diff options
Diffstat (limited to 'drivers/net/wireless/ath/ath5k/ath5k.h')
| -rw-r--r-- | drivers/net/wireless/ath/ath5k/ath5k.h | 571 |
1 files changed, 388 insertions, 183 deletions
diff --git a/drivers/net/wireless/ath/ath5k/ath5k.h b/drivers/net/wireless/ath/ath5k/ath5k.h index fecbcd9a425..c2b2518c2ec 100644 --- a/drivers/net/wireless/ath/ath5k/ath5k.h +++ b/drivers/net/wireless/ath/ath5k/ath5k.h @@ -187,10 +187,9 @@ #define AR5K_TUNE_MAX_TXPOWER 63 #define AR5K_TUNE_DEFAULT_TXPOWER 25 #define AR5K_TUNE_TPC_TXPOWER false -#define ATH5K_TUNE_CALIBRATION_INTERVAL_FULL 10000 /* 10 sec */ +#define ATH5K_TUNE_CALIBRATION_INTERVAL_FULL 60000 /* 60 sec */ +#define ATH5K_TUNE_CALIBRATION_INTERVAL_SHORT 10000 /* 10 sec */ #define ATH5K_TUNE_CALIBRATION_INTERVAL_ANI 1000 /* 1 sec */ -#define ATH5K_TUNE_CALIBRATION_INTERVAL_NF 60000 /* 60 sec */ - #define ATH5K_TX_COMPLETE_POLL_INT 3000 /* 3 sec */ #define AR5K_INIT_CARR_SENSE_EN 1 @@ -262,16 +261,34 @@ #define AR5K_AGC_SETTLING_TURBO 37 -/* GENERIC CHIPSET DEFINITIONS */ -/* MAC Chips */ +/*****************************\ +* GENERIC CHIPSET DEFINITIONS * +\*****************************/ + +/** + * enum ath5k_version - MAC Chips + * @AR5K_AR5210: AR5210 (Crete) + * @AR5K_AR5211: AR5211 (Oahu/Maui) + * @AR5K_AR5212: AR5212 (Venice) and newer + */ enum ath5k_version { AR5K_AR5210 = 0, AR5K_AR5211 = 1, AR5K_AR5212 = 2, }; -/* PHY Chips */ +/** + * enum ath5k_radio - PHY Chips + * @AR5K_RF5110: RF5110 (Fez) + * @AR5K_RF5111: RF5111 (Sombrero) + * @AR5K_RF5112: RF2112/5112(A) (Derby/Derby2) + * @AR5K_RF2413: RF2413/2414 (Griffin/Griffin-Lite) + * @AR5K_RF5413: RF5413/5414/5424 (Eagle/Condor) + * @AR5K_RF2316: RF2315/2316 (Cobra SoC) + * @AR5K_RF2317: RF2317 (Spider SoC) + * @AR5K_RF2425: RF2425/2417 (Swan/Nalla) + */ enum ath5k_radio { AR5K_RF5110 = 0, AR5K_RF5111 = 1, @@ -303,11 +320,11 @@ enum ath5k_radio { #define AR5K_SREV_AR5213A 0x59 /* Hainan */ #define AR5K_SREV_AR2413 0x78 /* Griffin lite */ #define AR5K_SREV_AR2414 0x70 /* Griffin */ -#define AR5K_SREV_AR2315_R6 0x86 /* AP51-Light */ -#define AR5K_SREV_AR2315_R7 0x87 /* AP51-Full */ +#define AR5K_SREV_AR2315_R6 0x86 /* AP51-Light */ +#define AR5K_SREV_AR2315_R7 0x87 /* AP51-Full */ #define AR5K_SREV_AR5424 0x90 /* Condor */ -#define AR5K_SREV_AR2317_R1 0x90 /* AP61-Light */ -#define AR5K_SREV_AR2317_R2 0x91 /* AP61-Full */ +#define AR5K_SREV_AR2317_R1 0x90 /* AP61-Light */ +#define AR5K_SREV_AR2317_R2 0x91 /* AP61-Full */ #define AR5K_SREV_AR5413 0xa4 /* Eagle lite */ #define AR5K_SREV_AR5414 0xa0 /* Eagle */ #define AR5K_SREV_AR2415 0xb0 /* Talon */ @@ -344,32 +361,40 @@ enum ath5k_radio { /* TODO add support to mac80211 for vendor-specific rates and modes */ -/* +/** + * DOC: Atheros XR + * * Some of this information is based on Documentation from: * * http://madwifi-project.org/wiki/ChipsetFeatures/SuperAG * - * Modulation for Atheros' eXtended Range - range enhancing extension that is - * supposed to double the distance an Atheros client device can keep a - * connection with an Atheros access point. This is achieved by increasing - * the receiver sensitivity up to, -105dBm, which is about 20dB above what - * the 802.11 specifications demand. In addition, new (proprietary) data rates - * are introduced: 3, 2, 1, 0.5 and 0.25 MBit/s. + * Atheros' eXtended Range - range enhancing extension is a modulation scheme + * that is supposed to double the link distance between an Atheros XR-enabled + * client device with an Atheros XR-enabled access point. This is achieved + * by increasing the receiver sensitivity up to, -105dBm, which is about 20dB + * above what the 802.11 specifications demand. In addition, new (proprietary) + * data rates are introduced: 3, 2, 1, 0.5 and 0.25 MBit/s. * * Please note that can you either use XR or TURBO but you cannot use both, * they are exclusive. * + * Also note that we do not plan to support XR mode at least for now. You can + * get a mode similar to XR by using 5MHz bwmode. */ -#define