diff options
Diffstat (limited to 'drivers/net/gianfar.c')
| -rw-r--r-- | drivers/net/gianfar.c | 1849 |
1 files changed, 1849 insertions, 0 deletions
diff --git a/drivers/net/gianfar.c b/drivers/net/gianfar.c new file mode 100644 index 00000000000..b43b2b11aac --- /dev/null +++ b/drivers/net/gianfar.c @@ -0,0 +1,1849 @@ +/* + * drivers/net/gianfar.c + * + * Gianfar Ethernet Driver + * Driver for FEC on MPC8540 and TSEC on MPC8540/MPC8560 + * Based on 8260_io/fcc_enet.c + * + * Author: Andy Fleming + * Maintainer: Kumar Gala (kumar.gala@freescale.com) + * + * Copyright (c) 2002-2004 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + * Gianfar: AKA Lambda Draconis, "Dragon" + * RA 11 31 24.2 + * Dec +69 19 52 + * V 3.84 + * B-V +1.62 + * + * Theory of operation + * This driver is designed for the Triple-speed Ethernet + * controllers on the Freescale 8540/8560 integrated processors, + * as well as the Fast Ethernet Controller on the 8540. + * + * The driver is initialized through platform_device. Structures which + * define the configuration needed by the board are defined in a + * board structure in arch/ppc/platforms (though I do not + * discount the possibility that other architectures could one + * day be supported. One assumption the driver currently makes + * is that the PHY is configured in such a way to advertise all + * capabilities. This is a sensible default, and on certain + * PHYs, changing this default encounters substantial errata + * issues. Future versions may remove this requirement, but for + * now, it is best for the firmware to ensure this is the case. + * + * The Gianfar Ethernet Controller uses a ring of buffer + * descriptors. The beginning is indicated by a register + * pointing to the physical address of the start of the ring. + * The end is determined by a "wrap" bit being set in the + * last descriptor of the ring. + * + * When a packet is received, the RXF bit in the + * IEVENT register is set, triggering an interrupt when the + * corresponding bit in the IMASK register is also set (if + * interrupt coalescing is active, then the interrupt may not + * happen immediately, but will wait until either a set number + * of frames or amount of time have passed.). In NAPI, the + * interrupt handler will signal there is work to be done, and + * exit. Without NAPI, the packet(s) will be handled + * immediately. Both methods will start at the last known empty + * descriptor, and process every subsequent descriptor until there + * are none left with data (NAPI will stop after a set number of + * packets to give time to other tasks, but will eventually + * process all the packets). The data arrives inside a + * pre-allocated skb, and so after the skb is passed up to the + * stack, a new skb must be allocated, and the address field in + * the buffer descriptor must be updated to indicate this new + * skb. + * + * When the kernel requests that a packet be transmitted, the + * driver starts where it left off last time, and points the + * descriptor at the buffer which was passed in. The driver + * then informs the DMA engine that there are packets ready to + * be transmitted. Once the controller is finished transmitting + * the packet, an interrupt may be triggered (under the same + * conditions as for reception, but depending on the TXF bit). + * The driver then cleans up the buffer. + */ + +#include <linux/config.h> +#include <linux/kernel.h> +#include <linux/sched.h> +#include <linux/string.h> +#include <linux/errno.h> +#include <linux/slab.h> +#include <linux/interrupt.h> +#include <linux/init.h> +#include <linux/delay.h> +#include <linux/netdevice.h> +#include <linux/etherdevice.h> +#include <linux/skbuff.h> +#include <linux/spinlock.h> +#include <linux/mm.h> +#include <linux/device.h> + +#include <asm/io.h> +#include <asm/irq.h> +#include <asm/uaccess.h> +#include <linux/module.h> +#include <linux/version.h> +#include <linux/dma-mapping.h> +#include <linux/crc32.h> + +#include "gianfar.h" +#include "gianfar_phy.h" + +#define TX_TIMEOUT (1*HZ) +#define SKB_ALLOC_TIMEOUT 1000000 +#undef BRIEF_GFAR_ERRORS +#undef VERBOSE_GFAR_ERRORS + +#ifdef CONFIG_GFAR_NAPI +#define RECEIVE(x) netif_receive_skb(x) +#else +#define RECEIVE(x) netif_rx(x) +#endif + +const char gfar_driver_name[] = "Gianfar Ethernet"; +const char gfar_driver_version[] = "1.1"; + +int startup_gfar(struct net_device *dev); +static int gfar_enet_open(struct net_device *dev); +static int gfar_start_xmit(struct sk_buff *skb, struct net_device *dev); +static void gfar_timeout(struct net_device *dev); +static int gfar_close(struct net_device *dev); +struct sk_buff *gfar_new_skb(struct net_device *dev, struct rxbd8 *bdp); +static struct net_device_stats *gfar_get_stats(struct net_device *dev); +static int gfar_set_mac_address(struct net_device *dev); +static int gfar_change_mtu(struct net_device *dev, int new_mtu); +static irqreturn_t gfar_error(int irq, void *dev_id, struct pt_regs *regs); +static irqreturn_t gfar_transmit(int irq, void *dev_id, struct pt_regs *regs); +irqreturn_t gfar_receive(int irq, void *dev_id, struct pt_regs *regs); +static irqreturn_t gfar_interrupt(int irq, void *dev_id, struct pt_regs *regs); +static irqreturn_t phy_interrupt(int irq, void *dev_id, struct pt_regs *regs); +static void gfar_phy_change(void *data); +static void gfar_phy_timer(unsigned long data); +static void adjust_link(struct net_device *dev); +static void init_registers(struct net_device *dev); +static int init_phy(struct net_device *dev); +static int gfar_probe(struct device *device); +static int gfar_remove(struct device *device); +void free_skb_resources(struct gfar_private *priv); +static void gfar_set_multi(struct net_device *dev); +static void gfar_set_hash_for_addr(struct net_device *dev, u8 *addr); +#ifdef CONFIG_GFAR_NAPI +static int gfar_poll(struct net_device *dev, int *budget); +#endif +static int gfar_clean_rx_ring(struct net_device *dev, int rx_work_limit); +static int gfar_process_frame(struct net_device *dev, struct sk_buff *skb, int length); +static void gfar_phy_startup_timer(unsigned long data); + +extern struct ethtool_ops gfar_ethtool_ops; + +MODULE_AUTHOR("Freescale Semiconductor, Inc"); +MODULE_DESCRIPTION("Gianfar Ethernet Driver"); +MODULE_LICENSE("GPL"); + +static int gfar_probe(struct device *device) +{ + u32 tempval; + struct net_device *dev = NULL; + struct gfar_private *priv = NULL; + struct platform_device *pdev = to_platform_device(device); + struct gianfar_platform_data *einfo; + struct resource *r; + int idx; + int err = 0; + int dev_ethtool_ops = 0; + + einfo = (struct gianfar_platform_data *) pdev->dev.platform_data; + + if (einfo == NULL) { + printk(KERN_ERR "gfar %d: Missing additional data!