summaryrefslogtreecommitdiffstats
path: root/drivers/net/wireless/ath
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/net/wireless/ath')
-rw-r--r--drivers/net/wireless/ath/ath5k/base.h4
-rw-r--r--drivers/net/wireless/ath/ath5k/eeprom.c2
-rw-r--r--drivers/net/wireless/ath/ath5k/phy.c6
-rw-r--r--drivers/net/wireless/ath/ath9k/rc.c2
4 files changed, 7 insertions, 7 deletions
diff --git a/drivers/net/wireless/ath/ath5k/base.h b/drivers/net/wireless/ath/ath5k/base.h
index b72338c9bde..952b3a21bbc 100644
--- a/drivers/net/wireless/ath/ath5k/base.h
+++ b/drivers/net/wireless/ath/ath5k/base.h
@@ -36,7 +36,7 @@
*/
/*
- * Defintions for the Atheros Wireless LAN controller driver.
+ * Definitions for the Atheros Wireless LAN controller driver.
*/
#ifndef _DEV_ATH_ATHVAR_H
#define _DEV_ATH_ATHVAR_H
@@ -190,7 +190,7 @@ struct ath5k_softc {
struct ath5k_txq *cabq; /* content after beacon */
int power_level; /* Requested tx power in dbm */
- bool assoc; /* assocate state */
+ bool assoc; /* associate state */
bool enable_beacon; /* true if beacons are on */
};
diff --git a/drivers/net/wireless/ath/ath5k/eeprom.c b/drivers/net/wireless/ath/ath5k/eeprom.c
index 644962adda9..81ea52c4faf 100644
--- a/drivers/net/wireless/ath/ath5k/eeprom.c
+++ b/drivers/net/wireless/ath/ath5k/eeprom.c
@@ -1492,7 +1492,7 @@ ath5k_eeprom_read_target_rate_pwr_info(struct ath5k_hw *ah, unsigned int mode)
* This info is used to calibrate the baseband power table. Imagine
* that for each channel there is a power curve that's hw specific
* (depends on amplifier etc) and we try to "correct" this curve using
- * offests we pass on to phy chip (baseband -> before amplifier) so that
+ * offsets we pass on to phy chip (baseband -> before amplifier) so that
* it can use accurate power values when setting tx power (takes amplifier's
* performance on each channel into account).
*
diff --git a/drivers/net/wireless/ath/ath5k/phy.c b/drivers/net/wireless/ath/ath5k/phy.c
index bbfdcd5e7cb..72474c0ccaf 100644
--- a/drivers/net/wireless/ath/ath5k/phy.c
+++ b/drivers/net/wireless/ath/ath5k/phy.c
@@ -117,7 +117,7 @@ static unsigned int ath5k_hw_rfb_op(struct ath5k_hw *ah,
/*
* This code is used to optimize rf gain on different environments
- * (temprature mostly) based on feedback from a power detector.
+ * (temperature mostly) based on feedback from a power detector.
*
* It's only used on RF5111 and RF5112, later RF chips seem to have
* auto adjustment on hw -notice they have a much smaller BANK 7 and
@@ -2746,7 +2746,7 @@ ath5k_setup_channel_powertable(struct ath5k_hw *ah,
/* Fill curves in reverse order
* from lower power (max gain)
* to higher power. Use curve -> idx
- * backmaping we did on eeprom init */
+ * backmapping we did on eeprom init */
u8 idx = pdg_curve_to_idx[pdg];
/* Grab the needed curves by index */
@@ -2848,7 +2848,7 @@ ath5k_setup_channel_powertable(struct ath5k_hw *ah,
/* Now we have a set of curves for this
* channel on tmpL (x range is table_max - table_min
* and y values are tmpL[pdg][]) sorted in the same
- * order as EEPROM (because we've used the backmaping).
+ * order as EEPROM (because we've used the backmapping).
* So for RF5112 it's from higher power to lower power
* and for RF2413 it's from lower power to higher power.
* For RF5111 we only have one curve. */
diff --git a/drivers/net/wireless/ath/ath9k/rc.c b/drivers/net/wireless/ath/ath9k/rc.c
index c915954d4d5..70fdb9d8db8 100644
--- a/drivers/net/wireless/ath/ath9k/rc.c
+++ b/drivers/net/wireless/ath/ath9k/rc.c
@@ -880,7 +880,7 @@ static bool ath_rc_update_per(struct ath_softc *sc,
* Since this probe succeeded, we allow the next
* probe twice as soon. This allows the maxRate
* to move up faster if the probes are
- * succesful.
+ * successful.
*/
ath_rc_priv->probe_time =
now_msec - rate_table->probe_interval / 2;