diff options
Diffstat (limited to 'drivers/net/ni52.c')
| -rw-r--r-- | drivers/net/ni52.c | 1386 |
1 files changed, 1386 insertions, 0 deletions
diff --git a/drivers/net/ni52.c b/drivers/net/ni52.c new file mode 100644 index 00000000000..fa854c8fde7 --- /dev/null +++ b/drivers/net/ni52.c @@ -0,0 +1,1386 @@ +/* + * net-3-driver for the NI5210 card (i82586 Ethernet chip) + * + * This is an extension to the Linux operating system, and is covered by the + * same GNU General Public License that covers that work. + * + * Alphacode 0.82 (96/09/29) for Linux 2.0.0 (or later) + * Copyrights (c) 1994,1995,1996 by M.Hipp (hippm@informatik.uni-tuebingen.de) + * [feel free to mail ....] + * + * when using as module: (no autoprobing!) + * compile with: + * gcc -O2 -fomit-frame-pointer -m486 -D__KERNEL__ -DMODULE -c ni52.c + * run with e.g: + * insmod ni52.o io=0x360 irq=9 memstart=0xd0000 memend=0xd4000 + * + * CAN YOU PLEASE REPORT ME YOUR PERFORMANCE EXPERIENCES !!. + * + * If you find a bug, please report me: + * The kernel panic output and any kmsg from the ni52 driver + * the ni5210-driver-version and the linux-kernel version + * how many shared memory (memsize) on the netcard, + * bootprom: yes/no, base_addr, mem_start + * maybe the ni5210-card revision and the i82586 version + * + * autoprobe for: base_addr: 0x300,0x280,0x360,0x320,0x340 + * mem_start: 0xd0000,0xd2000,0xc8000,0xca000,0xd4000,0xd6000, + * 0xd8000,0xcc000,0xce000,0xda000,0xdc000 + * + * sources: + * skeleton.c from Donald Becker + * + * I have also done a look in the following sources: (mail me if you need them) + * crynwr-packet-driver by Russ Nelson + * Garret A. Wollman's (fourth) i82586-driver for BSD + * (before getting an i82596 (yes 596 not 586) manual, the existing drivers helped + * me a lot to understand this tricky chip.) + * + * Known Problems: + * The internal sysbus seems to be slow. So we often lose packets because of + * overruns while receiving from a fast remote host. + * This can slow down TCP connections. Maybe the newer ni5210 cards are better. + * my experience is, that if a machine sends with more than about 500-600K/s + * the fifo/sysbus overflows. + * + * IMPORTANT NOTE: + * On fast networks, it's a (very) good idea to have 16K shared memory. With + * 8K, we can store only 4 receive frames, so it can (easily) happen that a remote + * machine 'overruns' our system. + * + * Known i82586/card problems (I'm sure, there are many more!): + * Running the NOP-mode, the i82586 sometimes seems to forget to report + * every xmit-interrupt until we restart the CU. + * Another MAJOR bug is, that the RU sometimes seems to ignore the EL-Bit + * in the RBD-Struct which indicates an end of the RBD queue. + * Instead, the RU fetches another (randomly selected and + * usually used) RBD and begins to fill it. (Maybe, this happens only if + * the last buffer from the previous RFD fits exact into the queue and + * the next RFD can't fetch an initial RBD. Anyone knows more? ) + * + * results from ftp performance tests with Linux 1.2.5 + * send and receive about 350-400 KByte/s (peak up to 460 kbytes/s) + * sending in NOP-mode: peak performance up to 530K/s (but better don't run this mode) + */ + +/* + * 29.Sept.96: virt_to_bus changes for new memory scheme + * 19.Feb.96: more Mcast changes, module support (MH) + * + * 18.Nov.95: Mcast changes (AC). + * + * 23.April.95: fixed(?) receiving problems by configuring a RFD more + * than the number of RBD's. Can maybe cause other problems. + * 18.April.95: Added MODULE support (MH) + * 17.April.95: MC related changes in init586() and set_multicast_list(). + * removed use of 'jiffies' in init586() (MH) + * + * 19.Sep.94: Added Multicast support (not tested yet) (MH) + * + * 18.Sep.94: Workaround for 'EL-Bug'. Removed flexible RBD-handling. + * Now, every RFD has exact one RBD. (MH) + * + * 14.Sep.94: added promiscuous mode, a few cleanups (MH) + * + * 19.Aug.94: changed request_irq() parameter (MH) + * + * 20.July.94: removed cleanup bugs, removed a 16K-mem-probe-bug (MH) + * + * 19.July.94: lotsa cleanups .. (MH) + * + * 17.July.94: some patches ... verified to run with 1.1.29 (MH) + * + * 4.July.94: patches for Linux 1.1.24 (MH) + * + * 26.March.94: patches for Linux 1.0 and iomem-auto-probe (MH) + * + * 30.Sep.93: Added nop-chain .. driver now runs with only one Xmit-Buff, too (MH) + * + * < 30.Sep.93: first versions + */ + +static int debuglevel; /* debug-printk 0: off 1: a few 2: more */ +static int automatic_resume; /* experimental .. better should be zero */ +static int rfdadd; /* rfdadd=1 may be better for 8K MEM cards */ +static int fifo=0x8; /* don't change */ + +/* #define REALLY_SLOW_IO */ + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/string.h> +#include <linux/errno.h> +#include <linux/ioport.h> +#include <linux/slab.h> +#include <linux/interrupt.h> +#include <linux/delay.h> +#include <linux/init.h> +#include <linux/bitops.h> +#include <asm/io.h> + +#include <linux/netdevice.h> +#include <linux/etherdevice.h> +#include <linux/skbuff.h> + +#include "ni52.h" + +#define DRV_NAME "ni52" + +#define DEBUG /* debug on */ +#define SYSBUSVAL 1 /* 8 Bit */ + +#define ni_attn586() {outb(0,dev->base_addr+NI52_ATTENTION);} +#define ni_reset586() {outb(0,dev->base_addr+NI52_RESET);} +#define ni_disint() {outb(0,dev->base_addr+NI52_INTDIS);} +#define ni_enaint() {outb(0,dev->base_addr+NI52_INTENA);} + +#define make32(ptr16) (p->memtop + (short) (ptr16) ) +#define make24(ptr32) ( ((char *) (ptr32)) - p->base) +#define make16(ptr32) ((unsigned short) ((unsigned long)(ptr32) - (unsigned long) p->memtop )) + +/******************* how to calculate the buffers ***************************** + + * IMPORTANT NOTE: if you configure only one NUM_XMIT_BUFFS, the driver works + * --------------- in a different (more stable?) mode. Only in this mode it's + * possible to configure the driver with 'NO_NOPCOMMANDS' + +sizeof(scp)=12; sizeof(scb)=16; sizeof(iscp)=8; +sizeof(scp)+sizeof(iscp)+sizeof(scb) = 36 = INIT +sizeof(rfd) = 24; sizeof(rbd) = 12; +sizeof(tbd) = 8; sizeof(transmit_cmd) = 16; +sizeof(nop_cmd) = 8; + + * if you don't know the driver, better do not change these values: */ + +#define RECV_BUFF_SIZE 1524 /* slightly oversized */ +#define XMIT_BUFF_SIZE 1524 /* slightly oversized */ +#define NUM_XMIT_BUFFS 1 /* config for both, 8K and 16K shmem */ +#define NUM_RECV_BUFFS_8 4 /* config for 8K shared mem */ +#define NUM_RECV_BUFFS_16 9 /* config for 16K shared mem */ +#define NO_NOPCOMMANDS /* only possible with NUM_XMIT_BUFFS=1 */ + +/**************************************************************************/ + +/* different DELAYs */ +#define DELAY(x) mdelay(32 * x); +#define DELAY_16(); { udelay(16); } +#define DELAY_18(); { udelay(4); } + +/* wait for command with timeout: */ +#define WAIT_4_SCB_CMD() \ +{ int i; \ + for(i=0;i<16384;i++) { \ + if(!p->scb->cmd_cuc) break; \ + DELAY_18(); \ + if(i == 16383) { \ + printk("%s: scb_cmd timed out: %04x,%04x .. disabling i82586!!\n",dev->name,p->scb->cmd_cuc,p->scb->cus); \ + if(!p->reseted) { p->reseted = 1; ni_reset586(); } } } } + +#define WAIT_4_SCB_CMD_RUC() { int i; \ + for(i=0;i<16384;i++) { \ + if(!p->scb->cmd_ruc) break; \ + DELAY_18(); \ + if(i == 16383) { \ + printk("%s: scb_cmd (ruc) timed out: %04x,%04x .. disabling i82586!!\n",dev->name,p->scb->cmd_ruc,p->scb->rus); \ + if(!p->reseted) { p->reseted = 1; ni_reset586(); } } } } + +#define WAIT_4_STAT_COMPL(addr) { int i; \ + for(i=0;i<32767;i++) { \ + if((addr)->cmd_status & STAT_COMPL) break; \ + DELAY_16(); DELAY_16(); } } + +#define NI52_TOTAL_SIZE 16 +#define NI52_ADDR0 0x02 +#define NI52_ADDR1 0x07 +#define NI52_ADDR2 0x01 + +static int ni52_probe1(struct net_device *dev,int ioaddr); +static irqreturn_t ni52_interrupt(int irq,void *dev_id,struct pt_regs *reg_ptr); +static int ni52_open(struct net_device *dev); +static int ni52_close(struct net_device *dev); +static int ni52_send_packet(struct sk_buff *,struct net_device *); +static struct net_device_stats *ni52_get_stats(struct net_device *dev); +static void set_multicast_list(struct net_device *dev); +static void ni52_timeout(struct net_device *dev); +#if 0 +static void ni52_dump(struct net_device *,void *); +#endif + +/* helper-functions */ +static int init586(struct net_device *dev); +static int check586(struct net_device *dev,char *where,unsigned size); +static void alloc586(struct net_device *dev); +static void startrecv586(struct net_device *dev); +static void *alloc_rfa(struct net_device *dev,void *ptr); +static void ni52_rcv_int(struct net_device *dev); +static void ni52_xmt_int(struct net_device *dev); +static void ni52_rnr_int(struct net_device *dev); + +struct priv +{ + struct net_device_stats stats; + unsigned long base; + char *memtop; + long int lock; + int reseted; + volatile struct rfd_struct *rfd_last,*rfd_top,*rfd_first; + volatile struct scp_struct *scp; /* volatile is important */ + volatile struct iscp_struct *iscp; /* volatile is important */ + volatile struct scb_struct *scb; /* volatile is important */ + volatile struct tbd_struct *xmit_buffs[NUM_XMIT_BUFFS]; +#if (NUM_XMIT_BUFFS == 1) + volatile struct transmit_cmd_struct *xmit_cmds[2]; + volatile struct nop_cmd_struct *nop_cmds[2]; +#else + volatile struct transmit_cmd_struct *xmit_cmds[NUM_XMIT_BUFFS]; + volatile struct nop_cmd_struct *nop_cmds[NUM_XMIT_BUFFS]; +#endif + volatile int nop_point,num_recv_buffs; + volatile char *xmit_cbuffs[NUM_XMIT_BUFFS]; + volatile int xmit_count,xmit_last; +}; + +/********************************************** + * close device + */ +static int ni52_close(struct net_device *dev) +{ + free_irq(dev->irq, dev); + + ni_reset586(); /* the hard way to stop the receiver */ + + netif_stop_queue(dev); + + return 0; +} + +/********************************************** + * open device + */ +static int ni52_open(struct net_device *dev) +{ + int ret; + + ni_disint(); + alloc586(dev); + init586(dev); + startrecv586(dev); + ni_enaint(); + + ret = request_irq(dev->irq, &ni52_interrupt,0,dev->name,dev); + if (ret) + { + ni_reset586(); + return ret; + } + + netif_start_queue(dev); + + return 0; /* most done by init */ +} + +/********************************************** + * Check to see if there's an 82586 out there. + */ +static int check586(struct net_device *dev,char *where,unsigned size) +{ + struct priv pb; + struct priv *p = /* (struct priv *) dev->priv*/ &pb; + char *iscp_addrs[2]; + int i; + + p->base = (unsigned long) isa_bus_to_virt((unsigned long)where) + size - 0x01000000; + p->memtop = isa_bus_to_virt((unsigned long)where) + size; + p->scp = (struct scp_struct *)(p->base + SCP_DEFAULT_ADDRESS); + memset((char *)p->scp,0, sizeof(struct scp_struct)); + for(i=0;i<sizeof(struct scp_struct);i++) /* memory was writeable? */ + if(((char *)p->scp)[i]) + return 0; + p->scp->sysbus = SYSBUSVAL; /* 1 = 8Bit-Bus, 0 = 16 Bit */ + if(p->scp->sysbus != SYSBUSVAL) + return 0; + + iscp_addrs[0] = isa_bus_to_virt((unsigned long)where); + iscp_addrs[1]= (char *) p->scp - sizeof(struct iscp_struct); + + for(i=0;i<2;i++) + { + p->iscp = (struct iscp_struct *) iscp_addrs[i]; + memset((char *)p->iscp,0, sizeof(struct iscp_struct)); + + p->scp->iscp = make24(p->iscp); + p->iscp->busy = 1; + + ni_reset586(); + ni_attn586(); + DELAY(1); /* wait a while... */ + + if(p->iscp->busy) /* i82586 clears 'busy' after successful init */ + return 0; + } + return 1; +} + +/****************************************************************** + * set iscp at the right place, called by ni52_probe1 and open586. + */ +static void alloc586(struct net_device *dev) +{ + struct priv *p = (struct priv *) dev->priv; + + ni_reset586(); + DELAY(1); + + p->scp = (struct scp_struct *) (p->base + SCP_DEFAULT_ADDRESS); + p->scb = (struct scb_struct *) isa_bus_to_virt(dev->mem_start); + p->iscp = (struct iscp_struct *) ((char *)p->scp - sizeof(struct iscp_struct)); + + memset((char *) p->iscp,0,sizeof(struct iscp_struct)); + memset((char *) p->scp ,0,sizeof(struct scp_struct)); + + p->scp->iscp = make24(p->iscp); + p->scp->sysbus = SYSBUSVAL; + p->iscp->scb_offset = make16(p->scb); + + p->iscp->busy = 1; + ni_reset586(); + ni_attn586(); + + DELAY(1); + + if(p->iscp->busy) + printk("%s: Init-Problems (alloc).\n",dev->name); + + p->reseted = 0; + + memset((char *)p->scb,0,sizeof(struct scb_struct)); +} + +/* set: io,irq,memstart,memend or set it when calling insmod */ +static int irq=9; +static int io=0x300; +static long memstart; /* e.g 0xd0000 */ +static long memend; /* e.g 0xd4000 */ + +/********************************************** + * probe the ni5210-card + */ +struct net_device * __init ni52_probe(int unit) +{ + struct net_device *dev = alloc_etherdev(sizeof(struct priv)); + static int ports[] = {0x300, 0x280, 0x360 , 0x320 , 0x340, 0}; + int *port; + int err = 0; + + if (!dev) + return ERR_PTR(-ENOMEM); + + if (unit >= 0) { + sprintf(dev->name, "eth%d", unit); + netdev_boot_setup_check(dev); + io = dev->base_addr; + irq = dev->irq; + memstart = dev->mem_start; + memend = dev->mem_end; + } + + SET_MODULE_OWNER(dev); + + if (io > 0x1ff) { /* Check a single specified location. */ + err = ni52_probe1(dev, io); + } else if (io > 0) { /* Don't probe at all. */ + err = -ENXIO; + } else { + for (port = ports; *port && ni52_probe1(dev, *port) ; port++) + ; + if (*port) + goto got_it; +#ifdef FULL_IO_PROBE + for (io = 0x200; io < 0x400 && ni52_probe1(dev, io); io += 8) + ; + if (io < 0x400) + goto got_it; +#endif + err = -ENODEV; + } + if (err) + goto out; +got_it: + err = register_netdev(dev); + if (err) + goto out1; + return dev; +out1: + release_region(dev->base_addr, NI52_TOTAL_SIZE); +out: + free_netdev(dev); + return ERR_PTR(err); +} + +static int __init ni52_probe1(struct net_device *dev,int ioaddr) +{ + int i, size, retval; + + dev->base_addr = ioaddr; + dev->irq = irq; + dev->mem_start = memstart; + dev->mem_end = memend; + + if (!request_region(ioaddr, NI52_TOTAL_SIZE, DRV_NAME)) + return -EBUSY; + + if( !(inb(ioaddr+NI52_MAGIC1) == NI52_MAGICVAL1) || + !(inb(ioaddr+NI52_MAGIC2) == NI52_MAGICVAL2)) { + retval = -ENODEV; + goto out; + } + + for(i=0;i<ETH_ALEN;i++) + dev->dev_addr[i] = inb(dev->base_addr+i); + + if(dev->dev_addr[0] != NI52_ADDR0 || dev->dev_addr[1] != NI52_ADDR1 + || dev->dev_addr[2] != NI52_ADDR2) { + retval = -ENODEV; + goto out; + } + + printk(KERN_INFO "%s: NI5210 found at %#3lx, ",dev->name,dev->base_addr); + + /* + * check (or search) IO-Memory, 8K and 16K + */ +#ifdef MODULE + size = dev->mem_end - dev->mem_start; + if(size != 0x2000 && size != 0x4000) { + printk("\n%s: Illegal memory size %d. Allowed is 0x2000 or 0x4000 bytes.