MODULATION_XR 0x00000200 -/* - * Modulation for Atheros' Turbo G and Turbo A, its supposed to provide a - * throughput transmission speed up to 40Mbit/s-60Mbit/s at a 108Mbit/s - * signaling rate achieved through the bonding of two 54Mbit/s 802.11g - * channels. To use this feature your Access Point must also support it. + + +/** + * DOC: Atheros SuperAG + * + * In addition to XR we have another modulation scheme called TURBO mode + * that is supposed to provide a throughput transmission speed up to 40Mbit/s + * -60Mbit/s at a 108Mbit/s signaling rate achieved through the bonding of two + * 54Mbit/s 802.11g channels. To use this feature both ends must support it. * There is also a distinction between "static" and "dynamic" turbo modes: * * - Static: is the dumb version: devices set to this mode stick to it until * the mode is turned off. + * * - Dynamic: is the intelligent version, the network decides itself if it * is ok to use turbo. As soon as traffic is detected on adjacent channels * (which would get used in turbo mode), or when a non-turbo station joins @@ -383,24 +408,39 @@ enum ath5k_radio { * * http://www.pcworld.com/article/id,113428-page,1/article.html * - * The channel bonding seems to be driver specific though. In addition to - * deciding what channels will be used, these "Turbo" modes are accomplished - * by also enabling the following features: + * The channel bonding seems to be driver specific though. + * + * In addition to TURBO modes we also have the following features for even + * greater speed-up: * * - Bursting: allows multiple frames to be sent at once, rather than pausing * after each frame. Bursting is a standards-compliant feature that can be * used with any Access Point. + * * - Fast frames: increases the amount of information that can be sent per * frame, also resulting in a reduction of transmission overhead. It is a * proprietary feature that needs to be supported by the Access Point. + * * - Compression: data frames are compressed in real time using a Lempel Ziv * algorithm. This is done transparently. Once this feature is enabled, * compression and decompression takes place inside the chipset, without * putting additional load on the host CPU. * + * As with XR we also don't plan to support SuperAG features for now. You can + * get a mode similar to TURBO by using 40MHz bwmode. */ -#define MODULATION_TURBO 0x00000080 + +/** + * enum ath5k_driver_mode - PHY operation mode + * @AR5K_MODE_11A: 802.11a + * @AR5K_MODE_11B: 802.11b + * @AR5K_MODE_11G: 801.11g + * @AR5K_MODE_MAX: Used for boundary checks + * + * Do not change the order here, we use these as + * array indices and it also maps EEPROM structures. + */ enum ath5k_driver_mode { AR5K_MODE_11A = 0, AR5K_MODE_11B = 1, @@ -408,30 +448,64 @@ enum ath5k_driver_mode { AR5K_MODE_MAX = 3 }; +/** + * enum ath5k_ant_mode - Antenna operation mode + * @AR5K_ANTMODE_DEFAULT: Default antenna setup + * @AR5K_ANTMODE_FIXED_A: Only antenna A is present + * @AR5K_ANTMODE_FIXED_B: Only antenna B is present + * @AR5K_ANTMODE_SINGLE_AP: STA locked on a single ap + * @AR5K_ANTMODE_SECTOR_AP: AP with tx antenna set on tx desc + * @AR5K_ANTMODE_SECTOR_STA: STA with tx antenna set on tx desc + * @AR5K_ANTMODE_DEBUG: Debug mode -A -> Rx, B-> Tx- + * @AR5K_ANTMODE_MAX: Used for boundary checks + * + * For more infos on antenna control check out phy.c + */ enum ath5k_ant_mode { - AR5K_ANTMODE_DEFAULT = 0, /* default antenna setup */ - AR5K_ANTMODE_FIXED_A = 1, /* only antenna A is present */ - AR5K_ANTMODE_FIXED_B = 2, /* only antenna B is present */ - AR5K_ANTMODE_SINGLE_AP = 3, /* sta locked on a single ap */ - AR5K_ANTMODE_SECTOR_AP = 4, /* AP with tx antenna set on tx desc */ - AR5K_ANTMODE_SECTOR_STA = 5, /* STA with tx antenna set on tx desc */ - AR5K_ANTMODE_DEBUG = 6, /* Debug mode -A -> Rx, B-> Tx- */ + AR5K_ANTMODE_DEFAULT = 0, + AR5K_ANTMODE_FIXED_A = 1, + AR5K_ANTMODE_FIXED_B = 2, + AR5K_ANTMODE_SINGLE_AP = 3, + AR5K_ANTMODE_SECTOR_AP = 4, + AR5K_ANTMODE_SECTOR_STA = 5, + AR5K_ANTMODE_DEBUG = 6, AR5K_ANTMODE_MAX, }; +/** + * enum ath5k_bw_mode - Bandwidth operation mode + * @AR5K_BWMODE_DEFAULT: 20MHz, default operation + * @AR5K_BWMODE_5MHZ: Quarter rate + * @AR5K_BWMODE_10MHZ: Half rate + * @AR5K_BWMODE_40MHZ: Turbo + */ enum ath5k_bw_mode { - AR5K_BWMODE_DEFAULT = 0, /* 20MHz, default operation */ - AR5K_BWMODE_5MHZ = 1, /* Quarter rate */ - AR5K_BWMODE_10MHZ = 2, /* Half rate */ - AR5K_BWMODE_40MHZ = 3 /* Turbo */ + AR5K_BWMODE_DEFAULT = 0, + AR5K_BWMODE_5MHZ = 1, + AR5K_BWMODE_10MHZ = 2, + AR5K_BWMODE_40MHZ = 3 }; + + /****************\ TX DEFINITIONS \****************/ -/* - * TX Status descriptor +/** + * struct ath5k_tx_status - TX Status descriptor + * @ts_seqnum: Sequence number + * @ts_tstamp: Timestamp + * @ts_status: Status code + * @ts_final_idx: Final transmission series index + * @ts_final_retry: Final retry count + * @ts_rssi: RSSI for received ACK + * @ts_shortretry: Short retry count + * @ts_virtcol: Virtual collision count + * @ts_antenna: Antenna used + * + * TX status descriptor gets filled by the hw + * on each transmission attempt. */ struct ath5k_tx_status { u16 ts_seqnum; @@ -454,7 +528,6 @@ struct ath5k_tx_status { * enum ath5k_tx_queue - Queue types used to classify tx queues. * @AR5K_TX_QUEUE_INACTIVE: q is unused -- see ath5k_hw_release_tx_queue * @AR5K_TX_QUEUE_DATA: A normal data queue - * @AR5K_TX_QUEUE_XR_DATA: An XR-data queue * @AR5K_TX_QUEUE_BEACON: The beacon queue * @AR5K_TX_QUEUE_CAB: The after-beacon queue * @AR5K_TX_QUEUE_UAPSD: Unscheduled Automatic Power Save Delivery queue @@ -462,7 +535,6 @@ struct ath5k_tx_status { enum ath5k_tx_queue { AR5K_TX_QUEUE_INACTIVE = 0, AR5K_TX_QUEUE_DATA, - AR5K_TX_QUEUE_XR_DATA, AR5K_TX_QUEUE_BEACON, AR5K_TX_QUEUE_CAB, AR5K_TX_QUEUE_UAPSD, @@ -471,36 +543,46 @@ enum ath5k_tx_queue { #define AR5K_NUM_TX_QUEUES 10 #define AR5K_NUM_TX_QUEUES_NOQCU 2 -/* - * Queue syb-types to classify normal data queues. +/** + * enum ath5k_tx_queue_subtype - Queue sub-types to classify normal data queues + * @AR5K_WME_AC_BK: Background traffic + * @AR5K_WME_AC_BE: Best-effort (normal) traffic + * @AR5K_WME_AC_VI: Video traffic + * @AR5K_WME_AC_VO: Voice traffic + * * These are the 4 Access Categories as defined in * WME spec. 0 is the lowest priority and 4 is the * highest. Normal data that hasn't been classified * goes to the Best Effort AC. */ enum ath5k_tx_queue_subtype { - AR5K_WME_AC_BK = 0, /*Background traffic*/ - AR5K_WME_AC_BE, /*Best-effort (normal) traffic*/ - AR5K_WME_AC_VI, /*Video traffic*/ - AR5K_WME_AC_VO, /*Voice traffic*/ + AR5K_WME_AC_BK = 0, + AR5K_WME_AC_BE, + AR5K_WME_AC_VI, + AR5K_WME_AC_VO, }; -/* - * Queue ID numbers as returned by the hw functions, each number - * represents a hw queue. If hw does not support hw queues - * (eg 5210) all data goes in one queue. These match - * d80211 definitions (net80211/MadWiFi don't use them). +/** + * enum ath5k_tx_queue_id - Queue ID numbers as returned by the hw functions + * @AR5K_TX_QUEUE_ID_NOQCU_DATA: Data queue on AR5210 (no QCU available) + * @AR5K_TX_QUEUE_ID_NOQCU_BEACON: Beacon queue on AR5210 (no QCU available) + * @AR5K_TX_QUEUE_ID_DATA_MIN: Data queue min index + * @AR5K_TX_QUEUE_ID_DATA_MAX: Data queue max index + * @AR5K_TX_QUEUE_ID_CAB: Content after beacon queue + * @AR5K_TX_QUEUE_ID_BEACON: Beacon queue + * @AR5K_TX_QUEUE_ID_UAPSD: Urgent Automatic Power Save Delivery, + * + * Each number represents a hw queue. If hw does not support hw queues + * (eg 5210) all data goes in one queue. */ enum ath5k_tx_queue_id { AR5K_TX_QUEUE_ID_NOQCU_DATA = 0, AR5K_TX_QUEUE_ID_NOQCU_BEACON = 1, - AR5K_TX_QUEUE_ID_DATA_MIN = 0, /*IEEE80211_TX_QUEUE_DATA0*/ - AR5K_TX_QUEUE_ID_DATA_MAX = 3, /*IEEE80211_TX_QUEUE_DATA3*/ - AR5K_TX_QUEUE_ID_DATA_SVP = 5, /*IEEE80211_TX_QUEUE_SVP - Spectralink Voice Protocol*/ - AR5K_TX_QUEUE_ID_CAB = 6, /*IEEE80211_TX_QUEUE_AFTER_BEACON*/ - AR5K_TX_QUEUE_ID_BEACON = 7, /*IEEE80211_TX_QUEUE_BEACON*/ - AR5K_TX_QUEUE_ID_UAPSD = 