\n", + pdev->id); + + return -ENODEV; + } + + /* Create an ethernet device instance */ + dev = alloc_etherdev(sizeof (*priv)); + + if (dev == NULL) + return -ENOMEM; + + priv = netdev_priv(dev); + + /* Set the info in the priv to the current info */ + priv->einfo = einfo; + + /* fill out IRQ fields */ + if (einfo->device_flags & FSL_GIANFAR_DEV_HAS_MULTI_INTR) { + priv->interruptTransmit = platform_get_irq_byname(pdev, "tx"); + priv->interruptReceive = platform_get_irq_byname(pdev, "rx"); + priv->interruptError = platform_get_irq_byname(pdev, "error"); + } else { + priv->interruptTransmit = platform_get_irq(pdev, 0); + } + + /* get a pointer to the register memory */ + r = platform_get_resource(pdev, IORESOURCE_MEM, 0); + priv->regs = (struct gfar *) + ioremap(r->start, sizeof (struct gfar)); + + if (priv->regs == NULL) { + err = -ENOMEM; + goto regs_fail; + } + + /* Set the PHY base address */ + priv->phyregs = (struct gfar *) + ioremap(einfo->phy_reg_addr, sizeof (struct gfar)); + + if (priv->phyregs == NULL) { + err = -ENOMEM; + goto phy_regs_fail; + } + + spin_lock_init(&priv->lock); + + dev_set_drvdata(device, dev); + + /* Stop the DMA engine now, in case it was running before */ + /* (The firmware could have used it, and left it running). */ + /* To do this, we write Graceful Receive Stop and Graceful */ + /* Transmit Stop, and then wait until the corresponding bits */ + /* in IEVENT indicate the stops have completed. */ + tempval = gfar_read(&priv->regs->dmactrl); + tempval &= ~(DMACTRL_GRS | DMACTRL_GTS); + gfar_write(&priv->regs->dmactrl, tempval); + + tempval = gfar_read(&priv->regs->dmactrl); + tempval |= (DMACTRL_GRS | DMACTRL_GTS); + gfar_write(&priv->regs->dmactrl, tempval); + + while (!(gfar_read(&priv->regs->ievent) & (IEVENT_GRSC | IEVENT_GTSC))) + cpu_relax(); + + /* Reset MAC layer */ + gfar_write(&priv->regs->maccfg1, MACCFG1_SOFT_RESET); + + tempval = (MACCFG1_TX_FLOW | MACCFG1_RX_FLOW); + gfar_write(&priv->regs->maccfg1, tempval); + + /* Initialize MACCFG2. */ + gfar_write(&priv->regs->maccfg2, MACCFG2_INIT_SETTINGS); + + /* Initialize ECNTRL */ + gfar_write(&priv->regs->ecntrl, ECNTRL_INIT_SETTINGS); + + /* Copy the station address into the dev structure, */ + memcpy(dev->dev_addr, einfo->mac_addr, MAC_ADDR_LEN); + + /* Set the dev->base_addr to the gfar reg region */ + dev->base_addr = (unsigned long) (priv->regs); + + SET_MODULE_OWNER(dev); + SET_NETDEV_DEV(dev, device); + + /* Fill in the dev structure */ + dev->open = gfar_enet_open; + dev->hard_start_xmit = gfar_start_xmit; + dev->tx_timeout = gfar_timeout; + dev->watchdog_timeo = TX_TIMEOUT; +#ifdef CONFIG_GFAR_NAPI + dev->poll = gfar_poll; + dev->weight = GFAR_DEV_WEIGHT; +#endif + dev->stop = gfar_close; + dev->get_stats = gfar_get_stats; + dev->change_mtu = gfar_change_mtu; + dev->mtu = 1500; + dev->set_multicast_list = gfar_set_multi; + + /* Index into the array of possible ethtool + * ops to catch all 4 possibilities */ + if((priv->einfo->device_flags & FSL_GIANFAR_DEV_HAS_RMON) == 0) + dev_ethtool_ops += 1; + + if((priv->einfo->device_flags & FSL_GIANFAR_DEV_HAS_COALESCE) == 0) + dev_ethtool_ops += 2; + + dev->ethtool_ops = gfar_op_array[dev_ethtool_ops]; + + priv->rx_buffer_size = DEFAULT_RX_BUFFER_SIZE; +#ifdef CONFIG_GFAR_BUFSTASH + priv->rx_stash_size = STASH_LENGTH; +#endif + priv->tx_ring_size = DEFAULT_TX_RING_SIZE; + priv->rx_ring_size = DEFAULT_RX_RING_SIZE; + + priv->txcoalescing = DEFAULT_TX_COALESCE; + priv->txcount = DEFAULT_TXCOUNT; + priv->txtime = DEFAULT_TXTIME; + priv->rxcoalescing = DEFAULT_RX_COALESCE; + priv->rxcount = DEFAULT_RXCOUNT; + priv->rxtime = DEFAULT_RXTIME; + + err = register_netdev(dev); + + if (err) { + printk(KERN_ERR "%s: Cannot register net device, aborting.\n", + dev->name); + goto register_fail; + } + + /* Print out the device info */ + printk(KERN_INFO DEVICE_NAME, dev->name); + for (idx = 0; idx < 6; idx++) + printk("%2.2x%c", dev->dev_addr[idx], idx == 5 ? ' ' : ':'); + printk("\n"); + + /* Even more device info helps when determining which kernel */ + /* provided which set of benchmarks. Since this is global for all */ + /* devices, we only print it once */ +#ifdef CONFIG_GFAR_NAPI + printk(KERN_INFO "%s: Running with NAPI enabled\n", dev->name); +#else + printk(KERN_INFO "%s: Running with NAPI disabled\n", dev->name); +#endif + printk(KERN_INFO "%s: %d/%d RX/TX BD ring size\n", + dev->name, priv->rx_ring_size, priv->tx_ring_size); + + return 0; + +register_fail: + iounmap((void *) priv->phyregs); +phy_regs_fail: + iounmap((void *) priv->regs); +regs_fail: + free_netdev(dev); + return -ENOMEM; +} + +static int gfar_remove(struct device *device) +{ + struct net_device *dev = dev_get_drvdata(device); + struct gfar_private *priv = netdev_priv(dev); + + dev_set_drvdata(device, NULL); + + iounmap((void *) priv->regs); + iounmap((void *) priv->phyregs); + free_netdev(dev); + + return 0; +} + + +/* Configure the PHY for dev. + * returns 0 if success. -1 if failure + */ +static int init_phy(struct net_device *dev) +{ + struct gfar_private *priv = netdev_priv(dev); + struct phy_info *curphy; + unsigned int timeout = PHY_INIT_TIMEOUT; + struct gfar *phyregs = priv->phyregs; + struct gfar_mii_info *mii_info; + int err; + + priv->oldlink = 0; + priv->oldspeed = 0; + priv->oldduplex = -1; + + mii_info = kmalloc(sizeof(struct gfar_mii_info), + GFP_KERNEL); + + if(NULL == mii_info) { + printk(KERN_ERR "%s: Could not allocate mii_info\n", + dev->name); + return -ENOMEM; + } + + mii_info->speed = SPEED_1000; + mii_info->duplex = DUPLEX_FULL; + mii_info->pause = 0; + mii_info->link = 1; + + mii_info->advertising = (ADVERTISED_10baseT_Half | + ADVERTISED_10baseT_Full | + ADVERTISED_100baseT_Half | + ADVERTISED_100baseT_Full | + ADVERTISED_1000baseT_Full); + mii_info->autoneg = 1; + + spin_lock_init(&mii_info->mdio_lock); + + mii_info->mii_id = priv->einfo->phyid; + + mii_info->dev = dev; + + mii_info->mdio_read = &read_phy_reg; + mii_info->mdio_write = &write_phy_reg; + + priv->mii_info = mii_info; + + /* Reset the management interface */ + gfar_write(&phyregs->miimcfg, MIIMCFG_RESET); + + /* Setup the MII Mgmt clock speed */ + gfar_write(&phyregs->miimcfg, MIIMCFG_INIT_VALUE); + + /* Wait until the bus is free */ + while ((gfar_read(&phyregs->miimind) & MIIMIND_BUSY) && + timeout--) + cpu_relax(); + + if(timeout <= 0) { + printk(KERN_ERR "%s: The MII Bus is stuck!