\n",dev->name,size); + retval = -ENODEV; + goto out; + } + if(!check586(dev,(char *) dev->mem_start,size)) { + printk("?memcheck, Can't find memory at 0x%lx with size %d!\n",dev->mem_start,size); + retval = -ENODEV; + goto out; + } +#else + if(dev->mem_start != 0) /* no auto-mem-probe */ + { + size = 0x4000; /* check for 16K mem */ + if(!check586(dev,(char *) dev->mem_start,size)) { + size = 0x2000; /* check for 8K mem */ + if(!check586(dev,(char *) dev->mem_start,size)) { + printk("?memprobe, Can't find memory at 0x%lx!\n",dev->mem_start); + retval = -ENODEV; + goto out; + } + } + } + else + { + static long memaddrs[] = { 0xc8000,0xca000,0xcc000,0xce000,0xd0000,0xd2000, + 0xd4000,0xd6000,0xd8000,0xda000,0xdc000, 0 }; + for(i=0;;i++) + { + if(!memaddrs[i]) { + printk("?memprobe, Can't find io-memory!\n"); + retval = -ENODEV; + goto out; + } + dev->mem_start = memaddrs[i]; + size = 0x2000; /* check for 8K mem */ + if(check586(dev,(char *)dev->mem_start,size)) /* 8K-check */ + break; + size = 0x4000; /* check for 16K mem */ + if(check586(dev,(char *)dev->mem_start,size)) /* 16K-check */ + break; + } + } + dev->mem_end = dev->mem_start + size; /* set mem_end showed by 'ifconfig' */ +#endif + + memset((char *) dev->priv,0,sizeof(struct priv)); + + ((struct priv *) (dev->priv))->memtop = isa_bus_to_virt(dev->mem_start) + size; + ((struct priv *) (dev->priv))->base = (unsigned long) isa_bus_to_virt(dev->mem_start) + size - 0x01000000; + alloc586(dev); + + /* set number of receive-buffs according to memsize */ + if(size == 0x2000) + ((struct priv *) dev->priv)->num_recv_buffs = NUM_RECV_BUFFS_8; + else + ((struct priv *) dev->priv)->num_recv_buffs = NUM_RECV_BUFFS_16; + + printk("Memaddr: 0x%lx, Memsize: %d, ",dev->mem_start,size); + + if(dev->irq < 2) + { + unsigned long irq_mask; + + irq_mask = probe_irq_on(); + ni_reset586(); + ni_attn586(); + + mdelay(20); + dev->irq = probe_irq_off(irq_mask); + if(!dev->irq) + { + printk("?autoirq, Failed to detect IRQ line!\n"); + retval = -EAGAIN; + goto out; + } + printk("IRQ %d (autodetected).\n",dev->irq); + } + else { + if(dev->irq == 2) + dev->irq = 9; + printk("IRQ %d (assigned and not checked!).\n",dev->irq); + } + + dev->open = ni52_open; + dev->stop = ni52_close; + dev->get_stats = ni52_get_stats; + dev->tx_timeout = ni52_timeout; + dev->watchdog_timeo = HZ/20; + dev->hard_start_xmit = ni52_send_packet; + dev->set_multicast_list = set_multicast_list; + + dev->if_port = 0; + + return 0; +out: + release_region(ioaddr, NI52_TOTAL_SIZE); + return retval; +} + +/********************************************** + * init the chip (ni52-interrupt should be disabled?!) + * needs a correct 'allocated' memory + */ + +static int init586(struct net_device *dev) +{ + void *ptr; + int i,result=0; + struct priv *p = (struct priv *) dev->priv; + volatile struct configure_cmd_struct *cfg_cmd; + volatile struct iasetup_cmd_struct *ias_cmd; + volatile struct tdr_cmd_struct *tdr_cmd; + volatile struct mcsetup_cmd_struct *mc_cmd; + struct dev_mc_list *dmi=dev->mc_list; + int num_addrs=dev->mc_count; + + ptr = (void *) ((char *)p->scb + sizeof(struct scb_struct)); + + cfg_cmd = (struct configure_cmd_struct *)ptr; /* configure-command */ + cfg_cmd->cmd_status = 0; + cfg_cmd->cmd_cmd = CMD_CONFIGURE | CMD_LAST; + cfg_cmd->cmd_link = 0xffff; + + cfg_cmd->byte_cnt = 0x0a; /* number of cfg bytes */ + cfg_cmd->fifo = fifo; /* fifo-limit (8=tx:32/rx:64) */ + cfg_cmd->sav_bf = 0x40; /* hold or discard bad recv frames (bit 7) */ + cfg_cmd->adr_len = 0x2e; /* addr_len |!src_insert |pre-len |loopback */ + cfg_cmd->priority = 0x00; + cfg_cmd->ifs = 0x60; + cfg_cmd->time_low = 0x00; + cfg_cmd->time_high = 0xf2; + cfg_cmd->promisc = 0; + if(dev->flags & IFF_ALLMULTI) { + int len = ((char *) p->iscp - (char *) ptr - 8) / 6; + if(num_addrs > len) { + printk("%s: switching to promisc. mode\n",dev->name); + dev->flags|=IFF_PROMISC; + } + } + if(dev->flags&IFF_PROMISC) + { + cfg_cmd->promisc=1; + dev->flags|=IFF_PROMISC; + } + cfg_cmd->carr_coll = 0x00; + + p->scb->cbl_offset = make16(cfg_cmd); + p->scb->cmd_ruc = 0; + + p->scb->cmd_cuc = CUC_START; /* cmd.-unit start */ + ni_attn586(); + + WAIT_4_STAT_COMPL(cfg_cmd); + + if((cfg_cmd->cmd_status & (STAT_OK|STAT_COMPL)) != (STAT_COMPL|STAT_OK)) + { + printk("%s: configure command failed: %x\n",dev->name,cfg_cmd->cmd_status); + return 1; + } + + /* + * individual address setup + */ + + ias_cmd = (struct iasetup_cmd_struct *)ptr; + + ias_cmd->cmd_status = 0; + ias_cmd->cmd_cmd = CMD_IASETUP | CMD_LAST; + ias_cmd->cmd_link = 0xffff; + + memcpy((char *)&ias_cmd->iaddr,(char *) dev->dev_addr,ETH_ALEN); + + p->scb->cbl_offset = make16(ias_cmd); + + p->scb->cmd_cuc = CUC_START; /* cmd.