diff options
Diffstat (limited to 'drivers/net/ni52.c')
| -rw-r--r-- | drivers/net/ni52.c | 1346 |
1 files changed, 0 insertions, 1346 deletions
diff --git a/drivers/net/ni52.c b/drivers/net/ni52.c deleted file mode 100644 index d973fc6c6b8..00000000000 --- a/drivers/net/ni52.c +++ /dev/null @@ -1,1346 +0,0 @@ -/* - * net-3-driver for the NI5210 card (i82586 Ethernet chip) - * - * This is an extension to the Linux operating system, and is covered by the - * same GNU General Public License that covers that work. - * - * Alphacode 0.82 (96/09/29) for Linux 2.0.0 (or later) - * Copyrights (c) 1994,1995,1996 by M.Hipp (hippm@informatik.uni-tuebingen.de) - * [feel free to mail ....] - * - * when using as module: (no autoprobing!) - * run with e.g: - * insmod ni52.o io=0x360 irq=9 memstart=0xd0000 memend=0xd4000 - * - * CAN YOU PLEASE REPORT ME YOUR PERFORMANCE EXPERIENCES !!. - * - * If you find a bug, please report me: - * The kernel panic output and any kmsg from the ni52 driver - * the ni5210-driver-version and the linux-kernel version - * how many shared memory (memsize) on the netcard, - * bootprom: yes/no, base_addr, mem_start - * maybe the ni5210-card revision and the i82586 version - * - * autoprobe for: base_addr: 0x300,0x280,0x360,0x320,0x340 - * mem_start: 0xd0000,0xd2000,0xc8000,0xca000,0xd4000,0xd6000, - * 0xd8000,0xcc000,0xce000,0xda000,0xdc000 - * - * sources: - * skeleton.c from Donald Becker - * - * I have also done a look in the following sources: (mail me if you need them) - * crynwr-packet-driver by Russ Nelson - * Garret A. Wollman's (fourth) i82586-driver for BSD - * (before getting an i82596 (yes 596 not 586) manual, the existing drivers - * helped me a lot to understand this tricky chip.) - * - * Known Problems: - * The internal sysbus seems to be slow. So we often lose packets because of - * overruns while receiving from a fast remote host. - * This can slow down TCP connections. Maybe the newer ni5210 cards are - * better. My experience is, that if a machine sends with more than about - * 500-600K/s the fifo/sysbus overflows. - * - * IMPORTANT NOTE: - * On fast networks, it's a (very) good idea to have 16K shared memory. With - * 8K, we can store only 4 receive frames, so it can (easily) happen that a - * remote machine 'overruns' our system. - * - * Known i82586/card problems (I'm sure, there are many more!): - * Running the NOP-mode, the i82586 sometimes seems to forget to report - * every xmit-interrupt until we restart the CU. - * Another MAJOR bug is, that the RU sometimes seems to ignore the EL-Bit - * in the RBD-Struct which indicates an end of the RBD queue. - * Instead, the RU fetches another (randomly selected and - * usually used) RBD and begins to fill it. (Maybe, this happens only if - * the last buffer from the previous RFD fits exact into the queue and - * the next RFD can't fetch an initial RBD. Anyone knows more? ) - * - * results from ftp performance tests with Linux 1.2.5 - * send and receive about 350-400 KByte/s (peak up to 460 kbytes/s) - * sending in NOP-mode: peak performance up to 530K/s (but better don't - * run this mode) - */ - -/* - * 29.Sept.96: virt_to_bus changes for new memory scheme - * 19.Feb.96: more Mcast changes, module support (MH) - * - * 18.Nov.95: Mcast changes (AC). - * - * 23.April.95: fixed(?) receiving problems by configuring a RFD more - * than the number of RBD's. Can maybe cause other problems. - * 18.April.95: Added MODULE support (MH) - * 17.April.95: MC related changes in init586() and set_multicast_list(). - * removed use of 'jiffies' in init586() (MH) - * - * 19.Sep.94: Added Multicast support (not tested yet) (MH) - * - * 18.Sep.94: Workaround for 'EL-Bug'. Removed flexible RBD-handling. - * Now, every RFD has exact one RBD. (MH) - * - * 14.Sep.94: added promiscuous mode, a few cleanups (MH) - * - * 19.Aug.94: changed request_irq() parameter (MH) - * - * 20.July.94: removed cleanup bugs, removed a 16K-mem-probe-bug (MH) - * - * 19.July.94: lotsa cleanups .. (MH) - * - * 17.July.94: some patches ... verified to run with 1.1.29 (MH) - * - * 4.July.94: patches for Linux 1.1.24 (MH) - * - * 26.March.94: patches for Linux 1.0 and iomem-auto-probe (MH) - * - * 30.Sep.93: Added nop-chain .. driver now runs with only one Xmit-Buff, - * too (MH) - * - * < 30.Sep.93: first versions - */ - -static int debuglevel; /* debug-printk 0: off 1: a few 2: more */ -static int automatic_resume; /* experimental .. better should be zero */ -static int rfdadd; /* rfdadd=1 may be better for 8K MEM cards */ -static int fifo = 0x8; /* don't change */ - -#include <linux/module.h> -#include <linux/kernel.h> -#include <linux/string.h> -#include <linux/errno.h> -#include <linux/ioport.h> -#include <linux/interrupt.h> -#include <linux/delay.h> -#include <linux/init.h> -#include <linux/bitops.h> -#include <asm/io.h> - -#include <linux/netdevice.h> -#include <linux/etherdevice.h> -#include <linux/skbuff.h> - -#include "ni52.h" - -#define DRV_NAME "ni52" - -#define DEBUG /* debug on */ -#define SYSBUSVAL 1 /* 8 Bit */ - -#define ni_attn586() { outb(0, dev->base_addr + NI52_ATTENTION); } -#define ni_reset586() { outb(0, dev->base_addr + NI52_RESET); } -#define ni_disint() { outb(0, dev->base_addr + NI52_INTDIS); } -#define ni_enaint() { outb(0, dev->base_addr + NI52_INTENA); } - -#define make32(ptr16) ((void __iomem *)(p->memtop + (short) (ptr16))) -#define make24(ptr32) ((char __iomem *)(ptr32)) - p->base -#define make16(ptr32) ((unsigned short) ((char __iomem *)(ptr32)\ - - p->memtop)) - -/******************* how to calculate the buffers ***************************** - - * IMPORTANT NOTE: if you configure only one NUM_XMIT_BUFFS, the driver works - * --------------- in a different (more stable?) mode. Only in this mode it's - * possible to configure the driver with 'NO_NOPCOMMANDS' - -sizeof(scp)=12; sizeof(scb)=16; sizeof(iscp)=8; -sizeof(scp)+sizeof(iscp)+sizeof(scb) = 36 = INIT -sizeof(rfd) = 24; sizeof(rbd) = 12; -sizeof(tbd) = 8; sizeof(transmit_cmd) = 16; -sizeof(nop_cmd) = 8; - - * if you don't know the driver, better do not change these values: */ - -#define RECV_BUFF_SIZE 1524 /* slightly oversized */ -#define XMIT_BUFF_SIZE 1524 /* slightly oversized */ -#define NUM_XMIT_BUFFS 1 /* config for both, 8K and 16K shmem */ -#define NUM_RECV_BUFFS_8 4 /* config for 8K shared mem */ -#define NUM_RECV_BUFFS_16 9 /* config for 16K shared mem */ -#define NO_NOPCOMMANDS /* only possible with NUM_XMIT_BUFFS=1 */ - -/**************************************************************************/ - - -#define NI52_TOTAL_SIZE 16 -#define NI52_ADDR0 0x02 -#define NI52_ADDR1 0x07 -#define NI52_ADDR2 0x01 - -static int ni52_probe1(struct net_device *dev, int ioaddr); -static irqreturn_t ni52_interrupt(int irq, void *dev_id); -static int ni52_open(struct net_device *dev); -static int ni52_close(struct net_device *dev); -static netdev_tx_t ni52_send_packet(struct sk_buff *, struct net_device *); -static struct net_device_stats *ni52_get_stats(struct net_device *dev); -static void set_multicast_list(struct net_device *dev); -static void ni52_timeout(struct net_device *dev); - -/* helper-functions */ -static int init586(struct net_device *dev); -static int check586(struct net_device *dev, unsigned size); -static void alloc586(struct net_device *dev); -static void startrecv586(struct net_device *dev); -static void __iomem *alloc_rfa(struct net_device *dev, void __iomem *ptr); -static void ni52_rcv_int(struct net_device *dev); -static void ni52_xmt_int(struct net_device *dev); -static void ni52_rnr_int(struct net_device *dev); - -struct priv { - char __iomem *base; - char __iomem *mapped; - char __iomem *memtop; - spinlock_t spinlock; - int reset; - struct rfd_struct __iomem *rfd_last, *rfd_top, *rfd_first; - struct scp_struct __iomem *scp; - struct iscp_struct __iomem *iscp; - struct scb_struct __iomem *scb; - struct tbd_struct __iomem *xmit_buffs[NUM_XMIT_BUFFS]; -#if (NUM_XMIT_BUFFS == 1) - struct transmit_cmd_struct __iomem *xmit_cmds[2]; - struct nop_cmd_struct __iomem *nop_cmds[2]; -#else - struct transmit_cmd_struct __iomem *xmit_cmds[NUM_XMIT_BUFFS]; - struct nop_cmd_struct __iomem *nop_cmds[NUM_XMIT_BUFFS]; -#endif - int nop_point, num_recv_buffs; - char __iomem *xmit_cbuffs[NUM_XMIT_BUFFS]; - int xmit_count, xmit_last; -}; - -/* wait for command with timeout: */ -static void wait_for_scb_cmd(struct net_device *dev) -{ - struct priv *p = netdev_priv(dev); - int i; - for (i = 0; i < 16384; i++) { - if (readb(&p->scb->cmd_cuc) == 0) - break; - udelay(4); - if (i == 16383) { - printk(KERN_ERR "%s: scb_cmd timed out: %04x,%04x .. disabling i82586!!\n", - dev->name, readb(&p->scb->cmd_cuc), readb(&p->scb->cus)); - if (!p->reset) { - p->reset = 1; - ni_reset586(); - } - } - } -} - -static void wait_for_scb_cmd_ruc(struct net_device *dev) -{ - struct priv *p = netdev_priv(dev); - int i; - for (i = 0; i < 16384; i++) { - if (readb(&p->scb->cmd_ruc) == 0) - break; - udelay(4); - if (i == 16383) { - printk(KERN_ERR "%s: scb_cmd (ruc) timed out: %04x,%04x .. disabling i82586!!