diff options
Diffstat (limited to 'drivers/net/phy/smsc.c')
| -rw-r--r-- | drivers/net/phy/smsc.c | 95 |
1 files changed, 68 insertions, 27 deletions
diff --git a/drivers/net/phy/smsc.c b/drivers/net/phy/smsc.c index 88e3991464e..11f34813e23 100644 --- a/drivers/net/phy/smsc.c +++ b/drivers/net/phy/smsc.c @@ -43,7 +43,31 @@ static int smsc_phy_ack_interrupt(struct phy_device *phydev) static int smsc_phy_config_init(struct phy_device *phydev) { - int rc = phy_read(phydev, MII_LAN83C185_CTRL_STATUS); + int rc = phy_read(phydev, MII_LAN83C185_SPECIAL_MODES); + if (rc < 0) + return rc; + + /* If the SMSC PHY is in power down mode, then set it + * in all capable mode before using it. + */ + if ((rc & MII_LAN83C185_MODE_MASK) == MII_LAN83C185_MODE_POWERDOWN) { + int timeout = 50000; + + /* set "all capable" mode and reset the phy */ + rc |= MII_LAN83C185_MODE_ALL; + phy_write(phydev, MII_LAN83C185_SPECIAL_MODES, rc); + phy_write(phydev, MII_BMCR, BMCR_RESET); + + /* wait end of reset (max 500 ms) */ + do { + udelay(10); + if (timeout-- == 0) + return -1; + rc = phy_read(phydev, MII_BMCR); + } while (rc & BMCR_RESET); + } + + rc = phy_read(phydev, MII_LAN83C185_CTRL_STATUS); if (rc < 0) return rc; @@ -56,35 +80,52 @@ static int smsc_phy_config_init(struct phy_device *phydev) return smsc_phy_ack_interrupt (phydev); } -static int lan87xx_config_init(struct phy_device *phydev) +static int lan911x_config_init(struct phy_device *phydev) { - /* - * Make sure the EDPWRDOWN bit is NOT set. Setting this bit on - * LAN8710/LAN8720 PHY causes the PHY to misbehave, likely due - * to a bug on the chip. - * - * When the system is powered on with the network cable being - * disconnected all the way until after ifconfig ethX up is - * issued for the LAN port with this PHY, connecting the cable - * afterwards does not cause LINK change detection, while the - * expected behavior is the Link UP being detected. - */ - int rc = phy_read(phydev, MII_LAN83C185_CTRL_STATUS); - if (rc < 0) - return rc; - - rc &= ~MII_LAN83C185_EDPWRDOWN; - - rc = phy_write(phydev, MII_LAN83C185_CTRL_STATUS, rc); - if (rc < 0) - return rc; - return smsc_phy_ack_interrupt(phydev); } -static int lan911x_config_init(struct phy_device *phydev) +/* + * The LAN8710/LAN8720 requires a minimum of 2 link pulses within 64ms of each + * other in order to set the ENERGYON bit and exit EDPD mode. If a link partner + * does send the pulses within this interval, the PHY will remained powered + * down. + * + * This workaround will manually toggle the PHY on/off upon calls to read_status + * in order to generate link test pulses if the link is down. If a link partner + * is present, it will respond to the pulses, which will cause the ENERGYON bit + * to be set and will cause the EDPD mode to be exited. + */ +static int lan87xx_read_status(struct phy_device *phydev) { - return smsc_phy_ack_interrupt(phydev); + int err = genphy_read_status(phydev); + + if (!phydev->link) { + /* Disable EDPD to wake up PHY */ + int rc = phy_read(phydev, MII_LAN83C185_CTRL_STATUS); + if (rc < 0) + return rc; + + rc = phy_write(phydev, MII_LAN83C185_CTRL_STATUS, + rc & ~MII_LAN83C185_EDPWRDOWN); + if (rc < 0) + return rc; + + /* Sleep 64 ms to allow ~5 link test pulses to be sent */ + msleep(64); + + /* Re-enable EDPD */ + rc = phy_read(phydev, MII_LAN83C185_CTRL_STATUS); + if (rc < 0) + return rc; + + rc = phy_write(phydev, MII_LAN83C185_CTRL_STATUS, + rc | MII_LAN83C185_EDPWRDOWN); + if (rc < 0) + return rc; + } + + return err; } static struct phy_driver smsc_phy_driver[] = { @@ -187,8 +228,8 @@ static struct phy_driver smsc_phy_driver[] = { /* basic functions */ .config_aneg = genphy_config_aneg, - .read_status = genphy_read_status, - .config_init = lan87xx_config_init, + .read_status = lan87xx_read_status, + .config_init = smsc_phy_config_init, /* IRQ related */ .ack_interrupt = smsc_phy_ack_interrupt, |