8, - AR5K_TX_QUEUE_ID_XR_DATA = 9, + AR5K_TX_QUEUE_ID_DATA_MIN = 0, + AR5K_TX_QUEUE_ID_DATA_MAX = 3, + AR5K_TX_QUEUE_ID_UAPSD = 7, + AR5K_TX_QUEUE_ID_CAB = 8, + AR5K_TX_QUEUE_ID_BEACON = 9, }; /* @@ -521,46 +603,70 @@ enum ath5k_tx_queue_id { #define AR5K_TXQ_FLAG_POST_FR_BKOFF_DIS 0x1000 /* Disable backoff while bursting */ #define AR5K_TXQ_FLAG_COMPRESSION_ENABLE 0x2000 /* Enable hw compression -not implemented-*/ -/* - * Data transmit queue state. One of these exists for each - * hardware transmit queue. Packets sent to us from above - * are assigned to queues based on their priority. Not all - * devices support a complete set of hardware transmit queues. - * For those devices the array sc_ac2q will map multiple - * priorities to fewer hardware queues (typically all to one - * hardware queue). +/** + * struct ath5k_txq - Transmit queue state + * @qnum: Hardware q number + * @link: Link ptr in last TX desc + * @q: Transmit queue (&struct list_head) + * @lock: Lock on q and link + * @setup: Is the queue configured + * @txq_len:Number of queued buffers + * @txq_max: Max allowed num of queued buffers + * @txq_poll_mark: Used to check if queue got stuck + * @txq_stuck: Queue stuck counter + * + * One of these exists for each hardware transmit queue. + * Packets sent to us from above are assigned to queues based + * on their priority. Not all devices support a complete set + * of hardware transmit queues. For those devices the array + * sc_ac2q will map multiple priorities to fewer hardware queues + * (typically all to one hardware queue). */ struct ath5k_txq { - unsigned int qnum; /* hardware q number */ - u32 *link; /* link ptr in last TX desc */ - struct list_head q; /* transmit queue */ - spinlock_t lock; /* lock on q and link */ + unsigned int qnum; + u32 *link; + struct list_head q; + spinlock_t lock; bool setup; - int txq_len; /* number of queued buffers */ - int txq_max; /* max allowed num of queued buffers */ + int txq_len; + int txq_max; bool txq_poll_mark; - unsigned int txq_stuck; /* informational counter */ + unsigned int txq_stuck; }; -/* - * A struct to hold tx queue's parameters +/** + * struct ath5k_txq_info - A struct to hold TX queue's parameters + * @tqi_type: One of enum ath5k_tx_queue + * @tqi_subtype: One of enum ath5k_tx_queue_subtype + * @tqi_flags: TX queue flags (see above) + * @tqi_aifs: Arbitrated Inter-frame Space + * @tqi_cw_min: Minimum Contention Window + * @tqi_cw_max: Maximum Contention Window + * @tqi_cbr_period: Constant bit rate period + * @tqi_ready_time: Time queue waits after an event when RDYTIME is enabled */ struct ath5k_txq_info { enum ath5k_tx_queue tqi_type; enum ath5k_tx_queue_subtype tqi_subtype; - u16 tqi_flags; /* Tx queue flags (see above) */ - u8 tqi_aifs; /* Arbitrated Interframe Space */ - u16 tqi_cw_min; /* Minimum Contention Window */ - u16 tqi_cw_max; /* Maximum Contention Window */ - u32 tqi_cbr_period; /* Constant bit rate period */ + u16 tqi_flags; + u8 tqi_aifs; + u16 tqi_cw_min; + u16 tqi_cw_max; + u32 tqi_cbr_period; u32 tqi_cbr_overflow_limit; u32 tqi_burst_time; - u32 tqi_ready_time; /* Time queue waits after an event */ + u32 tqi_ready_time; }; -/* - * Transmit packet types. - * used on tx control descriptor +/** + * enum ath5k_pkt_type - Transmit packet types + * @AR5K_PKT_TYPE_NORMAL: Normal data + * @AR5K_PKT_TYPE_ATIM: ATIM + * @AR5K_PKT_TYPE_PSPOLL: PS-Poll + * @AR5K_PKT_TYPE_BEACON: Beacon + * @AR5K_PKT_TYPE_PROBE_RESP: Probe response + * @AR5K_PKT_TYPE_PIFS: PIFS + * Used on tx control descriptor */ enum ath5k_pkt_type { AR5K_PKT_TYPE_NORMAL = 0, @@ -583,27 +689,23 @@ enum ath5k_pkt_type { (ah->ah_txpower.txp_rates_power_table[(_r)] & 0x3f) << (_v) \ ) -/* - * DMA size definitions (2^(n+2)) - */ -enum ath5k_dmasize { - AR5K_DMASIZE_4B = 0, - AR5K_DMASIZE_8B, - AR5K_DMASIZE_16B, - AR5K_DMASIZE_32B, - AR5K_DMASIZE_64B, - AR5K_DMASIZE_128B, - AR5K_DMASIZE_256B, - AR5K_DMASIZE_512B -}; /****************\ RX DEFINITIONS \****************/ -/* - * RX Status descriptor +/** + * struct ath5k_rx_status - RX Status descriptor + * @rs_datalen: Data length + * @rs_tstamp: Timestamp + * @rs_status: Status code + * @rs_phyerr: PHY error mask + * @rs_rssi: RSSI in 0.5dbm units + * @rs_keyix: Index to the key used for decrypting + * @rs_rate: Rate used to decode the frame + * @rs_antenna: Antenna used to receive the frame + * @rs_more: Indicates this is a frame fragment (Fast frames) */ struct ath5k_rx_status { u16 rs_datalen; @@ -645,10 +747,18 @@ struct ath5k_rx_status { #define TSF_TO_TU(_tsf) (u32)((_tsf) >> 10) + /*******************************\ GAIN OPTIMIZATION DEFINITIONS \*******************************/ +/** + * enum ath5k_rfgain - RF Gain optimization engine state + * @AR5K_RFGAIN_INACTIVE: Engine disabled + * @AR5K_RFGAIN_ACTIVE: Probe active + * @AR5K_RFGAIN_READ_REQUESTED: Probe requested + * @AR5K_RFGAIN_NEED_CHANGE: Gain_F needs change + */ enum ath5k_rfgain { AR5K_RFGAIN_INACTIVE = 0, AR5K_RFGAIN_ACTIVE, @@ -656,6 +766,16 @@ enum ath5k_rfgain { AR5K_RFGAIN_NEED_CHANGE, }; +/** + * struct ath5k_gain - RF Gain optimization engine state data + * @g_step_idx: Current step index + * @g_current: Current gain + * @g_target: Target gain + * @g_low: Low gain boundary + * @g_high: High gain boundary + * @g_f_corr: Gain_F correction + * @g_state: One of enum ath5k_rfgain + */ struct ath5k_gain { u8 g_step_idx; u8 g_current; @@ -666,6 +786,8 @@ struct ath5k_gain { u8 g_state; }; + + /********************\ COMMON DEFINITIONS \********************/ @@ -674,9 +796,14 @@ struct ath5k_gain { #define AR5K_SLOT_TIME_20 880 #define AR5K_SLOT_TIME_MAX 0xffff -/* - * The following structure is used to map 2GHz channels to - * 5GHz Atheros channels. +/** + * struct ath5k_athchan_2ghz - 2GHz to 5GHZ map for RF5111 + * @a2_flags: Channel flags (internal) + * @a2_athchan: HW channel number (internal) + * + * This structure is used to map 2GHz channels to + * 5GHz Atheros channels on 2111 frequency converter + * that comes together with RF5111 * TODO: Clean up */ struct ath5k_athchan_2ghz { @@ -684,36 +811,80 @@ struct ath5k_athchan_2ghz { u16 a2_athchan; }; +/** + * enum ath5k_dmasize - DMA size definitions (2^(n+2)) + * @AR5K_DMASIZE_4B: 4Bytes + * @AR5K_DMASIZE_8B: 8Bytes + * @AR5K_DMASIZE_16B: 16Bytes + * @AR5K_DMASIZE_32B: 32Bytes + * @AR5K_DMASIZE_64B: 64Bytes (Default) + * @AR5K_DMASIZE_128B: 128Bytes + * @AR5K_DMASIZE_256B: 256Bytes + * @AR5K_DMASIZE_512B: 512Bytes + * + * These are used to set DMA burst size on hw + * + * Note: Some platforms can't handle more than 4Bytes + * be careful on embedded boards. + */ +enum ath5k_dmasize { + AR5K_DMASIZE_4B = 0, + AR5K_DMASIZE_8B, + AR5K_DMASIZE_16B, + AR5K_DMASIZE_32B, + AR5K_DMASIZE_64B, + AR5K_DMASIZE_128B, + AR5K_DMASIZE_256B, + AR5K_DMASIZE_512B +}; + + /******************\ RATE DEFINITIONS \******************/ /** + * DOC: Rate codes + * * Seems the ar5xxx hardware supports up to 32 rates, indexed by 1-32. * * The rate code is used to get the RX rate or set the TX rate on the * hardware descriptors. It is also used for internal modulation control * and settings. * - * This is the hardware rate map we are aware of: - * - * rate_code 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 - * rate_kbps 3000 1000 ? ? ? 2000 500 48000 - * - * rate_code 0x09 0x0A 0x0B 0x0C 0x0D 0x0E 0x0F 0x10 - * rate_kbps 24000 12000 6000 54000 36000 18000 9000 ? + * This is the hardware rate map we are aware of (html unfriendly): * - * rate_code 17 18 19 20 21 22 23 24 - * rate_kbps ? ? ? ? ? ? ? 