\n", - dev->name, readb(&p->scb->cmd_ruc), - readb(&p->scb->rus)); - if (!p->reset) { - p->reset = 1; - ni_reset586(); - } - } - } -} - -static void wait_for_stat_compl(void __iomem *p) -{ - struct nop_cmd_struct __iomem *addr = p; - int i; - for (i = 0; i < 32767; i++) { - if (readw(&((addr)->cmd_status)) & STAT_COMPL) - break; - udelay(32); - } -} - -/********************************************** - * close device - */ -static int ni52_close(struct net_device *dev) -{ - free_irq(dev->irq, dev); - ni_reset586(); /* the hard way to stop the receiver */ - netif_stop_queue(dev); - return 0; -} - -/********************************************** - * open device - */ -static int ni52_open(struct net_device *dev) -{ - int ret; - - ni_disint(); - alloc586(dev); - init586(dev); - startrecv586(dev); - ni_enaint(); - - ret = request_irq(dev->irq, ni52_interrupt, 0, dev->name, dev); - if (ret) { - ni_reset586(); - return ret; - } - netif_start_queue(dev); - return 0; /* most done by init */ -} - -static int check_iscp(struct net_device *dev, void __iomem *addr) -{ - struct iscp_struct __iomem *iscp = addr; - struct priv *p = netdev_priv(dev); - memset_io(iscp, 0, sizeof(struct iscp_struct)); - - writel(make24(iscp), &p->scp->iscp); - writeb(1, &iscp->busy); - - ni_reset586(); - ni_attn586(); - mdelay(32); /* wait a while... */ - /* i82586 clears 'busy' after successful init */ - if (readb(&iscp->busy)) - return 0; - return 1; -} - -/********************************************** - * Check to see if there's an 82586 out there. - */ -static int check586(struct net_device *dev, unsigned size) -{ - struct priv *p = netdev_priv(dev); - int i; - - p->mapped = ioremap(dev->mem_start, size); - if (!p->mapped) - return 0; - - p->base = p->mapped + size - 0x01000000; - p->memtop = p->mapped + size; - p->scp = (struct scp_struct __iomem *)(p->base + SCP_DEFAULT_ADDRESS); - p->scb = (struct scb_struct __iomem *) p->mapped; - p->iscp = (struct iscp_struct __iomem *)p->scp - 1; - memset_io(p->scp, 0, sizeof(struct scp_struct)); - for (i = 0; i < sizeof(struct scp_struct); i++) - /* memory was writeable? */ - if (readb((char __iomem *)p->scp + i)) - goto Enodev; - writeb(SYSBUSVAL, &p->scp->sysbus); /* 1 = 8Bit-Bus, 0 = 16 Bit */ - if (readb(&p->scp->sysbus) != SYSBUSVAL) - goto Enodev; - - if (!check_iscp(dev, p->mapped)) - goto Enodev; - if (!check_iscp(dev, p->iscp)) - goto Enodev; - return 1; -Enodev: - iounmap(p->mapped); - return 0; -} - -/****************************************************************** - * set iscp at the right place, called by ni52_probe1 and open586. - */ -static void alloc586(struct net_device *dev) -{ - struct priv *p = netdev_priv(dev); - - ni_reset586(); - mdelay(32); - - memset_io(p->iscp, 0, sizeof(struct iscp_struct)); - memset_io(p->scp , 0, sizeof(struct scp_struct)); - - writel(make24(p->iscp), &p->scp->iscp); - writeb(SYSBUSVAL, &p->scp->sysbus); - writew(make16(p->scb), &p->iscp->scb_offset); - - writeb(1, &p->iscp->busy); - ni_reset586(); - ni_attn586(); - - mdelay(32); - - if (readb(&p->iscp->busy)) - printk(KERN_ERR "%s: Init-Problems (alloc).\n", dev->name); - - p->reset = 0; - - memset_io(p->scb, 0, sizeof(struct scb_struct)); -} - -/* set: io,irq,memstart,memend or set it when calling insmod */ -static int irq = 9; -static int io = 0x300; -static long memstart; /* e.g 0xd0000 */ -static long memend; /* e.g 0xd4000 */ - -/********************************************** - * probe the ni5210-card - */ -struct net_device * __init ni52_probe(int unit) -{ - struct net_device *dev = alloc_etherdev(sizeof(struct priv)); - static const int ports[] = {0x300, 0x280, 0x360, 0x320, 0x340, 0}; - const int *port; - struct priv *p; - int err = 0; - - if (!dev) - return ERR_PTR(-ENOMEM); - - p = netdev_priv(dev); - - if (unit >= 0) { - sprintf(dev->name, "eth%d", unit); - netdev_boot_setup_check(dev); - io = dev->base_addr; - irq = dev->irq; - memstart = dev->mem_start; - memend = dev->mem_end; - } - - if (io > 0x1ff) { /* Check a single specified location. */ - err = ni52_probe1(dev, io); - } else if (io > 0) { /* Don't probe at all. */ - err = -ENXIO; - } else { - for (port = ports; *port && ni52_probe1(dev, *port) ; port++) - ; - if (*port) - goto got_it; -#ifdef FULL_IO_PROBE - for (io = 0x200; io < 0x400 && ni52_probe1(dev, io); io += 8) - ; - if (io < 0x400) - goto got_it; -#endif - err = -ENODEV; - } - if (err) - goto out; -got_it: - err = register_netdev(dev); - if (err) - goto out1; - return dev; -out1: - iounmap(p->mapped); - release_region(dev->base_addr, NI52_TOTAL_SIZE); -out: - free_netdev(dev); - return ERR_PTR(err); -} - -static const struct net_device_ops ni52_netdev_ops = { - .ndo_open = ni52_open, - .ndo_stop = ni52_close, - .ndo_get_stats = ni52_get_stats, - .ndo_tx_timeout = ni52_timeout, - .ndo_start_xmit = ni52_send_packet, - .ndo_set_multicast_list = set_multicast_list, - .ndo_change_mtu = eth_change_mtu, - .ndo_set_mac_address = eth_mac_addr, - .ndo_validate_addr = eth_validate_addr, -}; - -static int __init ni52_probe1(struct net_device *dev, int ioaddr) -{ - int i, size, retval; - struct priv *priv = netdev_priv(dev); - - dev->base_addr = ioaddr; - dev->irq = irq; - dev->mem_start = memstart; - dev->mem_end = memend; - - spin_lock_init(&priv->spinlock); - - if (!request_region(ioaddr, NI52_TOTAL_SIZE, DRV_NAME)) - return -EBUSY; - - if (!