\n", + dev->name); + err = -1; + goto bus_fail; + } + + /* get info for this PHY */ + curphy = get_phy_info(priv->mii_info); + + if (curphy == NULL) { + printk(KERN_ERR "%s: No PHY found\n", dev->name); + err = -1; + goto no_phy; + } + + mii_info->phyinfo = curphy; + + /* Run the commands which initialize the PHY */ + if(curphy->init) { + err = curphy->init(priv->mii_info); + + if (err) + goto phy_init_fail; + } + + return 0; + +phy_init_fail: +no_phy: +bus_fail: + kfree(mii_info); + + return err; +} + +static void init_registers(struct net_device *dev) +{ + struct gfar_private *priv = netdev_priv(dev); + + /* Clear IEVENT */ + gfar_write(&priv->regs->ievent, IEVENT_INIT_CLEAR); + + /* Initialize IMASK */ + gfar_write(&priv->regs->imask, IMASK_INIT_CLEAR); + + /* Init hash registers to zero */ + gfar_write(&priv->regs->iaddr0, 0); + gfar_write(&priv->regs->iaddr1, 0); + gfar_write(&priv->regs->iaddr2, 0); + gfar_write(&priv->regs->iaddr3, 0); + gfar_write(&priv->regs->iaddr4, 0); + gfar_write(&priv->regs->iaddr5, 0); + gfar_write(&priv->regs->iaddr6, 0); + gfar_write(&priv->regs->iaddr7, 0); + + gfar_write(&priv->regs->gaddr0, 0); + gfar_write(&priv->regs->gaddr1, 0); + gfar_write(&priv->regs->gaddr2, 0); + gfar_write(&priv->regs->gaddr3, 0); + gfar_write(&priv->regs->gaddr4, 0); + gfar_write(&priv->regs->gaddr5, 0); + gfar_write(&priv->regs->gaddr6, 0); + gfar_write(&priv->regs->gaddr7, 0); + + /* Zero out rctrl */ + gfar_write(&priv->regs->rctrl, 0x00000000); + + /* Zero out the rmon mib registers if it has them */ + if (priv->einfo->device_flags & FSL_GIANFAR_DEV_HAS_RMON) { + memset((void *) &(priv->regs->rmon), 0, + sizeof (struct rmon_mib)); + + /* Mask off the CAM interrupts */ + gfar_write(&priv->regs->rmon.cam1, 0xffffffff); + gfar_write(&priv->regs->rmon.cam2, 0xffffffff); + } + + /* Initialize the max receive buffer length */ + gfar_write(&priv->regs->mrblr, priv->rx_buffer_size); + +#ifdef CONFIG_GFAR_BUFSTASH + /* If we are stashing buffers, we need to set the + * extraction length to the size of the buffer */ + gfar_write(&priv->regs->attreli, priv->rx_stash_size << 16); +#endif + + /* Initialize the Minimum Frame Length Register */ + gfar_write(&priv->regs->minflr, MINFLR_INIT_SETTINGS); + + /* Setup Attributes so that snooping is on for rx */ + gfar_write(&priv->regs->attr, ATTR_INIT_SETTINGS); + gfar_write(&priv->regs->attreli, ATTRELI_INIT_SETTINGS); + + /* Assign the TBI an address which won't conflict with the PHYs */ + gfar_write(&priv->regs->tbipa, TBIPA_VALUE); +} + +void stop_gfar(struct net_device *dev) +{ + struct gfar_private *priv = netdev_priv(dev); + struct gfar *regs = priv->regs; + unsigned long flags; + u32 tempval; + + /* Lock it down */ + spin_lock_irqsave(&priv->lock, flags); + + /* Tell the kernel the link is down */ + priv->mii_info->link = 0; + adjust_link(dev); + + /* Mask all interrupts */ + gfar_write(®s->imask, IMASK_INIT_CLEAR); + + /* Clear all interrupts */ + gfar_write(®s->ievent, IEVENT_INIT_CLEAR); + + /* Stop the DMA, and wait for it to stop */ + tempval = gfar_read(&priv->regs->dmactrl); + if ((tempval & (DMACTRL_GRS | DMACTRL_GTS)) + != (DMACTRL_GRS | DMACTRL_GTS)) { + tempval |= (DMACTRL_GRS | DMACTRL_GTS); + gfar_write(&priv->regs->dmactrl, tempval); + + while (!(gfar_read(&priv->regs->ievent) & + (IEVENT_GRSC | IEVENT_GTSC))) + cpu_relax(); + } + + /* Disable Rx and Tx */ + tempval = gfar_read(®s->maccfg1); + tempval &= ~(MACCFG1_RX_EN | MACCFG1_TX_EN); + gfar_write(®s->maccfg1, tempval); + + if (priv->einfo->board_flags & FSL_GIANFAR_BRD_HAS_PHY_INTR) { + /* Clear any pending interrupts */ + mii_clear_phy_interrupt(priv->mii_info); + + /* Disable PHY Interrupts */ + mii_configure_phy_interrupt(priv->mii_info, + MII_INTERRUPT_DISABLED); + } + + spin_unlock_irqrestore(&priv->lock, flags); + + /* Free the IRQs */ + if (priv->einfo->device_flags & FSL_GIANFAR_DEV_HAS_MULTI_INTR) { + free_irq(priv->interruptError, dev); + free_irq(priv->interruptTransmit, dev); + free_irq(priv->interruptReceive, dev); + } else { + free_irq(priv->interruptTransmit, dev); + } + + if (priv->einfo->board_flags & FSL_GIANFAR_BRD_HAS_PHY_INTR) { + free_irq(priv->einfo->interruptPHY, dev); + } else { + del_timer_sync(&priv->phy_info_timer); + } + + free_skb_resources(priv); + + dma_free_coherent(NULL, + sizeof(struct txbd8)*priv->tx_ring_size + + sizeof(struct rxbd8)*priv->rx_ring_size, + priv->tx_bd_base, + gfar_read(®s->tbase)); +} + +/* If there are any tx skbs or rx skbs still around, free them. + * Then free tx_skbuff and rx_skbuff */ +void free_skb_resources(struct gfar_private *priv) +{ + struct rxbd8 *rxbdp; + struct txbd8 *txbdp; + int i; + + /* Go through all the buffer descriptors and free their data buffers */ + txbdp = priv->tx_bd_base; + + for (i = 0; i < priv->tx_ring_size; i++) { + + if (priv->tx_skbuff[i]) { + dma_unmap_single(NULL, txbdp->bufPtr, + txbdp->length, + DMA_TO_DEVICE); + dev_kfree_skb_any(priv->tx_skbuff[i]); + priv->tx_skbuff[i] = NULL; + } + } + + kfree(priv->tx_skbuff); + + rxbdp = priv->rx_bd_base; + + /* rx_skbuff is not guaranteed to be allocated, so only + * free it and its contents if it is allocated */ + if(priv->rx_skbuff != NULL) { + for (i = 0; i < priv->rx_ring_size; i++) { + if (priv->rx_skbuff[i]) { + dma_unmap_single(NULL, rxbdp->bufPtr, + priv->rx_buffer_size + + RXBUF_ALIGNMENT, + DMA_FROM_DEVICE); + + dev_kfree_skb_any(priv->rx_skbuff[i]); + priv->rx_skbuff[i] = NULL; + } + + rxbdp->status = 0; + rxbdp->length = 0; + rxbdp->bufPtr = 0; + + rxbdp++; + } + + kfree(priv->rx_skbuff); + } +} + +/* Bring the controller up and running */ +int startup_gfar(struct net_device *dev) +{ + struct txbd8 *txbdp; + struct rxbd8 *rxbdp; + dma_addr_t addr; + unsigned long vaddr; + int i; + struct gfar_private *priv = netdev_priv(dev); + struct gfar *regs = priv->regs; + u32 tempval; + int err = 0; + + gfar_write(®s->imask, IMASK_INIT_CLEAR); + + /* Allocate memory for the buffer descriptors */ + vaddr = (unsigned long) dma_alloc_coherent(NULL, + sizeof (struct txbd8) * priv->tx_ring_size + + sizeof (struct rxbd8) * priv->rx_ring_size, + &addr, GFP_KERNEL); + + if (vaddr == 0) { + printk(KERN_ERR "%s: Could not allocate buffer descriptors!