11000 + * Rate code Rate (Kbps) + * --------- ----------- + * 0x01 3000 (XR) + * 0x02 1000 (XR) + * 0x03 250 (XR) + * 0x04 - 05 -Reserved- + * 0x06 2000 (XR) + * 0x07 500 (XR) + * 0x08 48000 (OFDM) + * 0x09 24000 (OFDM) + * 0x0A 12000 (OFDM) + * 0x0B 6000 (OFDM) + * 0x0C 54000 (OFDM) + * 0x0D 36000 (OFDM) + * 0x0E 18000 (OFDM) + * 0x0F 9000 (OFDM) + * 0x10 - 17 -Reserved- + * 0x18 11000L (CCK) + * 0x19 5500L (CCK) + * 0x1A 2000L (CCK) + * 0x1B 1000L (CCK) + * 0x1C 11000S (CCK) + * 0x1D 5500S (CCK) + * 0x1E 2000S (CCK) + * 0x1F -Reserved- * - * rate_code 25 26 27 28 29 30 31 32 - * rate_kbps 5500 2000 1000 11000S 5500S 2000S ? ? - * - * "S" indicates CCK rates with short preamble. + * "S" indicates CCK rates with short preamble and "L" with long preamble. * * AR5211 has different rate codes for CCK (802.11B) rates. It only uses the - * lowest 4 bits, so they are the same as below with a 0xF mask. + * lowest 4 bits, so they are the same as above with a 0xF mask. * (0xB, 0xA, 0x9 and 0x8 for 1M, 2M, 5.5M and 11M). * We handle this in ath5k_setup_bands(). */ @@ -733,13 +904,9 @@ struct ath5k_athchan_2ghz { #define ATH5K_RATE_CODE_36M 0x0D #define ATH5K_RATE_CODE_48M 0x08 #define ATH5K_RATE_CODE_54M 0x0C -/* XR */ -#define ATH5K_RATE_CODE_XR_500K 0x07 -#define ATH5K_RATE_CODE_XR_1M 0x02 -#define ATH5K_RATE_CODE_XR_2M 0x06 -#define ATH5K_RATE_CODE_XR_3M 0x01 -/* adding this flag to rate_code enables short preamble */ +/* Adding this flag to rate_code on B rates + * enables short preamble */ #define AR5K_SET_SHORT_PREAMBLE 0x04 /* @@ -747,7 +914,7 @@ struct ath5k_athchan_2ghz { */ #define AR5K_KEYCACHE_SIZE 8 -extern int ath5k_modparam_nohwcrypt; +extern bool ath5k_modparam_nohwcrypt; /***********************\ HW RELATED DEFINITIONS @@ -769,49 +936,65 @@ extern int ath5k_modparam_nohwcrypt; /** * enum ath5k_int - Hardware interrupt masks helpers + * @AR5K_INT_RXOK: Frame successfully received + * @AR5K_INT_RXDESC: Request RX descriptor/Read RX descriptor + * @AR5K_INT_RXERR: Frame reception failed + * @AR5K_INT_RXNOFRM: No frame received within a specified time period + * @AR5K_INT_RXEOL: Reached "End Of List", means we need more RX descriptors + * @AR5K_INT_RXORN: Indicates we got RX FIFO overrun. Note that Rx overrun is + * not always fatal, on some chips we can continue operation + * without resetting the card, that's why %AR5K_INT_FATAL is not + * common for all chips. + * @AR5K_INT_RX_ALL: Mask to identify all RX related interrupts + * + * @AR5K_INT_TXOK: Frame transmission success + * @AR5K_INT_TXDESC: Request TX descriptor/Read TX status descriptor + * @AR5K_INT_TXERR: Frame transmission failure + * @AR5K_INT_TXEOL: Received End Of List for VEOL (Virtual End Of List). The + * Queue Control Unit (QCU) signals an EOL interrupt only if a + * descriptor's LinkPtr is NULL. For more details, refer to: + * "http://www.freepatentsonline.com/20030225739.html" + * @AR5K_INT_TXNOFRM: No frame was transmitted within a specified time period + * @AR5K_INT_TXURN: Indicates we got TX FIFO underrun. In such case we should + * increase the TX trigger threshold. + * @AR5K_INT_TX_ALL: Mask to identify all TX related interrupts * - * @AR5K_INT_RX: mask to identify received frame interrupts, of type - * AR5K_ISR_RXOK or AR5K_ISR_RXERR - * @AR5K_INT_RXDESC: Request RX descriptor/Read RX descriptor (?) - * @AR5K_INT_RXNOFRM: No frame received (?) - * @AR5K_INT_RXEOL: received End Of List for VEOL (Virtual End Of List). The - * Queue Control Unit (QCU) signals an EOL interrupt only if a descriptor's - * LinkPtr is NULL. For more details, refer to: - * http://www.freepatentsonline.com/20030225739.html - * @AR5K_INT_RXORN: Indicates we got RX overrun (eg. no more descriptors). - * Note that Rx overrun is not always fatal, on some chips we can continue - * operation without resetting the card, that's why int_fatal is not - * common for all chips. - * @AR5K_INT_TX: mask to identify received frame interrupts, of type - * AR5K_ISR_TXOK or AR5K_ISR_TXERR - * @AR5K_INT_TXDESC: Request TX descriptor/Read TX status descriptor (?) - * @AR5K_INT_TXURN: received when we should increase the TX trigger threshold - * We currently do increments on interrupt by - * (AR5K_TUNE_MAX_TX_FIFO_THRES - current_trigger_level) / 2 * @AR5K_INT_MIB: Indicates the either Management Information Base counters or - * one of the PHY error counters reached the maximum value and should be - * read and cleared. + * one of the PHY error counters reached the