(inb(ioaddr+NI52_MAGIC1) == NI52_MAGICVAL1) || - !(inb(ioaddr+NI52_MAGIC2) == NI52_MAGICVAL2)) { - retval = -ENODEV; - goto out; - } - - for (i = 0; i < ETH_ALEN; i++) - dev->dev_addr[i] = inb(dev->base_addr+i); - - if (dev->dev_addr[0] != NI52_ADDR0 || dev->dev_addr[1] != NI52_ADDR1 || - dev->dev_addr[2] != NI52_ADDR2) { - retval = -ENODEV; - goto out; - } - - printk(KERN_INFO "%s: NI5210 found at %#3lx, ", - dev->name, dev->base_addr); - - /* - * check (or search) IO-Memory, 8K and 16K - */ -#ifdef MODULE - size = dev->mem_end - dev->mem_start; - if (size != 0x2000 && size != 0x4000) { - printk("\n"); - printk(KERN_ERR "%s: Invalid memory size %d. Allowed is 0x2000 or 0x4000 bytes.\n", dev->name, size); - retval = -ENODEV; - goto out; - } - if (!check586(dev, size)) { - printk(KERN_ERR "?memcheck, Can't find memory at 0x%lx with size %d!\n", dev->mem_start, size); - retval = -ENODEV; - goto out; - } -#else - if (dev->mem_start != 0) { - /* no auto-mem-probe */ - size = 0x4000; /* check for 16K mem */ - if (!check586(dev, size)) { - size = 0x2000; /* check for 8K mem */ - if (!check586(dev, size)) { - printk(KERN_ERR "?memprobe, Can't find memory at 0x%lx!\n", dev->mem_start); - retval = -ENODEV; - goto out; - } - } - } else { - static const unsigned long memaddrs[] = { - 0xc8000, 0xca000, 0xcc000, 0xce000, 0xd0000, 0xd2000, - 0xd4000, 0xd6000, 0xd8000, 0xda000, 0xdc000, 0 - }; - for (i = 0;; i++) { - if (!memaddrs[i]) { - printk(KERN_ERR "?memprobe, Can't find io-memory!\n"); - retval = -ENODEV; - goto out; - } - dev->mem_start = memaddrs[i]; - size = 0x2000; /* check for 8K mem */ - if (check586(dev, size)) - /* 8K-check */ - break; - size = 0x4000; /* check for 16K mem */ - if (check586(dev, size)) - /* 16K-check */ - break; - } - } - /* set mem_end showed by 'ifconfig' */ - dev->mem_end = dev->mem_start + size; -#endif - - alloc586(dev); - - /* set number of receive-buffs according to memsize */ - if (size == 0x2000) - priv->num_recv_buffs = NUM_RECV_BUFFS_8; - else - priv->num_recv_buffs = NUM_RECV_BUFFS_16; - - printk(KERN_DEBUG "Memaddr: 0x%lx, Memsize: %d, ", - dev->mem_start, size); - - if (dev->irq < 2) { - unsigned long irq_mask; - - irq_mask = probe_irq_on(); - ni_reset586(); - ni_attn586(); - - mdelay(20); - dev->irq = probe_irq_off(irq_mask); - if (!dev->irq) { - printk("?autoirq, Failed to detect IRQ line!\n"); - retval = -EAGAIN; - iounmap(priv->mapped); - goto out; - } - printk("IRQ %d (autodetected).\n", dev->irq); - } else { - if (dev->irq == 2) - dev->irq = 9; - printk("IRQ %d (assigned and not checked!).\n", dev->irq); - } - - dev->netdev_ops = &ni52_netdev_ops; - dev->watchdog_timeo = HZ/20; - - return 0; -out: - release_region(ioaddr, NI52_TOTAL_SIZE); - return retval; -} - -/********************************************** - * init the chip (ni52-interrupt should be disabled?!) - * needs a correct 'allocated' memory - */ - -static int init586(struct net_device *dev) -{ - void __iomem *ptr; - int i, result = 0; - struct priv *p = netdev_priv(dev); - struct configure_cmd_struct __iomem *cfg_cmd; - struct iasetup_cmd_struct __iomem *ias_cmd; - struct tdr_cmd_struct __iomem *tdr_cmd; - struct mcsetup_cmd_struct __iomem *mc_cmd; - struct netdev_hw_addr *ha; - int num_addrs = netdev_mc_count(dev); - - ptr = p->scb + 1; - - cfg_cmd = ptr; /* configure-command */ - writew(0, &cfg_cmd->cmd_status); - writew(CMD_CONFIGURE | CMD_LAST, &cfg_cmd->cmd_cmd); - writew(0xFFFF, &cfg_cmd->cmd_link); - - /* number of cfg bytes */ - writeb(0x0a, &cfg_cmd->byte_cnt); - /* fifo-limit (8=tx:32/rx:64) */ - writeb(fifo, &cfg_cmd->fifo); - /* hold or discard bad recv frames (bit 7) */ - writeb(0x40, &cfg_cmd->sav_bf); - /* addr_len |!src_insert |pre-len |loopback */ - writeb(0x2e, &cfg_cmd->adr_len); - writeb(0x00, &cfg_cmd->priority); - writeb(0x60, &cfg_cmd->ifs); - writeb(0x00, &cfg_cmd->time_low); - writeb(0xf2, &cfg_cmd->time_high); - writeb(0x00, &cfg_cmd->promisc); - if (dev->flags & IFF_ALLMULTI) { - int len = ((char __iomem *)p->iscp - (char __iomem *)ptr - 8) / 6; - if (num_addrs > len) { - printk(KERN_ERR "%s: switching to promisc. mode\n", - dev->name); - writeb(0x01, &cfg_cmd->promisc); - } - } - if (dev->flags & IFF_PROMISC) - writeb(0x01, &cfg_cmd->promisc); - writeb(0x00, &cfg_cmd->carr_coll); - writew(make16(cfg_cmd), &p->scb->cbl_offset); - writeb(0, &p->scb->cmd_ruc); - - writeb(CUC_START, &p->scb->cmd_cuc); /* cmd.