\n", + dev->name); + return -ENOMEM; + } + + priv->tx_bd_base = (struct txbd8 *) vaddr; + + /* enet DMA only understands physical addresses */ + gfar_write(®s->tbase, addr); + + /* Start the rx descriptor ring where the tx ring leaves off */ + addr = addr + sizeof (struct txbd8) * priv->tx_ring_size; + vaddr = vaddr + sizeof (struct txbd8) * priv->tx_ring_size; + priv->rx_bd_base = (struct rxbd8 *) vaddr; + gfar_write(®s->rbase, addr); + + /* Setup the skbuff rings */ + priv->tx_skbuff = + (struct sk_buff **) kmalloc(sizeof (struct sk_buff *) * + priv->tx_ring_size, GFP_KERNEL); + + if (priv->tx_skbuff == NULL) { + printk(KERN_ERR "%s: Could not allocate tx_skbuff\n", + dev->name); + err = -ENOMEM; + goto tx_skb_fail; + } + + for (i = 0; i < priv->tx_ring_size; i++) + priv->tx_skbuff[i] = NULL; + + priv->rx_skbuff = + (struct sk_buff **) kmalloc(sizeof (struct sk_buff *) * + priv->rx_ring_size, GFP_KERNEL); + + if (priv->rx_skbuff == NULL) { + printk(KERN_ERR "%s: Could not allocate rx_skbuff\n", + dev->name); + err = -ENOMEM; + goto rx_skb_fail; + } + + for (i = 0; i < priv->rx_ring_size; i++) + priv->rx_skbuff[i] = NULL; + + /* Initialize some variables in our dev structure */ + priv->dirty_tx = priv->cur_tx = priv->tx_bd_base; + priv->cur_rx = priv->rx_bd_base; + priv->skb_curtx = priv->skb_dirtytx = 0; + priv->skb_currx = 0; + + /* Initialize Transmit Descriptor Ring */ + txbdp = priv->tx_bd_base; + for (i = 0; i < priv->tx_ring_size; i++) { + txbdp->status = 0; + txbdp->length = 0; + txbdp->bufPtr = 0; + txbdp++; + } + + /* Set the last descriptor in the ring to indicate wrap */ + txbdp--; + txbdp->status |= TXBD_WRAP; + + rxbdp = priv->rx_bd_base; + for (i = 0; i < priv->rx_ring_size; i++) { + struct sk_buff *skb = NULL; + + rxbdp->status = 0; + + skb = gfar_new_skb(dev, rxbdp); + + priv->rx_skbuff[i] = skb; + + rxbdp++; + } + + /* Set the last descriptor in the ring to wrap */ + rxbdp--; + rxbdp->status |= RXBD_WRAP; + + /* If the device has multiple interrupts, register for + * them. Otherwise, only register for the one */ + if (priv->einfo->device_flags & FSL_GIANFAR_DEV_HAS_MULTI_INTR) { + /* Install our interrupt handlers for Error, + * Transmit, and Receive */ + if (request_irq(priv->interruptError, gfar_error, + 0, "enet_error", dev) < 0) { + printk(KERN_ERR "%s: Can't get IRQ %d\n", + dev->name, priv->interruptError); + + err = -1; + goto err_irq_fail; + } + + if (request_irq(priv->interruptTransmit, gfar_transmit, + 0, "enet_tx", dev) < 0) { + printk(KERN_ERR "%s: Can't get IRQ %d\n", + dev->name, priv->interruptTransmit); + + err = -1; + + goto tx_irq_fail; + } + + if (request_irq(priv->interruptReceive, gfar_receive, + 0, "enet_rx", dev) < 0) { + printk(KERN_ERR "%s: Can't get IRQ %d (receive0)\n", + dev->name, priv->interruptReceive); + + err = -1; + goto rx_irq_fail; + } + } else { + if (request_irq(priv->interruptTransmit, gfar_interrupt, + 0, "gfar_interrupt", dev) < 0) { + printk(KERN_ERR "%s: Can't get IRQ %d\n", + dev->name, priv->interruptError); + + err = -1; + goto err_irq_fail; + } + } + + /* Set up the PHY change work queue */ + INIT_WORK(&priv->tq, gfar_phy_change, dev); + + init_timer(&priv->phy_info_timer); + priv->phy_info_timer.function = &gfar_phy_startup_timer; + priv->phy_info_timer.data = (unsigned long) priv->mii_info; + mod_timer(&priv->phy_info_timer, jiffies + HZ); + + /* Configure the coalescing support */ + if (priv->txcoalescing) + gfar_write(®s->txic, + mk_ic_value(priv->txcount, priv->txtime)); + else + gfar_write(®s->txic, 0); + + if (priv->rxcoalescing) + gfar_write(®s->rxic, + mk_ic_value(priv->rxcount, priv->rxtime)); + else + gfar_write(®s->rxic, 0); + + init_waitqueue_head(&priv->rxcleanupq); + + /* Enable Rx and Tx in MACCFG1 */ + tempval = gfar_read(®s->maccfg1); + tempval |= (MACCFG1_RX_EN | MACCFG1_TX_EN); + gfar_write(®s->maccfg1, tempval); + + /* Initialize DMACTRL to have WWR and WOP */ + tempval = gfar_read(&priv->regs->dmactrl); + tempval |= DMACTRL_INIT_SETTINGS; + gfar_write(&priv->regs->dmactrl, tempval); + + /* Clear THLT, so that the DMA starts polling now */ + gfar_write(®s->tstat, TSTAT_CLEAR_THALT); + + /* Make sure we aren't stopped */ + tempval = gfar_read(&priv->regs->dmactrl); + tempval &= ~(DMACTRL_GRS | DMACTRL_GTS); + gfar_write(&priv->regs->dmactrl, tempval); + + /* Unmask the interrupts we look for */ + gfar_write(®s->imask, IMASK_DEFAULT); + + return 0; + +rx_irq_fail: + free_irq(priv->interruptTransmit, dev); +tx_irq_fail: + free_irq(priv->interruptError, dev); +err_irq_fail: +rx_skb_fail: + free_skb_resources(priv); +tx_skb_fail: + dma_free_coherent(NULL, + sizeof(struct txbd8)*priv->tx_ring_size + + sizeof(struct rxbd8)*priv->rx_ring_size, + priv->tx_bd_base, + gfar_read(®s->tbase)); + + if (priv->mii_info->phyinfo->close) + priv->mii_info->phyinfo->close(priv->mii_info); + + kfree(priv->mii_info); + + return err; +} + +/* Called when something needs to use the ethernet device */ +/* Returns 0 for success. */ +static int gfar_enet_open(struct net_device *dev) +{ + int err; + + /* Initialize a bunch of registers */ + init_registers(dev); + + gfar_set_mac_address(dev); + + err = init_phy(dev); + + if(err) + return err; + + err = startup_gfar(dev); + + netif_start_queue(dev); + + return err; +} + +/* This is called by the kernel when a frame is ready for transmission. */ +/* It is pointed to by the dev->hard_start_xmit function pointer */ +static int gfar_start_xmit(struct sk_buff *skb, struct net_device *dev) +{ + struct gfar_private *priv = netdev_priv(dev); + struct txbd8 *txbdp; + + /* Update transmit stats */ + priv->stats.tx_bytes += skb->len; + + /* Lock priv now */ + spin_lock_irq(&priv->lock); + + /* Point at the first free tx descriptor */ + txbdp = priv->cur_tx; + + /* Clear all but the WRAP status flags */ + txbdp->status &= TXBD_WRAP; + + /* Set buffer length and pointer */ + txbdp->length = skb->len; + txbdp->bufPtr = dma_map_single(NULL, skb->data, + skb->len, DMA_TO_DEVICE); + + /* Save the skb pointer so we can free it later */ + priv->tx_skbuff[priv->skb_curtx] = skb; + + /* Update the current