speed) { + case SPEED_1000: + if (ecmd->duplex == DUPLEX_FULL) + setting = SUPPORTED_1000baseT_Full; + else if (ecmd->duplex == DUPLEX_HALF) + setting = SUPPORTED_1000baseT_Half; + else + return -EINVAL; + break; + case SPEED_100: + if (ecmd->duplex == DUPLEX_FULL) + setting = SUPPORTED_100baseT_Full; + else if (ecmd->duplex == DUPLEX_HALF) + setting = SUPPORTED_100baseT_Half; + else + return -EINVAL; + break; + + case SPEED_10: + if (ecmd->duplex == DUPLEX_FULL) + setting = SUPPORTED_10baseT_Full; + else if (ecmd->duplex == DUPLEX_HALF) + setting = SUPPORTED_10baseT_Half; + else + return -EINVAL; + break; + default: + return -EINVAL; + } + + if ((setting & supported) == 0) + return -EINVAL; + + sky2->speed = speed; + sky2->duplex = ecmd->duplex; + sky2->flags &= ~SKY2_FLAG_AUTO_SPEED; + } + + if (netif_running(dev)) { + sky2_phy_reinit(sky2); + sky2_set_multicast(dev); + } + + return 0; +} + +static void sky2_get_drvinfo(struct net_device *dev, + struct ethtool_drvinfo *info) +{ + struct sky2_port *sky2 = netdev_priv(dev); + + strcpy(info->driver, DRV_NAME); + strcpy(info->version, DRV_VERSION); + strcpy(info->fw_version, "N/A"); + strcpy(info->bus_info, pci_name(sky2->hw->pdev)); +} + +static const struct sky2_stat { + char name[ETH_GSTRING_LEN]; + u16 offset; +} sky2_stats[] = { + { "tx_bytes", GM_TXO_OK_HI }, + { "rx_bytes", GM_RXO_OK_HI }, + { "tx_broadcast", GM_TXF_BC_OK }, + { "rx_broadcast", GM_RXF_BC_OK }, + { "tx_multicast", GM_TXF_MC_OK }, + { "rx_multicast", GM_RXF_MC_OK }, + { "tx_unicast", GM_TXF_UC_OK }, + { "rx_unicast", GM_RXF_UC_OK }, + { "tx_mac_pause", GM_TXF_MPAUSE }, + { "rx_mac_pause", GM_RXF_MPAUSE }, + { "collisions", GM_TXF_COL }, + { "late_collision",GM_TXF_LAT_COL }, + { "aborted", GM_TXF_ABO_COL }, + { "single_collisions", GM_TXF_SNG_COL }, + { "multi_collisions", GM_TXF_MUL_COL }, + + { "rx_short", GM_RXF_SHT }, + { "rx_runt", GM_RXE_FRAG }, + { "rx_64_byte_packets", GM_RXF_64B }, + { "rx_65_to_127_byte_packets", GM_RXF_127B }, + { "rx_128_to_255_byte_packets", GM_RXF_255B }, + { "rx_256_to_511_byte_packets", GM_RXF_511B }, + { "rx_512_to_1023_byte_packets", GM_RXF_1023B }, + { "rx_1024_to_1518_byte_packets", GM_RXF_1518B }, + { "rx_1518_to_max_byte_packets", GM_RXF_MAX_SZ }, + { "rx_too_long", GM_RXF_LNG_ERR }, + { "rx_fifo_overflow", GM_RXE_FIFO_OV }, + { "rx_jabber", GM_RXF_JAB_PKT }, + { "rx_fcs_error", GM_RXF_FCS_ERR }, + + { "tx_64_byte_packets", GM_TXF_64B }, + { "tx_65_to_127_byte_packets", GM_TXF_127B }, + { "tx_128_to_255_byte_packets", GM_TXF_255B }, + { "tx_256_to_511_byte_packets", GM_TXF_511B }, + { "tx_512_to_1023_byte_packets", GM_TXF_1023B }, + { "tx_1024_to_1518_byte_packets", GM_TXF_1518B }, + { "tx_1519_to_max_byte_packets", GM_TXF_MAX_SZ }, + { "tx_fifo_underrun", GM_TXE_FIFO_UR }, +}; + +static u32 sky2_get_msglevel(struct net_device *netdev) +{ + struct sky2_port *sky2 = netdev_priv(netdev); + return sky2->msg_enable; +} + +static int sky2_nway_reset(struct net_device *dev) +{ + struct sky2_port *sky2 = netdev_priv(dev); + + if (!netif_running(dev) || !(sky2->flags & SKY2_FLAG_AUTO_SPEED)) + return -EINVAL; + + sky2_phy_reinit(sky2); + sky2_set_multicast(dev); + + return 0; +} + +static void sky2_phy_stats(struct sky2_port *sky2, u64 * data, unsigned count) +{ + struct sky2_hw *hw = sky2->hw; + unsigned port = sky2->port; + int i; + + data[0] = get_stats64(hw, port, GM_TXO_OK_LO); + data[1] = get_stats64(hw, port, GM_RXO_OK_LO); + + for (i = 2; i < count; i++) + data[i] = get_stats32(hw, port, sky2_stats[i].offset); +} + +static void sky2_set_msglevel(struct net_device *netdev, u32 value) +{ + struct sky2_port *sky2 = netdev_priv(netdev); + sky2->msg_enable = value; +} + +static int sky2_get_sset_count(struct net_device *dev, int sset) +{ + switch (sset) { + case ETH_SS_STATS: + return ARRAY_SIZE(sky2_stats); + default: + return -EOPNOTSUPP; + } +} + +static void sky2_get_ethtool_stats(struct net_device *dev, + struct ethtool_stats *stats, u64 * data) +{ + struct sky2_port *sky2 = netdev_priv(dev); + + sky2_phy_stats(sky2, data, ARRAY_SIZE(sky2_stats)); +} + +static void sky2_get_strings(struct net_device *dev, u32 stringset, u8 * data) +{ + int i; + + switch (stringset) { + case ETH_SS_STATS: + for (i = 0; i < ARRAY_SIZE(sky2_stats); i++) + memcpy(data + i * ETH_GSTRING_LEN, + sky2_stats[i].name, ETH_GSTRING_LEN); + break; + } +} + +static int sky2_set_mac_address(struct net_device *dev, void *p) +{ + struct sky2_port *sky2 = netdev_priv(dev); + struct sky2_hw *hw = sky2->hw; + unsigned port = sky2->port; + const struct sockaddr *addr = p; + + if (!is_valid_ether_addr(addr->sa_data)) + return -EADDRNOTAVAIL; + + memcpy(dev->dev_addr, addr->sa_data, ETH_ALEN); + memcpy_toio(hw->regs + B2_MAC_1 + port * 8, + dev->dev_addr, ETH_ALEN); + memcpy_toio(hw->regs + B2_MAC_2 + port * 8, + dev->dev_addr, ETH_ALEN); + + /* virtual address for data */ + gma_set_addr(hw, port, GM_SRC_ADDR_2L, dev->dev_addr); + + /* physical address: used for pause frames */ + gma_set_addr(hw, port, GM_SRC_ADDR_1L, dev->dev_addr); + + return 0; +} + +static inline void sky2_add_filter(u8 filter[8], const u8 *addr) +{ + u32 bit; + + bit = ether_crc(ETH_ALEN, addr) & 63; + filter[bit >> 3] |= 1 << (bit & 7); +} + +static void sky2_set_multicast(struct net_device *dev) +{ + struct sky2_port *sky2 = netdev_priv(dev); + struct sky2_hw *hw = sky2->hw; + unsigned port = sky2->port; + struct netdev_hw_addr *ha; + u16 reg; + u8 filter[8]; + int rx_pause; + static const u8 pause_mc_addr[ETH_ALEN] = { 0x1, 0x80, 0xc2, 0x0, 0x0, 0x1 }; + + rx_pause = (sky2->flow_status == FC_RX || sky2->flow_status == FC_BOTH); + memset(filter, 0, sizeof(filter)); + + reg = gma_read16(hw, port, GM_RX_CTRL); + reg |= GM_RXCR_UCF_ENA; + + if (dev->flags & IFF_PROMISC) /* promiscuous */ + reg &= ~(GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA); + else if (dev->flags & IFF_ALLMULTI) + memset(filter, 0xff, sizeof(filter)); + else if (netdev_mc_empty(dev) && !rx_pause) + reg &= ~GM_RXCR_MCF_ENA; + else { + reg |= GM_RXCR_MCF_ENA; + + if (rx_pause) + sky2_add_filter(filter, pause_mc_addr); + + netdev_for_each_mc_addr(ha, dev) + sky2_add_filter(filter, ha->addr); + } + + gma_write16(hw, port, GM_MC_ADDR_H1, + (u16) filter[0] | ((u16) filter[1] << 8)); + gma_write16(hw, port, GM_MC_ADDR_H2, + (u16) filter[2] | ((u16) filter[3] << 8)); + gma_write16(hw, port, GM_MC_ADDR_H3, + (u16) filter[4] | ((u16) filter[5] << 8)); + gma_write16(hw, port, GM_MC_ADDR_H4, + (u16) filter[6] | ((u16) filter[7] << 8)); + + gma_write16(hw, port, GM_RX_CTRL, reg); +} + +static struct rtnl_link_stats64 *sky2_get_stats(struct net_device *dev, + struct rtnl_link_stats64 *stats) +{ + struct sky2_port *sky2 = netdev_priv(dev); + struct sky2_hw *hw = sky2->hw; + unsigned port = sky2->port; + unsigned int start; + u64 _bytes, _packets; + + do { + start = u64_stats_fetch_begin_bh(&sky2->rx_stats.syncp); + _bytes = sky2->rx_stats.bytes; + _packets = sky2->rx_stats.packets; + } while (u64_stats_fetch_retry_bh(&sky2->rx_stats.syncp, start)); + + stats->rx_packets = _packets; + stats->rx_bytes = _bytes; + + do { + start = u64_stats_fetch_begin_bh(&sky2->tx_stats.syncp); + _bytes = sky2->tx_stats.bytes; + _packets = sky2->tx_stats.packets; + } while (u64_stats_fetch_retry_bh(&sky2->tx_stats.syncp, start)); + + stats->tx_packets = _packets; + stats->tx_bytes = _bytes; + + stats->multicast = get_stats32(hw, port, GM_RXF_MC_OK) + + get_stats32(hw, port, GM_RXF_BC_OK); + + stats->collisions = get_stats32(hw, port, GM_TXF_COL); + + stats->rx_length_errors = get_stats32(hw, port, GM_RXF_LNG_ERR); + stats->rx_crc_errors = get_stats32(hw, port, GM_RXF_FCS_ERR); + stats->rx_frame_errors = get_stats32(hw, port, GM_RXF_SHT) + + get_stats32(hw, port, GM_RXE_FRAG); + stats->rx_over_errors = get_stats32(hw, port, GM_RXE_FIFO_OV); + + stats->rx_dropped = dev->stats.rx_dropped; + stats->rx_fifo_errors = dev->stats.rx_fifo_errors; + stats->tx_fifo_errors = dev->stats.tx_fifo_errors; + + return stats; +} + +/* Can have one global because blinking is controlled by + * ethtool and that is always under RTNL mutex + */ +static void sky2_led(struct sky2_port *sky2, enum led_mode mode) +{ + struct sky2_hw *hw = sky2->hw; + unsigned port = sky2->port; + + spin_lock_bh(&sky2->phy_lock); + if (hw->chip_id == CHIP_ID_YUKON_EC_U || + hw->chip_id == CHIP_ID_YUKON_EX || + hw->chip_id == CHIP_ID_YUKON_SUPR) { + u16 pg; + pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR); + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3); + + switch (mode) { + case MO_LED_OFF: + gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, + PHY_M_LEDC_LOS_CTRL(8) | + PHY_M_LEDC_INIT_CTRL(8) | + PHY_M_LEDC_STA1_CTRL(8) | + PHY_M_LEDC_STA0_CTRL(8)); + break; + case MO_LED_ON: + gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, + PHY_M_LEDC_LOS_CTRL(9) | + PHY_M_LEDC_INIT_CTRL(9) | + PHY_M_LEDC_STA1_CTRL(9) | + PHY_M_LEDC_STA0_CTRL(9)); + break; + case MO_LED_BLINK: + gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, + PHY_M_LEDC_LOS_CTRL(0xa) | + PHY_M_LEDC_INIT_CTRL(0xa) | + PHY_M_LEDC_STA1_CTRL(0xa) | + PHY_M_LEDC_STA0_CTRL(0xa)); + break; + case MO_LED_NORM: + gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, + PHY_M_LEDC_LOS_CTRL(1) | + PHY_M_LEDC_INIT_CTRL(8) | + PHY_M_LEDC_STA1_CTRL(7) | + PHY_M_LEDC_STA0_CTRL(7)); + } + + gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg); + } else + gm_phy_write(hw, port, PHY_MARV_LED_OVER, + PHY_M_LED_MO_DUP(mode) | + PHY_M_LED_MO_10(mode) | + PHY_M_LED_MO_100(mode) | + PHY_M_LED_MO_1000(mode) | + PHY_M_LED_MO_RX(mode) | + PHY_M_LED_MO_TX(mode)); + + spin_unlock_bh(&sky2->phy_lock); +} + +/* blink LED's for finding board */ +static int sky2_set_phys_id(struct net_device *dev, + enum ethtool_phys_id_state state) +{ + struct sky2_port *sky2 = netdev_priv(dev); + + switch (state) { + case ETHTOOL_ID_ACTIVE: + return 1; /* cycle on/off once per second */ + case ETHTOOL_ID_INACTIVE: + sky2_led(sky2, MO_LED_NORM); + break; + case ETHTOOL_ID_ON: + sky2_led(sky2, MO_LED_ON); + break; + case ETHTOOL_ID_OFF: + sky2_led(sky2, MO_LED_OFF); + break; + } + + return 0; +} + +static void sky2_get_pauseparam(struct net_device *dev, + struct ethtool_pauseparam *ecmd) +{ + struct sky2_port *sky2 = netdev_priv(dev); + + switch (sky2->flow_mode) { + case FC_NONE: + ecmd->tx_pause = ecmd->rx_pause = 0; + break; + case FC_TX: + ecmd->tx_pause = 1, ecmd->rx_pause = 0; + break; + case FC_RX: + ecmd->tx_pause = 0, ecmd->rx_pause = 1; + break; + case FC_BOTH: + ecmd->tx_pause = ecmd->rx_pause = 1; + } + + ecmd->autoneg = (sky2->flags & SKY2_FLAG_AUTO_PAUSE) + ? AUTONEG_ENABLE : AUTONEG_DISABLE; +} + +static int sky2_set_pauseparam(struct net_device *dev, + struct ethtool_pauseparam *ecmd) +{ + struct sky2_port *sky2 = netdev_priv(dev); + + if (ecmd->autoneg == AUTONEG_ENABLE) + sky2->flags |= SKY2_FLAG_AUTO_PAUSE; + else + sky2->flags &= ~SKY2_FLAG_AUTO_PAUSE; + + sky2->flow_mode = sky2_flow(ecmd->rx_pause, ecmd->tx_pause); + + if (netif_running(dev)) + sky2_phy_reinit(sky2); + + return 0; +} + +static int sky2_get_coalesce(struct net_device *dev, + struct ethtool_coalesce *ecmd) +{ + struct sky2_port *sky2 = netdev_priv(dev); + struct sky2_hw *hw = sky2->hw; + + if (sky2_read8(hw, STAT_TX_TIMER_CTRL) == TIM_STOP) + ecmd->tx_coalesce_usecs = 0; + else { + u32 clks = sky2_read32(hw, STAT_TX_TIMER_INI); + ecmd->tx_coalesce_usecs = sky2_clk2us(hw, clks); + } + ecmd->tx_max_coalesced_frames = sky2_read16(hw, STAT_TX_IDX_TH); + + if (sky2_read8(hw, STAT_LEV_TIMER_CTRL) == TIM_STOP) + ecmd->rx_coalesce_usecs = 0; + else { + u32 clks = sky2_read32(hw, STAT_LEV_TIMER_INI); + ecmd->rx_coalesce_usecs = sky2_clk2us(hw, clks); + } + ecmd->rx_max_coalesced_frames = sky2_read8(hw, STAT_FIFO_WM); + + if (sky2_read8(hw, STAT_ISR_TIMER_CTRL) == TIM_STOP) + ecmd->rx_coalesce_usecs_irq = 0; + else { + u32 clks = sky2_read32(hw, STAT_ISR_TIMER_INI); + ecmd->rx_coalesce_usecs_irq = sky2_clk2us(hw, clks); + } + + ecmd->rx_max_coalesced_frames_irq = sky2_read8(hw, STAT_FIFO_ISR_WM); + + return 0; +} + +/* Note: this affect both ports */ +static int sky2_set_coalesce(struct net_device *dev, + struct ethtool_coalesce *ecmd) +{ + struct sky2_port *sky2 = netdev_priv(dev); + struct sky2_hw *hw = sky2->hw; + const u32 tmax = sky2_clk2us(hw, 0x0ffffff); + + if (ecmd->tx_coalesce_usecs > tmax || + ecmd->rx_coalesce_usecs > tmax || + ecmd->rx_coalesce_usecs_irq > tmax) + return -EINVAL; + + if (ecmd->tx_max_coalesced_frames >= sky2->tx_ring_size-1) + return -EINVAL; + if (ecmd->rx_max_coalesced_frames > RX_MAX_PENDING) + return -EINVAL; + if (ecmd->rx_max_coalesced_frames_irq > RX_MAX_PENDING) + return -EINVAL; + + if (ecmd->tx_coalesce_usecs == 0) + sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_STOP); + else { + sky2_write32(hw, STAT_TX_TIMER_INI, + sky2_us2clk(hw, ecmd->tx_coalesce_usecs)); + sky2_write8(hw, STAT_TX_TIMER_CTRL, TIM_START); + } + sky2_write16(hw, STAT_TX_IDX_TH, ecmd->tx_max_coalesced_frames); + + if (ecmd->rx_coalesce_usecs == 0) + sky2_write8(hw, STAT_LEV_TIMER_CTRL, TIM_STOP); + else { + sky2_write32(hw, STAT_LEV_TIMER_INI, + sky2_us2clk(hw, ecmd->rx_coalesce_usecs)); + sky2_write8(hw, STAT_LEV_TIMER_CTRL, TIM_START); + } + sky2_write8(hw, STAT_FIFO_WM, ecmd->rx_max_coalesced_frames); + + if (ecmd->rx_coalesce_usecs_irq == 0) + sky2_write8(hw, STAT_ISR_TIMER_CTRL, TIM_STOP); + else { + sky2_write32(hw, STAT_ISR_TIMER_INI, + sky2_us2clk(hw, ecmd->rx_coalesce_usecs_irq)); + sky2_write8(hw, STAT_ISR_TIMER_CTRL, TIM_START); + } + sky2_write8(hw, STAT_FIFO_ISR_WM, ecmd->rx_max_coalesced_frames_irq); + return 0; +} + +static void sky2_get_ringparam(struct net_device *dev, + struct ethtool_ringparam *ering) +{ + struct sky2_port *sky2 = netdev_priv(dev); + + ering->rx_max_pending = RX_MAX_PENDING; + ering->rx_mini_max_pending = 0; + ering->rx_jumbo_max_pending = 0; + ering->tx_max_pending = TX_MAX_PENDING; + + ering->rx_pending = sky2->rx_pending; + ering->rx_mini_pending = 0; + ering->rx_jumbo_pending = 0; + ering->tx_pending = sky2->tx_pending; +} + +static int sky2_set_ringparam(struct net_device *dev, + struct ethtool_ringparam *ering) +{ + struct sky2_port *sky2 = netdev_priv(dev); + + if (ering->rx_pending > RX_MAX_PENDING || + ering->rx_pending < 8 || + ering->tx_pending < TX_MIN_PENDING || + ering->tx_pending > TX_MAX_PENDING) + return -EINVAL; + + sky2_detach(dev); + + sky2->rx_pending = ering->rx_pending; + sky2->tx_pending = ering->tx_pending; + sky2->tx_ring_size = roundup_pow_of_two(sky2->tx_pending+1); + + return sky2_reattach(dev); +} + +static int sky2_get_regs_len(struct net_device *dev) +{ + return 0x4000; +} + +static int sky2_reg_access_ok(struct sky2_hw *hw, unsigned int b) +{ + /* This complicated switch statement is to make sure and + * only access regions that are unreserved. + * Some blocks are only valid on dual port cards. + */ + switch (b) { + /* second port */ + case 5: /* Tx Arbiter 2 */ + case 9: /* RX2 */ + case 14 ... 15: /* TX2 */ + case 17: case 19: /* Ram Buffer 2 */ + case 22 ... 