summaryrefslogtreecommitdiffstats
path: root/drivers/net/ethernet/silan/sc92031.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/ethernet/silan/sc92031.c')
-rw-r--r--drivers/net/ethernet/silan/sc92031.c1609
1 files changed, 1609 insertions, 0 deletions
diff --git a/drivers/net/ethernet/silan/sc92031.c b/drivers/net/ethernet/silan/sc92031.c
new file mode 100644
index 00000000000..a284d644053
--- /dev/null
+++ b/drivers/net/ethernet/silan/sc92031.c
@@ -0,0 +1,1609 @@
+/* Silan SC92031 PCI Fast Ethernet Adapter driver
+ *
+ * Based on vendor drivers:
+ * Silan Fast Ethernet Netcard Driver:
+ * MODULE_AUTHOR ("gaoyonghong");
+ * MODULE_DESCRIPTION ("SILAN Fast Ethernet driver");
+ * MODULE_LICENSE("GPL");
+ * 8139D Fast Ethernet driver:
+ * (C) 2002 by gaoyonghong
+ * MODULE_AUTHOR ("gaoyonghong");
+ * MODULE_DESCRIPTION ("Rsltek 8139D PCI Fast Ethernet Adapter driver");
+ * MODULE_LICENSE("GPL");
+ * Both are almost identical and seem to be based on pci-skeleton.c
+ *
+ * Rewritten for 2.6 by Cesar Eduardo Barros
+ *
+ * A datasheet for this chip can be found at
+ * http://www.silan.com.cn/english/product/pdf/SC92031AY.pdf
+ */
+
+/* Note about set_mac_address: I don't know how to change the hardware
+ * matching, so you need to enable IFF_PROMISC when using it.
+ */
+
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/pci.h>
+#include <linux/dma-mapping.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/ethtool.h>
+#include <linux/mii.h>
+#include <linux/crc32.h>
+
+#include <asm/irq.h>
+
+#define SC92031_NAME "sc92031"
+
+/* BAR 0 is MMIO, BAR 1 is PIO */
+#ifndef SC92031_USE_BAR
+#define SC92031_USE_BAR 0
+#endif
+
+/* Maximum number of multicast addresses to filter (vs. Rx-all-multicast). */
+static int multicast_filter_limit = 64;
+module_param(multicast_filter_limit, int, 0);
+MODULE_PARM_DESC(multicast_filter_limit,
+ "Maximum number of filtered multicast addresses");
+
+static int media;
+module_param(media, int, 0);
+MODULE_PARM_DESC(media, "Media type (0x00 = autodetect,"
+ " 0x01 = 10M half, 0x02 = 10M full,"
+ " 0x04 = 100M half, 0x08 = 100M full)");
+
+/* Size of the in-memory receive ring. */
+#define RX_BUF_LEN_IDX 3 /* 0==8K, 1==16K, 2==32K, 3==64K ,4==128K*/
+#define RX_BUF_LEN (8192 << RX_BUF_LEN_IDX)
+
+/* Number of Tx descriptor registers. */
+#define NUM_TX_DESC 4
+
+/* max supported ethernet frame size -- must be at least (dev->mtu+14+4).*/
+#define MAX_ETH_FRAME_SIZE 1536
+
+/* Size of the Tx bounce buffers -- must be at least (dev->mtu+14+4). */
+#define TX_BUF_SIZE MAX_ETH_FRAME_SIZE
+#define TX_BUF_TOT_LEN (TX_BUF_SIZE * NUM_TX_DESC)
+
+/* The following settings are log_2(bytes)-4: 0 == 16 bytes .. 6==1024, 7==end of packet. */
+#define RX_FIFO_THRESH 7 /* Rx buffer level before first PCI xfer. */
+
+/* Time in jiffies before concluding the transmitter is hung. */
+#define TX_TIMEOUT (4*HZ)
+
+#define SILAN_STATS_NUM 2 /* number of ETHTOOL_GSTATS */
+
+/* media options */
+#define AUTOSELECT 0x00
+#define M10_HALF 0x01
+#define M10_FULL 0x02
+#define M100_HALF 0x04
+#define M100_FULL 0x08
+
+ /* Symbolic offsets to registers. */
+enum silan_registers {
+ Config0 = 0x00, // Config0
+ Config1 = 0x04, // Config1
+ RxBufWPtr = 0x08, // Rx buffer writer poiter
+ IntrStatus = 0x0C, // Interrupt status
+ IntrMask = 0x10, // Interrupt mask
+ RxbufAddr = 0x14, // Rx buffer start address
+ RxBufRPtr = 0x18, // Rx buffer read pointer
+ Txstatusall = 0x1C, // Transmit status of all descriptors
+ TxStatus0 = 0x20, // Transmit status (Four 32bit registers).
+ TxAddr0 = 0x30, // Tx descriptors (also four 32bit).
+ RxConfig = 0x40, // Rx configuration
+ MAC0 = 0x44, // Ethernet hardware address.
+ MAR0 = 0x4C, // Multicast filter.
+ RxStatus0 = 0x54, // Rx status
+ TxConfig = 0x5C, // Tx configuration
+ PhyCtrl = 0x60, // physical control
+ FlowCtrlConfig = 0x64, // flow control
+ Miicmd0 = 0x68, // Mii command0 register
+ Miicmd1 = 0x6C, // Mii command1 register
+ Miistatus = 0x70, // Mii status register
+ Timercnt = 0x74, // Timer counter register
+ TimerIntr = 0x78, // Timer interrupt register
+ PMConfig = 0x7C, // Power Manager configuration
+ CRC0 = 0x80, // Power Manager CRC ( Two 32bit regisers)
+ Wakeup0 = 0x88, // power Manager wakeup( Eight 64bit regiser)
+ LSBCRC0 = 0xC8, // power Manager LSBCRC(Two 32bit regiser)
+ TestD0 = 0xD0,
+ TestD4 = 0xD4,
+ TestD8 = 0xD8,
+};
+
+#define MII_JAB 16
+#define MII_OutputStatus 24
+
+#define PHY_16_JAB_ENB 0x1000
+#define PHY_16_PORT_ENB 0x1
+
+enum IntrStatusBits {
+ LinkFail = 0x80000000,
+ LinkOK = 0x40000000,
+ TimeOut = 0x20000000,
+ RxOverflow = 0x0040,
+ RxOK = 0x0020,
+ TxOK = 0x0001,
+ IntrBits = LinkFail|LinkOK|TimeOut|RxOverflow|RxOK|TxOK,
+};
+
+enum TxStatusBits {
+ TxCarrierLost = 0x20000000,
+ TxAborted = 0x10000000,
+ TxOutOfWindow = 0x08000000,
+ TxNccShift = 22,
+ EarlyTxThresShift = 16,
+ TxStatOK = 0x8000,
+ TxUnderrun = 0x4000,
+ TxOwn = 0x2000,
+};
+
+enum RxStatusBits {
+ RxStatesOK = 0x80000,
+ RxBadAlign = 0x40000,
+ RxHugeFrame = 0x20000,
+ RxSmallFrame = 0x10000,
+ RxCRCOK = 0x8000,