maximum value and + * should be read and cleared. + * @AR5K_INT_SWI: Software triggered interrupt. * @AR5K_INT_RXPHY: RX PHY Error * @AR5K_INT_RXKCM: RX Key cache miss * @AR5K_INT_SWBA: SoftWare Beacon Alert - indicates its time to send a - * beacon that must be handled in software. The alternative is if you - * have VEOL support, in that case you let the hardware deal with things. + * beacon that must be handled in software. The alternative is if + * you have VEOL support, in that case you let the hardware deal + * with things. + * @AR5K_INT_BRSSI: Beacon received with an RSSI value below our threshold * @AR5K_INT_BMISS: If in STA mode this indicates we have stopped seeing - * beacons from the AP have associated with, we should probably try to - * reassociate. When in IBSS mode this might mean we have not received - * any beacons from any local stations. Note that every station in an - * IBSS schedules to send beacons at the Target Beacon Transmission Time - * (TBTT) with a random backoff. - * @AR5K_INT_BNR: Beacon Not Ready interrupt - ?? - * @AR5K_INT_GPIO: GPIO interrupt is used for RF Kill, disabled for now - * until properly handled - * @AR5K_INT_FATAL: Fatal errors were encountered, typically caused by DMA - * errors. These types of errors we can enable seem to be of type - * AR5K_SIMR2_MCABT, AR5K_SIMR2_SSERR and AR5K_SIMR2_DPERR. + * beacons from the AP have associated with, we should probably + * try to reassociate. When in IBSS mode this might mean we have + * not received any beacons from any local stations. Note that + * every station in an IBSS schedules to send beacons at the + * Target Beacon Transmission Time (TBTT) with a random backoff. + * @AR5K_INT_BNR: Beacon queue got triggered (DMA beacon alert) while empty. + * @AR5K_INT_TIM: Beacon with local station's TIM bit set + * @AR5K_INT_DTIM: Beacon with DTIM bit and zero DTIM count received + * @AR5K_INT_DTIM_SYNC: DTIM sync lost + * @AR5K_INT_GPIO: GPIO interrupt is used for RF Kill switches connected to + * our GPIO pins. + * @AR5K_INT_BCN_TIMEOUT: Beacon timeout, we waited after TBTT but got noting + * @AR5K_INT_CAB_TIMEOUT: We waited for CAB traffic after the beacon but got + * nothing or an incomplete CAB frame sequence. + * @AR5K_INT_QCBRORN: A queue got it's CBR counter expired + * @AR5K_INT_QCBRURN: A queue got triggered wile empty + * @AR5K_INT_QTRIG: A queue got triggered + * + * @AR5K_INT_FATAL: Fatal errors were encountered, typically caused by bus/DMA + * errors. Indicates we need to reset the card. * @AR5K_INT_GLOBAL: Used to clear and set the IER - * @AR5K_INT_NOCARD: signals the card has been removed - * @AR5K_INT_COMMON: common interrupts shared among MACs with the same - * bit value + * @AR5K_INT_NOCARD: Signals the card has been removed + * @AR5K_INT_COMMON: Common interrupts shared among MACs with the same + * bit value * * These are mapped to take advantage of some common bits * between the MACs, to be able to set intr properties @@ -847,15 +1030,15 @@ enum ath5k_int { AR5K_INT_GPIO = 0x01000000, AR5K_INT_BCN_TIMEOUT = 0x02000000, /* Non common */ AR5K_INT_CAB_TIMEOUT = 0x04000000, /* Non common */ - AR5K_INT_RX_DOPPLER = 0x08000000, /* Non common */ - AR5K_INT_QCBRORN = 0x10000000, /* Non common */ - AR5K_INT_QCBRURN = 0x20000000, /* Non common */ - AR5K_INT_QTRIG = 0x40000000, /* Non common */ + AR5K_INT_QCBRORN = 0x08000000, /* Non common */ + AR5K_INT_QCBRURN = 0x10000000, /* Non common */ + AR5K_INT_QTRIG = 0x20000000, /* Non common */ AR5K_INT_GLOBAL = 0x80000000, AR5K_INT_TX_ALL = AR5K_INT_TXOK | AR5K_INT_TXDESC | AR5K_INT_TXERR + | AR5K_INT_TXNOFRM | AR5K_INT_TXEOL | AR5K_INT_TXURN, @@ -891,15 +1074,32 @@ enum ath5k_int { AR5K_INT_NOCARD = 0xffffffff }; -/* mask which calibration is active at the moment */ +/** + * enum ath5k_calibration_mask - Mask which calibration is active at the moment + * @AR5K_CALIBRATION_FULL: Full calibration (AGC + SHORT) + * @AR5K_CALIBRATION_SHORT: Short calibration (NF + I/Q) + * @AR5K_CALIBRATION_NF: Noise Floor calibration + * @AR5K_CALIBRATION_ANI: Adaptive Noise Immunity + */ enum ath5k_calibration_mask { AR5K_CALIBRATION_FULL = 0x01, AR5K_CALIBRATION_SHORT = 0x02, - AR5K_CALIBRATION_ANI = 0x04, + AR5K_CALIBRATION_NF = 0x04, + AR5K_CALIBRATION_ANI = 0x08, }; -/* - * Power management +/** + * enum ath5k_power_mode - Power management modes + * @AR5K_PM_UNDEFINED: Undefined + * @AR5K_PM_AUTO: Allow card to sleep if possible + * @AR5K_PM_AWAKE: Force card to wake up + * @AR5K_PM_FULL_SLEEP: Force card to full sleep (DANGEROUS) + * @AR5K_PM_NETWORK_SLEEP: Allow to sleep for a specified duration + * + * Currently only PM_AWAKE is used, FULL_SLEEP and NETWORK_SLEEP/AUTO + * are also known to have problems on some cards. This is not a big + * problem though because we can have almost the same effect as + * FULL_SLEEP by putting card on warm reset (it's almost powered down). */ enum ath5k_power_mode { AR5K_PM_UNDEFINED = 0, @@ -957,6 +1157,8 @@ struct ath5k_capabilities { } cap_queues; bool cap_has_phyerr_counters; + bool cap_has_mrr_support; + bool cap_needs_2GHz_ovr; }; /* size of noise floor history (keep it a power of two) */ @@ -1072,13 +1274,11 @@ struct ath5k_hw { dma_addr_t desc_daddr; /* DMA (physical) address */ size_t desc_len; /* size of TX/RX descriptors */ - DECLARE_BITMAP(status, 6); + DECLARE_BITMAP(status, 4); #define ATH_STAT_INVALID 0 /* disable hardware accesses */ -#define ATH_STAT_MRRETRY 1 /* multi-rate retry support */ -#define ATH_STAT_PROMISC 2 -#define ATH_STAT_LEDSOFT 3 /* enable LED gpio status */ -#define ATH_STAT_STARTED 4 /* opened & irqs enabled */ -#define ATH_STAT_2G_DISABLED 5 /* multiband radio without 2G */ +#define ATH_STAT_PROMISC 1 +#define ATH_STAT_LEDSOFT 2 /* enable LED gpio status */ +#define ATH_STAT_STARTED 3 /* opened & irqs enabled */ unsigned int filter_flags; /* HW flags, AR5K_RX_FILTER_* */ struct ieee80211_channel *curchan; /* current h/w channel */ @@ -1097,6 +1297,7 @@ struct ath5k_hw { led_on; /* pin setting for LED on */ struct work_struct reset_work; /* deferred chip reset */ + struct work_struct calib_work; /* deferred phy calibration */ struct list_head rxbuf; /* receive buffer */ spinlock_t rxbuflock; @@ -1113,8 +1314,6 @@ struct ath5k_hw { struct ath5k_rfkill rf_kill; - struct tasklet_struct calib; /* calibration tasklet */ - spinlock_t block; /* protects beacon */ struct tasklet_struct beacontq; /* beacon intr tasklet */ struct list_head bcbuf; /* beacon buffer */ @@ -1144,7 +1343,7 @@ struct ath5k_hw { enum ath5k_int ah_imr; struct ieee80211_channel *ah_current_channel; - bool ah_calibration; + bool ah_iq_cal_needed; bool ah_single_chip; enum ath5k_version ah_version; @@ -1187,7 +1386,13 @@ struct ath5k_hw { u32 ah_txq_imr_cbrurn; u32 ah_txq_imr_qtrig; u32 ah_txq_imr_nofrm; - u32 ah_txq_isr; + + u32 ah_txq_isr_txok_all; + u32 ah_txq_isr_txurn; + u32 ah_txq_isr_qcborn; + u32 ah_txq_isr_qcburn; + u32 ah_txq_isr_qtrig; + u32 *ah_rf_banks; size_t ah_rf_banks_size; size_t ah_rf_regs_count; @@ -1228,8 +1433,8 @@ struct ath5k_hw { /* Calibration timestamp */ unsigned long ah_cal_next_full; + unsigned long ah_cal_next_short; unsigned long ah_cal_next_ani; - unsigned long ah_cal_next_nf; /* Calibration mask */ u8 ah_cal_mask; @@ -1338,11 +1543,11 @@ void ath5k_hw_stop_rx_pcu(struct ath5k_hw *ah); u64 ath5k_hw_get_tsf64(struct ath5k_hw *ah); void ath5k_hw_set_tsf64(struct ath5k_hw *ah, u64 tsf64); void ath5k_hw_reset_tsf(struct ath5k_hw *ah); -void ath5k_hw_init_beacon(struct ath5k_hw *ah, u32 next_beacon, u32 interval); +void ath5k_hw_init_beacon_timers(struct ath5k_hw *ah, u32 next_beacon, + u32 interval); bool ath5k_hw_check_beacon_timers(struct ath5k_hw *ah, int intval); /* Init function */ -void ath5k_hw_pcu_init(struct ath5k_hw *ah, enum nl80211_iftype op_mode, - u8 mode); +void ath5k_hw_pcu_init(struct ath5k_hw *ah, enum nl80211_iftype op_mode); /* Queue Control Unit, DFS Control Unit Functions */ int ath5k_hw_get_tx_queueprops(struct ath5k_hw *ah, int queue, |