skb pointer (wrapping if this was the last) */ + priv->skb_curtx = + (priv->skb_curtx + 1) & TX_RING_MOD_MASK(priv->tx_ring_size); + + /* Flag the BD as interrupt-causing */ + txbdp->status |= TXBD_INTERRUPT; + + /* Flag the BD as ready to go, last in frame, and */ + /* in need of CRC */ + txbdp->status |= (TXBD_READY | TXBD_LAST | TXBD_CRC); + + dev->trans_start = jiffies; + + /* If this was the last BD in the ring, the next one */ + /* is at the beginning of the ring */ + if (txbdp->status & TXBD_WRAP) + txbdp = priv->tx_bd_base; + else + txbdp++; + + /* If the next BD still needs to be cleaned up, then the bds + are full. We need to tell the kernel to stop sending us stuff. */ + if (txbdp == priv->dirty_tx) { + netif_stop_queue(dev); + + priv->stats.tx_fifo_errors++; + } + + /* Update the current txbd to the next one */ + priv->cur_tx = txbdp; + + /* Tell the DMA to go go go */ + gfar_write(&priv->regs->tstat, TSTAT_CLEAR_THALT); + + /* Unlock priv */ + spin_unlock_irq(&priv->lock); + + return 0; +} + +/* Stops the kernel queue, and halts the controller */ +static int gfar_close(struct net_device *dev) +{ + struct gfar_private *priv = netdev_priv(dev); + stop_gfar(dev); + + /* Shutdown the PHY */ + if (priv->mii_info->phyinfo->close) + priv->mii_info->phyinfo->close(priv->mii_info); + + kfree(priv->mii_info); + + netif_stop_queue(dev); + + return 0; +} + +/* returns a net_device_stats structure pointer */ +static struct net_device_stats * gfar_get_stats(struct net_device *dev) +{ + struct gfar_private *priv = netdev_priv(dev); + + return &(priv->stats); +} + +/* Changes the mac address if the controller is not running. */ +int gfar_set_mac_address(struct net_device *dev) +{ + struct gfar_private *priv = netdev_priv(dev); + int i; + char tmpbuf[MAC_ADDR_LEN]; + u32 tempval; + + /* Now copy it into the mac registers backwards, cuz */ + /* little endian is silly */ + for (i = 0; i < MAC_ADDR_LEN; i++) + tmpbuf[MAC_ADDR_LEN - 1 - i] = dev->dev_addr[i]; + + gfar_write(&priv->regs->macstnaddr1, *((u32 *) (tmpbuf))); + + tempval = *((u32 *) (tmpbuf + 4)); + + gfar_write(&priv->regs->macstnaddr2, tempval); + + return 0; +} + + +static int gfar_change_mtu(struct net_device *dev, int new_mtu) +{ + int tempsize, tempval; + struct gfar_private *priv = netdev_priv(dev); + int oldsize = priv->rx_buffer_size; + int frame_size = new_mtu + 18; + + if ((frame_size < 64) || (frame_size > JUMBO_FRAME_SIZE)) { + printk(KERN_ERR "%s: Invalid MTU setting\n", dev->name); + return -EINVAL; + } + + tempsize = + (frame_size & ~(INCREMENTAL_BUFFER_SIZE - 1)) + + INCREMENTAL_BUFFER_SIZE; + + /* Only stop and start the controller if it isn't already + * stopped */ + if ((oldsize != tempsize) && (dev->flags & IFF_UP)) + stop_gfar(dev); + + priv->rx_buffer_size = tempsize; + + dev->mtu = new_mtu; + + gfar_write(&priv->regs->mrblr, priv->rx_buffer_size); + gfar_write(&priv->regs->maxfrm, priv->rx_buffer_size); + + /* If the mtu is larger than the max size for standard + * ethernet frames (ie, a jumbo frame), then set maccfg2 + * to allow huge frames, and to check the length */ + tempval = gfar_read(&priv->regs->maccfg2); + + if (priv->rx_buffer_size > DEFAULT_RX_BUFFER_SIZE) + tempval |= (MACCFG2_HUGEFRAME | MACCFG2_LENGTHCHECK); + else + tempval &= ~(MACCFG2_HUGEFRAME | MACCFG2_LENGTHCHECK); + + gfar_write(&priv->regs->maccfg2, tempval); + + if ((oldsize != tempsize) && (dev->flags & IFF_UP)) + startup_gfar(dev); + + return 0; +} + +/* gfar_timeout gets called when a packet has not been + * transmitted after a set amount of time. + * For now, assume that clearing out all the structures, and + * starting over will fix the problem. */ +static void gfar_timeout(struct net_device *dev) +{ + struct gfar_private *priv = netdev_priv(dev); + + priv->stats.tx_errors++; + + if (dev->flags & IFF_UP) { + stop_gfar(dev); + startup_gfar(dev); + } + + netif_schedule(dev); +} + +/* Interrupt Handler for Transmit complete */ +static irqreturn_t gfar_transmit(int irq, void *dev_id, struct pt_regs *regs) +{ + struct net_device *dev = (struct net_device *) dev_id; + struct gfar_private *priv = netdev_priv(dev); + struct txbd8 *bdp; + + /* Clear IEVENT */ + gfar_write(&priv->regs->ievent, IEVENT_TX_MASK); + + /* Lock priv */ + spin_lock(&priv->lock); + bdp = priv->dirty_tx; + while ((bdp->status & TXBD_READY) == 0) { + /* If dirty_tx and cur_tx are the same, then either the */ + /* ring is empty or full now (it could only be full in the beginning, */ + /* obviously). If it is empty, we are done. */ + if ((bdp == priv->cur_tx) && (netif_queue_stopped(dev) == 0)) + break; + + priv->stats.tx_packets++; + + /* Deferred means some collisions occurred during transmit, */ + /* but we eventually sent the packet. */ + if (bdp->status & TXBD_DEF) + priv->stats.collisions++; + + /* Free the sk buffer associated with this TxBD */ + dev_kfree_skb_irq(priv->tx_skbuff[priv->skb_dirtytx]); + priv->tx_skbuff[priv->skb_dirtytx] = NULL; + priv->skb_dirtytx = + (priv->skb_dirtytx + + 1) & TX_RING_MOD_MASK(priv->tx_ring_size); + + /* update bdp to point at next bd in the ring (wrapping if necessary) */ + if (bdp->status & TXBD_WRAP) + bdp = priv->tx_bd_base; + else + bdp++; + + /* Move dirty_tx to be the next bd */ + priv->dirty_tx = bdp; + + /* We freed a buffer, so now we can restart transmission */ + if (netif_queue_stopped(dev)) + netif_wake_queue(dev); + } /* while ((bdp->status & TXBD_READY) == 0) */ + + /* If we are coalescing the interrupts, reset the timer */ + /* Otherwise, clear it */ + if (priv->txcoalescing) + gfar_write(&priv->regs->txic, + mk_ic_value(priv->txcount, priv->txtime)); + else + gfar_write(&priv->regs->txic, 0); + + spin_unlock(&priv->lock); + + return IRQ_HANDLED; +} + +struct sk_buff * gfar_new_skb(struct net_device *dev, struct rxbd8 *bdp) +{ + struct gfar_private *priv = netdev_priv(dev); + struct sk_buff *skb = NULL; + unsigned int timeout = SKB_ALLOC_TIMEOUT; + + /* We have to allocate the skb, so keep trying till we succeed */ + while ((!skb) && timeout--) + skb = dev_alloc_skb(priv->rx_buffer_size + RXBUF_ALIGNMENT); + + if (skb == NULL) + return NULL; + + /* We need the data buffer to be aligned properly. We will reserve + * as many bytes as needed to align the data properly + */ + skb_reserve(skb, + RXBUF_ALIGNMENT - + (((unsigned) skb->data) & (RXBUF_ALIGNMENT - 