-unit start */ + ni_attn586(); + + WAIT_4_STAT_COMPL(ias_cmd); + + if((ias_cmd->cmd_status & (STAT_OK|STAT_COMPL)) != (STAT_OK|STAT_COMPL)) { + printk("%s (ni52): individual address setup command failed: %04x\n",dev->name,ias_cmd->cmd_status); + return 1; + } + + /* + * TDR, wire check .. e.g. no resistor e.t.c + */ + + tdr_cmd = (struct tdr_cmd_struct *)ptr; + + tdr_cmd->cmd_status = 0; + tdr_cmd->cmd_cmd = CMD_TDR | CMD_LAST; + tdr_cmd->cmd_link = 0xffff; + tdr_cmd->status = 0; + + p->scb->cbl_offset = make16(tdr_cmd); + p->scb->cmd_cuc = CUC_START; /* cmd.-unit start */ + ni_attn586(); + + WAIT_4_STAT_COMPL(tdr_cmd); + + if(!(tdr_cmd->cmd_status & STAT_COMPL)) + { + printk("%s: Problems while running the TDR.\n",dev->name); + } + else + { + DELAY_16(); /* wait for result */ + result = tdr_cmd->status; + + p->scb->cmd_cuc = p->scb->cus & STAT_MASK; + ni_attn586(); /* ack the interrupts */ + + if(result & TDR_LNK_OK) + ; + else if(result & TDR_XCVR_PRB) + printk("%s: TDR: Transceiver problem. Check the cable(s)!\n",dev->name); + else if(result & TDR_ET_OPN) + printk("%s: TDR: No correct termination %d clocks away.\n",dev->name,result & TDR_TIMEMASK); + else if(result & TDR_ET_SRT) + { + if (result & TDR_TIMEMASK) /* time == 0 -> strange :-) */ + printk("%s: TDR: Detected a short circuit %d clocks away.\n",dev->name,result & TDR_TIMEMASK); + } + else + printk("%s: TDR: Unknown status %04x\n",dev->name,result); + } + + /* + * Multicast setup + */ + if(num_addrs && !(dev->flags & IFF_PROMISC) ) + { + mc_cmd = (struct mcsetup_cmd_struct *) ptr; + mc_cmd->cmd_status = 0; + mc_cmd->cmd_cmd = CMD_MCSETUP | CMD_LAST; + mc_cmd->cmd_link = 0xffff; + mc_cmd->mc_cnt = num_addrs * 6; + + for(i=0;i<num_addrs;i++,dmi=dmi->next) + memcpy((char *) mc_cmd->mc_list[i], dmi->dmi_addr,6); + + p->scb->cbl_offset = make16(mc_cmd); + p->scb->cmd_cuc = CUC_START; + ni_attn586(); + + WAIT_4_STAT_COMPL(mc_cmd); + + if( (mc_cmd->cmd_status & (STAT_COMPL|STAT_OK)) != (STAT_COMPL|STAT_OK) ) + printk("%s: Can't apply multicast-address-list.\n",dev->name); + } + + /* + * alloc nop/xmit-cmds + */ +#if (NUM_XMIT_BUFFS == 1) + for(i=0;i<2;i++) + { + p->nop_cmds[i] = (struct nop_cmd_struct *)ptr; + p->nop_cmds[i]->cmd_cmd = CMD_NOP; + p->nop_cmds[i]->cmd_status = 0; + p->nop_cmds[i]->cmd_link = make16((p->nop_cmds[i])); + ptr = (char *) ptr + sizeof(struct nop_cmd_struct); + } +#else + for(i=0;i<NUM_XMIT_BUFFS;i++) + { + p->nop_cmds[i] = (struct nop_cmd_struct *)ptr; + p->nop_cmds[i]->cmd_cmd = CMD_NOP; + p->nop_cmds[i]->cmd_status = 0; + p->nop_cmds[i]->cmd_link = make16((p->nop_cmds[i])); + ptr = (char *) ptr + sizeof(struct nop_cmd_struct); + } +#endif + + ptr = alloc_rfa(dev,(void *)ptr); /* init receive-frame-area */ + + /* + * alloc xmit-buffs / init xmit_cmds + */ + for(i=0;i<NUM_XMIT_BUFFS;i++) + { + p->xmit_cmds[i] = (struct transmit_cmd_struct *)ptr; /*transmit cmd/buff 0*/ + ptr = (char *) ptr + sizeof(struct transmit_cmd_struct); + p->xmit_cbuffs[i] = (char *)ptr; /* char-buffs */ + ptr = (char *) ptr + XMIT_BUFF_SIZE; + p->xmit_buffs[i] = (struct tbd_struct *)ptr; /* TBD */ + ptr = (char *) ptr + sizeof(struct tbd_struct); + if((void *)ptr > (void *)p->iscp) + { + printk("%s: not enough shared-mem for your configuration!\n",dev->name); + return 1; + } + memset((char *)(p->xmit_cmds[i]) ,0, sizeof(struct transmit_cmd_struct)); + memset((char *)(p->xmit_buffs[i]),0, sizeof(struct tbd_struct)); + p->xmit_cmds[i]->cmd_link = make16(p->nop_cmds[(i+1)%NUM_XMIT_BUFFS]); + p->xmit_cmds[i]->cmd_status = STAT_COMPL; + p->xmit_cmds[i]->cmd_cmd = CMD_XMIT | CMD_INT; + p->xmit_cmds[i]->tbd_offset = make16((p->xmit_buffs[i])); + p->xmit_buffs[i]->next = 0xffff; + p->xmit_buffs[i]->buffer = make24((p->xmit_cbuffs[i])); + } + + p->xmit_count = 0; + p->xmit_last = 0; +#ifndef NO_NOPCOMMANDS + p->nop_point = 0; +#endif + + /* + * 'start transmitter' + */ +#ifndef NO_NOPCOMMANDS + p->scb->cbl_offset = make16(p->nop_cmds[0]); + p->scb->cmd_cuc = CUC_START; + ni_attn586(); + WAIT_4_SCB_CMD(); +#else + p->xmit_cmds[0]->cmd_link = make16(p->xmit_cmds[0]); + p->xmit_cmds[0]->cmd_cmd = CMD_XMIT | CMD_SUSPEND | CMD_INT; +#endif + + /* + * ack. interrupts + */ + p->scb->cmd_cuc = p->scb->cus & STAT_MASK; + ni_attn586(); + DELAY_16(); + + ni_enaint(); + + return 0; +} + +/****************************************************** + * This is a helper routine for ni52_rnr_int() and init586(). + * It sets up the Receive Frame Area (RFA). + */ + +static void *alloc_rfa(struct net_device *dev,void *ptr) +{ + volatile struct rfd_struct *rfd = (struct rfd_struct *)ptr; + volatile struct rbd_struct *rbd; + int i; + struct priv *p = (struct priv *) dev->priv; + + memset((char *) rfd,0,sizeof(struct rfd_struct)*(p->num_recv_buffs+rfdadd)); + p->rfd_first = rfd; + + for(i = 0; i < (p->num_recv_buffs+rfdadd); i++) { + rfd[i].next = make16(rfd + (i+1) % (p->num_recv_buffs+rfdadd) ); + rfd[i].rbd_offset = 0xffff; + } + rfd[p->num_recv_buffs-1+rfdadd].last = RFD_SUSP; /* RU