diff options
Diffstat (limited to 'drivers/net/sk98lin/skgeinit.c')
| -rw-r--r-- | drivers/net/sk98lin/skgeinit.c | 2005 |
1 files changed, 2005 insertions, 0 deletions
diff --git a/drivers/net/sk98lin/skgeinit.c b/drivers/net/sk98lin/skgeinit.c new file mode 100644 index 00000000000..67f1d6a5c15 --- /dev/null +++ b/drivers/net/sk98lin/skgeinit.c @@ -0,0 +1,2005 @@ +/****************************************************************************** + * + * Name: skgeinit.c + * Project: Gigabit Ethernet Adapters, Common Modules + * Version: $Revision: 1.97 $ + * Date: $Date: 2003/10/02 16:45:31 $ + * Purpose: Contains functions to initialize the adapter + * + ******************************************************************************/ + +/****************************************************************************** + * + * (C)Copyright 1998-2002 SysKonnect. + * (C)Copyright 2002-2003 Marvell. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * The information in this file is provided "AS IS" without warranty. + * + ******************************************************************************/ + +#include "h/skdrv1st.h" +#include "h/skdrv2nd.h" + +/* global variables ***********************************************************/ + +/* local variables ************************************************************/ + +#if (defined(DEBUG) || ((!defined(LINT)) && (!defined(SK_SLIM)))) +static const char SysKonnectFileId[] = + "@(#) $Id: skgeinit.c,v 1.97 2003/10/02 16:45:31 rschmidt Exp $ (C) Marvell."; +#endif + +struct s_QOffTab { + int RxQOff; /* Receive Queue Address Offset */ + int XsQOff; /* Sync Tx Queue Address Offset */ + int XaQOff; /* Async Tx Queue Address Offset */ +}; +static struct s_QOffTab QOffTab[] = { + {Q_R1, Q_XS1, Q_XA1}, {Q_R2, Q_XS2, Q_XA2} +}; + +struct s_Config { + char ScanString[8]; + SK_U32 Value; +}; + +static struct s_Config OemConfig = { + {'O','E','M','_','C','o','n','f'}, +#ifdef SK_OEM_CONFIG + OEM_CONFIG_VALUE, +#else + 0, +#endif +}; + +/****************************************************************************** + * + * SkGePollTxD() - Enable / Disable Descriptor Polling of TxD Rings + * + * Description: + * Enable or disable the descriptor polling of the transmit descriptor + * ring(s) (TxD) for port 'Port'. + * The new configuration is *not* saved over any SkGeStopPort() and + * SkGeInitPort() calls. + * + * Returns: + * nothing + */ +void SkGePollTxD( +SK_AC *pAC, /* adapter context */ +SK_IOC IoC, /* IO context */ +int Port, /* Port Index (MAC_1 + n) */ +SK_BOOL PollTxD) /* SK_TRUE (enable pol.), SK_FALSE (disable pol.) */ +{ + SK_GEPORT *pPrt; + SK_U32 DWord; + + pPrt = &pAC->GIni.GP[Port]; + + DWord = (SK_U32)(PollTxD ? CSR_ENA_POL : CSR_DIS_POL); + + if (pPrt->PXSQSize != 0) { + SK_OUT32(IoC, Q_ADDR(pPrt->PXsQOff, Q_CSR), DWord); + } + + if (pPrt->PXAQSize != 0) { + SK_OUT32(IoC, Q_ADDR(pPrt->PXaQOff, Q_CSR), DWord); + } +} /* SkGePollTxD */ + + +/****************************************************************************** + * + * SkGeYellowLED() - Switch the yellow LED on or off. + * + * Description: + * Switch the yellow LED on or off. + * + * Note: + * This function may be called any time after SkGeInit(Level 1). + * + * Returns: + * nothing + */ +void SkGeYellowLED( +SK_AC *pAC, /* adapter context */ +SK_IOC IoC, /* IO context */ +int State) /* yellow LED state, 0 = OFF, 0 != ON */ +{ + if (State == 0) { + /* Switch yellow LED OFF */ + SK_OUT8(IoC, B0_LED, LED_STAT_OFF); + } + else { + /* Switch yellow LED ON */ + SK_OUT8(IoC, B0_LED, LED_STAT_ON); + } +} /* SkGeYellowLED */ + + +#if (!defined(SK_SLIM) || defined(GENESIS)) +/****************************************************************************** + * + * SkGeXmitLED() - Modify the Operational Mode of a transmission LED. + * + * Description: + * The Rx or Tx LED which is specified by 'Led' will be + * enabled, disabled or switched on in test mode. + * + * Note: + * 'Led' must contain the address offset of the LEDs INI register. + * + * Usage: + * SkGeXmitLED(pAC, IoC, MR_ADDR(Port, TX_LED_INI), SK_LED_ENA); + * + * Returns: + * nothing + */ +void SkGeXmitLED( +SK_AC *pAC, /* adapter context */ +SK_IOC IoC, /* IO context */ +int Led, /* offset to the LED Init Value register */ +int Mode) /* Mode may be SK_LED_DIS, SK_LED_ENA, SK_LED_TST */ +{ + SK_U32 LedIni; + + switch (Mode) { + case SK_LED_ENA: + LedIni = SK_XMIT_DUR * (SK_U32)pAC->GIni.GIHstClkFact / 100; + SK_OUT32(IoC, Led + XMIT_LED_INI, LedIni); + SK_OUT8(IoC, Led + XMIT_LED_CTRL, LED_START); + break; + case SK_LED_TST: + SK_OUT8(IoC, Led + XMIT_LED_TST, LED_T_ON); + SK_OUT32(IoC, Led + XMIT_LED_CNT, 100); + SK_OUT8(IoC, Led + XMIT_LED_CTRL, LED_START); + break; + case SK_LED_DIS: + default: + /* + * Do NOT stop the LED Timer here. The LED might be + * in on state. But it needs to go off. + */ + SK_OUT32(IoC, Led + XMIT_LED_CNT, 0); + SK_OUT8(IoC, Led + XMIT_LED_TST, LED_T_OFF); + break; + } + + /* + * 1000BT: The Transmit LED is driven by the PHY. + * But the default LED configuration is used for + * Level One and Broadcom PHYs. + * (Broadcom: It may be that PHY_B_PEC_EN_LTR has to be set.) + * (In this case it has to be added here. But we will see. XXX) + */ +} /* SkGeXmitLED */ +#endif /* !SK_SLIM || GENESIS */ + + +/****************************************************************************** + * + * DoCalcAddr() - Calculates the start and the end address of a queue. + * + * Description: + * This function calculates the start and the end address of a queue. + * Afterwards the 'StartVal' is incremented to the next start position. + * If the port is already initialized the calculated values + * will be checked against the configured values and an + * error will be returned, if they are not equal. + * If the port is not initialized the values will be written to + * *StartAdr and *EndAddr. + * + * Returns: + * 0: success + * 1: configuration error + */ +static int DoCalcAddr( +SK_AC *pAC, /* adapter context */ +SK_GEPORT SK_FAR *pPrt, /* port index */ +int QuSize, /* size of the queue to configure in kB */ +SK_U32 SK_FAR *StartVal, /* start value for address calculation */ +SK_U32 SK_FAR *QuStartAddr,/* start addr to calculate */ +SK_U32 SK_FAR *QuEndAddr) /* end address to calculate */ +{ + SK_U32 EndVal; + SK_U32 NextStart; + int Rtv; + + Rtv = 0; + if (QuSize == 0) { + EndVal = *StartVal; + NextStart = EndVal; + } + else { + EndVal = *StartVal + ((SK_U32)QuSize * 1024) - 1; + NextStart = EndVal + 1; + } + + if (pPrt->PState >= SK_PRT_INIT) { + if (*StartVal != *QuStartAddr || EndVal != *QuEndAddr) { + Rtv = 1; + } + } + else { + *QuStartAddr = *StartVal; + *QuEndAddr = EndVal; + } + + *StartVal = NextStart; + return(Rtv); +} /* DoCalcAddr */ + +/****************************************************************************** + * + * SkGeInitAssignRamToQueues() - allocate default queue sizes + * + * Description: + * This function assigns the memory to the different queues and ports. + * When DualNet is set to SK_TRUE all ports get the same amount of memory. + * Otherwise the first port gets most of the memory and all the + * other ports just the required minimum. + * This function can only be called when pAC->GIni.GIRamSize and + * pAC->GIni.GIMacsFound have been initialized, usually this happens + * at init level 1 + * + * Returns: + * 0 - ok + * 1 - invalid input values + * 2 - not enough memory + */ + +int SkGeInitAssignRamToQueues( +SK_AC *pAC, /* Adapter context */ +int ActivePort, /* Active Port in RLMT mode */ +SK_BOOL DualNet) /* adapter context */ +{ + int i; + int UsedKilobytes; /* memory already assigned */ + int ActivePortKilobytes; /* memory available for active port */ + SK_GEPORT *pGePort; + + UsedKilobytes = 0; + + if (ActivePort >= pAC->GIni.GIMacsFound) { + SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_INIT, + ("SkGeInitAssignRamToQueues: ActivePort (%d) invalid\n", + ActivePort)); + return(1); + } + if (((pAC->GIni.GIMacsFound * (SK_MIN_RXQ_SIZE + SK_MIN_TXQ_SIZE)) + + ((RAM_QUOTA_SYNC == 0) ? 