1))); + + skb->dev = dev; + + bdp->bufPtr = dma_map_single(NULL, skb->data, + priv->rx_buffer_size + RXBUF_ALIGNMENT, + DMA_FROM_DEVICE); + + bdp->length = 0; + + /* Mark the buffer empty */ + bdp->status |= (RXBD_EMPTY | RXBD_INTERRUPT); + + return skb; +} + +static inline void count_errors(unsigned short status, struct gfar_private *priv) +{ + struct net_device_stats *stats = &priv->stats; + struct gfar_extra_stats *estats = &priv->extra_stats; + + /* If the packet was truncated, none of the other errors + * matter */ + if (status & RXBD_TRUNCATED) { + stats->rx_length_errors++; + + estats->rx_trunc++; + + return; + } + /* Count the errors, if there were any */ + if (status & (RXBD_LARGE | RXBD_SHORT)) { + stats->rx_length_errors++; + + if (status & RXBD_LARGE) + estats->rx_large++; + else + estats->rx_short++; + } + if (status & RXBD_NONOCTET) { + stats->rx_frame_errors++; + estats->rx_nonoctet++; + } + if (status & RXBD_CRCERR) { + estats->rx_crcerr++; + stats->rx_crc_errors++; + } + if (status & RXBD_OVERRUN) { + estats->rx_overrun++; + stats->rx_crc_errors++; + } +} + +irqreturn_t gfar_receive(int irq, void *dev_id, struct pt_regs *regs) +{ + struct net_device *dev = (struct net_device *) dev_id; + struct gfar_private *priv = netdev_priv(dev); + +#ifdef CONFIG_GFAR_NAPI + u32 tempval; +#endif + + /* Clear IEVENT, so rx interrupt isn't called again + * because of this interrupt */ + gfar_write(&priv->regs->ievent, IEVENT_RX_MASK); + + /* support NAPI */ +#ifdef CONFIG_GFAR_NAPI + if (netif_rx_schedule_prep(dev)) { + tempval = gfar_read(&priv->regs->imask); + tempval &= IMASK_RX_DISABLED; + gfar_write(&priv->regs->imask, tempval); + + __netif_rx_schedule(dev); + } else { +#ifdef VERBOSE_GFAR_ERRORS + printk(KERN_DEBUG "%s: receive called twice (%x)[%x]\n", + dev->name, gfar_read(&priv->regs->ievent), + gfar_read(&priv->regs->imask)); +#endif + } +#else + + spin_lock(&priv->lock); + gfar_clean_rx_ring(dev, priv->rx_ring_size); + + /* If we are coalescing interrupts, update the timer */ + /* Otherwise, clear it */ + if (priv->rxcoalescing) + gfar_write(&priv->regs->rxic, + mk_ic_value(priv->rxcount, priv->rxtime)); + else + gfar_write(&priv->regs->rxic, 0); + + /* Just in case we need to wake the ring param changer */ + priv->rxclean = 1; + + spin_unlock(&priv->lock); +#endif + + return IRQ_HANDLED; +} + + +/* gfar_process_frame() -- handle one incoming packet if skb + * isn't NULL. */ +static int gfar_process_frame(struct net_device *dev, struct sk_buff *skb, + int length) +{ + struct gfar_private *priv = netdev_priv(dev); + + if (skb == NULL) { +#ifdef BRIEF_GFAR_ERRORS + printk(KERN_WARNING "%s: Missing skb!!.\n", + dev->name); +#endif + priv->stats.rx_dropped++; + priv->extra_stats.rx_skbmissing++; + } else { + /* Prep the skb for the packet */ + skb_put(skb, length); + + /* Tell the skb what kind of packet this is */ + skb->protocol = eth_type_trans(skb, dev); + + /* Send the packet up the stack */ + if (RECEIVE(skb) == NET_RX_DROP) { + priv->extra_stats.kernel_dropped++; + } + } + + return 0; +} + +/* gfar_clean_rx_ring() -- Processes each frame in the rx ring + * until the budget/quota has been reached. Returns the number + * of frames handled + */ +static int gfar_clean_rx_ring(struct net_device *dev, int rx_work_limit) +{ + struct rxbd8 *bdp; + struct sk_buff *skb; + u16 pkt_len; + int howmany = 0; + struct gfar_private *priv = netdev_priv(dev); + + /* Get the first full descriptor */ + bdp = priv->cur_rx; + + while (!((bdp->status & RXBD_EMPTY) || (--rx_work_limit < 0))) { + skb = priv->rx_skbuff[priv->skb_currx]; + + if (!(bdp->status & + (RXBD_LARGE | RXBD_SHORT | RXBD_NONOCTET + | RXBD_CRCERR | RXBD_OVERRUN | RXBD_TRUNCATED))) { + /* Increment the number of packets */ + priv->stats.rx_packets++; + howmany++; + + /* Remove the FCS from the packet length */ + pkt_len = bdp->length - 4; + + gfar_process_frame(dev, skb, pkt_len); + + priv->stats.rx_bytes += pkt_len; + } else { + count_errors(bdp->status, priv); + + if (skb) + dev_kfree_skb_any(skb); + + priv->rx_skbuff[priv->skb_currx] = NULL; + } + + dev->last_rx = jiffies; + + /* Clear the status flags for this buffer */ + bdp->status &= ~RXBD_STATS; + + /* Add another skb for the future */ + skb = gfar_new_skb(dev, bdp); + priv->rx_skbuff[priv->skb_currx] = skb; + + /* Update to the next pointer */ + if (bdp->status & RXBD_WRAP) + bdp = priv->rx_bd_base; + else + bdp++; + + /* update to point at the next skb */ + priv->skb_currx = + (priv->skb_currx + + 1) & RX_RING_MOD_MASK(priv->rx_ring_size); + + } + + /* Update the current rxbd pointer to be the next one */ + priv->cur_rx = bdp; + + /* If no packets have arrived since the + * last one we processed, clear the IEVENT RX and + * BSY bits so that another interrupt won't be + * generated when we set IMASK */ + if (bdp->status & RXBD_EMPTY) + gfar_write(&priv->regs->ievent, IEVENT_RX_MASK); + + return howmany; +} + +#ifdef CONFIG_GFAR_NAPI +static int gfar_poll(struct net_device *dev, int *budget) +{ + int howmany; + struct gfar_private *priv = netdev_priv(dev); + int rx_work_limit = *budget; + + if (rx_work_limit > dev->quota) + rx_work_limit = dev->quota; + + howmany = gfar_clean_rx_ring(dev, rx_work_limit); + + dev->quota -= howmany; + rx_work_limit -= howmany; + *budget -= howmany; + + if (rx_work_limit >= 0) { + netif_rx_complete(dev); + + /* Clear the halt bit in RSTAT */ + gfar_write(&priv->regs->rstat, RSTAT_CLEAR_RHALT); + + gfar_write(&priv->regs->imask, IMASK_DEFAULT); + + /* If we are coalescing interrupts, update the timer */ + /* Otherwise, clear it */ + if (priv->rxcoalescing) + gfar_write(&priv->regs->rxic, + mk_ic_value(priv->rxcount, priv->rxtime)); + else + gfar_write(&priv->regs->rxic, 0); + + /* Signal to the ring size changer that it's safe to go */ + priv->rxclean = 1; + } + + return (rx_work_limit < 0) ? 