summaryrefslogtreecommitdiffstats
path: root/drivers/net/sfc/sfe4001.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/sfc/sfe4001.c')
-rw-r--r--drivers/net/sfc/sfe4001.c244
1 files changed, 154 insertions, 90 deletions
diff --git a/drivers/net/sfc/sfe4001.c b/drivers/net/sfc/sfe4001.c
index b2784952399..b7005da55d5 100644
--- a/drivers/net/sfc/sfe4001.c
+++ b/drivers/net/sfc/sfe4001.c
@@ -13,11 +13,13 @@
* the PHY
*/
#include <linux/delay.h>
+#include "net_driver.h"
#include "efx.h"
#include "phy.h"
#include "boards.h"
#include "falcon.h"
#include "falcon_hwdefs.h"
+#include "falcon_io.h"
#include "mac.h"
/**************************************************************************
@@ -120,111 +122,63 @@ static void sfe4001_poweroff(struct efx_nic *efx)
i2c_smbus_read_byte_data(hwmon_client, RSL);
}
-static void sfe4001_fini(struct efx_nic *efx)
-{
- EFX_INFO(efx, "%s\n", __func__);
-
- sfe4001_poweroff(efx);
- i2c_unregister_device(efx->board_info.ioexp_client);
- i2c_unregister_device(efx->board_info.hwmon_client);
-}
-
-/* The P0_EN_3V3X line on SFE4001 boards (from A2 onward) is connected
- * to the FLASH_CFG_1 input on the DSP. We must keep it high at power-
- * up to allow writing the flash (done through MDIO from userland).
- */
-unsigned int sfe4001_phy_flash_cfg;
-module_param_named(phy_flash_cfg, sfe4001_phy_flash_cfg, uint, 0444);
-MODULE_PARM_DESC(phy_flash_cfg,
- "Force PHY to enter flash configuration mode");
-
-/* This board uses an I2C expander to provider power to the PHY, which needs to
- * be turned on before the PHY can be used.
- * Context: Process context, rtnl lock held
- */
-int sfe4001_init(struct efx_nic *efx)
+static int sfe4001_poweron(struct efx_nic *efx)
{
- struct i2c_client *hwmon_client, *ioexp_client;
- unsigned int count;
+ struct i2c_client *hwmon_client = efx->board_info.hwmon_client;
+ struct i2c_client *ioexp_client = efx->board_info.ioexp_client;
+ unsigned int i, j;
int rc;
u8 out;
- efx_dword_t reg;
-
- hwmon_client = i2c_new_dummy(&efx->i2c_adap, MAX6647);
- if (!hwmon_client)
- return -EIO;
- efx->board_info.hwmon_client = hwmon_client;
-
- ioexp_client = i2c_new_dummy(&efx->i2c_adap, PCA9539);
- if (!ioexp_client) {
- rc = -EIO;
- goto fail_hwmon;
- }
- efx->board_info.ioexp_client = ioexp_client;
-
- /* 10Xpress has fixed-function LED pins, so there is no board-specific
- * blink code. */
- efx->board_info.blink = tenxpress_phy_blink;
+ efx_oword_t reg;
/* Ensure that XGXS and XAUI SerDes are held in reset */
- EFX_POPULATE_DWORD_7(reg, XX_PWRDNA_EN, 1,
+ EFX_POPULATE_OWORD_7(reg, XX_PWRDNA_EN, 1,
XX_PWRDNB_EN, 1,
XX_RSTPLLAB_EN, 1,
XX_RESETA_EN, 1,
XX_RESETB_EN, 1,
XX_RSTXGXSRX_EN, 1,
XX_RSTXGXSTX_EN, 1);
- falcon_xmac_writel(efx, &reg, XX_PWR_RST_REG_MAC);
+ falcon_write(efx, &reg, XX_PWR_RST_REG);
udelay(10);
- efx->board_info.fini = sfe4001_fini;
-
- /* Set DSP over-temperature alert threshold */
- EFX_INFO(efx, "DSP cut-out at %dC\n", xgphy_max_temperature);
- rc = i2c_smbus_write_byte_data(hwmon_client, WLHO,
- xgphy_max_temperature);
- if (rc)
- goto fail_ioexp;
-
- /* Read it back and verify */
- rc = i2c_smbus_read_byte_data(hwmon_client, RLHN);
- if (rc < 0)
- goto fail_ioexp;
- if (rc != xgphy_max_temperature) {
- rc = -EFAULT;
- goto fail_ioexp;
- }
-
/* Clear any previous over-temperature alert */
rc = i2c_smbus_read_byte_data(hwmon_client, RSL);
if (rc < 0)
- goto fail_ioexp;
+ return rc;
/* Enable port 0 and port 1 outputs on IO expander */
rc = i2c_smbus_write_byte_data(ioexp_client, P0_CONFIG, 0x00);
if (rc)
- goto fail_ioexp;
+ return rc;
rc = i2c_smbus_write_byte_data(ioexp_client, P1_CONFIG,
0xff & ~(1 << P1_SPARE_LBN));
if (rc)
goto fail_on;
- /* Turn all power off then wait 1 sec. This ensures PHY is reset */
+ /* If PHY power is on, turn it all off and wait 1 second to
+ * ensure a full reset.