-unit start */ - ni_attn586(); - - wait_for_stat_compl(cfg_cmd); - - if ((readw(&cfg_cmd->cmd_status) & (STAT_OK|STAT_COMPL)) != - (STAT_COMPL|STAT_OK)) { - printk(KERN_ERR "%s: configure command failed: %x\n", - dev->name, readw(&cfg_cmd->cmd_status)); - return 1; - } - - /* - * individual address setup - */ - - ias_cmd = ptr; - - writew(0, &ias_cmd->cmd_status); - writew(CMD_IASETUP | CMD_LAST, &ias_cmd->cmd_cmd); - writew(0xffff, &ias_cmd->cmd_link); - - memcpy_toio(&ias_cmd->iaddr, (char *)dev->dev_addr, ETH_ALEN); - - writew(make16(ias_cmd), &p->scb->cbl_offset); - - writeb(CUC_START, &p->scb->cmd_cuc); /* cmd.-unit start */ - ni_attn586(); - - wait_for_stat_compl(ias_cmd); - - if ((readw(&ias_cmd->cmd_status) & (STAT_OK|STAT_COMPL)) != - (STAT_OK|STAT_COMPL)) { - printk(KERN_ERR "%s (ni52): individual address setup command failed: %04x\n", dev->name, readw(&ias_cmd->cmd_status)); - return 1; - } - - /* - * TDR, wire check .. e.g. no resistor e.t.c - */ - - tdr_cmd = ptr; - - writew(0, &tdr_cmd->cmd_status); - writew(CMD_TDR | CMD_LAST, &tdr_cmd->cmd_cmd); - writew(0xffff, &tdr_cmd->cmd_link); - writew(0, &tdr_cmd->status); - - writew(make16(tdr_cmd), &p->scb->cbl_offset); - writeb(CUC_START, &p->scb->cmd_cuc); /* cmd.-unit start */ - ni_attn586(); - - wait_for_stat_compl(tdr_cmd); - - if (!(readw(&tdr_cmd->cmd_status) & STAT_COMPL)) - printk(KERN_ERR "%s: Problems while running the TDR.\n", - dev->name); - else { - udelay(16); - result = readw(&tdr_cmd->status); - writeb(readb(&p->scb->cus) & STAT_MASK, &p->scb->cmd_cuc); - ni_attn586(); /* ack the interrupts */ - - if (result & TDR_LNK_OK) - ; - else if (result & TDR_XCVR_PRB) - printk(KERN_ERR "%s: TDR: Transceiver problem. Check the cable(s)!\n", - dev->name); - else if (result & TDR_ET_OPN) - printk(KERN_ERR "%s: TDR: No correct termination %d clocks away.\n", - dev->name, result & TDR_TIMEMASK); - else if (result & TDR_ET_SRT) { - /* time == 0 -> strange :-) */ - if (result & TDR_TIMEMASK) - printk(KERN_ERR "%s: TDR: Detected a short circuit %d clocks away.\n", - dev->name, result & TDR_TIMEMASK); - } else - printk(KERN_ERR "%s: TDR: Unknown status %04x\n", - dev->name, result); - } - - /* - * Multicast setup - */ - if (num_addrs && !(dev->flags & IFF_PROMISC)) { - mc_cmd = ptr; - writew(0, &mc_cmd->cmd_status); - writew(CMD_MCSETUP | CMD_LAST, &mc_cmd->cmd_cmd); - writew(0xffff, &mc_cmd->cmd_link); - writew(num_addrs * 6, &mc_cmd->mc_cnt); - - i = 0; - netdev_for_each_mc_addr(ha, dev) - memcpy_toio(mc_cmd->mc_list[i++], ha->addr, 6); - - writew(make16(mc_cmd), &p->scb->cbl_offset); - writeb(CUC_START, &p->scb->cmd_cuc); - ni_attn586(); - - wait_for_stat_compl(mc_cmd); - - if ((readw(&mc_cmd->cmd_status) & (STAT_COMPL|STAT_OK)) - != (STAT_COMPL|STAT_OK)) - printk(KERN_ERR "%s: Can't apply multicast-address-list.\n", dev->name); - } - - /* - * alloc nop/xmit-cmds - */ -#if (NUM_XMIT_BUFFS == 1) - for (i = 0; i < 2; i++) { - p->nop_cmds[i] = ptr; - writew(CMD_NOP, &p->nop_cmds[i]->cmd_cmd); - writew(0, &p->nop_cmds[i]->cmd_status); - writew(make16(p->nop_cmds[i]), &p->nop_cmds[i]->cmd_link); - ptr = ptr + sizeof(struct nop_cmd_struct); - } -#else - for (i = 0; i < NUM_XMIT_BUFFS; i++) { - p->nop_cmds[i] = ptr; - writew(CMD_NOP, &p->nop_cmds[i]->cmd_cmd); - writew(0, &p->nop_cmds[i]->cmd_status); - writew(make16(p->nop_cmds[i]), &p->nop_cmds[i]->cmd_link); - ptr = ptr + sizeof(struct nop_cmd_struct); - } -#endif - - ptr = alloc_rfa(dev, ptr); /* init receive-frame-area */ - - /* - * alloc xmit-buffs / init xmit_cmds - */ - for (i = 0; i < NUM_XMIT_BUFFS; i++) { - /* Transmit cmd/buff 0 */ - p->xmit_cmds[i] = ptr; - ptr = ptr + sizeof(struct transmit_cmd_struct); - p->xmit_cbuffs[i] = ptr; /* char-buffs */ - ptr = ptr + XMIT_BUFF_SIZE; - p->xmit_buffs[i] = ptr; /* TBD */ - ptr = ptr + sizeof(struct tbd_struct); - if ((void __iomem *)ptr > (void __iomem *)p->iscp) { - printk(KERN_ERR "%s: not enough shared-mem for your configuration!\n", - dev->name); - return 1; - } - memset_io(p->xmit_cmds[i], 0, - sizeof(struct transmit_cmd_struct)); - memset_io(p->xmit_buffs[i], 0, - sizeof(struct tbd_struct)); - writew(make16(p->nop_cmds[(i+1)%NUM_XMIT_BUFFS]), - &p->xmit_cmds[i]->cmd_link); - writew(STAT_COMPL, &p->xmit_cmds[i]->cmd_status); - writew(CMD_XMIT|CMD_INT, &p->xmit_cmds[i]->cmd_cmd); - writew(make16(p->xmit_buffs[i]), &p->xmit_cmds[i]->tbd_offset); - writew(0xffff, &p->xmit_buffs[i]->next); - writel(make24(p->xmit_cbuffs[i]), &p->xmit_buffs[i]->buffer); - } - - p->xmit_count = 0; - p->xmit_last = 0; -#ifndef NO_NOPCOMMANDS - p->nop_point = 0; -#endif - - /* - * 'start transmitter' - */ -#ifndef NO_NOPCOMMANDS - writew(make16(p->nop_cmds[0]), &p->scb->cbl_offset); - writeb(CUC_START, &p->scb->cmd_cuc); - ni_attn586(); - wait_for_scb_cmd(dev); -#else - writew(make16(p->xmit_cmds[0]), &p->xmit_cmds[0]->cmd_link); - writew(CMD_XMIT | CMD_SUSPEND | CMD_INT, &p->xmit_cmds[0]->cmd_cmd); -#endif - - /* - * ack. interrupts - */ - writeb(readb(&p->scb->cus) & STAT_MASK, &p->scb->cmd_cuc); - ni_attn586(); - udelay(16); - - ni_enaint(); - - return 