23: /* Tx Ram Buffer 2 */ + case 25: /* Rx MAC Fifo 1 */ + case 27: /* Tx MAC Fifo 2 */ + case 31: /* GPHY 2 */ + case 40 ... 47: /* Pattern Ram 2 */ + case 52: case 54: /* TCP Segmentation 2 */ + case 112 ... 116: /* GMAC 2 */ + return hw->ports > 1; + + case 0: /* Control */ + case 2: /* Mac address */ + case 4: /* Tx Arbiter 1 */ + case 7: /* PCI express reg */ + case 8: /* RX1 */ + case 12 ... 13: /* TX1 */ + case 16: case 18:/* Rx Ram Buffer 1 */ + case 20 ... 21: /* Tx Ram Buffer 1 */ + case 24: /* Rx MAC Fifo 1 */ + case 26: /* Tx MAC Fifo 1 */ + case 28 ... 29: /* Descriptor and status unit */ + case 30: /* GPHY 1*/ + case 32 ... 39: /* Pattern Ram 1 */ + case 48: case 50: /* TCP Segmentation 1 */ + case 56 ... 60: /* PCI space */ + case 80 ... 84: /* GMAC 1 */ + return 1; + + default: + return 0; + } +} + +/* + * Returns copy of control register region + * Note: ethtool_get_regs always provides full size (16k) buffer + */ +static void sky2_get_regs(struct net_device *dev, struct ethtool_regs *regs, + void *p) +{ + const struct sky2_port *sky2 = netdev_priv(dev); + const void __iomem *io = sky2->hw->regs; + unsigned int b; + + regs->version = 1; + + for (b = 0; b < 128; b++) { + /* skip poisonous diagnostic ram region in block 3 */ + if (b == 3) + memcpy_fromio(p + 0x10, io + 0x10, 128 - 0x10); + else if (sky2_reg_access_ok(sky2->hw, b)) + memcpy_fromio(p, io, 128); + else + memset(p, 0, 128); + + p += 128; + io += 128; + } +} + +static int sky2_get_eeprom_len(struct net_device *dev) +{ + struct sky2_port *sky2 = netdev_priv(dev); + struct sky2_hw *hw = sky2->hw; + u16 reg2; + + reg2 = sky2_pci_read16(hw, PCI_DEV_REG2); + return 1 << ( ((reg2 & PCI_VPD_ROM_SZ) >> 14) + 8); +} + +static int sky2_vpd_wait(const struct sky2_hw *hw, int cap, u16 busy) +{ + unsigned long start = jiffies; + + while ( (sky2_pci_read16(hw, cap + PCI_VPD_ADDR) & PCI_VPD_ADDR_F) == busy) { + /* Can take up to 10.6 ms for write */ + if (time_after(jiffies, start + HZ/4)) { + dev_err(&hw->pdev->dev, "VPD cycle timed out\n"); + return -ETIMEDOUT; + } + mdelay(1); + } + + return 0; +} + +static int sky2_vpd_read(struct sky2_hw *hw, int cap, void *data, + u16 offset, size_t length) +{ + int rc = 0; + + while (length > 0) { + u32 val; + + sky2_pci_write16(hw, cap + PCI_VPD_ADDR, offset); + rc = sky2_vpd_wait(hw, cap, 0); + if (rc) + break; + + val = sky2_pci_read32(hw, cap + PCI_VPD_DATA); + + memcpy(data, &val, min(sizeof(val), length)); + offset += sizeof(u32); + data += sizeof(u32); + length -= sizeof(u32); + } + + return rc; +} + +static int sky2_vpd_write(struct sky2_hw *hw, int cap, const void *data, + u16 offset, unsigned int length) +{ + unsigned int i; + int rc = 0; + + for (i = 0; i < length; i += sizeof(u32)) { + u32 val = *(u32 *)(data + i); + + sky2_pci_write32(hw, cap + PCI_VPD_DATA, val); + sky2_pci_write32(hw, cap + PCI_VPD_ADDR, offset | PCI_VPD_ADDR_F); + + rc = sky2_vpd_wait(hw, cap, PCI_VPD_ADDR_F); + if (rc) + break; + } + return rc; +} + +static int sky2_get_eeprom(struct net_device *dev, struct ethtool_eeprom *eeprom, + u8 *data) +{ + struct sky2_port *sky2 = netdev_priv(dev); + int cap = pci_find_capability(sky2->hw->pdev, PCI_CAP_ID_VPD); + + if (!cap) + return -EINVAL; + + eeprom->magic = SKY2_EEPROM_MAGIC; + + return sky2_vpd_read(sky2->hw, cap, data, eeprom->offset, eeprom->len); +} + +static int sky2_set_eeprom(struct net_device *dev, struct ethtool_eeprom *eeprom, + u8 *data) +{ + struct sky2_port *sky2 = netdev_priv(dev); + int cap = pci_find_capability(sky2->hw->pdev, PCI_CAP_ID_VPD); + + if (!cap) + return -EINVAL; + + if (eeprom->magic != SKY2_EEPROM_MAGIC) + return -EINVAL; + + /* Partial writes not supported */ + if ((eeprom->offset & 3) || (eeprom->len & 3)) + return -EINVAL; + + return sky2_vpd_write(sky2->hw, cap, data, eeprom->offset, eeprom->len); +} + +static u32 sky2_fix_features(struct net_device *dev, u32 features) +{ + const struct sky2_port *sky2 = netdev_priv(dev); + const struct sky2_hw *hw = sky2->hw; + + /* In order to do Jumbo packets on these chips, need to turn off the + * transmit store/forward. Therefore checksum offload won't work. + */ + if (dev->mtu > ETH_DATA_LEN && hw->chip_id == CHIP_ID_YUKON_EC_U) { + netdev_info(dev, "checksum offload not possible with jumbo frames\n"); + features &= ~(NETIF_F_TSO|NETIF_F_SG|NETIF_F_ALL_CSUM); + } + + /* Some hardware requires receive checksum for RSS to work. */ + if ( (features & NETIF_F_RXHASH) && + !