suspend */ + + ptr = (void *) (rfd + (p->num_recv_buffs + rfdadd) ); + + rbd = (struct rbd_struct *) ptr; + ptr = (void *) (rbd + p->num_recv_buffs); + + /* clr descriptors */ + memset((char *) rbd,0,sizeof(struct rbd_struct)*(p->num_recv_buffs)); + + for(i=0;i<p->num_recv_buffs;i++) + { + rbd[i].next = make16((rbd + (i+1) % p->num_recv_buffs)); + rbd[i].size = RECV_BUFF_SIZE; + rbd[i].buffer = make24(ptr); + ptr = (char *) ptr + RECV_BUFF_SIZE; + } + + p->rfd_top = p->rfd_first; + p->rfd_last = p->rfd_first + (p->num_recv_buffs - 1 + rfdadd); + + p->scb->rfa_offset = make16(p->rfd_first); + p->rfd_first->rbd_offset = make16(rbd); + + return ptr; +} + + +/************************************************** + * Interrupt Handler ... + */ + +static irqreturn_t ni52_interrupt(int irq,void *dev_id,struct pt_regs *reg_ptr) +{ + struct net_device *dev = dev_id; + unsigned short stat; + int cnt=0; + struct priv *p; + + if (!dev) { + printk ("ni5210-interrupt: irq %d for unknown device.\n",irq); + return IRQ_NONE; + } + p = (struct priv *) dev->priv; + + if(debuglevel > 1) + printk("I"); + + WAIT_4_SCB_CMD(); /* wait for last command */ + + while((stat=p->scb->cus & STAT_MASK)) + { + p->scb->cmd_cuc = stat; + ni_attn586(); + + if(stat & STAT_FR) /* received a frame */ + ni52_rcv_int(dev); + + if(stat & STAT_RNR) /* RU went 'not ready' */ + { + printk("(R)"); + if(p->scb->rus & RU_SUSPEND) /* special case: RU_SUSPEND */ + { + WAIT_4_SCB_CMD(); + p->scb->cmd_ruc = RUC_RESUME; + ni_attn586(); + WAIT_4_SCB_CMD_RUC(); + } + else + { + printk("%s: Receiver-Unit went 'NOT READY': %04x/%02x.\n",dev->name,(int) stat,(int) p->scb->rus); + ni52_rnr_int(dev); + } + } + + if(stat & STAT_CX) /* command with I-bit set complete */ + ni52_xmt_int(dev); + +#ifndef NO_NOPCOMMANDS + if(stat & STAT_CNA) /* CU went 'not ready' */ + { + if(netif_running(dev)) + printk("%s: oops! CU has left active state. stat: %04x/%02x.\n",dev->name,(int) stat,(int) p->scb->cus); + } +#endif + + if(debuglevel > 1) + printk("%d",cnt++); + + WAIT_4_SCB_CMD(); /* wait for ack. (ni52_xmt_int can be faster than ack!!) */ + if(p->scb->cmd_cuc) /* timed out? */ + { + printk("%s: Acknowledge timed out.\n",dev->name); + ni_disint(); + break; + } + } + + if(debuglevel > 1) + printk("i"); + return IRQ_HANDLED; +} + +/******************************************************* + * receive-interrupt + */ + +static void ni52_rcv_int(struct net_device *dev) +{ + int status,cnt=0; + unsigned short totlen; + struct sk_buff *skb; + struct rbd_struct *rbd; + struct priv *p = (struct priv *) dev->priv; + + if(debuglevel > 0) + printk("R"); + + for(;(status = p->rfd_top->stat_high) & RFD_COMPL;) + { + rbd = (struct rbd_struct *) make32(p->rfd_top->rbd_offset); + + if(status & RFD_OK) /* frame received without error? */ + { + if( (totlen = rbd->status) & RBD_LAST) /* the first and the last buffer? */ + { + totlen &= RBD_MASK; /* length of this frame */ + rbd->status = 0; + skb = (struct sk_buff *) dev_alloc_skb(totlen+2); + if(skb != NULL) + { + skb->dev = dev; + skb_reserve(skb,2); + skb_put(skb,totlen); + eth_copy_and_sum(skb,(char *) p->base+(unsigned long) rbd->buffer,totlen,0); + skb->protocol=eth_type_trans(skb,dev); + netif_rx(skb); + dev->last_rx = jiffies; + p->stats.rx_packets++; + p->stats.rx_bytes += totlen; + } + else + p->stats.rx_dropped++; + } + else + { + int rstat; + /* free all RBD's until RBD_LAST is set */ + totlen = 0; + while(!((rstat=rbd->status) & RBD_LAST)) + { + totlen += rstat & RBD_MASK; + if(!rstat) + { + printk("%s: Whoops .. no end mark in RBD list\n",dev->name); + break; + } + rbd->status = 0; + rbd = (struct rbd_struct *) make32(rbd->next); + } + totlen += rstat & RBD_MASK; + rbd->status = 0; + printk("%s: received oversized frame! length: %d\n",dev->name,totlen); + p->stats.rx_dropped++; + } + } + else /* frame !(ok), only with 'save-bad-frames' */ + { + printk("%s: oops! rfd-error-status: %04x\n",dev->name,status); + p->stats.rx_errors++; + } + p->rfd_top->stat_high = 0; + p->rfd_top->last = RFD_SUSP; /* maybe exchange by RFD_LAST */ + p->rfd_top->rbd_offset = 0xffff; + p->rfd_last->last = 0; /* delete RFD_SUSP */ + p->rfd_last = p->rfd_top; + p->rfd_top = (struct rfd_struct *) make32(p->rfd_top->next); /* step to next RFD */ + p->scb->rfa_offset = make16(p->rfd_top); + + if(debuglevel > 0) + printk("%d",cnt++); + } + + if(automatic_resume) + { + WAIT_4_SCB_CMD(); + p->scb->cmd_ruc = RUC_RESUME; + ni_attn586(); + WAIT_4_SCB_CMD_RUC(); + } + +#ifdef WAIT_4_BUSY + { + int i; + for(i=0;i<1024;i++) + { + if(p->rfd_top->status) + break; + DELAY_16(); + if(i == 1023) + printk("%s: RU hasn't fetched next RFD (not busy/complete)\n",dev->name); + } + } +#endif + +#if 0 + if(!at_least_one) + { + int i; + volatile struct rfd_struct *rfds=p->rfd_top; + volatile struct rbd_struct *rbds; + printk("%s: received a FC intr. without having