diff options
Diffstat (limited to 'drivers/net/tg3.c')
| -rw-r--r-- | drivers/net/tg3.c | 77 |
1 files changed, 34 insertions, 43 deletions
diff --git a/drivers/net/tg3.c b/drivers/net/tg3.c index 01d3a271a04..ecbc10fed1a 100644 --- a/drivers/net/tg3.c +++ b/drivers/net/tg3.c @@ -12678,29 +12678,6 @@ static struct subsys_tbl_ent * __devinit tg3_lookup_by_subsys(struct tg3 *tp) static void __devinit tg3_get_eeprom_hw_cfg(struct tg3 *tp) { u32 val; - u16 pmcsr; - - /* On some early chips the SRAM cannot be accessed in D3hot state, - * so need make sure we're in D0. - */ - pci_read_config_word(tp->pdev, tp->pm_cap + PCI_PM_CTRL, &pmcsr); - pmcsr &= ~PCI_PM_CTRL_STATE_MASK; - pci_write_config_word(tp->pdev, tp->pm_cap + PCI_PM_CTRL, pmcsr); - msleep(1); - - /* Make sure register accesses (indirect or otherwise) - * will function correctly. - */ - pci_write_config_dword(tp->pdev, TG3PCI_MISC_HOST_CTRL, - tp->misc_host_ctrl); - - /* The memory arbiter has to be enabled in order for SRAM accesses - * to succeed. Normally on powerup the tg3 chip firmware will make - * sure it is enabled, but other entities such as system netboot - * code might disable it. - */ - val = tr32(MEMARB_MODE); - tw32(MEMARB_MODE, val | MEMARB_MODE_ENABLE); tp->phy_id = TG3_PHY_ID_INVALID; tp->led_ctrl = LED_CTRL_MODE_PHY_1; @@ -13498,14 +13475,17 @@ static int __devinit tg3_get_invariants(struct tg3 *tp) pci_cmd &= ~PCI_COMMAND_INVALIDATE; pci_write_config_word(tp->pdev, PCI_COMMAND, pci_cmd); - /* It is absolutely critical that TG3PCI_MISC_HOST_CTRL - * has the register indirect write enable bit set before - * we try to access any of the MMIO registers. It is also - * critical that the PCI-X hw workaround situation is decided - * before that as well. + /* Important! -- Make sure register accesses are byteswapped + * correctly. Also, for those chips that require it, make + * sure that indirect register accesses are enabled before + * the first operation. */ pci_read_config_dword(tp->pdev, TG3PCI_MISC_HOST_CTRL, &misc_ctrl_reg); + tp->misc_host_ctrl |= (misc_ctrl_reg & + MISC_HOST_CTRL_CHIPREV); + pci_write_config_dword(tp->pdev, TG3PCI_MISC_HOST_CTRL, + tp->misc_host_ctrl); tp->pci_chip_rev_id = (misc_ctrl_reg >> MISC_HOST_CTRL_CHIPREV_SHIFT); @@ -13661,12 +13641,6 @@ static int __devinit tg3_get_invariants(struct tg3 *tp) } while (bridge); } - /* Initialize misc host control in PCI block. */ - tp->misc_host_ctrl |= (misc_ctrl_reg & - MISC_HOST_CTRL_CHIPREV); - pci_write_config_dword(tp->pdev, TG3PCI_MISC_HOST_CTRL, - tp->misc_host_ctrl); - if (GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5704 || GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5714 || GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5717 || @@ -13851,6 +13825,9 @@ static int __devinit tg3_get_invariants(struct tg3 *tp) tp->pci_lat_timer); } + /* Important! -- It is critical that the PCI-X hw workaround + * situation is decided before the first MMIO register access. + */ if (GET_CHIP_REV(tp->pci_chip_rev_id) == CHIPREV_5700_BX) { /* 5700 BX chips need to have their TX producer index * mailboxes written twice to workaround a bug. @@ -13957,6 +13934,14 @@ static int __devinit tg3_get_invariants(struct tg3 *tp) GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5701))) tg3_flag_set(tp, SRAM_USE_CONFIG); + /* The memory arbiter has to be enabled in order for SRAM accesses + * to succeed. Normally on powerup the tg3 chip firmware will make + * sure it is enabled, but other entities such as system netboot + * code might disable it. + */ + val = tr32(MEMARB_MODE); + tw32(MEMARB_MODE, val | MEMARB_MODE_ENABLE); + /* Get eeprom hw config before calling tg3_set_power_state(). * In particular, the TG3_FLAG_IS_NIC flag must be * determined before calling tg3_set_power_state() so that @@ -13987,8 +13972,9 @@ static int __devinit tg3_get_invariants(struct tg3 *tp) tg3_flag(tp, 57765_PLUS)) tg3_flag_set(tp, CPMU_PRESENT); - /* Set up tp->grc_local_ctrl before calling tg3_power_up(). - * GPIO1 driven high will bring 5700's external PHY out of reset. + /* Set up tp->grc_local_ctrl before calling + * tg3_pwrsrc_switch_to_vmain(). GPIO1 driven high + * will bring 5700's external PHY out of reset. * It is also used as eeprom write protect on LOMs. */ tp->grc_local_ctrl = GRC_LCLCTRL_INT_ON_ATTN | GRC_LCLCTRL_AUTO_SEEPROM; @@ -14017,12 +14003,8 @@ static int __devinit tg3_get_invariants(struct tg3 *tp) GRC_LCLCTRL_GPIO_OUTPUT0; } - /* Force the chip into D0. */ - err = tg3_power_up(tp); - if (err) { - dev_err(&tp->pdev->dev, "Transition to D0 failed\n"); - return err; - } + /* Switch out of Vaux if it is a NIC */ + tg3_pwrsrc_switch_to_vmain(tp); /* Derive initial jumbo mode from MTU assigned in * ether_setup() via the alloc_etherdev() call @@ -15037,11 +15019,17 @@ static int __devinit tg3_init_one(struct pci_dev *pdev, goto err_out_free_res; } + err = pci_set_power_state(pdev, PCI_D0); + if (err) { + dev_err(&pdev->dev, "Transition to D0 failed, aborting\n"); + goto err_out_free_res; + } + dev = alloc_etherdev_mq(sizeof(*tp), TG3_IRQ_MAX_VECS); if (!dev) { dev_err(&pdev->dev, "Etherdev alloc failed, aborting\n"); err = -ENOMEM; - goto err_out_free_res; + goto err_out_power_down; } SET_NETDEV_DEV(dev, &pdev->dev); @@ -15356,6 +15344,9 @@ err_out_iounmap: err_out_free_dev: free_netdev(dev); +err_out_power_down: + pci_set_power_state(pdev, PCI_D3hot); + err_out_free_res: pci_release_regions(pdev); |