(features & NETIF_F_RXCSUM) && + (sky2->hw->flags & SKY2_HW_RSS_CHKSUM)) { + netdev_info(dev, "receive hashing forces receive checksum\n"); + features |= NETIF_F_RXCSUM; + } + + return features; +} + +static int sky2_set_features(struct net_device *dev, u32 features) +{ + struct sky2_port *sky2 = netdev_priv(dev); + u32 changed = dev->features ^ features; + + if (changed & NETIF_F_RXCSUM) { + u32 on = features & NETIF_F_RXCSUM; + sky2_write32(sky2->hw, Q_ADDR(rxqaddr[sky2->port], Q_CSR), + on ? BMU_ENA_RX_CHKSUM : BMU_DIS_RX_CHKSUM); + } + + if (changed & NETIF_F_RXHASH) + rx_set_rss(dev, features); + + if (changed & (NETIF_F_HW_VLAN_TX|NETIF_F_HW_VLAN_RX)) + sky2_vlan_mode(dev, features); + + return 0; +} + +static const struct ethtool_ops sky2_ethtool_ops = { + .get_settings = sky2_get_settings, + .set_settings = sky2_set_settings, + .get_drvinfo = sky2_get_drvinfo, + .get_wol = sky2_get_wol, + .set_wol = sky2_set_wol, + .get_msglevel = sky2_get_msglevel, + .set_msglevel = sky2_set_msglevel, + .nway_reset = sky2_nway_reset, + .get_regs_len = sky2_get_regs_len, + .get_regs = sky2_get_regs, + .get_link = ethtool_op_get_link, + .get_eeprom_len = sky2_get_eeprom_len, + .get_eeprom = sky2_get_eeprom, + .set_eeprom = sky2_set_eeprom, + .get_strings = sky2_get_strings, + .get_coalesce = sky2_get_coalesce, + .set_coalesce = sky2_set_coalesce, + .get_ringparam = sky2_get_ringparam, + .set_ringparam = sky2_set_ringparam, + .get_pauseparam = sky2_get_pauseparam, + .set_pauseparam = sky2_set_pauseparam, + .set_phys_id = sky2_set_phys_id, + .get_sset_count = sky2_get_sset_count, + .get_ethtool_stats = sky2_get_ethtool_stats, +}; + +#ifdef CONFIG_SKY2_DEBUG + +static struct dentry *sky2_debug; + + +/* + * Read and parse the first part of Vital Product Data + */ +#define VPD_SIZE 128 +#define VPD_MAGIC 0x82 + +static const struct vpd_tag { + char tag[2]; + char *label; +} vpd_tags[] = { + { "PN", "Part Number" }, + { "EC", "Engineering Level" }, + { "MN", "Manufacturer" }, + { "SN", "Serial Number" }, + { "YA", "Asset Tag" }, + { "VL", "First Error Log Message" }, + { "VF", "Second Error Log Message" }, + { "VB", "Boot Agent ROM Configuration" }, + { "VE", "EFI UNDI Configuration" }, +}; + +static void sky2_show_vpd(struct seq_file *seq, struct sky2_hw *hw) +{ + size_t vpd_size; + loff_t offs; + u8 len; + unsigned char *buf; + u16 reg2; + + reg2 = sky2_pci_read16(hw, PCI_DEV_REG2); + vpd_size = 1 << ( ((reg2 & PCI_VPD_ROM_SZ) >> 14) + 8); + + seq_printf(seq, "%s Product Data\n", pci_name(hw->pdev)); + buf = kmalloc(vpd_size, GFP_KERNEL); + if (!buf) { + seq_puts(seq, "no memory!\n"); + return; + } + + if (pci_read_vpd(hw->pdev, 0, vpd_size, buf) < 0) { + seq_puts(seq, "VPD read failed\n"); + goto out; + } + + if (buf[0] != VPD_MAGIC) { + seq_printf(seq, "VPD tag mismatch: %#x\n", buf[0]); + goto out; + } + len = buf[1]; + if (len == 0 || len > vpd_size - 4) { + seq_printf(seq, "Invalid id length: %d\n", len); + goto out; + } + + seq_printf(seq, "%.*s\n", len, buf + 3); + offs = len + 3; + + while (offs < vpd_size - 4) { + int i; + + if (!memcmp("RW", buf + offs, 2)) /* end marker */ + break; + len = buf[offs + 2]; + if (offs + len + 3 >= vpd_size) + break; + + for (i = 0; i < ARRAY_SIZE(vpd_tags); i++) { + if (!memcmp(vpd_tags[i].tag, buf + offs, 2)) { + seq_printf(seq, " %s: %.*s\n", + vpd_tags[i].label, len, buf + offs + 3); + break; + } + } + offs += len + 3; + } +out: + kfree(buf); +} + +static int sky2_debug_show(struct seq_file *seq, void *v) +{ + struct net_device *dev = seq->private; + const struct sky2_port *sky2 = netdev_priv(dev); + struct sky2_hw *hw = sky2->hw; + unsigned port = sky2->port; + unsigned idx, last; + int sop; + + sky2_show_vpd(seq, hw); + + seq_printf(seq, "\nIRQ src=%x mask=%x control=%x\n", + sky2_read32(hw, B0_ISRC), + sky2_read32(hw, B0_IMSK), + sky2_read32(hw, B0_Y2_SP_ICR)); + + if (!netif_running(dev)) { + seq_printf(seq, "network not running\n"); + return 0; + } + + napi_disable(&hw->napi); + last = sky2_read16(hw, STAT_PUT_IDX); + + seq_printf(seq, "Status ring %u\n", hw->st_size); + if (hw->st_idx == last) + seq_puts(seq, "Status ring (empty)\n"); + else { + seq_puts(seq, "Status ring\n"); + for (idx = hw->st_idx; idx != last && idx < hw->st_size; + idx = RING_NEXT(idx, hw->st_size)) { + const struct sky2_status_le *le = hw->st_le + idx; + seq_printf(seq, "[%d] %#x %d %#x\n", + idx, le->opcode, le->length, le->status); + } + seq_puts(seq, "\n"); + } + + seq_printf(seq, "Tx ring pending=%u...%u report=%d done=%d\n", + sky2->tx_cons, sky2->tx_prod, + sky2_read16(hw, port == 0 ? STAT_TXA1_RIDX : STAT_TXA2_RIDX), + sky2_read16(hw, Q_ADDR(txqaddr[port], Q_DONE))); + + /* Dump contents of tx ring */ + sop = 1; + for (idx = sky2->tx_next; idx != sky2->tx_prod && idx < sky2->tx_ring_size; + idx = RING_NEXT(idx, sky2->tx_ring_size)) { + const struct sky2_tx_le *le = sky2->tx_le + idx; + u32 a = le32_to_cpu(le->addr); + + if (sop) + seq_printf(seq, "%u:", idx); + sop = 0; + + switch (le->opcode & ~HW_OWNER) { + case OP_ADDR64: + seq_printf(seq, " %#x:", a); + break; + case OP_LRGLEN: + seq_printf(seq, " mtu=%d", a); + break; + case OP_VLAN: + seq_printf(seq, " vlan=%d", be16_to_cpu(le->length)); + break; + case OP_TCPLISW: + seq_printf(seq, " csum=%#x", a); + break; + case OP_LARGESEND: + seq_printf(seq, " tso=%#x(%d)", a, le16_to_cpu(le->length)); + break; + case OP_PACKET: + seq_printf(seq, " %#x(%d)", a, le16_to_cpu(le->length)); + break; + case OP_BUFFER: + seq_printf(seq, " frag=%#x(%d)", a, le16_to_cpu(le->length)); + break; + default: + seq_printf(seq, " op=%#x,%#x(%d)", le->opcode, + a, le16_to_cpu(le->length)); + } + + if (le->ctrl & EOP) { + seq_putc(seq, '\n'); + sop = 1; + } + } + + seq_printf(seq, "\nRx ring hw get=%d put=%d last=%d\n", + sky2_read16(hw, Y2_QADDR(rxqaddr[port], PREF_UNIT_GET_IDX)), + sky2_read16(hw, Y2_QADDR(rxqaddr[port], PREF_UNIT_PUT_IDX)), + sky2_read16(hw, Y2_QADDR(rxqaddr[port], PREF_UNIT_LAST_IDX))); + + sky2_read32(hw, B0_Y2_SP_LISR); + napi_enable(&hw->napi); + return 0; +} + +static int sky2_debug_open(struct inode *inode, struct file *file) +{ + return single_open(file, sky2_debug_show, inode->i_private); +} + +static const struct file_operations sky2_debug_fops = { + .owner = THIS_MODULE, + .open = sky2_debug_open, + .read = seq_read, + .llseek = seq_lseek, + .release = single_release, +}; + +/* + * Use network device events to create/remove/rename + * debugfs file entries + */ +static int sky2_device_event(struct notifier_block *unused, + unsigned long event, void *ptr) +{ + struct net_device *dev = ptr; + struct sky2_port *sky2 = netdev_priv(dev); + + if (dev->netdev_ops->ndo_open != sky2_up || !sky2_debug) + return NOTIFY_DONE; + + switch (event) { + case NETDEV_CHANGENAME: + if (sky2->debugfs) { + sky2->debugfs = debugfs_rename(sky2_debug, sky2->debugfs, + sky2_debug, dev->name); + } + break; + + case NETDEV_GOING_DOWN: + if (sky2->debugfs) { + netdev_printk(KERN_DEBUG, dev, "remove debugfs\n"); + debugfs_remove(sky2->debugfs); + sky2->debugfs = NULL; + } + break; + + case NETDEV_UP: + sky2->debugfs = debugfs_create_file(dev->name, S_IRUGO, + sky2_debug, dev, + &sky2_debug_fops); + if (IS_ERR(sky2->debugfs)) + sky2->debugfs = NULL; + } + + return NOTIFY_DONE; +} + +static struct notifier_block sky2_notifier = { + .notifier_call = sky2_device_event, +}; + + +static __init void sky2_debug_init(void) +{ + struct dentry *ent; + + ent = debugfs_create_dir("sky2", NULL); + if (!ent || IS_ERR(ent)) + return; + + sky2_debug = ent; + register_netdevice_notifier(&sky2_notifier); +} + +static __exit void sky2_debug_cleanup(void) +{ + if (sky2_debug) { + unregister_netdevice_notifier(&sky2_notifier); + debugfs_remove(sky2_debug); + sky2_debug = NULL; + } +} + +#else +#define sky2_debug_init() +#define sky2_debug_cleanup() +#endif + +/* Two copies of network device operations to handle special case of + not allowing netpoll on second port */ +static const struct net_device_ops sky2_netdev_ops[2] = { + { + .ndo_open = sky2_up, + .ndo_stop = sky2_down, + .ndo_start_xmit = sky2_xmit_frame, + .ndo_do_ioctl = sky2_ioctl, + .ndo_validate_addr = eth_validate_addr, + .ndo_set_mac_address = sky2_set_mac_address, + .ndo_set_multicast_list = sky2_set_multicast, + .ndo_change_mtu = sky2_change_mtu, + .ndo_fix_features = sky2_fix_features, + .ndo_set_features = sky2_set_features, + .ndo_tx_timeout = sky2_tx_timeout, + .ndo_get_stats64 = sky2_get_stats, +#ifdef CONFIG_NET_POLL_CONTROLLER + .ndo_poll_controller = sky2_netpoll, +#endif + }, + { + .ndo_open = sky2_up, + .ndo_stop = sky2_down, + .ndo_start_xmit = sky2_xmit_frame, + .ndo_do_ioctl = sky2_ioctl, + .ndo_validate_addr = eth_validate_addr, + .ndo_set_mac_address = sky2_set_mac_address, + .ndo_set_multicast_list = sky2_set_multicast, + .ndo_change_mtu = sky2_change_mtu, + .ndo_fix_features = sky2_fix_features, + .ndo_set_features = sky2_set_features, + .ndo_tx_timeout = sky2_tx_timeout, + .ndo_get_stats64 = sky2_get_stats, + }, +}; + +/* Initialize network device */ +static __devinit struct net_device *sky2_init_netdev(struct sky2_hw *hw, + unsigned port, + int highmem, int wol) +{ + struct sky2_port *sky2; + struct net_device *dev = alloc_etherdev(sizeof(*sky2)); + + if (!dev) { + dev_err(&hw->pdev->dev, "etherdev alloc failed\n"); + return NULL; + } + + SET_NETDEV_DEV(dev, &hw->pdev->dev); + dev->irq = hw->pdev->irq; + SET_ETHTOOL_OPS(dev, &sky2_ethtool_ops); + dev->watchdog_timeo = TX_WATCHDOG; + dev->netdev_ops = &sky2_netdev_ops[port]; + + sky2 = netdev_priv(dev); + sky2->netdev = dev; + sky2->hw = hw; + sky2->msg_enable = netif_msg_init(debug, default_msg); + + /* Auto speed and flow control */ + sky2->flags = SKY2_FLAG_AUTO_SPEED | SKY2_FLAG_AUTO_PAUSE; + if (hw->chip_id != CHIP_ID_YUKON_XL) + dev->hw_features |= NETIF_F_RXCSUM; + + sky2->flow_mode = FC_BOTH; + + sky2->duplex = -1; + sky2->speed = -1; + sky2->advertising = sky2_supported_modes(hw); + sky2->wol = wol; + + spin_lock_init(&sky2->phy_lock); + + sky2->tx_pending = TX_DEF_PENDING; + sky2->tx_ring_size = roundup_pow_of_two(TX_DEF_PENDING+1); + sky2->rx_pending = RX_DEF_PENDING; + + hw->dev[port] = dev; + + sky2->port = port; + + dev->hw_features |= NETIF_F_IP_CSUM | NETIF_F_SG | NETIF_F_TSO; + + if (highmem) + dev->features |= NETIF_F_HIGHDMA; + + /* Enable receive hashing unless hardware is known broken */ + if (!(hw->flags & SKY2_HW_RSS_BROKEN)) + dev->hw_features |= NETIF_F_RXHASH; + + if (!