0 : SK_MIN_TXQ_SIZE)) > pAC->GIni.GIRamSize) { + SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_INIT, + ("SkGeInitAssignRamToQueues: Not enough memory (%d)\n", + pAC->GIni.GIRamSize)); + return(2); + } + + if (DualNet) { + /* every port gets the same amount of memory */ + ActivePortKilobytes = pAC->GIni.GIRamSize / pAC->GIni.GIMacsFound; + for (i = 0; i < pAC->GIni.GIMacsFound; i++) { + + pGePort = &pAC->GIni.GP[i]; + + /* take away the minimum memory for active queues */ + ActivePortKilobytes -= (SK_MIN_RXQ_SIZE + SK_MIN_TXQ_SIZE); + + /* receive queue gets the minimum + 80% of the rest */ + pGePort->PRxQSize = (int) (ROUND_QUEUE_SIZE_KB(( + ActivePortKilobytes * (unsigned long) RAM_QUOTA_RX) / 100)) + + SK_MIN_RXQ_SIZE; + + ActivePortKilobytes -= (pGePort->PRxQSize - SK_MIN_RXQ_SIZE); + + /* synchronous transmit queue */ + pGePort->PXSQSize = 0; + + /* asynchronous transmit queue */ + pGePort->PXAQSize = (int) ROUND_QUEUE_SIZE_KB(ActivePortKilobytes + + SK_MIN_TXQ_SIZE); + } + } + else { + /* Rlmt Mode or single link adapter */ + + /* Set standby queue size defaults for all standby ports */ + for (i = 0; i < pAC->GIni.GIMacsFound; i++) { + + if (i != ActivePort) { + pGePort = &pAC->GIni.GP[i]; + + pGePort->PRxQSize = SK_MIN_RXQ_SIZE; + pGePort->PXAQSize = SK_MIN_TXQ_SIZE; + pGePort->PXSQSize = 0; + + /* Count used RAM */ + UsedKilobytes += pGePort->PRxQSize + pGePort->PXAQSize; + } + } + /* what's left? */ + ActivePortKilobytes = pAC->GIni.GIRamSize - UsedKilobytes; + + /* assign it to the active port */ + /* first take away the minimum memory */ + ActivePortKilobytes -= (SK_MIN_RXQ_SIZE + SK_MIN_TXQ_SIZE); + pGePort = &pAC->GIni.GP[ActivePort]; + + /* receive queue get's the minimum + 80% of the rest */ + pGePort->PRxQSize = (int) (ROUND_QUEUE_SIZE_KB((ActivePortKilobytes * + (unsigned long) RAM_QUOTA_RX) / 100)) + SK_MIN_RXQ_SIZE; + + ActivePortKilobytes -= (pGePort->PRxQSize - SK_MIN_RXQ_SIZE); + + /* synchronous transmit queue */ + pGePort->PXSQSize = 0; + + /* asynchronous transmit queue */ + pGePort->PXAQSize = (int) ROUND_QUEUE_SIZE_KB(ActivePortKilobytes) + + SK_MIN_TXQ_SIZE; + } +#ifdef VCPU + VCPUprintf(0, "PRxQSize=%u, PXSQSize=%u, PXAQSize=%u\n", + pGePort->PRxQSize, pGePort->PXSQSize, pGePort->PXAQSize); +#endif /* VCPU */ + + return(0); +} /* SkGeInitAssignRamToQueues */ + +/****************************************************************************** + * + * SkGeCheckQSize() - Checks the Adapters Queue Size Configuration + * + * Description: + * This function verifies the Queue Size Configuration specified + * in the variables PRxQSize, PXSQSize, and PXAQSize of all + * used ports. + * This requirements must be fullfilled to have a valid configuration: + * - The size of all queues must not exceed GIRamSize. + * - The queue sizes must be specified in units of 8 kB. + * - The size of Rx queues of available ports must not be + * smaller than 16 kB. + * - The size of at least one Tx queue (synch. or asynch.) + * of available ports must not be smaller than 16 kB + * when Jumbo Frames are used. + * - The RAM start and end addresses must not be changed + * for ports which are already initialized. + * Furthermore SkGeCheckQSize() defines the Start and End Addresses + * of all ports and stores them into the HWAC port structure. + * + * Returns: + * 0: Queue Size Configuration valid + * 1: Queue Size Configuration invalid + */ +static int SkGeCheckQSize( +SK_AC *pAC, /* adapter context */ +int Port) /* port index */ +{ + SK_GEPORT *pPrt; + int i; + int Rtv; + int Rtv2; + SK_U32 StartAddr; +#ifndef SK_SLIM + int UsedMem; /* total memory used (max. found ports) */ +#endif + + Rtv = 0; + +#ifndef SK_SLIM + + UsedMem = 0; + for (i = 0; i < pAC->GIni.GIMacsFound; i++) { + pPrt = &pAC->GIni.GP[i]; + + if ((pPrt->PRxQSize & QZ_UNITS) != 0 || + (pPrt->PXSQSize & QZ_UNITS) != 0 || + (pPrt->PXAQSize & QZ_UNITS) != 0) { + + SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_HWI_E012, SKERR_HWI_E012MSG); + return(1); + } + + if (i == Port && pPrt->PRxQSize < SK_MIN_RXQ_SIZE) { + SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_HWI_E011, SKERR_HWI_E011MSG); + return(1); + } + + /* + * the size of at least one Tx queue (synch. or asynch.) has to be > 0. + * if Jumbo Frames are used, this size has to be >= 16 kB. + */ + if ((i == Port && pPrt->PXSQSize == 0 && pPrt->PXAQSize == 0) || + (pAC->GIni.GIPortUsage == SK_JUMBO_LINK && + ((pPrt->PXSQSize > 0 && pPrt->PXSQSize < SK_MIN_TXQ_SIZE) || + (pPrt->PXAQSize > 0 && pPrt->PXAQSize < SK_MIN_TXQ_SIZE)))) { + SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_HWI_E023, SKERR_HWI_E023MSG); + return(1); + } + + UsedMem += pPrt->PRxQSize + pPrt->PXSQSize + pPrt->PXAQSize; + } + + if (UsedMem > pAC->GIni.GIRamSize) { + SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_HWI_E012, SKERR_HWI_E012MSG); + return(1); + } +#endif /* !SK_SLIM */ + + /* Now start address calculation */ + StartAddr = pAC->GIni.GIRamOffs; + for (i = 0; i < pAC->GIni.GIMacsFound; i++) { + pPrt = &pAC->GIni.GP[i]; + + /* Calculate/Check values for the receive queue */ + Rtv2 = DoCalcAddr(pAC, pPrt, pPrt->PRxQSize, &StartAddr, + &pPrt->PRxQRamStart, &pPrt->PRxQRamEnd); + Rtv |= Rtv2; + + /* Calculate/Check values for the synchronous Tx queue */ + Rtv2 = DoCalcAddr(pAC, pPrt, pPrt->PXSQSize, &StartAddr, + &pPrt->PXsQRamStart, &pPrt->PXsQRamEnd); + Rtv |= Rtv2; + + /* Calculate/Check values for the asynchronous Tx queue */ + Rtv2 = DoCalcAddr(pAC, pPrt, pPrt->PXAQSize, &StartAddr, + &pPrt->PXaQRamStart, &pPrt->PXaQRamEnd); + Rtv |= Rtv2; + + if (Rtv) { + SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_HWI_E013, SKERR_HWI_E013MSG); + return(1); + } + } + + return(0); +} /* SkGeCheckQSize */ + + +#ifdef GENESIS +/****************************************************************************** + * + * SkGeInitMacArb() - Initialize the MAC Arbiter + * + * Description: + * This function initializes the MAC Arbiter. + * It must not be called if there is still an + * initialized or active port. + * + * Returns: + * nothing + */ +static void SkGeInitMacArb( +SK_AC *pAC, /* adapter context */ +SK_IOC IoC) /* IO context */ +{ + /* release local reset */ + SK_OUT16(IoC, B3_MA_TO_CTRL, MA_RST_CLR); + + /* configure timeout values */ + SK_OUT8(IoC, B3_MA_TOINI_RX1, SK_MAC_TO_53); + SK_OUT8(IoC, B3_MA_TOINI_RX2, SK_MAC_TO_53); + SK_OUT8(IoC, B3_MA_TOINI_TX1, SK_MAC_TO_53); + SK_OUT8(IoC, B3_MA_TOINI_TX2, SK_MAC_TO_53); + + SK_OUT8(IoC, B3_MA_RCINI_RX1, 0); + SK_OUT8(IoC, B3_MA_RCINI_RX2, 0); + SK_OUT8(IoC, B3_MA_RCINI_TX1, 0); + SK_OUT8(IoC, B3_MA_RCINI_TX2, 0); + + /* recovery values are needed for XMAC II Rev. B2 only */ + /* Fast Output Enable Mode was intended to use with Rev. B2, but now? */ + + /* + * There is no start or enable button to push, therefore + * the MAC arbiter is configured and enabled now. + */ +} /* SkGeInitMacArb */ + + +/****************************************************************************** + * + * SkGeInitPktArb() - Initialize the Packet Arbiter + * + * Description: + * This function initializes the Packet Arbiter. + * It must not be called if there is still an + * initialized or active port. + * + * Returns: + * nothing + */ +static void SkGeInitPktArb( +SK_AC *pAC, /* adapter context */ +SK_IOC IoC) /* IO context */ +{ + /* release local reset */ + SK_OUT16(IoC, B3_PA_CTRL, PA_RST_CLR); + + /* configure timeout values */ + SK_OUT16(IoC, B3_PA_TOINI_RX1, SK_PKT_TO_MAX); + SK_OUT16(IoC, B3_PA_TOINI_RX2, SK_PKT_TO_MAX); + SK_OUT16(IoC, B3_PA_TOINI_TX1, SK_PKT_TO_MAX); + SK_OUT16(IoC, B3_PA_TOINI_TX2, SK_PKT_TO_MAX); + + /* + * enable timeout timers if jumbo frames not used + * NOTE: the packet arbiter timeout interrupt is needed for + * half duplex hangup workaround + */ + if (pAC->GIni.GIPortUsage != SK_JUMBO_LINK) { + if (pAC->GIni.GIMacsFound == 1) { + SK_OUT16(IoC, B3_PA_CTRL, PA_ENA_TO_TX1); + } + else { + SK_OUT16(IoC, B3_PA_CTRL, PA_ENA_TO_TX1 | PA_ENA_TO_TX2); + } + } +} /* SkGeInitPktArb */ +#endif /* GENESIS */ + + +/****************************************************************************** + * + * SkGeInitMacFifo() - Initialize the MAC FIFOs + * + * Description: + * Initialize all MAC FIFOs of the specified port + * + * Returns: + * nothing + */ +static void SkGeInitMacFifo( +SK_AC *pAC, /* adapter context */ +SK_IOC IoC, /* IO context */ +int Port) /* Port Index (MAC_1 + n) */ +{ + SK_U16 Word; +#ifdef VCPU + SK_U32 DWord; +#endif /* VCPU */ + /* + * For each FIFO: + * - release local reset + * - use default value for MAC FIFO size + * - setup defaults for the control register + * - enable the FIFO + */ + +#ifdef GENESIS + if (pAC->GIni.GIGenesis) { + /* Configure Rx MAC FIFO */ + SK_OUT8(IoC, MR_ADDR(Port, RX_MFF_CTRL2), MFF_RST_CLR); + SK_OUT16(IoC, MR_ADDR(Port, RX_MFF_CTRL1), MFF_RX_CTRL_DEF); + SK_OUT8(IoC, MR_ADDR(Port, RX_MFF_CTRL2), MFF_ENA_OP_MD); + + /* Configure Tx MAC FIFO */ + SK_OUT8(IoC, MR_ADDR(Port, TX_MFF_CTRL2), MFF_RST_CLR); + SK_OUT16(IoC, MR_ADDR(Port, TX_MFF_CTRL1), MFF_TX_CTRL_DEF); + SK_OUT8(IoC, MR_ADDR(Port, TX_MFF_CTRL2), MFF_ENA_OP_MD); + + /* Enable frame flushing if jumbo frames used */ + if (pAC->GIni.GIPortUsage == SK_JUMBO_LINK) { + SK_OUT16(IoC, MR_ADDR(Port, RX_MFF_CTRL1), MFF_ENA_FLUSH); + } + } +#endif /* GENESIS */ + +#ifdef YUKON + if (pAC->GIni.GIYukon) { + /* set Rx GMAC FIFO Flush Mask */ + SK_OUT16(IoC, MR_ADDR(Port, RX_GMF_FL_MSK), (SK_U16)RX_FF_FL_DEF_MSK); + + Word = (SK_U16)GMF_RX_CTRL_DEF; + + /* disable Rx GMAC FIFO Flush for YUKON-Lite Rev. A0 only */ + if (pAC->GIni.GIYukonLite && pAC->GIni.GIChipId == CHIP_ID_YUKON) { + + Word &= ~GMF_RX_F_FL_ON; + } + + /* Configure Rx MAC FIFO */ + SK_OUT8(IoC, MR_ADDR(Port, RX_GMF_CTRL_T), (SK_U8)GMF_RST_CLR); + SK_OUT16(IoC, MR_ADDR(Port, RX_GMF_CTRL_T), Word); + + /* set Rx GMAC FIFO Flush Threshold (default: 0x0a -> 56 bytes) */ + SK_OUT16(IoC, MR_ADDR(Port, RX_GMF_FL_THR), RX_GMF_FL_THR_DEF); + + /* Configure Tx MAC FIFO */ + SK_OUT8(IoC, MR_ADDR(Port, TX_GMF_CTRL_T), (SK_U8)GMF_RST_CLR); + SK_OUT16(IoC, MR_ADDR(Port, TX_GMF_CTRL_T), (SK_U16)GMF_TX_CTRL_DEF); + +#ifdef VCPU + SK_IN32(IoC, MR_ADDR(Port, RX_GMF_AF_THR), &DWord); + SK_IN32(IoC, MR_ADDR(Port, TX_GMF_AE_THR), &DWord); +#endif /* VCPU */ + + /* set Tx GMAC FIFO Almost Empty Threshold */ +/* SK_OUT32(IoC, MR_ADDR(Port, TX_GMF_AE_THR), 0); */ + } +#endif /* YUKON */ + +} /* SkGeInitMacFifo */ + +#ifdef SK_LNK_SYNC_CNT +/****************************************************************************** + * + * SkGeLoadLnkSyncCnt() - Load the Link Sync Counter and starts counting + * + * Description: + * This function starts the Link Sync Counter of the specified + * port and enables the generation of an Link Sync IRQ. + * The Link Sync Counter may be used to detect an active link, + * if autonegotiation is not used. + * + * Note: + * o To ensure receiving the Link Sync Event the LinkSyncCounter + * should be initialized BEFORE clearing the XMAC's reset! + * o Enable IS_LNK_SYNC_M1 and IS_LNK_SYNC_M2 after calling this + * function. + * + * Returns: + * nothing + */ +void SkGeLoadLnkSyncCnt( +SK_AC *pAC, /* adapter context */ +SK_IOC IoC, /* IO context */ +int Port, /* Port Index (MAC_1 + n) */ +SK_U32 CntVal) /* Counter value */ +{ + SK_U32 OrgIMsk; + SK_U32 NewIMsk; + SK_U32 ISrc; + SK_BOOL IrqPend; + + /* stop counter */ + SK_OUT8(IoC, MR_ADDR(Port, LNK_SYNC_CTRL), LED_STOP); + + /* + * ASIC problem: + * Each time starting the Link Sync Counter an IRQ is generated + * by the adapter. See problem report entry from 21.07.98 + * + * Workaround: Disable Link Sync IRQ and clear the unexpeced IRQ + * if no IRQ is already pending. + */ + IrqPend = SK_FALSE; + SK_IN32(IoC, B0_ISRC, &ISrc); + SK_IN32(IoC, B0_IMSK, &OrgIMsk); + if (Port == MAC_1) { + NewIMsk = OrgIMsk & ~IS_LNK_SYNC_M1; + if ((ISrc & IS_LNK_SYNC_M1) != 0) { + IrqPend = SK_TRUE; + } + } + else { + NewIMsk = OrgIMsk & ~IS_LNK_SYNC_M2; + if ((ISrc & IS_LNK_SYNC_M2) != 0) { + IrqPend = SK_TRUE; + } + } + if (!IrqPend) { + SK_OUT32(IoC, B0_IMSK, NewIMsk); + } + + /* load counter */ + SK_OUT32(IoC, MR_ADDR(Port, LNK_SYNC_INI), CntVal); + + /* start counter */ + SK_OUT8(IoC, MR_ADDR(Port, LNK_SYNC_CTRL), LED_START); + + if (!IrqPend) { + /* clear the unexpected IRQ, and restore the interrupt mask */ + SK_OUT8(IoC, MR_ADDR(Port, LNK_SYNC_CTRL), LED_CLR_IRQ); + SK_OUT32(IoC, B0_IMSK, OrgIMsk); + } +} /* SkGeLoadLnkSyncCnt*/ +#endif /* SK_LNK_SYNC_CNT */ + +#if defined(SK_DIAG) || defined(SK_CFG_SYNC) +/****************************************************************************** + * + * SkGeCfgSync() - Configure synchronous bandwidth for this port. + * + * Description: + * This function may be used to configure synchronous bandwidth + * to the specified port. This may be done any time after + * initializing the port. The configuration values are NOT saved + * in the HWAC port structure and will be overwritten any + * time when stopping and starting the port. + * Any values for the synchronous configuration will be ignored + * if the size of the synchronous queue is zero! + * + * The default configuration for the synchronous service is + * TXA_ENA_FSYNC. This means if the size of + * the synchronous queue is unequal zero but no specific + * synchronous bandwidth is configured, the synchronous queue + * will always have the 