a frame: %04x %d\n",dev->name,status,old_at_least); + for(i=0;i< (p->num_recv_buffs+4);i++) + { + rbds = (struct rbd_struct *) make32(rfds->rbd_offset); + printk("%04x:%04x ",rfds->status,rbds->status); + rfds = (struct rfd_struct *) make32(rfds->next); + } + printk("\nerrs: %04x %04x stat: %04x\n",(int)p->scb->rsc_errs,(int)p->scb->ovrn_errs,(int)p->scb->status); + printk("\nerrs: %04x %04x rus: %02x, cus: %02x\n",(int)p->scb->rsc_errs,(int)p->scb->ovrn_errs,(int)p->scb->rus,(int)p->scb->cus); + } + old_at_least = at_least_one; +#endif + + if(debuglevel > 0) + printk("r"); +} + +/********************************************************** + * handle 'Receiver went not ready'. + */ + +static void ni52_rnr_int(struct net_device *dev) +{ + struct priv *p = (struct priv *) dev->priv; + + p->stats.rx_errors++; + + WAIT_4_SCB_CMD(); /* wait for the last cmd, WAIT_4_FULLSTAT?? */ + p->scb->cmd_ruc = RUC_ABORT; /* usually the RU is in the 'no resource'-state .. abort it now. */ + ni_attn586(); + WAIT_4_SCB_CMD_RUC(); /* wait for accept cmd. */ + + alloc_rfa(dev,(char *)p->rfd_first); +/* maybe add a check here, before restarting the RU */ + startrecv586(dev); /* restart RU */ + + printk("%s: Receive-Unit restarted. Status: %04x\n",dev->name,p->scb->rus); + +} + +/********************************************************** + * handle xmit - interrupt + */ + +static void ni52_xmt_int(struct net_device *dev) +{ + int status; + struct priv *p = (struct priv *) dev->priv; + + if(debuglevel > 0) + printk("X"); + + status = p->xmit_cmds[p->xmit_last]->cmd_status; + if(!(status & STAT_COMPL)) + printk("%s: strange .. xmit-int without a 'COMPLETE'\n",dev->name); + + if(status & STAT_OK) + { + p->stats.tx_packets++; + p->stats.collisions += (status & TCMD_MAXCOLLMASK); + } + else + { + p->stats.tx_errors++; + if(status & TCMD_LATECOLL) { + printk("%s: late collision detected.\n",dev->name); + p->stats.collisions++; + } + else if(status & TCMD_NOCARRIER) { + p->stats.tx_carrier_errors++; + printk("%s: no carrier detected.\n",dev->name); + } + else if(status & TCMD_LOSTCTS) + printk("%s: loss of CTS detected.\n",dev->name); + else if(status & TCMD_UNDERRUN) { + p->stats.tx_fifo_errors++; + printk("%s: DMA underrun detected.\n",dev->name); + } + else if(status & TCMD_MAXCOLL) { + printk("%s: Max. collisions exceeded.\n",dev->name); + p->stats.collisions += 16; + } + } + +#if (NUM_XMIT_BUFFS > 1) + if( (++p->xmit_last) == NUM_XMIT_BUFFS) + p->xmit_last = 0; +#endif + netif_wake_queue(dev); +} + +/*********************************************************** + * (re)start the receiver + */ + +static void startrecv586(struct net_device *dev) +{ + struct priv *p = (struct priv *) dev->priv; + + WAIT_4_SCB_CMD(); + WAIT_4_SCB_CMD_RUC(); + p->scb->rfa_offset = make16(p->rfd_first); + p->scb->cmd_ruc = RUC_START; + ni_attn586(); /* start cmd. */ + WAIT_4_SCB_CMD_RUC(); /* wait for accept cmd. (no timeout!!) */ +} + +static void ni52_timeout(struct net_device *dev) +{ + struct priv *p = (struct priv *) dev->priv; +#ifndef NO_NOPCOMMANDS + if(p->scb->cus & CU_ACTIVE) /* COMMAND-UNIT active? */ + { + netif_wake_queue(dev); +#ifdef DEBUG + printk("%s: strange ... timeout with CU active?!?\n",dev->name); + printk("%s: X0: %04x N0: %04x N1: %04x %d\n",dev->name,(int)p->xmit_cmds[0]->cmd_status,(int)p->nop_cmds[0]->cmd_status,(int)p->nop_cmds[1]->cmd_status,(int)p->nop_point); +#endif + p->scb->cmd_cuc = CUC_ABORT; + ni_attn586(); + WAIT_4_SCB_CMD(); + p->scb->cbl_offset = make16(p->nop_cmds[p->nop_point]); + p->scb->cmd_cuc = CUC_START; + ni_attn586(); + WAIT_4_SCB_CMD(); + dev->trans_start = jiffies; + return 0; + } +#endif + { +#ifdef DEBUG + printk("%s: xmitter timed out, try to restart! stat: %02x\n",dev->name,p->scb->cus); + printk("%s: command-stats: %04x %04x\n",dev->name,p->xmit_cmds[0]->cmd_status,p->xmit_cmds[1]->cmd_status); + printk("%s: check, whether you set the right interrupt number!\n",dev->name); +#endif + ni52_close(dev); + ni52_open(dev); + } + dev->trans_start = jiffies; +} + +/****************************************************** + * send frame + */ + +static int ni52_send_packet(struct sk_buff *skb, struct net_device *dev) +{ + int len,i; +#ifndef NO_NOPCOMMANDS + int next_nop; +#endif + struct priv *p = (struct priv *) dev->priv; + + if(skb->len > XMIT_BUFF_SIZE) + { + printk("%s: Sorry, max. framelength is %d bytes. The length of your frame is %d bytes.\n",dev->name,XMIT_BUFF_SIZE,skb->len); + return 0; + } + + netif_stop_queue(dev); + +#if(NUM_XMIT_BUFFS > 1) + if(test_and_set_bit(0,(void *) &p->lock)) { + printk("%s: Queue was locked\n",dev->name); + return 1; + } + else +#endif + { + memcpy((char *)p->xmit_cbuffs[p->xmit_count],(char *)(skb->data),skb->len); + len = skb->len; + if (len < ETH_ZLEN) { + len = ETH_ZLEN; + memset((char *)p->xmit_cbuffs[p->xmit_count]+skb->len, 0, len - skb->len); + } + +#if (NUM_XMIT_BUFFS == 1) +# ifdef NO_NOPCOMMANDS + +#ifdef DEBUG + if(p->scb->cus & CU_ACTIVE) + { + printk("%s: Hmmm .. CU is still running and we wanna send a new packet.