(hw->flags & SKY2_HW_VLAN_BROKEN)) { + dev->hw_features |= NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX; + dev->vlan_features |= SKY2_VLAN_OFFLOADS; + } + + dev->features |= dev->hw_features; + + /* read the mac address */ + memcpy_fromio(dev->dev_addr, hw->regs + B2_MAC_1 + port * 8, ETH_ALEN); + memcpy(dev->perm_addr, dev->dev_addr, dev->addr_len); + + return dev; +} + +static void __devinit sky2_show_addr(struct net_device *dev) +{ + const struct sky2_port *sky2 = netdev_priv(dev); + + netif_info(sky2, probe, dev, "addr %pM\n", dev->dev_addr); +} + +/* Handle software interrupt used during MSI test */ +static irqreturn_t __devinit sky2_test_intr(int irq, void *dev_id) +{ + struct sky2_hw *hw = dev_id; + u32 status = sky2_read32(hw, B0_Y2_SP_ISRC2); + + if (status == 0) + return IRQ_NONE; + + if (status & Y2_IS_IRQ_SW) { + hw->flags |= SKY2_HW_USE_MSI; + wake_up(&hw->msi_wait); + sky2_write8(hw, B0_CTST, CS_CL_SW_IRQ); + } + sky2_write32(hw, B0_Y2_SP_ICR, 2); + + return IRQ_HANDLED; +} + +/* Test interrupt path by forcing a a software IRQ */ +static int __devinit sky2_test_msi(struct sky2_hw *hw) +{ + struct pci_dev *pdev = hw->pdev; + int err; + + init_waitqueue_head(&hw->msi_wait); + + sky2_write32(hw, B0_IMSK, Y2_IS_IRQ_SW); + + err = request_irq(pdev->irq, sky2_test_intr, 0, DRV_NAME, hw); + if (err) { + dev_err(&pdev->dev, "cannot assign irq %d\n", pdev->irq); + return err; + } + + sky2_write8(hw, B0_CTST, CS_ST_SW_IRQ); + sky2_read8(hw, B0_CTST); + + wait_event_timeout(hw->msi_wait, (hw->flags & SKY2_HW_USE_MSI), HZ/10); + + if (!(hw->flags & SKY2_HW_USE_MSI)) { + /* MSI test failed, go back to INTx mode */ + dev_info(&pdev->dev, "No interrupt generated using MSI, " + "switching to INTx mode.\n"); + + err = -EOPNOTSUPP; + sky2_write8(hw, B0_CTST, CS_CL_SW_IRQ); + } + + sky2_write32(hw, B0_IMSK, 0); + sky2_read32(hw, B0_IMSK); + + free_irq(pdev->irq, hw); + + return err; +} + +/* This driver supports yukon2 chipset only */ +static const char *sky2_name(u8 chipid, char *buf, int sz) +{ + const char *name[] = { + "XL", /* 0xb3 */ + "EC Ultra", /* 0xb4 */ + "Extreme", /* 0xb5 */ + "EC", /* 0xb6 */ + "FE", /* 0xb7 */ + "FE+", /* 0xb8 */ + "Supreme", /* 0xb9 */ + "UL 2", /* 0xba */ + "Unknown", /* 0xbb */ + "Optima", /* 0xbc */ + "Optima Prime", /* 0xbd */ + "Optima 2", /* 0xbe */ + }; + + if (chipid >= CHIP_ID_YUKON_XL && chipid <= CHIP_ID_YUKON_OP_2) + strncpy(buf, name[chipid - CHIP_ID_YUKON_XL], sz); + else + snprintf(buf, sz, "(chip %#x)", chipid); + return buf; +} + +static int __devinit sky2_probe(struct pci_dev *pdev, + const struct pci_device_id *ent) +{ + struct net_device *dev; + struct sky2_hw *hw; + int err, using_dac = 0, wol_default; + u32 reg; + char buf1[16]; + + err = pci_enable_device(pdev); + if (err) { + dev_err(&pdev->dev, "cannot enable PCI device\n"); + goto err_out; + } + + /* Get configuration information + * Note: only regular PCI config access once to test for HW issues + * other PCI access through shared memory for speed and to + * avoid MMCONFIG problems. + */ + err = pci_read_config_dword(pdev, PCI_DEV_REG2, ®); + if (err) { + dev_err(&pdev->dev, "PCI read config failed\n"); + goto err_out; + } + + if (~reg == 0) { + dev_err(&pdev->dev, "PCI configuration read error\n"); + goto err_out; + } + + err = pci_request_regions(pdev, DRV_NAME); + if (err) { + dev_err(&pdev->dev, "cannot obtain PCI resources\n"); + goto err_out_disable; + } + + pci_set_master(pdev); + + if (sizeof(dma_addr_t) > sizeof(u32) && + !(err = pci_set_dma_mask(pdev, DMA_BIT_MASK(64)))) { + using_dac = 1; + err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64)); + if (err < 0) { + dev_err(&pdev->dev, "unable to obtain 64 bit DMA " + "for consistent allocations\n"); + goto err_out_free_regions; + } + } else { + err = pci_set_dma_mask(pdev, DMA_BIT_MASK(32)); + if (err) { + dev_err(&pdev->dev, "no usable DMA configuration\n"); + goto err_out_free_regions; + } + } + + +#ifdef __BIG_ENDIAN + /* The sk98lin vendor driver uses hardware byte swapping but + * this driver uses software swapping. + */ + reg &= ~PCI_REV_DESC; + err = pci_write_config_dword(pdev, PCI_DEV_REG2, reg); + if (err) { + dev_err(&pdev->dev, "PCI write config failed\n"); + goto err_out_free_regions; + } +#endif + + wol_default = device_may_wakeup(&pdev->dev) ? WAKE_MAGIC : 0; + + err = -ENOMEM; + + hw = kzalloc(sizeof(*hw) + strlen(DRV_NAME "@pci:") + + strlen(pci_name(pdev)) + 1, GFP_KERNEL); + if (!hw) { + dev_err(&pdev->dev, "cannot allocate hardware struct\n"); + goto err_out_free_regions; + } + + hw->pdev = pdev; + sprintf(hw->irq_name, DRV_NAME "@pci:%s", pci_name(pdev)); + + hw->regs = ioremap_nocache(pci_resource_start(pdev, 0), 0x4000); + if (!hw->regs) { + dev_err(&pdev->dev, "cannot map device registers\n"); + goto err_out_free_hw; + } + + err = sky2_init(hw); + if (err) + goto err_out_iounmap; + + /* ring for status responses */ + hw->st_size = hw->ports * roundup_pow_of_two(3*RX_MAX_PENDING + TX_MAX_PENDING); + hw->st_le = pci_alloc_consistent(pdev, hw->st_size * sizeof(struct sky2_status_le), + &hw->st_dma); + if (!hw->st_le) + goto err_out_reset; + + dev_info(&pdev->dev, "Yukon-2 %s chip revision %d\n", + sky2_name(hw->chip_id, buf1, sizeof(buf1)), hw->chip_rev); + + sky2_reset(hw); + + dev = sky2_init_netdev(hw, 0, using_dac, wol_default); + if (!dev) { + err = -ENOMEM; + goto err_out_free_pci; + } + + if (!disable_msi && pci_enable_msi(pdev) == 0) { + err = sky2_test_msi(hw); + if (err == -EOPNOTSUPP) + pci_disable_msi(pdev); + else if (err) + goto err_out_free_netdev; + } + + err = register_netdev(dev); + if (err) { + dev_err(&pdev->dev, "cannot register net device\n"); + goto err_out_free_netdev; + } + + netif_carrier_off(dev); + + netif_napi_add(dev, &hw->napi, sky2_poll, NAPI_WEIGHT); + + err = request_irq(pdev->irq, sky2_intr, + (hw->flags & SKY2_HW_USE_MSI) ? 