'unlimited' transmit priority! + * + * This mode will be restored if the synchronous bandwidth is + * deallocated ('IntTime' = 0 and 'LimCount' = 0). + * + * Returns: + * 0: success + * 1: parameter configuration error + * 2: try to configure quality of service although no + * synchronous queue is configured + */ +int SkGeCfgSync( +SK_AC *pAC, /* adapter context */ +SK_IOC IoC, /* IO context */ +int Port, /* Port Index (MAC_1 + n) */ +SK_U32 IntTime, /* Interval Timer Value in units of 8ns */ +SK_U32 LimCount, /* Number of bytes to transfer during IntTime */ +int SyncMode) /* Sync Mode: TXA_ENA_ALLOC | TXA_DIS_ALLOC | 0 */ +{ + int Rtv; + + Rtv = 0; + + /* check the parameters */ + if (LimCount > IntTime || + (LimCount == 0 && IntTime != 0) || + (LimCount != 0 && IntTime == 0)) { + + SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_HWI_E010, SKERR_HWI_E010MSG); + return(1); + } + + if (pAC->GIni.GP[Port].PXSQSize == 0) { + SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_HWI_E009, SKERR_HWI_E009MSG); + return(2); + } + + /* calculate register values */ + IntTime = (IntTime / 2) * pAC->GIni.GIHstClkFact / 100; + LimCount = LimCount / 8; + + if (IntTime > TXA_MAX_VAL || LimCount > TXA_MAX_VAL) { + SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_HWI_E010, SKERR_HWI_E010MSG); + return(1); + } + + /* + * - Enable 'Force Sync' to ensure the synchronous queue + * has the priority while configuring the new values. + * - Also 'disable alloc' to ensure the settings complies + * to the SyncMode parameter. + * - Disable 'Rate Control' to configure the new values. + * - write IntTime and LimCount + * - start 'Rate Control' and disable 'Force Sync' + * if Interval Timer or Limit Counter not zero. + */ + SK_OUT8(IoC, MR_ADDR(Port, TXA_CTRL), + TXA_ENA_FSYNC | TXA_DIS_ALLOC | TXA_STOP_RC); + + SK_OUT32(IoC, MR_ADDR(Port, TXA_ITI_INI), IntTime); + SK_OUT32(IoC, MR_ADDR(Port, TXA_LIM_INI), LimCount); + + SK_OUT8(IoC, MR_ADDR(Port, TXA_CTRL), + (SK_U8)(SyncMode & (TXA_ENA_ALLOC | TXA_DIS_ALLOC))); + + if (IntTime != 0 || LimCount != 0) { + SK_OUT8(IoC, MR_ADDR(Port, TXA_CTRL), TXA_DIS_FSYNC | TXA_START_RC); + } + + return(0); +} /* SkGeCfgSync */ +#endif /* SK_DIAG || SK_CFG_SYNC*/ + + +/****************************************************************************** + * + * DoInitRamQueue() - Initialize the RAM Buffer Address of a single Queue + * + * Desccription: + * If the queue is used, enable and initialize it. + * Make sure the queue is still reset, if it is not used. + * + * Returns: + * nothing + */ +static void DoInitRamQueue( +SK_AC *pAC, /* adapter context */ +SK_IOC IoC, /* IO context */ +int QuIoOffs, /* Queue IO Address Offset */ +SK_U32 QuStartAddr, /* Queue Start Address */ +SK_U32 QuEndAddr, /* Queue End Address */ +int QuType) /* Queue Type (SK_RX_SRAM_Q|SK_RX_BRAM_Q|SK_TX_RAM_Q) */ +{ + SK_U32 RxUpThresVal; + SK_U32 RxLoThresVal; + + if (QuStartAddr != QuEndAddr) { + /* calculate thresholds, assume we have a big Rx queue */ + RxUpThresVal = (QuEndAddr + 1 - QuStartAddr - SK_RB_ULPP) / 8; + RxLoThresVal = (QuEndAddr + 1 - QuStartAddr - SK_RB_LLPP_B)/8; + + /* build HW address format */ + QuStartAddr = QuStartAddr / 8; + QuEndAddr = QuEndAddr / 8; + + /* release local reset */ + SK_OUT8(IoC, RB_ADDR(QuIoOffs, RB_CTRL), RB_RST_CLR); + + /* configure addresses */ + SK_OUT32(IoC, RB_ADDR(QuIoOffs, RB_START), QuStartAddr); + SK_OUT32(IoC, RB_ADDR(QuIoOffs, RB_END), QuEndAddr); + SK_OUT32(IoC, RB_ADDR(QuIoOffs, RB_WP), QuStartAddr); + SK_OUT32(IoC, RB_ADDR(QuIoOffs, RB_RP), QuStartAddr); + + switch (QuType) { + case SK_RX_SRAM_Q: + /* configure threshold for small Rx Queue */ + RxLoThresVal += (SK_RB_LLPP_B - SK_RB_LLPP_S) / 8; + + /* continue with SK_RX_BRAM_Q */ + case SK_RX_BRAM_Q: + /* write threshold for Rx Queue */ + + SK_OUT32(IoC, RB_ADDR(QuIoOffs, RB_RX_UTPP), RxUpThresVal); + SK_OUT32(IoC, RB_ADDR(QuIoOffs, RB_RX_LTPP), RxLoThresVal); + + /* the high priority threshold not used */ + break; + case SK_TX_RAM_Q: + /* + * Do NOT use Store & Forward under normal operation due to + * performance optimization (GENESIS only). + * But if Jumbo Frames are configured (XMAC Tx FIFO is only 4 kB) + * or YUKON is used ((GMAC Tx FIFO is only 1 kB) + * we NEED Store & Forward of the RAM buffer. + */ + if (pAC->GIni.GIPortUsage == SK_JUMBO_LINK || + pAC->GIni.GIYukon) { + /* enable Store & Forward Mode for the Tx Side */ + SK_OUT8(IoC, RB_ADDR(QuIoOffs, RB_CTRL), RB_ENA_STFWD); + } + break; + } + + /* set queue operational */ + SK_OUT8(IoC, RB_ADDR(QuIoOffs, RB_CTRL), RB_ENA_OP_MD); + } + else { + /* ensure the queue is still disabled */ + SK_OUT8(IoC, RB_ADDR(QuIoOffs, RB_CTRL), RB_RST_SET); + } +} /* DoInitRamQueue */ + + +/****************************************************************************** + * + * SkGeInitRamBufs() - Initialize the RAM Buffer Queues + * + * Description: + * Initialize all RAM Buffer Queues of the specified port + * + * Returns: + * nothing + */ +static void SkGeInitRamBufs( +SK_AC *pAC, /* adapter context */ +SK_IOC IoC, /* IO context */ +int Port) /* Port Index (MAC_1 + n) */ +{ + SK_GEPORT *pPrt; + int RxQType; + + pPrt = &pAC->GIni.GP[Port]; + + if (pPrt->PRxQSize == SK_MIN_RXQ_SIZE) { + RxQType = SK_RX_SRAM_Q; /* small Rx Queue */ + } + else { + RxQType = SK_RX_BRAM_Q; /* big Rx Queue */ + } + + DoInitRamQueue(pAC, IoC, pPrt->PRxQOff, pPrt->PRxQRamStart, + pPrt->PRxQRamEnd, RxQType); + + DoInitRamQueue(pAC, IoC, pPrt->PXsQOff, pPrt->PXsQRamStart, + pPrt->PXsQRamEnd, SK_TX_RAM_Q); + + DoInitRamQueue(pAC, IoC, pPrt->PXaQOff, pPrt->PXaQRamStart, + pPrt->PXaQRamEnd, SK_TX_RAM_Q); + +} /* SkGeInitRamBufs */ + + +/****************************************************************************** + * + * SkGeInitRamIface() - Initialize the RAM Interface + * + * Description: + * This function initializes the Adapters RAM Interface. + * + * Note: + * This function is used in the diagnostics. + * + * Returns: + * nothing + */ +static void SkGeInitRamIface( +SK_AC *pAC, /* adapter context */ +SK_IOC IoC) /* IO context */ +{ + /* release local reset */ + SK_OUT16(IoC, B3_RI_CTRL, RI_RST_CLR); + + /* configure timeout values */ + SK_OUT8(IoC, B3_RI_WTO_R1, SK_RI_TO_53); + SK_OUT8(IoC, B3_RI_WTO_XA1, SK_RI_TO_53); + SK_OUT8(IoC, B3_RI_WTO_XS1, SK_RI_TO_53); + SK_OUT8(IoC, B3_RI_RTO_R1, SK_RI_TO_53); + SK_OUT8(IoC, B3_RI_RTO_XA1, SK_RI_TO_53); + SK_OUT8(IoC, B3_RI_RTO_XS1, SK_RI_TO_53); + SK_OUT8(IoC, B3_RI_WTO_R2, SK_RI_TO_53); + SK_OUT8(IoC, B3_RI_WTO_XA2, SK_RI_TO_53); + SK_OUT8(IoC, B3_RI_WTO_XS2, SK_RI_TO_53); + SK_OUT8(IoC, B3_RI_RTO_R2, SK_RI_TO_53); + SK_OUT8(IoC, B3_RI_RTO_XA2, SK_RI_TO_53); + SK_OUT8(IoC, B3_RI_RTO_XS2, SK_RI_TO_53); + +} /* SkGeInitRamIface */ + + +/****************************************************************************** + * + * SkGeInitBmu() - Initialize the BMU state machines + * + * Description: + * Initialize all BMU state machines of the specified port + * + * Returns: + * nothing + */ +static void SkGeInitBmu( +SK_AC *pAC, /* adapter context */ +SK_IOC IoC, /* IO context */ +int Port) /* Port Index (MAC_1 + n) */ +{ + SK_GEPORT *pPrt; + SK_U32 RxWm; + SK_U32 TxWm; + + pPrt = &pAC->GIni.GP[Port]; + + RxWm = SK_BMU_RX_WM; + TxWm = SK_BMU_TX_WM; + + if (!pAC->GIni.GIPciSlot64 && !pAC->GIni.GIPciClock66) { + /* for better performance */ + RxWm /= 2; + TxWm /= 2; + } + + /* Rx Queue: Release all local resets and set the watermark */ + SK_OUT32(IoC, Q_ADDR(pPrt->PRxQOff, Q_CSR), CSR_CLR_RESET); + SK_OUT32(IoC, Q_ADDR(pPrt->PRxQOff, Q_F), RxWm); + + /* + * Tx Queue: Release all local resets if the queue is used ! + * set watermark + */ + if (pPrt->PXSQSize != 0) { + SK_OUT32(IoC, Q_ADDR(pPrt->PXsQOff, Q_CSR), CSR_CLR_RESET); + SK_OUT32(IoC, Q_ADDR(pPrt->PXsQOff, Q_F), TxWm); + } + + if (pPrt->PXAQSize != 0) { + SK_OUT32(IoC, Q_ADDR(pPrt->PXaQOff, Q_CSR), CSR_CLR_RESET); + SK_OUT32(IoC, Q_ADDR(pPrt->PXaQOff, Q_F), TxWm); + } + /* + * Do NOT enable the descriptor poll timers here, because + * the descriptor addresses are not specified yet. + */ +} /* SkGeInitBmu */ + + +/****************************************************************************** + * + * TestStopBit() - Test the stop bit of the queue + * + * Description: + * Stopping a queue is not as simple as it seems to be. + * If descriptor polling is enabled, it may happen + * that RX/TX stop is done and SV idle is NOT set. + * In this case we have to issue another stop command. + * + * Returns: + * The queues control status register + */ +static SK_U32 TestStopBit( +SK_AC *pAC, /* Adapter Context */ +SK_IOC IoC, /* IO Context */ +int QuIoOffs) /* Queue IO Address Offset */ +{ + SK_U32 QuCsr; /* CSR contents */ + + SK_IN32(IoC, Q_ADDR(QuIoOffs, Q_CSR), &QuCsr); + + if ((QuCsr & (CSR_STOP | CSR_SV_IDLE)) == 0) { + /* Stop Descriptor overridden by start command */ + SK_OUT32(IoC, Q_ADDR(QuIoOffs, Q_CSR), CSR_STOP); + + SK_IN32(IoC, Q_ADDR(QuIoOffs, Q_CSR), &QuCsr); + } + + return(QuCsr); +} /* TestStopBit */ + + +/****************************************************************************** + * + * SkGeStopPort() - Stop the Rx/Tx activity of the port 'Port'. + * + * Description: + * After calling this function the descriptor rings and Rx and Tx + * queues of this port may be reconfigured. + * + * It is possible to stop the receive and transmit path separate or + * both together. + * + * Dir = SK_STOP_TX Stops the transmit path only and resets the MAC. + * The receive queue is still active and + * the pending Rx frames may be still transferred + * into the RxD. + * SK_STOP_RX Stop the receive path. The tansmit path + * has to be stopped once before. + * SK_STOP_ALL SK_STOP_TX + SK_STOP_RX + * + * RstMode = SK_SOFT_RST Resets the MAC. The PHY is still alive. + * SK_HARD_RST Resets the MAC and the PHY. + * + * Example: + * 1) A Link Down event was signaled for a port. Therefore the activity + * of this port should be stopped and a hardware reset should be issued + * to enable the workaround of XMAC Errata #2. But the received frames + * should not be discarded. + * ... + * SkGeStopPort(pAC, IoC, Port, SK_STOP_TX, SK_HARD_RST); + * (transfer all pending Rx frames) + * SkGeStopPort(pAC, IoC, Port, SK_STOP_RX, SK_HARD_RST); + * ... + * + * 2) An event was issued which request the driver to switch + * the 'virtual active' link to an other already active port + * as soon as possible. The frames in the receive queue of this + * port may be lost. But the PHY must not be reset during this + * event. + * ... + * SkGeStopPort(pAC, IoC, Port, SK_STOP_ALL, SK_SOFT_RST); + * ... + * + * Extended Description: + * If SK_STOP_TX is set, + * o disable the MAC's receive and transmitter to prevent + * from sending incomplete frames + * o stop the port's transmit queues before terminating the + * BMUs to prevent from performing incomplete PCI cycles + * on the PCI bus + * - The network Rx and Tx activity and PCI Tx transfer is + * disabled now. + * o reset the MAC depending on the RstMode + * o Stop Interval Timer and Limit Counter of Tx Arbiter, + * also disable Force Sync bit and Enable Alloc bit. + * o perform a local reset of the port's Tx path + * - reset the PCI FIFO of the async Tx queue + * - reset the PCI FIFO of the sync Tx queue + * - reset the RAM Buffer async Tx queue + * - reset the RAM Buffer sync Tx queue + * - reset the MAC Tx FIFO + * o switch Link and Tx LED off, stop the LED counters + * + * If SK_STOP_RX is set, + * o stop the port's receive queue + * - The path data transfer activity is fully stopped now. + * o perform a local reset of the port's Rx path + * - reset the PCI FIFO of the Rx queue + * - reset the RAM Buffer receive queue + * - reset the MAC Rx FIFO + * o switch Rx LED off, stop the LED counter + * + * If all ports are stopped, + * o reset the RAM Interface. + * + * Notes: + * o This function may be called during the driver states RESET_PORT and + * SWITCH_PORT. + */ +void SkGeStopPort( +SK_AC *pAC, /* adapter context */ +SK_IOC IoC, /* I/O context */ +int Port, /* port to stop (MAC_1 + n) */ +int Dir, /* Direction to Stop (SK_STOP_RX, SK_STOP_TX, SK_STOP_ALL) */ +int RstMode)/* Reset Mode (SK_SOFT_RST, SK_HARD_RST) */ +{ +#ifndef SK_DIAG + SK_EVPARA Para; +#endif /* !SK_DIAG */ + SK_GEPORT *pPrt; + SK_U32 DWord; + SK_U32 XsCsr; + SK_U32 XaCsr; + SK_U64 ToutStart; + int i; + int ToutCnt; + + pPrt = &pAC->GIni.GP[Port]; + + if ((Dir & SK_STOP_TX) != 0) { + /* disable receiver and transmitter */ + SkMacRxTxDisable(pAC, IoC, Port); + + /* stop both transmit queues */ + /* + * If the BMU is in the reset state CSR_STOP will terminate + * immediately. + */ + SK_OUT32(IoC, Q_ADDR(pPrt->PXsQOff, Q_CSR), CSR_STOP); + SK_OUT32(IoC, Q_ADDR(pPrt->PXaQOff, Q_CSR), CSR_STOP); + + ToutStart = SkOsGetTime(pAC); + ToutCnt = 0; + do { + /* + * Clear packet arbiter timeout to make sure + * this loop will terminate. + */ + SK_OUT16(IoC, B3_PA_CTRL, (SK_U16)((Port == MAC_1) ? + PA_CLR_TO_TX1 : PA_CLR_TO_TX2)); + + /* + * If the transfer stucks at the MAC the STOP command will not + * terminate if we don't flush the XMAC's transmit FIFO ! + */ + SkMacFlushTxFifo(pAC, IoC, Port); + + XsCsr = TestStopBit(pAC, IoC, pPrt->PXsQOff); + XaCsr = TestStopBit(pAC, IoC, pPrt->PXaQOff); + + if (SkOsGetTime(pAC) - ToutStart > (SK_TICKS_PER_SEC / 18)) { + /* + * Timeout of 1/18 second reached. + * This needs to be checked at 1/18 sec only. + */ + ToutCnt++; + if (ToutCnt > 1) { + /* Might be a problem when the driver event handler + * calls StopPort again. XXX. + */ + + /* Fatal Error, Loop aborted */ + SK_ERR_LOG(pAC, SK_ERRCL_HW, SKERR_HWI_E018, + SKERR_HWI_E018MSG); +#ifndef SK_DIAG + Para.Para64 = Port; + SkEventQueue(pAC, SKGE_DRV, SK_DRV_PORT_FAIL, Para); +#endif /* !SK_DIAG */ + return; + } + /* + * Cache incoherency workaround: Assume a start command + * has been lost while sending the frame. + */ + ToutStart = SkOsGetTime(pAC); + + if ((XsCsr & CSR_STOP) != 0) { + SK_OUT32(IoC, Q_ADDR(pPrt->PXsQOff, Q_CSR), CSR_START); + } + if ((XaCsr & CSR_STOP) != 0) { + SK_OUT32(IoC, Q_ADDR(pPrt->PXaQOff, Q_CSR), CSR_START); + } + } + + /* + * Because of the ASIC problem report entry from 21.08.1998 it is + * required to wait until CSR_STOP is reset and CSR_SV_IDLE is set. + */ + } while ((XsCsr & (CSR_STOP | CSR_SV_IDLE)) != CSR_SV_IDLE || + (XaCsr & (CSR_STOP | CSR_SV_IDLE)) != CSR_SV_IDLE); + + /* Reset the MAC depending on the RstMode */ + if (RstMode == SK_SOFT_RST) { + SkMacSoftRst(pAC, IoC, Port); + } + else { + SkMacHardRst(pAC, IoC, Port); + } + + /* Disable Force Sync bit and Enable Alloc bit */ + SK_OUT8(IoC, MR_ADDR(Port, TXA_CTRL), + TXA_DIS_FSYNC | TXA_DIS_ALLOC | TXA_STOP_RC); + + /* Stop Interval Timer and Limit Counter of Tx Arbiter */ + SK_OUT32(IoC, MR_ADDR(Port, TXA_ITI_INI), 0L); + SK_OUT32(IoC, MR_ADDR(Port, TXA_LIM_INI), 0L); + + /* Perform a local reset of the port's Tx path */ + + /* Reset the PCI FIFO of the async Tx queue */ + SK_OUT32(IoC, Q_ADDR(pPrt->PXaQOff, Q_CSR), CSR_SET_RESET); + /* Reset the PCI FIFO of the sync Tx queue */ + SK_OUT32(IoC, Q_ADDR(pPrt->PXsQOff, Q_CSR), CSR_SET_RESET); + /* Reset the RAM Buffer async Tx queue */ + SK_OUT8(IoC, RB_ADDR(pPrt->PXaQOff, RB_CTRL), RB_RST_SET); + /* Reset the RAM Buffer sync Tx queue */ + SK_OUT8(IoC, RB_ADDR(pPrt->PXsQOff, RB_CTRL), RB_RST_SET); + + /* Reset Tx MAC FIFO */ +#ifdef GENESIS + if (pAC->GIni.GIGenesis) { + /* Note: MFF_RST_SET does NOT reset the XMAC ! */ + SK_OUT8(IoC, MR_ADDR(Port, TX_MFF_CTRL2), MFF_RST_SET); + + /* switch Link and Tx LED off, stop the LED counters */ + /* Link LED is switched off by the RLMT and the Diag itself */ + SkGeXmitLED(pAC, IoC, MR_ADDR(Port, TX_LED_INI), SK_LED_DIS); + } +#endif /* GENESIS */ + +#ifdef YUKON + if (pAC->GIni.GIYukon) { + /* Reset TX MAC FIFO */ + SK_OUT8(IoC, MR_ADDR(Port, TX_GMF_CTRL_T), (SK_U8)GMF_RST_SET); + } +#endif /* YUKON */ + } + + if ((Dir & SK_STOP_RX) != 0) { + /* + * The RX Stop Command will not terminate if no buffers + * are queued in the RxD ring. But it will always reach + * the Idle state. Therefore we can use this feature to + * stop the transfer of received packets. + */ + /* stop the port's receive queue */ + SK_OUT32(IoC, Q_ADDR(pPrt->PRxQOff, Q_CSR), CSR_STOP); + + i = 100; + do { + /* + * Clear packet arbiter timeout to make sure + * this loop will terminate + */ + SK_OUT16(IoC, B3_PA_CTRL, (SK_U16)((Port == MAC_1) ? + PA_CLR_TO_RX1 : PA_CLR_TO_RX2)); + + DWord = TestStopBit(pAC, IoC, pPrt->PRxQOff); + + /* timeout if i==0 (bug fix for #10748) */ + if (--i == 0) { + SK_ERR_LOG(pAC, SK_ERRCL_HW, SKERR_HWI_E024, + SKERR_HWI_E024MSG); + break; + } + /* + * because of the ASIC problem report entry from 21.08.98 + * it is required to wait until CSR_STOP is reset and + * CSR_SV_IDLE is set. + */ + } while ((DWord & (CSR_STOP | CSR_SV_IDLE)) != CSR_SV_IDLE); + + /* The path data transfer activity is fully stopped now */ + + /* Perform a local reset of the port's Rx path */ + + /* Reset the PCI FIFO of the Rx queue */ + SK_OUT32(IoC, Q_ADDR(pPrt->PRxQOff, Q_CSR), CSR_SET_RESET); + /* Reset the RAM Buffer receive queue */ + SK_OUT8(IoC, RB_ADDR(pPrt->PRxQOff, RB_CTRL), RB_RST_SET); + + /* Reset Rx MAC FIFO */ +#ifdef GENESIS + if (pAC->GIni.GIGenesis) { + + SK_OUT8(IoC, MR_ADDR(Port, RX_MFF_CTRL2), MFF_RST_SET); + + /* switch Rx LED off, stop the LED counter */ + SkGeXmitLED(pAC, IoC, MR_ADDR(Port, RX_LED_INI), SK_LED_DIS); + } +#endif /* GENESIS */ + +#ifdef YUKON + if (pAC->GIni.GIYukon) { + /* Reset Rx MAC FIFO */ + SK_OUT8(IoC, MR_ADDR(Port, RX_GMF_CTRL_T), (SK_U8)GMF_RST_SET); + } +#endif /* YUKON */ + } +} /* SkGeStopPort */ + + +/****************************************************************************** + * + * SkGeInit0() - Level 0 Initialization + * + * Description: + * - Initialize the BMU address offsets + * + * Returns: + * nothing + */ +static void SkGeInit0( +SK_AC *pAC, /* adapter context */ +SK_IOC IoC) /* IO context */ +{ + int i; + SK_GEPORT *pPrt; + + for (i = 0; i < SK_MAX_MACS; i++) { + pPrt = &pAC->GIni.GP[i]; + + pPrt->PState = SK_PRT_RESET; + pPrt->PRxQOff = QOffTab[i].RxQOff; + pPrt->PXsQOff = QOffTab[i].XsQOff; + pPrt->PXaQOff = QOffTab[i].XaQOff; + pPrt->PCheckPar = SK_FALSE; + pPrt->PIsave = 0; + pPrt->PPrevShorts = 0; + pPrt->PLinkResCt = 0; + pPrt->PAutoNegTOCt = 0; + pPrt->PPrevRx = 0; + pPrt->PPrevFcs = 0; + pPrt->PRxLim = SK_DEF_RX_WA_LIM; + pPrt->PLinkMode = (SK_U8)SK_LMODE_AUTOFULL; + pPrt->PLinkSpeedCap = (SK_U8)SK_LSPEED_CAP_1000MBPS; + pPrt->PLinkSpeed = (SK_U8)SK_LSPEED_1000MBPS; + pPrt->PLinkSpeedUsed = (SK_U8)SK_LSPEED_STAT_UNKNOWN; + pPrt->PLinkModeConf = (SK_U8)SK_LMODE_AUTOSENSE; + pPrt->PFlowCtrlMode = (SK_U8)SK_FLOW_MODE_SYM_OR_REM; + pPrt->PLinkCap = (SK_U8)(SK_LMODE_CAP_HALF | SK_LMODE_CAP_FULL | + SK_LMODE_CAP_AUTOHALF | SK_LMODE_CAP_AUTOFULL); + pPrt->PLinkModeStatus = (SK_U8)SK_LMODE_STAT_UNKNOWN; + pPrt->PFlowCtrlCap = (SK_U8)SK_FLOW_MODE_SYM_OR_REM; + pPrt->PFlowCtrlStatus = (SK_U8)SK_FLOW_STAT_NONE; + pPrt->PMSCap = 0; + pPrt->PMSMode = (SK_U8)SK_MS_MODE_AUTO; + pPrt->PMSStatus = (SK_U8)SK_MS_STAT_UNSET; + pPrt->PLipaAutoNeg = (SK_U8)SK_LIPA_UNKNOWN; + pPrt->PAutoNegFail = SK_FALSE; + pPrt->PHWLinkUp = SK_FALSE; + pPrt->PLinkBroken = SK_TRUE; /* See WA code */ + pPrt->PPhyPowerState = PHY_PM_OPERATIONAL_MODE; + pPrt->PMacColThres = TX_COL_DEF; + pPrt->PMacJamLen = TX_JAM_LEN_DEF; + pPrt->PMacJamIpgVal = TX_JAM_IPG_DEF; + pPrt->PMacJamIpgData = TX_IPG_JAM_DEF; + pPrt->PMacIpgData = IPG_DATA_DEF; + pPrt->PMacLimit4 = SK_FALSE; + } + + pAC->GIni.GIPortUsage = SK_RED_LINK; + pAC->GIni.GILedBlinkCtrl = (SK_U16)OemConfig.Value; + pAC->GIni.GIValIrqMask = IS_ALL_MSK; + +} /* SkGeInit0*/ + + +/****************************************************************************** + * + * SkGeInit1() - Level 1 Initialization + * + * Description: + * o Do a software reset. + * o Clear all reset bits. + * o Verify that the detected hardware is present. + * Return an error if not. + * o Get the hardware configuration + * + Read the number of MACs/Ports. + * + Read the RAM size. + * + Read the PCI Revision Id. + * + Find out the adapters host clock speed + * + Read and check the PHY type + * + * Returns: + * 0: success + * 5: Unexpected PHY type detected + * 6: HW self test failed + */ +static int SkGeInit1( +SK_AC *pAC, /* adapter context */ +SK_IOC IoC) /* IO context */ +{ + SK_U8 Byte; + SK_U16 Word; + SK_U16 CtrlStat; + SK_U32 DWord; + int RetVal; + int i; + + RetVal = 0; + + /* save CLK_RUN bits (YUKON-Lite) */ + SK_IN16(IoC, B0_CTST, &CtrlStat); + + /* do the SW-reset */ + SK_OUT8(IoC, B0_CTST, CS_RST_SET); + + /* release the SW-reset */ + SK_OUT8(IoC, B0_CTST, CS_RST_CLR); + + /* reset all error bits in the PCI STATUS register */ + /* + * Note: PCI Cfg cycles cannot be used, because they are not + * available on some platforms after 'boot time'. + */ + SK_IN16(IoC, PCI_C(PCI_STATUS), &Word); + + SK_OUT8(IoC, B2_TST_CTRL1, TST_CFG_WRITE_ON); + SK_OUT16(IoC, PCI_C(PCI_STATUS), (SK_U16)(Word | PCI_ERRBITS)); + SK_OUT8(IoC, B2_TST_CTRL1, TST_CFG_WRITE_OFF); + + /* release Master Reset */ + SK_OUT8(IoC, B0_CTST, CS_MRST_CLR); + +#ifdef CLK_RUN + CtrlStat |= CS_CLK_RUN_ENA; +#endif /* CLK_RUN */ + + /* restore CLK_RUN bits */ + SK_OUT16(IoC, B0_CTST, (SK_U16)(CtrlStat & + (CS_CLK_RUN_HOT | CS_CLK_RUN_RST | CS_CLK_RUN_ENA))); + + /* read Chip Identification Number */ + SK_IN8(IoC, B2_CHIP_ID, &Byte); + pAC->GIni.GIChipId = Byte; + + /* read number of MACs */ + SK_IN8(IoC, B2_MAC_CFG, &Byte); + pAC->GIni.GIMacsFound = (Byte & CFG_SNG_MAC) ? 