+ RxCrlFrame = 0x4000,
+ Rx_Broadcast = 0x2000,
+ Rx_Multicast = 0x1000,
+ RxAddrMatch = 0x0800,
+ MiiErr = 0x0400,
+};
+
+enum RxConfigBits {
+ RxFullDx = 0x80000000,
+ RxEnb = 0x40000000,
+ RxSmall = 0x20000000,
+ RxHuge = 0x10000000,
+ RxErr = 0x08000000,
+ RxAllphys = 0x04000000,
+ RxMulticast = 0x02000000,
+ RxBroadcast = 0x01000000,
+ RxLoopBack = (1 << 23) | (1 << 22),
+ LowThresholdShift = 12,
+ HighThresholdShift = 2,
+};
+
+enum TxConfigBits {
+ TxFullDx = 0x80000000,
+ TxEnb = 0x40000000,
+ TxEnbPad = 0x20000000,
+ TxEnbHuge = 0x10000000,
+ TxEnbFCS = 0x08000000,
+ TxNoBackOff = 0x04000000,
+ TxEnbPrem = 0x02000000,
+ TxCareLostCrs = 0x1000000,
+ TxExdCollNum = 0xf00000,
+ TxDataRate = 0x80000,
+};
+
+enum PhyCtrlconfigbits {
+ PhyCtrlAne = 0x80000000,
+ PhyCtrlSpd100 = 0x40000000,
+ PhyCtrlSpd10 = 0x20000000,
+ PhyCtrlPhyBaseAddr = 0x1f000000,
+ PhyCtrlDux = 0x800000,
+ PhyCtrlReset = 0x400000,
+};
+
+enum FlowCtrlConfigBits {
+ FlowCtrlFullDX = 0x80000000,
+ FlowCtrlEnb = 0x40000000,
+};
+
+enum Config0Bits {
+ Cfg0_Reset = 0x80000000,
+ Cfg0_Anaoff = 0x40000000,
+ Cfg0_LDPS = 0x20000000,
+};
+
+enum Config1Bits {
+ Cfg1_EarlyRx = 1 << 31,
+ Cfg1_EarlyTx = 1 << 30,
+
+ //rx buffer size
+ Cfg1_Rcv8K = 0x0,
+ Cfg1_Rcv16K = 0x1,
+ Cfg1_Rcv32K = 0x3,
+ Cfg1_Rcv64K = 0x7,
+ Cfg1_Rcv128K = 0xf,
+};
+
+enum MiiCmd0Bits {
+ Mii_Divider = 0x20000000,
+ Mii_WRITE = 0x400000,
+ Mii_READ = 0x200000,
+ Mii_SCAN = 0x100000,
+ Mii_Tamod = 0x80000,
+ Mii_Drvmod = 0x40000,
+ Mii_mdc = 0x20000,
+ Mii_mdoen = 0x10000,
+ Mii_mdo = 0x8000,
+ Mii_mdi = 0x4000,
+};
+
+enum MiiStatusBits {
+ Mii_StatusBusy = 0x80000000,
+};
+
+enum PMConfigBits {
+ PM_Enable = 1 << 31,
+ PM_LongWF = 1 << 30,
+ PM_Magic = 1 << 29,
+ PM_LANWake = 1 << 28,
+ PM_LWPTN = (1 << 27 | 1<< 26),
+ PM_LinkUp = 1 << 25,
+ PM_WakeUp = 1 << 24,
+};
+
+/* Locking rules:
+ * priv->lock protects most of the fields of priv and most of the
+ * hardware registers. It does not have to protect against softirqs
+ * between sc92031_disable_interrupts and sc92031_enable_interrupts;
+ * it also does not need to be used in ->open and ->stop while the
+ * device interrupts are off.
+ * Not having to protect against softirqs is very useful due to heavy
+ * use of mdelay() at _sc92031_reset.
+ * Functions prefixed with _sc92031_ must be called with the lock held;
+ * functions prefixed with sc92031_ must be called without the lock held.
+ * Use mmiowb() before unlocking if the hardware was written to.
+ */
+
+/* Locking rules for the interrupt:
+ * - the interrupt and the tasklet never run at the same time
+ * - neither run between sc92031_disable_interrupts and
+ * sc92031_enable_interrupt
+ */
+
+struct sc92031_priv {
+ spinlock_t lock;
+ /* iomap.h cookie */
+ void __iomem *port_base;
+ /* pci device structure */
+ struct pci_dev *pdev;
+ /* tasklet */
+ struct tasklet_struct tasklet;
+
+ /* CPU address of rx ring */
+ void *rx_ring;
+ /* PCI address of rx ring */
+ dma_addr_t rx_ring_dma_addr;
+ /* PCI address of rx ring read pointer */
+ dma_addr_t rx_ring_tail;
+
+ /* tx ring write index */
+ unsigned tx_head;
+ /* tx ring read index */
+ unsigned tx_tail;
+ /* CPU address of tx bounce buffer */
+ void *tx_bufs;
+ /* PCI address of tx bounce buffer */
+ dma_addr_t tx_bufs_dma_addr;
+
+ /* copies of some hardware registers */
+ u32 intr_status;
+ atomic_t intr_mask;
+ u32 rx_config;
+ u32 tx_config;
+ u32 pm_config;
+
+ /* copy of some flags from dev->flags */
+ unsigned int mc_flags;
+
+ /* for ETHTOOL_GSTATS */
+ u64 tx_timeouts;
+ u64 rx_loss;
+
+ /* for dev->get_stats */
+ long rx_value;
+};
+
+/* I don't know which registers can be safely read; however, I can guess
+ * MAC0 is one of them. */
+static inline void _sc92031_dummy_read(void __iomem *port_base)
+{
+ ioread32(port_base + MAC0);
+}
+
+static u32 _sc92031_mii_wait(void __iomem *port_base)
+{
+ u32 mii_status;
+
+ do {
+ udelay(10);
+ mii_status = ioread32(port_base + Miistatus);
+ } while (mii_status & Mii_StatusBusy);
+
+ return mii_status;
+}
+
+static u32 _sc92031_mii_cmd(void __iomem *port_base, u32 cmd0, u32 cmd1)
+{
+ iowrite32(Mii_Divider, port_base + Miicmd0);
+
+ _sc92031_mii_wait(port_base);
+
+ iowrite32(cmd1, port_base + Miicmd1);
+ iowrite32(Mii_Divider | cmd0, port_base + Miicmd0);
+
+ return _sc92031_mii_wait(port_base);
+}
+
+static void _sc92031_mii_scan(void __iomem *port_base)
+{
+ _sc92031_mii_cmd(port_base, Mii_SCAN, 0x1 << 6);
+}
+
+static u16 _sc92031_mii_read(void __iomem *port_base, unsigned reg)
+{
+ return _sc92031_mii_cmd(port_base, Mii_READ, reg << 6) >> 13;
+}
+
+static void _sc92031_mii_write(void __iomem *port_base, unsigned reg, u16 val)
+{
+ _sc92031_mii_cmd(port_base, Mii_WRITE, (reg << 6) | ((u32)val << 11));
+}
+
+static void sc92031_disable_interrupts(struct net_device *dev)
+{
+ struct sc92031_priv *priv = netdev_priv(dev);
+ void __iomem *port_base = priv->port_base;
+
+ /* tell the tasklet/interrupt not to enable interrupts */
+ atomic_set(&priv->intr_mask, 0);
+ wmb();
+
+ /* stop interrupts */
+ iowrite32(0, port_base + IntrMask);