\n",dev->name); + printk("%s: stat: %04x %04x\n",dev->name,p->scb->cus,p->xmit_cmds[0]->cmd_status); + } +#endif + + p->xmit_buffs[0]->size = TBD_LAST | len; + for(i=0;i<16;i++) + { + p->xmit_cmds[0]->cmd_status = 0; + WAIT_4_SCB_CMD(); + if( (p->scb->cus & CU_STATUS) == CU_SUSPEND) + p->scb->cmd_cuc = CUC_RESUME; + else + { + p->scb->cbl_offset = make16(p->xmit_cmds[0]); + p->scb->cmd_cuc = CUC_START; + } + + ni_attn586(); + dev->trans_start = jiffies; + if(!i) + dev_kfree_skb(skb); + WAIT_4_SCB_CMD(); + if( (p->scb->cus & CU_ACTIVE)) /* test it, because CU sometimes doesn't start immediately */ + break; + if(p->xmit_cmds[0]->cmd_status) + break; + if(i==15) + printk("%s: Can't start transmit-command.\n",dev->name); + } +# else + next_nop = (p->nop_point + 1) & 0x1; + p->xmit_buffs[0]->size = TBD_LAST | len; + + p->xmit_cmds[0]->cmd_link = p->nop_cmds[next_nop]->cmd_link + = make16((p->nop_cmds[next_nop])); + p->xmit_cmds[0]->cmd_status = p->nop_cmds[next_nop]->cmd_status = 0; + + p->nop_cmds[p->nop_point]->cmd_link = make16((p->xmit_cmds[0])); + dev->trans_start = jiffies; + p->nop_point = next_nop; + dev_kfree_skb(skb); +# endif +#else + p->xmit_buffs[p->xmit_count]->size = TBD_LAST | len; + if( (next_nop = p->xmit_count + 1) == NUM_XMIT_BUFFS ) + next_nop = 0; + + p->xmit_cmds[p->xmit_count]->cmd_status = 0; + /* linkpointer of xmit-command already points to next nop cmd */ + p->nop_cmds[next_nop]->cmd_link = make16((p->nop_cmds[next_nop])); + p->nop_cmds[next_nop]->cmd_status = 0; + + p->nop_cmds[p->xmit_count]->cmd_link = make16((p->xmit_cmds[p->xmit_count])); + dev->trans_start = jiffies; + p->xmit_count = next_nop; + + { + unsigned long flags; + save_flags(flags); + cli(); + if(p->xmit_count != p->xmit_last) + netif_wake_queue(dev); + p->lock = 0; + restore_flags(flags); + } + dev_kfree_skb(skb); +#endif + } + return 0; +} + +/******************************************* + * Someone wanna have the statistics + */ + +static struct net_device_stats *ni52_get_stats(struct net_device *dev) +{ + struct priv *p = (struct priv *) dev->priv; + unsigned short crc,aln,rsc,ovrn; + + crc = p->scb->crc_errs; /* get error-statistic from the ni82586 */ + p->scb->crc_errs = 0; + aln = p->scb->aln_errs; + p->scb->aln_errs = 0; + rsc = p->scb->rsc_errs; + p->scb->rsc_errs = 0; + ovrn = p->scb->ovrn_errs; + p->scb->ovrn_errs = 0; + + p->stats.rx_crc_errors += crc; + p->stats.rx_fifo_errors += ovrn; + p->stats.rx_frame_errors += aln; + p->stats.rx_dropped += rsc; + + return &p->stats; +} + +/******************************************************** + * Set MC list .. + */ + +static void set_multicast_list(struct net_device *dev) +{ + netif_stop_queue(dev); + ni_disint(); + alloc586(dev); + init586(dev); + startrecv586(dev); + ni_enaint(); + netif_wake_queue(dev); +} + +#ifdef MODULE +static struct net_device *dev_ni52; + +module_param(io, int, 0); +module_param(irq, int, 0); +module_param(memstart, long, 0); +module_param(memend, long, 0); +MODULE_PARM_DESC(io, "NI5210 I/O base address,required"); +MODULE_PARM_DESC(irq, "NI5210 IRQ number,required"); +MODULE_PARM_DESC(memstart, "NI5210 memory base address,required"); +MODULE_PARM_DESC(memend, "NI5210 memory end address,required"); + +int init_module(void) +{ + if(io <= 0x0 || !memend || !memstart || irq < 2) { + printk("ni52: Autoprobing not allowed for modules.\nni52: Set symbols 'io' 'irq' 'memstart' and 'memend'\n"); + return -ENODEV; + } + dev_ni52 = ni52_probe(-1); + if (IS_ERR(dev_ni52)) + return PTR_ERR(dev_ni52); + return 0; +} + +void cleanup_module(void) +{ + unregister_netdev(dev_ni52); + release_region(dev_ni52->base_addr, NI52_TOTAL_SIZE); + free_netdev(dev_ni52); +} +#endif /* MODULE */ + +#if 0 +/* + * DUMP .. we expect a not running CMD unit and enough space + */ +void ni52_dump(struct net_device *dev,void *ptr) +{ + struct priv *p = (struct priv *) dev->priv; + struct dump_cmd_struct *dump_cmd = (struct dump_cmd_struct *) ptr; + int i; + + p->scb->cmd_cuc = CUC_ABORT; + ni_attn586(); + WAIT_4_SCB_CMD(); + WAIT_4_SCB_CMD_RUC(); + + dump_cmd->cmd_status = 0; + dump_cmd->cmd_cmd = CMD_DUMP | CMD_LAST; + dump_cmd->dump_offset = make16((dump_cmd + 1)); + dump_cmd->cmd_link = 0xffff; + + p->scb->cbl_offset = make16(dump_cmd); + p->scb->cmd_cuc = CUC_START; + ni_attn586(); + WAIT_4_STAT_COMPL(dump_cmd); + + if( (dump_cmd->cmd_status & (STAT_COMPL|STAT_OK)) != (STAT_COMPL|STAT_OK) ) + printk("%s: Can't get dump information.\n",dev->name); + + for(i=0;i<170;i++) { + printk("%02x ",(int) ((unsigned char *) (dump_cmd + 1))[i]); + if(i % 24 == 23) + printk("\n"); + } + printk("\n"); +} +#endif +MODULE_LICENSE("GPL"); + +/* + * END: linux/drivers/net/ni52.c + */ |