diff options
Diffstat (limited to 'drivers/net/ppp/Kconfig')
| -rw-r--r-- | drivers/net/ppp/Kconfig | 175 |
1 files changed, 175 insertions, 0 deletions
diff --git a/drivers/net/ppp/Kconfig b/drivers/net/ppp/Kconfig new file mode 100644 index 00000000000..872df3ef07a --- /dev/null +++ b/drivers/net/ppp/Kconfig @@ -0,0 +1,175 @@ +# +# PPP network device configuration +# + +config PPP + tristate "PPP (point-to-point protocol) support" + select SLHC + ---help--- + PPP (Point to Point Protocol) is a newer and better SLIP. It serves + the same purpose: sending Internet traffic over telephone (and other + serial) lines. Ask your access provider if they support it, because + otherwise you can't use it; most Internet access providers these + days support PPP rather than SLIP. + + To use PPP, you need an additional program called pppd as described + in the PPP-HOWTO, available at + <http://www.tldp.org/docs.html#howto>. Make sure that you have + the version of pppd recommended in <file:Documentation/Changes>. + The PPP option enlarges your kernel by about 16 KB. + + There are actually two versions of PPP: the traditional PPP for + asynchronous lines, such as regular analog phone lines, and + synchronous PPP which can be used over digital ISDN lines for + example. If you want to use PPP over phone lines or other + asynchronous serial lines, you need to say Y (or M) here and also to + the next option, "PPP support for async serial ports". For PPP over + synchronous lines, you should say Y (or M) here and to "Support + synchronous PPP", below. + + If you said Y to "Version information on all symbols" above, then + you cannot compile the PPP driver into the kernel; you can then only + compile it as a module. To compile this driver as a module, choose M + here. The module will be called ppp_generic. + +if PPP + +config PPP_BSDCOMP + tristate "PPP BSD-Compress compression" + depends on PPP + ---help--- + Support for the BSD-Compress compression method for PPP, which uses + the LZW compression method to compress each PPP packet before it is + sent over the wire. The machine at the other end of the PPP link + (usually your ISP) has to support the BSD-Compress compression + method as well for this to be useful. Even if they don't support it, + it is safe to say Y here. + + The PPP Deflate compression method ("PPP Deflate compression", + above) is preferable to BSD-Compress, because it compresses better + and is patent-free. + + Note that the BSD compression code will always be compiled as a + module; it is called bsd_comp and will show up in the directory + modules once you have said "make modules". If unsure, say N. + +config PPP_DEFLATE + tristate "PPP Deflate compression" + depends on PPP + select ZLIB_INFLATE + select ZLIB_DEFLATE + ---help--- + Support for the Deflate compression method for PPP, which uses the + Deflate algorithm (the same algorithm that gzip uses) to compress + each PPP packet before it is sent over the wire. The machine at the + other end of the PPP link (usually your ISP) has to support the + Deflate compression method as well for this to be useful. Even if + they don't support it, it is safe to say Y here. + + To compile this driver as a module, choose M here. + +config PPP_FILTER + bool "PPP filtering" + depends on PPP + ---help--- + Say Y here if you want to be able to filter the packets passing over + PPP interfaces. This allows you to control which packets count as + activity (i.e. which packets will reset the idle timer or bring up + a demand-dialed link) and which packets are to be dropped entirely. + You need to say Y here if you wish to use the pass-filter and + active-filter options to pppd. + + If unsure, say N. + +config PPP_MPPE + tristate "PPP MPPE compression (encryption) (EXPERIMENTAL)" + depends on PPP && EXPERIMENTAL + select CRYPTO + select CRYPTO_SHA1 + select CRYPTO_ARC4 + select CRYPTO_ECB + ---help--- + Support for the MPPE Encryption protocol, as employed by the + Microsoft Point-to-Point Tunneling Protocol. + + See http://pptpclient.sourceforge.net/ for information on + configuring PPTP clients and servers to utilize this method. + +config PPP_MULTILINK + bool "PPP multilink support (EXPERIMENTAL)" + depends on PPP && EXPERIMENTAL + ---help--- + PPP multilink is a protocol (defined in RFC 1990) which allows you + to combine several (logical or physical) lines into one logical PPP + connection, so that you can utilize your full bandwidth. + + This has to be supported at the other end as well and you need a + version of the pppd daemon which understands the multilink protocol. + + If unsure, say N. + +config PPPOATM + tristate "PPP over ATM" + depends on ATM && PPP + ---help--- + Support PPP (Point to Point Protocol) encapsulated in ATM frames. + This implementation does not yet comply with section 8 of RFC2364, + which can lead to bad results if the ATM peer loses state and + changes its encapsulation unilaterally. + +config PPPOE + tristate "PPP over Ethernet (EXPERIMENTAL)" + depends on EXPERIMENTAL && PPP + ---help--- + Support for PPP over Ethernet. + + This driver requires the latest version of pppd from the CVS + repository at cvs.samba.org. Alternatively, see the + RoaringPenguin package (<http://www.roaringpenguin.com/pppoe>) + which contains instruction on how to use this driver (under + the heading "Kernel mode PPPoE"). + +config PPTP + tristate "PPP over IPv4 (PPTP) (EXPERIMENTAL)" + depends on EXPERIMENTAL && PPP && NET_IPGRE_DEMUX + ---help--- + Support for PPP over IPv4.(Point-to-Point Tunneling Protocol) + + This driver requires pppd plugin to work in client mode or + modified pptpd (poptop) to work in server mode. + See http://accel-pptp.sourceforge.net/ for information how to + utilize this module. + +config PPPOL2TP + tristate "PPP over L2TP (EXPERIMENTAL)" + depends on EXPERIMENTAL && L2TP && PPP + ---help--- + Support for PPP-over-L2TP socket family. L2TP is a protocol + used by ISPs and enterprises to tunnel PPP traffic over UDP + tunnels. L2TP is replacing PPTP for VPN uses. + +config PPP_ASYNC + tristate "PPP support for async serial ports" + depends on PPP + select CRC_CCITT + ---help--- + Say Y (or M) here if you want to be able to use PPP over standard + asynchronous serial ports, such as COM1 or COM2 on a PC. If you use + a modem (not a synchronous or ISDN modem) to contact your ISP, you + need this option. + + To compile this driver as a module, choose M here. + + If unsure, say Y. + +config PPP_SYNC_TTY + tristate "PPP support for sync tty ports" + depends on PPP + ---help--- + Say Y (or M) here if you want to be able to use PPP over synchronous + (HDLC) tty devices, such as the SyncLink adapter. These devices + are often used for high-speed leased lines like T1/E1. + + To compile this driver as a module, choose M here. + +endif # PPP |