+ _sc92031_dummy_read(port_base);
+ mmiowb();
+
+ /* wait for any concurrent interrupt/tasklet to finish */
+ synchronize_irq(dev->irq);
+ tasklet_disable(&priv->tasklet);
+}
+
+static void sc92031_enable_interrupts(struct net_device *dev)
+{
+ struct sc92031_priv *priv = netdev_priv(dev);
+ void __iomem *port_base = priv->port_base;
+
+ tasklet_enable(&priv->tasklet);
+
+ atomic_set(&priv->intr_mask, IntrBits);
+ wmb();
+
+ iowrite32(IntrBits, port_base + IntrMask);
+ mmiowb();
+}
+
+static void _sc92031_disable_tx_rx(struct net_device *dev)
+{
+ struct sc92031_priv *priv = netdev_priv(dev);
+ void __iomem *port_base = priv->port_base;
+
+ priv->rx_config &= ~RxEnb;
+ priv->tx_config &= ~TxEnb;
+ iowrite32(priv->rx_config, port_base + RxConfig);
+ iowrite32(priv->tx_config, port_base + TxConfig);
+}
+
+static void _sc92031_enable_tx_rx(struct net_device *dev)
+{
+ struct sc92031_priv *priv = netdev_priv(dev);
+ void __iomem *port_base = priv->port_base;
+
+ priv->rx_config |= RxEnb;
+ priv->tx_config |= TxEnb;
+ iowrite32(priv->rx_config, port_base + RxConfig);
+ iowrite32(priv->tx_config, port_base + TxConfig);
+}
+
+static void _sc92031_tx_clear(struct net_device *dev)
+{
+ struct sc92031_priv *priv = netdev_priv(dev);
+
+ while (priv->tx_head - priv->tx_tail > 0) {
+ priv->tx_tail++;
+ dev->stats.tx_dropped++;
+ }
+ priv->tx_head = priv->tx_tail = 0;
+}
+
+static void _sc92031_set_mar(struct net_device *dev)
+{
+ struct sc92031_priv *priv = netdev_priv(dev);
+ void __iomem *port_base = priv->port_base;
+ u32 mar0 = 0, mar1 = 0;
+
+ if ((dev->flags & IFF_PROMISC) ||
+ netdev_mc_count(dev) > multicast_filter_limit ||
+ (dev->flags & IFF_ALLMULTI))
+ mar0 = mar1 = 0xffffffff;
+ else if (dev->flags & IFF_MULTICAST) {
+ struct netdev_hw_addr *ha;
+
+ netdev_for_each_mc_addr(ha, dev) {
+ u32 crc;
+ unsigned bit = 0;
+
+ crc = ~ether_crc(ETH_ALEN, ha->addr);
+ crc >>= 24;
+
+ if (crc & 0x01) bit |= 0x02;
+ if (crc & 0x02) bit |= 0x01;
+ if (crc & 0x10) bit |= 0x20;
+ if (crc & 0x20) bit |= 0x10;
+ if (crc & 0x40) bit |= 0x08;
+ if (crc & 0x80) bit |= 0x04;
+
+ if (bit > 31)
+ mar0 |= 0x1 << (bit - 32);
+ else
+ mar1 |= 0x1 << bit;
+ }
+ }
+
+ iowrite32(mar0, port_base + MAR0);
+ iowrite32(mar1, port_base + MAR0 + 4);
+}
+
+static void _sc92031_set_rx_config(struct net_device *dev)
+{
+ struct sc92031_priv *priv = netdev_priv(dev);
+ void __iomem *port_base = priv->port_base;
+ unsigned int old_mc_flags;
+ u32 rx_config_bits = 0;
+
+ old_mc_flags = priv->mc_flags;
+
+ if (dev->flags & IFF_PROMISC)
+ rx_config_bits |= RxSmall | RxHuge | RxErr | RxBroadcast
+ | RxMulticast | RxAllphys;
+
+ if (dev->flags & (IFF_ALLMULTI | IFF_MULTICAST))
+ rx_config_bits |= RxMulticast;
+
+ if (dev->flags & IFF_BROADCAST)
+ rx_config_bits |= RxBroadcast;
+
+ priv->rx_config &= ~(RxSmall | RxHuge | RxErr | RxBroadcast
+ | RxMulticast | RxAllphys);
+ priv->rx_config |= rx_config_bits;
+
+ priv->mc_flags = dev->flags & (IFF_PROMISC | IFF_ALLMULTI
+ | IFF_MULTICAST | IFF_BROADCAST);
+
+ if (netif_carrier_ok(dev) && priv->mc_flags != old_mc_flags)
+ iowrite32(priv->rx_config, port_base + RxConfig);
+}
+
+static bool _sc92031_check_media(struct net_device *dev)
+{
+ struct sc92031_priv *priv = netdev_priv(dev);
+ void __iomem *port_base = priv->port_base;
+ u16 bmsr;
+
+ bmsr = _sc92031_mii_read(port_base, MII_BMSR);
+ rmb();
+ if (bmsr & BMSR_LSTATUS) {
+ bool speed_100, duplex_full;
+ u32 flow_ctrl_config = 0;
+ u16 output_status = _sc92031_mii_read(port_base,
+ MII_OutputStatus);
+ _sc92031_mii_scan(port_base);
+
+ speed_100 = output_status & 0x2;
+ duplex_full = output_status & 0x4;
+
+ /* Initial Tx/Rx configuration */
+ priv->rx_config = (0x40 << LowThresholdShift) | (0x1c0 << HighThresholdShift);
+ priv->tx_config = 0x48800000;
+
+ /* NOTE: vendor driver had dead code here to enable tx padding */
+
+ if (!speed_100)
+ priv->tx_config |= 0x80000;
+
+ // configure rx mode
+ _sc92031_set_rx_config(dev);
+
+ if (duplex_full) {
+ priv->rx_config |= RxFullDx;
+ priv->tx_config |= TxFullDx;
+ flow_ctrl_config = FlowCtrlFullDX | FlowCtrlEnb;
+ } else {
+ priv->rx_config &= ~RxFullDx;
+ priv->tx_config &= ~TxFullDx;
+ }
+
+ _sc92031_set_mar(dev);
+ _sc92031_set_rx_config(dev);
+ _sc92031_enable_tx_rx(dev);
+ iowrite32(flow_ctrl_config, port_base + FlowCtrlConfig);
+
+ netif_carrier_on(dev);
+
+ if (printk_ratelimit())
+ printk(KERN_INFO "%s: link up, %sMbps, %s-duplex\n",
+ dev->name,
+ speed_100 ? "100" : "10",
+ duplex_full ? "full" : "half");
+ return true;
+ } else {
+ _sc92031_mii_scan(port_base);
+
+ netif_carrier_off(dev);
+
+ _sc92031_disable_tx_rx(dev);
+
+ if (printk_ratelimit())
+ printk(KERN_INFO "%s: link down\n", dev->name);
+ return false;
+ }
+}
+
+static void _sc92031_phy_reset(struct net_device *dev)
+{
+ struct sc92031_priv *priv = netdev_priv(dev);
+ void __iomem *port_base = priv->port_base;
+ u32 phy_ctrl;
+
+ phy_ctrl = ioread32(port_base + PhyCtrl);
+ phy_ctrl &= ~(PhyCtrlDux | PhyCtrlSpd100 | PhyCtrlSpd10);
+ phy_ctrl |= PhyCtrlAne | PhyCtrlReset;
+
+ switch (media) {
+ default:
+ case AUTOSELECT:
+ phy_ctrl |= PhyCtrlDux | PhyCtrlSpd100 | PhyCtrlSpd10;
+ break;
+ case M10_HALF:
+ phy_ctrl |= PhyCtrlSpd10;
+ break;
+ case M10_FULL:
+ phy_ctrl |= PhyCtrlDux | PhyCtrlSpd10;
+ break;
+ case M100_HALF:
+ phy_ctrl |= PhyCtrlSpd100;
+ break;
+ case M100_FULL:
+ phy_ctrl |= PhyCtrlDux | PhyCtrlSpd100;
+ break;
+ }
+
+ iowrite32(phy_ctrl, port_base + PhyCtrl);
+ mdelay(10);
+
+ phy_ctrl &= ~PhyCtrlReset;
+ iowrite32(phy_ctrl, port_base + PhyCtrl);
+ mdelay(1);
+
+ _sc92031_mii_write(port_base, MII_JAB,
+ PHY_16_JAB_ENB | PHY_16_PORT_ENB);
+ _sc92031_mii_scan(port_base);
+
+ netif_carrier_off(dev);
+ netif_stop_queue(dev);
+}
+
+static void _sc92031_reset(struct net_device *dev)
+{
+ struct sc92031_priv *priv = netdev_priv(dev);
+ void __iomem *port_base = priv->port_base;
+
+ /* disable PM */
+ iowrite32(0, port_base + PMConfig);
+
+ /* soft reset the chip */
+ iowrite32(Cfg0_Reset, port_base + Config0);
+ mdelay(200);
+
+ iowrite32(0, port_base + Config0);
+ mdelay(10);
+
+ /* disable interrupts */
+ iowrite32(0, port_base + IntrMask);
+
+ /* clear multicast address */
+ iowrite32(0, port_base + MAR0);
+ iowrite32(0, port_base + MAR0 + 4);
+
+ /* init rx ring */
+ iowrite32(priv->rx_ring_dma_addr, port_base + RxbufAddr);
+ priv->rx_ring_tail = priv->rx_ring_dma_addr;
+
+ /* init tx ring */
+ _sc92031_tx_clear(dev);
+
+ /* clear old register values */
+ priv->intr_status = 0;
+ atomic_set(&priv->intr_mask, 0);
+ priv->rx_config = 0;
+ priv->tx_config = 0;
+ priv->mc_flags = 0;
+
+ /* configure rx buffer size */
+ /* NOTE: vendor driver had dead code here to enable early tx/rx */
+ iowrite32(Cfg1_Rcv64K, port_base + Config1);
+
+ _sc92031_phy_reset(dev);
+ _sc92031_check_media(dev);
+
+ /* calculate rx fifo overflow */
+ priv->rx_value = 0;
+
+ /* enable PM */
+ iowrite32(priv->pm_config, port_base + PMConfig);
+
+ /* clear intr register */
+ ioread32(port_base + IntrStatus);
+}
+
+static void _sc92031_tx_tasklet(struct net_device *dev)
+{
+ struct sc92031_priv *priv = netdev_priv(dev);
+ void __iomem *port_base = priv->port_base;
+
+ unsigned old_tx_tail;
+ unsigned entry;
+ u32 tx_status;
+
+ old_tx_tail = priv->tx_tail;
+ while (priv->tx_head - priv->tx_tail > 0) {
+ entry = priv->tx_tail % NUM_TX_DESC;
+ tx_status = ioread32(port_base + TxStatus0 + entry * 4);
+
+ if (!(tx_status & (TxStatOK | TxUnderrun | TxAborted)))
+ break;
+
+ priv->tx_tail++;
+
+ if (tx_status & TxStatOK) {
+ dev->stats.tx_bytes += tx_status & 0x1fff;
+ dev->stats.tx_packets++;
+ /* Note: TxCarrierLost is always asserted at 100mbps. */
+ dev->stats.collisions += (tx_status >> 22) & 0xf;
+ }
+
+ if (tx_status & (TxOutOfWindow | TxAborted)) {
+ dev->stats.tx_errors++;
+
+ if (tx_status & TxAborted)
+ dev->stats.tx_aborted_errors++;
+
+ if (tx_status & TxCarrierLost)
+ dev->stats.tx_carrier_errors++;
+
+ if (tx_status & TxOutOfWindow)
+ dev->stats.tx_window_errors++;
+ }
+
+ if (tx_status & TxUnderrun)
+ dev->stats.tx_fifo_errors++;
+ }
+
+ if (priv->tx_tail != old_tx_tail)
+ if (netif_queue_stopped(dev))
+ netif_wake_queue(dev);
+}
+
+static void _sc92031_rx_tasklet_error(struct net_device *dev,
+ u32 rx_status, unsigned rx_size)
+{
+ if(rx_size > (MAX_ETH_FRAME_SIZE + 4) || rx_size < 16) {
+ dev->stats.rx_errors++;
+ dev->stats.rx_length_errors++;
+ }
+
+ if (!(rx_status & RxStatesOK)) {
+ dev->stats.rx_errors++;
+
+ if (rx_status & (RxHugeFrame | RxSmallFrame))
+ dev->stats.rx_length_errors++;
+
+ if (rx_status & RxBadAlign)
+ dev->stats.rx_frame_errors++;
+
+ if (!(rx_status & RxCRCOK))
+ dev->stats.rx_crc_errors++;
+ } else {
+ struct sc92031_priv *priv = netdev_priv(dev);
+ priv->rx_loss++;
+ }
+}
+
+static void _sc92031_rx_tasklet(struct net_device *dev)
+{
+ struct sc92031_priv *priv = netdev_priv(dev);
+ void __iomem *port_base = priv->port_base;
+
+ dma_addr_t rx_ring_head;
+ unsigned rx_len;
+ unsigned rx_ring_offset;
+ void *rx_ring = priv->rx_ring;
+
+ rx_ring_head = ioread32(port_base + RxBufWPtr);
+ rmb();
+
+ /* rx_ring_head is only 17 bits in the RxBufWPtr register.
+ * we need to change it to 32 bits physical address
+ */
+ rx_ring_head &= (dma_addr_t)(RX_BUF_LEN - 1);
+ rx_ring_head |= priv->rx_ring_dma_addr & ~(dma_addr_t)(RX_BUF_LEN - 1);
+ if (rx_ring_head < priv->rx_ring_dma_addr)
+ rx_ring_head += RX_BUF_LEN;
+
+ if (rx_ring_head >= priv->rx_ring_tail)
+ rx_len = rx_ring_head - priv->rx_ring_tail;
+ else
+ rx_len = RX_BUF_LEN - (priv->rx_ring_tail - rx_ring_head);
+
+ if (!rx_len)
+ return;
+
+ if (unlikely(rx_len > RX_BUF_LEN)) {
+ if (printk_ratelimit())
+ printk(KERN_ERR "%s: rx packets length > rx buffer\n",
+ dev->name);
+ return;
+ }
+
+ rx_ring_offset = (priv->rx_ring_tail - priv->rx_ring_dma_addr) % RX_BUF_LEN;
+
+ while (rx_len) {
+ u32 rx_status;
+ unsigned rx_size, rx_size_align, pkt_size;
+ struct sk_buff *skb;
+
+ rx_status = le32_to_cpup((__le32 *)(rx_ring + rx_ring_offset));
+ rmb();
+
+ rx_size = rx_status >> 20;
+ rx_size_align = (rx_size + 3) & ~3; // for 4 bytes aligned
+ pkt_size = rx_size - 4; // Omit the four octet CRC from the length.