+ */
+ rc = i2c_smbus_read_byte_data(ioexp_client, P0_OUT);
+ if (rc < 0)
+ goto fail_on;
out = 0xff & ~((0 << P0_EN_1V2_LBN) | (0 << P0_EN_2V5_LBN) |
(0 << P0_EN_3V3X_LBN) | (0 << P0_EN_5V_LBN) |
(0 << P0_EN_1V0X_LBN));
- rc = i2c_smbus_write_byte_data(ioexp_client, P0_OUT, out);
- if (rc)
- goto fail_on;
+ if (rc != out) {
+ EFX_INFO(efx, "power-cycling PHY\n");
+ rc = i2c_smbus_write_byte_data(ioexp_client, P0_OUT, out);
+ if (rc)
+ goto fail_on;
+ schedule_timeout_uninterruptible(HZ);
+ }
- schedule_timeout_uninterruptible(HZ);
- count = 0;
- do {
+ for (i = 0; i < 20; ++i) {
/* Turn on 1.2V, 2.5V, 3.3V and 5V power rails */
out = 0xff & ~((1 << P0_EN_1V2_LBN) | (1 << P0_EN_2V5_LBN) |
(1 << P0_EN_3V3X_LBN) | (1 << P0_EN_5V_LBN) |
(1 << P0_X_TRST_LBN));
- if (sfe4001_phy_flash_cfg)
+ if (efx->phy_mode & PHY_MODE_SPECIAL)
out |= 1 << P0_EN_3V3X_LBN;
rc = i2c_smbus_write_byte_data(ioexp_client, P0_OUT, out);
@@ -238,35 +192,145 @@ int sfe4001_init(struct efx_nic *efx)
if (rc)
goto fail_on;
- EFX_INFO(efx, "waiting for power (attempt %d)...\n", count);
+ EFX_INFO(efx, "waiting for DSP boot (attempt %d)...\n", i);
+
+ /* In flash config mode, DSP does not turn on AFE, so
+ * just wait 1 second.
+ */
+ if (efx->phy_mode & PHY_MODE_SPECIAL) {
+ schedule_timeout_uninterruptible(HZ);
+ return 0;
+ }
+
+ for (j = 0; j < 10; ++j) {
+ msleep(100);
+
+ /* Check DSP has asserted AFE power line */
+ rc = i2c_smbus_read_byte_data(ioexp_client, P1_IN);
+ if (rc < 0)
+ goto fail_on;
+ if (rc & (1 << P1_AFE_PWD_LBN))
+ return 0;
+ }
+ }
- schedule_timeout_uninterruptible(HZ);
+ EFX_INFO(efx, "timed out waiting for DSP boot\n");
+ rc = -ETIMEDOUT;
+fail_on:
+ sfe4001_poweroff(efx);
+ return rc;
+}
- /* Check DSP is powered */
- rc = i2c_smbus_read_byte_data(ioexp_client, P1_IN);
- if (rc < 0)
- goto fail_on;
- if (rc & (1 << P1_AFE_PWD_LBN))
- goto done;
+/* On SFE4001 rev A2 and later, we can control the FLASH_CFG_1 pin
+ * using the 3V3X output of the IO-expander. Allow the user to set
+ * this when the device is stopped, and keep it stopped then.