1 : 0; +} +#endif + +/* The interrupt handler for devices with one interrupt */ +static irqreturn_t gfar_interrupt(int irq, void *dev_id, struct pt_regs *regs) +{ + struct net_device *dev = dev_id; + struct gfar_private *priv = netdev_priv(dev); + + /* Save ievent for future reference */ + u32 events = gfar_read(&priv->regs->ievent); + + /* Clear IEVENT */ + gfar_write(&priv->regs->ievent, events); + + /* Check for reception */ + if ((events & IEVENT_RXF0) || (events & IEVENT_RXB0)) + gfar_receive(irq, dev_id, regs); + + /* Check for transmit completion */ + if ((events & IEVENT_TXF) || (events & IEVENT_TXB)) + gfar_transmit(irq, dev_id, regs); + + /* Update error statistics */ + if (events & IEVENT_TXE) { + priv->stats.tx_errors++; + + if (events & IEVENT_LC) + priv->stats.tx_window_errors++; + if (events & IEVENT_CRL) + priv->stats.tx_aborted_errors++; + if (events & IEVENT_XFUN) { +#ifdef VERBOSE_GFAR_ERRORS + printk(KERN_WARNING "%s: tx underrun. dropped packet\n", + dev->name); +#endif + priv->stats.tx_dropped++; + priv->extra_stats.tx_underrun++; + + /* Reactivate the Tx Queues */ + gfar_write(&priv->regs->tstat, TSTAT_CLEAR_THALT); + } + } + if (events & IEVENT_BSY) { + priv->stats.rx_errors++; + priv->extra_stats.rx_bsy++; + + gfar_receive(irq, dev_id, regs); + +#ifndef CONFIG_GFAR_NAPI + /* Clear the halt bit in RSTAT */ + gfar_write(&priv->regs->rstat, RSTAT_CLEAR_RHALT); +#endif + +#ifdef VERBOSE_GFAR_ERRORS + printk(KERN_DEBUG "%s: busy error (rhalt: %x)\n", dev->name, + gfar_read(&priv->regs->rstat)); +#endif + } + if (events & IEVENT_BABR) { + priv->stats.rx_errors++; + priv->extra_stats.rx_babr++; + +#ifdef VERBOSE_GFAR_ERRORS + printk(KERN_DEBUG "%s: babbling error\n", dev->name); +#endif + } + if (events & IEVENT_EBERR) { + priv->extra_stats.eberr++; +#ifdef VERBOSE_GFAR_ERRORS + printk(KERN_DEBUG "%s: EBERR\n", dev->name); +#endif + } + if (events & IEVENT_RXC) { +#ifdef VERBOSE_GFAR_ERRORS + printk(KERN_DEBUG "%s: control frame\n", dev->name); +#endif + } + + if (events & IEVENT_BABT) { + priv->extra_stats.tx_babt++; +#ifdef VERBOSE_GFAR_ERRORS + printk(KERN_DEBUG "%s: babt error\n", dev->name); +#endif + } + + return IRQ_HANDLED; +} + +static irqreturn_t phy_interrupt(int irq, void *dev_id, struct pt_regs *regs) +{ + struct net_device *dev = (struct net_device *) dev_id; + struct gfar_private *priv = netdev_priv(dev); + + /* Clear the interrupt */ + mii_clear_phy_interrupt(priv->mii_info); + + /* Disable PHY interrupts */ + mii_configure_phy_interrupt(priv->mii_info, + MII_INTERRUPT_DISABLED); + + /* Schedule the phy change */ + schedule_work(&priv->tq); + + return IRQ_HANDLED; +} + +/* Scheduled by the phy_interrupt/timer to handle PHY changes */ +static void gfar_phy_change(void *data) +{ + struct net_device *dev = (struct net_device *) data; + struct gfar_private *priv = netdev_priv(dev); + int result = 0; + + /* Delay to give the PHY a chance to change the + * register state */ + msleep(1); + + /* Update the link, speed, duplex */ + result = priv->mii_info->phyinfo->read_status(priv->mii_info); + + /* Adjust the known status as long as the link + * isn't still coming up */ + if((0 == result) || (priv->mii_info->link == 0)) + adjust_link(dev); + + /* Reenable interrupts, if needed */ + if (priv->einfo->board_flags & FSL_GIANFAR_BRD_HAS_PHY_INTR) + mii_configure_phy_interrupt(priv->mii_info, + MII_INTERRUPT_ENABLED); +} + +/* Called every so often on systems that don't interrupt + * the core for PHY changes */ +static void gfar_phy_timer(unsigned long data) +{ + struct net_device *dev = (struct net_device *) data; + struct gfar_private *priv = netdev_priv(dev); + + schedule_work(&priv->tq); + + mod_timer(&priv->phy_info_timer, jiffies + + GFAR_PHY_CHANGE_TIME * HZ); +} + +/* Keep trying aneg for some time + * If, after GFAR_AN_TIMEOUT seconds, it has not + * finished, we switch to forced. + * Either way, once the process has completed, we either + * request the interrupt, or switch the timer over to + * using gfar_phy_timer to check status */ +static void gfar_phy_startup_timer(unsigned long data) +{ + int result; + static int secondary = GFAR_AN_TIMEOUT; + struct gfar_mii_info *mii_info = (struct gfar_mii_info *)data; + struct gfar_private *priv = netdev_priv(mii_info->dev); + + /* Configure the Auto-negotiation */ + result = mii_info->phyinfo->config_aneg(mii_info); + + /* If autonegotiation failed to start, and + * we haven't timed out, reset the timer, and return */ + if (result && secondary--) { + mod_timer(&priv->phy_info_timer, jiffies + HZ); + return; + } else if (result) { + /* Couldn't start autonegotiation. + * Try switching to forced */ + mii_info->autoneg = 0; + result = mii_info->phyinfo->config_aneg(mii_info); + + /* Forcing failed! Give up */ + if(result) { + printk(KERN_ERR "%s: Forcing failed!\n", + mii_info->dev->name); + return; + } + } + + /* Kill the timer so it can be restarted */ + del_timer_sync(&priv->phy_info_timer); + + /* Grab the PHY interrupt, if necessary/possible */ + if (priv->einfo->board_flags & FSL_GIANFAR_BRD_HAS_PHY_INTR) { + if (request_irq(priv->einfo->interruptPHY, + phy_interrupt, + SA_SHIRQ, + "phy_interrupt", + mii_info->dev) < 0) { + printk(KERN_ERR "%s: Can't get IRQ %d (PHY)\n", + mii_info->dev->name, + priv->einfo->interruptPHY); + } else { + mii_configure_phy_interrupt(priv->mii_info, + MII_INTERRUPT_ENABLED); + return; + } + } + + /* Start the timer again, this time in order to + * handle a change in status */ + init_timer(&priv->phy_info_timer); + priv->phy_info_timer.function = &gfar_phy_timer; + priv->phy_info_timer.data = (unsigned long) mii_info->dev; + mod_timer(&priv->phy_info_timer, jiffies + + GFAR_PHY_CHANGE_TIME * HZ); +} + +/* Called every time the controller might need to be made + * aware of new link state. The PHY code conveys this + * information through variables in the priv structure, and this + * function converts those variables into the appropriate + * register values, and can bring down the device if needed. + */ +static void adjust_link(struct net_device *dev) +{ + struct gfar_private *priv = netdev_priv(dev); + struct gfar *regs = priv->regs; + u32 tempval; + struct gfar_mii_info *mii_info = priv->mii_info; + + if (mii_info->link) { + /* Now we make sure that we can be in full duplex mode. + * If not, we operate in half-duplex mode. */ + if (mii_info->duplex != priv->oldduplex) { + if (!(mii_info->duplex)) { + tempval = gfar_read(®s->maccfg2); + tempval &= ~(MACCFG2_FULL_DUPLEX); + gfar_write(®s->maccfg2, tempval); + + printk(KERN_INFO "%s: Half Duplex\n", + dev->name); + } else { + tempval = gfar_read(®s->maccfg2); + tempval |= MACCFG2_FULL_DUPLEX; + gfar_write(®s->maccfg2, tempval); + + printk(KERN_INFO "%s: Full Duplex\n", + dev->name); + } + + priv->oldduplex = mii_info->duplex; + } + + if (mii_info->speed != priv->oldspeed) { + switch (mii_info->speed) { + case 1000: + tempval = gfar_read(®s->maccfg2); + tempval = + ((tempval & ~(MACCFG2_IF)) | MACCFG2_GMII); + gfar_write(®s->maccfg2, tempval); + break; + case 100: + case 10: + tempval = gfar_read(®s->maccfg2); + tempval = + ((tempval & ~(MACCFG2_IF)) | MACCFG2_MII); + gfar_write(®s->maccfg2, tempval); + break; + default: + printk(KERN_WARNING + "%s: Ack! Speed (%d) is not 10/100/1000!