+
+ rx_ring_offset = (rx_ring_offset + 4) % RX_BUF_LEN;
+
+ if (unlikely(rx_status == 0 ||
+ rx_size > (MAX_ETH_FRAME_SIZE + 4) ||
+ rx_size < 16 ||
+ !(rx_status & RxStatesOK))) {
+ _sc92031_rx_tasklet_error(dev, rx_status, rx_size);
+ break;
+ }
+
+ if (unlikely(rx_size_align + 4 > rx_len)) {
+ if (printk_ratelimit())
+ printk(KERN_ERR "%s: rx_len is too small\n", dev->name);
+ break;
+ }
+
+ rx_len -= rx_size_align + 4;
+
+ skb = netdev_alloc_skb_ip_align(dev, pkt_size);
+ if (unlikely(!skb)) {
+ if (printk_ratelimit())
+ printk(KERN_ERR "%s: Couldn't allocate a skb_buff for a packet of size %u\n",
+ dev->name, pkt_size);
+ goto next;
+ }
+
+ if ((rx_ring_offset + pkt_size) > RX_BUF_LEN) {
+ memcpy(skb_put(skb, RX_BUF_LEN - rx_ring_offset),
+ rx_ring + rx_ring_offset, RX_BUF_LEN - rx_ring_offset);
+ memcpy(skb_put(skb, pkt_size - (RX_BUF_LEN - rx_ring_offset)),
+ rx_ring, pkt_size - (RX_BUF_LEN - rx_ring_offset));
+ } else {
+ memcpy(skb_put(skb, pkt_size), rx_ring + rx_ring_offset, pkt_size);
+ }
+
+ skb->protocol = eth_type_trans(skb, dev);
+ netif_rx(skb);
+
+ dev->stats.rx_bytes += pkt_size;
+ dev->stats.rx_packets++;
+
+ if (rx_status & Rx_Multicast)
+ dev->stats.multicast++;
+
+ next:
+ rx_ring_offset = (rx_ring_offset + rx_size_align) % RX_BUF_LEN;
+ }
+ mb();
+
+ priv->rx_ring_tail = rx_ring_head;
+ iowrite32(priv->rx_ring_tail, port_base + RxBufRPtr);
+}
+
+static void _sc92031_link_tasklet(struct net_device *dev)
+{
+ if (_sc92031_check_media(dev))
+ netif_wake_queue(dev);
+ else {
+ netif_stop_queue(dev);
+ dev->stats.tx_carrier_errors++;
+ }
+}
+
+static void sc92031_tasklet(unsigned long data)
+{
+ struct net_device *dev = (struct net_device *)data;
+ struct sc92031_priv *priv = netdev_priv(dev);
+ void __iomem *port_base = priv->port_base;
+ u32 intr_status, intr_mask;
+
+ intr_status = priv->intr_status;
+
+ spin_lock(&priv->lock);
+
+ if (unlikely(!netif_running(dev)))
+ goto out;
+
+ if (intr_status & TxOK)
+ _sc92031_tx_tasklet(dev);
+
+ if (intr_status & RxOK)
+ _sc92031_rx_tasklet(dev);
+
+ if (intr_status & RxOverflow)
+ dev->stats.rx_errors++;
+
+ if (intr_status & TimeOut) {
+ dev->stats.rx_errors++;
+ dev->stats.rx_length_errors++;
+ }
+
+ if (intr_status & (LinkFail | LinkOK))
+ _sc92031_link_tasklet(dev);
+
+out:
+ intr_mask = atomic_read(&priv->intr_mask);
+ rmb();
+
+ iowrite32(intr_mask, port_base + IntrMask);
+ mmiowb();
+
+ spin_unlock(&priv->lock);
+}
+
+static irqreturn_t sc92031_interrupt(int irq, void *dev_id)
+{
+ struct net_device *dev = dev_id;
+ struct sc92031_priv *priv = netdev_priv(dev);
+ void __iomem *port_base = priv->port_base;
+ u32 intr_status, intr_mask;
+
+ /* mask interrupts before clearing IntrStatus */
+ iowrite32(0, port_base + IntrMask);
+ _sc92031_dummy_read(port_base);
+
+ intr_status = ioread32(port_base + IntrStatus);
+ if (unlikely(intr_status == 0xffffffff))
+ return IRQ_NONE; // hardware has gone missing
+
+ intr_status &= IntrBits;
+ if (!intr_status)
+ goto out_none;
+
+ priv->intr_status = intr_status;
+ tasklet_schedule(&priv->tasklet);
+
+ return IRQ_HANDLED;
+
+out_none:
+ intr_mask = atomic_read(&priv->intr_mask);
+ rmb();
+
+ iowrite32(intr_mask, port_base + IntrMask);
+ mmiowb();
+
+ return IRQ_NONE;
+}
+
+static struct net_device_stats *sc92031_get_stats(struct net_device *dev)
+{
+ struct sc92031_priv *priv = netdev_priv(dev);
+ void __iomem *port_base = priv->port_base;
+
+ // FIXME I do not understand what is this trying to do.
+ if (netif_running(dev)) {
+ int temp;
+
+ spin_lock_bh(&priv->lock);
+
+ /* Update the error count. */
+ temp = (ioread32(port_base + RxStatus0) >> 16) & 0xffff;
+
+ if (temp == 0xffff) {
+ priv->rx_value += temp;
+ dev->stats.rx_fifo_errors = priv->rx_value;
+ } else
+ dev->stats.rx_fifo_errors = temp + priv->rx_value;
+
+ spin_unlock_bh(&priv->lock);
+ }
+
+ return &dev->stats;
+}
+
+static netdev_tx_t sc92031_start_xmit(struct sk_buff *skb,
+ struct net_device *dev)
+{
+ struct sc92031_priv *priv = netdev_priv(dev);
+ void __iomem *port_base = priv->port_base;
+ unsigned len;
+ unsigned entry;
+ u32 tx_status;
+
+ if (unlikely(skb->len > TX_BUF_SIZE)) {
+ dev->stats.tx_dropped++;
+ goto out;
+ }
+
+ spin_lock(&priv->lock);
+
+ if (unlikely(!netif_carrier_ok(dev))) {
+ dev->stats.tx_dropped++;
+ goto out_unlock;
+ }
+
+ BUG_ON(priv->tx_head - priv->tx_tail >= NUM_TX_DESC);
+
+ entry = priv->tx_head++ % NUM_TX_DESC;
+
+ skb_copy_and_csum_dev(skb, priv->tx_bufs + entry * TX_BUF_SIZE);
+
+ len = skb->len;
+ if (len < ETH_ZLEN) {
+ memset(priv->tx_bufs + entry * TX_BUF_SIZE + len,
+ 0, ETH_ZLEN - len);
+ len = ETH_ZLEN;
+ }
+
+ wmb();
+
+ if (len < 100)
+ tx_status = len;
+ else if (len < 300)
+ tx_status = 0x30000 | len;
+ else
+ tx_status = 0x50000 | len;
+
+ iowrite32(priv->tx_bufs_dma_addr + entry * TX_BUF_SIZE,
+ port_base + TxAddr0 + entry * 4);
+ iowrite32(tx_status, port_base + TxStatus0 + entry * 4);
+ mmiowb();
+
+ if (priv->tx_head - priv->tx_tail >= NUM_TX_DESC)
+ netif_stop_queue(dev);
+
+out_unlock:
+ spin_unlock(&priv->lock);
+
+out:
+ dev_kfree_skb(skb);
+
+ return NETDEV_TX_OK;
+}
+
+static int sc92031_open(struct net_device *dev)
+{
+ int err;