1 : 2; + + /* get Chip Revision Number */ + pAC->GIni.GIChipRev = (SK_U8)((Byte & CFG_CHIP_R_MSK) >> 4); + + /* get diff. PCI parameters */ + SK_IN16(IoC, B0_CTST, &CtrlStat); + + /* read the adapters RAM size */ + SK_IN8(IoC, B2_E_0, &Byte); + + pAC->GIni.GIGenesis = SK_FALSE; + pAC->GIni.GIYukon = SK_FALSE; + pAC->GIni.GIYukonLite = SK_FALSE; + +#ifdef GENESIS + if (pAC->GIni.GIChipId == CHIP_ID_GENESIS) { + + pAC->GIni.GIGenesis = SK_TRUE; + + if (Byte == (SK_U8)3) { + /* special case: 4 x 64k x 36, offset = 0x80000 */ + pAC->GIni.GIRamSize = 1024; + pAC->GIni.GIRamOffs = (SK_U32)512 * 1024; + } + else { + pAC->GIni.GIRamSize = (int)Byte * 512; + pAC->GIni.GIRamOffs = 0; + } + /* all GE adapters work with 53.125 MHz host clock */ + pAC->GIni.GIHstClkFact = SK_FACT_53; + + /* set Descr. Poll Timer Init Value to 250 ms */ + pAC->GIni.GIPollTimerVal = + SK_DPOLL_DEF * (SK_U32)pAC->GIni.GIHstClkFact / 100; + } +#endif /* GENESIS */ + +#ifdef YUKON + if (pAC->GIni.GIChipId != CHIP_ID_GENESIS) { + + pAC->GIni.GIYukon = SK_TRUE; + + pAC->GIni.GIRamSize = (Byte == (SK_U8)0) ? 128 : (int)Byte * 4; + + pAC->GIni.GIRamOffs = 0; + + /* WA for chip Rev. A */ + pAC->GIni.GIWolOffs = (pAC->GIni.GIChipId == CHIP_ID_YUKON && + pAC->GIni.GIChipRev == 0) ? WOL_REG_OFFS : 0; + + /* get PM Capabilities of PCI config space */ + SK_IN16(IoC, PCI_C(PCI_PM_CAP_REG), &Word); + + /* check if VAUX is available */ + if (((CtrlStat & CS_VAUX_AVAIL) != 0) && + /* check also if PME from D3cold is set */ + ((Word & PCI_PME_D3C_SUP) != 0)) { + /* set entry in GE init struct */ + pAC->GIni.GIVauxAvail = SK_TRUE; + } + + if (pAC->GIni.GIChipId == CHIP_ID_YUKON_LITE) { + /* this is Rev. A1 */ + pAC->GIni.GIYukonLite = SK_TRUE; + } + else { + /* save Flash-Address Register */ + SK_IN32(IoC, B2_FAR, &DWord); + + /* test Flash-Address Register */ + SK_OUT8(IoC, B2_FAR + 3, 0xff); + SK_IN8(IoC, B2_FAR + 3, &Byte); + + if (Byte != 0) { + /* this is Rev. A0 */ + pAC->GIni.GIYukonLite = SK_TRUE; + + /* restore Flash-Address Register */ + SK_OUT32(IoC, B2_FAR, DWord); + } + } + + /* switch power to VCC (WA for VAUX problem) */ + SK_OUT8(IoC, B0_POWER_CTRL, (SK_U8)(PC_VAUX_ENA | PC_VCC_ENA | + PC_VAUX_OFF | PC_VCC_ON)); + + /* read the Interrupt source */ + SK_IN32(IoC, B0_ISRC, &DWord); + + if ((DWord & IS_HW_ERR) != 0) { + /* read the HW Error Interrupt source */ + SK_IN32(IoC, B0_HWE_ISRC, &DWord); + + if ((DWord & IS_IRQ_SENSOR) != 0) { + /* disable HW Error IRQ */ + pAC->GIni.GIValIrqMask &= ~IS_HW_ERR; + } + } + + for (i = 0; i < pAC->GIni.GIMacsFound; i++) { + /* set GMAC Link Control reset */ + SK_OUT16(IoC, MR_ADDR(i, GMAC_LINK_CTRL), GMLC_RST_SET); + + /* clear GMAC Link Control reset */ + SK_OUT16(IoC, MR_ADDR(i, GMAC_LINK_CTRL), GMLC_RST_CLR); + } + /* all YU chips work with 78.125 MHz host clock */ + pAC->GIni.GIHstClkFact = SK_FACT_78; + + pAC->GIni.GIPollTimerVal = SK_DPOLL_MAX; /* 215 ms */ + } +#endif /* YUKON */ + + /* check if 64-bit PCI Slot is present */ + pAC->GIni.GIPciSlot64 = (SK_BOOL)((CtrlStat & CS_BUS_SLOT_SZ) != 0); + + /* check if 66 MHz PCI Clock is active */ + pAC->GIni.GIPciClock66 = (SK_BOOL)((CtrlStat & CS_BUS_CLOCK) != 0); + + /* read PCI HW Revision Id. */ + SK_IN8(IoC, PCI_C(PCI_REV_ID), &Byte); + pAC->GIni.GIPciHwRev = Byte; + + /* read the PMD type */ + SK_IN8(IoC, B2_PMD_TYP, &Byte); + pAC->GIni.GICopperType = (SK_U8)(Byte == 'T'); + + /* read the PHY type */ + SK_IN8(IoC, B2_E_1, &Byte); + + Byte &= 0x0f; /* the PHY type is stored in the lower nibble */ + for (i = 0; i < pAC->GIni.GIMacsFound; i++) { + +#ifdef GENESIS + if (pAC->GIni.GIGenesis) { + switch (Byte) { + case SK_PHY_XMAC: + pAC->GIni.GP[i].PhyAddr = PHY_ADDR_XMAC; + break; + case SK_PHY_BCOM: + pAC->GIni.GP[i].PhyAddr = PHY_ADDR_BCOM; + pAC->GIni.GP[i].PMSCap = (SK_U8)(SK_MS_CAP_AUTO | + SK_MS_CAP_MASTER | SK_MS_CAP_SLAVE); + break; +#ifdef OTHER_PHY + case SK_PHY_LONE: + pAC->GIni.GP[i].PhyAddr = PHY_ADDR_LONE; + break; + case SK_PHY_NAT: + pAC->GIni.GP[i].PhyAddr = PHY_ADDR_NAT; + break; +#endif /* OTHER_PHY */ + default: + /* ERROR: unexpected PHY type detected */ + RetVal = 5; + break; + } + } +#endif /* GENESIS */ + +#ifdef YUKON + if (pAC->GIni.GIYukon) { + + if (Byte < (SK_U8)SK_PHY_MARV_COPPER) { + /* if this field is not initialized */ + Byte = (SK_U8)SK_PHY_MARV_COPPER; + + pAC->GIni.GICopperType = SK_TRUE; + } + + pAC->GIni.GP[i].PhyAddr = PHY_ADDR_MARV; + + if (pAC->GIni.GICopperType) { + + pAC->GIni.GP[i].PLinkSpeedCap = (SK_U8)(SK_LSPEED_CAP_AUTO | + SK_LSPEED_CAP_10MBPS | SK_LSPEED_CAP_100MBPS | + SK_LSPEED_CAP_1000MBPS); + + pAC->GIni.GP[i].PLinkSpeed = (SK_U8)SK_LSPEED_AUTO; + + pAC->GIni.GP[i].PMSCap = (SK_U8)(SK_MS_CAP_AUTO | + SK_MS_CAP_MASTER | SK_MS_CAP_SLAVE); + } + else { + Byte = (SK_U8)SK_PHY_MARV_FIBER; + } + } +#endif /* YUKON */ + + pAC->GIni.GP[i].PhyType = (int)Byte; + + SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_INIT, + ("PHY type: %d PHY addr: %04x\n", Byte, + pAC->GIni.GP[i].PhyAddr)); + } + + /* get MAC Type & set function pointers dependent on */ +#ifdef GENESIS + if (pAC->GIni.GIGenesis) { + + pAC->GIni.GIMacType = SK_MAC_XMAC; + + pAC->GIni.GIFunc.pFnMacUpdateStats = SkXmUpdateStats; + pAC->GIni.GIFunc.pFnMacStatistic = SkXmMacStatistic; + pAC->GIni.GIFunc.pFnMacResetCounter = SkXmResetCounter; + pAC->GIni.GIFunc.pFnMacOverflow = SkXmOverflowStatus; + } +#endif /* GENESIS */ + +#ifdef YUKON + if (pAC->GIni.GIYukon) { + + pAC->GIni.GIMacType = SK_MAC_GMAC; + + pAC->GIni.GIFunc.pFnMacUpdateStats = SkGmUpdateStats; + pAC->GIni.GIFunc.pFnMacStatistic = SkGmMacStatistic; + pAC->GIni.GIFunc.pFnMacResetCounter = SkGmResetCounter; + pAC->GIni.GIFunc.pFnMacOverflow = SkGmOverflowStatus; + +#ifdef SPECIAL_HANDLING + if (pAC->GIni.GIChipId == CHIP_ID_YUKON) { + /* check HW self test result */ + SK_IN8(IoC, B2_E_3, &Byte); + if (Byte & B2_E3_RES_MASK) { + RetVal = 6; + } + } +#endif + } +#endif /* YUKON */ + + return(RetVal); +} /* SkGeInit1 */ + + +/****************************************************************************** + * + * SkGeInit2() - Level 2 Initialization + * + * Description: + * - start the Blink Source Counter + * - start the Descriptor Poll Timer + * - configure the MAC-Arbiter + * - configure the Packet-Arbiter + * - enable the Tx Arbiters + * - enable the RAM Interface Arbiter + * + * Returns: + * nothing + */ +static void SkGeInit2( +SK_AC *pAC, /* adapter context */ +SK_IOC IoC) /* IO context */ +{ +#ifdef GENESIS + SK_U32 DWord; +#endif /* GENESIS */ + int i; + + /* start the Descriptor Poll Timer */ + if (pAC->GIni.GIPollTimerVal != 0) { + if (pAC->GIni.GIPollTimerVal > SK_DPOLL_MAX) { + pAC->GIni.GIPollTimerVal = SK_DPOLL_MAX; + + SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_HWI_E017, SKERR_HWI_E017MSG); + } + SK_OUT32(IoC, B28_DPT_INI, pAC->GIni.GIPollTimerVal); + SK_OUT8(IoC, B28_DPT_CTRL, DPT_START); + } + +#ifdef GENESIS + if (pAC->GIni.GIGenesis) { + /* start the Blink Source Counter */ + DWord = SK_BLK_DUR * (SK_U32)pAC->GIni.GIHstClkFact / 100; + + SK_OUT32(IoC, B2_BSC_INI, DWord); + SK_OUT8(IoC, B2_BSC_CTRL, BSC_START); + + /* + * Configure the MAC Arbiter and the Packet Arbiter. + * They will be started once and never be stopped. + */ + SkGeInitMacArb(pAC, IoC); + + SkGeInitPktArb(pAC, IoC); + } +#endif /* GENESIS */ + +#ifdef YUKON + if (pAC->GIni.GIYukon) { + /* start Time Stamp Timer */ + SK_OUT8(IoC, GMAC_TI_ST_CTRL, (SK_U8)GMT_ST_START); + } +#endif /* YUKON */ + + /* enable the Tx Arbiters */ + for (i = 0; i < pAC->GIni.GIMacsFound; i++) { + SK_OUT8(IoC, MR_ADDR(i, TXA_CTRL), TXA_ENA_ARB); + } + + /* enable the RAM Interface Arbiter */ + SkGeInitRamIface(pAC, IoC); + +} /* SkGeInit2 */ + +/****************************************************************************** + * + * SkGeInit() - Initialize the GE Adapter with the specified level. + * + * Description: + * Level 0: Initialize the Module structures. + * Level 1: Generic Hardware Initialization. The IOP/MemBase pointer has + * to be set before calling this level. + * + * o Do a software reset. + * o Clear all reset bits. + * o Verify that the detected hardware is present. + * Return an error if not. + * o Get the hardware configuration + * + Set GIMacsFound with the number of MACs. + * + Store the RAM size in GIRamSize. + * + Save the PCI Revision ID in GIPciHwRev. + * o return an error + * if Number of MACs > SK_MAX_MACS + * + * After returning from Level 0 the adapter + * may be accessed with IO operations. + * + * Level 2: start the Blink Source Counter + * + * Returns: + * 0: success + * 1: Number of MACs exceeds SK_MAX_MACS (after level 1) + * 2: Adapter not present or not accessible + * 3: Illegal initialization level + * 4: Initialization Level 1 Call missing + * 5: Unexpected PHY type detected + * 6: HW self test failed + */ +int SkGeInit( +SK_AC *pAC, /* adapter context */ +SK_IOC IoC, /* IO context */ +int Level) /* initialization level */ +{ + int RetVal; /* return value */ + SK_U32 DWord; + + RetVal = 0; + SK_DBG_MSG(pAC, SK_DBGMOD_HWM, SK_DBGCAT_INIT, + ("SkGeInit(Level %d)\n", Level)); + + switch (Level) { + case SK_INIT_DATA: + /* Initialization Level 0 */ + SkGeInit0(pAC, IoC); + pAC->GIni.GILevel = SK_INIT_DATA; + break; + + case SK_INIT_IO: + /* Initialization Level 1 */ + RetVal = SkGeInit1(pAC, IoC); + if (RetVal != 0) { + break; + } + + /* check if the adapter seems to be accessible */ + SK_OUT32(IoC, B2_IRQM_INI, SK_TEST_VAL); + SK_IN32(IoC, B2_IRQM_INI, &DWord); + SK_OUT32(IoC, B2_IRQM_INI, 0L); + + if (DWord != SK_TEST_VAL) { + RetVal = 2; + break; + } + + /* check if the number of GIMacsFound matches SK_MAX_MACS */ + if (pAC->GIni.GIMacsFound > SK_MAX_MACS) { + RetVal = 1; + break; + } + + /* Level 1 successfully passed */ + pAC->GIni.GILevel = SK_INIT_IO; + break; + + case SK_INIT_RUN: + /* Initialization Level 2 */ + if (pAC->GIni.GILevel != SK_INIT_IO) { +#ifndef SK_DIAG + SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_HWI_E002, SKERR_HWI_E002MSG); +#endif /* !SK_DIAG */ + RetVal = 4; + break; + } + SkGeInit2(pAC, IoC); + + /* Level 2 successfully passed */ + pAC->GIni.GILevel = SK_INIT_RUN; + break; + + default: + SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_HWI_E003, SKERR_HWI_E003MSG); + RetVal = 3; + break; + } + + return(RetVal); +} /* SkGeInit */ + + +/****************************************************************************** + * + * SkGeDeInit() - Deinitialize the adapter + * + * Description: + * All ports of the adapter will be stopped if not already done. + * Do a software reset and switch off all LEDs. + * + * Returns: + * nothing + */ +void SkGeDeInit( +SK_AC *pAC, /* adapter context */ +SK_IOC IoC) /* IO context */ +{ + int i; + SK_U16 Word; + +#if (!defined(SK_SLIM) && !defined(VCPU)) + /* ensure I2C is ready */ + SkI2cWaitIrq(pAC, IoC); +#endif + + /* stop all current transfer activity */ + for (i = 0; i < pAC->GIni.GIMacsFound; i++) { + if (pAC->GIni.GP[i].PState != SK_PRT_STOP && + pAC->GIni.GP[i].PState != SK_PRT_RESET) { + + SkGeStopPort(pAC, IoC, i, SK_STOP_ALL, SK_HARD_RST); + } + } + + /* Reset all bits in the PCI STATUS register */ + /* + * Note: PCI Cfg cycles cannot be used, because they are not + * available on some platforms after 'boot time'. + */ + SK_IN16(IoC, PCI_C(PCI_STATUS), &Word); + + SK_OUT8(IoC, B2_TST_CTRL1, TST_CFG_WRITE_ON); + SK_OUT16(IoC, PCI_C(PCI_STATUS), (SK_U16)(Word | PCI_ERRBITS)); + SK_OUT8(IoC, B2_TST_CTRL1, TST_CFG_WRITE_OFF); + + /* do the reset, all LEDs are switched off now */ + SK_OUT8(IoC, B0_CTST, CS_RST_SET); + + pAC->GIni.GILevel = SK_INIT_DATA; +} /* SkGeDeInit */ + + +/****************************************************************************** + * + * SkGeInitPort() Initialize the specified port. + * + * Description: + * PRxQSize, PXSQSize, and PXAQSize has to be + * configured for the specified port before calling this function. + * The descriptor rings has to be initialized too. + * + * o (Re)configure queues of the specified port. + * o configure the MAC of the specified port. + * o put ASIC and MAC(s) in operational mode. + * o initialize Rx/Tx and Sync LED + * o initialize RAM Buffers and MAC FIFOs + * + * The port is ready to connect when returning. + * + * Note: + * The MAC's Rx and Tx state machine is still disabled when returning. + * + * Returns: + * 0: success + * 1: Queue size initialization error. The configured values + * for PRxQSize, PXSQSize, or PXAQSize are invalid for one + * or more queues. The specified port was NOT initialized. + * An error log entry was generated. + * 2: The port has to be stopped before it can be initialized again. + */ +int SkGeInitPort( +SK_AC *pAC, /* adapter context */ +SK_IOC IoC, /* IO context */ +int Port) /* Port to configure */ +{ + SK_GEPORT *pPrt; + + pPrt = &pAC->GIni.GP[Port]; + + if (SkGeCheckQSize(pAC, Port) != 0) { + SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_HWI_E004, SKERR_HWI_E004MSG); + return(1); + } + + if (pPrt->PState == SK_PRT_INIT || pPrt->PState == SK_PRT_RUN) { + SK_ERR_LOG(pAC, SK_ERRCL_SW, SKERR_HWI_E005, SKERR_HWI_E005MSG); + return(2); + } + + /* configuration ok, initialize the Port now */ + +#ifdef GENESIS + if (pAC->GIni.GIGenesis) { + /* initialize Rx, Tx and Link LED */ + /* + * If 1000BT Phy needs LED initialization than swap + * LED and XMAC initialization order + */ + SkGeXmitLED(pAC, IoC, MR_ADDR(Port, TX_LED_INI), SK_LED_ENA); + SkGeXmitLED(pAC, IoC, MR_ADDR(Port, RX_LED_INI), SK_LED_ENA); + /* The Link LED is initialized by RLMT or Diagnostics itself */ + + SkXmInitMac(pAC, IoC, Port); + } +#endif /* GENESIS */ + +#ifdef YUKON + if (pAC->GIni.GIYukon) { + + SkGmInitMac(pAC, IoC, Port); + } +#endif /* YUKON */ + + /* do NOT initialize the Link Sync Counter */ + + SkGeInitMacFifo(pAC, IoC, Port); + + SkGeInitRamBufs(pAC, IoC, Port); + + if (pPrt->PXSQSize != 0) { + /* enable Force Sync bit if synchronous queue available */ + SK_OUT8(IoC, MR_ADDR(Port, TXA_CTRL), TXA_ENA_FSYNC); + } + + SkGeInitBmu(pAC, IoC, Port); + + /* mark port as initialized */ + pPrt->PState = SK_PRT_INIT; + + return(0); +} /* SkGeInitPort */ |