\n", + dev->name, mii_info->speed); + break; + } + + printk(KERN_INFO "%s: Speed %dBT\n", dev->name, + mii_info->speed); + + priv->oldspeed = mii_info->speed; + } + + if (!priv->oldlink) { + printk(KERN_INFO "%s: Link is up\n", dev->name); + priv->oldlink = 1; + netif_carrier_on(dev); + netif_schedule(dev); + } + } else { + if (priv->oldlink) { + printk(KERN_INFO "%s: Link is down\n", dev->name); + priv->oldlink = 0; + priv->oldspeed = 0; + priv->oldduplex = -1; + netif_carrier_off(dev); + } + } +} + + +/* Update the hash table based on the current list of multicast + * addresses we subscribe to. Also, change the promiscuity of + * the device based on the flags (this function is called + * whenever dev->flags is changed */ +static void gfar_set_multi(struct net_device *dev) +{ + struct dev_mc_list *mc_ptr; + struct gfar_private *priv = netdev_priv(dev); + struct gfar *regs = priv->regs; + u32 tempval; + + if(dev->flags & IFF_PROMISC) { + printk(KERN_INFO "%s: Entering promiscuous mode.\n", + dev->name); + /* Set RCTRL to PROM */ + tempval = gfar_read(®s->rctrl); + tempval |= RCTRL_PROM; + gfar_write(®s->rctrl, tempval); + } else { + /* Set RCTRL to not PROM */ + tempval = gfar_read(®s->rctrl); + tempval &= ~(RCTRL_PROM); + gfar_write(®s->rctrl, tempval); + } + + if(dev->flags & IFF_ALLMULTI) { + /* Set the hash to rx all multicast frames */ + gfar_write(®s->gaddr0, 0xffffffff); + gfar_write(®s->gaddr1, 0xffffffff); + gfar_write(®s->gaddr2, 0xffffffff); + gfar_write(®s->gaddr3, 0xffffffff); + gfar_write(®s->gaddr4, 0xffffffff); + gfar_write(®s->gaddr5, 0xffffffff); + gfar_write(®s->gaddr6, 0xffffffff); + gfar_write(®s->gaddr7, 0xffffffff); + } else { + /* zero out the hash */ + gfar_write(®s->gaddr0, 0x0); + gfar_write(®s->gaddr1, 0x0); + gfar_write(®s->gaddr2, 0x0); + gfar_write(®s->gaddr3, 0x0); + gfar_write(®s->gaddr4, 0x0); + gfar_write(®s->gaddr5, 0x0); + gfar_write(®s->gaddr6, 0x0); + gfar_write(®s->gaddr7, 0x0); + + if(dev->mc_count == 0) + return; + + /* Parse the list, and set the appropriate bits */ + for(mc_ptr = dev->mc_list; mc_ptr; mc_ptr = mc_ptr->next) { + gfar_set_hash_for_addr(dev, mc_ptr->dmi_addr); + } + } + + return; +} + +/* Set the appropriate hash bit for the given addr */ +/* The algorithm works like so: + * 1) Take the Destination Address (ie the multicast address), and + * do a CRC on it (little endian), and reverse the bits of the + * result. + * 2) Use the 8 most significant bits as a hash into a 256-entry + * table. The table is controlled through 8 32-bit registers: + * gaddr0-7. gaddr0's MSB is entry 0, and gaddr7's LSB is + * gaddr7. This means that the 3 most significant bits in the + * hash index which gaddr register to use, and the 5 other bits + * indicate which bit (assuming an IBM numbering scheme, which + * for PowerPC (tm) is usually the case) in the register holds + * the entry. */ +static void gfar_set_hash_for_addr(struct net_device *dev, u8 *addr) +{ + u32 tempval; + struct gfar_private *priv = netdev_priv(dev); + struct gfar *regs = priv->regs; + u32 *hash = ®s->gaddr0; + u32 result = ether_crc(MAC_ADDR_LEN, addr); + u8 whichreg = ((result >> 29) & 0x7); + u8 whichbit = ((result >> 24) & 0x1f); + u32 value = (1 << (31-whichbit)); + + tempval = gfar_read(&hash[whichreg]); + tempval |= value; + gfar_write(&hash[whichreg], tempval); + + return; +} + +/* GFAR error interrupt handler */ +static irqreturn_t gfar_error(int irq, void *dev_id, struct pt_regs *regs) +{ + struct net_device *dev = dev_id; + struct gfar_private *priv = netdev_priv(dev); + + /* Save ievent for future reference */ + u32 events = gfar_read(&priv->regs->ievent); + + /* Clear IEVENT */ + gfar_write(&priv->regs->ievent, IEVENT_ERR_MASK); + + /* Hmm... */ +#if defined (BRIEF_GFAR_ERRORS) || defined (VERBOSE_GFAR_ERRORS) + printk(KERN_DEBUG "%s: error interrupt (ievent=0x%08x imask=0x%08x)\n", + dev->name, events, gfar_read(&priv->regs->imask)); +#endif + + /* Update the error counters */ + if (events & IEVENT_TXE) { + priv->stats.tx_errors++; + + if (events & IEVENT_LC) + priv->stats.tx_window_errors++; + if (events & IEVENT_CRL) + priv->stats.tx_aborted_errors++; + if (events & IEVENT_XFUN) { +#ifdef VERBOSE_GFAR_ERRORS + printk(KERN_DEBUG "%s: underrun. packet dropped.\n", + dev->name); +#endif + priv->stats.tx_dropped++; + priv->extra_stats.tx_underrun++; + + /* Reactivate the Tx Queues */ + gfar_write(&priv->regs->tstat, TSTAT_CLEAR_THALT); + } +#ifdef VERBOSE_GFAR_ERRORS + printk(KERN_DEBUG "%s: Transmit Error\n", dev->name); +#endif + } + if (events & IEVENT_BSY) { + priv->stats.rx_errors++; + priv->extra_stats.rx_bsy++; + + gfar_receive(irq, dev_id, regs); + +#ifndef CONFIG_GFAR_NAPI + /* Clear the halt bit in RSTAT */ + gfar_write(&priv->regs->rstat, RSTAT_CLEAR_RHALT); +#endif + +#ifdef VERBOSE_GFAR_ERRORS + printk(KERN_DEBUG "%s: busy error (rhalt: %x)\n", dev->name, + gfar_read(&priv->regs->rstat)); +#endif + } + if (events & IEVENT_BABR) { + priv->stats.rx_errors++; + priv->extra_stats.rx_babr++; + +#ifdef VERBOSE_GFAR_ERRORS + printk(KERN_DEBUG "%s: babbling error\n", dev->name); +#endif + } + if (events & IEVENT_EBERR) { + priv->extra_stats.eberr++; +#ifdef VERBOSE_GFAR_ERRORS + printk(KERN_DEBUG "%s: EBERR\n", dev->name); +#endif + } + if (events & IEVENT_RXC) +#ifdef VERBOSE_GFAR_ERRORS + printk(KERN_DEBUG "%s: control frame\n", dev->name); +#endif + + if (events & IEVENT_BABT) { + priv->extra_stats.tx_babt++; +#ifdef VERBOSE_GFAR_ERRORS + printk(KERN_DEBUG "%s: babt error\n", dev->name); +#endif + } + return IRQ_HANDLED; +} + +/* Structure for a device driver */ +static struct device_driver gfar_driver = { + .name = "fsl-gianfar", + .bus = &platform_bus_type, + .probe = gfar_probe, + .remove = gfar_remove, +}; + +static int __init gfar_init(void) +{ + return driver_register(&gfar_driver); +} + +static void __exit gfar_exit(void) +{ + driver_unregister(&gfar_driver); +} + +module_init(gfar_init); +module_exit(gfar_exit); + |