+ struct sc92031_priv *priv = netdev_priv(dev);
+ struct pci_dev *pdev = priv->pdev;
+
+ priv->rx_ring = pci_alloc_consistent(pdev, RX_BUF_LEN,
+ &priv->rx_ring_dma_addr);
+ if (unlikely(!priv->rx_ring)) {
+ err = -ENOMEM;
+ goto out_alloc_rx_ring;
+ }
+
+ priv->tx_bufs = pci_alloc_consistent(pdev, TX_BUF_TOT_LEN,
+ &priv->tx_bufs_dma_addr);
+ if (unlikely(!priv->tx_bufs)) {
+ err = -ENOMEM;
+ goto out_alloc_tx_bufs;
+ }
+ priv->tx_head = priv->tx_tail = 0;
+
+ err = request_irq(pdev->irq, sc92031_interrupt,
+ IRQF_SHARED, dev->name, dev);
+ if (unlikely(err < 0))
+ goto out_request_irq;
+
+ priv->pm_config = 0;
+
+ /* Interrupts already disabled by sc92031_stop or sc92031_probe */
+ spin_lock_bh(&priv->lock);
+
+ _sc92031_reset(dev);
+ mmiowb();
+
+ spin_unlock_bh(&priv->lock);
+ sc92031_enable_interrupts(dev);
+
+ if (netif_carrier_ok(dev))
+ netif_start_queue(dev);
+ else
+ netif_tx_disable(dev);
+
+ return 0;
+
+out_request_irq:
+ pci_free_consistent(pdev, TX_BUF_TOT_LEN, priv->tx_bufs,
+ priv->tx_bufs_dma_addr);
+out_alloc_tx_bufs:
+ pci_free_consistent(pdev, RX_BUF_LEN, priv->rx_ring,
+ priv->rx_ring_dma_addr);
+out_alloc_rx_ring:
+ return err;
+}
+
+static int sc92031_stop(struct net_device *dev)
+{
+ struct sc92031_priv *priv = netdev_priv(dev);
+ struct pci_dev *pdev = priv->pdev;
+
+ netif_tx_disable(dev);
+
+ /* Disable interrupts, stop Tx and Rx. */
+ sc92031_disable_interrupts(dev);
+
+ spin_lock_bh(&priv->lock);
+
+ _sc92031_disable_tx_rx(dev);
+ _sc92031_tx_clear(dev);
+ mmiowb();
+
+ spin_unlock_bh(&priv->lock);
+
+ free_irq(pdev->irq, dev);
+ pci_free_consistent(pdev, TX_BUF_TOT_LEN, priv->tx_bufs,
+ priv->tx_bufs_dma_addr);
+ pci_free_consistent(pdev, RX_BUF_LEN, priv->rx_ring,
+ priv->rx_ring_dma_addr);
+
+ return 0;
+}
+
+static void sc92031_set_multicast_list(struct net_device *dev)
+{
+ struct sc92031_priv *priv = netdev_priv(dev);
+
+ spin_lock_bh(&priv->lock);
+
+ _sc92031_set_mar(dev);
+ _sc92031_set_rx_config(dev);
+ mmiowb();
+
+ spin_unlock_bh(&priv->lock);
+}
+
+static void sc92031_tx_timeout(struct net_device *dev)
+{
+ struct sc92031_priv *priv = netdev_priv(dev);
+
+ /* Disable interrupts by clearing the interrupt mask.*/
+ sc92031_disable_interrupts(dev);
+
+ spin_lock(&priv->lock);
+
+ priv->tx_timeouts++;
+
+ _sc92031_reset(dev);
+ mmiowb();
+
+ spin_unlock(&priv->lock);
+
+ /* enable interrupts */
+ sc92031_enable_interrupts(dev);
+
+ if (netif_carrier_ok(dev))
+ netif_wake_queue(dev);
+}
+
+#ifdef CONFIG_NET_POLL_CONTROLLER
+static void sc92031_poll_controller(struct net_device *dev)
+{
+ disable_irq(dev->irq);
+ if (sc92031_interrupt(dev->irq, dev) != IRQ_NONE)
+ sc92031_tasklet((unsigned long)dev);
+ enable_irq(dev->irq);
+}
+#endif
+
+static int sc92031_ethtool_get_settings(struct net_device *dev,
+ struct ethtool_cmd *cmd)
+{
+ struct sc92031_priv *priv = netdev_priv(dev);
+ void __iomem *port_base = priv->port_base;
+ u8 phy_address;
+ u32 phy_ctrl;
+ u16 output_status;
+
+ spin_lock_bh(&priv->lock);
+
+ phy_address = ioread32(port_base + Miicmd1) >> 27;
+ phy_ctrl = ioread32(port_base + PhyCtrl);
+
+ output_status = _sc92031_mii_read(port_base, MII_OutputStatus);
+ _sc92031_mii_scan(port_base);
+ mmiowb();
+
+ spin_unlock_bh(&priv->lock);
+
+ cmd->supported = SUPPORTED_10baseT_Half | SUPPORTED_10baseT_Full
+ | SUPPORTED_100baseT_Half | SUPPORTED_100baseT_Full
+ | SUPPORTED_Autoneg | SUPPORTED_TP | SUPPORTED_MII;
+
+ cmd->advertising = ADVERTISED_TP | ADVERTISED_MII;
+
+ if ((phy_ctrl & (PhyCtrlDux | PhyCtrlSpd100 | PhyCtrlSpd10))
+ == (PhyCtrlDux | PhyCtrlSpd100 | PhyCtrlSpd10))
+ cmd->advertising |= ADVERTISED_Autoneg;
+
+ if ((phy_ctrl & PhyCtrlSpd10) == PhyCtrlSpd10)
+ cmd->advertising |= ADVERTISED_10baseT_Half;
+
+ if ((phy_ctrl & (PhyCtrlSpd10 | PhyCtrlDux))
+ == (PhyCtrlSpd10 | PhyCtrlDux))
+ cmd->advertising |= ADVERTISED_10baseT_Full;
+
+ if ((phy_ctrl & PhyCtrlSpd100) == PhyCtrlSpd100)
+ cmd->advertising |= ADVERTISED_100baseT_Half;
+
+ if ((phy_ctrl & (PhyCtrlSpd100 | PhyCtrlDux))
+ == (PhyCtrlSpd100 | PhyCtrlDux))
+ cmd->advertising |= ADVERTISED_100baseT_Full;
+
+ if (phy_ctrl & PhyCtrlAne)
+ cmd->advertising |= ADVERTISED_Autoneg;
+
+ ethtool_cmd_speed_set(cmd,
+ (output_status & 0x2) ? SPEED_100 : SPEED_10);
+ cmd->duplex = (output_status & 0x4) ? DUPLEX_FULL : DUPLEX_HALF;
+ cmd->port = PORT_MII;
+ cmd->phy_address = phy_address;
+ cmd->transceiver = XCVR_INTERNAL;
+ cmd->autoneg = (phy_ctrl & PhyCtrlAne) ? AUTONEG_ENABLE : AUTONEG_DISABLE;
+
+ return 0;
+}
+
+static int sc92031_ethtool_set_settings(struct net_device *dev,
+ struct ethtool_cmd *cmd)
+{
+ struct sc92031_priv *priv = netdev_priv(dev);
+ void __iomem *port_base = priv->port_base;
+ u32 speed = ethtool_cmd_speed(cmd);
+ u32 phy_ctrl;
+ u32 old_phy_ctrl;
+
+ if (!(speed == SPEED_10 || speed == SPEED_100))
+ return -EINVAL;
+ if (!(cmd->duplex == DUPLEX_HALF || cmd->duplex == DUPLEX_FULL))
+ return -EINVAL;
+ if (!(cmd->port == PORT_MII))
+ return -EINVAL;
+ if (!(cmd->phy_address == 0x1f))
+ return -EINVAL;
+ if (!(cmd->transceiver == XCVR_INTERNAL))
+ return -EINVAL;
+ if (!(cmd->autoneg == AUTONEG_DISABLE || cmd->autoneg == AUTONEG_ENABLE))
+ return -EINVAL;
+