0 : IRQF_SHARED, + hw->irq_name, hw); + if (err) { + dev_err(&pdev->dev, "cannot assign irq %d\n", pdev->irq); + goto err_out_unregister; + } + sky2_write32(hw, B0_IMSK, Y2_IS_BASE); + napi_enable(&hw->napi); + + sky2_show_addr(dev); + + if (hw->ports > 1) { + struct net_device *dev1; + + err = -ENOMEM; + dev1 = sky2_init_netdev(hw, 1, using_dac, wol_default); + if (dev1 && (err = register_netdev(dev1)) == 0) + sky2_show_addr(dev1); + else { + dev_warn(&pdev->dev, + "register of second port failed (%d)\n", err); + hw->dev[1] = NULL; + hw->ports = 1; + if (dev1) + free_netdev(dev1); + } + } + + setup_timer(&hw->watchdog_timer, sky2_watchdog, (unsigned long) hw); + INIT_WORK(&hw->restart_work, sky2_restart); + + pci_set_drvdata(pdev, hw); + pdev->d3_delay = 150; + + return 0; + +err_out_unregister: + if (hw->flags & SKY2_HW_USE_MSI) + pci_disable_msi(pdev); + unregister_netdev(dev); +err_out_free_netdev: + free_netdev(dev); +err_out_free_pci: + pci_free_consistent(pdev, hw->st_size * sizeof(struct sky2_status_le), + hw->st_le, hw->st_dma); +err_out_reset: + sky2_write8(hw, B0_CTST, CS_RST_SET); +err_out_iounmap: + iounmap(hw->regs); +err_out_free_hw: + kfree(hw); +err_out_free_regions: + pci_release_regions(pdev); +err_out_disable: + pci_disable_device(pdev); +err_out: + pci_set_drvdata(pdev, NULL); + return err; +} + +static void __devexit sky2_remove(struct pci_dev *pdev) +{ + struct sky2_hw *hw = pci_get_drvdata(pdev); + int i; + + if (!hw) + return; + + del_timer_sync(&hw->watchdog_timer); + cancel_work_sync(&hw->restart_work); + + for (i = hw->ports-1; i >= 0; --i) + unregister_netdev(hw->dev[i]); + + sky2_write32(hw, B0_IMSK, 0); + + sky2_power_aux(hw); + + sky2_write8(hw, B0_CTST, CS_RST_SET); + sky2_read8(hw, B0_CTST); + + free_irq(pdev->irq, hw); + if (hw->flags & SKY2_HW_USE_MSI) + pci_disable_msi(pdev); + pci_free_consistent(pdev, hw->st_size * sizeof(struct sky2_status_le), + hw->st_le, hw->st_dma); + pci_release_regions(pdev); + pci_disable_device(pdev); + + for (i = hw->ports-1; i >= 0; --i) + free_netdev(hw->dev[i]); + + iounmap(hw->regs); + kfree(hw); + + pci_set_drvdata(pdev, NULL); +} + +static int sky2_suspend(struct device *dev) +{ + struct pci_dev *pdev = to_pci_dev(dev); + struct sky2_hw *hw = pci_get_drvdata(pdev); + int i; + + if (!hw) + return 0; + + del_timer_sync(&hw->watchdog_timer); + cancel_work_sync(&hw->restart_work); + + rtnl_lock(); + + sky2_all_down(hw); + for (i = 0; i < hw->ports; i++) { + struct net_device *dev = hw->dev[i]; + struct sky2_port *sky2 = netdev_priv(dev); + + if (sky2->wol) + sky2_wol_init(sky2); + } + + sky2_power_aux(hw); + rtnl_unlock(); + + return 0; +} + +#ifdef CONFIG_PM_SLEEP +static int sky2_resume(struct device *dev) +{ + struct pci_dev *pdev = to_pci_dev(dev); + struct sky2_hw *hw = pci_get_drvdata(pdev); + int err; + + if (!hw) + return 0; + + /* Re-enable all clocks */ + err = pci_write_config_dword(pdev, PCI_DEV_REG3, 0); + if (err) { + dev_err(&pdev->dev, "PCI write config failed\n"); + goto out; + } + + rtnl_lock(); + sky2_reset(hw); + sky2_all_up(hw); + rtnl_unlock(); + + return 0; +out: + + dev_err(&pdev->dev, "resume failed (%d)\n", err); + pci_disable_device(pdev); + return err; +} + +static SIMPLE_DEV_PM_OPS(sky2_pm_ops, sky2_suspend, sky2_resume); +#define SKY2_PM_OPS (&sky2_pm_ops) + +#else + +#define SKY2_PM_OPS NULL +#endif + +static void sky2_shutdown(struct pci_dev *pdev) +{ + sky2_suspend(&pdev->dev); + pci_wake_from_d3(pdev, device_may_wakeup(&pdev->dev)); + pci_set_power_state(pdev, PCI_D3hot); +} + +static struct pci_driver sky2_driver = { + .name = DRV_NAME, + .id_table = sky2_id_table, + .probe = sky2_probe, + .remove = __devexit_p(sky2_remove), + .shutdown = sky2_shutdown, + .driver.pm = SKY2_PM_OPS, +}; + +static int __init sky2_init_module(void) +{ + pr_info("driver version " DRV_VERSION "\n"); + + sky2_debug_init(); + return pci_register_driver(&sky2_driver); +} + +static void __exit sky2_cleanup_module(void) +{ + pci_unregister_driver(&sky2_driver); + sky2_debug_cleanup(); +} + +module_init(sky2_init_module); +module_exit(sky2_cleanup_module); + +MODULE_DESCRIPTION("Marvell Yukon 2 Gigabit Ethernet driver"); +MODULE_AUTHOR("Stephen Hemminger <shemminger@linux-foundation.org>"); +MODULE_LICENSE("GPL"); +MODULE_VERSION(DRV_VERSION); |