0; -} - -/****************************************************** - * This is a helper routine for ni52_rnr_int() and init586(). - * It sets up the Receive Frame Area (RFA). - */ - -static void __iomem *alloc_rfa(struct net_device *dev, void __iomem *ptr) -{ - struct rfd_struct __iomem *rfd = ptr; - struct rbd_struct __iomem *rbd; - int i; - struct priv *p = netdev_priv(dev); - - memset_io(rfd, 0, - sizeof(struct rfd_struct) * (p->num_recv_buffs + rfdadd)); - p->rfd_first = rfd; - - for (i = 0; i < (p->num_recv_buffs + rfdadd); i++) { - writew(make16(rfd + (i+1) % (p->num_recv_buffs+rfdadd)), - &rfd[i].next); - writew(0xffff, &rfd[i].rbd_offset); - } - /* RU suspend */ - writeb(RFD_SUSP, &rfd[p->num_recv_buffs-1+rfdadd].last); - - ptr = rfd + (p->num_recv_buffs + rfdadd); - - rbd = ptr; - ptr = rbd + p->num_recv_buffs; - - /* clr descriptors */ - memset_io(rbd, 0, sizeof(struct rbd_struct) * (p->num_recv_buffs)); - - for (i = 0; i < p->num_recv_buffs; i++) { - writew(make16(rbd + (i+1) % p->num_recv_buffs), &rbd[i].next); - writew(RECV_BUFF_SIZE, &rbd[i].size); - writel(make24(ptr), &rbd[i].buffer); - ptr = ptr + RECV_BUFF_SIZE; - } - p->rfd_top = p->rfd_first; - p->rfd_last = p->rfd_first + (p->num_recv_buffs - 1 + rfdadd); - - writew(make16(p->rfd_first), &p->scb->rfa_offset); - writew(make16(rbd), &p->rfd_first->rbd_offset); - - return ptr; -} - - -/************************************************** - * Interrupt Handler ... - */ - -static irqreturn_t ni52_interrupt(int irq, void *dev_id) -{ - struct net_device *dev = dev_id; - unsigned int stat; - int cnt = 0; - struct priv *p; - - p = netdev_priv(dev); - - if (debuglevel > 1) - printk("I"); - - spin_lock(&p->spinlock); - - wait_for_scb_cmd(dev); /* wait for last command */ - - while ((stat = readb(&p->scb->cus) & STAT_MASK)) { - writeb(stat, &p->scb->cmd_cuc); - ni_attn586(); - - if (stat & STAT_FR) /* received a frame */ - ni52_rcv_int(dev); - - if (stat & STAT_RNR) { /* RU went 'not ready' */ - printk("(R)"); - if (readb(&p->scb->rus) & RU_SUSPEND) { - /* special case: RU_SUSPEND */ - wait_for_scb_cmd(dev); - writeb(RUC_RESUME, &p->scb->cmd_ruc); - ni_attn586(); - wait_for_scb_cmd_ruc(dev); - } else { - printk(KERN_ERR "%s: Receiver-Unit went 'NOT READY': %04x/%02x.\n", - dev->name, stat, readb(&p->scb->rus)); - ni52_rnr_int(dev); - } - } - - /* Command with I-bit set complete */ - if (stat & STAT_CX) - ni52_xmt_int(dev); - -#ifndef NO_NOPCOMMANDS - if (stat & STAT_CNA) { /* CU went 'not ready' */ - if (netif_running(dev)) - printk(KERN_ERR "%s: oops! CU has left active state. stat: %04x/%02x.\n", - dev->name, stat, readb(&p->scb->cus)); - } -#endif - - if (debuglevel > 1) - printk("%d", cnt++); - - /* Wait for ack. (ni52_xmt_int can be faster than ack!!) */ - wait_for_scb_cmd(dev); - if (readb(&p->scb->cmd_cuc)) { /* timed out? */ - printk(KERN_ERR "%s: Acknowledge timed out.\n", - dev->name); - ni_disint(); - break; - } - } - spin_unlock(&p->spinlock); - - if (debuglevel > 1) - printk("i"); - return IRQ_HANDLED; -} - -/******************************************************* - * receive-interrupt - */ - -static void ni52_rcv_int(struct net_device *dev) -{ - int status, cnt = 0; - unsigned short totlen; - struct sk_buff *skb; - struct rbd_struct __iomem *rbd; - struct priv *p = netdev_priv(dev); - - if (debuglevel > 0) - printk("R"); - - for (; (status = readb(&p->rfd_top->stat_high)) & RFD_COMPL;) { - rbd = make32(readw(&p->rfd_top->rbd_offset)); - if (status & RFD_OK) { /* frame received without error? */ - totlen = readw(&rbd->status); - if (totlen & RBD_LAST) { - /* the first and the last buffer? */ - totlen &= RBD_MASK; /* length of this frame */ - writew(0x00, &rbd->status); - skb = (struct sk_buff *)dev_alloc_skb(totlen+2); - if (skb != NULL) { - skb_reserve(skb, 2); - skb_put(skb, totlen); - memcpy_fromio(skb->data, p->base + readl(&rbd->buffer), totlen); - skb->protocol = eth_type_trans(skb, dev); - netif_rx(skb); - dev->stats.rx_packets++; - dev->stats.rx_bytes += totlen; - } else - dev->stats.rx_dropped++; - } else { - int rstat; - /* free all RBD's until RBD_LAST is set */ - totlen = 0; - while (!((rstat = readw(&rbd->status)) & RBD_LAST)) { - totlen += rstat & RBD_MASK; - if (!rstat) { - printk(KERN_ERR "%s: Whoops .. no end mark in RBD list\n", dev->name); - break; - } - writew(0, &rbd->status); - rbd = make32(readw(&rbd->next)); - } - totlen += rstat & RBD_MASK; - writew(0, &rbd->status); - printk(KERN_ERR "%s: received oversized frame! length: %d\n", - dev->name, totlen); - dev->stats.rx_dropped++; - } - } else {/* frame !