+ */
- /* DSP doesn't look powered in flash config mode */
- if (sfe4001_phy_flash_cfg)
- goto done;
- } while (++count < 20);
+static ssize_t show_phy_flash_cfg(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct efx_nic *efx = pci_get_drvdata(to_pci_dev(dev));
+ return sprintf(buf, "%d\n", !!(efx->phy_mode & PHY_MODE_SPECIAL));
+}
- EFX_INFO(efx, "timed out waiting for power\n");
- rc = -ETIMEDOUT;
- goto fail_on;
+static ssize_t set_phy_flash_cfg(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct efx_nic *efx = pci_get_drvdata(to_pci_dev(dev));
+ enum efx_phy_mode old_mode, new_mode;
+ int err;
+
+ rtnl_lock();
+ old_mode = efx->phy_mode;
+ if (count == 0 || *buf == '0')
+ new_mode = old_mode & ~PHY_MODE_SPECIAL;
+ else
+ new_mode = PHY_MODE_SPECIAL;
+ if (old_mode == new_mode) {
+ err = 0;
+ } else if (efx->state != STATE_RUNNING || netif_running(efx->net_dev)) {
+ err = -EBUSY;
+ } else {
+ efx->phy_mode = new_mode;
+ err = sfe4001_poweron(efx);
+ efx_reconfigure_port(efx);
+ }
+ rtnl_unlock();
+
+ return err ? err : count;
+}
+
+static DEVICE_ATTR(phy_flash_cfg, 0644, show_phy_flash_cfg, set_phy_flash_cfg);
+
+static void sfe4001_fini(struct efx_nic *efx)
+{
+ EFX_INFO(efx, "%s\n", __func__);
+
+ device_remove_file(&efx->pci_dev->dev, &dev_attr_phy_flash_cfg);
+ sfe4001_poweroff(efx);
+ i2c_unregister_device(efx->board_info.ioexp_client);
+ i2c_unregister_device(efx->board_info.hwmon_client);
+}
+
+/* This board uses an I2C expander to provider power to the PHY, which needs to
+ * be turned on before the PHY can be used.
+ * Context: Process context, rtnl lock held
+ */
+int sfe4001_init(struct efx_nic *efx)
+{
+ struct i2c_client *hwmon_client;
+ int rc;
+
+ hwmon_client = i2c_new_dummy(&efx->i2c_adap, MAX6647);
+ if (!hwmon_client)
+ return -EIO;
+ efx->board_info.hwmon_client = hwmon_client;
+
+ /* Set DSP over-temperature alert threshold */
+ EFX_INFO(efx, "DSP cut-out at %dC\n", xgphy_max_temperature);
+ rc = i2c_smbus_write_byte_data(hwmon_client, WLHO,
+ xgphy_max_temperature);
+ if (rc)
+ goto fail_ioexp;
+
+ /* Read it back and verify */
+ rc = i2c_smbus_read_byte_data(hwmon_client, RLHN);
+ if (rc < 0)
+ goto fail_ioexp;
+ if (rc != xgphy_max_temperature) {
+ rc = -EFAULT;
+ goto fail_ioexp;
+ }
+
+ efx->board_info.ioexp_client = i2c_new_dummy(&efx->i2c_adap, PCA9539);
+ if (!efx->board_info.ioexp_client) {
+ rc = -EIO;
+ goto fail_hwmon;
+ }
+
+ /* 10Xpress has fixed-function LED pins, so there is no board-specific
+ * blink code. */
+ efx->board_info.blink = tenxpress_phy_blink;
+
+ efx->board_info.fini = sfe4001_fini;
+
+ rc = sfe4001_poweron(efx);
+ if (rc)
+ goto fail_ioexp;
+
+ rc = device_create_file(&efx->pci_dev->dev, &dev_attr_phy_flash_cfg);
+ if (rc)
+ goto fail_on;
-done:
EFX_INFO(efx, "PHY is powered on\n");
return 0;
fail_on:
sfe4001_poweroff(efx);
fail_ioexp:
- i2c_unregister_device(ioexp_client);
+ i2c_unregister_device(efx->board_info.ioexp_client);
fail_hwmon:
- i2c_unregister_device(hwmon_client);
+ i2c_unregister_device(hwmon_client);
return rc;
}
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-12-14 06:54:29 +0000