+ if (cmd->autoneg == AUTONEG_ENABLE) {
+ if (!(cmd->advertising & (ADVERTISED_Autoneg
+ | ADVERTISED_100baseT_Full
+ | ADVERTISED_100baseT_Half
+ | ADVERTISED_10baseT_Full
+ | ADVERTISED_10baseT_Half)))
+ return -EINVAL;
+
+ phy_ctrl = PhyCtrlAne;
+
+ // FIXME: I'm not sure what the original code was trying to do
+ if (cmd->advertising & ADVERTISED_Autoneg)
+ phy_ctrl |= PhyCtrlDux | PhyCtrlSpd100 | PhyCtrlSpd10;
+ if (cmd->advertising & ADVERTISED_100baseT_Full)
+ phy_ctrl |= PhyCtrlDux | PhyCtrlSpd100;
+ if (cmd->advertising & ADVERTISED_100baseT_Half)
+ phy_ctrl |= PhyCtrlSpd100;
+ if (cmd->advertising & ADVERTISED_10baseT_Full)
+ phy_ctrl |= PhyCtrlSpd10 | PhyCtrlDux;
+ if (cmd->advertising & ADVERTISED_10baseT_Half)
+ phy_ctrl |= PhyCtrlSpd10;
+ } else {
+ // FIXME: Whole branch guessed
+ phy_ctrl = 0;
+
+ if (speed == SPEED_10)
+ phy_ctrl |= PhyCtrlSpd10;
+ else /* cmd->speed == SPEED_100 */
+ phy_ctrl |= PhyCtrlSpd100;
+
+ if (cmd->duplex == DUPLEX_FULL)
+ phy_ctrl |= PhyCtrlDux;
+ }
+
+ spin_lock_bh(&priv->lock);
+
+ old_phy_ctrl = ioread32(port_base + PhyCtrl);
+ phy_ctrl |= old_phy_ctrl & ~(PhyCtrlAne | PhyCtrlDux
+ | PhyCtrlSpd100 | PhyCtrlSpd10);
+ if (phy_ctrl != old_phy_ctrl)
+ iowrite32(phy_ctrl, port_base + PhyCtrl);
+
+ spin_unlock_bh(&priv->lock);
+
+ return 0;
+}
+
+static void sc92031_ethtool_get_wol(struct net_device *dev,
+ struct ethtool_wolinfo *wolinfo)
+{
+ struct sc92031_priv *priv = netdev_priv(dev);
+ void __iomem *port_base = priv->port_base;
+ u32 pm_config;
+
+ spin_lock_bh(&priv->lock);
+ pm_config = ioread32(port_base + PMConfig);
+ spin_unlock_bh(&priv->lock);
+
+ // FIXME: Guessed
+ wolinfo->supported = WAKE_PHY | WAKE_MAGIC
+ | WAKE_UCAST | WAKE_MCAST | WAKE_BCAST;
+ wolinfo->wolopts = 0;
+
+ if (pm_config & PM_LinkUp)
+ wolinfo->wolopts |= WAKE_PHY;
+
+ if (pm_config & PM_Magic)
+ wolinfo->wolopts |= WAKE_MAGIC;
+
+ if (pm_config & PM_WakeUp)
+ // FIXME: Guessed
+ wolinfo->wolopts |= WAKE_UCAST | WAKE_MCAST | WAKE_BCAST;
+}
+
+static int sc92031_ethtool_set_wol(struct net_device *dev,
+ struct ethtool_wolinfo *wolinfo)
+{
+ struct sc92031_priv *priv = netdev_priv(dev);
+ void __iomem *port_base = priv->port_base;
+ u32 pm_config;
+
+ spin_lock_bh(&priv->lock);
+
+ pm_config = ioread32(port_base + PMConfig)
+ & ~(PM_LinkUp | PM_Magic | PM_WakeUp);
+
+ if (wolinfo->wolopts & WAKE_PHY)
+ pm_config |= PM_LinkUp;
+
+ if (wolinfo->wolopts & WAKE_MAGIC)
+ pm_config |= PM_Magic;
+
+ // FIXME: Guessed
+ if (wolinfo->wolopts & (WAKE_UCAST | WAKE_MCAST | WAKE_BCAST))
+ pm_config |= PM_WakeUp;
+
+ priv->pm_config = pm_config;
+ iowrite32(pm_config, port_base + PMConfig);
+ mmiowb();
+
+ spin_unlock_bh(&priv->lock);
+
+ return 0;
+}
+
+static int sc92031_ethtool_nway_reset(struct net_device *dev)
+{
+ int err = 0;
+ struct sc92031_priv *priv = netdev_priv(dev);
+ void __iomem *port_base = priv->port_base;
+ u16 bmcr;
+
+ spin_lock_bh(&priv->lock);
+
+ bmcr = _sc92031_mii_read(port_base, MII_BMCR);
+ if (!(bmcr & BMCR_ANENABLE)) {
+ err = -EINVAL;
+ goto out;
+ }
+
+ _sc92031_mii_write(port_base, MII_BMCR, bmcr | BMCR_ANRESTART);
+
+out:
+ _sc92031_mii_scan(port_base);
+ mmiowb();
+
+ spin_unlock_bh(&priv->lock);
+
+ return err;
+}
+
+static const char sc92031_ethtool_stats_strings[SILAN_STATS_NUM][ETH_GSTRING_LEN] = {
+ "tx_timeout",
+ "rx_loss",
+};
+
+static void sc92031_ethtool_get_strings(struct net_device *dev,
+ u32 stringset, u8 *data)
+{
+ if (stringset == ETH_SS_STATS)
+ memcpy(data, sc92031_ethtool_stats_strings,
+ SILAN_STATS_NUM * ETH_GSTRING_LEN);
+}
+
+static int sc92031_ethtool_get_sset_count(struct net_device *dev, int sset)
+{
+ switch (sset) {
+ case ETH_SS_STATS:
+ return SILAN_STATS_NUM;
+ default:
+ return -EOPNOTSUPP;
+ }
+}
+
+static void sc92031_ethtool_get_ethtool_stats(struct net_device *dev,
+ struct ethtool_stats *stats, u64 *data)
+{
+ struct sc92031_priv *priv = netdev_priv(dev);
+
+ spin_lock_bh(&priv->lock);
+ data[0] = priv->tx_timeouts;
+ data[1] = priv->rx_loss;
+ spin_unlock_bh(&priv->lock);
+}
+
+static const struct ethtool_ops sc92031_ethtool_ops = {
+ .get_settings = sc92031_ethtool_get_settings,
+ .set_settings = sc92031_ethtool_set_settings,
+ .get_wol = sc92031_ethtool_get_wol,
+ .set_wol = sc92031_ethtool_set_wol,
+ .nway_reset = sc92031_ethtool_nway_reset,
+ .get_link = ethtool_op_get_link,
+ .get_strings = sc92031_ethtool_get_strings,
+ .get_sset_count = sc92031_ethtool_get_sset_count,
+ .get_ethtool_stats = sc92031_ethtool_get_ethtool_stats,
+};
+
+
+static const struct net_device_ops sc92031_netdev_ops = {
+ .ndo_get_stats = sc92031_get_stats,
+ .ndo_start_xmit = sc92031_start_xmit,
+ .ndo_open = sc92031_open,
+ .ndo_stop = sc92031_stop,
+ .ndo_set_rx_mode = sc92031_set_multicast_list,
+ .ndo_change_mtu = eth_change_mtu,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_set_mac_address = eth_mac_addr,
+ .ndo_tx_timeout = sc92031_tx_timeout,
+#ifdef CONFIG_NET_POLL_CONTROLLER
+ .ndo_poll_controller = sc92031_poll_controller,
+#endif
+};
+
+static int __devinit sc92031_probe(struct pci_dev *pdev,
+ const struct pci_device_id *id)
+{
+ int err;
+ void __iomem* port_base;
+ struct net_device *dev;