(ok), only with 'save-bad-frames' */ - printk(KERN_ERR "%s: oops! rfd-error-status: %04x\n", - dev->name, status); - dev->stats.rx_errors++; - } - writeb(0, &p->rfd_top->stat_high); - writeb(RFD_SUSP, &p->rfd_top->last); /* maybe exchange by RFD_LAST */ - writew(0xffff, &p->rfd_top->rbd_offset); - writeb(0, &p->rfd_last->last); /* delete RFD_SUSP */ - p->rfd_last = p->rfd_top; - p->rfd_top = make32(readw(&p->rfd_top->next)); /* step to next RFD */ - writew(make16(p->rfd_top), &p->scb->rfa_offset); - - if (debuglevel > 0) - printk("%d", cnt++); - } - - if (automatic_resume) { - wait_for_scb_cmd(dev); - writeb(RUC_RESUME, &p->scb->cmd_ruc); - ni_attn586(); - wait_for_scb_cmd_ruc(dev); - } - -#ifdef WAIT_4_BUSY - { - int i; - for (i = 0; i < 1024; i++) { - if (p->rfd_top->status) - break; - udelay(16); - if (i == 1023) - printk(KERN_ERR "%s: RU hasn't fetched next RFD (not busy/complete)\n", dev->name); - } - } -#endif - if (debuglevel > 0) - printk("r"); -} - -/********************************************************** - * handle 'Receiver went not ready'. - */ - -static void ni52_rnr_int(struct net_device *dev) -{ - struct priv *p = netdev_priv(dev); - - dev->stats.rx_errors++; - - wait_for_scb_cmd(dev); /* wait for the last cmd, WAIT_4_FULLSTAT?? */ - writeb(RUC_ABORT, &p->scb->cmd_ruc); /* usually the RU is in the 'no resource'-state .. abort it now. */ - ni_attn586(); - wait_for_scb_cmd_ruc(dev); /* wait for accept cmd. */ - - alloc_rfa(dev, p->rfd_first); - /* maybe add a check here, before restarting the RU */ - startrecv586(dev); /* restart RU */ - - printk(KERN_ERR "%s: Receive-Unit restarted. Status: %04x\n", - dev->name, readb(&p->scb->rus)); - -} - -/********************************************************** - * handle xmit - interrupt - */ - -static void ni52_xmt_int(struct net_device *dev) -{ - int status; - struct priv *p = netdev_priv(dev); - - if (debuglevel > 0) - printk("X"); - - status = readw(&p->xmit_cmds[p->xmit_last]->cmd_status); - if (!(status & STAT_COMPL)) - printk(KERN_ERR "%s: strange .. xmit-int without a 'COMPLETE'\n", dev->name); - - if (status & STAT_OK) { - dev->stats.tx_packets++; - dev->stats.collisions += (status & TCMD_MAXCOLLMASK); - } else { - dev->stats.tx_errors++; - if (status & TCMD_LATECOLL) { - printk(KERN_ERR "%s: late collision detected.\n", - dev->name); - dev->stats.collisions++; - } else if (status & TCMD_NOCARRIER) { - dev->stats.tx_carrier_errors++; - printk(KERN_ERR "%s: no carrier detected.\n", - dev->name); - } else if (status & TCMD_LOSTCTS) - printk(KERN_ERR "%s: loss of CTS detected.\n", - dev->name); - else if (status & TCMD_UNDERRUN) { - dev->stats.tx_fifo_errors++; - printk(KERN_ERR "%s: DMA underrun detected.\n", - dev->name); - } else if (status & TCMD_MAXCOLL) { - printk(KERN_ERR "%s: Max. collisions exceeded.\n", - dev->name); - dev->stats.collisions += 16; - } - } -#if (NUM_XMIT_BUFFS > 1) - if ((++p->xmit_last) == NUM_XMIT_BUFFS) - p->xmit_last = 0; -#endif - netif_wake_queue(dev); -} - -/*********************************************************** - * (re)start the receiver - */ - -static void startrecv586(struct net_device *dev) -{ - struct priv *p = netdev_priv(dev); - - wait_for_scb_cmd(dev); - wait_for_scb_cmd_ruc(dev); - writew(make16(p->rfd_first), &p->scb->rfa_offset); - writeb(RUC_START, &p->scb->cmd_ruc); - ni_attn586(); /* start cmd. */ - wait_for_scb_cmd_ruc(dev); - /* wait for accept cmd. (no timeout!!) */ -} - -static void ni52_timeout(struct net_device *dev) -{ - struct priv *p = netdev_priv(dev); -#ifndef NO_NOPCOMMANDS - if (readb(&p->scb->cus) & CU_ACTIVE) { /* COMMAND-UNIT active? */ - netif_wake_queue(dev); -#ifdef DEBUG - printk(KERN_ERR "%s: strange ... timeout with CU active?!?\n", - dev->name); - printk(KERN_ERR "%s: X0: %04x N0: %04x N1: %04x %d\n", - dev->name, (int)p->xmit_cmds[0]->cmd_status, - readw(&p->nop_cmds[0]->cmd_status), - readw(&p->nop_cmds[1]->cmd_status), - p->nop_point); -#endif - writeb(CUC_ABORT, &p->scb->cmd_cuc); - ni_attn586(); - wait_for_scb_cmd(dev); - writew(make16(p->nop_cmds[p->nop_point]), &p->scb->cbl_offset); - writeb(CUC_START, &p->scb->cmd_cuc); - ni_attn586(); - wait_for_scb_cmd(dev); - dev->trans_start = jiffies; /* prevent tx timeout */ - return 0; - } -#endif - { -#ifdef DEBUG - printk(KERN_ERR "%s: xmitter timed out, try to restart! stat: %02x\n", - dev->name, readb(&p->scb->cus)); - printk(KERN_ERR "%s: command-stats: %04x %04x\n", - dev->name, - readw(&p->xmit_cmds[0]->cmd_status), - readw(&p->xmit_cmds[1]->cmd_status)); - printk(KERN_ERR "%s: check, whether you set the right interrupt number!\n", - dev->name); -#endif - ni52_close(dev); - ni52_open(dev); - } - dev->trans_start = jiffies; /* prevent tx timeout */ -} - -/****************************************************** - * send frame - */ - -static netdev_tx_t ni52_send_packet(struct sk_buff *skb, - struct net_device *dev) -{ - int len, i; -#ifndef NO_NOPCOMMANDS - int next_nop; -#endif - struct priv *p = netdev_priv(dev); - - if (skb->len > XMIT_BUFF_SIZE) { - printk(KERN_ERR "%s: Sorry, max. framelength is %d bytes. The length of your frame is %d bytes.