diff options
Diffstat (limited to 'drivers/net/fddi/Kconfig')
| -rw-r--r-- | drivers/net/fddi/Kconfig | 77 |
1 files changed, 77 insertions, 0 deletions
diff --git a/drivers/net/fddi/Kconfig b/drivers/net/fddi/Kconfig new file mode 100644 index 00000000000..3a424c864f4 --- /dev/null +++ b/drivers/net/fddi/Kconfig @@ -0,0 +1,77 @@ +# +# FDDI network device configuration +# + +config FDDI + tristate "FDDI driver support" + depends on PCI || EISA || TC + ---help--- + Fiber Distributed Data Interface is a high speed local area network + design; essentially a replacement for high speed Ethernet. FDDI can + run over copper or fiber. If you are connected to such a network and + want a driver for the FDDI card in your computer, say Y here (and + then also Y to the driver for your FDDI card, below). Most people + will say N. + +if FDDI + +config DEFXX + tristate "Digital DEFTA/DEFEA/DEFPA adapter support" + depends on FDDI && (PCI || EISA || TC) + ---help--- + This is support for the DIGITAL series of TURBOchannel (DEFTA), + EISA (DEFEA) and PCI (DEFPA) controllers which can connect you + to a local FDDI network. + + To compile this driver as a module, choose M here: the module + will be called defxx. If unsure, say N. + +config DEFXX_MMIO + bool + prompt "Use MMIO instead of PIO" if PCI || EISA + depends on DEFXX + default n if PCI || EISA + default y + ---help--- + This instructs the driver to use EISA or PCI memory-mapped I/O + (MMIO) as appropriate instead of programmed I/O ports (PIO). + Enabling this gives an improvement in processing time in parts + of the driver, but it may cause problems with EISA (DEFEA) + adapters. TURBOchannel does not have the concept of I/O ports, + so MMIO is always used for these (DEFTA) adapters. + + If unsure, say N. + +config SKFP + tristate "SysKonnect FDDI PCI support" + depends on FDDI && PCI + select BITREVERSE + ---help--- + Say Y here if you have a SysKonnect FDDI PCI adapter. + The following adapters are supported by this driver: + - SK-5521 (SK-NET FDDI-UP) + - SK-5522 (SK-NET FDDI-UP DAS) + - SK-5541 (SK-NET FDDI-FP) + - SK-5543 (SK-NET FDDI-LP) + - SK-5544 (SK-NET FDDI-LP DAS) + - SK-5821 (SK-NET FDDI-UP64) + - SK-5822 (SK-NET FDDI-UP64 DAS) + - SK-5841 (SK-NET FDDI-FP64) + - SK-5843 (SK-NET FDDI-LP64) + - SK-5844 (SK-NET FDDI-LP64 DAS) + - Netelligent 100 FDDI DAS Fibre SC + - Netelligent 100 FDDI SAS Fibre SC + - Netelligent 100 FDDI DAS UTP + - Netelligent 100 FDDI SAS UTP + - Netelligent 100 FDDI SAS Fibre MIC + + Read <file:Documentation/networking/skfp.txt> for information about + the driver. + + Questions concerning this driver can be addressed to: + <linux@syskonnect.de> + + To compile this driver as a module, choose M here: the module + will be called skfp. This is recommended. + +endif # FDDI |