+ struct sc92031_priv *priv;
+ u32 mac0, mac1;
+ unsigned long base_addr;
+
+ err = pci_enable_device(pdev);
+ if (unlikely(err < 0))
+ goto out_enable_device;
+
+ pci_set_master(pdev);
+
+ err = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
+ if (unlikely(err < 0))
+ goto out_set_dma_mask;
+
+ err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
+ if (unlikely(err < 0))
+ goto out_set_dma_mask;
+
+ err = pci_request_regions(pdev, SC92031_NAME);
+ if (unlikely(err < 0))
+ goto out_request_regions;
+
+ port_base = pci_iomap(pdev, SC92031_USE_BAR, 0);
+ if (unlikely(!port_base)) {
+ err = -EIO;
+ goto out_iomap;
+ }
+
+ dev = alloc_etherdev(sizeof(struct sc92031_priv));
+ if (unlikely(!dev)) {
+ err = -ENOMEM;
+ goto out_alloc_etherdev;
+ }
+
+ pci_set_drvdata(pdev, dev);
+ SET_NETDEV_DEV(dev, &pdev->dev);
+
+#if SC92031_USE_BAR == 0
+ dev->mem_start = pci_resource_start(pdev, SC92031_USE_BAR);
+ dev->mem_end = pci_resource_end(pdev, SC92031_USE_BAR);
+#elif SC92031_USE_BAR == 1
+ dev->base_addr = pci_resource_start(pdev, SC92031_USE_BAR);
+#endif
+ dev->irq = pdev->irq;
+
+ /* faked with skb_copy_and_csum_dev */
+ dev->features = NETIF_F_SG | NETIF_F_HIGHDMA |
+ NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM;
+
+ dev->netdev_ops = &sc92031_netdev_ops;
+ dev->watchdog_timeo = TX_TIMEOUT;
+ dev->ethtool_ops = &sc92031_ethtool_ops;
+
+ priv = netdev_priv(dev);
+ spin_lock_init(&priv->lock);
+ priv->port_base = port_base;
+ priv->pdev = pdev;
+ tasklet_init(&priv->tasklet, sc92031_tasklet, (unsigned long)dev);
+ /* Fudge tasklet count so the call to sc92031_enable_interrupts at
+ * sc92031_open will work correctly */
+ tasklet_disable_nosync(&priv->tasklet);
+
+ /* PCI PM Wakeup */
+ iowrite32((~PM_LongWF & ~PM_LWPTN) | PM_Enable, port_base + PMConfig);
+
+ mac0 = ioread32(port_base + MAC0);
+ mac1 = ioread32(port_base + MAC0 + 4);
+ dev->dev_addr[0] = dev->perm_addr[0] = mac0 >> 24;
+ dev->dev_addr[1] = dev->perm_addr[1] = mac0 >> 16;
+ dev->dev_addr[2] = dev->perm_addr[2] = mac0 >> 8;
+ dev->dev_addr[3] = dev->perm_addr[3] = mac0;
+ dev->dev_addr[4] = dev->perm_addr[4] = mac1 >> 8;
+ dev->dev_addr[5] = dev->perm_addr[5] = mac1;
+
+ err = register_netdev(dev);
+ if (err < 0)
+ goto out_register_netdev;
+
+#if SC92031_USE_BAR == 0
+ base_addr = dev->mem_start;
+#elif SC92031_USE_BAR == 1
+ base_addr = dev->base_addr;
+#endif
+ printk(KERN_INFO "%s: SC92031 at 0x%lx, %pM, IRQ %d\n", dev->name,
+ base_addr, dev->dev_addr, dev->irq);
+
+ return 0;
+
+out_register_netdev:
+ free_netdev(dev);
+out_alloc_etherdev:
+ pci_iounmap(pdev, port_base);
+out_iomap:
+ pci_release_regions(pdev);
+out_request_regions:
+out_set_dma_mask:
+ pci_disable_device(pdev);
+out_enable_device:
+ return err;
+}
+
+static void __devexit sc92031_remove(struct pci_dev *pdev)
+{
+ struct net_device *dev = pci_get_drvdata(pdev);
+ struct sc92031_priv *priv = netdev_priv(dev);
+ void __iomem* port_base = priv->port_base;
+
+ unregister_netdev(dev);
+ free_netdev(dev);
+ pci_iounmap(pdev, port_base);
+ pci_release_regions(pdev);
+ pci_disable_device(pdev);
+}
+
+static int sc92031_suspend(struct pci_dev *pdev, pm_message_t state)
+{
+ struct net_device *dev = pci_get_drvdata(pdev);
+ struct sc92031_priv *priv = netdev_priv(dev);
+
+ pci_save_state(pdev);
+
+ if (!netif_running(dev))
+ goto out;
+
+ netif_device_detach(dev);
+
+ /* Disable interrupts, stop Tx and Rx. */
+ sc92031_disable_interrupts(dev);
+
+ spin_lock_bh(&priv->lock);
+
+ _sc92031_disable_tx_rx(dev);
+ _sc92031_tx_clear(dev);
+ mmiowb();
+
+ spin_unlock_bh(&priv->lock);
+
+out:
+ pci_set_power_state(pdev, pci_choose_state(pdev, state));
+
+ return 0;
+}
+
+static int sc92031_resume(struct pci_dev *pdev)
+{
+ struct net_device *dev = pci_get_drvdata(pdev);
+ struct sc92031_priv *priv = netdev_priv(dev);
+
+ pci_restore_state(pdev);
+ pci_set_power_state(pdev, PCI_D0);
+
+ if (!netif_running(dev))
+ goto out;
+
+ /* Interrupts already disabled by sc92031_suspend */
+ spin_lock_bh(&priv->lock);
+
+ _sc92031_reset(dev);
+ mmiowb();
+
+ spin_unlock_bh(&priv->lock);
+ sc92031_enable_interrupts(dev);
+
+ netif_device_attach(dev);
+
+ if (netif_carrier_ok(dev))
+ netif_wake_queue(dev);
+ else
+ netif_tx_disable(dev);
+
+out:
+ return 0;
+}
+
+static DEFINE_PCI_DEVICE_TABLE(sc92031_pci_device_id_table) = {
+ { PCI_DEVICE(PCI_VENDOR_ID_SILAN, 0x2031) },
+ { PCI_DEVICE(PCI_VENDOR_ID_SILAN, 0x8139) },
+ { PCI_DEVICE(0x1088, 0x2031) },
+ { 0, }
+};
+MODULE_DEVICE_TABLE(pci, sc92031_pci_device_id_table);
+
+static struct pci_driver sc92031_pci_driver = {
+ .name = SC92031_NAME,
+ .id_table = sc92031_pci_device_id_table,
+ .probe = sc92031_probe,
+ .remove = __devexit_p(sc92031_remove),
+ .suspend = sc92031_suspend,
+ .resume = sc92031_resume,
+};
+
+static int __init sc92031_init(void)
+{
+ return pci_register_driver(&sc92031_pci_driver);
+}
+
+static void __exit sc92031_exit(void)
+{
+ pci_unregister_driver(&sc92031_pci_driver);
+}
+
+module_init(sc92031_init);
+module_exit(sc92031_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Cesar Eduardo Barros <cesarb@cesarb.net>");
+MODULE_DESCRIPTION("Silan SC92031 PCI Fast Ethernet Adapter driver");