\n", dev->name, XMIT_BUFF_SIZE, skb->len); - return NETDEV_TX_OK; - } - - netif_stop_queue(dev); - - memcpy_toio(p->xmit_cbuffs[p->xmit_count], skb->data, skb->len); - len = skb->len; - if (len < ETH_ZLEN) { - len = ETH_ZLEN; - memset_io(p->xmit_cbuffs[p->xmit_count]+skb->len, 0, - len - skb->len); - } - -#if (NUM_XMIT_BUFFS == 1) -# ifdef NO_NOPCOMMANDS - -#ifdef DEBUG - if (readb(&p->scb->cus) & CU_ACTIVE) { - printk(KERN_ERR "%s: Hmmm .. CU is still running and we wanna send a new packet.\n", dev->name); - printk(KERN_ERR "%s: stat: %04x %04x\n", - dev->name, readb(&p->scb->cus), - readw(&p->xmit_cmds[0]->cmd_status)); - } -#endif - writew(TBD_LAST | len, &p->xmit_buffs[0]->size); - for (i = 0; i < 16; i++) { - writew(0, &p->xmit_cmds[0]->cmd_status); - wait_for_scb_cmd(dev); - if ((readb(&p->scb->cus) & CU_STATUS) == CU_SUSPEND) - writeb(CUC_RESUME, &p->scb->cmd_cuc); - else { - writew(make16(p->xmit_cmds[0]), &p->scb->cbl_offset); - writeb(CUC_START, &p->scb->cmd_cuc); - } - ni_attn586(); - if (!i) - dev_kfree_skb(skb); - wait_for_scb_cmd(dev); - /* test it, because CU sometimes doesn't start immediately */ - if (readb(&p->scb->cus) & CU_ACTIVE) - break; - if (readw(&p->xmit_cmds[0]->cmd_status)) - break; - if (i == 15) - printk(KERN_WARNING "%s: Can't start transmit-command.\n", dev->name); - } -# else - next_nop = (p->nop_point + 1) & 0x1; - writew(TBD_LAST | len, &p->xmit_buffs[0]->size); - writew(make16(p->nop_cmds[next_nop]), &p->xmit_cmds[0]->cmd_link); - writew(make16(p->nop_cmds[next_nop]), - &p->nop_cmds[next_nop]->cmd_link); - writew(0, &p->xmit_cmds[0]->cmd_status); - writew(0, &p->nop_cmds[next_nop]->cmd_status); - - writew(make16(p->xmit_cmds[0]), &p->nop_cmds[p->nop_point]->cmd_link); - p->nop_point = next_nop; - dev_kfree_skb(skb); -# endif -#else - writew(TBD_LAST | len, &p->xmit_buffs[p->xmit_count]->size); - next_nop = p->xmit_count + 1 - if (next_nop == NUM_XMIT_BUFFS) - next_nop = 0; - writew(0, &p->xmit_cmds[p->xmit_count]->cmd_status); - /* linkpointer of xmit-command already points to next nop cmd */ - writew(make16(p->nop_cmds[next_nop]), - &p->nop_cmds[next_nop]->cmd_link); - writew(0, &p->nop_cmds[next_nop]->cmd_status); - writew(make16(p->xmit_cmds[p->xmit_count]), - &p->nop_cmds[p->xmit_count]->cmd_link); - p->xmit_count = next_nop; - { - unsigned long flags; - spin_lock_irqsave(&p->spinlock); - if (p->xmit_count != p->xmit_last) - netif_wake_queue(dev); - spin_unlock_irqrestore(&p->spinlock); - } - dev_kfree_skb(skb); -#endif - return NETDEV_TX_OK; -} - -/******************************************* - * Someone wanna have the statistics - */ - -static struct net_device_stats *ni52_get_stats(struct net_device *dev) -{ - struct priv *p = netdev_priv(dev); - unsigned short crc, aln, rsc, ovrn; - - /* Get error-statistics from the ni82586 */ - crc = readw(&p->scb->crc_errs); - writew(0, &p->scb->crc_errs); - aln = readw(&p->scb->aln_errs); - writew(0, &p->scb->aln_errs); - rsc = readw(&p->scb->rsc_errs); - writew(0, &p->scb->rsc_errs); - ovrn = readw(&p->scb->ovrn_errs); - writew(0, &p->scb->ovrn_errs); - - dev->stats.rx_crc_errors += crc; - dev->stats.rx_fifo_errors += ovrn; - dev->stats.rx_frame_errors += aln; - dev->stats.rx_dropped += rsc; - - return &dev->stats; -} - -/******************************************************** - * Set MC list .. - */ - -static void set_multicast_list(struct net_device *dev) -{ - netif_stop_queue(dev); - ni_disint(); - alloc586(dev); - init586(dev); - startrecv586(dev); - ni_enaint(); - netif_wake_queue(dev); -} - -#ifdef MODULE -static struct net_device *dev_ni52; - -module_param(io, int, 0); -module_param(irq, int, 0); -module_param(memstart, long, 0); -module_param(memend, long, 0); -MODULE_PARM_DESC(io, "NI5210 I/O base address,required"); -MODULE_PARM_DESC(irq, "NI5210 IRQ number,required"); -MODULE_PARM_DESC(memstart, "NI5210 memory base address,required"); -MODULE_PARM_DESC(memend, "NI5210 memory end address,required"); - -int __init init_module(void) -{ - if (io <= 0x0 || !memend || !memstart || irq < 2) { - printk(KERN_ERR "ni52: Autoprobing not allowed for modules.\n"); - printk(KERN_ERR "ni52: Set symbols 'io' 'irq' 'memstart' and 'memend'\n"); - return -ENODEV; - } - dev_ni52 = ni52_probe(-1); - if (IS_ERR(dev_ni52)) - return PTR_ERR(dev_ni52); - return 0; -} - -void __exit cleanup_module(void) -{ - struct priv *p = netdev_priv(dev_ni52); - unregister_netdev(dev_ni52); - iounmap(p->mapped); - release_region(dev_ni52->base_addr, NI52_TOTAL_SIZE); - free_netdev(dev_ni52); -} -#endif /* MODULE */ - -MODULE_LICENSE("GPL"); |