diff options
Diffstat (limited to 'drivers/net/mipsnet.h')
-rw-r--r-- | drivers/net/mipsnet.h | 107 |
1 files changed, 107 insertions, 0 deletions
diff --git a/drivers/net/mipsnet.h b/drivers/net/mipsnet.h new file mode 100644 index 00000000000..026c732024c --- /dev/null +++ b/drivers/net/mipsnet.h @@ -0,0 +1,107 @@ +/* + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file "COPYING" in the main directory of this archive + * for more details. + */ +#ifndef __MIPSNET_H +#define __MIPSNET_H + +/* + * Id of this Net device, as seen by the core. + */ +#define MIPS_NET_DEV_ID ((uint64_t) \ + ((uint64_t)'M'<< 0)| \ + ((uint64_t)'I'<< 8)| \ + ((uint64_t)'P'<<16)| \ + ((uint64_t)'S'<<24)| \ + ((uint64_t)'N'<<32)| \ + ((uint64_t)'E'<<40)| \ + ((uint64_t)'T'<<48)| \ + ((uint64_t)'0'<<56)) + +/* + * Net status/control block as seen by sw in the core. + * (Why not use bit fields? can't be bothered with cross-platform struct + * packing.) + */ +typedef struct _net_control_block { + /// dev info for probing + /// reads as MIPSNET%d where %d is some form of version + uint64_t devId; /*0x00 */ + + /* + * read only busy flag. + * Set and cleared by the Net Device to indicate that an rx or a tx + * is in progress. + */ + uint32_t busy; /*0x08 */ + + /* + * Set by the Net Device. + * The device will set it once data has been received. + * The value is the number of bytes that should be read from + * rxDataBuffer. The value will decrease till 0 until all the data + * from rxDataBuffer has been read. + */ + uint32_t rxDataCount; /*0x0c */ +#define MIPSNET_MAX_RXTX_DATACOUNT (1<<16) + + /* + * Settable from the MIPS core, cleared by the Net Device. + * The core should set the number of bytes it wants to send, + * then it should write those bytes of data to txDataBuffer. + * The device will clear txDataCount has been processed (not necessarily sent). + */ + uint32_t txDataCount; /*0x10 */ + + /* + * Interrupt control + * + * Used to clear the interrupted generated by this dev. + * Write a 1 to clear the interrupt. (except bit31). + * + * Bit0 is set if it was a tx-done interrupt. + * Bit1 is set when new rx-data is available. + * Until this bit is cleared there will be no other RXs. + * + * Bit31 is used for testing, it clears after a read. + * Writing 1 to this bit will cause an interrupt to be generated. + * To clear the test interrupt, write 0 to this register. + */ + uint32_t interruptControl; /*0x14 */ +#define MIPSNET_INTCTL_TXDONE ((uint32_t)(1<< 0)) +#define MIPSNET_INTCTL_RXDONE ((uint32_t)(1<< 1)) +#define MIPSNET_INTCTL_TESTBIT ((uint32_t)(1<<31)) +#define MIPSNET_INTCTL_ALLSOURCES (MIPSNET_INTCTL_TXDONE|MIPSNET_INTCTL_RXDONE|MIPSNET_INTCTL_TESTBIT) + + /* + * Readonly core-specific interrupt info for the device to signal the core. + * The meaning of the contents of this field might change. + */ + /*###\todo: the whole memIntf interrupt scheme is messy: the device should have + * no control what so ever of what VPE/register set is being used. + * The MemIntf should only expose interrupt lines, and something in the + * config should be responsible for the line<->core/vpe bindings. + */ + uint32_t interruptInfo; /*0x18 */ + + /* + * This is where the received data is read out. + * There is more data to read until rxDataReady is 0. + * Only 1 byte at this regs offset is used. + */ + uint32_t rxDataBuffer; /*0x1c */ + + /* + * This is where the data to transmit is written. + * Data should be written for the amount specified in the txDataCount register. + * Only 1 byte at this regs offset is used. + */ + uint32_t txDataBuffer; /*0x20 */ +} MIPS_T_NetControl; + +#define MIPSNET_IO_EXTENT 0x40 /* being generous */ + +#define field_offset(field) ((int)&((MIPS_T_NetControl*)(0))->field) + +#endif /* __MIPSNET_H */ |